Professional Documents
Culture Documents
SearsCraftsman Router 315174710 Owners Manual
SearsCraftsman Router 315174710 Owners Manual
MANUAL
MODEL NO.
315.174710
in,,i ...............
CAUTION: ®
Warranty
Introduction
Operation
_l
Thank You for Buying
Craftsman Tools
in ,i.
Maintenance
,, Repair Parts
®
Designed exclusively for and sold only by
SEARS, ROEBUCK AND CO, Sears Tower, Chicago, IL 60684
612547-8! 5 PR}NTED IN U S A
4-92
INTRODUCTION
DOUBLE INSULATION Is a concept in safety, in electric IMPORTANT - Servicing of a tool with doubts Insulation
power tools, which eliminates the need for the usual three requires extreme care and knowledge of the system and
wire grounded power cord and grounded supply system, should be performed only by a qualified service technician.
Wherever there is electric current in the tool there are two For service we suggest you return the toot to your nearest
complete sets of insulationto protect the user, All exposed Sears Store for repatr_ Always use original factory replace-
metal parts are isolated from internal metal motor compo- ment parts when servicing.
nents with protecting insulation.
2 Hll Ir"ll'l ,,,,_L- ....... ,i I i ,= L' '1, _ " ,,r=_r= ..... _ .................... - _ .............
WRENCH
"LOCK.ON"
WRENCH BUTTON
SPINDLE
CLAMPING
HANDLE
HANDLE
DEPTH
STOPRINGS
CHIP SHIELD
A clear plastic chip shieid is installed on the front of your router for protection against ftytng dust and chips. The shtetd is
designed to fit the front opening of the router base. See Figure 1. If necessary to remove chlp shield, squeeze the tabs on
each end and puil outward, To replace, squeeze the tabs at each end, fit into the opening, then ralease_ FOR YOUR
PROTECTION DO NOT USE ROUTER WITHOUT CHIP SHIELD PROPERLY IN PLACE.
"LOCK-ON" BUTTON
The switch of your router is equipped with a "lock-on" feature which is convenient when operating for extended periods of
time. To lock on, depress the trigger, push in the lock button located on the side of the handle, then while holding the lock
button pushed in, retease the trigger To release the lock, depress the trigger and release it See Figure 1.
WRENCH STORAGE AREA
Your router has a wrench storage area located on the top end cap portionof the motor houstng, When installingor removing
cutters remove the wrench from its storage area Proper storage of wrench when not in use w{II help reduce the possibttiity of
tosingwrench. S_a Figure 1,
The operation of any router can reautt In foreign objects being thrown Into your eyes, wht.ch
can result In severe eye damage, Before commencing power tool operation, always wear
safety goggles or safety grasses wtth side shietds and a furl face shield when needed. We
recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses wlth
side shields, available at Sears Catalog Order or Retail Stores.
........................ ,,,,,i,H, H , i
Page 4
Fig. 2
TO LOCK
ELECTRICAL CONNECTION
Your router has a precision built electric motor+ ft should be
DEPTHOF CUT ADJUSTMENTS connected to a power supply that is 120 volts, 60 Hz, AC
only (normal household current). Do not operate this tool
See Figures 3 and 4
on direct current (DC) A voltage drop of more than 10
We recommend thai cuts be made at a depth not exceeding percent will cause a loss of power and overheating If your
1/8" and that several passes be made to reach depths of cut tool does not operate when plugged into an oulIet, double-
greater than 1/8" check the power supply rating
Page 5
Page 6
FORCE FEEDING
Clean, smooth routingand edge shaping can be done only
when the bit is revolving at a relatively high speed end is
takingvery small bites to producetiny,cleanly severed chips.
If your muter is forced to move forward too fast, the RPM of
the bit becomes slower than normal in relation to itsforward
movement.. As a result, the bit must take bigger bites as it
revoiveso "Bigger bites" mean bigger chips, and a roughcr
finish. Biggcr chips also require more powcr, which could J
2ND. PASS
As previously mentioned, the depth of cut is important be-
cause it affects the rate of feed which, in turn, affects the 1ST, PASS I,.1_1 1ST. PASS
quality of a cut (and, atso, the possibility of damage to your
router motor and bit) A deep cut requires a slower feed than
a shallow one, and a too deep cut will cause you to slow the
feed so much thai the bit is no longer cutting, it is scraping,
instead.
