You are on page 1of 32
ension CODE || Maximum Marks :100 Total Duration 150 Minutes Seriat 117633 Maximum Time For Answering :120 Minutes. | Number: Subject: ELECTRICAL SCIENCES (E & E/E & C/TC/IT/BME/ME) ee 2 | P-ELS | Dos: 4. This question booklets issued to you by the invigilator after 02.20 pm. 2. Check whether the PGCET Number has been entered and shaded in the respective cir ‘answer sheet. 3. The version code and serial number of this question bookiet should be entered on the OMR answer sheet and the respective circles should also be shaded completely. 4. The Version Code and Serial Number of this question booklet should be entered on the Nominal Roll without 1s on the OMR any mistakes. ‘5. Compuisorily sign atthe bottom portion of the OMR answer sheet in the space provided. DONTTs: 4. The timing and marks printed on the OMR answer sheet should not be damaged / mutilated / spoiled. 2, The 3* Bell rings at 2.30 p.m. til then; © Do not remove the seal present on the right hand side ofthis question booklet. © Do not look inside this question booklet or start answering on the OMR answer sheet IMPORTANT INSTRUCTIONS TO CANDIDATES Incase of usage of signs and symbols in the questions, the regular textbook connotation should be considered Unless stated otherwise. 2. This question booklet contains 75 questions and each question will have one statement and four different ‘options / responses & out of which you have to choose one correct answer. 3. After the 3rd Bellis rung at 02.30 pm, remove the paper seal on the right hand side of this question booklet and check that this booklet does not have any unprinted or tom of missing pages or tems ate, if so, gat it replaced by a complete test booklet, Read each item and start answering on the OMR answer sheet. 4. Completely darken / shade the relevant circle with a blue or black ink ballpoint pen against the question number on the OMR answer sheet. aS ‘3x, BELTS WRONG METHOD corRECTMETHD | © © O O©OOG DOS ®@© O|}F8 HOG ®GHOSOD '5. Please note that even a minute unintended ink dot on the OMR answer sheet will also be recognized and recorded by the scanner, Therefore, avoid multiple markings of any kind on the OMR answer sheet. 16. Use the space provided on each page of the question booklet for Rough Work. Do not use the OMR answer sheet for the same, Last bell will ring at 4.30 pm, stop marking on the OMR answer sheet. Hand over the OMR answer sheet tothe room invigllator as its. 9. After separating the top sheet (KEA copy), the invigilator will return the bottom sheet replica (candidate's copy) to you to carry home for self-evaluation 10. Only Nom-programmable calculators are allowed for "M.E/M-Tech/M.Arch” examination. Marks Distrib Part—A: (Section 1) 30 Questions: 30 x 1= 30, (Section 2) 15 Questions: 15 x2 = 30 art—B : | (Section #) 20 Questions: 20 x 1 = 20, (Section 2) 10 Questions: 10 x2 = 20 2 = — RPoolegs esariL at ELECTRICAL SCIENCES (Common to E&E /E&C/TC/BME & ME/IT) PART—A (SECTION - 1) Each question carries one mark. (30*1=30) a eee feet ieeea[e 4. If (9) Is the probability of r given by i ae ee wo p(n = (2.083) @ °° the distribution is on called 2 (@) Binomial © 3 (@) Normal (©) Poisson 2. tusx+y? then eae (0) Exponential (A) -1 5, The equation ie P'vax =! yy+y, +40, +¥gte)* ma [vax =F ory, * 404+ Ys +2, tyqtonllls (D2) 2 called in numerical integration (A) Trapezoidal rule 3. Thelinear form of the differential equation (8) Simpson's rule oy cat ys evils {C) Weddle's rule az (0) Romberg integration wy SB ieee © 1g integ) oy az axe . i of eee if X=x+ywith y(o)=1 then by Euler's oz : ‘method y (01) at h = 01s, © & pte wy an @ 3n oz O & Se (©) 2m (© 1 ‘Space For Rough Work When two meshes ha dependent -or Independent current source in common, we can call (A) Dependent Mesh (@) Independent Mesh (C) Super Node (0) Super Mesh Norton's equivalent resistance is the as Thevenin's equivalent resistance (A) Not same () Same (C) Both A and B (0) None of the above ‘Superposition