Professional Documents
Culture Documents
17 - X30596ELEC - 2013-10-15 Tsio-360
17 - X30596ELEC - 2013-10-15 Tsio-360
CB,D,DB,E,EB,
F,FB,GB,H,HB,
JB,KB,LB,MB
& SB
LTSIO-360-E,EB & KB
OVERHAUL
MANUAL
Available exclusively from the publisher: P.O. Box 90, Mobile, AL 36601
Copyright © 2011-2013 Continental Motors, Inc. All rights reserved. This material may not be reprinted, republished, broadcast, or otherwise
altered without the publisher's written permission. This manual is provided without express, statutory, or implied warranties. The publisher will
not be held liable for any damages caused by or alleged to be caused by use, misuse, abuse, or misinterpretation of the contents. Content is
subject to change without notice. Other products and companies mentioned herein may be trademarks of the respective owners.
The performance rules for replacement of parts and materials used in the maintenance and alteration of
U.S. certificated aircraft are specified in Federal Aviation Regulations (FAR) 43.13 and FAR 145.57. The
responsibility for the continued ailworthiness of the aircraft, which includes the replacement of parts, is the
responsibility of the owner/operator as outlined in FAR 91.163, FAR 121.363, FAR 123.45, FAR 127.131
and FAR 135.143 (a).
a. Byan FAA Form 8130-3 (Formerly FAA Form 186), Airworthiness Approval Tag. An Airworthiness
Approval Tag identifies a part or group of parts that have been approved by authorized FAA
representatives.
b. Byan FAA Technical Standard Order (TSO) number and identification mark that indicates the part or
appliance has been manufactured under the requirements of FAR 37.
c. Byan FAAIPMA symbol, together with the manufacturer's name, trademark or symbol, part number,
and the make and model of the type certificated product on which the part is eligible for installation,
stamped on the part. An FAA Parts Manufacturer Approval (FAAIPMA) is issued under FAR 21.305.
The make and model information may be on a tag attached to the part.
d. By shipping ticket, invoice, or other document which provides evidence that the part was produced
by a manufacturer holding an FAA Approved Production Inspection System issued under FAA 21,
Subpart F, or by a manufacturer holding an FAA Production Certificate issued under FAA 21, Subpart
G.
e. By a certificate of airworthiness for export issued by a foreign government under the provisions of
FAR 21, Subpart N.
11. KNOW YOUR SUPPLIER. It has come to our attention that many reproduced parts and
components, particularly instruments which have been manufactured by persons other than the original
manufacturer, are available for purchase and installation on U.S. certificated aircraft. Often, an original part
is used as a sample to produce duplicates. The reproduced parts appear to be as good as the original part;
however, there are many unknown factors to be considered that may not be readily apparent to the
purchaser, i.e., heat treating, plating, inspections, tests and calibrations. All too often the faulty part is not
discovered until a malfunction or an accident occurs.
12. SUM MARY. In accorda~ce with FAR's, certification of materials, parts, and appliances for return
to service, for use on aircraft, is the responsibility of the person or agency who signs the approval.
The owner/operator, as denoted in paragraph 3 of this advisory circular, is responsible for the continued
airworthiness of the aircraft. To assure continued safety in aircraft operation, it is essential that great care
be used when inspecting, testing, and determining the acceptability of all parts and materials. Particular
caution should be exercised when the identity of materials, parts, and appliances cannot be established
or when their origin is in doubt.
iii
OVERHAUL FOR
TSIO-360 SERIES
AIRCRAFT ENGINE
- NOTICE-
The overhauler must comply with all instructions contained in this manual in order to assure safe and
reliable engine performance. Failure to comply will be deemed misuse, thereby relieving the engine
manufacturer of responsibility under its warranty.
This manual contains no warranties, either expressed or implied. The information and procedures
contained herein provide the overhauler with technical information and instructions applicable to proper
overhaul procedures.
Prior to overhaul, the mechanic must meet requirements of Federal Aviation Regulation 65 and must
follow FAR parts 43, 91, and 145, as applicable. This manual must be used in conjunction with the FAA
Advisory circular 43.13-1A, Acceptable Methods, Techniques and Practices - Aircraft Inspection and
Repair, as well as Teledyne Continental Motors' TSIO-360 - Series Parts Catalog X30597A.
CHAPTER
1 Introduction
4 Airworthiness Limitations
70 Standard Practices
72 Engine, Reciprocating
74 - Ignition
75 Air
76 Engine Controls
77 Engine Indicating
78 Exhaust
79 Oil
80 Starting
81 Turbines
iv
INTRODUCTION
This Teledyne Continental Motors Overhaul Manual is prepared in accordance with the GAMA (General
Aviation Manufacturers Association) format. The manual is divided into groups which enable a broad
separation of contents, (Chapters) within each group.
The chapters are broken down into major systems, Engine - Reciprocating, Exhaust, Starting, etc. The
System Chapters are arranged alphabetically. All System Chapters are assigned a number which becomes
the first element of a standardized numbering system. The element "72" of the number series 72-00-00
refers to the System Chapter on "Engine Reciprocating." All information pertaining to the engine will be
covered in this System Chapter.
The major System Chapters are then broken down into Sub-System Sections. These sections are identified
by the second element of the standardized numbering system. The number "10" of the basic number
series "72-10-00" is for the "disassembly" of the engine.
The Subsection is the third element of the standardized numbering system "72-10-12." This number is the
final breakdown of the Chapter. Number "12" is for "Oil Pump Assembly," that is "Disassembled" from the
"Engine."
EXAMPLE:
- ) 72 - 10 - 12 -- '
In producing this publication, considerable effort has been put forth to provide grammatically clear and
accurate information. Teledyne Continental Motors solicits the users assistance in providing information
for review on changes that the user may suggest.
v
TABLE OF CONTENTS
SECTION PAGE AEROACHE
GRID NO.
NOTE ••• The following Section and Grid Numbers are located on Fiche 1 of 2.
CHAPTER I INTRODUCTION
1-00-00 SCOPE
1-00-01 Related Publications . 1-00-03 A21
1-00-02 Service Bulletins . 1-00-04 A22
1-00-03 Service Reports and Inquiries . 1-00-04 A22
1-00-04 100% Replacement Parts . 1-00-05 A23
1-20-00 TOOLS
1-20-01 Special Tools. 1-20-01 B13 - 02
1-30-00 PRODUCTS
1-30-01 Product List . 1-30-01 03-08
vi March 1989
SECTION PAGE AERORCHE
GRID NO.
March 1989 ix
SECTION PAGE AEROACHE
GRIONO.
CHAPTER 72-80 ENGINE PRESERVATION
NOTE ••• The following Section and Grid Numbers are located on Fiche 2 012.
CHAPTER 74 IGNITION
(TCM IGNITION SYSTEM)
CHAPTER 75 AIR
X March 1989
SECTION PAGE AERORCHE
GRID NO.
CHAPTER 78 EXHAUST
CHAPTER 79 OIL
79-00-00 GENERAL. . . . . . . . . . . . . .
. . ....... 79-00-03 G14
79-10-00 APPROVED OIL PRODUCTS. . . . . . . . ...... 79-00-03 G14
79-20-00 LUBRICATING SYSTEM TROUBLESHOOTING CHART. 79-00-04 G15
CHAPTER 80 STARTING
CHAPTER 81 TURBINES
March 1989 xi
LIST OF ILLUSTRATIONS
I 72-10-12C
72-10-13
Starter and Starter Drive Adapter,
TSI0-360-E,EB,F,FB,GB,KB,MB,SB LTSIO-E,EB,KB ...... .
Oil Pump Assembly ............................................................... .
72-10-33
72-10-35
G15
G17
72-10-14A Intercylinder Air Baffles,
I 72-10-14B
TSIO/LTSI0-360-D,DB,F,FB,GB,KB,LB,MB,SB ............... .
Cylinder and Piston Assembly .............................................. .
Crankcase Assembly ............................................................ .
72-10-37
72-10-38
72-10-41
Gi9
G20
G23
72-10-15
72-10-16 Camshaft Assembly .............................................................. . 72-10-42 G24
72-10-17 Crankshaft Group .................................................................. . 72-10-43 Hi
72-10-18A Exhaust Assembly LTSI0ITSI0-360-E,EB & KB ................. .. 72-10-45 H3
72-10-18B Exhaust Assembly TSI0-360-F,FB ...................................... .. 72-10-47 H5
•
72-10-18C Exhaust Assembly TSI0-360-GB & LB ................................. . 72-10-49 H7
72-10-18D Exhaust Assembly TSI0-360-MB & SB ............................... .. 72-10-50 H8
72-20-12A Crankcase and Accessory Case Stud Setting Heights ......... . 72-20-06 H16
NOTE .•• The following Figure and Grid Numbers are located on Fiche 2 of 2.
DECEMBER 1992 xv
LIST OF CHARTS
NOTE ••• The following Figure and Grid Numbers are located on Fiche 1 of 2.
NOTE ••• The following Figure and Grid Numbers are located on Fiche 2 of 2.
1-00-00 SCOPE
1-10-01 Abbreviations/Symbols
1-10-02 Definitions
1-20-00 TOOLS
1-30-00 PRODUCTS
1-00-01
INTENTIONALLY
LEFT
BLANK
1-00-02
1-00-00 SCOPE
Recommendations, cautions and warnings regarding overhaul of this engine are not
intended to impose undue restrictions. They are inserted to obtain maximum performance
from the engine in accordance with safety and efficiency. Abuse, misuse, or neglect of
any piece of equipment can cause eventual failure. For an aircraft engine, it is obvious
that a failure may have disastrous consequences. Failure to observe the instructions
contained in this manual constitutes unauthorized operation in areas unexplored during
development of the engine, or in areas which experience has proved to be undesirable or
detrimental.
NOTES, Cautions and Warnings are included throughout this manual. Application is as
follows:
NOTE. .. Special interest information which may facilitate the operation of equipment.
CAUTION. .. Information issued to emphasize certain instructions or to prevent possible
damage to engine or accessories.
WARNING ... Information which, if disregarded, may result in severe damage to or
destruction of the engine or endangerment to personnel.
It is recommended that the following parts be replaced 100 percent during the major overhaul
of any Teledyne Continental Motor's aircraft engine regardless of conditions.
Special Note:
If for any reason lifters are removed for inspection before the overhaul period has been
reached, they must be placed back in the same location from which they were removed.
Re-assembly with configuration as per Service Bulletin M76-10 and M83-10 Rev. 1 or current
revision as applicable at the time major overhaul is recommended.
