DAVR – CPU module 69203DB1A(UN0660) Processor – 16 bit, TMS9995 (Texas Instruments) at 12Mhz. Memory – 32 Kbytes Program memory (EPROM) 4 x 8 Kbytes - EPROM/EEPROM/RAM Serial Interface - RS232/RS422 (Programmable) Digital Inputs – 6 (TTL level), 10 (HCMOS), 7 (24 Volts) Digital Outputs – 9 (TTL Level), 14 (HCMOS), 4 (24 Volts) I/O BUS – 1 to 16 bits Serial, addressable up to 4096 bits. Together with Analog I/O module 69203IV1A (UN0611) Analog Inputs - 8 Channels (Bipolar, Programmable as ±10V or ±50V) Analog Outputs – 1 Channel, ±10V. Digital Inputs – 4 (24 Volts) Digital Outputs – 1 (24 Volt) Relay contact Outputs – 4 NC / NO Power supply: +5V, ±15V, +24V DAVR – Interrupt Generator module 69203GB1A(UN0661) Measures Generator voltage (7Vdc at 3 x 22Vac(line) input) Measures Generator current (7Vdc at 3 x 5Vac input) (4.2Vdc at 3 x 3Vac input) Measures Sync voltage (7Vdc at 3 x 22Vac(line) input) Conditions Field Current (3Vdc nominal) Generates 12 interrupts per Cycle (sync to R-phase signal) Generates 12 interrupts per 20ms (during free run condition) Monitors frequency and voltage level of actual output. Program execution in CPU is monitored. Interrupt rate is monitored. Internal clock is monitored. Digital Inputs – 5 (24 Volt), 6 (HCMOS) Digital Outputs – 16 (HCMOS), 2 (24 Volts) Power supply: +5V, ±15V, +24V DAVR – Digital I/O module 69203NB1A(UN0662) Digital Inputs – 16 (24V) Static inputs. Digital Inputs – 16 (24V) Programmable as Pulse/Static inputs. Digital Outputs: 32 (24V) Self monitoring of the module. Module selection through 2 x 6-bit address Switch. (One switch for I/P address and Other for O/P) Power supply: +5V, +24V DAVR – Digital Firing and control module 69203DU1xA(UN0663-xxx) Processor – 16 bit, TMS9995 (Texas Instruments) at 12Mhz. Memory – 32 Kbytes Program memory (EPROM) Digital Inputs – 16 (24 Volts) Digital Outputs – 8 (24 Volts) Analog inputs – 3 (Bipolar ±10V) Analog Outputs – 1(Bipolar ±10V) Measures synchronizing input. Generates 6 firing pulses(angle 10°min to 170°max according to Control input with frequency compensation (10 Hz to 180Hz for rated freq of 50, 75, and 150Hz and 10 to 1.1x rated freq for rated freq >=300Hz). Control input as analog or Digital(selected thro 6 bit add. Switch) Controlling action selectable as Uc/If and Internal/external. Pulse blocking if any of the pulse is shorted to GND/other pulse. Reference value generator selectable as internal and external. Follow-up control with the additional reference value input. Power supply: +5V, ±15V, +24V DAVR- Analog I/O module 69203NA1A(UN0610) Analog inputs - 16 (common mode) or 8 (diff. mode) 0 to +10V or ±10V (selectable) 6 channels used as sample and Hold inputs. Analog Outputs – 2 (0 to 10V or ±10V ; selectable) Module selection through 2 x 6 bit address switch. (One switch for I/P address and Other for O/P) Self checking for functioning of A/D and D/A chips. Power supply: +5V, ±15V, +24V DAVR – Alarm Indication module 69203SV1A(UN0665)
No of Channels – 32 (LED indication)
Module selection through 6 bit address switch. Module can be used as Master or Slave. Power supply: +5V DAVR – Current Flow Monitor module 69203SJ1A(UN0667) Used in Excitation Monitoring system only. Checks for the conduction of the Thyristor within 1 ms time after giving the firing Pulse. Monitors up to 2 Thyristor Bridges. Failure of each Thyrisotr is indicated by lighting a corresponding LED on the Front Panel of the module. Master and Slave operation. Self testing of the firing pulse inputs and internal timing circuit. On failure of any firing pulse or timing circuit, entire monitoring is blocked. Module selection is through 4 bit address switch Power supply: +5V, ±15V, +24V DAVR – Micro terminal module 69203TB2A(UNS2660) Used for data communication with CPU module Displays 4 lines of Hex or Decimal Data on LCD (4 x 16 char) Identifies automatically the target CPU. Data read memory range: 0000H to FFFFH Data write memory range: Depends on the target CPU module. 4 analog signals corresponding to the 4 Hex data displayed are available at 4 test points. Gets 24Vdc supply from the target CPU. RS232 printer Output port. 5 x 6 matrix keypads with de-bounce arrest circuit. 12 keys with dual function with the help of Shift key. Power supply: 24Vdc Failure of communication with CPU module is indicated by ‘Transfer Error’ with periodic checking for communication. DAVR – DC-DC Power supply module 69203PY1A(UN0664) Input : 110Vdc(82V - 156V), 1.7A(2.3A - 1.2A) 220Vdc(165V-312V), 0.85A (1.13A – 0.6A) Output: +5V(5.0V to 5.2V) ,5A, 0.3A Base load. ±15V(± 14.21V to ± 15.8V), ± 1.0A, ±0.1A Base load +24V(22.8V to 26.4V), 4.0A, 0.2A Base load Over voltage monitoring : 5.5 V on 5V output (instant tripping) Under Voltage monitoring : 4.7V, ±13.9V, 21V (Trips after 10 s) Remote shutdown facility. Parallel connection of 2 modules with current balancing. DAVR – AC-DC Supply module 69203PZ1A(UNC4664) Input: 82Vac- 165Vac(±10%), 12.3A max 110Vdc to 250Vdc (±25%),,15A max Output: 82Vdc to 312Vdc , 13A max DAVR – Voltage and current measuring module 69203IA1A(UNC4660) Input Voltage: Generator, synchronizing & a spare Rated Input: 3x100Vac .. 120Vac(Generator and synchronizing) 1x100Vac .. 120Vac(spare) Rated Frequency: 50/60Hz, Input voltage range: 0 to 130% of rated Input Frequency range: 80 to 120% of rated Input Current: Generator Current, Field Current Rated Input: 3 x 1A or 5A(Generator); 2 x 1A or 5A(Field) Rated Frequency: 50/60Hz, Input Current range: 0 to 150% of rated Input Frequency range: 80 to 120% of rated Output Voltage: 3 x 20..24Vac (Generator and Synchronizing) 1 x 20.. 24Vac(Spare) Phase Error input/output <1°el Output Current: 3 x 3Vac (Generator) 1 x 3Vdc (Field) DAVR-Binary Input module 69203IBxA(UNC4661) No of Channels: 16 Input voltage: 24V, 48V, 110V, 125V, 220V, 250V selectable thro’ input resistance value No of outputs: 16 Output Voltage: 20Vdc to 23Vdc at 10ma load. Isolation: Input to Input : 2KVac for 1 Min Input to Output: 2.5KVac for 1 Min Power supply 24Vdc. DAVR-Binary Output module 9203OB1A(UNC4662) No of Channels: 16 Input voltage: 20V to 23Vdc, 6mA Output Relay Contact rating: 250Vac/dc, 2A Isolation: Output to Output : 2KVac for 1 Min Input to Output: 2.5KVac for 1 Min Power supply 48Vdc.
Examen - (AAB01) Cuestionario1 - Conteste Las Preguntas Del Cuestionario 1 en Línea Referente Al Funcionamiento Del Computador y La Aritmética Del Computador