Professional Documents
Culture Documents
Assa Abloy Surface Mounted Door Closers Catalogue
Assa Abloy Surface Mounted Door Closers Catalogue
www.lockweb.com.au
Contents
Lockwood Premium Rack and Pinion Range with Fully Formed Cover
726 Series Door Closer 726SR Series Door Closer 724 Series Door Closer 724SR Series Door Closer
page 26 page 28 page 30 page 32
314
Arm B
119
Screw
Nut
Arm A Link arm
2657 Series Door Closer 2024 Series Door Closer Standard Hold-Open Arm Standard Drop Plates
page 14 page 34 page 37 page 38
Contents
page 39
Designed and manufactured to exacting standards. hold or close the door against this pressure must
These world recognised standards ensure the be considered along with the ability of the user to
highest possible quality, efficiency and reliable exert the force necessary to push or pull the door
performance. open. The location of door furniture will influence
the leverage available to the person opening the
All models (except hold-open) are tested and
door.
approved on fire doors in accordance with The Lockwood 25 Year
Australian Standard AS1905:1:2005 Fire Resistant Mechanical Warranty
Doorsets. About Lockwood
New multifunctional designs offer the specifier, Lockwood is the leading brand in the Australian Our belief that we manufacture the finest premium
stockist or the installer outstanding versatility and locking industry. With an established reputation products available in today’s market place is
low inventory levels. for high quality products, this iconic brand backed by the Lockwood 25 Year Mechanical
provides a wide range of locking solutions to Warranty, ensuring that Lockwood continues to
Effective door installation requires that the door residential housing, commercial building and keep Australians safe by delivering security and
and frame be of sufficient strength or reinforced to industrial application markets. Lockwood is peace of mind.
ensure secure anchorage of the door closer unit. supported by an extensive distribution and after-
For warranty terms and conditions, please visit
A door fitted with a door closer must be hung sales support network. Our customers include
www.lockweb.com.au or call 1300WARRANTY
on good quality, aligned hinges so it swings freely retailers, architects, trade and industrial personnel,
without bias in both directions. locksmiths and security dealers.
Selection of door closer size is judged in two ways. Fire doors which open into a pressurised stairwell Parallel Arm Mounting
must meet the following criteria: Approximately 20 % power loss
1. Does the door closer have the strength to
effectively close the door against unexpected air • The door must close against a pressure
pressures? differential between the air conditioned floor
Slide Rail Mounting
area and non-air conditioned stairwell;
2. Is the door closer oversized for the application Approximately 30 % power loss
and therefore affecting the ease of operation? • The door must latch securely every time it closes;
Efficiency of the door closer also has a major • The door must be able to be opened with a
Power Selection Chart
bearing on ease of operation. For optimum force not exceeding 110N when the stairwell is
This chart below will be most useful in selecting
performance it is essential that a highly efficient pressurised; and
the correct door closer. Simply identify the
door closer of a correct size is selected.
• The door must be protected from damage when dimensions of the appropriate door and select the
The use of spring strength adjustability, which it is opened by means of a back check action recommended door closer.
allows fine tuning of strength on site, has simplified which is built into the door closer.
The chart is intended as a guide only and as such
this task but not removed all of the guesswork.
the following variations should be taken into
With more architects and engineers becoming
account when making your selection:
conscious of the problems caused by incorrect Note
selection of door closer strength, it has become • Environmental factors such as the effect of wind
the responsibility of manufacturers to provide • Always round up to the next door width
or air conditioning pressures.
better technical information, such as closing (i.e. For 870mm door use 950mm).
torque and efficiency of their products. • An unsheltered external door is a door on which
• If parallel arm installation, then use next
prevailing wind gusts will directly produce a “sail
The following chart has been produced to door width (i.e. For 830mm door use 950mm).
area” effect.
cover most conditions. If you have an unusual
• For internal doors deduct 200mm from actual
application which you feel requires special • A
sheltered external door is a doorway which is
door width (i.e. For 1250mm internal door use
consideration, please forward all relevant protected by a wind break or wall which acts as a
1050mm).
information to your local office and we will be barrier against direct wind gusts.
happy to advise the best door control for your • This chart is based on normal climatic conditions
application. (i.e. Pressure differential of 30Pa or wind of 15
knots).
