Professional Documents
Culture Documents
Timer Omron 24 H
Timer Omron 24 H
Features (B)
Fiber
optic
● Easy to check and change the program setting sensor
(G)
Connector/
Ordering information Socket
LE7 M 2 (H)
Temp.
controller
(I)
SSR/
Output Power
2 2 Relay outputs controller
Size
M DIN W72×H7mm (J)
Counter
Item
LE7 Weekly/Yearly timer
(K)
Timer
Specifications (L)
Panel
meter
Model LE7M-2
(M)
Power supply 100-240VAC 50/60Hz Tacho/
Speed/ Pulse
meter
Allowable voltage range 90 to 110% of rated voltage
Power consumption Max. 4.2VA (N)
Display
unit
RETURN input Short-circuit or open by switch or relay
Timing program 48 steps for weekly, 24 steps for yearly (O)
Sensor
Operation mode ON/OFF mode, cycle mode, pulse mode controller
Noise strength ±2kV the square wave noise(pulse width: 1㎲) by the noise simulator
(U)
Environ Ambient temperature -10 to 55℃, storage: -25 to 65℃ Other
K-75
LE7M-2
Connections OUT2
N.C. N.O. RETURN
COM INPUT
6 7 8 9 10
1 2 3 4 5
COM
N.O. N.C.
OUT1 SOURCE
CONTACT OUT 100-240VAC
250VAC 10A 50/60㎐ 4.2VA
RESISTIVE LOAD
Load connection
You must connect a surge absorber to the both ends of the load to prevent from damage or malfunction of this unit when
controlling non-resistive load (ex: magnetic switch, etc).
N.O. N.C.
COM
1 2 3 4 5
Power of Power of
single N.O. N.C. three N.O. N.C.
phase phase
COM COM
1 2 3 4 5 1 2 3 4 5
SOURCE SOURCE
S/A S/A
Magnetic Magnetic
Switch Switch
Load
Load S/A : Surge Absorber S/A : Surge Absorber
K-76
Weekly/Yearly Timer
Dimensions & Mounting (unit: mm) (A)
Photo
electric
1) Front panel mounting sensor
(C)
68 +0.7
Door/Area
0
sensor
Min. 91
67.5
68 +0.7
0 (D)
Proximity
sensor
(E)
Pressure
2) Surface mounting sensor
(G)
Connector/
Socket
95
85
85
(H)
Temp.
controller
(I)
SSR/
Power
55 controller
(K)
Timer
DIN rail
(L)
Panel
95
95
meter
(M)
Tacho/
Speed/ Pulse
meter
Base plate
(N)
Display
Remove terminals from the body after unscrewing terminal screws, and then assemble terminals to the body after rotating (O)
Sensor
terminals as shown below. controller
(P)
① Unscrew 4 bolts from terminal block. ② Detach terminal block from case and then rotate it 180 degree. Switching
mode power
supply
(Q)
Stepper
motor&
Driver&Controller
(R)
Graphic/
Logic
panel
(S)
Field
network
device
(Front panel mounting)
③ Assemble terminal block to case by using the 4 bolts. (T)
Software
(U)
Other
(Surface mounting)
K-77
LE7M-2
Parts description
1 10
11
2
12
3 13
4 14
5 15
6 16
7 17
8 18
9 19
20
23
21
24
22
Functions
Program setting and output operation ● Weekly ON/OFF mode
Output1/Output2 operates according to Program1 and Output operation by ON/OFF set time.
Program2. • Min. time setting unit : 1 min.
• It is able to set ON/OFF day separately.
• One record in two Steps(ON day/ON time, OFF day/OFF
Definitions time)
● Record : A part of program that controls output operation.
● Step : Basic component of record.
K-78
Weekly/Yearly Timer
• Set range for ON/OFF time width Display and change of next mode (A)
Photo
: 1min. to 12 hour 59min. ● The day of next mode in Program1 or Program2 is electric
• One record in 3 steps(ON day/ON time, OFF day/OFF displayed on the day indicator, and the time of next mode
sensor
time, ON time width/OFF time width) is displayed on the lower row of screen. Press +
(B)
Fiber
optic
OFF width in RUN mode it is changed from program1 to sensor
Output turns ON at ON time for a specified pulse width. In setting group 2-Level 2(Power restore), select auto [AT] (E)
(Pulse width : 1 to 59sec., 1 to 60min.) or normal [NOR] by or key, and press key to set. Pressure
sensor
• One record in two steps(ON day/ON time, pulse width) ● Auto [AT] power restore mode
Output(OUT1, OUT2) operates according to program when (F)
Rotary
power turns on again after power failure. encoder
Pulse width ● Normal [NOR] power restore mode
(1 to 59sec., 1 to 60min.)
