Professional Documents
Culture Documents
200 20 Pi DTS 00001
200 20 Pi DTS 00001
D1BM APPLICABILITY
RGE Comp. Hub 6S
Comp. Hub 7S
Comp. Hub 8S
Comp. Hub 4S
RL Comp. Hub 1S
QG2 Comp. Hub 4N
Comp. Hub 6N
Cktan
Chee Seng Loh
Kishore Kumar JAYAKUMAR Swapnil Kulkarni 2021.07.28
2021.07.28
15:45:59
2021.07.28 16:30:51
2021.07.28 12:37:11 +05'30' 15:32:33 +08'00'
+08'00' +08'00'
B 6 15 Updated the Table Header detail and format for the Codes
and Standard
B 7 19 Updated the Table Header detail and format for the Project
Document References
HOLD LIST
Contents
1 INTRODUCTION ........................................................................................................................... 5
2 DEFINITIONS AND ACRONYMS ................................................................................................. 6
2.1 Definitions ............................................................................................................................ 6
2.2 Acronyms ............................................................................................................................. 6
3 PURPOSE OF DOCUMENT ......................................................................................................... 7
3.1 General ................................................................................................................................ 7
4 BALL VALVE INDEX ..................................................................................................................... 7
5 ORDER OF PRECEDENCE ....................................................................................................... 15
6 APPLICABLE CODES & STANDARDS ...................................................................................... 16
6.1 API–American Petroleum Institute..................................................................................... 16
6.2 ASME–American Society Of Mechanical Engineers ......................................................... 16
6.3 ASTM - American Society for Testing and Material .......................................................... 17
6.4 BSI–British Standards Institution ....................................................................................... 18
6.5 MSS–Manufacturers Standardization Society ................................................................... 18
6.6 EEMUA – Engineering Equipment and Materials Users Association ................................ 19
6.7 NACE - National Association of Corrosion Engineers ....................................................... 19
7 REFERENCES ............................................................................................................................ 19
APPENDIX-1 DATASHEETS FOR MANUAL BALL VALVES (NON - CLADDED VALVES) ............... 20
APPENDIX-2 DATASHEETS FOR MANUAL BALL VALVES (CLADDED VALVES) .......................... 21
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 3 of 21
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
NFPS Compression Project FEED
Figures
Figure 1-1: North Field Context ............................................................................................................... 5
Tables
Table 4-1 : Ball Valves Index (Non-Cladded Valves) .............................................................................. 7
Table 4-2: Ball Valves Index (Cladded Valves)..................................................................................... 14
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 4 of 21
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
NFPS Compression Project FEED
1 INTRODUCTION
The reservoir pressure in Qatar’s North Field has been declining due to continuous production since
the early 1990s. The North Field is the world’s largest natural gas field and accounts for nearly all of the
state of Qatar’s gas production. The principal objective of the NFPS project is to sustain plateau from
existing QG South Operation – RL Dry Gas, RGE Wet gas and existing QG North Operation – QG1 &
QG2, production areas by implementing an integrated and optimum investment program consisting of
subsurface development, pressure drop reduction steps and compression. Refer to figure below for a
schematic of North Field.
Figure 1-1: North Field Context
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 5 of 21
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
NFPS Compression Project FEED
Drilling and Looping Investments #1 and #2 are in execution phase and are being executed by I1P1
EPC, EPCO and EPCL projects with the exception of WHP13N, which will be part of NFPS
Compression project execution. The NFPS Compression Project involves the installation of large
offshore compression facilities at multiple locations. The compression facilities will be installed after the
completion of the Drilling and Looping Projects.
Qatargas Operating Company Limited is leading the development of the North Field Production
Sustainability (NFPS) Project. The principal objective of the NFPS project is to economically sustain
plateau from existing QG South (RGE, RL) and QG North (QG1 & QG2) production assets by
implementing an integrated and optimum investment program consisting of subsurface developments,
pressure drop reduction steps and offshore compression facilities installation.
CONTRACTOR is awarded to perform FEED for NFPS Compression Project – RGE, RL and QG2
Facilities.
2 DEFINITIONS AND ACRONYMS
2.1 Definitions
The following definitions used in the present PROJECT procedure are:
PROJECT NFPS Compression Project FEED
COMPANY Qatargas Operating Company limited
CONTRACTOR Middle East Projects International (Technip MEPI)
EPC CONTRACTOR CONTRACTOR engaged by COMPANY to execute EPC contract activities
or/and services
SUBCONTRACTOR A party who is providing subcontracted services specified and ordered by
CONTRACTOR or EPC CONTRACTOR
THIRD PARTY Third Party appointed by CONTRACTOR
VENDOR (SUPPLIER) A party who is responsible to manufacture and supply equipment and/or
services
SUB-VENDOR A party who is responsible to manufacture and supply equipment and/or
(SUB-SUPPLIER) services under responsibility of main VENDOR
SHALL The word “Shall” is to be understood as a mandatory requirement.
SHOULD The word “Should” is to be understood as strongly recommended.
MAY The word “May” is to be understood as an action to be undertaken at
CONTRACTOR / COMPANY ‘s discretion and upon evaluation of a review of
the circumstances of the issue in question.
2.2 Acronyms
The following acronyms are used in this document.
Term Description
AED Anti Explosive Decompression
API American Petroleum Institute
ASME American Society of Mechanical Engineers
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 6 of 21
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
NFPS Compression Project FEED
3.1 General
This document covers the technical requirements for the Ball Valves data Sheets for offshore topside
piping. This document shall be read in conjunction with Specification for Manual valves document
number 200-20-PI-SPC-00006 [3].
4 BALL VALVE INDEX
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 7 of 21
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
NFPS Compression Project FEED
APPENDIX-1
PIPING VALVE END
SIZE BORE DATASHEET
CLASS RATING CONNECTIONS
NUMBER
NPS 8" A1E 150 Reduced Bore FLGD - RF 3 of 223
NPS 0.5" to 1.5" A1E 150 Full Bore FLGD - RF 4 of 223
NPS 2" to 4" A1E 150 Full Bore FLGD - RF 5 of 223
NPS 6" A1E 150 Full Bore FLGD - RF 6 of 223
NPS 8" A1E 150 Full Bore FLGD - RF 7 of 223
NPS 0.5" to 1.5" A5E 150 Reduced Bore FLGD - RF 8 of 223
NPS 2" to 6" A5E 150 Reduced Bore FLGD - RF 9 of 223
NPS 8" A5E 150 Reduced Bore FLGD - RF 10 of 223
NPS 10" A5E 150 Reduced Bore FLGD - RF 11 of 223
NPS 0.5" to 1.5" A5E 150 Full Bore FLGD - RF 12 of 223
NPS 2" to 4" A5E 150 Full Bore FLGD - RF 13 of 223
NPS 6" A5E 150 Full Bore FLGD - RF 14 of 223
NPS 8" to 10" A5E 150 Full Bore FLGD - RF 15 of 223
NPS 0.5" to 1.5" A6E 150 Reduced Bore FLGD - RF 16 of 223
NPS 2" to 6" A6E 150 Reduced Bore FLGD - RF 17 of 223
NPS 8" A6E 150 Reduced Bore FLGD - RF 18 of 223
NPS 10" to 24' A6E 150 Reduced Bore FLGD - RF 19 of 223
NPS 26" to 48' A6E 150 Reduced Bore BW 20 of 223
NPS 0.5" to 1.5" A6E 150 Full Bore FLGD - RF 21 of 223
NPS 2" to 4" A6E 150 Full Bore FLGD - RF 22 of 223
NPS 6" A6E 150 Full Bore FLGD - RF 23 of 223
NPS 8" to 24' A6E 150 Full Bore FLGD - RF 24 of 223
NPS 26" to 48' A6E 150 Full Bore BW 25 of 223
NPS 0.5" to 1.5" A7E 150 Reduced Bore FLGD - RF 26 of 223
NPS 2" to 6" A7E 150 Reduced Bore FLGD - RF 27 of 223
NPS 0.5" to 1.5" A7E 150 Full Bore FLGD - RF 28 of 223
NPS 2" to 4" A7E 150 Full Bore FLGD - RF 29 of 223
NPS 6" A7E 150 Full Bore FLGD - RF 30 of 223
NPS 0.5" to 1.5" A11A 150 Reduced Bore FLGD - RF 31 of 223
NPS 2" to 6" A11A 150 Reduced Bore FLGD - RF 32 of 223
NPS 8" A11A 150 Reduced Bore FLGD - RF 33 of 223
NPS 0.5" to 1.5" A11A 150 Full Bore FLGD - RF 34 of 223
NPS 2" to 4" A11A 150 Full Bore FLGD - RF 35 of 223
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 8 of 21
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
NFPS Compression Project FEED
APPENDIX-1
PIPING VALVE END
SIZE BORE DATASHEET
CLASS RATING CONNECTIONS
NUMBER
NPS 6" A11A 150 Full Bore FLGD - RF 36 of 223
NPS 8" A11A 150 Full Bore FLGD - RF 37 of 223
NPS 0.5" to 1.5" A19A 150 Reduced Bore FLGD - RF 38 of 223
NPS 2" to 6" A19A 150 Reduced Bore FLGD - RF 39 of 223
NPS 8" A19A 150 Reduced Bore FLGD - RF 40 of 223
NPS 10" A19A 150 Reduced Bore FLGD - RF 41 of 223
NPS 0.5" to 1.5" A19A 150 Full Bore FLGD - RF 42 of 223
NPS 2" to 4" A19A 150 Full Bore FLGD - RF 43 of 223
NPS 6" A19A 150 Full Bore FLGD - RF 44 of 223
NPS 8" to 10" A19A 150 Full Bore FLGD - RF 45 of 223
NPS 0.5" to 1.5" A33A 150 Reduced Bore FLGD - RF 46 of 223
NPS 2" to 4" A33A 150 Reduced Bore FLGD - RF 47 of 223
NPS 0.5" to 1.5" A33A 150 Full Bore FLGD - RF 48 of 223
NPS 2" to 4" A33A 150 Full Bore FLGD - RF 49 of 223
NPS 0.5" to 1.5" A34A 150 Reduced Bore FLGD - RF 50 of 223
NPS 2" to 6" A34A 150 Reduced Bore FLGD - RF 51 of 223
NPS 8" A34A 150 Reduced Bore FLGD - RF 52 of 223
NPS 10" to 12" A34A 150 Reduced Bore FLGD - RF 53 of 223
NPS 14" to 56" A34A 150 Reduced Bore BW 54 of 223
NPS 0.5" to 1.5" A34A 150 Full Bore FLGD - RF 55 of 223
NPS 2" to 4" A34A 150 Full Bore FLGD - RF 56 of 223
NPS 6" A34A 150 Full Bore FLGD - RF 57 of 223
NPS 8" to 12" A34A 150 Full Bore FLGD - RF 58 of 223
NPS 14" to 56" A34A 150 Full Bore BW 59 of 223
NPS 0.5" to 1.5" A35B 16 Barg Reduced Bore FLGD - FF 60 of 223
NPS 2" to 6" A35B 16 Barg Reduced Bore FLGD - FF 61 of 223
NPS 8" A35B 16 Barg Reduced Bore FLGD - FF 62 of 223
NPS 10" A35B 16 Barg Reduced Bore FLGD - FF 63 of 223
NPS 0.5" to 1.5" A35B 16 Barg Full Bore FLGD - FF 64 of 223
NPS 2" to 4" A35B 16 Barg Full Bore FLGD - FF 65 of 223
NPS 6" A35B 16 Barg Full Bore FLGD - FF 66 of 223
NPS 8" to 10" A35B 16 Barg Full Bore FLGD - FF 67 of 223
NPS 0.5" to 1.5" A37A 150 Reduced Bore FLGD - RF 68 of 223
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 9 of 21
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
NFPS Compression Project FEED
APPENDIX-1
PIPING VALVE END
SIZE BORE DATASHEET
CLASS RATING CONNECTIONS
NUMBER
NPS 2" to 4" A37A 150 Reduced Bore FLGD - RF 69 of 223
NPS 0.5" to 1.5" A37A 150 Full Bore FLGD - RF 70 of 223
NPS 2" to 4" A37A 150 Full Bore FLGD - RF 71 of 223
NPS 0.5" to 1.5" A45B 16 Barg Reduced Bore FLGD - FF 72 of 223
NPS 2" to 6" A45B 16 Barg Reduced Bore FLGD - FF 73 of 223
NPS 8" A45B 16 Barg Reduced Bore FLGD - FF 74 of 223
NPS 10" A45B 16 Barg Reduced Bore FLGD - FF 75 of 223
NPS 0.5" to 1.5" A45B 16 Barg Full Bore FLGD - FF 76 of 223
NPS 2" to 4" A45B 16 Barg Full Bore FLGD - FF 77 of 223
NPS 6" A45B 16 Barg Full Bore FLGD - FF 78 of 223
NPS 8" to 10" A45B 16 Barg Full Bore FLGD - FF 79 of 223
NPS 0.5" to 1.5" B1E 300 Reduced Bore FLGD - RF 80 of 223
NPS 2" to 4" B1E 300 Reduced Bore FLGD - RF 81 of 223
NPS 6" B1E 300 Reduced Bore FLGD - RF 82 of 223
NPS 0.5" to 1.5" B1E 300 Full Bore FLGD - RF 83 of 223
NPS 2" to 4" B1E 300 Full Bore FLGD - RF 84 of 223
NPS 6" B1E 300 Full Bore FLGD - RF 85 of 223
NPS 0.5" to 1.5" B6E 300 Reduced Bore FLGD - RF 86 of 223
NPS 2" to 4" B6E 300 Reduced Bore FLGD - RF 87 of 223
NPS 6" to 8" B6E 300 Reduced Bore FLGD - RF 88 of 223
NPS 10" to 24" B6E 300 Reduced Bore FLGD - RF 89 of 223
NPS 26" to 28" B6E 300 Reduced Bore BW 90 of 223
NPS 0.5" to 1.5" B6E 300 Full Bore FLGD - RF 91 of 223
NPS 2" to 4" B6E 300 Full Bore FLGD - RF 92 of 223
NPS 6" B6E 300 Full Bore FLGD - RF 93 of 223
NPS 8" to 24" B6E 300 Full Bore FLGD - RF 94 of 223
NPS 26" to 28" B6E 300 Full Bore BW 95 of 223
NPS 0.5" to 1.5" B19A 300 Reduced Bore FLGD - RF 96 of 223
NPS 2" to 4" B19A 300 Reduced Bore FLGD - RF 97 of 223
NPS 6" to 8" B19A 300 Reduced Bore FLGD - RF 98 of 223
NPS 10" B19A 300 Reduced Bore FLGD - RF 99 of 223
NPS 0.5" to 1.5" B19A 300 Full Bore FLGD - RF 100 of 223
NPS 2" to 4" B19A 300 Full Bore FLGD - RF 101 of 223
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 10 of 21
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
NFPS Compression Project FEED
APPENDIX-1
PIPING VALVE END
SIZE BORE DATASHEET
CLASS RATING CONNECTIONS
NUMBER
NPS 6" B19A 300 Full Bore FLGD - RF 102 of 223
NPS 8" to 10" B19A 300 Full Bore FLGD - RF 103 of 223
NPS 0.5" to 1.5" B34A 300 Reduced Bore FLGD - RF 104 of 223
NPS 2" to 4" B34A 300 Reduced Bore FLGD - RF 105 of 223
NPS 6" to 8" B34A 300 Reduced Bore FLGD - RF 106 of 223
NPS 10" to 12" B34A 300 Reduced Bore FLGD - RF 107 of 223
NPS 14" to 24" B34A 300 Reduced Bore BW 108 of 223
NPS 0.5" to 1.5" B34A 300 Full Bore FLGD - RF 109 of 223
NPS 2" to 4" B34A 300 Full Bore FLGD - RF 110 of 223
NPS 6" B34A 300 Full Bore FLGD - RF 111 of 223
NPS 8" to 12" B34A 300 Full Bore FLGD - RF 112 of 223
NPS 14" to 24" B34A 300 Full Bore BW 113 of 223
NPS 0.5" to 1.5" D5E 600 Reduced Bore FLGD - RF 114 of 223
NPS 2" to 4" D5E 600 Reduced Bore FLGD - RF 115 of 223
NPS 6" to 24" D5E 600 Reduced Bore FLGD - RF 116 of 223
NPS 0.5" to 1.5" D5E 600 Full Bore FLGD - RF 117 of 223
NPS 2" to 4" D5E 600 Full Bore FLGD - RF 118 of 223
NPS 6" to 24" D5E 600 Full Bore FLGD - RF 119 of 223
NPS 0.5" to 1.5" D7E 600 Reduced Bore FLGD - RF 120 of 223
NPS 2" to 4" D7E 600 Reduced Bore FLGD - RF 121 of 223
NPS 6" D7E 600 Reduced Bore FLGD - RF 122 of 223
NPS 0.5" to 1.5" D7E 600 Full Bore FLGD - RF 123 of 223
NPS 2" to 4" D7E 600 Full Bore FLGD - RF 124 of 223
NPS 6" D7E 600 Full Bore FLGD - RF 125 of 223
NPS 0.5" to 1.5" D19A 600 Reduced Bore FLGD - RF 126 of 223
NPS 2" to 4" D19A 600 Reduced Bore FLGD - RF 127 of 223
NPS 6" to 10" D19A 600 Reduced Bore FLGD - RF 128 of 223
NPS 0.5" to 1.5" D19A 600 Full Bore FLGD - RF 129 of 223
NPS 2" to 4" D19A 600 Full Bore FLGD - RF 130 of 223
NPS 6" to 10" D19A 600 Full Bore FLGD - RF 131 of 223
NPS 0.5" to 1.5" D34A 600 Reduced Bore FLGD - RF 132 of 223
NPS 2" to 4" D34A 600 Reduced Bore FLGD - RF 133 of 223
NPS 6" to 12" D34A 600 Reduced Bore FLGD - RF 134 of 223
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 11 of 21
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
NFPS Compression Project FEED
APPENDIX-1
PIPING VALVE END
SIZE BORE DATASHEET
CLASS RATING CONNECTIONS
NUMBER
NPS 14" to 24" D34A 600 Reduced Bore BW 135 of 223
NPS 0.5" to 1.5" D34A 600 Full Bore FLGD - RF 136 of 223
NPS 2" to 4" D34A 600 Full Bore FLGD - RF 137 of 223
NPS 6" to 12" D34A 600 Full Bore FLGD - RF 138 of 223
NPS 14" to 24" D34A 600 Full Bore BW 139 of 223
NPS 0.5" to 1.5" E5E 1500 Reduced Bore FLGD - RTJ 140 of 223
NPS 2" E5E 1500 Reduced Bore FLGD - RTJ 141 of 223
NPS 3" E5E 900 Reduced Bore FLGD - RTJ 142 of 223
NPS 4" to 24" E5E 900 Reduced Bore FLGD - RTJ 143 of 223
NPS 0.5" to 1.5" E5E 1500 Full Bore FLGD - RTJ 144 of 223
NPS 2" E5E 1500 Full Bore FLGD - RTJ 145 of 223
NPS 3" E5E 900 Full Bore FLGD - RTJ 146 of 223
NPS 4" to 24" E5E 900 Full Bore FLGD - RTJ 147 of 223
NPS 0.5" to 1.5" E7E 1500 Reduced Bore FLGD - RTJ 148 of 223
NPS 2" E7E 1500 Reduced Bore FLGD - RTJ 149 of 223
NPS 3" E7E 900 Reduced Bore FLGD - RTJ 150 of 223
NPS 4" to 6" E7E 900 Reduced Bore FLGD - RTJ 151 of 223
NPS 0.5" to 1.5" E7E 1500 Full Bore FLGD - RTJ 152 of 223
NPS 2" E7E 1500 Full Bore FLGD - RTJ 153 of 223
NPS 3" E7E 900 Full Bore FLGD - RTJ 154 of 223
NPS 4" to 6" E7E 900 Full Bore FLGD - RTJ 155 of 223
NPS 0.5" to 1.5" E34A 1500 Reduced Bore FLGD - RTJ 156 of 223
NPS 2" E34A 1500 Reduced Bore FLGD - RTJ 157 of 223
NPS 3" E34A 900 Reduced Bore FLGD - RTJ 158 of 223
NPS 4" to 12" E34A 900 Reduced Bore FLGD - RTJ 159 of 223
NPS 14" to 28" E34A 900 Reduced Bore BW 160 of 223
NPS 0.5" to 1.5" E34A 1500 Full Bore FLGD - RTJ 161 of 223
NPS 2" E34A 1500 Full Bore FLGD - RTJ 162 of 223
NPS 3" E34A 900 Full Bore FLGD - RTJ 163 of 223
NPS 4" to 12" E34A 900 Full Bore FLGD - RTJ 164 of 223
NPS 14" to 24" E34A 900 Full Bore BW 165 of 223
NPS 0.5" to 1.5" E37A 1500 Reduced Bore FLGD - RTJ 166 of 223
NPS 2" E37A 1500 Reduced Bore FLGD - RTJ 167 of 223
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 12 of 21
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
NFPS Compression Project FEED
APPENDIX-1
PIPING VALVE END
SIZE BORE DATASHEET
CLASS RATING CONNECTIONS
NUMBER
NPS 3" E37A 900 Reduced Bore FLGD - RTJ 168 of 223
NPS 4" E37A 900 Reduced Bore FLGD - RTJ 169 of 223
NPS 0.5" to 1.5" E37A 1500 Full Bore FLGD - RTJ 170 of 223
NPS 2" E37A 1500 Full Bore FLGD - RTJ 171 of 223
NPS 3" E37A 900 Full Bore FLGD - RTJ 172 of 223
NPS 4" E37A 900 Full Bore FLGD - RTJ 173 of 223
NPS 0.5" to 1.5" F7E1 1500 Reduced Bore FLGD - RTJ 174 of 223
NPS 2" F7E1 1500 Reduced Bore FLGD - RTJ 175 of 223
NPS 3" to 6" F7E1 1500 Reduced Bore FLGD - RTJ 176 of 223
NPS 0.5" to 1.5" F7E1 1500 Full Bore FLGD - RTJ 177 of 223
NPS 2" F7E1 1500 Full Bore FLGD - RTJ 178 of 223
NPS 3" to 6" F7E1 1500 Full Bore FLGD - RTJ 179 of 223
NPS 0.5" to 1.5" F11A 1500 Reduced Bore FLGD - RTJ 180 of 223
NPS 2" F11A 1500 Reduced Bore FLGD - RTJ 181 of 223
NPS 3" F11A 1500 Reduced Bore FLGD - RTJ 182 of 223
NPS 0.5" to 1.5" F11A 1500 Full Bore FLGD - RTJ 183 of 223
NPS 2" F11A 1500 Full Bore FLGD - RTJ 184 of 223
NPS 3" F11A 1500 Full Bore FLGD - RTJ 185 of 223
NPS 0.5" to 1.5" F25A 1500 Reduced Bore FLGD - RTJ 186 of 223
NPS 2" F25A 1500 Reduced Bore FLGD - RTJ 187 of 223
NPS 3" to 4" F25A 1500 Reduced Bore FLGD - RTJ 188 of 223
NPS 0.5" to 1.5" F25A 1500 Full Bore FLGD - RTJ 189 of 223
NPS 2" F25A 1500 Full Bore FLGD - RTJ 190 of 223
NPS 3" to 4" F25A 1500 Full Bore FLGD - RTJ 191 of 223