Fire doors and pressurised stairwells pose
significant challenges in ensuring closing and • If more severe conditions are expected then use
latching of fire doors. The problems are created by the next door width or contact customer service
differential air pressures resulting from for more information (refer back page).
air conditioning systems on either side of the door.
• When specifying parallel arm and slide rail
To achieve complete fire safety, fire doors must
functions, allowance should be made for the
latch securely at all times. If this performance is
following power loss:
not achieved the stairwell may be unsafe, and
in the event of fire, loss of life and property may
occur. Correct selection of door hardware is of
paramount importance in ensuring that the
appropriate operating standards are met.
Recommended Door Width Door Weight (kg) Max Closer Power Size Closing Torque (Nm)
750mm 20 1 9 - <13
850mm 40 2 13 - <18
950mm 60 3 18 - <26
1100mm 80 4 26 - <37
1250mm 100 5 37 - <54
1400mm 120 6 54 - <87
1600mm 160 7 87 - <140
500 mm
69 mm
(Depth: 63 mm)
308 mm
Movement Curve
Opening
Torque (Nm) Closing
40
30
20
10
Note: M
ovement curve represents approximate forces required to operate a size 1 door closer.
The illustration is an approximation based on one set of parameters. Any change to these
parameters will result in a variation of performance.
Recommended Door Width Door Weight (kg) Max Closer Power Size Closing Torque (Nm)
750mm 20 1 9 - <13
850mm 40 2 13 - <18
950mm 60 3 18 - <26
1100mm 80 4 26 - <37
1250mm 100 5 37 - <54
1400mm 120 6 54 - <87
1600mm 160 7 87 - <140
max 91 506
max10
10 91 506
Pull Side - Standard Mounting
110-124
110-124
23
23
Non hold-open permits door opening to
170°, and 160° when opening damper is
used. When hold-open device is installed, Max. framedepth
Max. frame depth 87
87
the opening angle (hold-open) can be set
to a maximum of 120°.
23
23
110-124
max
max10
10 91
91 506
506
Push Side - Over-Door
110-124
110-124
23
Mounting
87
87
Pull Side - Door Mounting
110-124
110-124
23
max
max 3
23
3
Non hold-open permits door opening to
170°, and 160° when opening damper is
used. When hold-open device is installed, Max.
Max.frame depth
frame depth 91
91 506
506
the opening angle (hold-open) can be set
to a minimum of 120°.
1250 35
15 25
11 9
ø55
ø10
Part Number 2616-104SIL 242.5 242.5 10.5
110-124
23
110-124
15 25 max 10
90º
30
5
11 11 99
Allows the side rail to be installed below
30 506
the door jamb. Required155 when the14 face
6 of
23
182
15
the door jamb exceeds 25 mm from the
726-109 44
face of the door in the closed position. 87 50
Max. frame depth
87 87
303
110-124
303
Ø 6.5 110-124
88 160
Mounting Plate 88 160
73 160 4
73 63 160
23
Part Number 2616-180SIL 100 4
63 100
Ø 11
90º
Ø 6.5
Ø 11
90º
16 11 16
22
22
44 91 506
45
45
66
44
45
45
66
M6
22
the top rail, at the same time concealing
M6
22
the back of the closer. Max. frame depth
100 25 135
100 25 282.6 135
282.6
Adjustment Adjustment
Adjusting the Arm Height
max 14
A
170° 70°
c
180° 70°
170° 7° The arm height can be adjusted (by a maximum of 14mm)
Back check (BC) 7° 0° by moving the grooved spindle in a vertical direction.