theorem is not applicable for (A) Voltage calculations (8) Bilateral elements {C) Power calculations (0) Passive elements 10. While considering reciprocity theorem, we consider ratio of response to excitation as ratio of (A) voltage to voltage (8) current to current (©) voltage to current (0) none of the above ) 11. Which elements act as an independent variables in ¥-parameters? (A) Current (8) Voltage (©) Both AandB {P) None of the above 12. Which of the following error is caused by poor calibration ofthe instrument? (A) Random error (8) Gross error (©) Systematic error (©) Precision error ‘Space For Rough Work At P-ELS AP collegedunia 13. When using even parity, where is the parity bit placed? (A) After the odd parity bit (8) After the LSB (C)_ Inthe parity word (0) None of the above 14. DC power output of center tapped full wave rectifier is equal to (1, is the peak current and R, is the load resistance) (A) (21,292), @) 272m) R, (©) ,2)R, (0) (41,27), 15. Which type of power amplifieris biased for operation at less than 180° of the cycle? 16. "7. 18. (One of De Morgan's theorems states that X=Y-XY. Simply stated, this means that logically there is no difference between: (A) aNORand an AND gatewith inverted inputs (8) aNANDandan OR gatewith inverted inputs (C) anANDandaNORgatewith inverted inputs (0) aNORandaNAND gatewithinverted inputs 15 A.J-K flip-flop with J= and K = thas a 20 kHz clock input. The @ output is. (A) Constantly LOW (8) Constantly HIGH (©) A20 kHz square wave (0) A 10 kHz square wave The phase difference between the input and output voltages of a transistor connected in common collector arrangement is, (A) Class A (A) 180° 8) Class B or AB (8) Class eo (©) Class ¢ (© 90° (0) Class 0 (0) 270° ‘Space For Rough Work P-ELS 5 — MPeollegedu iat 19. 20. 21. In case of DC servomotor, the back emf is equivalent to an electric friction which tends to: (A) Slowly decrease the stability of the system (8) Improve stability of the system (C) Very rapidly decrease the stability of the system (0) Have no effect of stability ‘The overall transfer function from block diagram reduction for cascaded blocks is: (A) Sum of individual gain (8) Product of individual gain (C)_ Difference of individual gain (0) Division of individual gain Routh Hurwitz criterion cannot be applied when the characteristic equation of the system containing coefficients which is/are (A) Exponential function of s (B) Sinusoidal function of s (C) Complex (0) Exponential and sinusoidal function of sand complex 22. 23. Which one of the following is not the property of root loci? (A) The root locus is symmetrical about Imaginary axis (8) They start from the open loop poles and terminate at the open loop zeroes {C)_ Thebreakawaypointsare determined from dk/ds = 0 (0) Segments of the real axis are the part of the root locus if and only ifthe total number of real poles and zeroes to thelr right is odd A closed loop control system is stable if the Nyquist plot of the corresponding ‘open loop transfer function (A) Encircles the s-plane point (-1, 0) in the clockwise direction as many times as the number of right half s-plane poles (®)_Encircles the s-plane point (-1, 0) in the counter clockwise direction as many times as the number of right half s-plane poles {C) Eneircles the s-plane point (-1, 0) in the counter clockwise direction as many times as the number of left half s:plane poles (©) Encircles the s-plane point (-1, 0) in the counter clockwise direction as many times as the number of right half s-plane poles zeros ‘Space For Rough Work at P-ELS PMP collegedunia 24, State space analysis is applicable even if | 28. The ADCO804 has resolution the initial conditions are (A) Abit (A) Non-zero (8) Zero eet (©) Equal (©) tit I (0) Not equal © a2bn 25. What is the file extension that is loaded in a microcontroller for executing any | 29. What should be done if we wantto double instruction? Goal voter, (A) hex (A) change a bit of the TMOD register () ot (B) change