Professional Documents
Culture Documents
Visual Testing Qustion Level 3
Visual Testing Qustion Level 3
5) Which of the following is Black body 11) A Bow of a pump shaft is best Checked by
a) Tungsten filament @3000° K a) Placing it on a precise V-block
b) A coiled tungsten filament @3000° K b) Mounting the shaft in the original machining
c) Both a & b centers
d) None of the above c) Preparing new centres and loading it between the
head stock and tailstock of long-bed lathe
6) As the distance of inspection is increased, the resolving d) Any convention manner taking in to account the
power of human eye existing facility.
a) Increases
b) Decreases 12) A loose-fit between stem to disk connections in a Globe
c) Same valve can lead to
d) None of the Above. a) Erratic operation
b) Excessive noise
c) Accelerated wear of seat
d) All the above
13) For a New Tubular part, used in Oil field type of 18) A high performance video system has the following
Inspection to be carried out specifications. Calculate the Resolution
14) The evaluation of test lamp against an un calibrated 19) Compare to Fibrescope, Which is not an advantage of
Light source is called Videoscope
d) Dissolving of aluminum
38) 7X magnifier used in inspection will give
34) The instrument used to compare the surface a) High magnification, high depth of field,
roughness is
low resolving power
a) Profile gauge
b) High magnification, large field of view,
b) Reflecto meter
high resolving power
c) Surface comparator
c) Low magnification, narrow field of view,
b) Heat bonding 39) Out of the films given below, which one is the
fastest film? (Films are in ASA values)
c) Gas welding
b) 100 ASA
c) Coating a) 80grit
d) Low magnification, large field of view, low 56) Technique or science is comparing & studying the
resolving power structure of metal is:
a) Fluidity b) Metallography
b) Void c) Photoconduction
d) Cracks
58) How many Duplicate replicas requires in replication 62) Mention a BASIC JOINT of Weld configuration
a) 1 a) Single- V
b) 2 b) Single –U
c) 3 c) Single – J
59) Mention the Surface Highlighting Technique for a crack 63) A Convex fillet weld of size 6mm is welded instead of
consistent with Impact damage on the surface of a 3mm.If the convexity is ignored, the unnecessary
Composite material? percentage increase in filler metal consumption is
d) Snubber d) 400
e) None of the above 64) Penetrants are classified by the method used to remove
the excess penetrant from the part. The four methods are
60) The image formation in eye is by iris and retina listed below:
blue this image formed by
a) Method A - Water Washable
a) Receives converted
b) Method B - Post Emulsifiable, Lipophilic
b) Blues
c) Method C - Solvent Removable
c) Photo Cathode
d) Method D - Post Emulsifiable, Hydrophilic
d) CRT exciter
e) All the above are four methods
61) In general, the cause of underbead cracking in steel
weldments is largely due to 65) In a Square Groove Weld Butt Joint
a) Preheating the weldments prior to welding a) Joint & Root Penetration both are equal
67) For Concave Fillet weld the size of weld is 71) In a visual inspection area of greater Luminance is 100
Cd/m2, The Luminance contrast is
a) Equal to Leg
a) 0.25
b) Larger than leg
b) 0.20
c) Smaller than leg
c) 2.50
d) No related to leg
d) 2.0
68) To avoid inspector eye fatigue and to enhance the
probability of detection due to size, the maximum 72) The lighting to be used in Vision acuity test is
recommended luminance ratio between tasks and
adjacent lighter surroundings is a) Fluorescent
a) 3:1 b) Incandescent
b) 1:3 c) Mercury
69) The vision provides ability to distinguish the depth a) Incident angle
between object is
b) Visual angle
a) Near vision
c) Refractive angle
b) Far vision
d) None of the above
c) Stereoscopic vision
74) The Magnification of a Compound microscope
d) None of the Above
a) M = Mo + Me
b) M = Mo x Me
c) M = Mo x (1 + Me)
75) A Wide FOV (Field of view )produces 79) Black colour may be considered as any colour that is
highest in
a) High magnification and shorter DOF
a) Hue
b) High magnification and greater DOF
b) Saturation
c) Low magnification and Greater DOF
c) Value
d) Low magnification and Shorter DOF
d) All the above
78) The output of a radiographic film illuminator screen is b) Be capable of reading standard J-1 letter on
expressed in standard Jaeger test charts for near distance
acuity
a) Luminous intensity
c) Be capable of reading standard J-1 letter on
b) Luminance standard Jaeger test charts for Far distance
acuity
c) Illuminance
d) All the above
d) Luminous Flux
82) Which type of camera would be preferred choice for 87) What term is used to determine acuity measurements
operation within high radiation environment.? with a moving target?
