Piping Design hitp:/www.azpiping.com
Smart Plant Review Tips
' This report was downloaded from ~
t http://www.Azpiping.Com/Guide '
t '
Brought to you by Hung Hong
"LL . Website, GlckHere to vist I
I. Layout
Here is typical layout.
‘You can display or hidden any window by right click at toolbar then select menu you want or
using short cut keyPiping Design http://www azpiping.com
Tags Accessories Window Help:
|] oe |#|%+ 4
| Bacttion Control Yet
|e Perepecthe angie Mtate2
1S encircle Radive Altes
Customees,
Il. Change background color
View->Setting->Edit then select color you like.Click OK to finish
Edit [View Tools Motion Tags Accessories |
:
F Sao and Recall cree
8 Spashot
Bhat screen Fu
Toobars >
Stats tar
Project Manager
ILL Zooming in, zoom out on an item,
1. You can use zoom in and zoom out menu at toolbar
col calc | eee Re|sivinao agiara|
ZoomINby2¥ @anaan
2. In Lateral ModePiping Design hitp:/www.azpiping.com
If you slide the “perspective angle”
down, the view cone angle will increase
3. In Encircle Mode
If you slide the “encircle radius” down,
radius will increasePiping Design http://www azpiping.com
-Moving the eye-point closer to the object.
Drag the View Cone on the Plan View
eee ie Runes)
isl
- Other ways, on the Main View Window,
move forward by dragging mouse -up while
holding down the left mouse button.
You need to active forward/back/lefUright
icon
Re
o/tOe ko Vy Baa
aa\a + *o He kla|¥S TRI AQ ArH
(Ferwarcyaack, LetRigrt))
IV. Adjusting the View Cone
1. Adjust Far Clipping Plane
- Left click outside the view cone
- Drag the mouse to desired
position of far clipping plane and
accept by clicking on left button
again,
2. Adjust Near Clipping Plane
- Left click outside the view cone,
- Check if the far clipping plane can
be moved
-Right mouse click and then drag
the mouse to desired position of near
clipping plane and accept by clicking
on left button again.Piping Design hitp:/www.azpiping.com
Y. Rotation around an item
Follow 4 steps below:
1._Click on View Menu -> Place -> Centerpoint Only
[ei cat [Wew Toole Meton Tags Accserae Window Help
|oale
|
ye Puht.criy
tras,
Delay
Acerca
rots Rear
Sap at Fecal
Bo Snapehct
Ful Soeen
ovwan
__Toobars
v Stetus Bar
Project aac
& W 2
2. Double-Left Click on the item -> Left Click. The item will be placed at center of
main view window
or
————S.
3. Click on Rotate button and the Encircle button
I
[oa 6)) Se | aaa) sos
=)
Edit View Tools Motion Tags Arcessories Window Hel
@ 2e)" = naPiping Design hup:/Avww-azpiping.com
4, Now, you can start rotating around the item in the main window by dragging mouse —up-
down-left-right while holding down the left mouse button.
VI. Viewing Model Attributes
_
1
-Click on the Auto-Highlight icon,
-Click on the item and the attributes will
be displayed on the lower pane.
ieee tis
ere eas
VII. Display Sets
-You can define the collection by file,
by level, by color, by line-id, by
equipment number or any attribute and
any combination of attributes.
~ You can change color, hide, unhide
and ete.
1. Create New Display Set.
Clicking on Tools -> Display Set -> New -> Display Sethitp:/www.azpiping.com
Piping Design
jaalay
Click on Insert
Select critical in the drop down menu, eg
Definition
Cet:
La
‘Then click Ok->OK to finish
2, Save and RecallPiping Design http://www azpiping.com
If you want to recall display window later, you need to use Save and Recall Views
[Ble te ew Took Unter Tape asconoree widow | -Click View Menu
ss - Select Save and recall View
6
Barut scm ru
potas ,
Stas oe
- Click on “Add Current View”
- Or “Create Group” if you need to
group all similar saved views
‘Add Current View.
aston |onwarl ver Gre ona Shaner
select "Add
Current View"
scription here oF
To Recall View
-Click on Save and Recall Views
again
- Highlight Saved View to Recall
-Click on Recall View
Click here to recall"
Saved View"
VIII. Measuring DistancesPiping Design hitp:/www.azpiping.com
Or go to Tools -> Measure -> Snaplock
Or Click on Snaplock Measurement icon
i ten Tas ais
eee es seize +lo%
LEE 4 SB sosig obras =
ee
First Point
Click on Snaplock Measurement Icon (Or
press F8 )
Double click near first reference point
-If Red box is the desired reference point,
Left Click again to accept position.
-if not, right-mouse click to reset and move
the red box to other positions
-Once the reference point is accepted, a
blue box will be placed.
Second point:
-Click on Snaplock Measurement Icon ( Or
press F8 )
~ Double click near second point
-If Red box is the desired reference
not, right-mouse click to reset and move
the red box to other positions
oa te Tp eon ree
5
oa “fee e/Re 98 #25 .RABZ| Delete Measureme
cn. =a Delete Measurements
oS ED 3 5% & | -Goto “Tools”
Son "8 | _ Select “Measure”
Saaeeel Htvaeroecr -Select “Delete All Measurements”
‘Sonar sooo eee | (or CirtAll+M)
Stree + fame comers
———— * Aopeee Laeseuerere crm
grown ot