NPS 0.5" to 1.5" F34A 1500 Reduced Bore FLGD - RTJ 192 of 223
NPS 2" F34A 1500 Reduced Bore FLGD - RTJ 193 of 223
NPS 3" to 12" F34A 1500 Reduced Bore FLGD - RTJ 194 of 223
NPS 14" to 18" F34A 1500 Reduced Bore BW 195 of 223
NPS 0.5" to 1.5" F34A 1500 Full Bore FLGD - RTJ 196 of 223
NPS 2" F34A 1500 Full Bore FLGD - RTJ 197 of 223
NPS 3" to 12" F34A 1500 Full Bore FLGD - RTJ 198 of 223
NPS 14" to 18" F34A 1500 Full Bore BW 199 of 223
NPS 0.5" to 1.5" F37A 1500 Reduced Bore FLGD - RTJ 200 of 223
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 13 of 21
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
NFPS Compression Project FEED
APPENDIX-1
PIPING VALVE END
SIZE BORE DATASHEET
CLASS RATING CONNECTIONS
NUMBER
NPS 0.5" to 1.5" (1) F37A 1500 Reduced Bore FLGD - RTJ 201 of 223
NPS 2" F37A 1500 Reduced Bore FLGD - RTJ 202 of 223
NPS 2" (1) F37A 1500 Reduced Bore FLGD - RTJ 203 of 223
NPS 3" to 4" F37A 1500 Reduced Bore FLGD - RTJ 204 of 223
NPS 3" to 4" (1) F37A 1500 Reduced Bore FLGD - RTJ 205 of 223
NPS 0.5" to 1.5" F37A 1500 Full Bore FLGD - RTJ 206 of 223
NPS 0.5" to 1.5" (1) F37A 1500 Full Bore FLGD - RTJ 207 of 223
NPS 2" F37A 1500 Full Bore FLGD - RTJ 208 of 223
NPS 2" (1) F37A 1500 Full Bore FLGD - RTJ 209 of 223
NPS 3" to 4" F37A 1500 Full Bore FLGD - RTJ 210 of 223
NPS 3" to 4" (1) F37A 1500 Full Bore FLGD - RTJ 211 of 223
NPS 0.5" to 1.5" G7E 2500 Reduced Bore FLGD - RTJ 212 of 223
NPS 2" to 6" G7E 2500 Reduced Bore FLGD - RTJ 213 of 223
NPS 0.5" to 1.5" G7E 2500 Full Bore FLGD - RTJ 214 of 223
NPS 2" to 6" G7E 2500 Full Bore FLGD - RTJ 215 of 223
NPS 0.5" to 1.5" G11A 2500 Reduced Bore FLGD - RTJ 216 of 223
NPS 2" to 3" G11A 2500 Reduced Bore FLGD - RTJ 217 of 223
NPS 0.5" to 1.5" G11A 2500 Full Bore FLGD - RTJ 218 of 223
NPS 2" to 3" G11A 2500 Full Bore FLGD - RTJ 219 of 223
NPS 0.5" to 1.5" G37A 2500 Reduced Bore FLGD - RTJ 220 of 223
NPS 2" to 4" G37A 2500 Reduced Bore FLGD - RTJ 221 of 223
NPS 0.5" to 1.5" G37A 2500 Full Bore FLGD - RTJ 222 of 223
NPS 2" to 4" G37A 2500 Full Bore FLGD - RTJ 223 of 223
Note:
1. Ball Valves with Metal Seats.
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 14 of 21
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
NFPS Compression Project FEED
APPENDIX-2
PIPING VALVE END
SIZE BORE DATASHEET
CLASS RATING CONNECTIONS
NUMBER
NPS 8" to 16" A37A 150 Full Bore FLGD - RF 5 of 24
NPS 6" to 12" E37A 900 Reduced Bore FLGD - RTJ 6 of 24
NPS 14" to 48" E37A 900 Reduced Bore BW 7 of 24
NPS 6" to 12" E37A 900 Full Bore FLGD - RTJ 8 of 24
NPS 14" to 48" E37A 900 Full Bore BW 9 of 24
NPS 6" to 12" F25A 1500 Reduced Bore FLGD - RTJ 10 of 24
NPS 20" F25A 1500 Reduced Bore FLGD - RTJ 11 of 24
NPS 14" to 36" F25A 1500 Reduced Bore BW 12 of 24
NPS 6" to 12" F25A 1500 Full Bore FLGD - RTJ 13 of 24
NPS 14" to 36" F25A 1500 Full Bore BW 14 of 24
NPS 6" to 12" F37A 1500 Reduced Bore FLGD - RTJ 15 of 24
NPS 6" to 12" (1) F37A 1500 Reduced Bore FLGD - RTJ 16 of 24
NPS 14" to 36" F37A 1500 Reduced Bore BW 17 of 24
NPS 6" to 12" F37A 1500 Full Bore FLGD - RTJ 18 of 24
NPS 6" to 12" (1) F37A 1500 Full Bore FLGD - RTJ 19 of 24
NPS 14" to 36" F37A 1500 Full Bore BW 20 of 24
NPS 6" to 12" G37A 2500 Reduced Bore FLGD - RTJ 21 of 24
NPS 14" G37A 2500 Reduced Bore BW 22 of 24
NPS 6" to 12" G37A 2500 Full Bore FLGD - RTJ 23 of 24
NPS 14" G37A 2500 Full Bore BW 24 of 24
Note:
1. Ball Valves with Metal Seats.
5 ORDER OF PRECEDENCE
In general the order of precedence shall be as follows:
a) Qatari Governmental and Regulatory Requirements
b) COMPANY Policies and Procedures
c) Project Specifications
d) Industry Codes and Standards
e) COMPANY and CONTRACTOR’S lessons learned
If CONTRACTOR / VENDOR deems any deviations from the specifications will result in significant
project cost and schedule saving, proposal to such deviations shall be submitted to COMPANY for
review and approval. CONTRACTOR / VENDOR shall not proceed with any deviation to the
Specifications without prior COMPANY APPROVAL.
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 15 of 21
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
NFPS Compression Project FEED
[2] API SPEC 6FA Specification for Fire Test for Valves
[4] API STD 607 Fire Test for Soft-Seated Quarter-Turn Valves
[5] API STD 608 Metal Ball valves-Flanged, Threaded and Welding Ends.
[1] ASME B16.5 Pipe Flanges and Flanged Fittings NPS 1/2 Through NPS 24
Metric/Inch Standard
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 16 of 21
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
NFPS Compression Project FEED
[1] ASTM A105 Standard Specification for Carbon Steel Forgings for Piping
Applications
[2] ASTM A182 Standard Specification for Forged or Rolled Alloy and Stainless Steel
Pipe Flanges, Forged Fittings, and Valves and Parts for High-
Temperature Service
[3] ASTM A193 Standard Specification for Alloy-Steel and Stainless Steel Bolting
Materials for High- Temperature Service
[4] ASTM A194 Standard Specification for Carbon and Alloy Steel Nuts for Bolts for
High Pressure or High Temperature Service, or Both
[5] ASTM A216 Standard Specification for Steel Castings, Carbon, Suitable for Fusion
Welding, for High-Temperature Service
[6] ASTM A276 Standard Specification for Stainless Steel Bars and Shapes
[7] ASTM A320 Standard Specification for Alloy/Steel Bolting Materials for Low-
Temperature Service
[8] ASTM A350 Standard Specification for Carbon and Low-Alloy Steel Forgings,
Requiring Notch Toughness Testing for Piping Components
[9] ASTM A351 Standard Specification for castings, Austenitic, Austenitic- Ferritic
(Duplex), for Pressure-Containing Parts
[10] ASTM A352 Standard Specification for Steel Castings, Ferritic and Martensitic,
for Pressure Containing Parts, Suitable for Low-Temperature
Service
[11] ASTM A487 Standard Specification for Steel Castings Suitable for Pressure
Service
[12] ASTM A494 Standard Specification for Castings, Nickel and Nickel Alloy
[15] ASTM B367 Standard Specification for Titanium and Titanium Alloy
Castings
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 17 of 21
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
NFPS Compression Project FEED
[16] ASTM B381 Standard Specification for Titanium and Titanium Alloy Forgings
[19] ASTM F467 Standard Specification for Nonferrous Nuts for General Use nominal
diameter~ non-ferrous alloys~ Products and Services / Standards &
Publications / Standards Products
[20] ASTM F468 Standard Specification for Nonferrous Bolts, Hex Cap Screws, Socket
Head Cap Screws, and Studs for General Use
[21] ASTM A694/A694M Standard Specification for Carbon and Alloy Steel Forgings for Pipe
Flanges, Fittings, Valves, and Parts for High-Pressure Transmission
Service
[22] ASTM A703/703M Steel Castings, General Requirements, for Pressure-Containing Parts
[23] ASTM A961/961M Common Requirements for Steel Flanges, Forged Fittings,
Valves, and Parts for Piping Applications
[3] BSI BS EN 12266-1 Industrial Valves - Testing of Metallic Valves - Part 1: Pressure Tests,
Test Procedures and Acceptance Criteria – Mandatory Requirements
[1] MSS SP-25 Standard Marking System for Valves, Fittings, Flanges, and Unions
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 18 of 21
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
NFPS Compression Project FEED
[1] EEMUA 192 Guide for the procurement of valves for low temperature (non-
cryogenic) service.
7 REFERENCES
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 19 of 21
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
NFPS Compression Project FEED
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 20 of 21
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A1E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE Utility Air Distribution, Raw Diesel, Hazardous Open Drain (BF)
TYPE Reduced Bore
DESIGN API 608 / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A105N 8
BALL Floating Ball, Solid Ball ASTM A182 F316
SEAT Soft seat RPTFE 2
SEAT HOLDER ASTM A182 F316L
SEAT SPRING N/A
BODY SEAL Primary Seal & Firesafe Secondary Seal AED type and suitable for service 2
STEM / TRUNNION Shouldered anti-blow out ASTM A182 F316
STEM SEAL Elastomeric / Grafoil 2
A193 B7/A194 2H, Zn/Ni Plated +
BOLTING Alloy Steel 10
PTFE Coated
OPERATOR Lever Operator 4
MARKING MSS SP-25 7
INSPECTION & TESTS/
API 598 1, 5
ACCEPTANCE
TESTING Charpy test Yes
Leak test Yes
Torque test NO
CERTIFICATIONS API 607, EN 10204 Type 3.1
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 9
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves"
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification
200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A1E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE Utility Air Distribution, Raw Diesel, Hazardous Open Drain (BF)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A216 Gr WCB 8
BALL Floating Ball, Solid Ball ASTM A182 F316
SEAT Soft seat RPTFE 2
CAVITY VENT CONNECTION NO
SEAT HOLDER ASTM A182 F316L
SEAT SPRING N/A
BODY SEAL Primary Seal & Firesafe Secondary Seal AED type and suitable for service 2
STEM / TRUNNION Shouldered anti-blow out ASTM A182 F316
STEM SEAL Elastomeric / Grafoil 2
A193 B7/A194 2H, Zn/Ni Plated +
BOLTING Alloy Steel 10
PTFE Coated
OPERATOR Lever Operator 4
MARKING MSS SP-25 7
INSPECTION & TESTS/
API 6D 1, 5
ACCEPTANCE
TESTING Charpy test Yes
Leak test Yes
Torque test Yes (As per section 6.5.1 in 200-20-PI-SPC-00006)
CERTIFICATIONS API 6D, EN 10204 Type 3.1
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 9
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves"
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification
200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A1E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE Utility Air Distribution, Raw Diesel, Hazardous Open Drain (BF)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A216 Gr WCB 8
BALL Floating Ball, Solid Ball ASTM A182 F316
SEAT Soft seat RPTFE 2
CAVITY VENT CONNECTION NO
SEAT HOLDER ASTM A182 F316L
SEAT SPRING N/A
BODY SEAL Primary Seal & Firesafe Secondary Seal AED type and suitable for service 2
STEM / TRUNNION Shouldered anti-blow out ASTM A182 F316
STEM SEAL Elastomeric / Grafoil 2
A193 B7/A194 2H, Zn/Ni Plated +
BOLTING Alloy Steel 10
PTFE Coated
OPERATOR Gear operator 4, 11
MARKING MSS SP-25 7
INSPECTION & TESTS/
API 6D 1, 5
ACCEPTANCE
TESTING Charpy test Yes
Leak test Yes
Torque test Yes (As per section 6.5.1 in 200-20-PI-SPC-00006)
CERTIFICATIONS API 6D, EN 10204 Type 3.1
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 9
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves"
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener
during assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting
specification 200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A1E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE Utility Air Distribution, Raw Diesel, Hazardous Open Drain (BF)
TYPE Full Bore
DESIGN API 608 / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A105N 8
BALL Floating Ball, Solid Ball ASTM A182 F316
SEAT Soft seat RPTFE 2
SEAT HOLDER ASTM A182 F316L
SEAT SPRING N/A
BODY SEAL Primary Seal & Firesafe Secondary Seal AED type and suitable for service 2
STEM / TRUNNION Shouldered anti-blow out ASTM A182 F316
STEM SEAL Elastomeric / Grafoil 2
A193 B7/A194 2H, Zn/Ni Plated +
BOLTING Alloy Steel 10
PTFE Coated
OPERATOR Lever Operator 4
MARKING MSS SP-25 7
INSPECTION & TESTS/
API 598 1, 5
ACCEPTANCE
TESTING Charpy test Yes
Leak test Yes
Torque test NO
CERTIFICATIONS API 607, EN 10204 Type 3.1
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 9
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves"
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification
200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A1E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE Utility Air Distribution, Raw Diesel, Hazardous Open Drain (BF)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A216 Gr WCB 8
BALL Floating Ball, Solid Ball ASTM A182 F316
SEAT Soft seat RPTFE 2
CAVITY VENT CONNECTION NO
SEAT HOLDER ASTM A182 F316L
SEAT SPRING N/A
BODY SEAL Primary Seal & Firesafe Secondary Seal AED type and suitable for service 2
STEM / TRUNNION Shouldered anti-blow out ASTM A182 F316
STEM SEAL Elastomeric / Grafoil 2
A193 B7/A194 2H, Zn/Ni Plated +
BOLTING Alloy Steel 10
PTFE Coated
OPERATOR Lever Operator 4
MARKING MSS SP-25 7
INSPECTION & TESTS/
API 6D 1, 5
ACCEPTANCE
TESTING Charpy test Yes
Leak test Yes
Torque test Yes (As per section 6.5.1 in 200-20-PI-SPC-00006)
CERTIFICATIONS API 6D, EN 10204 Type 3.1
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 9
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves"
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener
during assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification
200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A1E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE Utility Air Distribution, Raw Diesel, Hazardous Open Drain (BF)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A216 Gr WCB 8
BALL Floating Ball, Solid Ball ASTM A182 F316
SEAT Soft seat RPTFE 2
CAVITY VENT CONNECTION NO
SEAT HOLDER ASTM A182 F316L
SEAT SPRING N/A
BODY SEAL Primary Seal & Firesafe Secondary Seal AED type and suitable for service 2
STEM / TRUNNION Shouldered anti-blow out ASTM A182 F316
STEM SEAL Elastomeric / Grafoil 2
A193 B7/A194 2H, Zn/Ni Plated +
BOLTING Alloy Steel 10
PTFE Coated
Gear operator
OPERATOR 4, 11
MARKING MSS SP-25 7
INSPECTION & TESTS/
API 6D 1, 5
ACCEPTANCE
TESTING Charpy test Yes
Leak test Yes
Torque test Yes (As per section 6.5.1 in 200-20-PI-SPC-00006)
CERTIFICATIONS API 6D, EN 10204 Type 3.1
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 9
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves"
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener
during assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting
specification 200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A1E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE Utility Air Distribution, Raw Diesel, Hazardous Open Drain (BF)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A216 Gr WCB 8
BALL Trunnion Mounted Ball, Solid Ball ASTM A182 F316
SEAT Soft seat RPTFE 2
CAVITY VENT CONNECTION NO
SEAT HOLDER ASTM A182 F316L
SEAT SPRING INCONEL X750
BODY SEAL Primary Seal & Firesafe Secondary Seal AED type and suitable for service 2
STEM / TRUNNION Shouldered anti-blow out ASTM A182 F316
STEM SEAL Elastomeric / Grafoil 2
A193 B7/A194 2H, Zn/Ni Plated +
BOLTING Alloy Steel 10
PTFE Coated
OPERATOR Gear operator 4, 11
MARKING MSS SP-25 7
INSPECTION & TESTS/
API 6D 1, 5
ACCEPTANCE
TESTING Charpy test Yes
Leak test Yes
Torque test Yes (As per section 6.5.1 in 200-20-PI-SPC-00006)
CERTIFICATIONS API 6D, EN 10204 Type 3.1
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 9
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves"
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener
during assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting
specification 200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
13. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A5E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE LP Fuel Gas
TYPE Reduced Bore
DESIGN API 608 / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A5E Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE LP Fuel Gas
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A5E Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE LP Fuel Gas
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A5E Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE LP Fuel Gas
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
13. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A5E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE LP Fuel Gas
TYPE Full Bore
DESIGN API 608 / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A5E Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE LP Fuel Gas
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A5E Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE LP Fuel Gas
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A5E Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE LP Fuel Gas
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
13. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A6E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Cooling Water Circulation (NACE)
TYPE Reduced Bore
DESIGN API 608 / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A105N 8
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A6E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Cooling Water Circulation (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A216 Gr WCB 8
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A6E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Cooling Water Circulation (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A216 Gr WCB 8
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A6E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Cooling Water Circulation (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A216 Gr WCB 8
BALL Trunnion Mounted Ball, Solid Ball ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification
200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
14. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A6E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Cooling Water Circulation (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern) (Upto 36") / Manufacturer Standard (Size 38" and above)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Butt Weld Ends with Pup pieces to suit Pipe wall thickness 3,12
BODY / BONNET Top Body ASTM A216 Gr WCB 8
BALL Trunnion Mounted Ball, Solid Ball ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or
deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3 Valve end wall thickness shall be as per ASME B16.25 to suit the following pipe wall thickness as mentioned in MTO description.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable for
Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12 Valve shall be provided with 800MM body extensions (or) welded-on pipes to allow field welding and PWHT, if specified,without disassembly,
distortion (or) damage to non-metallic internals. The material of the extension shall be forged (or) cast as a part of the body or shall be A672 Gr.B60
Cl.22, EFW pipe material.The body extension wall thickness shall be as per thickness mentioned in the MTO description. Pressure testing shall be
performed after welding and heat treatment.
13. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
14. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
15. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A6E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Cooling Water Circulation (NACE)
TYPE Full Bore
DESIGN API 608 / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A105N 8
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A6E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Cooling Water Circulation (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A216 Gr WCB 8
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A6E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Cooling Water Circulation (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A216 Gr WCB 8
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A6E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Cooling Water Circulation (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A216 Gr WCB 8
BALL Trunnion Mounted Ball, Solid Ball ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
14. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A6E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 3
CORROSION ALLOWANCE 3 mm
SERVICE Cooling Water Circulation (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern) (Upto 36") / Manufacturer Standard (Size 38" and above)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Butt Weld Ends with Pup pieces to suit Pipe wall thickness 11, 12
BODY / BONNET Top Body ASTM A216 Gr WCB 8
BALL Trunnion Mounted Ball, Solid Ball ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or
deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable for
Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. Valve end wall thickness shall be as per ASME B16.25 to suit the following pipe wall thickness as mentioned in MTO description.
12 Valve shall be provided with 800MM body extensions (or) welded-on pipes to allow field welding and PWHT, if specified,without disassembly,
distortion (or) damage to non-metallic internals. The material of the extension shall be forged (or) cast as a part of the body or shall be A672 Gr.B60
Cl.22, EFW pipe material.The body extension wall thickness shall be as per thickness mentioned in the MTO description. Pressure testing shall be
performed after welding and heat treatment.
13. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
14. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
15. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A7E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
TYPE Reduced Bore
DESIGN API 608 / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -46°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A350 LF2 Cl.1 8
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or
deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable for
Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A7E Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -46°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A352 Gr LCC 8
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification
200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003
- Material Requirements for Sour Service
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A7E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
TYPE Full Bore
DESIGN API 608 / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -46°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A350 LF2 Cl.1 8
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or
deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable for
Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A7E Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -46°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A352 Gr LCC 8
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification
200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003
- Material Requirements for Sour Service
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A7E Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -46°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A352 Gr LCC 8
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification
200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-
00003 - Material Requirements for Sour Service
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A11A Notes
Offering
MATERIAL GROUP Group 2.2
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
Instrument Air Distribution, Demineralised Water, Portable Water Distribution,
SERVICE
Chemical Injection, Breathing Air, Nitrogen Generation & Distribution
TYPE Reduced Bore
DESIGN API 608 / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A182 F316/316L
BALL Floating Ball, Solid Ball ASTM A182 F316
SEAT Soft seat RPTFE 2
SEAT HOLDER ASTM A182 F316L
SEAT SPRING N/A
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM / TRUNNION Shouldered anti-blow out ASTM A182 F316
STEM SEAL Elastomeric / Grafoil 2
ASTM F468 UNS N06625
BOLTING
ASTM F467 UNS N06625
OPERATOR Lever operator 4
MARKING MSS SP-25 7
TESTING Charpy test No
Leak test Yes
Torque test NO
INSPECTION & TESTS/
API 598 1, 5
ACCEPTANCE
CERTIFICATIONS API 607, EN 10204 Type 3.1
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 8
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves"
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification
200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A11A Notes
Offering
MATERIAL GROUP Group 2.2
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
Instrument Air Distribution, Demineralised Water, Portable Water Distribution,
SERVICE
Chemical Injection, Breathing Air, Nitrogen Generation & Distribution
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A351 CF8M
BALL Floating Ball, Solid Ball ASTM A182 F316
SEAT Soft seat RPTFE 2
CAVITY VENT CONNECTION NO
SEAT HOLDER ASTM A182 F316L
SEAT SPRING N/A
BODY SEAL Primary Seal & Firesafe Secondary Seal AED type and suitable for service 2
STEM / TRUNNION Shouldered anti-blow out ASTM A182 F316
STEM SEAL Elastomeric / Grafoil 2
ASTM F468 UNS N06625
BOLTING
ASTM F467 UNS N06625
OPERATOR Lever operator 4
MARKING MSS SP-25 7
INSPECTION & TESTS/
API 6D 1, 5
ACCEPTANCE
TESTING Charpy test No
Leak test Yes
Torque test Yes (As per section 6.5.1 in 200-20-PI-SPC-00006)
CERTIFICATIONS API 6D, EN 10204 Type 3.1
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 8
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves"
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification
200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A11A Notes
Offering
MATERIAL GROUP Group 2.2
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
Instrument Air Distribution, Demineralised Water, Portable Water Distribution,
SERVICE
Chemical Injection, Breathing Air, Nitrogen Generation & Distribution
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A351 CF8M
BALL Floating Ball, Solid Ball ASTM A182 F316
SEAT Soft seat RPTFE 2
CAVITY VENT CONNECTION NO
SEAT HOLDER ASTM A182 F316L
SEAT SPRING N/A
BODY SEAL Primary Seal & Firesafe Secondary Seal AED type and suitable for service 2
STEM / TRUNNION Shouldered anti-blow out ASTM A182 F316
STEM SEAL Elastomeric / Grafoil 2
ASTM F468 UNS N06625
BOLTING
ASTM F467 UNS N06625
OPERATOR Gear operator 4, 9
MARKING MSS SP-25 7
INSPECTION & TESTS/
API 6D 1, 5
ACCEPTANCE
TESTING Charpy test No
Leak test Yes
Torque test Yes (As per section 6.5.1 in 200-20-PI-SPC-00006)
CERTIFICATIONS API 6D, EN 10204 Type 3.1
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 8
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves"
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification
200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A11A Notes
Offering
MATERIAL GROUP Group 2.2
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
Instrument Air Distribution, Demineralised Water, Portable Water Distribution,
SERVICE
Chemical Injection, Breathing Air, Nitrogen Generation & Distribution
TYPE Full Bore
DESIGN API 608 / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A182 F316/316L
BALL Floating Ball, Solid Ball ASTM A182 F316
SEAT Soft seat RPTFE 2
SEAT HOLDER ASTM A182 F316L
SEAT SPRING N/A
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM / TRUNNION Shouldered anti-blow out ASTM A182 F316
STEM SEAL Elastomeric / Grafoil 2
ASTM F468 UNS N06625
BOLTING
ASTM F467 UNS N06625
OPERATOR Lever operator 4
MARKING MSS SP-25 7
TESTING Charpy test No
Leak test Yes
Torque test NO
INSPECTION & TESTS/
API 598 1, 5
ACCEPTANCE
CERTIFICATIONS API 607, EN 10204 Type 3.1
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 8
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves"
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification
200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A11A Notes
Offering
MATERIAL GROUP Group 2.2
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
Instrument Air Distribution, Demineralised Water, Portable Water Distribution,
SERVICE
Chemical Injection, Breathing Air, Nitrogen Generation & Distribution
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A351 CF8M
BALL Floating Ball, Solid Ball ASTM A182 F316
SEAT Soft seat RPTFE 2
CAVITY VENT CONNECTION NO
SEAT HOLDER ASTM A182 F316L
SEAT SPRING N/A
BODY SEAL Primary Seal & Firesafe Secondary Seal AED type and suitable for service 2
STEM / TRUNNION Shouldered anti-blow out ASTM A182 F316
STEM SEAL Elastomeric / Grafoil 2
ASTM F468 UNS N06625
BOLTING
ASTM F467 UNS N06625
Lever Operator
OPERATOR 4
MARKING MSS SP-25 7
INSPECTION & TESTS/
API 6D 1, 5
ACCEPTANCE
TESTING Charpy test No
Leak test Yes
Torque test Yes (As per section 6.5.1 in 200-20-PI-SPC-00006)
CERTIFICATIONS API 6D, EN 10204 Type 3.1
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 8
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves"
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification
200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A11A Notes
Offering
MATERIAL GROUP Group 2.2
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
Instrument Air Distribution, Demineralised Water, Portable Water Distribution,
SERVICE
Chemical Injection, Breathing Air, Nitrogen Generation & Distribution
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A351 CF8M
BALL Floating Ball, Solid Ball ASTM A182 F316
SEAT Soft seat RPTFE 2
CAVITY VENT CONNECTION NO
SEAT HOLDER ASTM A182 F316L
SEAT SPRING N/A
BODY SEAL Primary Seal & Firesafe Secondary Seal AED type and suitable for service 2
STEM / TRUNNION Shouldered anti-blow out ASTM A182 F316
STEM SEAL Elastomeric / Grafoil 2
ASTM F468 UNS N06625
BOLTING
ASTM F467 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification
200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A11A Notes
Offering
MATERIAL GROUP Group 2.2
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
Instrument Air Distribution, Demineralised Water, Portable Water Distribution,
SERVICE
Chemical Injection, Breathing Air, Nitrogen Generation & Distribution
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A351 CF8M
BALL Trunnion Mounted Ball, Solid Ball ASTM A182 F316
SEAT Soft seat RPTFE 2
CAVITY VENT CONNECTION NO
SEAT HOLDER ASTM A182 F316L
SEAT SPRING INCONEL X750
BODY SEAL Primary Seal & Firesafe Secondary Seal AED type and suitable for service 2
STEM / TRUNNION Shouldered anti-blow out ASTM A182 F316
STEM SEAL Elastomeric / Grafoil 2
ASTM F468 UNS N06625
BOLTING
ASTM F467 UNS N06625
OPERATOR Gear operator 4, 9
MARKING MSS SP-25 7
INSPECTION & TESTS/
API 6D 1, 5
ACCEPTANCE
TESTING Charpy test No
Leak test Yes
Torque test Yes (As per section 6.5.1 in 200-20-PI-SPC-00006)
CERTIFICATIONS API 6D, EN 10204 Type 3.1
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 8
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves"
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valve shall be high-pressure closure tested and double isolation and bleed tested per API SPEC 6D. Testing shall be conducted with
air/nitrogen.Leakage shall be measured through the open bleed.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification
200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
11. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A19A Notes
Offering
MATERIAL GROUP Group 2.8
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE Air Compressor Package Outlet, Helifuel
TYPE Reduced Bore
DESIGN API 608 / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A19A Notes
Offering
MATERIAL GROUP Group 2.8
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE Air Compressor Package Outlet, Helifuel
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A19A Notes
Offering
MATERIAL GROUP Group 2.8
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE Air Compressor Package Outlet, Helifuel
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A19A Notes
Offering
MATERIAL GROUP Group 2.8
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE Air Compressor Package Outlet, Helifuel
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
11. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A19A Notes
Offering
MATERIAL GROUP Group 2.8
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE Air Compressor Package Outlet, Helifuel
TYPE Full Bore
DESIGN API 608 / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A19A Notes
Offering
MATERIAL GROUP Group 2.8
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE Air Compressor Package Outlet, Helifuel
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A19A Notes
Offering
MATERIAL GROUP Group 2.8
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE Air Compressor Package Outlet, Helifuel
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A19A Notes
Offering
MATERIAL GROUP Group 2.8
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE Air Compressor Package Outlet, Helifuel
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
11. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A33A Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE Hypochlorite
TYPE Reduced Bore
DESIGN API 608 / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A33A Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE Hypochlorite
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A33A Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE Hypochlorite
TYPE Full Bore
DESIGN API 608 / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A33A Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE Hypochlorite
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -29°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
SERVICE HP Flare, Liquid From HP Flare KO Drum(NACE)
TYPE Reduced Bore
DESIGN API 608 / ASME B16.34, EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -100°C to +175°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
SERVICE HP Flare, Liquid From HP Flare KO Drum(NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34, EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -100°C to +175°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A494 Gr.CW6MC
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
7.
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
SERVICE HP Flare, Liquid From HP Flare KO Drum(NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34, EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -100°C to +175°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A494 Gr.CW6MC
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
SERVICE HP Flare, Liquid From HP Flare KO Drum(NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34, EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -100°C to +175°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A494 Gr.CW6MC
BALL Trunnion Mounted Ball, Solid Ball ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
12. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 3
CORROSION ALLOWANCE 0 mm
SERVICE HP Flare, Liquid From HP Flare KO Drum(NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34, EEMUA 192 6
END TO END DIMENSION ASME B16.10 (Long Pattern) (Upto 36") / Manufacturer Standard (Size 38" and
STANDARD above)
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -100°C to +175°C
END CONNECTIONS Butt Weld Ends with Pup pieces to suit Pipe wall thickness 9,10
BODY / BONNET Top body ASTM A494 Gr. CW6MC
BALL Trunnion Mounted Ball, Solid Ball ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. Valve end wall thickness shall be as per ASME B16.25 to suit the following pipe wall thickness as mentioned in MTO description.
10. Valve shall be provided with body extensions (or) welded-on pipes of length as below to allow field welding and PWHT, if specified,without
disassembly, distortion (or) damage to non-metallic internals.
1) For valves NPS 14 to NPS 16: 400 mm
2) For valves ≥ NPS 18: 800 mm
The material of the extension shall be forged (or) cast as a part of the body or shall be ASTM B705 UNS N06625 Gr.1 CL.2, Welded, pipe
material.The body extension wall thickness shall be as per thickness mentioned in the MTO description. Pressure testing shall be performed after
welding and heat treatment.
11. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
13. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
SERVICE HP Flare, Liquid From HP Flare KO Drum(NACE)
TYPE Full Bore
DESIGN API 608 / ASME B16.34, EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -100°C to +175°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
SERVICE HP Flare, Liquid From HP Flare KO Drum(NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 / EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -100°C to +175°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A494 Gr.CW6MC
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
SERVICE HP Flare, Liquid From HP Flare KO Drum(NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 / EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -100°C to +175°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A494 Gr.CW6MC
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
SERVICE HP Flare, Liquid From HP Flare KO Drum(NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 / EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -100°C to +175°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A494 Gr.CW6MC
BALL Trunnion Mounted Ball, Solid Ball ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
12. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 3
CORROSION ALLOWANCE 0 mm
SERVICE HP Flare, Liquid From HP Flare KO Drum(NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34, EEMUA 192 6
END TO END DIMENSION ASME B16.10 (Long Pattern) (Upto 36") / Manufacturer Standard (Size 38" and
STANDARD above)
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -100°C to +175°C
END CONNECTIONS Butt Weld Ends with Pup pieces to suit Pipe wall thickness 9,10
BODY / BONNET Top body ASTM A494 Gr. CW6MC
BALL Trunnion Mounted Ball, Solid Ball ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. Valve end wall thickness shall be as per ASME B16.25 to suit the following pipe wall thickness as mentioned in MTO description.
10. Valve shall be provided with body extensions (or) welded-on pipes of length as below to allow field welding and PWHT, if specified,without
disassembly, distortion (or) damage to non-metallic internals.
1) For valves NPS 14 to NPS 16: 400 mm
2) For valves ≥ NPS 18: 800 mm
The material of the extension shall be forged (or) cast as a part of the body or shall be ASTM B705 UNS N06625 Gr.1 CL.2, Welded, pipe
material.The body extension wall thickness shall be as per thickness mentioned in the MTO description. Pressure testing shall be performed after
welding and heat treatment.
11. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
13. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A35B Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE Fire water (Dry system)
TYPE Reduced Bore
DESIGN Manufacturer Standard 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING 16 Barg
8
DESIGN TEMP. -29°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be suitable for FF rubber, Shore A50-70 Durometer hardness gasket (6.2-12.5μm average roughness).
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be 24 Bar
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Vendor to submit the Pressure- Temperature rating curve for the material for COMPANY approval as part of the offer.
9. Flange dimension and bolt holes to match ASME B16.5 Class 150 rating.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
12. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A35B Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE Fire water (Dry system)
TYPE Reduced Bore
DESIGN Manufacturer Standard 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING 16 Barg
8
DESIGN TEMP. -29°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be suitable for FF rubber, Shore A50-70 Durometer hardness gasket (6.2-12.5μm average roughness).
