Professional Documents
Culture Documents
m Other features
- Wide frequency coverage Screws
<VHF>
IC-FR5300/UR-FR5300
: 136 to 174 MHz
<UHF> DC power cable DC power cable
(OPC-1784) (CAB-1149)
IC-FR6300/UR-FR6300
: 330 to 400 MHz,
400 to 470 MHz,
450 to 512 MHz,
450 to 520 MHz
- PC programmable
- 19 inch rack mount
Icom is not responsible for the destruction or damage Icom, Icom Inc. and the Icom logo are registered trademarks
of Icom Incorporated (Japan) in Japan, the United States, the
to the Icom transceiver, if the malfunction is because
United Kingdom, Germany, France, Spain, Russia, Australia,
of: New Zealand, and/or other countries.
• Force majeure, including, but not limited to, fires, All other products or brands are registered trademarks or
earthquakes, storms, floods, lightning, other natu- trademarks of their respective holders.
ral disasters, disturbances, riots, war, or radioactive
contamination.
• The use of Icom transceivers with any equipment
that is not manufactured or approved by Icom.
i
PRECAUTIONS TABLE OF CONTENTS
R WARNING HIGH VOLTAGE! NEVER touch an an- IMPORTANT................................................................ i
tenna or internal antenna connector while transmitting. EXPLICIT DEFINITIONS............................................. i
This could cause an electrical shock or RF burn. SUPPLIED ACCESSORIES....................................... i
R WARNING HIGH VOLTAGE! NEVER install the an- PRECAUTIONS.......................................................... ii
tenna at any place that person easily touch the an- SAFETY TRAINING INFORMATION........................ iii
tenna while transmitting. This could cause an electrical INFORMATIONS EN MATIÈRE DE SÉCURITÉ....... iv
shock or RF burn.
1 PANEL DESCRIPTION.............................. 1–3
R WARNING! NEVER apply AC power to the DC n Front panel......................................................... 1
power receptacle on the repeater rear panel. This D Function display............................................. 2
could cause a fire or damage the repeater. n Rear panel.......................................................... 2 1
R WARNING! NEVER apply more than 16 V DC to D Accessory connector..................................... 3
the DC power receptacle on the repeater rear panel.
2 INSTALLATION AND CONNECTIONS..... 4–6 2
This could cause a fire or damage the repeater.
n Unpacking.......................................................... 4
R WARNING! NEVER reverse the DC power cable n Selecting a location............................................ 4 3
polarity. This could cause a fire or damage the re- n Antenna connection........................................... 4
peater. n Front panel connection....................................... 5 4
R WARNING! NEVER let metal, wire or other objects n Rear panel connection....................................... 5
contact the inside of the repeater, or make incorrect n Power supply connection................................... 6 5
contact with connectors on the rear panel. This could n Mounting the repeater........................................ 6
cause an electric shock or damage the repeater. D Using the supplied handles............................ 6 6
n Fuse replacement.............................................. 6
CAUTION: DO NOT place or leave the repeater in
areas with temperatures below –30°C (–22°F) or above
D Line fuse replacement.................................... 6 7
+60°C (+140°F). Be aware that temperatures can ex-
ceed 80°C (+176°F), resulting in permanent damage
3 OPERATION.................................................. 7
n Receiving and transmitting................................. 7
8
to the repeater if left there for extended periods. D Repeater operation........................................ 7
D Base station operation................................... 7
9
CAUTION: DO NOT place or leave the repeater in ex-
cessively dusty environments. This could damage the
repeater.
4 MAINTENANCE............................................. 8 10
n Troubleshooting.................................................. 8
CAUTION: DO NOT put anything on top of the re- 11
peater. This will obstruct heat dissipation. 5 OPTIONS....................................................... 9
CAUTION: DO NOT set the repeater’s RF output
6 INFORMATION............................................ 10
12
power to more than your external linear amplifier’s
maximum input level, if you use one. Otherwise, a high
n Voice cording technology................................. 10
n FCC information............................................... 10
13
input could damage the linear amplifier.
CAUTION: DO NOT use non-Icom microphones. 14
Other manufacturer’s microphones may have differ-
ent pin assignments, and could damage the connector 15
and/or the repeater.