Making a deep cut is never advisable. The smaller bits-- --_""---""-_'_'_ Fig. 10
especia}[y those only !/16 inch in diameter --are easily
broken off when subjected to too much side thrust A large
,,,H,
GU,DE
OUTS,DE
enough bit may not be broken off, but if the cut is too deep a
rough cut will result-- and it may be very difficult to guide and R_OTATIO._
N ('_,_
control the bit as desired For these reasons, we recommend
that you do not exceed 1/8 inch depth of cut in a single pass,
regardless of the bif size or the softness or condition of the
workptece_ See Figure 9
To make deeper cuts it is therefore necessary to make as
GUIDE"
many successive passes as required, lowering the bit 1/8
j ......
inch for each new pass In order to save time, do all the cutting
necessary at one depth setting, before lowering the bit forthe
next pass This wtllatso assure a uniform depth when the final
pass _scompleted. See Figure 10.
ROTATION
DIRECTION OF FEED AND THRUST
The routermotor and bff revolve in a clockwisedirection. This THRUST FEED
gives the tool a slfght tendency to twist (tn your hands) in a GUIDE INSIDE Fig, 11
counterclockwise direction, especially when the motor revs , ,, i i i
up (as at starting).
Because of the extremely high speed of bit rotation during a
"proper feeding" operation, there is very little kickback to
contend with under normal conditions. However, should the
bit strike a knot, hard grain, foreign object, etc. that would
ROUTING
affect the normal progress of the cuttingaction, there will be
a slight kickback---sufficient to spoil the trueness of your cut Whenever you are routing a groove, your travelshould be In
if you are not prepared. Such a kickback is always in the a direction that places whatever guide you are using at the
direction opposite to the direction of bit rotation. right-hand side. In short, when the guide is positioned as
TO guard against such a kickback, plan your set-up and shown in the first part of Figure 11, tool travel should be _eft
direction of feed so that you will always be thrusting the tool-- to right and counterclockwise around curves. When the guide
tohold it against whatever you are using to guide the cut--in is positionedas shown in the second part of Figure 11 tool
the same direction that the teadingedge of the bit is moving travel should be right to left and clockwise around curves. If
In shod, the thrust should be in a direction that keeps the there is a choice, the first set-up is generally the easiest to
sharp edges of the bit continuously biting straight into new use In eithercase, the sideways thrust you use is against the
(uncut) wood. guide.
Page 8
Upon completion of cut, tum motor off and let it come to a TOP EDGE SHAPING
complete stop before removing router from work suflace_ ..,11 i .i ,,.,, .H , i ..... . _
Page 9
J
I i,i] ..... .
C
2, Remove screws (A) and handle cover (B). See Figure D
13.
3, NOTE THE LOCATION OF THE MOLDED BEND RE-
LIEF (C) ON THE POWER HANDLE CORD, ALSO
NOTE ALL WIRING IN THE HANDLE AND HOW EACH
LEAD IS CONNECTED TO THE SWITCH° Connec*
lions and wiring position must be identical when instafl_
trig new switch, See Figure 13
4 Remove leads from switch (D) by inserting a 1/32"
diameter nail or pin into switch teed receptacle and Fig. 13
putting on lead as shown in figure _4 Remove nail or ,, 11
DEPTH
ADJUSTING I
DEPRESS LIP
BASE _
Fig, 15
Page 10
Page 11
GENERAL
Only the parts shown on parts list, page 15, are intended to When electric tools are used on fiberglass boats, sports
be repaired or replaced by the customer All other parts cars, wallboard, spackling compounds, or plaster, it has
represent an important part of the double insulation system been found that they are subject to accelerated wear and
and should be serviced only by a qualified Sears service possible premature failure, as the fiberglass chips and
technician. grindings are highly abrasive to bearings, brushes,
commulator, etc Consequently, it [s not recommended that
Avoid using solvents when eteaning plastic parts. Most
this tool be used for extended work on any fiberglass material,
plastics are suscept+ble to various types of commercial
wa!iboard; ° spack+ing compounds, or ptaster. During any
solvents and may be damaged by their use Use clean
use on fiberglass it is extremely important that the tool is
cloths to remove dirt, carbon dust, etc
cleaned frequently by blowing with an air jet
y +
Page 12
,, ,,,
VEINING CORE BOX STRAIGHT i OMBI., HINGE iRABBETi OGEE j COVE I BEAD ARBOR
NATIONl BffS BIT FACE NATION MORTISING CUTTER BIT i I
BIT I QUARTER,
25_
PANEL I BITS STRAIGHT, BIT BFI_ ROUND
tin'rim I BEVEL i 3/16_ i 263ol.518" ] BITS
CUTTER 2_305
O i
i '25576-3/8"