a bit of the PCON register ice (8) chang si (0) doe (©) change a bit of the SCON register 26. An alternate function of port pin P3.4 in Oh. Sinnge SaitotINS EUR Rater, the 8051 is Teel 30. USART abbreviated as (8) TimerO (©) Interrupt (A)_universalsynchronous-asynchronous: (©) Interrupt o Recelver-transfer (8) universal asynchronous-synchronous 27. Which of the following instructions will load the value 35H into high byte of timer 0? RI (&) MOV THO, #281 (©) united —asynchronoiss-synchronous (8) MOV THO, 35H Receiver-transmitter ~ (© Mov TO, #354 (0) universalsynchronous-asynchronous (©) Mov To, 35H Recelver-transmitter ‘Space For Rough Work P-ELS AL 7 fie Seal (SECTION - I!) Each question carries two marks. 20 -4x+7 (15 x 2=30) 34. In the circuit given below, the current [1] in : 3A. The limit of 35; 50=4 at x= © the 4-ohm resistor is is 2a 20 ore et ey u Wa av Seo S40 4 @ = 1 5 2 \ ee 358 @) 258 3 () 154 (@)-O5A (0) oO 35. The Norton equivalent of the circuit shown 32. If 8x — 10y + 66 = 0 and 40x - 18y = 214 in the figure is then correlation value is r= 1 (a) 04 dae hl (©) 06 | y (©) 08 (A) 0758, 5/6 Ohm (0) 09 (8) 0.75 A,1.5 Ohm (©) 18,15 0hm 33. Ify(0)=1,y(0.5)= 08 and y (1)=05, then Deas 78) (0) 1A,5/6 Ohm by numerical integration using trapezoidal nde the value ts 36. Find the force between two charges when (a) ots they are brought in contact and separated by 4cm apart, charges are 2nC and ~1nC, (®) 0225 isi © 001s (a) 144 @ 244 (©) 0775 (C) 2.404 (2) 1404 ‘Space For Rough Work 8 P-ELS APP collegedunia 37. Choose the incorrect statement(s) from | 39. Determine the output frequency for the the following: circuit given below: (1) MROM does not allow the storage of user specified data to the manufacturer of the memory (2) PROM can be reprogrammed again and again at any number of times (3) EPROM allows to erase the stored content by direct exposure of chip to UV radiations every time before are () 28.7 Hz (4) E? PROM allows erasing in an (8) 31.97Hz electrical manner despite the exposure of chip to UV rays: ores (A) 1&2 (0) 39.47Hz (8) 3&4 ose 40. For the block diagram shown in Fig the transfer function of the system is given (©) 284 a a 38. The subtraction of a binary number ¥ from =o es ee oy another binary number X, done by adding *y the 2's complement of Y to X, results in fa binary number without overfiow. This implies that the result is is : (A) negative and isin normal form (®) negative and is in 2's complement (A) G1+62+63/(1+ 6264) eu) (8) G1G2+6263/[1+62G4] (©), positive and is in normal form (©) 6162+62/(1+ 6264) (©) positive and is in 2's complement form (0) G1G2/[1+63G4) ‘Space For Rough Work P-ELS At Se Pe ceccthia 41, Use Mason's gain formula to find the | 44, What is the Time Delay generated by transfer function of the given signal flow hee graph shown in: cnn Semen ‘ Given Crystal Frequency = 11059 MHZ Leavyfan Ns * Delay : Mov R,, #2004 ye tas Here : DINZR,, Here () aba tt RET (B) abdeg / [1 ~ (be + ef) + beef] (A) 436.25 us : (C) abd /[1— (be + ef) + beef) (0) adedef /[1 - (bc + eff + beef] (8) 3001S 42, Thenumberand direction ofencirclements (©) 500 us around the point (—1 + jO) in the complex plane by the Nyquist piot of (©) 800.26 ys Gla) = (1-5) /(4 +25) 18 () zero 45, What isthe content of Accumulator (8) one, anti-clockwise after this operation? (©) one, clockwise were (0) two, clockwise XRLA, #45H 43, Whats the Hex Decimal value loaded into ips CCH the TH1 Register Mov TH, # -200 (®) 45H caH (@) OH (© 24 (©) FAH (0) 38H i ae ‘Space For Rough Work 10 P-ELs PP collegedunia (E&E: ELECTRICAL AND ELECTRONICS ENGINEERING) PART -B (Section-I) Each question carries one mark. 46. The synchronous impedance method Will not give accurate voltage regulation because (A) Thevalue of synchronous impedance found is always less than actual value (8) The value of synchronous impedance found is always more than the actual value (©) The value of the synchronous impedance is independent of saturation () The reactance