— Abstract of
METRIC SCREW THREADS — M PROFILE ASME B1.13M
THREADS
Benson.) wes
Table 13 Limiting Dimensions of External Screw Threads — Class 6g
vn on tor Beir
— re al Tas
SNS | Atwene z 2 aes
Thread Pitch _ . 3
x07 oa [sare] sess} sas] 000] com sam
Wace bose tae | ieee | ees | oi | Be
mace tse fee | ms | tam | oie | tae
tans boas teees | tose | twee | aim | irae
ors ed tam | wom | fame | aoe | ane
ara o0%8 ‘ane | 00s | oom | ere 1
beer ose Sia | Bie | cae | Rate
oo does oe | Stow | Seve | oa | arose
ane 080 cao | oooa | sora | cao | sas
ceehoee 2 aa 7
—
cceplance is basndon maxim material eondtion gaging,
which may be applied is equal to 0.038 divided
by 6 or 0.0063. This is not sufficient for the re-
quired coating of 0.008, so additional adjust-
ments to the before-coated pitch and major di-
ameters must be made.
To determine the before coating maxi-
mum material sizes, decrease the maximum
pitch diameter of 12.701 by 0.048 (6 x 0.008) to
42,683 and maximum major diameter of 14.000
by 0.024 (3 x 0.008) to 13.976. For the before
coating minimum sizes, decrease the minimum
pitch diameter of 12.601 by 0.032 (4 x 0.008) to
12.569 and the minimum major diameter of
13.720 by 0.016 (2 x 0.008) to 13.704. The
before coating sizes should be included in the
thread designation. (See 7.8.2).Abstract of
ASME SCREW
ASME BLIsM) | METRIC SCREW THREADS — M PROFILE
1995 | | THREADS
nae
Tabie reads - Class 6H
Tajor Diameter
om Thread °
Diaane For Reterence
Tread Pen
in wax iin Tei in Mow
imi 6x038 vai | tae | tar oa | a0 | 1706
Monod ter | tea | 1280 oom | 2000 | aiee
meswoss | 200 | ata | 2208 aoa | 2800 | 2000
hexos zo | os | 2are aio | S000 | Sar |
Mo5x06 2as0 | so | 3110 ore | 3500 |
Imaxor ass one | «000 |
Men08 “890 ors | S000
Mec 5350 0150 | 6000
Me t25 7388 8160 | 8000
Mioxts S26 oreo | too | ro
oases | 11.065 | az00] 2000 | 285 |
wo | 203 | oa | t4c00 | 1480
iz | tama | ose | teo0 | tos0
tase | tesco | ose | coou | doses
zosrs | 2060 | O26 | 22000 | zoce |
zeos; | 2316 | 026s | 24000 | creo |
vias | esos | asi | oaes | arqoo | areae
2am | zrrar | za00r | 9280 | 20000 | sors |
sez | sosoz | asm | o30 | aso | aco |
sre | anor | aoc | oars | dao | soecs
saz | sare | sso | o3as | deo | socsr
so700 | seas | crea | oass | seco | srio
sao | oos0a | aoare | oars | econ | ean
esos | esos | sears | oars | T2000 | Teen
r4308 | 7e109 | 7ea7a | oars | somo | atau
acaos | asios | asare | oars | aco | saat
seas | seis | soso | 0400 | tooo | torzee |
NOTES:
1 See Para. 54.2.
2. Dimensions used i the design of tools, et. In hmensioning intra thveads tis net normally specified, Generally major
sdamoer acceptance is based on maximum matefa concen gaging
3. Fovsizes M105 fs 200 and aerate ca and tvead plches, see complete standar,
8.5.2. Only Nominal or Minimum Coating
Thickness Specified. If no coating thickness
tolerance is given, itis recommended that a tol-
erance of plus 50% of the nominal or minimum
thickness be assumed. Then, to determine be-
fore coating gaging limits for a uniformly coated
thread, decrease (a) maximum pitch diameter
by 6 times coating thickness, (b) minimum pitch
diameter by 4 times coating thickness, (c) maxi-
mum major diameter by 3 times coating thick-
ness, (d) minimum major diameter by 2 times
coating thickness.
Example:
M14 x 2 ~ 4h6h (22) Coating Thickness 0.008
Since allowance for tolerance position g
is 0.088, the maximum thickness of coating