BE CAREFUL! The heatsink will become hot when
16
continuously operating the repeater for long periods
of time. 17
NEVER expose the repeater to rain, snow or any liq-
uids.
18
NEVER leave the repeater in an insecure place to 19
avoid use by unauthorized persons.
20
21
ii
SAFETY TRAINING INFORMATION
Your Icom radio generates RF electro- To ensure that your exposure to RF
magnetic energy during transmit electromagnetic energy is within the
mode. This radio is designed for and FCC and IC allowable limits for occu-
classified as “Occupational Use Only,” C AU TIO N pational use, always adhere to the fol-
W ARN ING
meaning it must be used only during lowing guidelines:
the course of employment by individu-
als aware of the hazards, and the ways • DO NOT operate the radio without a proper antenna
to minimize such hazards. attached, as this may damage the radio and may also
This radio is NOT intended for use by cause you to exceed FCC and IC RF exposure limits.
the “General Population” in an uncon- A proper antenna is the antenna supplied with this
trolled environment. radio by the manufacturer or an antenna specifically
authorized by the manufacturer for use with this radio.
• For compliance with FCC and IC RF Exposure Re- • DO NOT transmit for more than 50% of total radio
quirements, the transmitter antenna installation shall use time (“50% duty cycle”). Transmitting more than
comply with the following three conditions: 50% of the time can cause FCC and IC RF exposure
1. The transmitter antenna gain shall not exceed compliance requirements to be exceeded. The radio
0 dBi. is transmitting when the “TX indicator” lights red. You
2. IC-FR5300/UR-FR5300: can cause the radio to transmit by pressing the “PTT”
Transmit only when people are at least the recom- switch.
mended minimum distance of 60 centimeters away
from the properly installed antenna. This separa- Electromagnetic Interference/Compatibility
tion distance will ensure that there is sufficient dis- During transmissions, your Icom radio generates RF
tance from a properly installed externally-mounted energy that can possibly cause interference with other
antenna to satisfy the RF exposure requirements devices or systems. To avoid such interference, turn off
in the applicable RF exposure compliance stan- the radio in areas where signs are posted to do so. DO
dards. NOT operate the transmitter in areas that are sensitive
2. IC-FR6300/UR-FR6300: to electromagnetic radiation such as hospitals, aircraft,
Transmit only when people are at least the recom- and blasting sites.
mended minimum distance of 50 centimeters away
from the properly installed antenna. This separa-
tion distance will ensure that there is sufficient dis-
tance from a properly installed externally-mounted
antenna to satisfy the RF exposure requirements
in the applicable RF exposure compliance stan-
dards.
iii
INFORMATIONS EN MATIÈRE DE SÉCURITÉ
otre radio Icom produit une énergie
V fin de vous assurer que votre expo-
A
électromagnétique de radiofré- sition à une énergie électromagné-
quences (RF), en mode de transmis- tique de RF se situe dans les limites
sion. Cette radio est conçue pour un MISE EN GARDE permises par la FCC et d’IC pour une
AVERTISSEMENT
«usage professionnel seulement» et utilisation grand public, veuillez en
classée comme tel, ce qui signifie tout temps respecter les directives
qu’elle doit être utilisée uniquement suivantes:
dans le cadre d’un travail par des
personnes conscientes des dangers • NE PAS faire fonctionner la radio sans qu’une
et des mesures visant à minimiser antenne appropriée y soit fixée, car ceci risque
ces dangers. Elle N’EST PAS conçue
pour une «utilisation grand public»,
d’endommager la radio et causer une exposition
supérieure aux limites établies par la FCC et d’IC.
1
d a n s u n e nv i ro n n e m e n t n o n
contrôlé.