1-OO-{)5
INTENTIONALLY
LEFT
BLANK
1-00-06
1-10-00 DEFINITIONS AND ABBREVIATIONS
1-10-01 ABBREVIATIONS/SYMBOLS
TERM EXPLANATION
A.B.C. After Bottom Center
ADMP Absolute Dry Manifold Pressure
Approx. Approximately
A.T.C. After Top Center
Bar. Barometric
B.B.C. Before Bottom Center
B.H.P. Brake Horsepower
BSFC Brake Specific Fuel Consumption
B.T.C. Before Top Center
FAA Federal Aviation Administration
CAR. Civil Air Regulations
C.G. Center of Gravity
c.f.m. Cubic Feet Per Minute
C.H.T. Cylinder Head Temperature
CCW Counterclockwise Rotation
CW Clockwise Rotation
0
Degrees of Angle
of Degrees Fahrenheit
EGT Exhaust Gas Temperature
Fig. Figure (Illustration)
Front Propeller End of Engine
ft. Foot or Feet
F.T. Full Throttle
FT-LBS Foot Pounds Torque
G.P.M. Gallons Per Minute
gms Grams
Hex Hexagon
H2O Water
Hg. Mercury
hr. Hour
1.0. Inside Diameter
IN-LBS Inch Pounds Torque
in. (") Inches
Left Side Side on which No's 2, 4, and 6 cylinders are
located. (Rear to Front)
Lbs. Pounds
Lockwire Stainless steel wire used to safety connections, etc.
100LL 100 Octane Low Lead Fuel
Man. Manifold, Manometer
Max. Maximum
Min. Minimum
30' Thirty minutes of angle (60' equal one degree)
N.P.T. National Pipe Thread (Tapered)
N.C. National Course (Thread)
N.F. National Fine (Thread)
NRP Normal Rated Power
OAT Outside Air Temperature
0.0. Outside Diameter
oz. Ounce
Press. Pressure
p.s.i. Pounds Per Square Inch
1-10-01
PSIA Pounds Per Square Inch Absolute
PSIG Pounds Per Square Inch Gauge
PPH Pounds Per Hour
Rear Accessory End of Engine
Rec. Recommended
Right Side Side on which No's 1, 3, and 5 cylinders are
located. (Rear to Front)
R.P.M. Revolutions Per Minute
Std. Standard
T80 Time Between Overhaul
T.D.C. Top Dead Center
T.LT. Turbine Inlet Temperature
Torque Force x lever arm (125 ft.-Ibs. torque = 1251bs.
Force applied one ft. from bolt center or 62-1/2 Ibs.
applied 2 ft. from center), etc.
1-10-02 DEFINITIONS
ADMP Absolute dry manifold pressure, is used in establishing a baseline standard of engine perfor-
mance. Manifold pressure is the absolute pressure in the intake manifold; measured in inches
of mercury.
Ambient A term used to denote a condition of surrounding atmosphere at a particular time. For
example; Ambient Temperature or Ambient Pressure.
BHP Brake Horsepower. The power actually delivered to the engine propeller shaft. It is called
brake horsepower because it was formerly measured by applying a brake to the power shaft of
an engine. The required effort to brake the engine could be converted to horsepower-
hence: "brake horsepower."
BSFC Brake Specific Fuel Consumption. Fuel consumption stated in pounds per hour per brake
horsepower. For example, an engine developing 300 horsepower while burning 150 pounds of
fuel per hour, has a BSFC of .5.
Cold Soaking Prolonged exposure of an object to cold temperatures so that its tempera-
ture throughout approaches that of ambient.
Critical Altitude The maximum altitude at which a component can operate at 100%
capacity. For example, an engine with a critical altitude of 16,000 feet
cannot produce 100% of its rated manifold pressure above 16,000 feet.
Density Altitude Altitude as determined by pressure altitude and existing ambient tempera-
ture. In Standard Atmosphere (lAS) density and pressure altitudes are
equal. For a given pressure altitude, the higher the temperature, the
higher the density altitude.
1-10-02
Dynamic Condition A term referring to properties of a body in motion.
Exhaust Back Pressure Opposition to the flow of exhaust gas, primarily caused by the size and
shape of the exhaust system. Atmospheric pressure also affects back
pressure.
Four Cycle Short for "Four Stroke Cycle." It refers to the four strokes of the
piston in completing a cycle of engine operation (Intake, Compression,
Power and Exhaust).
Fuel Injection A process of metering fuel into an engine by means other than a
carburetor.
Galling or Scuffing Excessive friction between two metal surfaces resulting in particles of the
softer metal being torn away and literally welded to the harder metal.
Hydrostatic Lock Inability or restriction of piston rotation at TDC due to fluid accumula-
tion in excess of combustion chamber displacement.
Impulse Coupling A mechanical device used in some magnetos to retard the ignition timing
and provide higher voltage at cranking speeds for starting.
Lean Limit Mixture The leanest mixture approved for any given power condition. It is not
necessarily the leanest mixture at which the engine will continue to
operate.
Major Overhaul Per FAA AC43-11 consists of the complete disassembly of an engine,
inspected, repaired as necessary, reassembled, tested, and approved for
return to service within the fits and limits specified by the manufac-
turer's overhaul data. This could be to new fits or limits or serviceable
limits. The determination as to what fits and limits are used during an
engine overhaul should be clearly understood by the engine owner at the
time the engine is presented for overhaul. The owner should also be
aware of any parts that are replaced, regardless of condition, as a result
of manufacturer's overhaul data, Service Bulletin, or an airworthiness
directive.
Manifold Pressure Pressure as measured in the intake manifold down-stream of the air
throttle. Usually measured in inches of mercury.
Mixture Mixture ratio. The proportion of fuel to air used for combustion.
1-10-03
Naturally Aspirated A term used to describe an engine which obtains induction air by drawing
(Engine) it directly from the atmosphere into the cylinder. A non-supercharged
engine.
Oil Temperature Control A thermostatic valve used to divert oil through or around the oil cooler,
Valve as necessary, to maintain oil temperature within desired limits (ref.
vernatherm valve).
Overboost Valves A pressure relief valve, set slightly in excess of maximum deck pressure,
to prevent damaging overboost in the event of a system malfunction.
Overhead Valves An engine configuration in which the valves are located in the cylinder
head itself.
Performance Rating A rating system used to describe the ability of fuel to withstand heat and
pressure of combustion as compared with the 100 octane fuel. For
example, an engine with high compression and high temperature needs a
higher Performance Rated fuel than a low compression engine. A rating
of 100/130 denotes performance characteristics of lean (100) and rich
(130) mixtures respectively.
Pressure Altitude Altitude, usually expressed in feet, (using absolute static pressure as a
reference) equivalent to altitude above the standard sea level reference
plan (29.92: Hg. Standard).
Propeller Load Curve A plot of horsepower, versus RPM, depicting the power absorption
characteristics of a fixed pitch propeller.
Propeller Pitch The angle between the mean chord of the propeller and the plane of
rotation.
Rated Power The maximum horsepower at which an engine is approved for operation.
Retard Breaker A device used in magnetos to delay ignition during cranking. It is used
to facilitate starting.
Rich Limit The richest fuel/air ratio permitted for a given power condition. It is
not necessarily the richest condition at which the engine will run.
Rocker Arm A mechanical device used to transfer motion from the pushrod to the
valve.
1-10-04
Run Out Eccentricity or wobble of a rotating part.
Scavenge Pump A pump (especially an oil pump) to prevent accumulation of liquid in some
particular area.
Sonic Venturi A restriction, especially in cabin pressurization systems, to limit the flow
of air through a duct.
Sump The lowest part of a system. The main oil sump on a wet sump engine
contains the oil supply.
T.D.C. Top Dead Center. The position in which the piston has reached the top
of its travel. A line drawn between the crankshaft rotational axis,
through the connecting rod end axis and the piston pin center would be a
straight line. Ignition and valve timing are stated in terms of degrees
before or after TOC.
Thermal Efficiency Regarding engines, the percent of total heat generated which is converted
into useful power.
Turbo Supercharged A term used to describe an engine which obtains induction air by drawing
(engine) it directly from the atmosphere into the Turbocharger Compression Inlet,
compressing the air and routing it to the pressurized induction system.
Vapor Lock A condition in which the proper flow of a liquid through a system is
disturbed by the formation of vapor. Any liquid will turn to vapor if
heated sufficiently. The amount of heat required for vaporization will
depend on the pressure exerted on the liquid.
Variable Pressure A device used to control the speed, and thus the output of the
Controller turbocharger. It does so by operating the wastegate which diverts more,
or less, exhaust gas over the turbine.
1-10-05
Vernatherm Valve A thermostatic valve used to divert oil through or around the oil cooler,
as necessary, to maintain oil temperature within desired limits.
Volumetric Efficiency The ability of an engine to fill its cylinders with air compared to their
capacity for air under static conditions. A "naturally aspirated" engine
will always have a volumetric efficiency of slightly less than 100%,
whereas superchargers permit volumetric efficiencies in excess of 100%.
Wastegate Valve A unit, used on turbocharged engines, to divert exhaust gas through or
around the turbine, as necessary to maintain turbine speed. As more air
is demanded by the engine, due to throttle operation, the compressor
must work harder. In order to maintain compressor and turbine speeds,
more exhaust must be flowed through the turbine. The wastegate valve
closes and causes gas, which would go directly overboard, to pass through
the turbine. The wastegate is usually operated by an actuator which gets
necessary signals from the turbocharger controller.
DEFINITION OF TERMS
Front, rear, left, and right, as used in this manual, refer to the engine as viewed by the
mechanic in a normal position, facing the accessory end. Accessory end being the rear and
propeller flange being the front of the engine. Cylinders are numbered starting from the rear,
with odd numbers on the right and even numbers on the left.
Prefix - - - - - - - - -
1- Fuel Injection
0- Horizontally Opposed
Cylinder Configuration The MB Letter Identifies
The Model of Engine
Displacement
1-10-06
1-10-04 BASIC DESIGN FEATURE
The TS10-360 Series engines are air cooled, having six horizontally opposed overhead inclined
valve cylinders. The cylinder displacement of 360 cubic inches is achieved with a 4.44 inch
bore and a 3.88 inch stroke. The TS10-360 engines are turbosupercharged and have a 7.5 to 1
compression ratio. The TS10-360 series is fuel injected with an up-draft runner induction
system. The crankshaft is equipped with pendulum type counterweight dampers that suppress
torsional vibrations.
The TS10-360 engines have a doweled six bolt hole configuration propeller flange. A mounting
pad is provided to utilize a hydraulic controlled governor for the constant speed propeller.
The TS10-360 series engines are of a wet sump design with a positive displacement oil pump
installed in the lower portion of the accessory case. The desired oil pressure is maintained by
a pressure relief valve located on the left side of the accessory case. Engine cranking is
accomplished by a geared right angle drive starter adapter and a direct current starter motor.
The oil cooler is installed on the left rear side of the crankcase rearward of the NO.2
cylinder. The engine is equipped with two gear driven magnetos. The exhaust system mayor
may not be supplied with the engine by the engine manufacturer depending on the particular
engine model.