due to armature reaction is considered separately 47. The torque produced by a series ‘combination of two DC series motor is (A) Half the torque when they are connected in parallel (8) Twice the torque when they are connected in parallel {C) Four times the torque when they are connected in parallel (0) Equal to the torque when they are connected in parallel (20«1= 20) 48, Which of the following test can be 49. ee a (A) Swinburne test (8) Hopkinson test (C) Brake test (0) Field test How many cycles of alternating current will be generated in one revolution of 8 pole synchronous alternator? (A) 10cycles (8) 8cycles (©) cycles (0) 16 cycles Which of the following is the main advantage of an autotransformer over a two winding transformer? (A) Hysteresis losses are reduced (8) Saving in winding material {C)_ Copper losses are negligible (0) Eddy losses are totally eliminated Space For Rough Work P-ELS " — MP collegedunia 51. Compared with the secondary of a loaded step-up transformer, the primary has (A) Lower voltage and higher current (B) Higher voltage and lower current {C)_ Lower voltage and lower current {0) Higher voltage and higher current 52. Which of the following connections is most suitable and economical for small, high ~ voltage transformers? (A). Deltadelta connection (8) Ster-star connection (©) Stor-delta connection (©) Delta-star connection 53, Ferranti effect can be compensated by which of the following? (A) Shunt Reactor (8) Series Capacitor (©) Shunt Capacitor (0) BothA&e 54, In practice what is the value of diversity factor? (A) Less than Unity (8) Greater than Unity {C)_ Equal to or greater than Unity (0) Less than zero 55. When load factor and diversity factor increase (A) Cost of electricity decreases (G) Cost of electricity also increases (©) Cost of electricity remains same (0) Cost of electricity increases ‘exponentially 56. An SCR has half cycle surge current rating of 3000 A for 50 Hz supply. One cycle surge current will be (A) 15008 (®) 6000a (©) 2121324 (©) 4202644 57. Which triggering is the most reliable? (A) Forward voltage triggering (8) Gate triggering (©) dV/dt triggering (©) Thermal triggering 58. Snubber circuit is used with SCR (A) inseries (©) inparattel (©) elther series or parallel (©) anti-paratte! ‘Space For Rough Work 2 AL P-ELS AP collegedunia 59. A modern power semiconductor device that combines the characteristics of BJT and MOSFET is, (@) IceT () mcT (®) FCT (2) GTO 60. What is infinite bus in power system? (A) Alarge system with infinite voltage (8) A large system in which the voltage and frequency vary (©) A large system whose voltage ‘and frequency remain constant throughout. (©) Both (A) and (8) 61. Normally Z bus matrix is a (A) Null Matrix (8) Sparse Matrix (C) Full Matrix (0) Unit Matrix 62. Single line diagram does not represent: (A) Star connection of transformer winding (B) Delta connection of transformer winding (©) Neutral wire of transmission lines (0) Ratings of machines 63. DC series motors are used where the high torque is required. (A) Maximum (©) Minimum i (©) Starting (0) Stalling 64, Which starting method is the best method in induction motor? (A). Direct online starting (8) Autotransformer starting (©) Reactance starting (©) Star-Delta starting 65. The speed control by variation of field flux results in. (A) Constant torque drive (®) Zero speed {C) Variable torque drive (0) Variable power drive ‘Space For Rough Work B a MP collegedunia (Section - I!) Each question carries two marks. 