UDC 621.862.215.3.082.8 DEUTSCHE NORMEN. December 1972
inte can be given in respect
No guaral
(of this translation
1+ Oevnchen Normencwtshuteh
ut mis Ganehaigung
Countersunk (Fiat) Head Tapping Screvs
with Croaa Rece
Senk-Blechachrauben wit Kreusachiite
Dimensions in m=
Rage of head loft Cat oF Other dinanaiona and
mt tamufacturer'e choice Getatte aa for Type 8
ay
=P according to
DIN’ 7970
Designation of » counterounk (flat) head tapping ecrew with cone end (R) of 3.5 mm nominal dinn-
eter and Length’ Us 19 ma:
Tapping screw B 3.5 x 19 DIN 7902
29 [33 | 3a)
35 7
Warp
Wl
203 |
253 + 240
GAB KoFdmyy Fo IOOO
or)
To, according to 150
Nominal dinaetera in brackets are to be avoided wherever possible.
Formally, these tapping screws are mnde in the sizea for vhich weight details are given. It i
not practicable to'Bake the sizen for vuich dashes appear inatend of length data
Technical conditions of delivery and material according to DIN 267 Sheet 12
Finigh: = according to DI 267 Sheet 2
Thread and acrew ends according to DIN 7970
Grown receonen end zecenn pruckrntion gauge according to DIN 7962
For core hols Sanetere wee DIN P95,
TAT Te aot practic
Explanations on page
Alvinvrhou! der Hormblaver durd BeulhVerag Gaul, Barla 30 bod Kale DIN 7982 engl. Preinge-tFare 2 DIN 7982
Jn recent yonra the Technicel Comat ttes 160/TC 2 "Bolte, nate and acee
tion for Standardization (150) han been dealing with 150 Re iationa for tapping screve nnd haw
rican otandarde in full. Corresponding 150 drafte have
Deen internationally standardized. The reconmeadation han bs
alone should be epe-Afied for tapping acreve with elotted
find the new tenven of Dit! 7970, DIN 7971, DIN 7972 nad DIN 7973 therefore gave ocension to. rev
Stondnrde dealing vith crona recena tapping ecreve alno-
‘The new fenues of DIN 7981, DIN 7982 and DIN 7983 are very clonely 4a Line vith the mew 1
DIN 2972 and DIN 7973. tn other vorde the head dimensions of the acreva agree. ‘The only exception 4a
DIN 7981. Coaperat vith DIN 7971, the hend of the cream racesaad gerey de not f1nt but domed. For the
fanoe hend dinneter and fe volume of upact, therefore, the reeultiag hend helghte are
arentar fo ‘scrave according to DIN 7381 than for slotted hend acrave according to
Bin 91. ‘ereve 8 also conditioned by prenavorking ronacne, wince it
An very @ifticult to, tmpr in fiat pan hende
pitch thrand (Type A) hitherto ia use haa not teen accepted by 100, it haw ceased to be
Socluded tn the present new Lesuew of DIN 7981, DIN 7982 and DIN 7983. It should be noted, hovever, that
tie Tollowing 150 Reressondatione regarding tapping ecreum provide different typa itter aystale. for
facreve vith cone end end ncreva vith {lat end, These type Lettar aysbola have doe bean ainpted because
thin vould have entailed ending exiating docusents ard so addition would hgve aade it necesaary to une
Aifterent standard specification auabere. lence the following aitvation has srinea:
Type B vith cone end according to DIN = Type AB according to 190
Type AZ with fet end according to DIN = Type B according to 150
It Ao appropriate at thin etnge to drav attention to the posasbility of confusion.
the thrend, ‘The 150 numbere have been
Compared vith the previous Jonues of the etandarda, the depths of penetration of the cronm recenas
been changed An sone cases. Practical use and appropriate tents have chown that corrertiona ware nec
in order to pravent hend frncturee (fractures occurring between the bottos of the crouse recess and. the
crew whan)» :
Wit regard to technical conditions of delivery and extersala, reference has deen sade to DIN 267
Sheet ie (nt prevent circulating aa draft), Thie draft atnndnrd Likewise agrees with an 160 Recor
{lon in course of preparation
nin
The foreroing Fxplanationa have venn taken over unchanged {rom the July 1970 inoue of the Standard becmuce
they ure mul} equally valld ned for the pursoge of thin new feove Lt wae only neccesary to correct m