a) Direct ,Remote, Translusecent 90) Which of the following most closely a grey body by
exhibiting very nearly uniform emissvity?
b) Robotic, Steroscopic
a) Electric arc from TIG gun
c) Microscopic, Telescopic test b) A carbon filament in the visible region
c) Tungsten filament
d) Both B & C d) Xenon short arc search light
85) What is the maximum angle from normal for acrrying out
visual inspection? 91) Which of the following laws state that light flux striking
a) 30 degrees a surface at angles other than normal is
b) 45 degrees distributed over a greater area?
c) 60 degrees
d) 80 degrees a) Lambert cosine law
b) Inverse square law
86) As the human eye becomes older which region of c) Cosine cubed law
wavelength becomes increasingly more absorbed? d) Boyles law
a) Blue
b) Green
c) Yellow
d) Red
92) Which of the following equations shows the lambert
cosine law?
a) E = (I cos3°) / a 2
10) VT-1 : Condition of a Component
b) E = I / d2
c) E = (I / d2) cos ° VT-2 : Location of evidence of Leakage
d) E = (I2 / d) cos
VT-3 : Genral Mechanical and Structural
Condition of Supports.
5) Magnification Increases Working Distance reduces and 14) Resolving Power: The quantitative ability of a person to
Resolving Power Increases. resolve objects is determined in a practical manner from
distance of the object to eye and angle of separation of two
6) Wide FOV gives Reduced Magnification and Increased points that can be resolved by eye .
Depth of Field.
15) For the Average eye,the minimal resolvable angular
7) Accuracy is twice the time of resolution separation of two points on an object is about 1 minute of
arc 1/60th of 1°
8) Additve Colors : Green,Red,Blue
16) This means about 12” (300mm)from test surface, the best
SubtractiveColors :Magentha,Cyan,Yellow resolution to be expected is 0.0035”(0.09mm)At 24”
(600mm) resolution 0.007”(0.18mm)
9) Linear Magnification is proportionally Changes with
Working Distance and inversely proportional to Objective Direct Visual test are best performed at a distance of
distance.
10-24”(250-600)
3) Visual inspection of a component shows signs of
beach marks(Clam Shell appearance) and bright
17) Eye examination for Near and far vision are
white brittle fracture and it is classified as
usually carried out at a distance of 15”@ 6m
a) Fatigue
18) Vision acuity are recommendd to be carried out under-
b) Creep
Incandescent light.
19) A person is said to be truly color blind when he cannot c) Fatigue and cause cannot be determined
distinguish red and green
d) Fatigue and cause can be determined
20) The lens of the eye focuses Each wavelength at different
4) Size of unequal fillet wed leg length is
depth of focus in retina.
a) The sum of two unequal legs ( a + b )
1) How do you discriminate CREEP from FATIGUE d) The shortest distance between root to face.
Failure?
2) The best way to evaluate creep fracture is 6) The COLD TIP LIGHT is
b) Replication and Electron microscope b) Light transmitted through a fiber optic cable
analysis system to tip of the borescope .
b) Wave 14) The restriction of the angle between eye and the test
surface for general visual testing should be
c) Electromagnetic
a) less than 60°
d) Quantum
b) more than 60°
e) Both c and d
c) less than 30°
18) The CORNEA provides refractive ability about 22) The 20 /20 Snellen Vision test is usually performed at
c) 25 ft-Cd
d) B & C
a) 100ASA
b) 200 ASA
c) 400 ASA
d) 800 ASA