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be 24 Bar
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Vendor to submit the Pressure- Temperature rating curve for the material for COMPANY approval as part of the offer.
9. Flange dimension and bolt holes to match ASME B16.5 Class 150 rating.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
12. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A35B Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE Fire water (Dry system)
TYPE Reduced Bore
DESIGN Manufacturer Standard 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING 16 Barg
8
DESIGN TEMP. -29°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be suitable for FF rubber, Shore A50-70 Durometer hardness gasket (6.2-12.5μm average roughness).
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be 24 Bar
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Vendor to submit the Pressure- Temperature rating curve for the material for COMPANY approval as part of the offer.
9. Flange dimension and bolt holes to match ASME B16.5 Class 150 rating.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
14. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A35B Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE Fire water (Dry system)
TYPE Reduced Bore
DESIGN Manufacturer Standard 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING 16 Barg
8
DESIGN TEMP. -29°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be suitable for FF rubber, Shore A50-70 Durometer hardness gasket (6.2-12.5μm average roughness).
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be 24 Bar
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Vendor to submit the Pressure- Temperature rating curve for the material for COMPANY approval as part of the offer.
9. Flange dimension and bolt holes to match ASME B16.5 Class 150 rating.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
14. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
15. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A35B Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE Fire water (Dry system)
TYPE Full Bore
DESIGN Manufacturer Standard 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING 16 Barg
8
DESIGN TEMP. -29°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be suitable for FF rubber, Shore A50-70 Durometer hardness gasket (6.2-12.5μm average roughness).
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be 24 Bar
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Vendor to submit the Pressure- Temperature rating curve for the material for COMPANY approval as part of the offer.
9. Flange dimension and bolt holes to match ASME B16.5 Class 150 rating.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
12. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A35B Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE Fire water (Dry system)
TYPE Full Bore
DESIGN Manufacturer Standard 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING 16 Barg
8
DESIGN TEMP. -29°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be suitable for FF rubber, Shore A50-70 Durometer hardness gasket (6.2-12.5μm average roughness).
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be 24 Bar
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Vendor to submit the Pressure- Temperature rating curve for the material for COMPANY approval as part of the offer.
9. Flange dimension and bolt holes to match ASME B16.5 Class 150 rating.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
12. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A35B Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE Fire water (Dry system)
TYPE Full Bore
DESIGN Manufacturer Standard 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING 16 Barg
8
DESIGN TEMP. -29°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be suitable for FF rubber, Shore A50-70 Durometer hardness gasket (6.2-12.5μm average roughness).
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be 24 Bar
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Vendor to submit the Pressure- Temperature rating curve for the material for COMPANY approval as part of the offer.
9. Flange dimension and bolt holes to match ASME B16.5 Class 150 rating.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
14. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A35B Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE Fire water (Dry system)
TYPE Full Bore
DESIGN Manufacturer Standard 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING 16 Barg
8
DESIGN TEMP. -29°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be suitable for FF rubber, Shore A50-70 Durometer hardness gasket (6.2-12.5μm average roughness).
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be 24 Bar
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Vendor to submit the Pressure- Temperature rating curve for the material for COMPANY approval as part of the offer.
9. Flange dimension and bolt holes to match ASME B16.5 Class 150 rating.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
14. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
15. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
SERVICE Closed Drain Booster Pump, LP Flare (NACE)
TYPE Reduced Bore
DESIGN API 608 / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -46°C to +175°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
SERVICE Closed Drain Booster Pump, LP Flare (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -46°C to +175°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
SERVICE Closed Drain Booster Pump, LP Flare (NACE)
TYPE Full Bore
DESIGN API 608 / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -46°C to +175°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
SERVICE Closed Drain Booster Pump, LP Flare (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -46°C to +175°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A45B Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
Sea Water Lift & Distribution, Service Water Lift & Distribution, Fire Water,
SERVICE
Hazardous open Drain, Non Hazardous open Drain, Sewage Water Treatment
TYPE Reduced Bore
DESIGN Manufacturer Standard 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING 16 barg
10
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged FF to ASME B16.5 3,9
BODY / BONNET Split body ASTM B148 C95800 12
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be suitable for FF rubber, Shore A50-70 Durometer hardness gasket (6.2-12.5μm average roughness).
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be 24 Bar
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Flange dimension and bolt holes to match ASME B16.5 Class 150 rating.
10. Vendor to submit the Pressure- Temperature rating curve for the material for COMPANY approval as part of the offer.
11. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
12. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A45B Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
Sea Water Lift & Distribution, Service Water Lift & Distribution, Fire Water,
SERVICE
Hazardous open Drain, Non Hazardous open Drain, Sewage Water Treatment
TYPE Reduced Bore
DESIGN Manufacturer Standard 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING 16 barg
8
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged FF to ASME B16.5 3, 9
BODY / BONNET Split body ASTM B148 C95800 11
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be suitable for FF rubber, Shore A50-70 Durometer hardness gasket (6.2-12.5μm average roughness).
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be 24 Bar
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Vendor to submit the Pressure- Temperature rating curve for the material for COMPANY approval as part of the offer.
9. Flange dimension and bolt holes to match ASME B16.5 Class 150 rating.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
12. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A45B Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
Sea Water Lift & Distribution, Service Water Lift & Distribution, Fire Water,
SERVICE
Hazardous open Drain, Non Hazardous open Drain, Sewage Water Treatment
TYPE Reduced Bore
DESIGN Manufacturer Standard 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING 16 barg
8
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged FF to ASME B16.5 3, 9
BODY / BONNET Split body ASTM B148 C95800 11
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be suitable for FF rubber, Shore A50-70 Durometer hardness gasket (6.2-12.5μm average roughness).
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be 24 Bar
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Vendor to submit the Pressure- Temperature rating curve for the material for COMPANY approval as part of the offer.
9. Flange dimension and bolt holes to match ASME B16.5 Class 150 rating.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
14. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A45B Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
Sea Water Lift & Distribution, Service Water Lift & Distribution, Fire Water,
SERVICE
Hazardous open Drain, Non Hazardous open Drain, Sewage Water Treatment
TYPE Reduced Bore
DESIGN Manufacturer Standard 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING 16 barg
8
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged FF to ASME B16.5 3, 9
BODY / BONNET Split body ASTM B148 C95800 11
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be suitable for FF rubber, Shore A50-70 Durometer hardness gasket (6.2-12.5μm average roughness).
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be 24 Bar
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Vendor to submit the Pressure- Temperature rating curve for the material for COMPANY approval as part of the offer.
9. Flange dimension and bolt holes to match ASME B16.5 Class 150 rating.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
14. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
15. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A45B Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
Sea Water Lift & Distribution, Service Water Lift & Distribution, Fire Water,
SERVICE
Hazardous open Drain, Non Hazardous open Drain, Sewage Water Treatment
TYPE Full Bore
DESIGN Manufacturer Standard 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING 16 barg
9
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged FF to ASME B16.5 3,8
BODY / BONNET Split body ASTM B148 C95800 11
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be suitable for FF rubber, Shore A50-70 Durometer hardness gasket (6.2-12.5μm average roughness).
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be 24 Bar
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Flange dimension and bolt holes to match ASME B16.5 Class 150 rating.
9. Vendor to submit the Pressure- Temperature rating curve for the material for COMPANY approval as part of the offer.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
12. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A45B Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
Sea Water Lift & Distribution, Service Water Lift & Distribution, Fire Water,
SERVICE
Hazardous open Drain, Non Hazardous open Drain, Sewage Water Treatment
TYPE Full Bore
DESIGN Manufacturer Standard 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING 16 barg
8
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged FF to ASME B16.5 3, 9
BODY / BONNET Split body ASTM B148 C95800 11
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be suitable for FF rubber, Shore A50-70 Durometer hardness gasket (6.2-12.5μm average roughness).
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be 24 Bar
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Vendor to submit the Pressure- Temperature rating curve for the material for COMPANY approval as part of the offer.
9. Flange dimension and bolt holes to match ASME B16.5 Class 150 rating.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
12. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A45B Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
Sea Water Lift & Distribution, Service Water Lift & Distribution, Fire Water,
SERVICE
Hazardous open Drain, Non Hazardous open Drain, Sewage Water Treatment
TYPE Full Bore
DESIGN Manufacturer Standard 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING 16 barg
8
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged FF to ASME B16.5 3, 9
BODY / BONNET Split body ASTM B148 C95800 11
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be suitable for FF rubber, Shore A50-70 Durometer hardness gasket (6.2-12.5μm average roughness).
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be 24 Bar
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Vendor to submit the Pressure- Temperature rating curve for the material for COMPANY approval as part of the offer.
9. Flange dimension and bolt holes to match ASME B16.5 Class 150 rating.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
14. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS A45B Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
Sea Water Lift & Distribution, Service Water Lift & Distribution, Fire Water,
SERVICE
Hazardous open Drain, Non Hazardous open Drain, Sewage Water Treatment
TYPE Full Bore
DESIGN Manufacturer Standard 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING 16 barg
8
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged FF to ASME B16.5 3, 9
BODY / BONNET Split body ASTM B148 C95800 11
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be suitable for FF rubber, Shore A50-70 Durometer hardness gasket (6.2-12.5μm average roughness).
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be 24 Bar
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Vendor to submit the Pressure- Temperature rating curve for the material for COMPANY approval as part of the offer.
9. Flange dimension and bolt holes to match ASME B16.5 Class 150 rating.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
14. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
15. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS B1E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE Diesel From Supply Boat
TYPE Reduced Bore
DESIGN API 608 / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 300
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A105N 8
BALL Floating Ball, Solid Ball ASTM A182 Gr.F316
SEAT Soft seat RPTFE 2
SEAT HOLDER ASTM A182 Gr.F316L
SEAT SPRING N/A
BODY SEAL Primary Seal & Firesafe Secondary Seal AED type and suitable for service 2
STEM / TRUNNION Shouldered anti-blow out ASTM A182 Gr.F316
STEM SEAL Elastomeric / Grafoil 2
ASTM A193 B7 / ASTM A194 2H
BOLTING Alloy Steel 10
(Zn/Ni Plated + PTFE Coated)
OPERATOR Lever Operator 4
MARKING MSS SP-25 7
INSPECTION & TESTS/
API 598 1, 5
ACCEPTANCE
TESTING Charpy test Yes
Leak test Yes
Torque test NO
CERTIFICATIONS API 607, EN 10204 Type 3.1
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 9
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves"
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS B1E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE Diesel From Supply Boat
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 300
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A216 Gr WCB 8
BALL Floating Ball, Solid Ball ASTM A182 Gr.F316
SEAT Soft seat RPTFE 2
CAVITY VENT CONNECTION NO
SEAT HOLDER ASTM A182 Gr.F316L
SEAT SPRING N/A
BODY SEAL Primary Seal & Firesafe Secondary Seal AED type and suitable for service 2
STEM / TRUNNION Shouldered anti-blow out ASTM A182 Gr.F316
STEM SEAL Elastomeric / Grafoil 2
ASTM A193 B7 / ASTM A194 2H
BOLTING Alloy Steel 10
(Zn/Ni Plated + PTFE Coated)
OPERATOR Lever Operator 4
MARKING MSS SP-25 7
INSPECTION & TESTS/
API 6D 1, 5
ACCEPTANCE
TESTING Charpy test Yes
Leak test Yes
Torque test Yes (As per section 6.5.1 in 200-20-PI-SPC-00006)
CERTIFICATIONS API 6D, EN 10204 Type 3.1
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 9
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves"
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS B1E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE Diesel From Supply Boat
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 300
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A216 Gr WCB 8
BALL Floating Ball, Solid Ball ASTM A182 Gr.F316
SEAT Soft seat RPTFE 2
CAVITY VENT CONNECTION NO
SEAT HOLDER ASTM A182 Gr.F316L
SEAT SPRING N/A
BODY SEAL Primary Seal & Firesafe Secondary Seal AED type and suitable for service 2
STEM / TRUNNION Shouldered anti-blow out ASTM A182 Gr.F316
STEM SEAL Elastomeric / Grafoil 2
ASTM A193 B7 / ASTM A194 2H
BOLTING Alloy Steel 10
(Zn/Ni Plated + PTFE Coated)
OPERATOR Gear Operator 4, 11
MARKING MSS SP-25 7
INSPECTION & TESTS/
API 6D 1, 5
ACCEPTANCE
TESTING Charpy test Yes
Leak test Yes
Torque test Yes (As per section 6.5.1 in 200-20-PI-SPC-00006)
CERTIFICATIONS API 6D, EN 10204 Type 3.1
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 9
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves"
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS B1E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE Diesel From Supply Boat
TYPE Full Bore
DESIGN API 608 / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 300
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A105N 8
BALL Floating Ball, Solid Ball ASTM A182 Gr.F316
SEAT Soft seat RPTFE 2
SEAT HOLDER ASTM A182 Gr.F316L
SEAT SPRING N/A
BODY SEAL Primary Seal & Firesafe Secondary Seal AED type and suitable for service 2
STEM / TRUNNION Shouldered anti-blow out ASTM A182 Gr.F316
STEM SEAL Elastomeric / Grafoil 2
ASTM A193 B7 / ASTM A194 2H
BOLTING Alloy Steel 10
(Zn/Ni Plated + PTFE Coated)
OPERATOR Lever Operator 4
MARKING MSS SP-25 7
INSPECTION & TESTS/
API 598 1, 5
ACCEPTANCE
TESTING Charpy test Yes
Leak test Yes
Torque test NO
CERTIFICATIONS API 607, EN 10204 Type 3.1
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 9
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves"
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS B1E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE Diesel From Supply Boat
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 300
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A216 Gr WCB 8
BALL Floating Ball, Solid Ball ASTM A182 Gr.F316
SEAT Soft seat RPTFE 2
CAVITY VENT CONNECTION NO
SEAT HOLDER ASTM A182 Gr.F316L
SEAT SPRING N/A
BODY SEAL Primary Seal & Firesafe Secondary Seal AED type and suitable for service 2
STEM / TRUNNION Shouldered anti-blow out ASTM A182 Gr.F316
STEM SEAL Elastomeric / Grafoil 2
ASTM A193 B7 / ASTM A194 2H
BOLTING Alloy Steel 10
(Zn/Ni Plated + PTFE Coated)
OPERATOR Lever Operator 4
MARKING MSS SP-25 7
INSPECTION & TESTS/
API 6D 1, 5
ACCEPTANCE
TESTING Charpy test Yes
Leak test Yes
Torque test Yes (As per section 6.5.1 in 200-20-PI-SPC-00006)
CERTIFICATIONS API 6D, EN 10204 Type 3.1
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 9
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves"
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS B1E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE Diesel From Supply Boat
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 300
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A216 Gr WCB 8
BALL Floating Ball, Solid Ball ASTM A182 Gr.F316
SEAT Soft seat RPTFE 2
CAVITY VENT CONNECTION NO
SEAT HOLDER ASTM A182 Gr.F316L
SEAT SPRING N/A
BODY SEAL Primary Seal & Firesafe Secondary Seal AED type and suitable for service 2
STEM / TRUNNION Shouldered anti-blow out ASTM A182 Gr.F316
STEM SEAL Elastomeric / Grafoil 2
ASTM A193 B7 / ASTM A194 2H
BOLTING Alloy Steel 10
(Zn/Ni Plated + PTFE Coated)
OPERATOR Gear Operator 4, 11
MARKING MSS SP-25 7
INSPECTION & TESTS/
API 6D 1, 5
ACCEPTANCE
TESTING Charpy test Yes
Leak test Yes
Torque test Yes (As per section 6.5.1 in 200-20-PI-SPC-00006)
CERTIFICATIONS API 6D, EN 10204 Type 3.1
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 9
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves"
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS B6E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Cooling Water Circulation (To Inlet Cooler and Discharge Cooler) (NACE)
TYPE Reduced Bore
DESIGN API 608 / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 300
DESIGN TEMP. -29°C to +180°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A105N 8
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS B6E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Cooling Water Circulation (To Inlet Cooler and Discharge Cooler) (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 300
DESIGN TEMP. -29°C to +180°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A216 Gr WCB 8
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS B6E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Cooling Water Circulation (To Inlet Cooler and Discharge Cooler) (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 300
DESIGN TEMP. -29°C to +180°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A216 Gr WCB 8
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS B6E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Cooling Water Circulation (To Inlet Cooler and Discharge Cooler) (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 300
DESIGN TEMP. -29°C to +180°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A216 Gr WCB 8
BALL Trunnion Mounted Ball, Solid Ball ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification
200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
14. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS B6E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Cooling Water Circulation (To Inlet Cooler and Discharge Cooler) (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern) (Upto 36") / Manufacturer Standard (Size 38" and above)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 300
DESIGN TEMP. -29°C to +180°C
END CONNECTIONS Butt Weld Ends with Pup pieces to suit Pipe wall thickness 3,12
BODY / BONNET Top Body ASTM A216 Gr WCB 8
BALL Trunnion Mounted Ball, Solid Ball ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or
deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3 Valve end wall thickness shall be as per ASME B16.25 to suit the following pipe wall thickness as mentioned in MTO description.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable for
Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12 Valve shall be provided with 800MM body extensions (or) welded-on pipes to allow field welding and PWHT, if specified,without disassembly,
distortion (or) damage to non-metallic internals. The material of the extension shall be forged (or) cast as a part of the body or shall be A672 Gr.B60
Cl.22, EFW pipe material.The body extension wall thickness shall be as per thickness mentioned in the MTO description. Pressure testing shall be
performed after welding and heat treatment.
13. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
14. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
15. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS B6E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Cooling Water Circulation (To Inlet Cooler and Discharge Cooler) (NACE)
TYPE Full Bore
DESIGN API 608 / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 300
DESIGN TEMP. -29°C to +180°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A105N 8
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS B6E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Cooling Water Circulation (To Inlet Cooler and Discharge Cooler) (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 300
DESIGN TEMP. -29°C to +180°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A216 Gr WCB 8
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS B6E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Cooling Water Circulation (To Inlet Cooler and Discharge Cooler) (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 300
DESIGN TEMP. -29°C to +180°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A216 Gr WCB 8
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS B6E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Cooling Water Circulation (To Inlet Cooler and Discharge Cooler) (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 300
DESIGN TEMP. -29°C to +180°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A216 Gr WCB 8
BALL Trunnion Mounted Ball, Solid Ball ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
14. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS B6E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 3
CORROSION ALLOWANCE 3 mm
SERVICE Cooling Water Circulation (To Inlet Cooler and Discharge Cooler) (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern) (Upto 36") / Manufacturer Standard (Size 38" and above)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 300
DESIGN TEMP. -29°C to +180°C
END CONNECTIONS Butt Weld Ends with Pup pieces to suit Pipe wall thickness 11, 12
BODY / BONNET Top Body ASTM A216 Gr WCB 8
BALL Trunnion Mounted Ball, Solid Ball ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or
deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable for
Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. Valve end wall thickness shall be as per ASME B16.25 to suit the following pipe wall thickness as mentioned in MTO description.