When power turns on again after power failure, output is (G)
Connector/
kept OFF and RET.IN flashes on the panel. When power Socket
at OFF time on STOP date. Please use reliable contacts enough to flow 0.1mA of (J)
• One record in three steps(START/STOP date, ON/OFF current at 5VDC when use switch or relay. Counter
time)
● Yearly pulse mode Season switching mode
(K)
Output turns ON at ON time on START date and turns This feature uses for setting seasonal weekly operation Timer
OFF at OFF time on STOP time for a specified pulse width mode.
repeatedly.(Pulse width : 1 to 59sec., 1 to 60min.). To operate this mode, save starting month and date, (L)
Panel
• One record in three steps(START/STOP date, ON time, ending month and date of each season which displays S1, meter
pulse width) S2, S3, S4 then set day and time of each season in weekly
program setting. It is also able to operate only in summer (M)
Tacho/
and winter season. (S1: set summer season, S2: set winter Speed/ Pulse
Program operation
meter
season, S3/S4: do not set)
At the season switching selection LEVEL 2 status in setting (N)
Display
2 group (SEN turns ON, OFF flashes), select ON [ON] by unit
Weekly setting 1 of Program1 pressing or key and press key to complete the
(O)
Weekly setting 2 of Program1 season switching. Sensor
controller
Be sure that if changing season switching from OFF to ON
Yearly setting 1 of Program1 or, ON to OFF, the weekly program 1(P1) and the weekly (P)
Switching
Program1 mode program 2 (P2) which are set before are deleted. mode power
supply
● ON [ON] mode
① ② ③ ④ ⑤ ⑥ Weekly program is switched automatically by season (Q)
Stepper
switching. motor&
Driver&Controller
● ⑤ to ⑥ : O
perated by yearly setting 1 of Program 1. START and STOP turn ON), press key. (S)
(During weekly program operation at 12:00 AM on ② Advance to the flashing position of season selection Field
network
START date, the weekly program operation stops, and it among S1, S2, S3, S4 by or key and press device
K-79
LE7M-2
Daylight saving time Current time setting
To utilize daylight during the summer season, daylight (Ex) Set the current time as 10, Mar, 2008, 5:10 PM.
saving time is adjusted forward one hour from standard
time. ① Advance to the current time setting mode
In setting group 2-LEVEL 2(DST turns ON, AT or NOR SUN MON TUE WED THU FRI SAT
K-80
Weekly/Yearly Timer
Program setting (A)
Photo
electric
Setting group 1 Setting group 2 sensor
(B)
RUN mode RUN mode Fiber
optic
Press MODE key Press MODE key Press MODE key Press MODE + SET key sensor
for 3sec. for 3sec. (Setting group 1) for 3sec. for 3sec. (Setting group 2)
MODE (C)
LEVEL1 Door/Area
LEVEL1
LEVEL2 LEVEL2 sensor
MODE MODE
LEVEL1 LEVEL2 LEVEL1 LEVEL2 (E)
Pressure
Program2 weekly SET
Program2 weekly Power failure return selection mode SET
Power failure sensor
MODE
season turns ON and
LEVEL1 LEVEL2 START or STOP turns ON) (J)
Counter
MODE
is Normal [NOR]. Stepper
motor&
LEVEL1 LEVEL2 ● When it advances to setting group 2 in RUN mode, Driver&Controller
(U)
● When it advances to setting group 1 in RUN mode, Other
output (OUT1, OUT2) will be OFF.
● It returns to previous setting group 1 when power of time
switch is ON again in setting group 1.
● When MODE key is pressed in LEVEL2 of setting group 1,
current setting will be canceled and it returns to previous
LEVEL1.
K-81
LE7M-2
Weekly program setting ⑦ OFF time setting(AM, PM)
● Weekly ON/OFF mode SUN MON TUE WED THU FRI SAT
(Ex) Output1(OUT1) is ON from Monday to Friday at 8:00 Select PM by or key
AM and OFF at 6:10 PM. and move the flashing to
hour position by key.
SUN MON TUE WED THU FRI SAT
8:00 6:10 8:00 6:10 8:00 6:10 8:00 6:10 8:00 6:10
AM PM AM PM AM PM AM PM AM PM
⑧ OFF time setting(Hour, Min.)
