Professional Documents
Culture Documents
Kurdestan 6000
Kurdestan 6000
Ms. Firouzshahi /
Issued for
00 08 / 19 / 2023
Review
HR. Hosseini
Rev. Date Description Prepared By Checked By Approved By Authorized By
Client Logo Client Name Consultant Logo
Table of Contents
1. Introduction...........................................................................................................................................................4
2. Technical Specification..........................................................................................................................................4
3. MATERIAL AND EQUIPMENT SUPPLY.................................................................................................................10
5. Note .....................................................................................................................................................................11
Client Logo Client Name Consultant Logo
1. Introduction
This document concerned technical Basic data for dust collection system (bag filter)
from…………………………………..., (various sections). The equipment will be installed in
………………………………………….
Client Logo Client Name Consultant Logo
2. Technical Specification
50 Impeller material - St 52
51 Shaft material - Ck45
52 Total efficiency % ~75
53 Inlet damper - Motorized
54 Vibration transmitter & Temp. Sensor for fan Pcs. 1 for each
55 Washing/Drainage nozzle Yes / No Yes
56 Required if the noise is
Silencer Pcs. more than 85db in 1m
distance
57 Inlet & outlet expansion joint Yes / No Yes
58 Inspection door Yes / No Yes
Bag
59 Quantity Pcs. 48
60 Fabric Material - Polyester
61 Diameter mm 160
62 Length mm 3500
63 Weight Gr/m2 500 – 600
64 Top Part - Snap Ring
Cage
65 Quantity Pcs. 48
66 Material - St37
67 Coating - Alkyd Primer (WFL)
68 Diameter mm 157
69 Length mm 3500
Venturi
70 Quantity Pcs. 48
71 Diameter mm 90 (WFL)
72 Material - St37
73 Thickness mm 1~2.5
Casing
Client Logo Client Name Consultant Logo
74 Material - St37
75 Thickness - 4 (WFL)
Hopper
76 Material - St37
77 Thickness mm 4
78 Angle of Slope Degree >60
79 Level Switch (High & Low) Pcs. 2
80 Type - Capacitive
Screw & Gear motor
81 Type - Through
82 Quantity Pcs. 1
83 Material - St37
84 Shaft Material - Ck45
85 Drive Type - Direct Coupling (VTC)
86 Length mm WFL
87 Speed Rpm 30
88 Gear Motor Power Kw 2.2
89 Service Factor - Max 1.2
90 Speed Switch Pcs. No
Slide gate
91 Type - Manual
92 Quantity Pcs. 1
93 Material - St37
94 Size mm WFL
Telescopic Chute
95 Size mm WFL
96 Open Length mm WFL
97 Close Length mm WFL
98 Winch Kw ~1.5
99 Service Factor - Max 1.2
Client Logo Client Name Consultant Logo
10
Motor Starting Method - DOL
0
Rotary & Gear motor
10
Quantity Pcs. 1
1
10
Material - St37
2
10
Shaft material - Ck45
3
10
Drive type - Direct Coupling
4
10
Size mm 250
5
10
Speed Rpm ≃30
6
10
Gear motor power Kw 1.1
7
10
Service Factor - Max 1.2
8
10
Speed switch Pcs. Yes
9
Storage bin
11
Capacity m3 WFL
0
11
Diameter mm WFL
1
11
Length mm WFL
2
11
Level switch Pcs. 1
3
11
Type - Capactive
4
11
Storage bin below the bag filter hopper - YES
5
11
Rotary valve / Slide gate - YES
6
11
Noise level limit db <85 db (A) in 1m distance
7
Stack
11 Stack Diameter mm WFL
Client Logo Client Name Consultant Logo
8
11
Stack Length mm WFL
9
12
Stack thickness mm WFL
0
12
Stack Material - St37
1
12
Access Platform - Included
2
12
Dust detector - Included
3
Ducting
12
Outlet Duct between outlet flange and fan Yes/No Yes
4
12
Duct between outlet Fan and inlet stack Yes/No Yes
5
12
Inlet & Outlet Flanged collector Yes/No Yes
6
12
Manual & Pneumatic damper Yes/No Yes
7
12
Material - St37 (VTC)
8
Motor
12
Quantity of Motor Pcs. 1
9
13
Rated Voltage V 400 ± 5%
0
13
Rated Frequency Hz 50 ± 5%
1
13
Motor Power Kw 15
2
13
Motor Speed Rpm 1500
3
13
Pole Pcs. 4
4
13
Motor insulation Class - Class F
5
13
Motor Temperature rise class - Class B
6
13 Motor Protection IP 55
Client Logo Client Name Consultant Logo
7
13
Service Factor 1.00
8
13
International Efficiency Class IE1/2/3/4 IE1
9
14
Max. Noise level db <85
0
3. MATERIAL AND EQUIPMENT SUPPLY
A‐ FOR BAG FILTER
Bag filter body and frame
In/out dampers
Bags
Bag cleaning system including: pulse jet system
Inlet /outlet expansion joints complete with flanges
Rotary valves.
Compressed air solenoid valves.
Compressed air injector
Compressed air reservoir
Related instruments including: differential pressure switch, pulse jet cleaning system
B‐ FOR FAN
Centrifugal fans
Fan housing & inlet box
Fan bearing
Motorized Inlet damper.
Inlet & outlet plenum matches with ducting drawing
Electric motors
Couplings and guards
Exhaust stack (inlet & outlet plenum matches with ducting drawing)
Inlet /outlet expansion joints complete with flanges
C‐ FOR SUCTION DUCTING
Client Logo Client Name Consultant Logo
Suction hoods
Ductwork with all related accessories
Duct Support with all related accessories
Inspection doors
Dampers (both manual and pneumatic)
5. NOTE:
1. WFL: Will be Finalized later