1-10-07
INTENTIONALLY
LEFT
BLANK
FIGURE 1-10-04
THREE-QUARTER RIGHT REAR VIEW OF THE TSIO-360 SERIES ENGINE
1-10-09
INTENTIONALLY
LEFT
BLANK
1-10-10
FIGURE 1-10-04
INSTALLATION DRAWING
DIMENSIONS
MODELS A B C D E F G H I
TSIO-360
A,AS 35.34 33.03 22.43 16.33 13.74 -- - --- ---
S,BS 35.34 33.03 22.43 16.33 13.74 -- -- -- --
C,CS 35.34 33.03 22.76 16.33 13.74 -- --- - ---
D,DS 35.34 33.03 22.76 16.33 13.74 -- --- --- ---
E,ES -- - -- 16.33 14.12 26.44 56.58 17.38 31.30
F,FS -- -- - 16.33 14.12 --- --- --- ---
GS --- - -- 16.33 14.12 32.34 42.78 17.38 31.38
H,HB 32.93 33.03 22.52 16.33 14.12 -- -- --- ---
JS 32.93 33.03 22.52 16.33 14.12 --- -- --- ---
KS -- - - 16.33 14.12 26.44 56.58 17.38
LS
MB/SS
-
--
--
-
--
-
16.33
16.33
14.12
14.12
32.34
32.82
42.78
42.78
17.38
17.38
31.38
34.37
REVISED OCT 97 1-10-11 •
INTENTIONALLY
LEFT
BLANK
1-10-12
1-20-00 TOOLS
The mechanic should be equipped with a complete set of common tools to include the minimum
of:
*Must be currently calibrated, and the calibration must be traceable to the National Bureau of
Standards.
Specific tools illustrated or similar tools marketed by other manufacturers are necessary for
service and maintenance of the aircraft engine. Tool illustrations shown on the following
pages are used with the permission of the respective manufacturers.
Illustrations in this section show only the general appearance of tools and do not correspond
to the actual size or shape. Details of special tools, fixtures, equipment and consumable
materials appropriate to overhaul procedures are listed in the various chapters and subsystems
of this manual; the following information is primarily for procurement purposes.
The following special tools are for All the Teledyne Continental Engines for the purpose of
convenience. To determine which tools are needed for your particular engine, refer to
"Special Tool Index."
1-20-01
SPECIAL TOOLS
PROCUREMENT SOURCES
GENERAL PRODUCT
COMPANY SUMMARY
ALCOR
Box 32516 Instruments for
10130 Jones Maltsberger Rd. Light Powered Aircraft
San Antonio, TX 78284 Special Tools
512/349-3771
SNAP ON TOOLS
2611 Commerce Blvd. Precision Tools
Birmingham, Alabama 35210 . Special Tools
205/956-1722
1-20-02
-- NOTICE --
All tools referenced under SUb-section 1-20-01 Special Tools, are for reference only, not for the purpose
of promoting or suggesting tools to be purchased from the indicated sources.
EXAMPLE: The Supplier Identifier Code is shown in the lower right-hand corner of the applicable
tool photograph.
CODE SUPPLIER
CODE
@ Numbers referenced in the left-hand bottom corner of each photograph correspond to the
numbers located in the Special Tool Index.
WARNING ••• Whenever using test equipment keep equipment and personnel clear of prop area.
1-20-03
SPECIAL TOOLS
1-20-04
Item & Nomenclature Application Vendor
Part Number
1-20-05
Item & Nomenclature Application Vendor
Part Number
1·20-06
Item & Nomenclature Application Vendor
Part Number
1-20-07
Oil Filter Can Cutter
(CT-470)
o
Strap Wrench
a. Insert threaded adapter in female threads of
For removal of oil filter, spring steel band filter, or screw rotating bushing on male
surrounds and tightens as the handle is pulled. threads of filter.
Vinyl gripped handle swivels to clear obstruc-
tions. b. Slightly tighten cutter blade against filter
and rotate 360 0 . Repeat operation until
GA333 for 3" to 3-3/8" Dia. Filters mounting plate section separates.
GA340 for 3-1/2" to 3-7/8" Dia. Filters
YA 341 for 4-1/8" to 4-7/16" Dia. Filters c. Lift mounting plate to expose complete filter
media for inspection.
Oil Filter
Sludge Inspection
Inspection of engine sludge trapped in spin-on
oil filters has been a recommended practice for
many years. Licensed aircraft mechanics recog-
nize the value of visual inspection to aid in
determining if internal engine wear or malfunc-
tion has occurred, and to inspect for metal or
other contaminates within the engine oil system.
3) Using a clean plastic bucket containing
Use of the Champion CT -470 Oil Filter Can approximately 1 pt. clean varsol, swish filter
Cutter eases the opening of spin-on filters element around in the varsol to loosen
without introducing foreign material into the entrapped metal or other contaminant.
filter.
4) Using a clean magnet, work it around in the
Following is the recommended procedure for varsol solution. Ferrous metal particles in
inspection of full flow oil filters: the solution should adhere to the magnet for
inspection.
1) Remove filter from the engine and place on
a drain tray. Allow oil to drain through a 5) After all ferrous metal particles have been
clean cloth to determine if foreign material retrieved by the magnet, pour remaining
drains from the filter. varsol through another clean shop rag, and
in a bright light, any non-ferrous metals
2) Using the Champion CT-470 Can Cutter, should be detectable.
open the filter as follows; (See photos):
1-20-08
Cylinder Base Nut Wrenches
3882 Series
The 3882 Series Wrenches feature 1/2" square
drive and 12-point hex sockets. The wall
thickness between the hex and wrench 0.0. is
closely controlled for maximum strength.
Approx. 16" long overall.
(3882-style shown in
Cylinder Base Nut Wrench
~hantom, to scale)
Special modified 3882-type wrench, this special
wrench is perfect for those occasional situations
when the 3882 wrench won't fit. It's a slightly
"~ I
' ... "'---------"\
different configuration, as shown.
80799/16" hex
1-20-99
Holding Fixture
Adapters
With these adapters, you may bolt the cylinder 5221-17A Cylinder
onto the 5221 B Fixture in order to do:
Holdown Clamp
Assembly (one req'd.
Cylinder Honing fits all adapters).
Valve Seat Insert Work (insert removal, Order separately.
seat cutting, insert installation).
Universal Cylinder
Holding Fixture 5221 B
This is a heavy-duty, preCision fixture manu-
factured to extremely close tolerances. Suitable
for use on vertical mills or drill presses, it
allows quick indexing of required angles for
valve work.
FEATURES:
1-20-10
Valve Guide Cleaner 122
Expandable type fits all Continental engines.
(Heat-Shrink Type)
1-20-11
Valve Guide Replacers
Alloy steel. heat-treated for maximum
toughness.
~~~tj
Driver and Pilot Ram Replaces
Adapter Assy. Dia. Dia. Tool
gu§§ ~
8118G .731 .871 7233
8118H .706 .808 S007/2881-1
8118J .S93 .699 4904
8118K .S73 .714
Tapered Type
1-20-12
3170 - Floating holder
Valve Spring
Compressor 3602
3602
Adjustable type works on all Continental in use
engines.
Set includes:
* Instructions
* Storage case.
Tool is rigged for removal. Center is plugged to route water Tool is rigged for replacement. Guide on end of tool slips
out thru small holes in rim of removing head. into valve stem hole for perfect alignment. No more cocked
seats.
Fig. 1.
Fig. 2.
Installer
Valve Seat Inserts
4910 -For 1-45/64" 0.0. Exhaust and 1-53/64"
0.0. Intake Inserts.
(Includes head and handle)
1-20-14
8116 Common Parts Kit
Does not include Expanding Guide Bodies or
cutting tools. See below.
1-20-15
Valve Stem Hole Reamers
(Takes the place of 2847,3606 & 4913
Series reamers).
Tool No. Hole Dia.
8116.24 .344
8116.25 .375
8116.27 .436
8116.29 .438
ij] JD
Reamers Boring Bars
@ Tool No. Hole Dia.
@ ~ Hole Dia.
(*Example: Use 8116-6B Boring Bar to bore hole to .555, then finish with 8116-
6R Reamer to .561 dia.)
Straight Side
Cutters
Finish Finish
Part No. ~ Dim. O.S. ~ ~ Dim. O.S.
4909-8 Int 1.822 .010" 4985-5 Int 2.140 .030" Step Side
4909-9 Int 1.814 .002" 4985-6 Exh 1.669 .005" Cutters
4909-12 Exh 1.689 .002" 4985-7 Exh 1.664 .010"
4909-13 Exh 1.697 .010" 4985-8 Exh 1.669 .015" @
4954-5 Int 1.880 .005" 4985-9 Exh 1.674 .020"
4954-8 Int 1.885 .010" 4985-10 Exh 1.684 .030" Small Large Small Large
4954-9 Int 1.885 .002" 5224-5 Int 2.522 .005" Part No. Diameter Diameter ~ ~ Diameter Diameter .Q&
4954-10 Int 1.895 .020" 5224-10 Int 2.527 .010"
4954-11 Int 1.905 .030" 5224-15 Int 2.523 .015" 8135 1.654 1.884 STD 8138-3 1.803 2.070 .015"
4954-12 Exh 1.752 .002" 5224-20 Int 2.537 .020" 8135-1 1.659 1.884 .005" 8136-4 1.808 2.070 .020"
4954-13 Exh 1.760 .010" 5224-30 Int 2.547 .030" 8135-2 1.664 1.884 .010" 8138-S 1.818 2.070 .030"
4954-14 Exh 1.770 .020" 5225-S Exh 1.793 .005" 8135-3 1.669 1.884 .01S" 8138 2.271 2.632 STD
4954-15 Exh 1.780 .030" S225-1 0 Exh 1.798 .010" 8135-4 1.674 1.884 .020" 8138-1 2.276 : 2.632 .005"
11
4985-1 Int 2.115 .005 5225-15 Exh 1.808 .01S" 8135-5 1.684 1.884 .030" 8138-2 2.281 2.632 .010"
4985-2 Int 2.120 .010" S225-2O Exh 1.808 .020" 8136 1.788 2.070 STD 8138-3 ·2.286 2.632 .01S"
4985-3 Int 2.12S .015" S225-3O Exh 1.818 .030" 8136-1 1.793 2.070 .005" 8038-4 2.291 2.632 .020"
4985-4 Int 2.130 .020" 8136-2 1.798 2.070 .010" 8138-S 2.301 2.632 .030"
1-20-17
Connecting Rod Reaming and
Alignment Checking Fixture
With these precision tools, It's easy to check
connecting rods (without bushings) for
alignment and warpage.
Adapter Kits
These kits contain the indicator gauge assembly,
which as a dial Indicator reading In ten-thou-
sandths of an Inch (.0001"). The gauge body Is
lapped Into the mating bushing for accurate Complete tool combining
readings. Instructions are included. 8111 A Base with one of the 3
listed adapter kits shown
Adapter Kits checking rod for alignment.
8042C for 520-470-E Series 1.125"
8072C for 0-200, 0-300,360 1.00" & .922"
1-20-18
Universal Connecting Rod Bushing
Remover and Installer Set 8098
Complete set for removing and installing con-
necting rod bushings for Continental Support
bushing reverses for either installing or
removing.
e=-------~
Common Drive Handle 8122A -------=0.
This Drive Handle fits all pilots and cutters, 8122A Common
and it features positive pin drive as shown. Drive Handle
(Combination of Morse taper and pin drive
eliminates any slippage between handle and This handle fits all
cutter.) pilots and cutters (also
fits your old cutters).