12 Valve shall be provided with 800MM body extensions (or) welded-on pipes to allow field welding and PWHT, if specified,without disassembly,
distortion (or) damage to non-metallic internals. The material of the extension shall be forged (or) cast as a part of the body or shall be A672 Gr.B60
Cl.22, EFW pipe material.The body extension wall thickness shall be as per thickness mentioned in the MTO description. Pressure testing shall be
performed after welding and heat treatment.
13. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
14. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
15. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS B19A Notes
Offering
MATERIAL GROUP Group 2.8
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE Fuel Gas to GTG
TYPE Reduced Bore
DESIGN API 608 / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 300
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS B19A Notes
Offering
MATERIAL GROUP Group 2.8
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE Fuel Gas to GTG
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 300
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS B19A Notes
Offering
MATERIAL GROUP Group 2.8
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE Fuel Gas to GTG
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 300
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS B19A Notes
Offering
MATERIAL GROUP Group 2.8
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE Fuel Gas to GTG
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 300
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
11. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS B19A Notes
Offering
MATERIAL GROUP Group 2.8
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE Fuel Gas to GTG
TYPE Full Bore
DESIGN API 608 / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 300
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS B19A Notes
Offering
MATERIAL GROUP Group 2.8
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE Fuel Gas to GTG
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 300
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS B19A Notes
Offering
MATERIAL GROUP Group 2.8
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE Fuel Gas to GTG
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 300
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS B19A Notes
Offering
MATERIAL GROUP Group 2.8
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE Fuel Gas to GTG
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 300
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
11. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS B34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
High pressure Flare Piping (Short segment BDV/PSV) & Isolation (FG-300#)
SERVICE
(NACE)
TYPE Reduced Bore
DESIGN API 608 / ASME B16.34, EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 300
DESIGN TEMP. -100°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS B34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
High pressure Flare Piping (Short segment BDV/PSV) & Isolation (FG-300#)
SERVICE
(NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34, EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 300
DESIGN TEMP. -100°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A494 Gr. CW6MC
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS B34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
High pressure Flare Piping (Short segment BDV/PSV) & Isolation (FG-300#)
SERVICE
(NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34, EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 300
DESIGN TEMP. -100°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A494 Gr. CW6MC
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS B34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
High pressure Flare Piping (Short segment BDV/PSV) & Isolation (FG-300#)
SERVICE
(NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34, EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 300
DESIGN TEMP. -100°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A494 Gr. CW6MC
BALL Trunnion Mounted Ball, Solid Ball ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
12. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS B34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 3
CORROSION ALLOWANCE 0 mm
High pressure Flare Piping (Short segment BDV/PSV) & Isolation (FG-300#)
SERVICE
(NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34, EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 300
DESIGN TEMP. -100°C to +85°C
END CONNECTIONS Butt Weld Ends with Pup pieces to suit Pipe wall thickness 9,10
BODY / BONNET Top body ASTM A494 Gr. CW6MC
BALL Trunnion Mounted Ball, Solid Ball ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. Valve end wall thickness shall be as per ASME B16.25 to suit the following pipe wall thickness as mentioned in MTO description.
10. Valve shall be provided with body extensions (or) welded-on pipes of length as below to allow field welding and PWHT, if specified,without
disassembly, distortion (or) damage to non-metallic internals.
1) For valves NPS 14 to NPS 16: 400 mm
2) For valves ≥ NPS 18: 800 mm
The material of the extension shall be forged (or) cast as a part of the body or shall be ASTM B705 UNS N06625 Gr.1 CL.2, Welded, pipe
material.The body extension wall thickness shall be as per thickness mentioned in the MTO description. Pressure testing shall be performed after
welding and heat treatment.
11. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
13. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS B34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
High pressure Flare Piping (Short segment BDV/PSV) & Isolation (FG-300#)
SERVICE
(NACE)
TYPE Full Bore
DESIGN API 608 / ASME B16.34, EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 300
DESIGN TEMP. -100°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS B34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
High pressure Flare Piping (Short segment BDV/PSV) & Isolation (FG-300#)
SERVICE
(NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34, EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 300
DESIGN TEMP. -100°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A494 Gr. CW6MC
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS B34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
High pressure Flare Piping (Short segment BDV/PSV) & Isolation (FG-300#)
SERVICE
(NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34, EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 300
DESIGN TEMP. -100°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A494 Gr. CW6MC
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS B34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
High pressure Flare Piping (Short segment BDV/PSV) & Isolation (FG-300#)
SERVICE
(NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34, EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 300
DESIGN TEMP. -100°C to +85°C
END CONNECTIONS Flanged RF to ASME B16.5 3
BODY / BONNET Split body ASTM A494 Gr. CW6MC
BALL Trunnion Mounted Ball, Solid Ball ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
12. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS B34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 3
CORROSION ALLOWANCE 0 mm
High pressure Flare Piping (Short segment BDV/PSV) & Isolation (FG-300#)
SERVICE
(NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34, EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 300
DESIGN TEMP. -100°C to +85°C
END CONNECTIONS Butt Weld Ends with Pup pieces to suit Pipe wall thickness 9,10
BODY / BONNET Top body ASTM A494 Gr. CW6MC
BALL Trunnion Mounted Ball, Solid Ball ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. Valve end wall thickness shall be as per ASME B16.25 to suit the following pipe wall thickness as mentioned in MTO description.
10. Valve shall be provided with body extensions (or) welded-on pipes of length as below, to allow field welding and PWHT, if specified,without
disassembly, distortion (or) damage to non-metallic internals.
1) For valves NPS 14 to NPS 16: 400 mm
2) For valves ≥ NPS 18: 800 mm
The material of the extension shall be forged (or) cast as a part of the body or shall be ASTM B705 UNS N06625 Gr.1 CL.2, Welded, pipe
material.The body extension wall thickness shall be as per thickness mentioned in the MTO description. Pressure testing shall be performed after
welding and heat treatment.
11. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
13. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS D5E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE Topside Fuel Gas Upstream Filter
TYPE Reduced Bore
DESIGN API 608 / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 600
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS D5E Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE Topside Fuel Gas Upstream Filter
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 600
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
12. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS D5E Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE Topside Fuel Gas Upstream Filter
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 600
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
13. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS D5E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE Topside Fuel Gas Upstream Filter
TYPE Full Bore
DESIGN API 608 / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 600
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS D5E Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE Topside Fuel Gas Upstream Filter
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 600
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
12. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS D5E Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE Topside Fuel Gas Upstream Filter
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 600
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
13. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS D7E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
TYPE Reduced Bore
DESIGN API 608 / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 600
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS D7E Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 600
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
13. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS D7E Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 600
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
14. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS D7E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
TYPE Full Bore
DESIGN API 608 / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 600
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS D7E Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 600
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
13. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS D7E Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 600
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
14. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS D19A Notes
Offering
MATERIAL GROUP Group 2.8
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE HP Fuel Gas to GTG
TYPE Reduced Bore
DESIGN API 608 / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 600
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS D19A Notes
Offering
MATERIAL GROUP Group 2.8
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE HP Fuel Gas to GTG
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 600
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
10. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS D19A Notes
Offering
MATERIAL GROUP Group 2.8
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE HP Fuel Gas to GTG
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 600
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
11. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS D19A Notes
Offering
MATERIAL GROUP Group 2.8
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE HP Fuel Gas to GTG
TYPE Full Bore
DESIGN API 608 / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 600
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS D19A Notes
Offering
MATERIAL GROUP Group 2.8
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE HP Fuel Gas to GTG
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 600
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
10. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS D19A Notes
Offering
MATERIAL GROUP Group 2.8
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE HP Fuel Gas to GTG
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 600
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
11. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS D34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
SERVICE High Pressure Flare Piping (Short Segment BDV/PSV) & Isolation (FG-600#) (NACE)
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS D34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
SERVICE High Pressure Flare Piping (Short Segment BDV/PSV) & Isolation (FG-600#) (NACE)
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
11. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS D34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
SERVICE High Pressure Flare Piping (Short Segment BDV/PSV) & Isolation (FG-600#) (NACE)
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
12. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS D34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 3
CORROSION ALLOWANCE 0 mm
SERVICE High Pressure Flare Piping (Short Segment BDV/PSV) & Isolation (FG-600#) (NACE)
END CONNECTIONS Butt Weld Ends with Pup pieces to suit Pipe wall thickness 9,10
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. Valve end wall thickness shall be as per ASME B16.25 to suit the following pipe wall thickness as mentioned in MTO description.
10. Valve shall be provided with body extensions (or) welded-on pipes of length as below, to allow field welding and PWHT, if specified,without
disassembly, distortion (or) damage to non-metallic internals.
1) For valves NPS 14 to NPS 16: 400 mm
2) For valves ≥ NPS 18: 800 mm
The material of the extension shall be forged (or) cast as a part of the body or shall be ASTM B705 UNS N06625 Gr.1 CL.2, Welded, pipe
material.The body extension wall thickness shall be as per thickness mentioned in the MTO description. Pressure testing shall be performed after
welding and heat treatment.
11. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
13. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS D34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
SERVICE High Pressure Flare Piping (Short Segment BDV/PSV) & Isolation (FG-600#) (NACE)
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS D34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
SERVICE High Pressure Flare Piping (Short Segment BDV/PSV) & Isolation (FG-600#) (NACE)
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
11. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS D34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
SERVICE High Pressure Flare Piping (Short Segment BDV/PSV) & Isolation (FG-600#) (NACE)
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
12. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS D34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 3
CORROSION ALLOWANCE 0 mm
SERVICE High Pressure Flare Piping (Short Segment BDV/PSV) & Isolation (FG-600#) (NACE)
END CONNECTIONS Butt Weld Ends with Pup pieces to suit Pipe wall thickness 9,10
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. Valve end wall thickness shall be as per ASME B16.25 to suit the following pipe wall thickness as mentioned in MTO description.
10. Valve shall be provided with body extensions (or) welded-on pipes of length as below, to allow field welding and PWHT, if specified,without
disassembly, distortion (or) damage to non-metallic internals.
1) For valves NPS 14 to NPS 16: 400 mm
2) For valves ≥ NPS 18: 800 mm
The material of the extension shall be forged (or) cast as a part of the body or shall be ASTM B705 UNS N06625 Gr.1 CL.2, Welded, pipe
material.The body extension wall thickness shall be as per thickness mentioned in the MTO description. Pressure testing shall be performed after
welding and heat treatment.
11. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
13. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS E5E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE Fuel Gas
TYPE Reduced Bore
DESIGN API 608 / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS E5E Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE Fuel Gas
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
12. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS E5E Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE Fuel Gas
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 900
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
12. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS E5E Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE Fuel Gas
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 900
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
13. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS E5E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE Fuel Gas
TYPE Full Bore
DESIGN API 608 / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS E5E Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE Fuel Gas
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
12. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS E5E Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE Fuel Gas
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 900
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
12. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS E5E Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE Fuel Gas
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 900
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
13. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS E7E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
TYPE Reduced Bore
DESIGN API 608 / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS E7E Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
13. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS E7E Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 900
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
13. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS E7E Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 900
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
14. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS E7E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
TYPE Full Bore
DESIGN API 608 / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS E7E Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
13. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS E7E Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 900
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
13. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS E7E Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 900
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
14. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS E34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Blow Down High Pressure Flare Piping (short segment BDV to Isolation valve) FG -
SERVICE
900#) (NACE)
TYPE Reduced Bore
DESIGN ASME B16.34, EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -100°C to +94°C
END CONNECTIONS Flanged RTJ to ASME B16.5 3
BODY / BONNET Split body ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS E34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Blow Down High Pressure Flare Piping (short segment BDV to Isolation valve) FG -
SERVICE
900#) (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34, EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -100°C to +94°C
END CONNECTIONS Flanged RTJ to ASME B16.5 3
BODY / BONNET Split body ASTM A494 Gr. CW6MC
BALL Trunnion Mounted Ball, Solid Ball ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
11. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS E34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Blow Down High Pressure Flare Piping (short segment BDV to Isolation valve) FG -
SERVICE
900#) (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34, EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 900
DESIGN TEMP. -100°C to +94°C
END CONNECTIONS Flanged RTJ to ASME B16.5 3
BODY / BONNET Split body ASTM A494 Gr. CW6MC
BALL Trunnion Mounted Ball, Solid Ball ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
11. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS E34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Blow Down High Pressure Flare Piping (short segment BDV to Isolation valve) FG -
SERVICE
900#) (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34, EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 900
DESIGN TEMP. -100°C to +94°C
END CONNECTIONS Flanged RTJ to ASME B16.5 3
BODY / BONNET Split body ASTM A494 Gr. CW6MC
BALL Trunnion Mounted Ball, Solid Ball ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
12. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS E34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 3
CORROSION ALLOWANCE 0 mm
Blow Down High Pressure Flare Piping (short segment BDV to Isolation valve) FG -
SERVICE
900#) (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34, EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 900
DESIGN TEMP. -100°C to +94°C
END CONNECTIONS Butt Weld Ends with Pup pieces to suit Pipe wall thickness 9,10
BODY / BONNET Top body ASTM A494 Gr. CW6MC
BALL Trunnion Mounted Ball, Solid Ball ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. Valve end wall thickness shall be as per ASME B16.25 to suit the following pipe wall thickness as mentioned in MTO description.
10. Valve shall be provided with body extensions (or) welded-on pipes of length as below, to allow field welding and PWHT, if specified,without
disassembly, distortion (or) damage to non-metallic internals.
1) For valves NPS 14 to NPS 16: 400 mm
2) For valves ≥ NPS 18: 800 mm
The material of the extension shall be forged (or) cast as a part of the body or shall be ASTM B705 UNS N06625 Gr.1 CL.2, Welded, pipe
material.The body extension wall thickness shall be as per thickness mentioned in the MTO description. Pressure testing shall be performed after
welding and heat treatment.
11. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
13. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS E34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Blow Down High Pressure Flare Piping (short segment BDV to Isolation valve) FG -
SERVICE
900#) (NACE)
TYPE Full Bore
DESIGN ASME B16.34, EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -100°C to +94°C
END CONNECTIONS Flanged RTJ to ASME B16.5 3
BODY / BONNET Split body ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS E34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Blow Down High Pressure Flare Piping (short segment BDV to Isolation valve) FG -
SERVICE
900#) (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34, EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -100°C to +94°C
END CONNECTIONS Flanged RTJ to ASME B16.5 3
BODY / BONNET Split body ASTM A494 Gr. CW6MC
BALL Trunnion Mounted Ball, Solid Ball ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
11. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS E34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Blow Down High Pressure Flare Piping (short segment BDV to Isolation valve) FG -
SERVICE
900#) (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34, EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 900
DESIGN TEMP. -100°C to +94°C
END CONNECTIONS Flanged RTJ to ASME B16.5 3
BODY / BONNET Split body ASTM A494 Gr. CW6MC
BALL Trunnion Mounted Ball, Solid Ball ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
11. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS E34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Blow Down High Pressure Flare Piping (short segment BDV to Isolation valve) FG -
SERVICE
900#) (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34, EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 900
DESIGN TEMP. -100°C to +94°C
END CONNECTIONS Flanged RTJ to ASME B16.5 3
BODY / BONNET Split body ASTM A494 Gr. CW6MC
BALL Trunnion Mounted Ball, Solid Ball ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
12. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS E34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 3
CORROSION ALLOWANCE 0 mm
Blow Down High Pressure Flare Piping (short segment BDV to Isolation valve) FG -
SERVICE
900#) (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34, EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 900
DESIGN TEMP. -100°C to +94°C
END CONNECTIONS Butt Weld Ends with Pup pieces to suit Pipe wall thickness 9,10
BODY / BONNET Top body ASTM A494 Gr. CW6MC
BALL Trunnion Mounted Ball, Solid Ball ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. Valve end wall thickness shall be as per ASME B16.25 to suit the following pipe wall thickness as mentioned in MTO description.
10. Valve shall be provided with body extensions (or) welded-on pipes of length as below, to allow field welding and PWHT, if specified,without
disassembly, distortion (or) damage to non-metallic internals.
1) For valves NPS 14 to NPS 16: 400 mm
2) For valves ≥ NPS 18: 800 mm
The material of the extension shall be forged (or) cast as a part of the body or shall be ASTM B705 UNS N06625 Gr.1 CL.2, Welded, pipe
material.The body extension wall thickness shall be as per thickness mentioned in the MTO description. Pressure testing shall be performed after
welding and heat treatment.
11. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
13. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS E37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
FWS to Inlet Seperator, Gas from Inlet Seperator / Copm. Suction Scrubber, Gas
from CP1S(RL) Comp.Discharge Cooler to RT/RT2/PU Platform, Liquid from Inlet
SERVICE
Seperator up to booster Pump Discharge, Comp. Suction Scrubber Pump Discharge,
Diesel for Valve Flushing, EG for Valve Flushing (NACE)
TYPE Reduced Bore
DESIGN ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -46°C to +94°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS E37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
FWS to Inlet Seperator, Gas from Inlet Seperator / Copm. Suction Scrubber, Gas
from CP1S(RL) Comp.Discharge Cooler to RT/RT2/PU Platform, Liquid from Inlet
SERVICE
Seperator up to booster Pump Discharge, Comp. Suction Scrubber Pump Discharge,
Diesel for Valve Flushing, EG for Valve Flushing (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -46°C to +94°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
11. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS E37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
FWS to Inlet Seperator, Gas from Inlet Seperator / Copm. Suction Scrubber, Gas
from CP1S(RL) Comp.Discharge Cooler to RT/RT2/PU Platform, Liquid from Inlet
SERVICE
Seperator up to booster Pump Discharge, Comp. Suction Scrubber Pump
Discharge, Diesel for Valve Flushing, EG for Valve Flushing (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 900
DESIGN TEMP. -46°C to +94°C
BALL Trunnion mounted Ball, Solid Ball ASTM B564 UNS N06625
SEAT Soft seat PEEK 2
CAVITY VENT CONNECTION NO
SEAT HOLDER ASTM B564 UNS N06625
SEAT SPRING INCONEL X750
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM / TRUNNION Shouldered anti-blow out UNS N07718
STEM SEAL Elastomeric / Grafoil 2
ASTM F468 UNS N06625
BOLTING Alloy Steel
ASTM F467 UNS N06625
OPERATOR Lever Operator 4
MARKING MSS SP-25 7
TESTING Charpy test No
Leak test Yes
Torque test Yes (As per section 6.5.1 in 200-20-PI-SPC-00006)
INSPECTION & TESTS/
API 6D 1, 5
ACCEPTANCE
CERTIFICATIONS API 6D, EN 10204 Type 3.2
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 8
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves"
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
11. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS E37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
FWS to Inlet Seperator, Gas from Inlet Seperator / Copm. Suction Scrubber, Gas
from CP1S(RL) Comp.Discharge Cooler to RT/RT2/PU Platform, Liquid from Inlet
SERVICE
Seperator up to booster Pump Discharge, Comp. Suction Scrubber Pump Discharge,
Diesel for Valve Flushing, EG for Valve Flushing (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 900
DESIGN TEMP. -46°C to +94°C
BALL Trunnion mounted Ball, Solid Ball ASTM B564 UNS N06625
SEAT Soft seat PEEK 2
CAVITY VENT CONNECTION NO
SEAT HOLDER ASTM B564 UNS N06625
SEAT SPRING INCONEL X750
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM / TRUNNION Shouldered anti-blow out UNS N07718
STEM SEAL Elastomeric / Grafoil 2
ASTM F468 UNS N06625
BOLTING Alloy Steel
ASTM F467 UNS N06625
OPERATOR Gear Operator 4, 10
MARKING MSS SP-25 7
TESTING Charpy test No
Leak test Yes
Torque test Yes (As per section 6.5.1 in 200-20-PI-SPC-00006)
INSPECTION & TESTS/
API 6D 1, 5
ACCEPTANCE
CERTIFICATIONS API 6D, EN 10204 Type 3.2
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 8
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves"
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
12. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS E37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
FWS to Inlet Seperator, Gas from Inlet Seperator / Copm. Suction Scrubber, Gas
from CP1S(RL) Comp.Discharge Cooler to RT/RT2/PU Platform, Liquid from Inlet
SERVICE
Seperator up to booster Pump Discharge, Comp. Suction Scrubber Pump Discharge,
Diesel for Valve Flushing, EG for Valve Flushing (NACE)
TYPE Full Bore
DESIGN ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -46°C to +94°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS E37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
FWS to Inlet Seperator, Gas from Inlet Seperator / Copm. Suction Scrubber, Gas
from CP1S(RL) Comp.Discharge Cooler to RT/RT2/PU Platform, Liquid from Inlet
SERVICE
Seperator up to booster Pump Discharge, Comp. Suction Scrubber Pump Discharge,
Diesel for Valve Flushing, EG for Valve Flushing (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -46°C to +94°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
11. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS E37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
FWS to Inlet Seperator, Gas from Inlet Seperator / Copm. Suction Scrubber, Gas
from CP1S(RL) Comp.Discharge Cooler to RT/RT2/PU Platform, Liquid from Inlet
SERVICE
Seperator up to booster Pump Discharge, Comp. Suction Scrubber Pump
Discharge, Diesel for Valve Flushing, EG for Valve Flushing (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 900
DESIGN TEMP. -46°C to +94°C
BALL Trunnion mounted Ball, Solid Ball ASTM B564 UNS N06625
SEAT Soft seat PEEK 2
CAVITY VENT CONNECTION NO
SEAT HOLDER ASTM B564 UNS N06625
SEAT SPRING INCONEL X750
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM / TRUNNION Shouldered anti-blow out UNS N07718
STEM SEAL Elastomeric / Grafoil 2
ASTM F468 UNS N06625
BOLTING Alloy Steel
ASTM F467 UNS N06625
OPERATOR Lever Operator 4
MARKING MSS SP-25 7
TESTING Charpy test No
Leak test Yes
Torque test Yes (As per section 6.5.1 in 200-20-PI-SPC-00006)
INSPECTION & TESTS/
API 6D 1, 5
ACCEPTANCE
CERTIFICATIONS API 6D, EN 10204 Type 3.2
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 8
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves"
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
11. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS E37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
FWS to Inlet Seperator, Gas from Inlet Seperator / Copm. Suction Scrubber, Gas
from CP1S(RL) Comp.Discharge Cooler to RT/RT2/PU Platform, Liquid from Inlet
SERVICE
Seperator up to booster Pump Discharge, Comp. Suction Scrubber Pump Discharge,
Diesel for Valve Flushing, EG for Valve Flushing (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 900
DESIGN TEMP. -46°C to +94°C
BALL Trunnion mounted Ball, Solid Ball ASTM B564 UNS N06625
SEAT Soft seat PEEK 2
CAVITY VENT CONNECTION NO
SEAT HOLDER ASTM B564 UNS N06625
SEAT SPRING INCONEL X750
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM / TRUNNION Shouldered anti-blow out UNS N07718
STEM SEAL Elastomeric / Grafoil 2
ASTM F468 UNS N06625
BOLTING Alloy Steel
ASTM F467 UNS N06625
OPERATOR Gear Operator 4, 10
MARKING MSS SP-25 7
TESTING Charpy test No
Leak test Yes
Torque test Yes (As per section 6.5.1 in 200-20-PI-SPC-00006)
INSPECTION & TESTS/
API 6D 1, 5
ACCEPTANCE
CERTIFICATIONS API 6D, EN 10204 Type 3.2
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 8
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves"
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
12. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F7E1 Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
TYPE Reduced Bore
DESIGN ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -46°C to +85°C
END CONNECTIONS Flanged RTJ to ASME B16.5 3
BODY / BONNET Split body ASTM A350 LF2 Cl.1 8
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F7E1 Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -46°C to +85°C
END CONNECTIONS Flanged RTJ to ASME B16.5 3
BODY / BONNET Split body ASTM A352 Gr LCC 8
BALL Trunnion Mounted Ball, Solid Ball ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification
200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-
00003 - Material Requirements for Sour Service
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
13. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F7E1 Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -46°C to +85°C
END CONNECTIONS Flanged RTJ to ASME B16.5 3
BODY / BONNET Split body ASTM A352 Gr LCC 8
BALL Trunnion Mounted Ball, Solid Ball ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification
200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
14. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F7E1 Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
TYPE Full Bore
DESIGN ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -46°C to +85°C
END CONNECTIONS Flanged RTJ to ASME B16.5 3
BODY / BONNET Split body ASTM A350 LF2 Cl.1 8
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F7E1 Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -46°C to +85°C
END CONNECTIONS Flanged RTJ to ASME B16.5 3
BODY / BONNET Split body ASTM A352 Gr LCC 8
BALL Trunnion Mounted Ball, Solid Ball ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification
200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-
00003 - Material Requirements for Sour Service
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
13. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F7E1 Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -46°C to +85°C
END CONNECTIONS Flanged RTJ to ASME B16.5 3
BODY / BONNET Split body ASTM A352 Gr LCC 8
BALL Trunnion Mounted Ball, Solid Ball ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification
200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
14. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F11A Notes
Offering
MATERIAL GROUP Group 2.2
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE EG Flushing, Breathing Air
TYPE Reduced Bore
DESIGN ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged RTJ to ASME B16.5 3
BODY / BONNET Split body ASTM A182 F316/316L
BALL Floating Ball, Solid Ball ASTM A182 F316
SEAT Soft seat PEEK 2
SEAT HOLDER ASTM A182 F316L
SEAT SPRING N/A
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM / TRUNNION Shouldered anti-blow out ASTM A182 F316
STEM SEAL Elastomeric / Grafoil 2
ASTM F468 UNS N06625
BOLTING
ASTM F467 UNS N06625
Lever Operator
OPERATOR 4
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification
200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F11A Notes
Offering
MATERIAL GROUP Group 2.2
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE EG Flushing, Breathing Air
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged RTJ to ASME B16.5 3
BODY / BONNET Split body ASTM A351 CF8M
BALL Trunnion Mounted Ball, Solid Ball ASTM A182 F316
SEAT Soft seat PEEK 2
CAVITY VENT CONNECTION NO
SEAT HOLDER ASTM A182 F316L
SEAT SPRING INCONEL X750
BODY SEAL Primary Seal & Firesafe Secondary Seal AED type and suitable for service 2
STEM / TRUNNION Shouldered anti-blow out ASTM A182 F316
STEM SEAL Elastomeric / Grafoil 2
ASTM F468 UNS N06625
BOLTING
ASTM F467 UNS N06625
Lever Operator
OPERATOR 4
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification
200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
10. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F11A Notes
Offering
MATERIAL GROUP Group 2.2
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE EG Flushing, Breathing Air
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged RTJ to ASME B16.5 3
BODY / BONNET Split body ASTM A351 CF8M
BALL Trunnion Mounted Ball, Solid Ball ASTM A182 F316
SEAT Soft seat PEEK 2
CAVITY VENT CONNECTION NO
SEAT HOLDER ASTM A182 F316L
SEAT SPRING INCONEL X750
BODY SEAL Primary Seal & Firesafe Secondary Seal AED type and suitable for service 2
STEM / TRUNNION Shouldered anti-blow out ASTM A182 F316
STEM SEAL Elastomeric / Grafoil 2
ASTM F468 UNS N06625
BOLTING
ASTM F467 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification
200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
11. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F11A Notes
Offering
MATERIAL GROUP Group 2.2
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE EG Flushing, Breathing Air
TYPE Full Bore
DESIGN ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged RTJ to ASME B16.5 3
BODY / BONNET Split body ASTM A182 F316/316L
BALL Floating Ball, Solid Ball ASTM A182 F316
SEAT Soft seat PEEK 2
SEAT HOLDER ASTM A182 F316L
SEAT SPRING N/A
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM / TRUNNION Shouldered anti-blow out ASTM A182 F316
STEM SEAL Elastomeric / Grafoil 2
ASTM F468 UNS N06625
BOLTING
ASTM F467 UNS N06625
Lever Operator
OPERATOR 4
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification
200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F11A Notes
Offering
MATERIAL GROUP Group 2.2
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE EG Flushing, Breathing Air
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged RTJ to ASME B16.5 3
BODY / BONNET Split body ASTM A351 CF8M
BALL Trunnion Mounted Ball, Solid Ball ASTM A182 F316
SEAT Soft seat PEEK 2
CAVITY VENT CONNECTION NO
SEAT HOLDER ASTM A182 F316L
SEAT SPRING INCONEL X750
BODY SEAL Primary Seal & Firesafe Secondary Seal AED type and suitable for service 2
STEM / TRUNNION Shouldered anti-blow out ASTM A182 F316
STEM SEAL Elastomeric / Grafoil 2
ASTM F468 UNS N06625
BOLTING
ASTM F467 UNS N06625
Lever Operator
OPERATOR 4
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification
200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
10. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F11A Notes
Offering
MATERIAL GROUP Group 2.2
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE EG Flushing, Breathing Air
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Flanged RTJ to ASME B16.5 3
BODY / BONNET Split body ASTM A351 CF8M
BALL Trunnion Mounted Ball, Solid Ball ASTM A182 F316
SEAT Soft seat PEEK 2
CAVITY VENT CONNECTION NO
SEAT HOLDER ASTM A182 F316L
SEAT SPRING INCONEL X750
BODY SEAL Primary Seal & Firesafe Secondary Seal AED type and suitable for service 2
STEM / TRUNNION Shouldered anti-blow out ASTM A182 F316
STEM SEAL Elastomeric / Grafoil 2
ASTM F468 UNS N06625
BOLTING
ASTM F467 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification
200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
11. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F25A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
FWS from WHP/RP to CP (Brownfield & Greenfield),1500# Closed Drain at RP
SERVICE
(Brownfield) (NACE)
TYPE Reduced Bore
DESIGN ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -29°C to +94°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F25A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
FWS from WHP/RP to CP (Brownfield & Greenfield),1500# Closed Drain at RP
SERVICE
(Brownfield) (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -29°C to +94°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
11. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F25A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
FWS from WHP/RP to CP (Brownfield & Greenfield),1500# Closed Drain at RP
SERVICE
(Brownfield) (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -29°C to +94°C
BALL Trunnion mounted Ball, Solid Ball ASTM B564 UNS N06625
SEAT Soft seat PEEK 2
CAVITY VENT CONNECTION NO
SEAT HOLDER ASTM B564 UNS N06625
SEAT SPRING INCONEL X750
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM / TRUNNION Shouldered anti-blow out UNS N07718
STEM SEAL Elastomeric / Grafoil 2
ASTM F468 UNS N06625
BOLTING Alloy Steel
ASTM F467 UNS N06625
OPERATOR Gear Operator 4, 10
MARKING MSS SP-25 7
TESTING Charpy test No
Leak test Yes
Torque test Yes (As per section 6.5.1 in 200-20-PI-SPC-00006)
INSPECTION & TESTS/
API 6D 1, 5
ACCEPTANCE
CERTIFICATIONS API 6D, EN 10204 Type 3.2
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 8
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves"
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
12. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F25A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
FWS from WHP/RP to CP (Brownfield & Greenfield),1500# Closed Drain at RP
SERVICE
(Brownfield) (NACE)
TYPE Full Bore
DESIGN ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -29°C to +94°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F25A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
FWS from WHP/RP to CP (Brownfield & Greenfield),1500# Closed Drain at RP
SERVICE
(Brownfield) (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -29°C to +94°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
11. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F25A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
FWS from WHP/RP to CP (Brownfield & Greenfield),1500# Closed Drain at RP
SERVICE
(Brownfield) (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -29°C to +94°C
BALL Trunnion mounted Ball, Solid Ball ASTM B564 UNS N06625
SEAT Soft seat PEEK 2
CAVITY VENT CONNECTION NO
SEAT HOLDER ASTM B564 UNS N06625
SEAT SPRING INCONEL X750
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM / TRUNNION Shouldered anti-blow out UNS N07718
STEM SEAL Elastomeric / Grafoil 2
ASTM F468 UNS N06625
BOLTING Alloy Steel
ASTM F467 UNS N06625
OPERATOR Gear Operator 4, 10
MARKING MSS SP-25 7
TESTING Charpy test No
Leak test Yes
Torque test Yes (As per section 6.5.1 in 200-20-PI-SPC-00006)
INSPECTION & TESTS/
API 6D 1, 5
ACCEPTANCE
CERTIFICATIONS API 6D, EN 10204 Type 3.2
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 8
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves"
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
12. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Blowdown High Pressure Piping (Short Segment BDV to Isolation Valve at CP Inlet
Header (For - 1500#),Blowdown High Pressure Piping (Short Segment BDV to
SERVICE Isolation Valve IN Compression System (For - 1500#),PSV High Pressure Low
Temperature Service (Only cover for 1500# PSV at compressor discharge
segment) (NACE)
TYPE Reduced Bore
DESIGN ASME B16.34, EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -100°C to +204°C
END CONNECTIONS Flanged RTJ to ASME B16.5 3
BODY / BONNET Split body ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Blowdown High Pressure Piping (Short Segment BDV to Isolation Valve at CP
Inlet Header (For - 1500#),Blowdown High Pressure Piping (Short Segment BDV
SERVICE to Isolation Valve IN Compression System (For - 1500#),PSV High Pressure Low
Temperature Service (Only cover for 1500# PSV at compressor discharge
segment) (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34, EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -100°C to +204°C
END CONNECTIONS Flanged RTJ to ASME B16.5 3
BODY / BONNET Split body ASTM A494 Gr. CW6MC
BALL Trunnion Mounted Ball, Solid Ball ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
11. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Blowdown High Pressure Piping (Short Segment BDV to Isolation Valve at CP
Inlet Header (For - 1500#),Blowdown High Pressure Piping (Short Segment BDV
SERVICE to Isolation Valve IN Compression System (For - 1500#),PSV High Pressure Low
Temperature Service (Only cover for 1500# PSV at compressor discharge
segment) (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34, EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -100°C to +204°C
END CONNECTIONS Flanged RTJ to ASME B16.5 3
BODY / BONNET Split body ASTM A494 Gr. CW6MC
BALL Trunnion Mounted Ball, Solid Ball ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
12. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 3
CORROSION ALLOWANCE 0 mm
Blowdown High Pressure Piping (Short Segment BDV to Isolation Valve at CP
Inlet Header (For - 1500#),Blowdown High Pressure Piping (Short Segment BDV
SERVICE to Isolation Valve IN Compression System (For - 1500#),PSV High Pressure Low
Temperature Service (Only cover for 1500# PSV at compressor discharge
segment) (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34, EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -100°C to +204°C
END CONNECTIONS Butt Weld Ends with Pup pieces to suit Pipe wall thickness 9,10
BODY / BONNET Top body ASTM A494 Gr. CW6MC 8
BALL Trunnion Mounted Ball, Solid Ball ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. Valve end wall thickness shall be as per ASME B16.25 to suit the following pipe wall thickness as mentioned in MTO description.
10. Valve shall be provided with body extensions (or) welded-on pipes of length as below, to allow field welding and PWHT, if specified,without
disassembly, distortion (or) damage to non-metallic internals.
1) For valves NPS 14 to NPS 16: 400 mm
2) For valves ≥ NPS 18: 800 mm
The material of the extension shall be forged (or) cast as a part of the body or shall be ASTM B705 UNS N06625 Gr.1 CL.2, Welded, pipe
material.The body extension wall thickness shall be as per thickness mentioned in the MTO description. Pressure testing shall be performed after
welding and heat treatment.
11. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
13. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Blowdown High Pressure Piping (Short Segment BDV to Isolation Valve at CP Inlet
Header (For - 1500#),Blowdown High Pressure Piping (Short Segment BDV to
SERVICE Isolation Valve IN Compression System (For - 1500#),PSV High Pressure Low
Temperature Service (Only cover for 1500# PSV at compressor discharge
segment) (NACE)
TYPE Full Bore
DESIGN ASME B16.34, EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -100°C to +204°C
END CONNECTIONS Flanged RTJ to ASME B16.5 3
BODY / BONNET Split body ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Blowdown High Pressure Piping (Short Segment BDV to Isolation Valve at CP
Inlet Header (For - 1500#),Blowdown High Pressure Piping (Short Segment BDV
SERVICE to Isolation Valve IN Compression System (For - 1500#),PSV High Pressure Low
Temperature Service (Only cover for 1500# PSV at compressor discharge
segment) (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34, EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -100°C to +204°C
END CONNECTIONS Flanged RTJ to ASME B16.5 3
BODY / BONNET Split body ASTM A494 Gr. CW6MC
BALL Trunnion Mounted Ball, Solid Ball ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
11. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Blowdown High Pressure Piping (Short Segment BDV to Isolation Valve at CP
Inlet Header (For - 1500#),Blowdown High Pressure Piping (Short Segment BDV
SERVICE to Isolation Valve IN Compression System (For - 1500#),PSV High Pressure Low
Temperature Service (Only cover for 1500# PSV at compressor discharge
segment) (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34, EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -100°C to +204°C
END CONNECTIONS Flanged RTJ to ASME B16.5 3
BODY / BONNET Split body ASTM A494 Gr. CW6MC
BALL Trunnion Mounted Ball, Solid Ball ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
12. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 3
CORROSION ALLOWANCE 0 mm
Blowdown High Pressure Piping (Short Segment BDV to Isolation Valve at CP
Inlet Header (For - 1500#),Blowdown High Pressure Piping (Short Segment BDV
SERVICE to Isolation Valve IN Compression System (For - 1500#),PSV High Pressure Low
Temperature Service (Only cover for 1500# PSV at compressor discharge
segment) (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34, EEMUA 192 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -100°C to +204°C
END CONNECTIONS Butt Weld Ends with Pup pieces to suit Pipe wall thickness 9,10
BODY / BONNET Top body ASTM A494 Gr. CW6MC
BALL Trunnion Mounted Ball, Solid Ball ASTM B564 UNS N06625
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. Valve end wall thickness shall be as per ASME B16.25 to suit the following pipe wall thickness as mentioned in MTO description.
10. Valve shall be provided with body extensions (or) welded-on pipes of length as below, to allow field welding and PWHT, if specified,without
disassembly, distortion (or) damage to non-metallic internals.