66. A 3-phase, Y connected, round rotor synchronous generator rated at 10 kVA, 230V has a Synchronous reactance of 4.20 perphase and anarmatureresistance of 0.5 © per phase. The percentage voltage regulation at fulload with 0.8 lagging power factor is (A) 21.89% (®) 18.91% (©) 257% (0) 20.45% 67. An alternator is generating power at 210 V per phase while running at 1500 tpm. If the speed of an alternator drops to 1000 rpm the generated voltage per phase will be (a) 15V (®&) ov (©) 20 (0) 150v 68. A 600 KVA transformer has iron losses ‘of 400 kW and copper losses of 500 KW. Its KVA rating for maximum efficiency is (10 « 2= 20) 69. A'S KVA transformer has a turns ratio of NVN2 = 10. The impedance of primary windings is 3 + j5 ohms while that of secondary winding is 0.5 + j0.8 ohms. The impedance of transformer when referred to primary will be (A) 35+)5.8 ohms (8) 8+)13 ohms (C) 53+)85 ohms (0) 3.05 +)5.08 ohms 70. A voltage of 1000 kV is applied to an overhead line with its receiving end open. If the surge impedance of the line is 500 ohm, then the total surge power in the line is (a) 2000 mw (8) 1000 mw {¢) 10000 mw (0) 200mw 71. An overhead line conductor has a cross sectional area of 2.5 cm?, span length is 250 m, weight of conductor 1.5 kg/m, allowable maximum tension 6666.67 kg, wind pressure is 40 kg/m*. Calculate the oe. deflected sag. (a) 537 kVA a ee en (®) 226m (©) 555KVA (¢) 026m (0) SeskvA (0) 185m Space For Rough Work P-ELS AP collegedunia 72. Ifa latching current for the circuit shown in Fig. 1 is 2 mA. Obtain the value of minimum width of the property turn ON the SCR? Pot (sama A) 3s (®) 34s (©) 32us — (D) 33ys 73. Find the value of R in case of an RC firing circuit which is to be turned ‘on with a source voltage of 150 74. 8. ‘A motor load system has following details: Quadrants. 1 and Il, T = 400 - O4N, N - m; where N is the speed in rpm. Motor is coupled to an active load torque T1= + 200, N—m. The motor speeds for motoring and braking operations in the forward direction are (A) 400 rpm, 500 rpm (8) 1000 rpm, 800 rpm (©) 500 rpm, 1500 rpm (0) 500 rpm, 1000 rpm ‘A3— phase, 6 pole, 50 Hz, Y ~ connected, squirrel - cage induction motor has following parameters: time constant 0.4884 sec and slip = 0.1197. The time taken by the motor during starting is. (A) 1107 sec Vand the following parameters: (@) 1505 sec Igt = 2A, Vd = 1.5V, Vat = 125 V. (C) 0.995 sec “ 1759 (8) 54.250 (D) 1.297 sec (©) 960 ©) 50 ‘Space For Rough Work P-ELS = = PP collegedunia (E& CAND TC: ELECTRONICS AND COMMUNICATION ENGINEERING AND ‘TELECOMMUNICATION ENGINEERING) PART -B (Section - 1) Each question carries one mark. 46. In VLSI design, which process deals with the determination of resistance and capacitance of interconnections? (A) Floorpianning (®) Placement & Routing (©) Testing (0) Extraction 47, The BJTs in the BICOMS circuit isin configuration. (A) Push-pull (®) Totem pole (©) Active high (0) Active low 48. The CMOS inverter consists of: (A) Enhancement mode n - MOS transistor and depletion mode MOS transistor (8) Enhancement mode p - MOS transistor and depletion mode 11-MOS transistor (C) Enhancement mode p - MOS transistor and enhancement mode p-MOS transistor (0) Enhancement mode p - MOS transistor and enhancement mode f= MOS transistor (20x 1=20) 49. Which mathematical notation specifies the | condition of periodicity for a continuous time signal? (A) x) =x (t+ T) (8) xin)=x(n +N) (©) xy=e* (0) None of the above 50. A LTI system is said to be initially relaxed system only if, (A) Zero input produces non-zero output (8) Zero input produces zero output (C)_ Zero input produces an output equal tounity (0) None of the above 51. A.causal and stable 11 filter has (A) Linear phase (8) NoLinear phase (©) Linear amplitude (2) Noamplitude ‘Space For Rough Work 16 P-ELS AP collegedunia 52. The z-transform of a sequence x(n) which is given as X(z) = Eo n= =x x(n) z- nis known as (A) Unilateral Z - transform (B) Bilateral Z - transform (©) Trilateral Z - transform {D) None of the mentioned 53. In MSK, the difference between the higher and lower frequency is (A) Same as the bit rate (®) Half of the bit rate (©) Twice the bit rate (0) Four times the bit rate 54. US digital cellular system based on CDMA was standardized as (@) Is~54 (®) Is-136 (©) 1s-95 (0) 1s-76 55. What is the disadvantage of FM over AM? (A)_ high modulating power is needed (8) requires high output power (©) large bandwidth required (©) high noise is produced 56. 