By using the 8122A with the proper pilot from
below, you may choose to pilot into valve stem
hole or valve guide boss. W_l~/______~~
Pilots 8122A Handle / Pilot
Cutter
All pilots are hardened and precision ground for
accuracy. Two choices- pilot into valve stem
hole or valve guide boss.
o
Pilot Choice No. 1- Pilot Into Valve Stem Hole t::i\ Pilots
(On new Installations only) ® Pilot Choice No. 2 - Pilot Into Valve Guide Boss
Part No. Pilot Dia. Part No. Pilot Dia. Application Pari No. Pilot Dia. Application
-8123
- -.530- Standard
-8129
- -.624- Standard
8139 .343 8124 .535 Oversize .005 8130 .629 Oversize .005
8410 .374 8125 .540 Oversize .010 8131 .634 Oversize .010
8141 .435 8126 .545 Oversize .015 8132 .639 Oversize .015
8127 .550 Oversize .020 8133 .644 Oversize .020
8128 .560 Oversize .030 8134 .654 Oversize .030
CAUTION: DO NOT USE ON WORN GUIDES!
1-20-19
Needle Bearing Installers
Precisely machined to make bearing installation
fast.
8077A Includes:
Counterweight ~ushing
Remover/Installer
8077C
Positive guide of all components assures perfect
alignment. Includes adapters for 0-300, 360,
470 and 520 Series engines.
1-20-20
All Position Engine Stand
Assembly-Disassembly
Transportation 8104
Designed to save time on the overhaul floor.
Minimum attaching hardware allows complete
engine accessibility.
1-20-21
Cylinder Heating Stand 8156
Cylinder Risers
In just 8-10 minutes, you can heat 2 cylinders
simultaneously to 6OO 0 F. Or, you can heat one
Controls
at a time (each tip is separately controlled).
36" Hoses ~-t-rJ Y -Connector
Included with the 8156 Cylinder Heat Stand: w/fittings ~iN.--J
Regulator
(2) Tips
(2) 36" Propane Hoses w /fittings
(1) Propane Regulator
(2) ,Controls
(1) Y-Connector
(1) Stand Standard
(2) Cylinder Risers 20 lb. Propane Tank
1-20-22
Differential Pressure 7251
Cylinder Checker
Use standard shop air pressure to check
condition of rings, cylinder walls and valves.
1-20-24
Vacuum Pump 8334
This new heavy-duty vacuum pump is designed
for one-hand operation. Heavy steel wall; 0-30
in Hg; nozzle fits several sizes of tubing.
1-20-25
Spark Plug Insert Remover 4919
Use on all engines.
Stud Drivers
Six (6) different thread sizes:
1-20-26
Propeller Shaft Oil Seal Installer
5209
For all flanged shafts. For installing one piece
stretch seals without damaging sealing surfaces.
Be sure to oil the seal before installing.
(Dial indicator
not included)
1-20-27
Injector Nozzle
Remover and Installer 8165
This tool allows you to remove, install and
tighten Injector nozzles located close to intake
parts on Piper Aircraft. Torque Wrench exten-
sion allows use of 3/8" square drive torque
wrench to tighten nozzles to proper
specifications.
1-20-28
®
Pullers
These pullers provide a more controlled method to remove
press-fit parts.
o 0
1079 1063
1-20-2G
INSPECTION INSTRUMENTS
Outside M icrometers*
Spherical Anvil Micrometers are specially useful
in measuring the wall thicknesses of small parts
such as sleeves, collars, tubings and various
cylindrical workpieces. They are also used to
measure dimensions from inside of holes to
outside edges.
115-153
545-116
*All precIsion measuring devices must have a
current calibration and that calibration must be
traceable to the National Bureau of Standards.
1-20-30
Blade Micrometers*
Non-Rotating Spindle TYPE 122, 222
Screw Thread*
Micrometers
FOR MEASURING PITCH DIAMETERS
TYPE 126, TYPE 226
Interchangeable V-Anvil Type
Depth Micrometers*
The Depth Micrometer is one of the basic
measuring tools selected by machinists.
159-211
*All precIsion measuring devices must have a
current calibration and that calibration must be
traceable to the National Bureau of Standards. @
1-20-31
( R
4903-1- .645" Roughing (.609" Pilot) 5129-1- .753" Roughing (.718" Pilot)
4903-2- .680" Roughing (.643" Pilot) 5129-2- .788" Roughing (.751" Pilot)
4903-3- .703" Finishing (Use with 4903-1 5129-3- .813" Finishing (Use with
& 4903-2) (.678" Pilot) 5129-1 & 5129-2) (.786" Pilot)
4903-4- .708" Finishing (Use with 4903-1 5129-4- .818" Finishing (Use with
4903-2 & 4903-3) (.701" Pilot) 5129-1 &5129-3) (.815" Pilot)
4903-5- .723" Finishing (Use with 4903-1, 5129-5- .833" Finishing (Use with
4903-2,4903-3 & 4903-4) 5129-1,5129-2,5129-3 &
(.706" Pilot) 5129-4) (.815" Pilot)
"-::ti§iiR H
USE MORSE
ADAPTER
1-20-32
Engine Application Chart For Valve Guide Stem Hole Reamers
REAMERS USE
MORSE
CARBIDE- HIGH-SPEED CUTTING PILOT ADAPTER
TIPPED STEEL DIA. DIA. NO.
Plug Gauges,
Valve Guide Stem Hole
Go and No-go Gauges are used to check
for new limits (and service limits
where applicable). Gauges are heat-
treated alloy steel, precision ground.
1-20-33
Dial Thickness Gage*
For use in measuring wall thickness in hard to
reach areas.
7308
600 R-30
Inside Measuring*
Instruments
Three measuring surfaces are lapped parallel to @
the longitudinal axis of the Micrometer, and
stay aligned with the bore while measurements
are taken.
1-20-34
Alternator Analyzer
Voltage Regulator Tester
For field or bench use
EASY TO USE
Alternator/Regulator/
Battery Tester
Model E100
-t~
.......,......
~.. ~
Model E10 o
matter of minutes.
1-20-36
High Tension Lead Tester Kit
PIN 11-8950-2
1-20-37
CYLINDER HEAD TEMPERATURE
EXHAUST GAS TEMPERATURE
TEST UNITS
Alcor Portable
Digital EGT Unit
For use with Type "K" Thermocouple. This
device is lightweight 9 volt LCD unit, with a
disposable battery.
Alcor Portable
Digital CHT Unit
This device is used with Type "J" Thermocouple.
It is a lightweight 9 volt LCD unit, with
disposable battery.
1-20-38
APPLICATION CHART
SEALANTS/LUBRICANTS
ITEM
NO. TYPE/PART NUMBER APPLICATION MODELS REMARKS
______ a ___
• All ACC Drive Splines and All
Couplings Models
2 • Crankshaft Bearings
Oil - Grade 50. MHS 27
(CITGO. Inc) • Connecting Rod Bearings
• Prop Driver. Driven Gears All -_
..... .._......
and Bearings Models
• Camshaft Bearings
• Accessory Spur Gear Teeth
• Quill Shaft Splines
• Prop. Gov. Trans. Collar
and Sleeve
• Starter Cone. Bushing and
Nut
• Starter Clutch Spring (I.D. &
(Cont'd) 0.0.)
1-30-01
ITEM
NO. TYPE PART NUMBER APPLICATION MODELS REMARKS
2 • Pistons, Piston Pins, Piston See ----------
(cont'd) Oil - Grade 50, MHS 27 Rings Remarks
(CITGO, Inc.)
• Rocker Arms, Pivots, Valves
and Tappets
• Fuel Connections to Carbo See 6-285 & 6-320
(male threads only) Remarks
• Thrust Washer
• Oil Filter Adapter Seals All Models ---------
• O-Rings
• Connecting Rod Nuts -
Tiara engine only)
Alvania
5
(Shell #2)
• Oil Seal Lips Only All Models ---------
7
Permatex Aviation Grade 3D • Crankcase Parting Face All 360 _._....-----
(Permatex, Inc.) and see figure 72-20-00 for Models
#641543 Silk Thread Crankcase Threading Pro-
cedure.
and
#646942 Gasket Maker • Scavenge 011 Pump Covers All Models ------_..
1-30-02
ITEM
NO. TYPE PART NUMBER APPLICATION MODELS REMARKS
8 #646942 - Gasket Maker • Starter Adapter Assembly to See 520 Permold Models
(use alone on models listed) Crankcase. (Apply thin coat Remarks only
to adapter). 0-470G,
10-470C,J,H,N,K,
"'~MOTORS
"'" • Sump to Crankcase. (Apply See 10-520B,BA,BB,NB,N
Amott PIOductS
thin coat to oil sump). Remarks TSI0-520D,DB,UB &
10-550B
#646942 - Gasket Maker and • Sump to Crankcase with See All Models with
Gasket Gasket (Apply thin coat Remarks Sump Gasket.
between gasket and sump)
10 #642188-1 - Gasket Sealant • All Gaskets - Both Sides Ex- See Tiara 6-285 6-320
(TCM) cept Magneto Gasket Remarks
1.5 oz. tube
"'CON1lt\£N'W.
"'"
TEL.EJ:rft£
MOTORS • Rocker Cover Gaskets See For All Stamped
Amott PIOductS
(cover side) Remarks Covers
See
• Gasket - Idler Pin Remarks Models 470, 520 &
GTS I0-520
• Gasket -Intake Manifold
• Oil Drain Back Tubes
Sump to Crankcase
• All Press Type Plugs (Hub-
bard (etc) In Parting LIne See or Sump to Crank-
Area of 3-way Joints Remarks case to Acc Case
Models TS10360A,
• Oil Seal Accessory Drive AB,C,CB,D,DB
(OD only) 10360C,CB,G,GB
1-30-03
ITEM
NO. TYPE PART NUMBER APPLICATION MODELS REMARKS
10 #642188-1 - Gasket Sealant 8 2 Bolt SUction Tube Gasket See All 470 &520
(TCM) - Both Sides Remarks Models
(cont'd) 1.5 oz. tube
!
11 #646941 - High Strength 8 Rocker Cover Stud, Rocker Tiara Only
Adhesive Sealant Arm Pivot See
Remarks
8 Studs, Push Rod Retainerm All Models
Stud Break-A-Way
Torque 100 In/Lbs
8 Cylinder Deck Studs After 2 Hrs
Use With
"'""
'T'El.Et1iNE
cotlT1N3'ro\L MOTORS
Akcra1t I'IodI.Ic;ts
8 Engine Mount Studs & See 360 Models
Class 3 Studs in Accessory Remarks
Cover
12 #646940 - F/1 Sealant 8 All Pipe Thread Fittings in All Models Use Sparingly on
Fuel Injection System Male Threads Only
1-30-04
ITEM
NO. TYPE PART NUMBER APPLICATION MODELS REMARKS
15 CRC 336 Rust Prevention • Spray Exhaust End of All Turbo After Engine Test
Compound Turbocharger Charged
CITGO, Inc. Engines
17 Pipe Sealant - Loctite • Use on All Pipe Threads All Models .......-_........
(Teflon PSrr) Except as Noted
RELEASEAGEN, INC.