1) For valves NPS 14 to NPS 16: 400 mm
2) For valves ≥ NPS 18: 800 mm
The material of the extension shall be forged (or) cast as a part of the body or shall be ASTM B705 UNS N06625 Gr.1 CL.2, Welded, pipe
material.The body extension wall thickness shall be as per thickness mentioned in the MTO description. Pressure testing shall be performed after
welding and heat treatment.
11. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
13. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Closed Drain Pump ,Gas from RGE Comp.Discharge,Gas from RGE Comp.
Discharge Cooler to discharge SDV,Gas from RGE Comp.Discharge SDV to Riser
SERVICE Platform,Gas from QG2 Compressor Discharge,Gas from QG2 Comp.Discharge
Cooler to Riser Platform,Gas from CP1S (RL) Compressor Discharge, Diesel for
Valve Flushing, EG for Valve Flushing (NACE)
TYPE Reduced Bore
DESIGN ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -46°C to +94°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Closed Drain Pump ,Gas from RGE Comp.Discharge,Gas from RGE Comp.
Discharge Cooler to discharge SDV,Gas from RGE Comp.Discharge SDV to Riser
SERVICE Platform,Gas from QG2 Compressor Discharge,Gas from QG2 Comp.Discharge
Cooler to Riser Platform,Gas from CP1S (RL) Compressor Discharge, Diesel for
Valve Flushing, EG for Valve Flushing (NACE)
TYPE Reduced Bore
DESIGN ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -46°C to +204°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Seats and ball contact faces shall be Tungsten Carbide coated.The thickness of the Tungsten Carbide coating, after grinding and lapping, shall be
equal to 400 μm minimum. The minimum hardness shall be 1050 HV. Coating process shall be HVOF (High Velocity Oxygen Fuel)
11. The gap between the body and seat ring shall have an anti-debris lip or similar type design to minimize debris accumulation impairing the seat
dynamics and seal performance
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Closed Drain Pump ,Gas from RGE Comp.Discharge,Gas from RGE Comp.
Discharge Cooler to discharge SDV,Gas from RGE Comp.Discharge SDV to Riser
SERVICE Platform,Gas from QG2 Compressor Discharge,Gas from QG2 Comp.Discharge
Cooler to Riser Platform,Gas from CP1S (RL) Compressor Discharge, Diesel for
Valve Flushing, EG for Valve Flushing (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -46°C to +94°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
11. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Closed Drain Pump ,Gas from RGE Comp.Discharge,Gas from RGE Comp.
Discharge Cooler to discharge SDV,Gas from RGE Comp.Discharge SDV to Riser
SERVICE Platform,Gas from QG2 Compressor Discharge,Gas from QG2 Comp.Discharge
Cooler to Riser Platform,Gas from CP1S (RL) Compressor Discharge, Diesel for
Valve Flushing, EG for Valve Flushing (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -46°C to +204°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Seats and ball contact faces shall be Tungsten Carbide coated.The thickness of the Tungsten Carbide coating, after grinding and lapping, shall be
equal to 400 μm minimum. The minimum hardness shall be 1050 HV. Coating process shall be HVOF (High Velocity Oxygen Fuel)
11. The gap between the body and seat ring shall have an anti-debris lip or similar type design to minimize debris accumulation impairing the seat
dynamics and seal performance
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
13. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Closed Drain Pump ,Gas from RGE Comp.Discharge,Gas from RGE Comp.
Discharge Cooler to discharge SDV,Gas from RGE Comp.Discharge SDV to Riser
SERVICE Platform,Gas from QG2 Compressor Discharge,Gas from QG2 Comp.Discharge
Cooler to Riser Platform,Gas from CP1S (RL) Compressor Discharge, Diesel for
Valve Flushing, EG for Valve Flushing (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -46°C to +94°C
BALL Trunnion mounted Ball, Solid Ball ASTM B564 UNS N06625
SEAT Soft seat PEEK 2
CAVITY VENT CONNECTION NO
SEAT HOLDER ASTM B564 UNS N06625
SEAT SPRING INCONEL X750
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM / TRUNNION Shouldered anti-blow out UNS N07718
STEM SEAL Elastomeric / Grafoil 2
ASTM F468 UNS N06625
BOLTING Alloy Steel
ASTM F467 UNS N06625
OPERATOR Gear Operator 4, 10
MARKING MSS SP-25 7
TESTING Charpy test No
Leak test Yes
Torque test Yes (As per section 6.5.1 in 200-20-PI-SPC-00006)
INSPECTION & TESTS/
API 6D 1, 5
ACCEPTANCE
CERTIFICATIONS API 6D, EN 10204 Type 3.2
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 8
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves"
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
12. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Closed Drain Pump ,Gas from RGE Comp.Discharge,Gas from RGE Comp.
Discharge Cooler to discharge SDV,Gas from RGE Comp.Discharge SDV to Riser
SERVICE Platform,Gas from QG2 Compressor Discharge,Gas from QG2 Comp.Discharge
Cooler to Riser Platform,Gas from CP1S (RL) Compressor Discharge, Diesel for
Valve Flushing, EG for Valve Flushing (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -46°C to +204°C
BALL Trunnion mounted Ball, Solid Ball ASTM B564 UNS N06625 10
SEAT Metal seat ASTM B564 UNS N06625 10
CAVITY VENT CONNECTION NO
SEAT HOLDER ASTM B564 UNS N06625
SEAT SPRING INCONEL X750
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM / TRUNNION Shouldered anti-blow out UNS N07718
STEM SEAL Elastomeric / Grafoil 2
ASTM F468 UNS N06625
BOLTING Alloy Steel
ASTM F467 UNS N06625
OPERATOR Gear Operator 4, 11
MARKING MSS SP-25 7
TESTING Charpy test No
Leak test Yes
Torque test Yes (As per section 6.5.1 in 200-20-PI-SPC-00006)
INSPECTION & TESTS/
API 6D 1, 5
ACCEPTANCE
CERTIFICATIONS API 6D, EN 10204 Type 3.2
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 8
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves"
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Seats and ball contact faces shall be Tungsten Carbide coated.The thickness of the Tungsten Carbide coating, after grinding and lapping, shall be
equal to 400 μm minimum. The minimum hardness shall be 1050 HV. Coating process shall be HVOF (High Velocity Oxygen Fuel)
11. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
12. The gap between the body and seat ring shall have an anti-debris lip or similar type design to minimize debris accumulation impairing the seat
dynamics and seal performance
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
14. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Closed Drain Pump ,Gas from RGE Comp.Discharge,Gas from RGE Comp.
Discharge Cooler to discharge SDV,Gas from RGE Comp.Discharge SDV to Riser
SERVICE Platform,Gas from QG2 Compressor Discharge,Gas from QG2 Comp.Discharge
Cooler to Riser Platform,Gas from CP1S (RL) Compressor Discharge, Diesel for
Valve Flushing, EG for Valve Flushing (NACE)
TYPE Full Bore
DESIGN ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -46°C to +94°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Closed Drain Pump ,Gas from RGE Comp.Discharge,Gas from RGE Comp.
Discharge Cooler to discharge SDV,Gas from RGE Comp.Discharge SDV to Riser
SERVICE Platform,Gas from QG2 Compressor Discharge,Gas from QG2 Comp.Discharge
Cooler to Riser Platform,Gas from CP1S (RL) Compressor Discharge, Diesel for
Valve Flushing, EG for Valve Flushing (NACE)
TYPE Full Bore
DESIGN ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -46°C to +204°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Seats and ball contact faces shall be Tungsten Carbide coated.The thickness of the Tungsten Carbide coating, after grinding and lapping, shall be
equal to 400 μm minimum. The minimum hardness shall be 1050 HV. Coating process shall be HVOF (High Velocity Oxygen Fuel)
11. The gap between the body and seat ring shall have an anti-debris lip or similar type design to minimize debris accumulation impairing the seat
dynamics and seal performance
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Closed Drain Pump ,Gas from RGE Comp.Discharge,Gas from RGE Comp.
Discharge Cooler to discharge SDV,Gas from RGE Comp.Discharge SDV to Riser
SERVICE Platform,Gas from QG2 Compressor Discharge,Gas from QG2 Comp.Discharge
Cooler to Riser Platform,Gas from CP1S (RL) Compressor Discharge, Diesel for
Valve Flushing, EG for Valve Flushing (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -46°C to +94°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
11. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Closed Drain Pump ,Gas from RGE Comp.Discharge,Gas from RGE Comp.
Discharge Cooler to discharge SDV,Gas from RGE Comp.Discharge SDV to Riser
SERVICE Platform,Gas from QG2 Compressor Discharge,Gas from QG2 Comp.Discharge
Cooler to Riser Platform,Gas from CP1S (RL) Compressor Discharge, Diesel for
Valve Flushing, EG for Valve Flushing (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -46°C to +204°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Seats and ball contact faces shall be Tungsten Carbide coated.The thickness of the Tungsten Carbide coating, after grinding and lapping, shall be
equal to 400 μm minimum. The minimum hardness shall be 1050 HV. Coating process shall be HVOF (High Velocity Oxygen Fuel)
11. The gap between the body and seat ring shall have an anti-debris lip or similar type design to minimize debris accumulation impairing the seat
dynamics and seal performance
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
13. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Closed Drain Pump ,Gas from RGE Comp.Discharge,Gas from RGE Comp.
Discharge Cooler to discharge SDV,Gas from RGE Comp.Discharge SDV to Riser
SERVICE Platform,Gas from QG2 Compressor Discharge,Gas from QG2 Comp.Discharge
Cooler to Riser Platform,Gas from CP1S (RL) Compressor Discharge, Diesel for
Valve Flushing, EG for Valve Flushing (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -46°C to +94°C
BALL Trunnion mounted Ball, Solid Ball ASTM B564 UNS N06625
SEAT Soft seat PEEK 2
CAVITY VENT CONNECTION NO
SEAT HOLDER ASTM B564 UNS N06625
SEAT SPRING INCONEL X750
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM / TRUNNION Shouldered anti-blow out UNS N07718
STEM SEAL Elastomeric / Grafoil 2
ASTM F468 UNS N06625
BOLTING Alloy Steel
ASTM F467 UNS N06625
OPERATOR Gear Operator 4, 10
MARKING MSS SP-25 7
TESTING Charpy test No
Leak test Yes
Torque test Yes (As per section 6.5.1 in 200-20-PI-SPC-00006)
INSPECTION & TESTS/
API 6D 1, 5
ACCEPTANCE
CERTIFICATIONS API 6D, EN 10204 Type 3.2
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 8
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves"
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
12. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS F37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Closed Drain Pump ,Gas from RGE Comp.Discharge,Gas from RGE Comp.
Discharge Cooler to discharge SDV,Gas from RGE Comp.Discharge SDV to Riser
SERVICE Platform,Gas from QG2 Compressor Discharge,Gas from QG2 Comp.Discharge
Cooler to Riser Platform,Gas from CP1S (RL) Compressor Discharge, Diesel for
Valve Flushing, EG for Valve Flushing (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -46°C to +204°C
BALL Trunnion mounted Ball, Solid Ball ASTM B564 UNS N06625 10
SEAT Metal seat ASTM B564 UNS N06625 10
CAVITY VENT CONNECTION NO
SEAT HOLDER ASTM B564 UNS N06625
SEAT SPRING INCONEL X750
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM / TRUNNION Shouldered anti-blow out UNS N07718
STEM SEAL Elastomeric / Grafoil 2
ASTM F468 UNS N06625
BOLTING Alloy Steel
ASTM F467 UNS N06625
OPERATOR Gear Operator 4, 11
MARKING MSS SP-25 7
TESTING Charpy test No
Leak test Yes
Torque test Yes (As per section 6.5.1 in 200-20-PI-SPC-00006)
INSPECTION & TESTS/
API 6D 1, 5
ACCEPTANCE
CERTIFICATIONS API 6D, EN 10204 Type 3.2
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 8
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves"
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Seats and ball contact faces shall be Tungsten Carbide coated.The thickness of the Tungsten Carbide coating, after grinding and lapping, shall be
equal to 400 μm minimum. The minimum hardness shall be 1050 HV. Coating process shall be HVOF (High Velocity Oxygen Fuel)
11. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
12. The gap between the body and seat ring shall have an anti-debris lip or similar type design to minimize debris accumulation impairing the seat
dynamics and seal performance
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
14. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS G7E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
TYPE Reduced Bore
DESIGN API 608 / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 2500
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS G7E Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 2500
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
14. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS G7E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
TYPE Full Bore
DESIGN API 608 / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 2500
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS G7E Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 2500
DESIGN TEMP. -46°C to +85°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
14. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS G11A Notes
Offering
MATERIAL GROUP Group 2.2
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE MEG Injection, CI Injection, Diesel for Valve Flushing
TYPE Reduced Bore
DESIGN ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 2500
DESIGN TEMP. -29°C to +94°C
END CONNECTIONS Flanged RTJ to ASME B16.5 3
BODY / BONNET Split body ASTM A182 F316/316L
BALL Floating Ball, Solid Ball ASTM A182 F316
SEAT Soft seat PEEK 2
SEAT HOLDER ASTM A182 F316L
SEAT SPRING N/A
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM / TRUNNION Shouldered anti-blow out ASTM A182 F316
STEM SEAL Elastomeric / Grafoil 2
ASTM F468 UNS N06625
BOLTING
ASTM F467 UNS N06625
Lever Operator
OPERATOR 4
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification
200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS G11A Notes
Offering
MATERIAL GROUP Group 2.2
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE MEG Injection, CI Injection, Diesel for Valve Flushing
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 2500
DESIGN TEMP. -29°C to +94°C
END CONNECTIONS Flanged RTJ to ASME B16.5 3
BODY / BONNET Split body ASTM A351 CF8M
BALL Trunnion Mounted Ball, Solid Ball ASTM A182 F316
SEAT Soft seat PEEK 2
CAVITY VENT CONNECTION NO
SEAT HOLDER ASTM A182 F316L
SEAT SPRING INCONEL X750
BODY SEAL Primary Seal & Firesafe Secondary Seal AED type and suitable for service 2
STEM / TRUNNION Shouldered anti-blow out ASTM A182 F316
STEM SEAL Elastomeric / Grafoil 2
ASTM F468 UNS N06625
BOLTING
ASTM F467 UNS N06625
Gear Operator
OPERATOR 4, 9
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification
200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
11. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS G11A Notes
Offering
MATERIAL GROUP Group 2.2
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE MEG Injection, CI Injection, Diesel for Valve Flushing
TYPE Full Bore
DESIGN ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 2500
DESIGN TEMP. -29°C to +94°C
END CONNECTIONS Flanged RTJ to ASME B16.5 3
BODY / BONNET Split body ASTM A182 F316/316L
BALL Floating Ball, Solid Ball ASTM A182 F316
SEAT Soft seat PEEK 2
SEAT HOLDER ASTM A182 F316L
SEAT SPRING N/A
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM / TRUNNION Shouldered anti-blow out ASTM A182 F316
STEM SEAL Elastomeric / Grafoil 2
ASTM F468 UNS N06625
BOLTING
ASTM F467 UNS N06625
Lever Operator
OPERATOR 4
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification
200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS G11A Notes
Offering
MATERIAL GROUP Group 2.2
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
SERVICE MEG Injection, CI Injection, Diesel for Valve Flushing
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 2500
DESIGN TEMP. -29°C to +94°C
END CONNECTIONS Flanged RTJ to ASME B16.5 3
BODY / BONNET Split body ASTM A351 CF8M
BALL Trunnion Mounted Ball, Solid Ball ASTM A182 F316
SEAT Soft seat PEEK 2
CAVITY VENT CONNECTION NO
SEAT HOLDER ASTM A182 F316L
SEAT SPRING INCONEL X750
BODY SEAL Primary Seal & Firesafe Secondary Seal AED type and suitable for service 2
STEM / TRUNNION Shouldered anti-blow out ASTM A182 F316
STEM SEAL Elastomeric / Grafoil 2
ASTM F468 UNS N06625
BOLTING
ASTM F467 UNS N06625
Gear operator
OPERATOR 4, 9
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification
200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
11. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS G37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
SERVICE Liquid from Export Pump Discharge HIPPS Valve (NACE)
TYPE Reduced Bore
DESIGN ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 2500
DESIGN TEMP. -46°C to +94°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS G37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
SERVICE Liquid from Export Pump Discharge HIPPS Valve (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 2500
DESIGN TEMP. -46°C to +94°C
BALL Trunnion mounted Ball, Solid Ball ASTM B564 UNS N06625
SEAT Soft seat PEEK 2
CAVITY VENT CONNECTION NO
SEAT HOLDER ASTM B564 UNS N06625
SEAT SPRING INCONEL X750
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM / TRUNNION Shouldered anti-blow out UNS N07718
STEM SEAL Elastomeric / Grafoil 2
ASTM F468 UNS N06625
BOLTING Alloy Steel
ASTM F467 UNS N06625
OPERATOR Gear Operator 4, 10
MARKING MSS SP-25 7
TESTING Charpy test No
Leak test Yes
Torque test Yes (As per section 6.5.1 in 200-20-PI-SPC-00006)
INSPECTION & TESTS/
API 6D 1, 5
ACCEPTANCE
CERTIFICATIONS API 6D, EN 10204 Type 3.2
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 8
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves"
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
12. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS G37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
SERVICE Liquid from Export Pump Discharge HIPPS Valve (NACE)
TYPE Full Bore
DESIGN ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 2500
DESIGN TEMP. -46°C to +94°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Vendor
PIPING CLASS G37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
SERVICE Liquid from Export Pump Discharge HIPPS Valve (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 2500
DESIGN TEMP. -46°C to +94°C
BALL Trunnion mounted Ball, Solid Ball ASTM B564 UNS N06625
SEAT Soft seat PEEK 2
CAVITY VENT CONNECTION NO
SEAT HOLDER ASTM B564 UNS N06625
SEAT SPRING INCONEL X750
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM / TRUNNION Shouldered anti-blow out UNS N07718
STEM SEAL Elastomeric / Grafoil 2
ASTM F468 UNS N06625
BOLTING Alloy Steel
ASTM F467 UNS N06625
OPERATOR Gear Operator 4, 10
MARKING MSS SP-25 7
TESTING Charpy test No
Leak test Yes
Torque test Yes (As per section 6.5.1 in 200-20-PI-SPC-00006)
INSPECTION & TESTS/
API 6D 1, 5
ACCEPTANCE
CERTIFICATIONS API 6D, EN 10204 Type 3.2
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 8
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves"
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
10. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
11. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
12. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
NFPS Compression Project FEED
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 21 of 21
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
DOC No 200-20-PI-DTS-00001
Make : Sheet: 1 of 24
Range: NPS 6"
BALL VALVES Model : Revision: B
Vendor
PIPING CLASS A37A Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 0 mm
SERVICE Closed Drain Booster Pump, LP Flare (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -46°C to +175°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Make : Sheet: 2 of 24
Range: NPS 8"
BALL VALVES Model : Revision: B
Vendor
PIPING CLASS A37A Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 0 mm
SERVICE Closed Drain Booster Pump, LP Flare (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -46°C to +175°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Make : Sheet: 3 of 24
Range: NPS 10" to 16"
BALL VALVES Model : Revision: B
Vendor
PIPING CLASS A37A Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 0 mm
SERVICE Closed Drain Booster Pump, LP Flare (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -46°C to +175°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
14. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Make : Sheet: 4 of 24
Range: NPS 6"
BALL VALVES Model : Revision: B
Vendor
PIPING CLASS A37A Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 0 mm
SERVICE Closed Drain Booster Pump, LP Flare (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -46°C to +175°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
DOC No 200-20-PI-DTS-00001
Make : Sheet: 5 of 24
Range: NPS 8" to 16"
BALL VALVES Model : Revision: B
Vendor
PIPING CLASS A37A Notes
Offering
MATERIAL GROUP Group 1.2
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 0 mm
SERVICE Closed Drain Booster Pump, LP Flare (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -46°C to +175°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
14. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Make : Sheet: 6 of 24
Range: NPS 6" to 12"
BALL VALVES Model : Revision: B
Vendor
PIPING CLASS E37A Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 0 mm
FWS to Inlet Seperator, Gas from Inlet Seperator / Copm. Suction Scrubber, Gas
from CP1S(RL) Comp.Discharge Cooler to RT/RT2/PU Platform, Liquid from Inlet
SERVICE
Seperator up to booster Pump Discharge, Comp. Suction Scrubber Pump Discharge,
Diesel for Valve Flushing, EG for Valve Flushing (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 900
DESIGN TEMP. -46°C to +94°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
14. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Make : Sheet: 7 of 24
Range: NPS 14" to 48"
BALL VALVES Model : Revision: B
Vendor
PIPING CLASS E37A Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 3
CORROSION ALLOWANCE 0 mm
FWS to Inlet Seperator, Gas from Inlet Seperator / Copm. Suction Scrubber, Gas
from CP1S(RL) Comp.Discharge Cooler to RT/RT2/PU Platform, Liquid from Inlet
SERVICE
Seperator up to booster Pump Discharge, Comp. Suction Scrubber Pump Discharge,
Diesel for Valve Flushing, EG for Valve Flushing (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION ASME B16.10 (Long Pattern) (Upto 24") / Manufacturer Standard (Size 28" and
STANDARD above)
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 900
DESIGN TEMP. -46°C to +94°C
END CONNECTIONS Butt Weld Ends with Pup pieces to suit Pipe wall thickness 11, 12
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable for
Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10 Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. Valve end wall thickness shall be as per ASME B16.25 to suit the following pipe wall thickness as mentioned in MTO description.
