Professional Documents
Culture Documents
P-3002D
P-3002DL / P-3001D
Instruction Manual
Congratulations on your purchase! To get optimum performance of your
"P-3002D" Drum Pedal, please read this Instruction Manual before playing.
Key Bolt
Beater Setting Stopper
Multi Function
Drum Key Beater Holder Link
Bottom Plate
P-3001D Short Footboard
Long Footboard
Attachments
Oil, Velcro Tape (x6), Allen Wrench (3mm, 2.5mm)
Control Core Beater Setting Beater Stroke Adjustment
Insert the Control Core Beater into the Beater Holder Link The P-3002D Demon Drive Double Pedal features our
until it stops against the Beater Setting Stopper, and tighten exclusive two-position Beater Holder that can be positioned
the Key Bolt with the provided Multi Function Drum Key closer or further from the drum head for Finesse "A" Position
(Fig.1-A). Make sure that the Beater Setting Stopper is flush setting or Power "B" Position setting respectively.
against the Beater Holder Link with the flat face square
against the Notch (Fig.1-B).
A B
Control Core Beater
Beater Stopper
Tip
The Beater Holder is set at the factory in the Finesse "A" Position.
Initial
Setting
Fig. 3
Tip
The Beater Setting Stopper preserves the height setting if the
beater is removed when transporting the pedal.
Fig. 5 Fig. 6
Tip
Indicator marks are provided for referencing beater angle settings
(Fig.6).
Direct Link Adjustment Duo-Deck Footboard
The Direct Link can be adjusted to provide a Heavier or a The P-3002D features Pearl's patented Duo-Deck Footboard,
Lighter feel. the world's first convertible Short / Long Footboard.
H L
Key Bolt
Footboard
Hinge
Fig. 8-B
Hinge
Fig. 8-A Fig. 10
Reattach the Hinge to the Footboard in the position shown Connecting the Drive Shaft Assembly
with two 3-Piece Screws using the provided Multi-Function Connect the ends of the Drive shaft (A) to the short
drum key or Allen wrench(3mm) (Fig.11). extensions (B) on the Main and Slave side Pedals and
tighten the Key Bolts (Fig.13 , 14).
3-Piece Screw
Drive shaft A
B
Key Bolt
Hinge
Fig. 11 Fig. 13
Key Bolt
Place the Heel Plate between the Footboard and the Hinge
(Fig.12) and attach the Heel Plate with the remaining two
3-Piece Screws using the Mutli-Function Drum Key or Allen B
wrench (3mm). Attach the Hinge to the Bottom Plate with A
the Flat Head Screws using the Multi-Function Drum Key or
Allen wrench (3mm) (Fig.12). The Hinge is now located at Drive shaft
the back of the Footboard to achieve a Long Footboard. Fig. 14
Tip
You may need to rotate the Drive Shaft Assembly to bring the
Heel Plate footboard of the Slave side (left) pedal to the proper playing height
(angle) before attaching the Drive Shaft Joints (A) to both pedals.
3-Piece Screw
Fig. 15-A
Tip
Bottom Plate
If the drive shafts are extended too far, they will separate from the
Center Connecting Tube. Reassemble them with the dots aligned
Fig. 12 as shown in Fig.15-B.
Flat Head Screw
Note
The Duo-Deck Footboard uses two
different types of screws. Make sure
to use the correct screws. Flat Head 3-Piece
Screw Screw
Spring Tension Adjustment Traction Plate / Traction Dots
The P-3002D Demon Drive Double Pedal features our The Traction Plate adjusts to a variety of grip/slide
patented Click Lock spring tension retention system. To configurations. To change the position of the Traction Dots,
increase the spring tension, disable the Click Lock by lifting use the Multi-Function Drum Key or Allen wrench (3mm) to
the lever upward, loosen the Upper Nut and tighten the remove the 3-Piece Screw beneath the footboard and
Lower Nut until the desired tension is achieved (Fig.16-A). remove the Traction Plate (Fig.19). Rearrange the Traction
To decrease spring tension, disable the Click Lock by lifting Dots to your preference and replace the Traction Plate.
the lever upward, loosen the Upper Nut and loosen the
Lower Nut until the desired tension is achieved. When the Traction Plate
desired spring tension is achieved, tighten the Upper Nut to
keep the spring tension from loosening then press the Click
Lock lever down to engage the grooves around the Lower
Nut until you feel the lever "Click" (Fig.16-B). Before playing,
make sure that both Upper and Lower Nuts are tight and the Traction Dot
Click Lock lever is in a vertical position with both sides of
the lever engaged in the grooves around the Lower Nut.
3-Piece Screw
Spring Fig. 19
Tip
Setting Examples
Upper Nut
Lower Nut
Click Lock
Fig. 17-A Fig. 17-B
Allen Wrench
Wing Bolt
Allen Screw
Adjustment Knob
Fig. 18 Fig. 20
Modular Post System Reattach the Hoop Clamp in the position shown with the two
The P-3002D features Pearl’s Modular Post System that Flat Head Screws using the provided Multi-Function Drum
allows easy conversion from one Double Pedal to two Single Key or Allen Wrench (Fig.23). Your main side pedal is ready
Pedals. to be used as a Single Pedal.
Fig. 23
Main Pedal
<d>
Spring
Assembly
<a>
<e> Bolt
Click Lock
Fig. 22 Fig. 24
Reverse the previous Optional Items (sold separately)
sequence and attach the . Control Core Wood Beater (B-300W)
Spring Assembly, Beater . Traction Rubber Grip (NP-283N/7)
Holder Link and the . Pedal Stabilizer ( PS-300 )
. NiNjA Oil ( OL-300 )
Beater to the Slave Side
Pedal. Change the
position of the Key Bolt as
shown on the Uni-Lock
Footboard Angle Cam for
easier access when
making Footboard angle
adjustments (Fig.25). Your
Slave Side Pedal is now
ready to be used as a
Single Pedal.
CAUTION
Check all Key Bolts and Allen Screws for tightness
before performance, and tighten them with the
provided Multi-Function Drum Key or Allen wrenches
as needed.
Fig. 25
Oil Fig. 26
The P-3002D features
precision NiNjA bearings for
incredible speed and
smoothness. To keep them
functioning at their maximum
speed and performance it's
recommended that you
apply genuine NiNjA Oil at
regular intervals (Fig.26).
NiNjA Oil is also ideal for
use on footboard hinges and
Direct Link bearing to
maintain "like-new"
performance (Fig.27, 28).
Fig. 28
Fig. 27
Note
For best results, always use genuine NiNjA Oil.
http : //www.pearldrum.com
Products and specifications are subject to change without notice.
Printed in China
-1504-