L’antenne appropriée est celle qui est fournie avec
cette radio par le fabricant ou une antenne spécia-
2
lement autorisée par le fabricant pour être utilisée
• Afin de satisfaire aux exigences de la FCC et d’IC avec cette radio. 3
en matière d’exposition aux RF, il est nécessaire que • NE PAS émettre pendant plus de 50% du temps
l’antenne soit installée conformément aux trois condi- total d’utilisation de l’appareil («50% du facteur 4
tions suivantes: d’utilisation»). Émettre pendant plus de 50% du
1. Le gain de l’antenne du radio émetteur ne doit pas temps total d’utilisation peut causer une exposition 5
dépasser 0 dBi. aux RF supérieure aux limites établies par la FCC
2. IC-FR5300/UR-FR5300: et d’IC. Lorsque le voyant DEL rouge s’allume, 6
Transmettre que lorsque les gens sont au moins cette radio est en train d’émettre. La radio émettra
la distance minimale recommandée de 60 cen- si vous appuyez sur le bouton du microphone. 7
timètres de l'antenne est correctement installé.
Cette distance de sécurité assurera que les per-
sonnes soient placées suffisamment loin d’une
Interférence électromagnétique et compatibilité
En mode de transmission, votre radio Icom produit de
8
antenne correctement fixée à l’extérieur pour sat-
isfaire aux exigences en matière d’exposition aux
l’énergie de RF qui peut provoquer des interférences
avec d’autres appareils ou systèmes. Pour éviter de
9
RF, en vertu des normes de conformité applica-
bles.
telles interférences, mettez la radio hors tension dans
les secteurs où une signalisation l’exige. NE PAS faire
10
2. IC-FR6300/UR-FR6300: fonctionner l’émetteur dans des secteurs sensibles au
Transmettre que lorsque les gens sont au moins rayonnement électromagnétique tels que les hôpitaux, 11
la distance minimale recommandée de 50 cen- les aéronefs et les sites de dynamitage.
timètres de l'antenne est correctement installé. 12
Cette distance de sécurité assurera que les per-
sonnes soient placées suffisamment loin d’une 13
antenne correctement fixée à l’extérieur pour satis-
faire aux exigences en matière d’exposition aux RF, 14
en vertu des normes de conformité applicables.
15
16
17
18
19
20
21
iv
1 PANEL DESCRIPTION
n Front panel
r
t
Function
q w display e y
P0 P1 P2 P3 P4
o i u
q INTERNAL SPEAKER u MICROPHONE CONNECTOR [MIC]
Outputs the received audio. This 8-pin modular jack accepts an optional micro-
phone.
w VOLUME CONTROL [VOLUME] (p. 7)
KEEP the [MIC] connector cover attached to the
Adjusts the audio output level.
repeater when an optional microphone is not
used.
e SELECTOR DIAL [SELECT]
Rotate to adjust the squelch threshold level, select q +8 V DC output (Max. 15 mA)
the operating channel. (Depending on the preset- w Output port for PC programming
ting.) q i e NC
r M PTT (Input port for TX control)
r POWER INDICATOR [POWER] t Microphone ground
➥ Lights green at ‘A’ module's indicator while the y Microphone input
repeater power is turned ON. (Front panel view) u Ground
i Input port for PC programming
When a channel extension module is installed:
➥ Lights green at the selected module indicator i POWER SWITCH [POWER]
(‘A’ or ‘B’) while the repeater power is turned ➥ Push to turn ON the repeater power.
ON. ➥ H old down for 3 seconds to turn OFF the re-
➥ Lights orange at the un-selected module indica- peater power.
tor (‘A’ or ‘B’) while the repeater power is turned
ON. When a channel extension module is installed:
➥ While the repeater power is turned ON, push
t TRANSMIT INDICATOR [TX] to select the desired module to operate the re-
Lights red while transmitting. peater as the base station.
• The power indicator of the selected module unit
y BUSY INDICATOR [BUSY] lights green.
Lights green while receiving a signal or when the
noise squelch is open. o DEALER-PROGRAMMABLE KEYS
Desired functions can be independently preset by
About [PWR], [TX] and [BUSY] indicators: your dealer.
‘A’ and ‘B’ modules indicators are usable for these Ask your dealer for details.
• Because these keys are programmable, the functions
indications. ‘A’ module's indicator corresponds to
are unique to each unit.
the original module, and ‘B’ module's indicator cor-
responds to an extended module.