19 Oil Grade 50, MHS 27 • Cylinder Studs and Thru All Models Lube Threads Before
Bolts Tightening Nuts
21 TCM PIN 626531-1 • High Temp. Paint for All Models 72-30-13
Enamel - Gold (1 qt) Cosmetic and Corrosion Application
Protection
TCM PIN 626531-2 Available Thru
Enamel- Gold (1 gal) Teledyne
Continental Motors
1-30-05
INTENTIONALLY
LEFT
BLANK
1-30-06
CHAPTER 4
AIRWORTHINESS LIMITATIONS
This Airworthiness Limitations section has been FAA approved and specifies maintenance required
under §§ 43.16 and 91.403 of the Federal Aviation Regulations unless an alternative program has
been FAA approved. Federal Aviation Regulations §§ 43.16 and 91.403 require owner/operator
compliance with all maintenance limitations in this section concerning mandatory replacement times,
inspection intervals and other related procedures that are specific to this engine. Any such
limitations listed below are part of the design limits of the engine and the engine was type certificated
based upon required owner/operator compliance with the limitations.
1. Mandatory Replacement Times.
Subject to additional information contained in FAA Airworthiness Directives (AD) issued after the
date of certification, the engines covered in this manual do not contain any components having
mandatory replacement times required by type certification.
2. Mandatory Inspection Intervals.
Subject to additional information contained in FAA Airworthiness Directives (AD) issued after the
date of certification, the engine does not require specific intervals of inspection pursuant to type
certification.
3. Other Related Procedures
Subject to additional information contained in the Airworthiness Directives (AD) issued after the
date of certification, there are no other related procedures required pursuant to the type
certification for this engine.
4. Distribution of Changes to Airworthiness Limitations.
Changes to the Airworthiness Limitations section constitute changes to the type design of this
engine and require FAA approval. Such changes will be published in FAA Airworthiness
Directives (AD).
NOTE
The limitations in this section apply only to specific limitations which are part of the engine design.
Under the Federal Aviation Regulations numerous other additional limitations are applicable to this
engine and it's accessories. For example Federal Aviation Regulation Parts 91 and 43, among other
parts, define inspection criteria, maintenance requirements and procedures that are applicable to
this engine. It is the responsibility of the owner / operator to maintain the engine in an airworthy
condition by complying with all applicable Federal Aviation Regulations and by performing
maintenance in accordance with TCM Instructions for Continued Airworthiness, which consist of
TCM publications and service documents.
5-00-00 GENERAL
5-00-01
INTENTIONALLY
LEFT
BLANK
5-00-00 GENERAL
WARNING ... When performing any inspection or maintenance, always treat the engine as if
the ignition switch was on. Do not stand, nor allow anyone else to stand, within the arc of
the propeller, since a loose or broken wire, or a component malfunction, could cause the
engine and propeller to rotate and/or start.
5-00-03
INTENTIONALLY
LEFT
BLANK
5-10-00 TIME LIMITS/INSPECTION PROGRAM.
The owner or operator is responsible for maintaining the engine in an airworthy condition,
including compliance with all applicable Airworthiness Directives as specified in Part 39 of the
Federal Aviation Regulations and "Airworthiness Limitation" of this manual per FAR A33.4. It
is also the responsibility of the owner or operator to insure that the engine is inspected in
compliance with the requirements of Parts 43 and 91 of the Federal Aviation Regulations.
Teledyne Continental Motors has prepared this inspection guide to assist the owner or
operator in meeting their responsibilities. This inspection guide is not intended to be all-
inclusive; no guide can replace the good judgement of a certified airframe and power plant
mechanic in the performance of his duties. As the one primarily responsible for the airwor-
thiness of the airplane, the owner or operator should select only qualified personnel to
maintain the airplane.
CAUTION. . . Use only oils conforming to Teledyne Continental Motors Specification MHS24
or MHS25 after break-in period.
*NOTE. . . Hours stated or 6 months, whichever comes first. See latest Fuels & Oils Service
Bulletin.
5-10-01
INTENTIONALLY
LEFT
BLANK
5-10-02
5-20-00 SCHEDULED MAINTENANCE
Refer to Service Bulletin M-86-6R1, or current revision as applicable.
Before each flight the engine and propeller should be examined for damage, oil leaks, proper
servicing and security. Refer to the airframe manualOOPreflight Check List".
Record any values not conforming to engine specifications so that necessary repair or
adjustment can be accomplished.
11. Adjustments & Repairs: Perform service as required on any items that are
not within specifications.
12. Engine Condition: Run up and check as necessary for any items
serviced in Step 11. Check engine for oil and fuel
leaks before returning to service.
5-20-01
5-20-03 100 HOUR INSPECTION
Refer to Service Bulletin M-82-4, or current revision as applicable.
Record any values not conforming to engine specifications so that necessary repair or adjust-
ment can be accomplished.
NOTE. . . Minor changes in magneto timing can be expected during normal engine service.
The time and effort required to check and adjust the magnetos to specifications is slight and
the operator will be rewarded with longer contact point and spark plug life, smoother engine
operation and less corrective maintenance between routine inspections.
NOTE. " At each 500 hours, the magnetos should be disassembled and inspected according to
Magneto Service Manual.
10. Magneto Filter: Inspect for color, if white o.k., if red or con-
taminated, replace.
5-20-02
5-50-00 UNSCHEDULED MAINTENANCE.
Detailed information required for component, part replacement, system adjustments, accessory
replacement and repair, top overhaul, etc., can be found in "Related Publications" listed in
Chapter 1.
NOTE. .. In case of engine overspeed, refer to the current Overspeed Limitations Service
Bulletin M87-9 or current revision as applicable.
NOTE. . . In case of prop strike, refer to Service Bulletin M-84-16, or current revision as
applicable.
NOTE. . . In case of lightening strike, refer to Service Bulletin M-88-9, or current revision as
applicable.
5-50-01
INTENTIONALLY
LEFT
BLANK
5-50-02
CHAPTER 70
STANDARD PRACTICES
70-00-00 GENERAL
70-00-01
70-00-00 GENERAL
To facilitate and ensure proper reinstallation, tag and/or mark all parts and hardware as to
their location as they are removed or disassembled.
When removing any tubes or engine parts, look for indications of scoring, burning or other
undesirable conditions. Tag any unserviceable parts or units for investigation and possible
repair. Take extreme care to prevent foreign matter (Iockwire, nuts, washers, dirt, etc.) from
entering the engine whether it is on or off the aircraft. Make use of protective caps, plugs,
and covers to ensure openings are unexposed.
CAUTION. .. Dust caps used to protect open lines should always be installed OVER the tube
ends and NOT IN the tube ends. Flow through the lines may be blocked off if lines are
inadvertently installed with the dust caps in the tube ends.
If anything is dropped into the engine, work should be stopped immediately and the item
removed even if considerable time and labor is required.
Insure all parts are thoroughly clean before assembling, especially during engine build-up.
All lockwire and cotter pins must fit snugly in holes drilled in specific hardware. On
castellated nuts, the cotter pin head must fit into a recess of the nut with the other end bent
such that one leg is back over the stud and the other is down flat against the nut. Use only
corrosion resistant steel for cotter pins or lockwire.
When replacing gaskets, packings, or rubber parts, use the same type or composition as that
of the part that was removed.
Use only a plastic or rawhide mallet when installation of a part requires such force.
Loose fitting spline drives external to the engine which have no means of lubrication should
be lubricated with an anti-seize lubricant such as molybdenum disulfide.
70-00-02
70-10-00 LOCKWIRE PROCEDURE
\
6. BENDING WIRE AROUND BOLT 7. TWISTING WIRE 8. BENDING TWISTED WIRE 9. CUTTING EXCESS WIRE
70-00-03
70-20-00 PERMATEX, THREADING PROCEDURE AND GASKET MAKER
1. Use full strength non-thinned Permatex aviation grade 3D. Shake or mix well before
using.
2. Apply Permatex No. 3D to the threaded case half, only in areas where thread is shown,
using short light brush strokes until an even, thin coat is obtained. The Permatex should be
viscous enough that most of the brush marks disappear. If not, use a new can of aviation
Permatex. (Allow the Permatex to air dry to a tacky condition before threading) .
. 3. Apply a thin even coat of gasket maker between .010 and .020 of an inch thick to all
areas listed in paragraph "2" above on the non-thread crankcase half.
4. Apply grade D silk thread PIN 641543 as shown in illustration, being sure that free ends
are covered by gasket, except at oil seal.
5. Assemble crankcase halves using bolts for alignment to prevent movement of the thread
and torque all bolts in proper sequence according to Figure 72-60-020. Torquing sequence as
soon as possible.
SPACE THREAD
EVENLY BETWEEN
BOLT HOLES AND
EDGE OF CIC
FLANGE PERMATEX
SILK------
THREAD
--"---
70-00-04
70-30-00 APPLICATION OF ADHESIVES.
Adhesives and sealants will be used only in specific applications, outlined in Chapter 1
"Sealants and Lubricants".
Gasket Maker PIN 646942 - Surfaces must be clean and free of oil and grit. Apply an even
coat of Gasket Maker between .010 and .020 of an inch thick to the surface specified in
Chapter 1 "Sealants and Lubricants".
Gasket Maker is an easily workable tacky gel which can be extruded onto one side of a flange
surface from a tube and evenly spread, or small parts can be covered adequately by pressing
them into a saturated polyester urethane sponge or by roll coating them with a short nap
roller. Once Gasket Maker has been applied, evenly torque assembly into place. Excess
material can be cleaned by wiping (chlorinated solvent is helpful). Material on hands can be
cleaned with waterless mechanic's hand soap followed by soap and water.
Following visual inspection, if the gasket shows any indication of gouges, nicks, cuts or bend
and fatigue marks, immediately replace with new, pre-inspected gasket.
Gasket surfaces must be clean and free of oil and grit. Apply a thin coat of TCM Copper
Coat #642188 to both sides of gasket unless otherwise specified. (Refer to Item No. 10 in
Chapter 1 "Sealants and Lubricants" for application of Copper Coat). Once Copper Coat has
been applied, position gasket with the Copper Coat to its respective side, according to Chapter
1 "Sealants and Lubricants". Evenly torque assembly into place without stressing gasket.
GENERAL '
We have received reports of incorrect cylinder leakage check results caused by improper use
of test equipment and/or by the use of faulty test equipment.
To help you accurately accomplish a leakage check, we submit the following information on
leakage and use of the Master Orifice tool (Ref. Figure 70-50-O1) to calibrate the leakage
checking equipment used on Teledyne Continental engines. Refer to Service Bulletin M-84-15,
or current revision as applicable.