Delayed
closing (DC)
500 mm
63 mm
(Depth: 63 mm)
267 mm
Movement Curve
Opening
Torque (Nm) Closing
40
30
20
10
Note: M
ovement curve represents approximate forces required to operate a size 1 door closer.
The illustration is an approximation based on one set of parameters. Any change to these
parameters will result in a variation of performance.
Recommended Door Width Door Weight (kg) Max Closer Power Size Closing Torque (Nm)
750mm 20 1 9 - <13
850mm 40 2 13 - <18
950mm 60 3 18 - <26
1100mm 80 4 26 - <37
1250mm 100 5 37 - <54
1400mm 120 6 54 - <87
1600mm 160 7 87 - <140
110-124
110-124
23
Non hold-open permits door opening to
170°, and 160° when opening damper is
used. When hold-open device is installed,
Max. framedepth
Max. frame depth 87
87
the opening angle (hold-open) can be set
to a maximum of 120°.
23
23
110-124
91 506
Push Side - Over-Door max
max 10
10 91 506
110-124
Mounting
23
110-124
23
87
87
Pull Side - Door Mounting
110-124
110-124
23
max
max33
23
275 250 70
4
726-105
Angle Plate
532 35 91 10.5506 91
ø55
ø10
35 242.5
242.5 242.5
242.5 10.5
Part Number 2616-104SIL
15 25
110-124
23
110-124
max 10
90º
30
30
5
11
11 99
Allows the side rail to be installed below
30 506
506
the door jamb.155
Required when 14 the
6 face of
23
182
23
15
15
the door jamb exceeds 25mm from the 4
26-109
face of the door in the closed position. 87 50
Max. frame depth
87 87
110-124
110-124
Mounting Plate
23
Part Number 2615-180SIL
max 3
91 506 91
For use on glazed doors with small top rail,
this plate allows the closer to project below
the top rail, at the same time concealing Max. frame depth
the back of the closer to enhance the
appearance as seen through the glass.
Adjustment Adjustment
Adjusting the Arm Height
max 14
A
170° 70°
c
180° 70°
170° 7° The arm height can be adjusted (by a maximum of 14 mm) by moving the
Back check (BC) 7° 0° grooved spindle in a vertical direction.
Delayed
closing (DC)
The Lockwood 2657 Heavy Duty Series
is suitable for use on internal and Specifications
external doors and is an ideal solution
Power EN adjustable 5 to 7
for extremely heavy doors. Maximum
door weight 160kg and door leaf Back check (BC) Adjustable
width 1600mm with standard arm Non-handed
Handing
installation. Suitable for left or right hand doors
Cover Fully formed metal
Die-cast aluminium body manufactured
Materials
from high performance silicon alloy
Mechanism Rack and pinion design
Mounting Regular and over-door mounting
Separate adjusting valves for closing and latching speed.
Valves
Two pressure relief valves to protect against abuse.
Ordering Information
2657SIL Silver
69 mm
63 mm
m
306 m
Slide push side
45
45
32
90-104
63
90-104
90-104
Standard arm pull side Standard arm push side above door
Adjustment
Lockwood Door Closers are non-handed, therefore final Approved on fire door assemblies up to 4 hours,
assemblies are suitable for clockwise or anticlockwise in accordance with Australian Standards AS1905
opening doors. Part 1 – Fire Resistant Doors 2005.
Back check is a standard feature on all models in this series. The hold-open device is located on the link arm and is
Back check cushions or slows the opening movement of the activated by a cam. The position of the cam is adjustable to
door prior to reaching the final open position. suit the desired hold-open position up to 150º.
Back check intensity is adjustable to allow for door size, The operation of the hold-open device does not limit the
door weight and closing power. It is mandatory on all fire angle to which the door may be opened, as the door may
doors. be pushed past the hold-open position without effecting
its operation.
Door Stops
A firm push or pull on the door will release the
Floor or wall mounted door stops should be fitted to
hold-open device.
prevent possible damage to the door unit or surrounds
where a door may be subject to violent opening; to stop a Slide Rail Hold-Open
door from being forced past the position where the arms
Hold-open is a standard feature for all slide arm door
are fully extended; or to stop a door at a specific position to
closers. It can be adjusted or disabled at any angle of the
clear feature walls, glass panels, furniture, etc.
open arc.
Delayed Action Independently Adjustable
Note: Hold open option is not approved on any fire door.
Hydraulic Valves
The delayed action is an independent valve and can Back check.
either be adjusted as part of the closing sequence or Pinion Needle Bearings
Latching speed.
independently adjusted for delayed action. Closing speed.
High grade pinion with precision
needle bearings increases efficiency
Such doors are particularly suitable for use by the disabled,
and minimises wear ensuring a
the aged and people with prams or trolleys. prolonged operational life.
Sequence Selectors
When a pair of rebated doors are fitted with door closers it Spring
is essential that the doors close in their correct sequence. Highest grade silicon chrome
This closing sequence is achieved by the installation of a steel springs provide smooth
action and long life.
sequence selector.
Materials
Standard Features
7726DA 7714 DA
Primary Lock 726 724 2024
Premium Premium
Materials
Extruded Aluminium body with hard
3 3 3 3
anodised coating
Alloy Steel Rack and Pinion Mechanism 3 3 3 3 3
Clip-on Cover 3 3
Power Adjustment
Adjustable Power 3 3 3 3
Power Size
Power Size 1 3
Power Size 2 3 3 3 3 3
Power Size 3 3 3 3 3 3
Power Size 4 3 3 3 3 3
Power Size 5 3 3
Power Size 6 3 3
Features
Back Check 3 3 3 3 3
Delayed Action 3 3
Non-Handed 3 3 3 3 3
Overload Protection 3 3 3 3 3
Standard Arm 3 3 3 3 3
Slide Arm 3 3 3 3
Standard Hold-Open 3 3 3 3 3
Fire Rated 3 3 3 3 3
Finishes
Satin Stainless Steel 3 3 3 3
Silver 3 3 3 3 3
Gold 3 3 3 3
Black 3 3 3 3
Ordering Information
Model Part Numbers Finishes
7726DASSS Satin Stainless Steel
Standard Arm 7726DASIL Silver
7726DABLK Black
7726HDASSS Satin Stainless Steel
Hold-Open
7726HDASIL Silver
282
7726DA Standard Arm 282
282
32
32
32
55
7726DA Non hold-open 266
266 91
91 55
266 91 55
7726HDA Hold-open
61
61 61
7726HDA Hold-open
266 266
266 55
55 55
19 1919
Closer installed on push side of door. This
Standard arm pull side Standard arm push side above door Parallel arm push side
mounting position permits opening of 180°.
Slide push side above door
Slide push side
40
7726DA Over Door Mounting 266
266
266 91
91
91
282
282 282 40 40
81 81
81
Ordering Information
Model Part Numbers Finishes
7726SRDASSS Satin Stainless Steel
Slide Arm 7726SRDASIL Silver
7726SRDABLK Black
NOTE: Slide Rail installation may result in a spring strength loss of up to 30% in most cases. Please consider the application and usage of the door prior to selecting the appropriate door control.
Part Numbers
126 126
126
7726SRDA
266 266
266 106 106
106
55
55 55
Part Numbers
7726SRDA
124 124
124
55
55 55
266 266
266
79
79
79
Part Numbers
45
45
45
7726SRDA
84 84
84
Ordering Information
Model Part Numbers Finishes
7714DASSS Satin Stainless Steel
Standard Arm 7714DASIL Silver
7714DABLK Black
7714HDASSS Satin Stainless Steel
Hold-Open 7714HDASIL Silver
282
7714DA Standard Arm 282
282
32
32
32
55
7714DA Non hold-open 266
266 91
91 55
266 91 55
7714HDA Hold-open
61
61 61
Part Numbers Description
7714HDA Hold-open
266 266
266 55
55 55
19 19
19
Closer installed on push side of door. This
Standard arm pull side Standard arm push side above door Parallel arm push side
mounting position permits opening of 180°.
Slide push side above door
Slide push side
81 81
81
Product Details
Model Part Numbers Finishes
7714SRDASSS Satin Stainless Steel
Slide Arm 7714SRDASIL Silver
7714SRDABLK Black
NOTE: Slide Rail installation may result in a spring strength loss of up to 30% in most cases. Please consider the application and usage of the door prior to selecting the appropriate door control.
546 546
546 89 89
89
Part Numbers
266
266
266 106 106
106 55
55 55
7714SRDA
546
546
546 124
124
124
7714SRDA 55
55 55
266 266
266
27
27 27
50
7714SRDA Slide Arm Over Door 266
266
266 86
86
86 50 50
Part Numbers 45 45
45
7714SRDA 84 84
84
Ordering Information
Model Part Numbers Finishes
726SSS Satin Stainless Steel
726PSS Polished Stainless Steel
Standard Arm
726SIL Silver
726BLK Black
726HSSS Satin Stainless Steel
Hold-Open 726HPSS Polished Stainless Steel
726HSIL Silver
282
282
282
81 81
55
255
255 91
91 55
Closer installed on pull side of door. This Standard arm pull side S
61
61 61
726H Hold-open
255 255
255 55 55 55
19
Standard arm pull side
1919
Standard arm push side above door Parallel arm push side
Closer installed on push side of door. This
mounting position permits opening of 180°.
Slide push side above door
Slide push side
40
726 Over Door Mounting 255 91 282
255 255 91 91 282 282 40 40
81 81
81
Ordering Information
Model Part Numbers Finishes
726SRSSS Satin Stainless Steel
726SRPSS Polished Stainless Steel
Slide Arm 726SRSIL Silver
726SRGLD Gold
726SRBLK Black
NOTE: Slide Rail installation may result in a spring strength loss of up to 30% in most cases. Please consider the application and usage of the door prior to selecting the appropriate door control.
546 546
546 89 89
89
Part Numbers
266 266
266 106 106
106 55
55 55
726SR
Part Numbers
124 124
124
726SR
266 55
55 55
266 266
27
27 27
50
726SR Slide Arm Over Door 266
266
266 86
86
86 50 50
Part Numbers 45 45
45
726SR 84 84
84
Ordering Information
Model Part Number Finish
724SSS Satin Stainless Steel
724PSS Polished Stainless Steel
Standard Arm
724SIL Silver
724BLK Black
724HSSS Satin Stainless Steel
724HPSS Polished Stainless Steel
Hold-Open
724HSIL Silver
Slid
Slide push side
69
69
724 Non hold-open
40
724H Hold-open 40
235
235 91
91
449
449
724 Parallel Arm 61
61
Standard arm pull side Standard arm push side above door Parallel arm push side
Closer installed on push side of door. This
mounting position permits opening of 180°.
724H Hold-open
Closer installed on push side of door and Standard a rm pull side Standard a rm push side ab ove door P aralle
top rail where conditions do not allow
parallel mounting. This mounting position
permits opening of 180°.
Ordering Information
Model Part Number Finish
724SRSSS Satin Stainless Steel
724SRPSS Polished Stainless Steel
Slide Arm 724SRSIL Silver
724SRGLD Gold
724SRBLK Black
NOTE: Slide Rail installation may result in a spring strength loss of up to 30% in most cases. Please consider the application and usage of the door prior to selecting the appropriate door control.
Part Numbers 41
41
41
81 81
81
724SR
40
40 40
235 235
235 128 128
128
Part Numbers
724SR
40 40
Closer installed on push side of door. This 235 235
235 38 38
40
38
mounting position permits opening of 115°.
64
64
64
Part Numbers
47 47
47
724SR
546 546
546 47 47
47
Closer installed on push side of door and top
rail where conditions do not allow parallel
mounting. This mounting position permits
opening of 115°.
Ordering Information
Model Part Number Finish
Standard Arm 2024SIL Silver
Standard Arm
2024BCSIL Silver
with BC
Hold open 2024HSIL Silver
Offset arm 2024BCOPSIL Silver
183
183 49.5
49.5
Part Numbers 19 19 68
2
2024SIL 60
60 203 203
2024BCSIL 219
219 48.5
2024HSIL
183 49.5
221 Standard
2
60 203
219 48.5
48.5
221 Standard
175
175
65
65
Part Numbers 65
65
2024SIL 19
19
68
2
2024BCSIL
116
116 203203
2024HSIL 219
219 48.5
Closer
65 installed on push side of door.
Standard mounting position permits door
parallel
opening of 180°. If hold-open is installed
the hold-open range is 80° to 165°.
1
68
68
2
203
219
48.5
48.5
121 parallel
121 parallel
Lockwood Product Catalogue | Surface Mounted Door Closers
1300 LOCK UP (1300 562 587) lockweb.com.au 35
2024 Series Door Closer
219
219 48.5
68
Part Numbers
19 19
22 22
2024SIL
2024BCSIL
183
183 49.5
49.5
2024HSIL
221 overdoor
37.5
37.5
2024 Metal Door Mounting
Part Numbers
221 overdoor 60
60
1
19
19
68
2024BCPOSIL 2
116
116 203203
219
219 48.5
Closer installed on push side of door to suit
doorstop of 15 mm. Standard mounting
position permits door opening of 180°. If
hold-open
37.5 is installed the hold-open range
is 90° to 165°.
68
521
68
2
203
219 48.5
48.5
521
Arm B
7714/724 Hold Open Arm
Screw
Part Number SP7714-224SIL
Nut
Arm A Link arm
Delayed Action A
The delayed action is an independent valve
and can either be adjusted as part of the closing
sequence or independently adjusted for
delayed action.
314
314
7726/7714 Drop Plate
Part Number 7726-180SIL
119
119
251
251
7724 Drop Plate
Part Number 7724-180SIL
119
119
303
Mounting Pate 88 160
73 160 4
Part Number 2616-180SIL 63 100
Ø 6.5
Ø 11
90º
16 11 16
22
44
45
45
66
Mounting Plate
Part Number 2615-180SIL
Part Numbers
2636FS-SIL
2636FS-A189
max.13
38
43 15
68,5
103
100
2636FS-SIL
43
15
100
38
2636FS-A189 213,5 100
Ø8 (24 V DC) 90
Required surface area for door leaf
installation on hinge side. Left handed
shown in diagram. Right handed is the
reverse
213,5 100
Overhead Transom
Ø8 (24 V DC)
Mount Pull Side 64,5 38
43
40
Part Numbers
11
2636FS-SIL 110 485
2636FS-A189
15
Part Numbers
2636FS-SIL
25
110 485
2636FS-A189
info.nz@assaabloy.com
Telephone +64 9415 7111
assaabloy.co.nz
Disclaimer
Whilst every effort has been made to ensure that the information (including product images and drawings) contained in this brochure is accurate at the time of publication,
MC11400
ASSA ABLOY Australia Pty Limited (“ASSA ABLOY”) recommends that you consult ASSA ABLOY or its agents prior to placing an order to ascertain current information on specific products,
as ASSA ABLOY reserves the right to make changes without notice. ASSA ABLOY will not be liable for any injury, loss or damage whatsoever, arising from any errors or omissions in the
information contained in the brochure or arising from the use or application of the information contained herein. © 2021 copyright by ASSA ABLOY All rights reserved
ASSA ABLOY Australia Pty Limited ABN 90 086 451 907 ©2021_07