1
PANEL DESCRIPTION 1
D Function display
q w e r
ICOM Inc. t
y
2
1 PANEL DESCRIPTION
D Accessory connector
!4 @5
q !3
* The desired function can be assigned using the optional CS-FR5300 cloning software. Ask your dealer for details.
3
INSTALLATION AND CONNECTIONS 2
n Unpacking n Antenna connection
After unpacking, immediately report any damage to For radio communications, the antenna is a critical
the delivering carrier or dealer. Keep the shipping car- component, along with output power and sensitivity.
tons. Select antenna(s), such as a well-matched 50 ø an-
tenna, and feedline. 1.5:1 or better of Voltage Stand-
For a description and a diagram of accessory equip- ing Wave Ratio (VSWR) is recommended for the de-
ment included with the repeater, see ‘SUPPLIED AC- sired band. Of course, the transmission line should be
CESSORIES’ on page i of this manual. a coaxial cable.
4
2 INSTALLATION AND CONNECTIONS
P0 P1 P2 P3 P4
Supplied
DC power
1A cable (CAB-1149)* 20 A
fuses Red fuses
P0
P1
P2
1
P3
P4
Screw
2
Handle
Spacer
3
w The completed installation should look like the illus-
4
tration below.
5
6
P0
P1
P2
P3
P4
7
8
9
n Fuse replacement 10
If a fuse blows, or the repeater stops functioning, find CAUTION: DO NOT replace the fuse with the DC
the source of the problem, repair it and then replace power cable connected to the repeater. Disconnect 11
the damaged fuse with a new rated one. the cable to prevent electric shock and/or equip-
ment damage. 12
D Line fuse replacement 13
14
15
Fuse rating: 20 A
16
USE only a 20 A fuse.
17
18
19
20
21
Fuse rating: 1 A
3 OPERATION
Transmitting
q Take the microphone off hook.
w Wait for the channel to become clear.
e Hold down [PTT] to transmit, then speak into the
microphone at your normal voice level.
r Release [PTT] to receive.
IMPORTANT:
To maximize the audio quality of the transmitted
signal:
1. Pause briefly after pushing [PTT].
2. Hold the microphone 5 to 10 cm (2 to 4 inch)
from your mouth, then speak at your normal
voice level.
7
MAINTENANCE 4
n Troubleshooting
The following chart is designed to help you correct If you are unable to locate the cause of a problem
problems that are not equipment malfunctions. or solve it through the use of this chart, contact your
nearest Icom Dealer or Service Center.
8
5 OPTIONS
9
INFORMATION 6
n Voice coding technology
The AMBE+2™ voice coding Technology embodied in
this product is protected by intellectual property rights
including patent rights, copyrights and trade secrets
of Digital Voice Systems, Inc. This voice coding Tech-
nology is licensed solely for use within this Communi-
cations Equipment.
The user of this Technology is explicitly prohibited
from attempting to extract, remove, decompile, re-
verse engineer, or disassemble the Object Code, or in
any other way convert the Object Code into a human-
readable form. U.S. Patent Nos.
#8,595,002, #8,359,197, #8,315,860, #8,200,497, 1
#7,970,606, and #6,912,495 B2.
2
n FCC information 3
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to 4
part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful in- 5
terference in a residential installation. This equipment
generates, uses and can radiate radio frequency en-
ergy and, if not installed and used in accordance with
6
the instructions, may cause harmful interference to
radio communications. However, there is no guaran-
7
tee that interference will not occur in a particular in-
stallation. If this equipment does cause harmful inter-
8
ference to radio or television reception, which can be
determined by turning the equipment off and on, the 9
user is encouraged to try to correct the interference
by one or more of the following measures: 10
• Reorient or relocate the receiving antenna. 11
• Increase the separation between the equipment and
receiver. 12
• Connect the equipment into an outlet on a circuit dif-
ferent from that to which the receiver is connected. 13
• Consult the dealer or an experienced radio/TV tech-
nician for help. 14
CAUTION: Changes or modifications to this repeater, not
15
expressly approved by Icom Inc., could void your authority
to operate this repeater under FCC regulations. 16
17
18
19
20
21
10
A?????-1EX
Printed in Japan
© 2020 Icom Inc. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan