Professional Documents
Culture Documents
Crusher Backing Compound Introduction - S
Crusher Backing Compound Introduction - S
cn
www.edgebond.cn info@edgebond.cn
100% solid epoxy compound
www.edgebond.cn info@edgebond.cn
Specific Gravity (g/cm3) 1.64
Harness (Shore D) 80
www.edgebond.cn info@edgebond.cn
lFor PY cone crushers of domestic brands;
l F o r i m p o r t e d ( s u c h a s N o r d b e r g , S a n d v i , e t c . ) c o n e 、 g y r a t o r y c r u s h e r ’s
potting and filling between liner and cone body;
www.edgebond.cn info@edgebond.cn
Zinc base alloy
HP epoxy resin
www.edgebond.cn info@edgebond.cn
www.edgebond.cn info@edgebond.cn
High
shrinkage
www.edgebond.cn info@edgebond.cn
No
No falling
toughening Crispy off
modifying
www.edgebond.cn info@edgebond.cn
www.edgebond.cn info@edgebond.cn
www.edgebond.cn info@edgebond.cn
www.edgebond.cn info@edgebond.cn
www.edgebond.cn info@edgebond.cn
KorrobXX 65
www.edgebond.cn info@edgebond.cn
Standard temperature 2℃—8℃
EdgeBond EdgeBond
Brand KorrobXX 65 KorrobXX 65
6302 6302
Average
peeling
0.38 0.24 0.32 0.22
strength
(Mpa)
www.edgebond.cn info@edgebond.cn
Standard temperature
EdgeBond EdgeBond
KorrobXX65 KorrobXX 65
6302 6302
www.edgebond.cn info@edgebond.cn
EdgeBond KorrobXX EdgeBond KorrobXX
65 65
www.edgebond.cn info@edgebond.cn
KorrobXX 65
Component A Component A
XX 65
Benzyl alcohol
Component Benzyl glycidyl ether
4-Morphine aldehyde
Optimize hardness and
Silica powder Ethyl 1-methyl-2- compressive properties
methoxyacetate
www.edgebond.cn info@edgebond.cn
KorrobXX 65
Component A Component B
XX 65
95-97% 30-60%
It can improve the
cohesive force of the
adhesive, provide high
strength adhesion
without peeling off.
Diisopropylnaphthalene
Diethylenetriamine
isomer
Component
A good curing agent
Triethylenetetramine
ratio will also provide
Amine, polyethylene, just good adhesion, and
triethylenetetramine fraction the adhesive will not be
Phthalocyanine green
too brittle or too soft
after curing.
www.edgebond.cn info@edgebond.cn
Recommend to use power above 400W,
speed under 600/min, double hand, speed
adjustable dill & disk stirrer.
www.edgebond.cn info@edgebond.cn
l Mixing:
ü Open component A drum, stir about 1 minute by hand stirrer to make it even.
ü Shake component B, adding to component A while stir A continuously.
ü Mix up and down for 2-3 minutes, to make it in uniform color.
www.edgebond.cn info@edgebond.cn
l Pouring:
ü Pour immediately after mixing thoroughly.
ü Pour the liquid against one spot into gap between cone body and liner, to empty the air in
cavity.
ü May use iron sheet, paper, or clay as as pouring cofferdam, until gap is filled.
ü For 10kgs pack of material, finish mixing and pouring within 10 minutes.
www.edgebond.cn info@edgebond.cn
l Notice
ü Do not pour the un-thoroughly mixed liquid into cavity.
ü Working time is longer at low temperature. High viscosity is difficult to mix even and
pouring. Recommend to place material at 25℃ for 24h before using. Heating liner and
cone body to 10-25℃ when pouring。
www.edgebond.cn info@edgebond.cn
xxBond
3496
whether to add C based
on the colder and hotter
air temperatures Added C
Saturated Good
epoxy resin quality
materials
No price
increase
www.edgebond.cn info@edgebond.cn
www.edgebond.cn info@edgebond.cn
Locking
Sealing
Bonding
Cleaning
Anti- wear
Anti-
Corrosion
www.edgebond.cn info@edgebond.cn
www.edgebond.cn info@edgebond.cn
Plant equipment and workshop corner
www.edgebond.cn info@edgebond.cn
l Professional R&D, manufacture, and distribution
of adhesives and polymer interface materials in
China.
l Products broadly used in: industry, transport,
electronic, microelectronics, solar energy, wind
power, etc.
l Nationally renowned with strong base of
independent intellectual property rights.
www.edgebond.cn info@edgebond.cn
● Thank you for taking the time to review our company's product
introduction.
● If you are interested in this, please feel free to email us, and our technical
service team will answer any questions you are interested in.
● Te c h n i c a l S e r v i c e E m a i l : info@edgebond.cn
● Te l : + 8 6 - 7 5 5 - 2 8 2 8 7 2 1 9
www.edgebond.cn info@edgebond.cn