Professional Documents
Culture Documents
Яндекс Переводчик
Before removing the steering wheel assembly and driver's air bag module assembly, refer
to GROUP 52B - Service Precautions and Air Bag Module(s) and Clock Spring .
Position the steering wheel in the straight-ahead position, and remove the ignition key. If
you fail to do this, clock spring for SRS may get damage not to operate the SRS (air bag),
and it may cause the serious injury of the driver.
caution The parts indicated by * are the bolts with friction coefficient stabilizer. Prior to reinstallation,
ensure there is no damage, clean dust and soiling from the bearing and thread surfaces,
and tighten them to the specified torque.
After the installation, perform a calibration for the ASC-ECU to learn the steering wheel
sensor neutral point. (Refer to GROUP 35C - On-vehicle Service, Steering Wheel Sensor
Steering Wheel and Air Bag Module Assembly Centremember Assembly Installation (Refer to
Removal (Refer to GROUP 37 - Steering
).
Wheel ). Lower Arm Assembly Installation (Refer to
Engine room under cover front A, B and Engine
room side cover Removal (Refer to GROUP 51 GROUP 33 - Lower Arm ).
Stabilizer link Installation (Refer to GROUP 33 -
- Under Cover ).
Stabilizer link Removal (Refer to GROUP 33 - Stabilizer Bar ).
Engine room under cover front A, B and Engine
Stabilizer Bar ). room side cover Installation (Refer to GROUP
Lower Arm Assembly Removal (Refer to
51 - Under Cover ).
GROUP 33 - Lower Arm ). Clock Spring Centring (Refer to GROUP 52B -
Centremember Assembly Removal (Refer to
Driver's Air Bag Module ).
). Steering Wheel and Air Bag Module Assembly
Installation (Refer to GROUP 37 - Steering
Wheel ).
Using your fingers, press the dust cover to
check for a crack or damage (Refer to GROUP
37 - On-vehicle Service ).
Front Wheel Alignment Check and Adjustment
(Refer to GROUP 33 - On-vehicle Service,
Front Wheel Alignment Check and Adjustment
).
<LH drive vehicles>
5.0 ± 2.0 N·m
70 ± 10 N·m Removal
50 ± 5 N·m
2 steps
10
<4WD>
1N 1. Steering
11 36 ± 6 N·m >>C<< column bolt
25 ± 5 N·m
5 9 2. Steering
50 ± 5 N·m 3N
<2WD> >>C<< column shaft
4
31 ± 4 N·m
assembly
and steering
6 31 ± 4 N·m gear and
53 ± 8 N·m* 7 6 linkage
5 7 assembly
connection
<<A>> 3 Self-locking
8
nut (Tie-rod
end and
12 knuckle
connection)
4. Rear roll
110 ± 11 N·m* BCD01589AA stopper
centre bolt
<<B>> • Front axle
crossmember
assembly
5. Rear roll
stopper
>>B<< 6. Stabilizer bar
bracket
>>B<< 7. Stabilizer
bushing
>>B<< 8. Stabilizer bar
>>A<< 9. Joint cover
grommet
10. Heat
protector
11. Steering gear
and linkage
assembly
12. Front axle
crossmember
2 <RH drive vehicles>
10 1 N Removal
36 ± 6 N·m steps
5.0 ± 2.0 N·m 9 70 ± 10 N·m
1. Steering
25 ± 5 N·m
>>C<< column bolt
50 ± 5 N·m
3N
2. Steering
>>C<< column shaft
11
assembly
31 ± 4 N·m
and steering
4 gear and
53 ± 8 N·m 6
31 ± 4 N·m linkage
5 7 6 assembly
7 connection
8
<<A>> 3 Self-locking
nut (Tie-rod
end and
12 knuckle
connection)
4. Rear roll
110 ± 11 N·m* ACI00387AB stopper
centre bolt
<<B>> • Front axle
crossmember
assembly
5. Rear roll
stopper
>>B<< 6. Stabilizer bar
bracket
>>B<< 7. Stabilizer
bushing
>>B<< 8. Stabilizer bar
>>A<< 9. Joint cover
grommet
10. Heat
protector
11. Steering gear
and linkage
assembly
12. Front axle
crossmember
Steering
column bolt
Steering
Yoke steering column bolt
column assembly ACA00158AB
Insert the steering column bolt into the no-tapped bolt hole, and tighten it to
the specified torque.
Tightening torque: 36 ± 6 N·m
MMC-Manuals.ru