57. ‘An antenna has a field pattem E (0) =c0s (0), cos 2 (9). The first null beam width of the antenna is: (A) 45° iG I (Cc) 180° (0) 120° ‘The basic equation of radiation that is applied to any antenna irrespective of the type of the antenna is: (a) iL=Qv (8) iO=W (c) i=aw (0) None of the mentioned A source has a cosine radiation-intensity pattern given by U = U,, cos (0). The directivity of this source is: (ay 2 @ 4 © 6 wo 8 Space For Rough Work P-ELS 7 ee AP collegedunia 59. Choose the correct statements) 60. 0 ) ay i) « © © 0) The gate circuit impedance of MOSFET is higher than that of a BJT The gate circuit’ impedance of MOSFET is lower than that of a BJT ‘The MOSFET has higher switching losses than that of a BJT The MOSFET has lower switching losses than that of BJT Both 18 Both iv Both igi Oniy commutation technique is ‘commonly employed in series inverters. a) @ © 0) line load forced external-pulse 62. The instruction that is used to transfer the data from source operand to destination operan« (A). data copy \ transfer instruction (B) branch instruction (C)_ arithmetic \ logical instruction (0) string instruetion 63. The instruction, MOV AX, 000SH belongs to the address mode is (A) register (8) direct (©) immediate (0) register relative 64, Ifthe data is present in a register and itis referred using the particular register, then itis (A) direct addressing mode (8) register addressing mode (©) indexed addressing mode (©) Immediate addressing mode 65. The addressing mode that is used in unconditional branch instructions is G1. What Is the expression for the current (A) Intersegment direct addressing amplification factor? mode (A) Aleave (®) intersegment indirect addressing mode (8) AveAle (©) intersegment direct and Indirect (©) (AICAIByVCE addressing mode (©) (aicalsyvBe (P) None of the above ‘Space For Rough Work 18 at P-ELS MP collegedunia (Section — I!) Each question carries two marks. 66. Which process is involved in growing the shaded region? ‘Pte subst (A)__ Chemical Vapor Deposition (CVD) (8) Sputtering and patterned by etching (C) Chemical Vapor Deposition (CVD) and patterned by HF acid etching (©) Chemical Vapor Deposition (CVD) and patterned by dry (plasma) etching (10 x 2=20) 67. Which of these inverters is more efficient? Cy eS ee ae, (cy vat © j fivon vee ou 68. Determine energy of power as applicable for the following signal x{n] = (V/3)' u(n] 1a) 10/4 ®) 9/4 © se © 98 ‘Space For Rough Work P-ELS 19 — — PP collegedunia 69. Which of the following is the odd | 73. For 2 half-wave single phase thyristor component ofthe signal x = (i? rectifier circult with any type of load the ae eat ‘waves must ideally give the supply “ ® Voltage waveform. (C) JS*cost (©) sint 70. A parabolic reflector used for reception 7 4 with the direct broadcast system Is 48 inches in diameter and operates at ; 12.4 GHz. The far-field distance for this Re antenna is: 8m @) Bm (A) load voltage, toad current (©) 164m (0) 173m (8) load voltage, thyristor voltage (©). supply current, load vota 71. ifthe field strength at receiving antenna is peeps hb ashen 1iV/m, and the effective aperture area is nee one ee mes 044 mand the intrinsic impedance of the : : mediums a7? izi>ipl (©) lal>izicibl (©) lalibl ‘Space For Rough Work | 22 at P-ELs PP collegedunia 60. The Z transformation x(n) = 6 (n + k) for K>Ois W z/z-1 ® 2 o1 © z* 61. Rapid Eye Movement (REM) sleep is characterised by: (A) High amplitude low frequency EEG waveforms. (8) Reduced skeletal muscle tone. (C)__ Slow rolling eye movements. (0) An onset at the beginning of sleep. 62. For analog and digital IIR fiters to be 63. Gaussian noise is referred to as (A) Red (8) Black (©) Normal noise (©) White 64. The sampled frequency less than the nyquist rate is called (A) Under sampling (8) Over sampling (©) Critical sampling (0) Nyquist sampling 65. Gradient magnitude images are more casual number of zeros must be een (A) > number of poles (A) Point (8)

You might also like