12. Valve shall be provided with body extensions (or) welded-on pipes of length as below, to allow field welding and PWHT, if specified,without
disassembly, distortion (or) damage to non-metallic internals.
1) For valves NPS 14 to NPS 16: 400 mm
2) For valves ≥ NPS 18: 800 mm
The material of the extension shall be forged (or) cast as a part of the body or shall be ASTM B705 UNS N06625 Gr.1 CL.2, Welded, pipe
material.The body extension wall thickness shall be as per thickness mentioned in the MTO description. Pressure testing shall be performed after
welding and heat treatment.
13. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
14. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
15. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Make : Sheet: 8 of 24
Range: NPS 6" to 12"
BALL VALVES Model : Revision: B
Vendor
PIPING CLASS E37A Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 0 mm
FWS to Inlet Seperator, Gas from Inlet Seperator / Copm. Suction Scrubber, Gas
from CP1S(RL) Comp.Discharge Cooler to RT/RT2/PU Platform, Liquid from Inlet
SERVICE
Seperator up to booster Pump Discharge, Comp. Suction Scrubber Pump Discharge,
Diesel for Valve Flushing, EG for Valve Flushing (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 900
DESIGN TEMP. -46°C to +94°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
14. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Make : Sheet: 9 of 24
Range: NPS 14" to 48"
BALL VALVES Model : Revision: B
Vendor
PIPING CLASS E37A Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 3
CORROSION ALLOWANCE 0 mm
FWS to Inlet Seperator, Gas from Inlet Seperator / Copm. Suction Scrubber, Gas
from CP1S(RL) Comp.Discharge Cooler to RT/RT2/PU Platform, Liquid from Inlet
SERVICE
Seperator up to booster Pump Discharge, Comp. Suction Scrubber Pump Discharge,
Diesel for Valve Flushing, EG for Valve Flushing (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION ASME B16.10 (Long Pattern) (Upto 24") / Manufacturer Standard (Size 28" and
STANDARD above)
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 900
DESIGN TEMP. -46°C to +94°C
END CONNECTIONS Butt Weld Ends with Pup pieces to suit Pipe wall thickness 11, 12
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable for
Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-
CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10 Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. Valve end wall thickness shall be as per ASME B16.25 to suit the following pipe wall thickness as mentioned in MTO description.
12. Valve shall be provided with body extensions (or) welded-on pipes of length as below, to allow field welding and PWHT, if specified,without
disassembly, distortion (or) damage to non-metallic internals.
1) For valves NPS 14 to NPS 16: 400 mm
2) For valves ≥ NPS 18: 800 mm
The material of the extension shall be forged (or) cast as a part of the body or shall be ASTM B705 UNS N06625 Gr.1 CL.2, Welded, pipe
material.The body extension wall thickness shall be as per thickness mentioned in the MTO description. Pressure testing shall be performed after
welding and heat treatment.
13. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
14. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
15. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Make : Sheet: 10 of 24
Range: NPS 6" to 12"
BALL VALVES Model : Revision: B
Vendor
PIPING CLASS F25A Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 0 mm
FWS from WHP/RP to CP (Brownfield & Greenfield),1500# Closed Drain at RP
SERVICE
(Brownfield) (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -29°C to +94°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
14. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Make : Sheet: 11 of 24
Range: NPS 20"
BALL VALVES Model : Revision: B
Vendor
PIPING CLASS F25A Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 0 mm
FWS from WHP/RP to CP (Brownfield & Greenfield),1500# Closed Drain at RP
SERVICE
(Brownfield) (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -29°C to +94°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
14. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Make : Sheet: 12 of 24
Range: NPS 14" to 36"
BALL VALVES Model : Revision: B
Vendor
PIPING CLASS F25A Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 3
CORROSION ALLOWANCE 0 mm
FWS from WHP/RP to CP (Brownfield & Greenfield),1500# Closed Drain at RP
SERVICE
(Brownfield) (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION ASME B16.10 (Long Pattern) (Upto 20") / Manufacturer Standard (Size 24" and
STANDARD above)
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -29°C to +94°C
END CONNECTIONS Butt Weld Ends with Pup pieces to suit Pipe wall thickness 11, 12
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10 Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. Valve end wall thickness shall be as per ASME B16.25 to suit the following pipe wall thickness as mentioned in MTO description.
12. Valve shall be provided with body extensions (or) welded-on pipes of length as below, to allow field welding and PWHT, if specified,without
disassembly, distortion (or) damage to non-metallic internals.
1) For valves NPS 14 to NPS 16: 400 mm
2) For valves ≥ NPS 18: 800 mm
The material of the extension shall be forged (or) cast as a part of the body or shall be ASTM B705 UNS N06625 Gr.1 CL.2, Welded, pipe
material.The body extension wall thickness shall be as per thickness mentioned in the MTO description. Pressure testing shall be performed after
welding and heat treatment.
13. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
14. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
15. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Make : Sheet: 13 of 24
Range: NPS 6" to 12"
BALL VALVES Model : Revision: B
Vendor
PIPING CLASS F25A Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 0 mm
FWS from WHP/RP to CP (Brownfield & Greenfield),1500# Closed Drain at RP
SERVICE
(Brownfield) (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -29°C to +94°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
14. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Make : Sheet: 14 of 24
Range: NPS 14" to 36"
BALL VALVES Model : Revision: B
Vendor
PIPING CLASS F25A Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 3
CORROSION ALLOWANCE 0 mm
FWS from WHP/RP to CP (Brownfield & Greenfield),1500# Closed Drain at RP
SERVICE
(Brownfield) (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION ASME B16.10 (Long Pattern) (Upto 20") / Manufacturer Standard (Size 24" and
STANDARD above)
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -29°C to +94°C
END CONNECTIONS Butt Weld Ends with Pup pieces to suit Pipe wall thickness 11, 12
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10 Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. Valve end wall thickness shall be as per ASME B16.25 to suit the following pipe wall thickness as mentioned in MTO description.
12. Valve shall be provided with body extensions (or) welded-on pipes of length as below, to allow field welding and PWHT, if specified,without
disassembly, distortion (or) damage to non-metallic internals.
1) For valves NPS 14 to NPS 16: 400 mm
2) For valves ≥ NPS 18: 800 mm
The material of the extension shall be forged (or) cast as a part of the body or shall be ASTM B705 UNS N06625 Gr.1 CL.2, Welded, pipe
material.The body extension wall thickness shall be as per thickness mentioned in the MTO description. Pressure testing shall be performed after
welding and heat treatment.
13. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
14. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
15. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Make : Sheet: 15 of 24
Range: NPS 6" to 12"
BALL VALVES Model : Revision: B
Vendor
PIPING CLASS F37A Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 0 mm
Closed Drain Pump ,Gas from RGE Comp.Discharge,Gas from RGE Comp.
Discharge Cooler to discharge SDV,Gas from RGE Comp.Discharge SDV to Riser
SERVICE Platform,Gas from QG2 Compressor Discharge,Gas from QG2 Comp.Discharge
Cooler to Riser Platform,Gas from CP1S (RL) Compressor Discharge, Diesel for
Valve Flushing, EG for Valve Flushing (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -46°C to +94°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
14. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Make : Sheet: 16 of 24
Range: NPS 6" to 12"
BALL VALVES Model : Revision: B
Vendor
PIPING CLASS F37A Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 0 mm
Closed Drain Pump ,Gas from RGE Comp.Discharge,Gas from RGE Comp.
Discharge Cooler to discharge SDV,Gas from RGE Comp.Discharge SDV to Riser
SERVICE Platform,Gas from QG2 Compressor Discharge,Gas from QG2 Comp.Discharge
Cooler to Riser Platform,Gas from CP1S (RL) Compressor Discharge, Diesel for
Valve Flushing, EG for Valve Flushing (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -46°C to +204°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12 Seats and ball contact faces shall be Tungsten Carbide coated.The thickness of the Tungsten Carbide coating, after grinding and lapping, shall be
equal to 400 μm minimum. The minimum hardness shall be 1050 HV. Coating process shall be HVOF (High Velocity Oxygen Fuel)
13. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
14. The gap between the body and seat ring shall have an anti-debris lip or similar type design to minimize debris accumulation impairing the seat
dynamics and seal performance
15. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
16. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Make : Sheet: 17 of 24
Range: NPS 14" to 36"
BALL VALVES Model : Revision: B
Vendor
PIPING CLASS F37A Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 3
CORROSION ALLOWANCE 0 mm
Closed Drain Pump ,Gas from RGE Comp.Discharge,Gas from RGE Comp.
Discharge Cooler to discharge SDV,Gas from RGE Comp.Discharge SDV to Riser
SERVICE Platform,Gas from QG2 Compressor Discharge,Gas from QG2 Comp.Discharge
Cooler to Riser Platform,Gas from CP1S (RL) Compressor Discharge, Diesel for Valve
Flushing, EG for Valve Flushing (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern) (Upto 20") / Manufacturer Standard (Size 24" and above)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -46°C to +94°C
END CONNECTIONS Butt Weld Ends with Pup pieces to suit Pipe wall thickness 11, 12
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10 Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. Valve end wall thickness shall be as per ASME B16.25 to suit the following pipe wall thickness as mentioned in MTO description.
12. Valve shall be provided with body extensions (or) welded-on pipes of length as below, to allow field welding and PWHT, if specified,without
disassembly, distortion (or) damage to non-metallic internals.
1) For valves NPS 14 to NPS 16: 400 mm
2) For valves ≥ NPS 18: 800 mm
The material of the extension shall be forged (or) cast as a part of the body or shall be ASTM B705 UNS N06625 Gr.1 CL.2, Welded, pipe
material.The body extension wall thickness shall be as per thickness mentioned in the MTO description. Pressure testing shall be performed after
welding and heat treatment.
13. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
14. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
15. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Make : Sheet: 18 of 24
Range: NPS 6" to 12"
BALL VALVES Model : Revision: B
Vendor
PIPING CLASS F37A Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 0 mm
Closed Drain Pump ,Gas from RGE Comp.Discharge,Gas from RGE Comp.
Discharge Cooler to discharge SDV,Gas from RGE Comp.Discharge SDV to Riser
SERVICE Platform,Gas from QG2 Compressor Discharge,Gas from QG2 Comp.Discharge
Cooler to Riser Platform,Gas from CP1S (RL) Compressor Discharge, Diesel for
Valve Flushing, EG for Valve Flushing (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -46°C to +94°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be
suitable for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
14. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Make : Sheet: 19 of 24
Range: NPS 6" to 12"
BALL VALVES Model : Revision: B
Vendor
PIPING CLASS F37A Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 0 mm
Closed Drain Pump ,Gas from RGE Comp.Discharge,Gas from RGE Comp.
Discharge Cooler to discharge SDV,Gas from RGE Comp.Discharge SDV to Riser
SERVICE Platform,Gas from QG2 Compressor Discharge,Gas from QG2 Comp.Discharge
Cooler to Riser Platform,Gas from CP1S (RL) Compressor Discharge, Diesel for
Valve Flushing, EG for Valve Flushing (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -46°C to +204°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. Seats and ball contact faces shall be Tungsten Carbide coated.The thickness of the Tungsten Carbide coating, after grinding and lapping, shall be
equal to 400 μm minimum. The minimum hardness shall be 1050 HV. Coating process shall be HVOF (High Velocity Oxygen Fuel)
13. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
14. The gap between the body and seat ring shall have an anti-debris lip or similar type design to minimize debris accumulation impairing the seat
dynamics and seal performance
15. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
16. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Make : Sheet: 20 of 24
Range: NPS 14" to 36"
BALL VALVES Model : Revision: B
Vendor
PIPING CLASS F37A Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 3
CORROSION ALLOWANCE 0 mm
Closed Drain Pump ,Gas from RGE Comp.Discharge,Gas from RGE Comp.
Discharge Cooler to discharge SDV,Gas from RGE Comp.Discharge SDV to Riser
SERVICE Platform,Gas from QG2 Compressor Discharge,Gas from QG2 Comp.Discharge
Cooler to Riser Platform,Gas from CP1S (RL) Compressor Discharge, Diesel for Valve
Flushing, EG for Valve Flushing (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern) (Upto 20") / Manufacturer Standard (Size 24" and above)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -46°C to +94°C
END CONNECTIONS Butt Weld Ends with Pup pieces to suit Pipe wall thickness 11, 12
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10 Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. Valve end wall thickness shall be as per ASME B16.25 to suit the following pipe wall thickness as mentioned in MTO description.
12. Valve shall be provided with body extensions (or) welded-on pipes of length as below, to allow field welding and PWHT, if specified,without
disassembly, distortion (or) damage to non-metallic internals.
1) For valves NPS 14 to NPS 16: 400 mm
2) For valves ≥ NPS 18: 800 mm
The material of the extension shall be forged (or) cast as a part of the body or shall be ASTM B705 UNS N06625 Gr.1 CL.2, Welded, pipe
material.The body extension wall thickness shall be as per thickness mentioned in the MTO description. Pressure testing shall be performed after
welding and heat treatment.
13. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
14. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
15. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Make : Sheet: 21 of 24
Range: NPS 6" to 12"
BALL VALVES Model : Revision: B
Vendor
PIPING CLASS G37A Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 0 mm
SERVICE Liquid from Export Pump Discharge HIPPS Valve (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 2500
DESIGN TEMP. -46°C to +94°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
14. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Make : Sheet: 22 of 24
Range: NPS 14"
BALL VALVES Model : Revision: B
Vendor
PIPING CLASS G37A Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 3
CORROSION ALLOWANCE 0 mm
SERVICE Liquid from Export Pump Discharge HIPPS Valve (NACE)
TYPE Reduced Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
Manufacturer Standard
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 2500
DESIGN TEMP. -46°C to +94°C
END CONNECTIONS Butt Weld Ends with Pup pieces to suit Pipe wall thickness 11, 12
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10 Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. Valve end wall thickness shall be as per ASME B16.25 to suit the following pipe wall thickness as mentioned in MTO description.
12. Valve shall be provided with 400MM body extensions (or) welded-on pipes to allow field welding and PWHT, if specified,without disassembly,
distortion (or) damage to non-metallic internals. The material of the extension shall be forged (or) cast as a part of the body or shall be API SPEC
5L X60 PSL2, with 3mm UNS N06625 Internal weld overlay, Seamless (Upto 16") or API SPEC 5L X60 PSL2, with 3mm UNS N06625 Internal Weld
(18" & Above ) overlay,Welded with 100% RT .The body extension wall thickness shall be as per thickness mentioned in the MTO description.
Pressure testing shall be performed after welding and heat treatment.
13. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
14. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
15. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Make : Sheet: 23 of 24
Range: NPS 6" to 12"
BALL VALVES Model : Revision: B
Vendor
PIPING CLASS G37A Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 11
CORROSION ALLOWANCE 0 mm
SERVICE Liquid from Export Pump Discharge HIPPS Valve (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
ASME B16.10 (Long Pattern)
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 2500
DESIGN TEMP. -46°C to +94°C
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts, Nuts and Gaskets
11. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
12. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
13. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
14. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.
DOC No 200-20-PI-DTS-00001
Make : Sheet: 24 of 24
Range: NPS 14"
BALL VALVES Model : Revision: B
Vendor
PIPING CLASS G37A Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 3
CORROSION ALLOWANCE 0 mm
SERVICE Liquid from Export Pump Discharge HIPPS Valve (NACE)
TYPE Full Bore
DESIGN API 6D / ASME B16.34 6
END TO END DIMENSION
Manufacturer Standard
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 2500
DESIGN TEMP. -46°C to +94°C
END CONNECTIONS Butt Weld Ends with Pup pieces to suit Pipe wall thickness 11, 12
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts
or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 -
Material Requirements for Sour Service
4. Valves to have locking facility to allow locking in the open and closed position & all exposed items like thrust bearing,stop pins etc shall be suitable
for Marine Offshore environment.
5. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
6. Valves shall have bi-directional shut off.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material
shall be used for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during
assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-
20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10 Bolting, including nuts and washers, shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
11. Valve end wall thickness shall be as per ASME B16.25 to suit the following pipe wall thickness as mentioned in MTO description.
12. Valve shall be provided with 400MM body extensions (or) welded-on pipes to allow field welding and PWHT, if specified,without disassembly,
distortion (or) damage to non-metallic internals. The material of the extension shall be forged (or) cast as a part of the body or shall be API SPEC
5L X60 PSL2, with 3mm UNS N06625 Internal weld overlay, Seamless (Upto 16") or API SPEC 5L X60 PSL2, with 3mm UNS N06625 Internal Weld
(18" & Above ) overlay,Welded with 100% RT .The body extension wall thickness shall be as per thickness mentioned in the MTO description.
Pressure testing shall be performed after welding and heat treatment.
13. The Gearbox drive shall be suitable for any stem orientation of operation in horizontal or vertical up position.
14. Valves shall be suitable for any installation positions (Horizontal, Vertical & Inclined positions) with different stem orientations.
15. The Bleed/Drain ports (if applicable) shall be supplied with blind flanged connection.