"2_575-.It_"
I
I
26330-1/_"
26329-3J16"
2632_"1/4"
;t6326-,1,_"
V-GROOVE
LI @ E3]
CHAMFER
26_28-7/32" FO_
25315-1t_"
26327-I14 =
26314_ _
"2541 i
1/4", 5/16_ ROMAN Of= &R _ 1
25313-1/2" VEN_ER 25309_114"
"25,_03,114"
SALL
BEARING, _
|112 & 5ll_'
26333
_25_82 26303 I "25586,,3/_"
;_6322_ft2" BEVEL "25504,t14" I *2Sag5
"25S78-f/2" "25827-1t2" "255_5,1Z2"
_2_506-314"
F 7_,,_,o,T,,,,o.,,_' L_J
HELPFUL HINTS
,/ Always clamp workplace securely before routing,
,/ A safe operator is one who thinks ahead,
,/ Make set-up adjustments carefully, Then double check. Measure twice and cut once.
,/ Keep cutters ciean and properly sharpened.
,/' Don't let familiarity make you caretesso
Page 13
15
21 12 1_ 12 5
NOTE: _A" - The assembly shown represents an important part of the Double Insulated System. To avoid the
possibility of alteration or damage to the System, service should be performed by your nearest Sears
Repair Center° Contact your nearest Sears Catalog Order or Retail Store.
Page !4
[
, ,,, ,, ,, , , ,,i, ,,,,, , ,,,, ,,, ,,,,,,,,,t i,,,i,,,,,,, i , u
The model number will be found on a plateattached to the motor houslng. Always mention the model number
in all correspondence regarding your ROUTER or when ordering repair parts, !
SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS
PARTS LIST
Key Part
No. Number Description Quan,
1 970855-001 " Screw (#5-20 x 3/8" Hi-Lo FiL Hd.) ..............................................................
!
2 612866-001 Cap Screw (#5-40 x 1/4= Soc Hd,) ..................................................... 1
3 970510-001 Lock Button ...................................................................................... t
4 970692-001 Label ............................................. _ .......................................................... 1
5 970518-001 Data Plate ......................................................................................................1
6 989985-003 Collet Nut (1/4")................................................................................
:............ 1
7 970504-001 Depth Adjusting Ring ................................................................................ t
8 703774-005 Steel Baft (3/t6) .............................................................................................
6
9 990146-002 " Screw (#10-32 x 15/16" Fil, Hd,) .................................................................1
t0 968700-007 " Screw (#6-19 x 1/2" Pan Hal) ................................................................... 1
11 989935-006 Wrench (9/t6") ......................... ,.:,.......................................................... 1
12 971538-000 Power Handle Assembly ............................................................................... 1
13 606066-004 " Screw (#10-32 x 3/4" Pan Hdo) ............................................................... 4
14 623814-004 Switch ......................................................................................................... 1
15 617966-028 " Screw (#8-10 x 1/2" Pan Hal,) ........................................................................
8
t6 970503_003 Base ...................................................................................................................
I
17 612191-004 Subbase .................................................................................................. t
18 998586-001 * Screw (#t0-32 x 1/4" Pan Hd,) ..................................................................3
19 606688-002 Ghtp Shield .............................................................................................. 1
20 9705t9-091 Logo Plate .................................................................................................. 1
21 970697-000 Handle Assembly ..................................................................................... t
22 94t401-835 Roll Pin................................................................................................... 1
23 970505-001 Stop Ring ........................................................................................... 2
24 970511_001 Clamping Lever ........................................................................................ 1
25 9705t5-001 Slide Nut (#t0-32) .......................................................................... 1
612547-815 Owner's Manual
Page 15
OWNER'S Router
MANUAL
Double Insulated
MODEL NO. The model number of your Router will be found on a plate
attached to the motor housing.
315.174710
If the parts you need are not stocked locally, your order
will be electronically transmitted to a Sears Repair Parts
Distribution Center for handling,