Professional Documents
Culture Documents
Reliable pumping of
medium consistency
pulp
High Efficiency
No fibres to drain
Effective Degassing
Single Mechanical
Seal
Easy Maintenance
1.1092 GB 10.00
Series BM
Range of
Applications
BM pumps are specifically designed to
handle the complete range of medium
consistency pulp. They can be used with
all types of pulp and on all medium
consistency applications.
The pumps were introduced in 1990
and have since then proven to be highly
efficient and reliable for pumping of me-
dium consistency pulp in many
installations.
Reliable
The robust construction of the pump is a
result of extensive testing together with
end users and a leading supplier of proc-
ess equipment.
The well proven ABS bearing assembly
will give a bearing life time of at least 50
000 hours, in most applications the rated
life of the bearings will easily exceed 100
000 hours. Low Energy Optimised Total
The design of the impeller ensures a
fibre free degassing and vibration free Consumption Economy
performance, which together with the The semi-open impellers which run By using BM pumps the overall economy
specially designed liquid ring vacuum against a wear disc have been deve- is optimised thanks to :
pump results in a clean and smooth ope- loped to give optimum performance. The
ration. combination of high efficiency with the ex-
cellent degassing features assures that High reliability
a very low energy consumption is Efficient pumping
Easy Maintenance achieved.
Low water consumption
The BM pumps are built for long, tough,
continuous operation and require only No Environmental No fibres to drain
infrequent bearing lubrication. Quick and easy
The pump is fitted with a single Influence maintenance
mechanical seal of well-proven design. The ABS medium consistency concept has
The seal is mounted in a seal cartridge a very low water consumption. Apart from
which can be replaced quickly if the seal the mechanical seal quench, all sealing
should become worn or damaged. water is returned to the process.
BM pumps are part of the ABS modular By connecting the outlet of the vacuum
systemTM which ensures availability of pump to the stand pipe, fibres are
spare parts and low maintenance costs. prevented from going to drain.
2
Series BM
Design
Principle Impeller
BM pumps are of a centrifugal design and The impeller and rotor have been ex-
built to handle pulp with a consistency of tensively tested for long periods. The de-
7-17 %. Shaft speed can be varied from sign gives a smooth running without vi-
1200 rpm to 2200 rpm depending on bration and ensures fibre free degassing.
pump size. The pumps are suitable for
variable speed control or continuous
speed drive. Bearing Assembly
Series BM utilise our largest and most
rugged modular bearing assemblies. The
Modular Design bearings are normally grease lubricated,
with a cooling fan to maintain the correct
The pump casing, wear disc and bearing
temperature, even in high temperature
assembly are standard components. The
environment.
bearing assembly has been used in our
BA stock pumps for many years with ex-
cellent results.
Shaft Seal
The shaft seal is a single mechanical seal
with a secondary labyrinth seal. It should
normally be provided with a external
sealing liquid for lubrication and flushing.
3
Series BM
Pumping
ABS medium consistency pumps operate very similar to the ordinary stock pumps.
The BM series is, however, unique in its ability to handle the air in the pulp, which
increases as the consistency changes from the low consistency to the medium consi-
stency range.
4
Series BM
Pumping equipment
Stand pipe Degassing
Install the pump as close as possible to the The degassing valve (7) is a pneumatic
stand pipe or stock chest, to reduce the on/off valve, which should be closed when
suction losses that occur when pumping the pump is not in operation to prevent
medium consistency pulp. pulp from entering the degassing system.
When installing against a stand pipe (1), The degassing valve should also be
its diameter should be such to allow closed when rapid changes in consistency
sufficient dwell time for stable operation. or speed occur, i.e. during starting or
stopping. The signal for the valve can be
obtained from the motor frequency con-
Level control verter or the discharge control valve po-
To ensure that the pulp enters the pump, a sitioner.
minimum positive suction head of 2.5 to 3 The vacuum valve (8) regulates the
meters is required. vacuum in the degassing system. This
To control this level we use a signal from valve is a preloaded ”pirate air” valve.
a level indicator (2). This level indicator can Typical vacuums are 4-6 m absolute.
be supplied by ABS. The actual figure depends on the instal-
lation and is adjusted during start-up.
