Professional Documents
Culture Documents
Ms 8236
Ms 8236
MS8236
FUNC RANGE MAX HOLD
TEST
mA
µA A
Phone
Ω Tone
V Net
Cable
OFF NCV
IEC61010-1
600V CAT III
VΩ
10A COM µAmA
01 02
03 04
05 06
LCD diagram
3. Specifications
V Volts (Voltage)
A Amperes (Current) 3.1 General
Hz Hertz (Frequency) 3.1.1 Auto range and manual range options are available.
μ,m, Symbols of units: micro, milli, kilo and million 3.1.2 Overload protection is available for all ranges.
k, M 3.1.3 Display: LCD.
Continuity buzzer 3.1.4 Maximum value display: 1999 digits.
Diode measurement 3.1.5 Polarity indication: automatic; ‘---‘ for negative
MAX Maximum measurement polarity.
H Reading being held 3.1.6 Over-range indication: ‘0L’ or ‘---0L’.
Low battery 3.1.7 Unit indication: function and energy unit indication.
3.1.8 Judging the ringing, standby or pick-up mode of
Phone standby the phone line.
Phone ringing 3.1.9 Judging any breakpoint in the cable line, and
Phone pick-up tracking the routing of the cable line.
07 08
09 10
11 12
13 14
4.8.1 Plug the black probe into the COM jack and the red 4.9.1 Plug the black probe into the COM jack and the red
probe into the V jack. probe into the V jack.
4.8.2 Set the range selector to the V range position. 4.9.2 Set the range selector to the V range position.
4.8.3 Press the “FUNC” key to switch to the DC 4.9.3 Press the “RANGE” key to select the auto or manual
measurement mode, and press the “RANGE” key mode.
to select the auto or manual mode. 4.9.4 Connect the test probes to the voltage source or load
4.8.4 Connect the test probes to the voltage source or in parallel for measurement.
load in parallel for measurement. 4.9.5 Take a reading in the main display area of the LCD.
4.8.5 Take a reading in the main display area of the LCD.
Note:
The polarity indication will show the polarity of the
terminal connected by the red probe. 1) At the low voltage range, unsteady readings will appear
before the test probes contact the circuit. This is normal
Note: because the meter is highly sensitive. When the test
1) At the low voltage range, unsteady readings will appear probes contact the circuit, the true reading will be
before the test probes contact the circuit. This is normal displayed.
because the meter is highly sensitive. When the test 2) In the manual range mode, if the LCD displays ‘O L’ only,
probes contact the circuit, the true reading will be it means the measurement has exceeded the range and
displayed. a higher range should be selected.
2) In the manual range mode, if the LCD displays “O L” 3) In the manual range mode, if the scale of the measured
or “-O L” only, it means the measurement has exceeded value is unknown beforehand, the highest range should
the range and a higher range should be selected. be set and then lowered down gradually.
15 16
17 18
19 20
21 22
23 24
WARNING
There is the risk of electric shock.
A voltage may still be present even if there is
no indication. Do not rely on the non-contact
voltage detection function to judge whether a
voltage is present on a shielded wire. The
detection operation may be affected by such
factors as socket design, insulation thickness
and type of wires.
Note:
1) If the cable under test has no shield, the shield symbol
will flash to indicate open circuit, which is normal.
2 ) If the line status changes, be sure to press "TEST" to
close the current test result and then press "TEST"
again to test the line status.
25 26
27 28
WARNING WARNING
Before opening the battery cover, remove the The test probes must be replaced with those
test probes from the circuit under test to avoid of the same model or class, and must be kept
the risk of electric shock. in good condition. Ratings of test probes:
To avoid fire hazards, be sure to use the CAT III 600V 10A.
designated fuse (at rated voltage, amperage If the insulation of any test probe is damaged, e.g., a wire
and blow rate). is exposed, the test probe must be replaced.
29 30
31 HYS006777-V2