70-00-05
FACTORY CALIBRATED ORIFICE
~
Clean with soft brush. Do Not Alter Size)
c;;;;;;;;;:=== _ _nmnnmR/~CAUpST
~ ~
DUST
CAP _ ....,mlitlttlttttt
CYLINDER
HEAD &
BARREL
SPARK 1ST AND
SEAL
PLUG SEAL 2ND
WALL
COMPRESSION
DIMENSION
RING
AND CHOKE
GAP
70-00-06
70-50-01 LEAKAGE CHECKS
Cylinder leakage is broken down into two areas of concern, the "Static Seal" and the "Dynam-
ic Seal".
Static Seal
The static seal consists of the valve to valve seat seals, spark plug to spark plug port seals
and cylinder head to barrel seal (Ref. Figure 70-50-02). No leakage of the static seal is·
permissible.
Dynamic Seal
The dynamic seal consists of the piston rings to the cylinder wall seal (Ref. Figure 70-50-02).
This seal leakage can vary trom engine to engine by the cylinder displacement, cylinder choke,
ring end gap and piston design.
70-50-02 EQUIPMENT
Testing equipment must be kept clean and checked periodically for accuracy as follows:
Using a line pressure of 100 to 120 p.s.i., close the cylinder pressure valve, then set the
regulator pressure valve to 80 p.s.i. The pressure in both gages should stabilize with no
leakage.
The restrictor orifice dimension in the differential pressure tester (Figure 70-50-03) for
Teledyne Continental aircraft engines must be 0.040 inch orifice diameter, 0.250 inch long
with 60° approach angle, and must flow 120 ± cubic feet per hour at 30 p.s.i. differential
pressure.
For conformity ---in tester equipment, a Master Orifice Tool has been developed to calibrate
equipment and determine the low indicated leakage limit prior to the engine leakage check.
Connect compressed air at 100-120 p.s.i. to the tester with cylinder pressure valve closed.
Turn the regulator pressure valve on, adjusting pressure to indicate 80 p.s.i. Remove the dust
caps from both ends of the Master Orifice Tool and install onto the cylinder spark plug
adapter. Turn the cylinder pressure valve on and readjust regulator pressure gage to read 80
p.s.i. At this time, the cylinder pressure gage indication will be the low allowable limit for
cylinder leak checks. The low allowable limit is referred to as the master orifice calibrated
pressure reading. After the master orifice calibrated pressure reading has been recorded,
close regulator pressure valve and remove Master Orifice Tool from the cylinder adapter.
70-00-07
CYLINDER
ADAPTER
REGULATOR REGULATOR
PRESSURE PRESSURE
GUAGE GUAGE
REGULATOR REGULATOR
PRESSURE PRESSURE
VALVE VALVE
The following procedures are listed to outline the principles involved, and are intended to
supplement the manufacturer's instructions for the particular tester being utilized.
WARNING ••. Magnetos and fuel must be shut off prior to test to make certain that the
engine cannot accidentally fire.
(a) Perform the test as soon as possible after the engine is shut down to ensure that the
piston rings, cylinder walls, and other engine parts are well lubricated and at running
tolerance.
(b) Remove the most accessible spark plug from each cylinder.
(c) Turn the crankshaft by hand in the direction of rotation until the piston (in the cylinder
being checked) is coming up on its compression stroke.
(d) Install an adapter in the spark plug hole and connect the differential pressure tester to
the adapter. (NOTE: Cylinder pressure valve is in the Closed position). Slowly open the
cylinder pressure valve and pressurize the cylinder not to exceed 20 p.S.i.
Continue rotating the engine against this pressure until the piston reaches top dead center
(TOC). Reaching TOC is indicated by a flat spot or sudden decrease in force required to turn
the crankshaft. If the crankshaft is rotated too far, back up at lease one-half revolution and
start over again to eliminate the effect of backlash in the valve operating mechanism and to
keep the piston rings seated on the lower ring lands. This is critical because the slightest
movement breaks this piston ring sealing and allows the pressure to drop.
CAUTION . . . Care must be exercised in opening the cylinder pressure valve, since sufficient
air pressure will be built up in the cylinder to cause it to rotate the crankshaft if the piston
is not at TDC. It is recommended that the propeller be secured during check to prevent
possible rotation.
(e) Open the cylinder pressure valve completely. Check the regulator pressure gage and
adjust, if necessary, to 80 p.s.i.
70-00-08
(f) Observe the pressure indication on the cylinder pressure gage. The difference between
this pressure and the pressure shown by the regulator pressure gage is the amount of leakage
through the cylinder. If the cylinder pressure gage reading is higher than the previously
determined master orifice calibrated pressure reading, proceed to the next cylinder leak check.
If the cylinder pressure gage reading is lower, proceed with the following.
(g) The source of air leakage should first be checked for the static seal. Positive identifica-
tion of static seal leakage is possible by listening for air flow sound at the exhaust or
induction system cylinder port. When checking for cylinder head to barrel leakage, use a
soapy solution between the fins and watch for bubbles. Use a soapy solution also around both
spark plug seals for leakage. NO LEAKAGE IS ALLOWED IN STATIC SEALS.
(h) If leakage is occurring in the intake or exhaust valve areas, it may be possible to
correct a low reading by staking the valves. This is accomplished by placing a fiber drift on
the rocker arm directly over the valve stem arid tapping the drift several times with a hammer
to dislodge any foreign material that may be between the valve face and seat.
CAUTION. . . When correcting a low reading in this manner, rotate the propeller so the
piston will not be at TDC. This is necessary to prevent the valve from striking the top of
the piston in some engines. Rotate the propeller again before rechecking leakage to reset the
valves in the nonnal manner.
(i) If leakage is noted between the cylinder head and barrel, REPLACE THE CYLINDER. If
leakage cannot be corrected at the valves by "staking", the cylinder must be removed and
repaired before a Dynamic Seal Check.
NOTE. . . When the cylinder is removed, with the spark plugs installed, inspection can be
accomplished by filling the inverted cylinder bore with nonflammable solvent and then
inspected for leaks at the static seal areas.
0) If the cylinder was removed for static leakage, replacement or repair, inspect piston
ring gap and cylinder wall for tolerance (Ref. Dynamic Seal, Figure 70-50-02). Once the
piston and the cylinder have been cleaned, inspected, and ring gap tolerances have been met,
reassemble to the engine.
(k) To check the dynamic seal of a cylinder, proceed with the leakage test and observe the
pressure indication of the cylinder pressure gage. The difference between this pressure and
the pressure shown by the regulator gage is the amount of leakage at the dynamic seal.
(I) If the leakage is below the previously determined low cylinder gage reading, loss past the
dynamic seal may be due to piston ring end gap alignment or by the piston and piston rings
angular direction in the cylinder bore (Figure 70-50-04).
70-00-09
r
TOP COMPRESSION
RING GAP
T.O.C.
fA
DIRECTION
o
OF
MOVEMENT
T.O.C.
r TOP COMPRESSION
RING GAP
o
DIRECTION
OF
MOVEMENT
FIGURE 70-50-04
First assure that the piston and piston rings are centered. This may be accomplished by
reducing regulator pressure to 20 p.s.i. and working piston through TOG several times,
bringing the piston to TOG in the normal direction of engine rotation. Adjust regulated
pressure to 80 p.s.i. and determine amount of loss. If the gage reading is higher than the
previously determined master orifice calibrated reading, proceed to next cylinder to be tested.
NOTE. . . Piston ring rotation within the ring land is a normal design characteristic. As
illustrated in Figure 70-50-04, the compression ring location may have a direct bearing on the
dynamic seal pressure check. Therefore, we suggest you complete the test in the opposite
direction if readings are below prescribed limits.
(m) If recheck of cylinder pressure gage reading indication remains below allowable loss,
engine may be run-up to operating temperature and rechecked prior to cylinder being removed
and repaired. Rework of cylinders should be accomplished as outlined in this engine overhaul
manual and service bulletins.
70-00-10
FIRST CHECK CHECK FOR METHOD 1. DISCREPANCY 2. CORRECTIVE 2. CORRECTIVE
ACTION ACTION
Apply Soapy
Cylinder Head
Solution Around Bubbles Replace Cylinder
Cracks
Fins
Test Gauge
above None None
Tolerance
FIGURE 70-50-05
70-00-11
INTENTIONALLY
LEFT
BLANK
70-00-12
CHAPTER 72
ENGINE RECIPROCATING
72-00-00 GENERAL
72-00-01 Introduction
72-00-02 Crankcase
72-00-03 Crankshaft
72-00-05 Camshaft
72-00-06 Pistons
72-00-07 Lifters
72-00-08 Cylinders
72-00-01
INTENTIONALLY
LEFT
BLANK
72-00-02
72-00-00 GENERAL
The operating limits and specifications listed in this section are applicable to the TS10-360
aircraft engine. Consult Chapter 76,77, and 80 for additional operating procedures
For time between overhaul (TBO) for TS10-360 series engines, see the latest TBO
Service Bulletin (Revised Recommended Overhaul Periods For All Teledyne Continental
Aircraft Engines). Accessories supplied with engines by TCM are considered to have the
same TBO, with criteria for service and longevity outlined in current TCM TBO Service
Bulletins, unless otherwise specified.
ENGINE SPECIFICATIONS
Manufacturer........................................................................... Teledyne Continental Motors
Model ..................................................................................................................... TS10-360
Cylinders
Arrangement.. ...................... Individual cylinders in a horizontally opposed position
Compression Ratio ........................................................................................... 7.5: 1
Firing Order............................................................................................. 1-6-3-2-5-4
* Cylinder Head Temperature Maximum Allowable ...................................... .460°F
* Indicates temperature measured by Bayonet Thermocouple,
(Aeronautical Standard AS234 element or equivalent), installed
in boss in bottom of cylinder head.
Number of Cylinders ................................................................................................ 6
Numbering (Accessory toward propeller end):
Right Side Cylinders ......................................................................................... 1-3-5
Left Side Cylinders ........................................................................................... 2-4-6
Bore (Inches) ......................................................................................................4.44
Stroke (Inches) ................................................................................................... 3.88
Piston Displacement (cu. in.) ............................................................................... 360
TOTAL BASIC ENGINE WEIGHT - DRY (No oil in sump)
(Subject to product TSI0-360-A,AB 333.56
variation of ±2.5%) TSI0-360-B,BB 329.56
TSI0-360-C,CB 302.00
TSI0-360-D,DB 302.00
TSI0-360-E,EB 385.00
TSI0-360-F,FB 393.05
TSI0-360-GB 385.85
TSI0-360-H,HB 313.00
TSI0-360-JB 313.00
TSI0-360-KB 392.00
TSI0-360-LB 390.76
TSI0-360-MB 412.00
TSI0-360-SB 412.00 •
•
TSIO-360-MB 210 165
TSIO-360-SB 220 165
•
Rated Maximum Take-Off .............................................................. GB,LB,MB 2700
Rated Maximum Take-Off ........................................................................... SB 2600
Recommended Max. for Cruising (75% Power) ........................... A,AB, B, BB 2600
Recommended Max. for Cruising (75% Power) ............................ C,CB,D,DB 2500
Recommended Max. for Cruising (75% Power) ........................... E, EB, F, FB, GB,
•
........................................................................................... H, HB, JB, LB, MB, 2450
Recommended Max. for Cruising (75% Power) ................................... KB, SB 2500
Intake Manifold Pressure (In. Hg.)