When commissioning a system, set the
Suction valve to a spring compression at about
As mentioned above, the pump suction must 15 mm and read off the vacuum on the
be as short as possible to keep the suction vacuum guage (9).
losses to a minimum. Therefore the suction
diameter should be as large as possible,
recommended diameter is 400 mm. Vacuum pump
To facilitate service with a full stock chest, a The vacuum pump (10) is a specially
stock valve can be fitted between the chest adapted liquid ring pump in stainless
and the BM pump. To connect the suction pipe steel, which is capable of handling both
to pump inlet, a special flange (3) is used. If a water and fibres without damage.
valve is required, it should be placed between Normally, however, there are no fibres in
the flange and the stand pipe. the degassing system.
This pump is regulated along with the
BM pump to suit individual installations.
Discharge It is driven by a flange mounted motor. As
11 In installations where the pump is running it is mounted separately, it is easy to ser-
at constant speed, either direct or with a vice.
belt drive unit, fit a control valve (4) on the The vacuum pump discharge (11) is
pump discharge. connected direct to drain. In installations,
To reduce losses, the pressure pipe (5) where its sealing water cannot run to
diameter needs to be relatively large. To drain, it can be returned to the stand pipe.
minimise costs, increase pipe diameter
after the control valve.
Baseplate
The common baseplate is of fabricated
Sealing water steel construction, sized for the pump and
The sealing water control system (6) motor, or belt drive unit and motor, with
consists of three Flomatic regulators fixed the vacuum pump mounted on a small ex-
to the lifting arm socket on the baseplate. tension at one side. It also includes the
Flomatic fixings and lifting arm foot for
10 Flomatic (1) regulates
ease of maintenance.
flushing water to the interface of
the mechanical seal.
5
Series BM
Head 30-160 m
Technical Data
m
200
Temperature max.92-93°C
250/150-67 1500 r/min
300/200-67
200/100-40 1500 r/min
Material
ABS Equivalent grades Chemical
Series BM is delivered with Material Germany USA Composition
all wetted parts in stainless
steel 2324 and 2562/2564. 2324 1.4460 AISI 329 24Cr 5Ni 1.5Mo 0.10C
2562 1.4539 UNSN 08904 20Cr 25Ni 4.5Mo 1.6Cu 0.025C
2564 - A743/CN-7 M 20Cr 25Ni 4.5Mo 3.5Cu 0.06C
Stand
pipe
Alt. 2
Emergency Outlet to
dilution stand pipe
BM pump
Control
valve
Alt. 1
Outlet to
Sealing water drain
Vacuum
Degassing pump
valve
6
Series BM
Dimensions
Bearing Assembly 4F
g f
g f h2
q
DN2
max. 2000
DN2 Q1
Q1 Q3
Q3
h2
DN1
DN1
h1
h3
h3
h5
h5
L1 B1 B2
L1
BM 200/100-40 200 100 840 135 180 770 280 400 705 220 2500 280 335
BM 200/150-40 200 150 840 135 180 770 315 450 705 220 2500 305 340
*) Pump only Q1 = Pressure gauge Q3 = Sealing liquid
h2
g f
Bearing Assembly 5F q
DN2
Q1
Q3
h2
DN1
h1
h3
h5
L1 B1 B2
BM 250/150-67 250 150 1020 135 215 932 450 630 725 240 2800 469 855
BM 250/200-48 250 200 1020 135 205 943 450 530 725 240 2800 415 680
BM 300/250-60 300 250 1020 135 200 905 450 675 725 240 2800 476 750
h2
g f q
Bearing Assembly 6F DN2
Q1
Q3
h2
DN1
h1
h3
h5
L1 B1 B2
BM 300/200-67 300 200 1120 135 200 1080 450 675 725 240 3100 476 1065
7
Series BM