① Advance to program1(P1) weekly program SUN MON TUE WED THU FRI SAT
setting mode
Move the flashing to minute
SUN MON TUE WED THU FRI SAT
MODE key is pressed over position after set 6:00 by
3sec. in RUN mode, PROG or key and set the minute
P1 flashes and press SET as 10 and press SET key.
key.
⑨ Complete to set
SUN MON TUE WED THU FRI SAT
② Mode type setting
SUN MON TUE WED THU FRI SAT
Press SET key to set
Press SET key in ON/OFF additional program.
mode.
K-82
Weekly/Yearly Timer
④ ON day setting ● Weekly cycle mode (A)
SUN MON TUE WED THU FRI SAT (Ex) Output1(OUT1) is ON for 10min and OFF for 5min from Photo
electric
Press key to move the monday 6:00AM to saturday 5:30PM. SAT sensor
(R)
Graphic/
Logic
panel
⑪ Complete to set
(S)
SUN MON TUE WED THU FRI SAT Field
Press SET key to set network
device
additional program.
(T)
Software
(U)
Other
K-83
LE7M-2
Weekly day change Yearly holiday mode
It operates when the specified day mode is required It operates to off the output without program adjustment
to install in other day from the set day and it returns to during previously set yearly holiday period available from
previous program setting automatically when it is finished. present year to 31, Dec. of the next year.
It is applied to program1(P1) and program2(P2). Designate the start date of yearly holiday and year of end
● Weekly day change cancellation date as every year [--] to repeat the holiday mode for
① Change current year, month, date in current time setting specified in every year.
mode
② Change standard day ● Setting example
③ Delete all program in program1(P1) and program2 (P2) Set every year 5, May to off the output(OUT1, OUT2).
④ Season switching
● Setting example ① Advance to yearly holiday mode
Output1(OUT1) is ON in Saturday at 9:00AM and OFF at SUN MON TUE WED THU FRI SAT
12:00PM and it is ON 8:30AM and OFF at 6:00PM from Press MODE key over 3sec.
Monday to Friday and the mode of Monday and Tuesday is to move to the setting
operated temporarily as Saturday(standard) program. group1 in RUN mode and
press it repeatedly until hDY
① Advance to weekly day change mode flashes in second display
SUN MON TUE WED THU FRI SAT part and press SET key.
Press MODE key over 3sec.
to move to the setting
② Yearly holiday No. display
group1 in RUN mode and
SUN MON TUE WED THU FRI SAT
press it repeatedly until cDY Press SET key after check
is flashed in second display yearly holiday No.
part and press SET key.
K-84
Weekly/Yearly Timer
Yearly program setting ⑧ OFF time setting(Hour, Minute) (A)
Photo
● Yearly ON/OFF mode SUN MON TUE WED THU FRI SAT electric
sensor
(Ex) Output1(OUT1) is ON from every 5, Apr to 7, Apr at Move the flashing to minute
9:00AM and OFF 5:10PM. position after set 5:00 by (B)
Fiber
① Advance to program1(P1) yearly program or key and set the minute optic
sensor
K-85
LE7M-2
⑤ ON time setting(AM, PM) Yearly program check, modify and delete
SUN MON TUE WED THU FRI SAT
key is pressed, move the RUN mode
flashing to hour position and Press MODE key Press CHECK
for 3sec. key for 1sec.
select PM by or key
when ON time is afternoon.
Press SET
Program1 Yearly program key for 3sec. Program1 Yearly program
record No.1 [r01] record No.1 [r01] setting
⑥ ON time setting(Hour, Minute) setting check modify and delete
SUN MON TUE WED THU FRI SAT CHECK
Press or key twice to
Press SET
set 10 and press SET key Program1 Yearly program key for 3sec. Program1 Yearly program
after check 00min. record No.2 [r02] record No.2 [r02] setting
setting check modify and delete
CHECK
⑦ Pulse width setting Press SET
SUN MON TUE WED THU FRI SAT Program2 Yearly program key for 3sec. Program2 Yearly program
Press or key 4 times record No.1 [r01] record No.1 [r01] setting
to select pulse width as 5s setting check modify and delete
and press SET key.
CHECK
Press SET
Program1 weekly program key for 3sec. Program1 weekly program
record No.2 [r02] record No.2 [r02] setting
setting check modify and delete
CHECK
Press SET
Program2 weekly program key for 3sec. Program2 weekly program
record No.1 [r01] record No.1 [r01] setting
setting check modify and delete
CHECK
K-86