Maximum Take-Off ........................................ See Performance Chart (Chapter 76)
Maximum Continuous ................................... See Performance Chart (Chapter 76)
Recommended Continuous Max. for Cruising ................... See Performance Chart
Fuel Control System ...................................... Continental Continuous Flow Injector
Unmetered Fuel Pressure (PSIG) ........................ (See Operating Limits 77-00-04)
Fuel (Min. Grade) ........................................................ Aviation Grade 100 or 100LL
72-00-04 REVISED OCT 97
WARNING ... The use of a lower octane rated Fuel can result in destruction of an
engine the first time high power is applied. This would most likely occur on takeoff.
If the aircraft is inadvertently serviced with the wrong grade of fuel, the fuel tank
must be completely drained, properly serviced, and the proper engine inspection
completed.
Oil: (First 25 hours of operation) .............. Mineral (non-detergent) Oil or Corrosion
............................................... Preventive Oil Corresponding to MIL-C-6529 Type II
Normal Service
All Temperatures ......................................................................................... 15W-50
................................................ ., .................................................................... 20W-50
Below 50° F Ambient Air (Sea Level) ......................................... SAE 30 or 10W-30
Above 30° F. Ambient Air (Sea Level) ..........................................................SAE 50
Oil Sump Capacity ...................................... See Operating Limits Section 77-00-01
Max. Oil Consumption (Lb.lBHP/Hr. Max. at Rated Power at RPM)
ALL MODELS _.
.006 LBS. X % POWER
100
Oil Pressure
Idle, Minimum, psi (All Models) ............................................................................. 10
Normal Operation, psi (TSIO 360-A,AB,B,BB,C,CB,D,DB,H,HB,JB) ............ 30 - 60
Normal Operation, psi (TSIO 360-E,EB,F,FB,GB,KB,LB,MB,SB) ................. 30 - 80 •
Oil Temperature Limits
72-00-06
72-00-03 CRANKSHAFT
The method of numbering the crankshaft journals and cheeks is illustrated in Figure 72-00-03.
Main journals, rod journals, and crankshaft cheeks are identified by letters and location
numbers.
C.c. #2
C.C. #9
C.C. #3
Counterweights are supplied in matched pairs with the bushings installed. This is necessary to
assure that their weight difference does not exceed 2 grams.
The counterweight order number designates the vibration order the counterweight is absorbing.
If a vibration occurs six times per revolution, the counterweight which has been tuned to
counteract this frequency of vibration is designated a 6th order counterweight. Similarly, if a
vibration occurs· fives times per revolution, the counteracting counterweight is designated a
5th order counterweight.
Counterweights are installed on hanger blades located on the crankshaft #2 cheek (2 counter-
weight configuration).
The crankshaft gear is heated prior to installation to obtain a shrink fit. The gear is located
by a dowel of uniform diameter.
A neoprene oil seal, which is stretched over the crankshaft flange, and a split retainer ring
are seated between the crankcase castings in the front shaft exit area, and is sealed to the
crankshaft by a helical spring inside the seal's cavity.
The "I" beam type connecting rods have split bronze piston pin bushings and two identical
precision inserts (of the same type as the main bearings), at the crankpin end. Weight
variation of rods in anyone pair is limited to 1/2 ounce in opposite bays.
72-00-07
72-00-05 CAMSHAFT
A steel alloy forging is machined on four journals, nine cam lobes and the gear mount flange
at the rear end. The lobes and journals are ground and hardened. A groove around the front
journal passes engine oil from the right crankcase cross passage to the left case passage. The
camshaft gear is attached by four unequally spaced bolts to locate its timing mark in relation
to the cam lobes. The inner teeth of the camshaft gear drive the alternator.
72-00-06 PISTONS
Pistons are aluminum alloy forgings or castings with a steel insert casted into the top ring
groove. The skirts are solid and have cylindrical relief cuts at the bottom to clear the
crankshaft counterweights. Pistons have three ring grooves above the pin hole and one ring
groove below. Compression rings are installed in the top, second and the groove below the
pin hole. A center grooved and slotted oil ring is installed in the third groove, which has six
oil drain holes to the interior. Weights are limited to 1/2 ounce in opposite bays. Piston
pins are full floating ground steel tubes with permanently pressed-in aluminum or bronze end
plugs.
72-00-07 LIFTERS
The barrel type hydraulic lifters may be removed and replaced without complete disassembly of
the engine. Construction and operation of the lifters are described in Section 72-00-11.
72-00-08 CYLINDERS
The externally finned aluminum alloy head castings are heated and valve seat inserts installed
before the head is screwed and shrunk onto an externally finned steel alloy barrel to make
the permanent head and barrel assembly. Prefinished aluminum bronze intake valve guides and
nitralloy or niresist exhaust valve guides are pressed into the cylinder assembly. Special
18mm helical coil thread inserts are installed in upper and lower spark plug holes. The
exhaust ports are on the bottom and intake ports are on the top of the head when the
cylinder is installed. Exhaust valve faces are Stellite No. 6 and stem tips are hardened.
Valve stems are solid. The intake valve guide is equipped with a valve guide seal to prevent
oil from being drawn through the valve guide and into the cylinder. Outer retainers of the
two concentric springs surrounding each valve are locked to the stems by tapered, semi-
circular keys which engage grooves around the stems. Rotocoils are installed on intake and
exhaust valves. The controlled rotating action of this type retainer helps prevent burring and
eroding of the valve and valve seat. Inner spring retainers are pressed steel. Valve rocker
covers are stamped aluminum alloy. Rocker shafts are case hardened steel. The rocker shafts
are held in place by studs in the cylinder rocker boxes. Valve rockers are steel forgings with
hardened sockets and rocker faces and pressed-in bronze bearings. They are drilled for
lubrication. Pushrods are constructed of steel tubes and pressed-in, hardened, forged steel
ball ends, which are center drilled for oil passages. The pushrod housings are beaded steel
tubes. The bead at the cylinder end retains a washer and packing ring. The bead at the
crankcase end retains a heavy spring, washer, packing ring and second washer. The cylinders
are nitrided for hardening.
72-00-08
72-00-09 GEAR TRAIN (See Figure 72-00-09)~,
A. When starting the engine, torque is transmitted from the starter (13) through the adapter
components (14 thru 22) depending on the adapter configuration. As worm wheel (16) is
turned, the spring mounted on its hub is tightened to grip the knurled drum of the shaft gear
(17). After the engine is started, the spring returns to its normal position, thus disengaging
the starter. Some starter adapters incorporate an additional housing which provides for two
additional accessory drive pads. Gears (19, 20) provide the torque for these drives. In
addition, all TSIO-360 engines incorporate a scavenge pump in the starter adapter gear. The
scavenge pump gears (21,22) are driven by the starter shaftgear (17). The scavenge pump gear
(21) is keyed to the starter shaft gear (17).
B. Torque from the crankshaft gear (1) is transmitted directly to the camshaft gear (3).
C. The camshaft gear (3) drives the magneto gears (11, 12). The alternator drive gear (23)
meshes with the inner camshaft gear and turns the alternator shaft through a rubber bushing
drive coupling. The splined end of the oil pump drive gear (9) mates with the internal spline
of the camshaft gear and transmits torque to the oil pump driven gear (10).
D. The governor drive bevel gear (6) is keyed to the camshaft (4) and meshes with and
drives the governor bevel gear (7).
E. The splined end of the fuel pump drive shaft (8) mates with the internal spline of the
governor gear.
72-00-09
TSIO-360A
lTSIO-360E, EB, KB
A. The engine oil supply is contained in the sump. The oil is drawn from the sump,
through the oil suction tube, to fill the volume being constantly displaced by the engine
driven, gear type oil pump.
B. Oil enters the lubrication system through the oil suction screen in the lower left corner
of the crankcase cover. From the oil screen cavity a cored passage leads to the suction side
of the oil pump.
C. From the pressure side of the oil pump a cored passage conducts the oil to the pressure
oil screen assembly. From the pressure oil screen a cored passage in the sump conducts the
oil to the left crankcase main oil gallery. The rear end of the right crankcase main gallery is
aligned with a passage in the crankcase cover which directs pressurized oil to the oil pressure
relief valve.
D. An oil temperature control valve located in the oil cooler adapter regulates oil tempera-
tures within specific limits.
E. A scavenge pump is incorporated in the starter adapter to return lubrication oil from the
turbocharger to the crankcase.
72-00-11
TSIO-360-A
ACCESSORY DRIVE
IDLER SHAFT BUSHING BUSHINGS
SCAVENGE
PUMP :E
w
I-
(f)
~
Z
o
~
ro
Pi"~~
f \
)
'!
ACCESSORY DRIVE
BUSHINGS
SCAVENGE PUMP
"
".
.
u
a:CO
::>
-I
_ _ _ OIL SUCTION
_ _ _ _ OIL UNDER PRESSURE
~...... _OILPUMP
o
,...
_______ BY -PASS OIL
_ .•• _ ... OIL TEMPERATURE CONTROL VALVE
-
.. '-U'.
I
r ) OIL PRESSURE
RELIEF VALVE
BYPASS TO
oo
_ _ _ _ GOVERNOR OIL
..•.•........ SCAVENGE OIL
SUMP N
.....
w
OIL COOLER ..-'-:.
a:
::>
(!)
u:
N
...
8l
IX:
W
CD
iii
fd
Q
N
.....
oo
I
N
.....
72-00-11 VALVE MECHANISM
Exhaust valves are faced with a special heat and corrosion-resistant material and the valve
stems are chromed for wear resistance. Oil fed to the hydraulic valve lifters, under pressure
from galleries, lubricates the lifter guide surfaces and fills the reservoirs inside the lifters. Oil
from the lifters flows through the pushrods to the rocker arms. Each rocker arm directs a
portion of its oil through a drilled orifice toward the respective valve stem. Oil is returned to
the crankcase through the pushrod housings, which are sealed to the cylinder head and
crankcase by rubber seals. Drain holes in the lifter guides return oil to the sump.
The barrel type hydraulic lifter (See Figure 72-00-11) consists of a steel body (1), an expand-
ing spring (2), and a check valve assembly (3, 4, and 5), a plunger (6), a socket (7), for
pushrod end, and a retaining ring (8). A groove (9), around outside of body picks up oil from
crankcase supply hole. From the exterior groove, oil is directed to interior body groove (11)
through hole (10) and from the interior groove through the hole to the reservoir (12). Oil is
withheld from reservoir (15) by check valve ball (5) which is supported by a spring (4) and
retainer (3). The check valve is opened by outward motion of a plunger under pressure of the
expanding spring whenever a clearance occurs in the valve train. Thus, the body reservoir is
kept full of oil which transmits lifting force from the body of the plunger. The plunger and
socket are selectively fitted to the body to permit a calibrated leakage so the lifter will
readjust its effective length after each cycle, while cylinder valve is closed, to return "lash"
in valve train to zero.
The air induction system used on the TSI0-360 Series Engines consists of intake tubes,
connecting hoses, clamp assemblies, air throttle, fuel metering assembly, air reference lines,
and turbocharger. The air throttle assembly is usually located on the top center area of the
engine supported by the engine backbone. The system is provided with a drain valve at the
intake portion of the cylinder to remove any fuel that may collect there.
2
1. Body
2. Spring, plunger
3. Check ball retainer
4. Spring, check ball
5. Check ball
3 6. Plunger
7. Socket
8. Ring, retaining
9. Oil groove, exterior
10. Oil inlet, body
11. Oil groove, interior
12. Oil reservoir, plunger
13. Hole, oil discharge
14. Oil reservoir, body
15. Hole, oil outlet
FIGURE 72-00-11
72-00-13
The throttle assembly is connected to the elbows at the front cylinder intake tubes by
connector hoses and clamps. This assembly is then connected to the center intake tubes
and the center to the front intake tubes in the same manner. Each intake tube is attached
to the cylinder by a flange, sealed by a gasket and secured by two washers and two nuts.
72·00-13 EXHAUST SYSTEM
Exhaust systems for TSIO-360 A, AB, B, BB, C, CB, D, DB, H, HB, & JB are supplied by
the aircraft manufacturer. The exhaust systems that will be discussed in this manual are
I those for the TSIO-360 E, EB, F, FB, GB, KB, LB, MB, SB, LffSIO E, EB, & KB which are
supplied by Teledyne Continental Motors. The exhaust system consists of an exhaust
collector, two elbow risers, four tee risers, various tubes, couplings, turbocharger
mounting flange, fixed wastegate or wastegate and actuator. The collector assembly
routes exhaust flow to the turbocharger turbine which drives the compressor section for
compressed intake air. Turbine RPM is determined by the amount of incoming exhaust
flow which is adjusted by fixed wastegate or wastegate and actuator. On hydraulic
wastegate systems, the actuator is controlled by the variable pressure controller. Oil
pressure for the turbocharger system is engine supplied.
72-00- 14 IGNITION SYSTEM
A. Torque from the engine crankshaft is transmitted through the camshaft gear to the
magneto drive gears, which in turn drives the magneto drive coupling. The magneto
coupling incorporates an impulse coupling. As the rubber bushings in the drive gear
turns the coupling drive lugs, counterweighted latch pawls inside the coupling cover,
engage pins on the magneto case and hold back the latch plate until forced inward by
the coupling cover. When the latch plate is released, the coupling spring spins the
magnet shaft through its neutral position and the breaker opens to produce a high
voltage surge in the secondary coil. The spring action permits the latch plate, magnet
and breaker to be delayed through a lag angle of 30 degrees of drive gear rotation
during the engine cranking period. Two stop pins on the case and two lobes on the
breaker cam produce two sparks per revolution of the drive shaft. After engine is
started, counterweights hold the latch pawls clear of the stop pins and the magnet
shaft is driven at full advance.
B. Engine firing order for the TSIO-360 Series is 1-6-3-2-5-4. The firing order for the
LrrSIO-360 is 1-4-5-2-3-6. See Figure 72-00-14A. Notice the position of the No.1
cable terminal in the magneto outlet plate in relation to the magneto case. As viewed
from the distributor end, the magneto rotor turns counterclockwise, passing in
succession the terminals of spark plug cables in engine firing order. Cables are
connected to the magnetos so that the right magneto fires the upper plugs on the right
side and lower plugs on the left. The left magneto fires the upper plugs on the left and
the lower plugs on the right. The magneto cases, spark plugs, cables and connections
•
are shielded to prevent radio interference. Pressurized magnetos are installed on the
TSIO-360 FB (9), GB (4), LB MB and SB Models. See Figure 72-00-14B .
Pressurization is supplied through bleed air supplied from the pressurized induction
system.
WARNING ... Engine kickback while cranking may cause damage to the starter
adapter clutch and is an indication of malfunctioning retard system (impulse
couplings or retard breaker not functioning properly).
L----------------+----05
60~------------------------~
LOWER SPARX PLUGS
3 1) Magneto
2) T-fitting
3) Hose
4) Harness
5) Clamps
5~--------------~~
72-00-15
INTENTIONALLY
LEFT
BLANK
72-00-16
SECTION 72-10-01
DISASSEMBLY
72-10-00 DISASSEMBLY
72-10-01 General
72-10-15 Crankcase
72-10-01
INTENTIONALLY
LEFT
BLANK
72-10-02
72-10-01 GENERAL
Instructions in this section are based on the assumption that all parts attached by the aircraft
manufacturer, except optional pumps have been removed.
Properly identify each part by marking or tagging as it is disconnected from the engine, to
aid in reinstallation.
NOTE... If the engine is being removed to be placed in storage, accomplish steps listed in
Section 72-80-00, Engine Preservation.
2. Drain the engine oil from the sump. Replace drain plug and tighten.
5. Tag and disconnect the engine wiring bundle from the following components.
a. Magnetos
b. Alternator
c. Tach Generator
d. Oil Temperature Bulb
e. Cylinder Head Temperature Bulb
f. EGT Thermocouple Probe(s)
g. Remove all clamps attaching engine wire bundle to engine components and route
clear of the engine.
6. Disconnect propeller, throttle, and mixture control cables.
Attach a hoist to engine lifting eye and relieve the weight from the engine mounts.
CAUTION. .. Place a suitable stand under the aircraft tail section load bearing area (jack pad
or Ale tie down eye) before removing the engine. The loss of weight may cause the tail to
drop.
72-10-03
11. Remove the engine mounts.
12. Hoist engine vertically out of the nacelle and clear of the aircraft.
NOTE. . . Hoist engine slowly making sure that all wires, lines and hoses have been discon-
nected.
13. Install engine on a transportation stand, dolly or on the engine shipping container base.
72-10-02 EXTENT OF DISASSEMBLY. Line drawings reproduced in this section are similar to those
used in the parts catalog. The location of components and attaching parts in the illustration
will be sufficient to enable personnel to accomplish disassembly operations.
72-10-03 PARTS TO BE DISCARDED. Discard all shake proof washers, lockwires, tab washers, rubber
seal rings, oil seals, gaskets, cotter pins, flex hoses, hose connectors and magneto coupling
(rubber) bushings in such a manner that they will not be used again inadvertently. Care
should be taken in removing gaskets from aluminum parts by scraping. Such removal should
be delayed until the part is to be cleaned. (See TCM Service Bulletin 87-11R2, or current
revision applicable,) "100% Replacement Parts."
72-10-04 PRELIMINARY CLEANING. Spray or brush with a solvent used for general cleaning of engine
parts. Remove caked dirt on bolt heads and nuts especially. At the same time the oil sump
drain plugs should be removed to drain any remaining oil.
CAUTION. . . Do not use a caustic or even mild alkaline cleaning solution for external
precleaning, as these solutions will also remove the "anodized" finish of aluminum parts.
A. Disconnect cables from spark plugs (1). Remove attaching parts (2, 3) and cable outlet
plate (26) from each magneto (7).
B. Remove distributor block (24) and cable outlet plate (26) from ignition cables.
C. Remove clamps (18 thru 21) by removing attaching parts (16, 17).
E. Remove attaching parts (4, 5, 6), magnetos (7) and gaskets (8).
F. On models utilizing magneto pressurization, remove clamps (5), hose (3), tee (2), filter
(6) and hose (3), Figure 72-o0-14B.
72-10-04
~-15
~-14
~-13
~-1
23
24 25
26
3 2
27
72-10-05
72-10-06A FUEL INJECTION SYSTEM ALL MODELS EXCEPT MB (See Figure 72-10-06A)
A. Disconnect fuel discharge tubes (29) from nozzles (30), and, fuel manifold (28). Remove
nozzles. Sleeve (31),(Figure 72-10-08A) must be removed before nozzles can be removed.
B. Hoses and tube assemblies, routed to or from cylinders, fuel valve manifold assembly,
throttle control assy. air throttle adapter, or fuel nozzles, should be identified as to their
fitting-to-fitting location and temporarily marked for ease of reassembly.
C. Remove two sets of attaching parts and lift off fuel manifold valve and mounting bracket
as one unit. Any further disassembly will disturb the calibration and should be accomplished
only in accordance with the Fuel Injection Manual, Form X30593A.
D. Remove four sets of attaching parts (35, 36, 37) and remove fuel pump (2) and gasket
(1 ).
NOTE. . . Further disassembly of the fuel injection system components is not advised unless
proper test equipment is available.
NOTE. . . For further information, refer to Teledyne Continental Fuel Injection Systems
Overhaul Manual and Parts Catalog, Form X30593A.
72-10-06
,
, 19I
14 ~
...........- - , < /
1
)
28 41~
I
,,________ .............. ..jl
72-10-07
72·10-068 FUEL INJECTION SYSTEM
4, ~5
)if~3
19
A. Remove oil filter (14) attaching hardware (8, 9, 10) and oil filter adapter (11, 12, 13).
Remove and discard gasket (17), a-ring (16). On old style accessory case remove attaching
hardware (49 thru 54), brackets (59, 50) and oil filter adapter (58) or remove oil screen
assembly (45 thru 48). Discard all used gaskets and O-rings.
C. Remove attaching hardware (1 thru 6) and carefully separate accessory case from crank-
case studs. Remove and discard gasket (7).
D. Remove attaching hardware (23, 24, 25), cover (26) or tach drive assembly (42 thru 44) as
applicable. Remove nut (37), and discard gasket (27). For oil pump disassembly see Figure 72-
10-13.
E. Remove relief valve assembly items (28 thru 36). Discard gaskets (29,34).
F. Remove screen (18), plugs (20, 21) and discard gaskets (19, 22).
NOTE. . . Refer to parts manual X30597A for correct adapter to engine application, oil filter
adapter to engine. Angle orientation may vary according to engine model.
12-10-10
6
~
44~
tfi;43
~32
~1
30
36
14
72-10-11
72-10-0SA INDUCTION SYSTEM.
TSI0-360-A,AB,B,BB,H,HB,JB (See Figure 72-10-0SA).
A. Fuel nozzles should have been removed during fuel injection system disassembly.
Remove air reference lines (28) and sleeves (31) together. Disassemble air reference lines (28)
and sleeve assemblies (31) discarding used seals (32,19) and washers (33, 34).
B. Remove air reference tubes (16, 18, 29) from air throttle adapter (21) and fuel pump.
Remove fittings (26, 27) from air throttle adapter.
C. Remove attaching hardware (22 thru 25), and separate adapter (21) from air throttle
body (13). Remove and disCard gasket (20).
D. Loosen hose clamps (10, 11). Remove hoses (12) and clamps (10, 11).
E. Remove attaching hardware (7, 8, 9). Lift off induction riser assemblies (2 thru 6).
Remove and discard gaskets (1).
F. Remove hose (36), elbow or fittings (35) as applicable, attaching hardware (14, 15), and
air throttle and metering assembly (13).
72-10-12
FIGURE 72-1()"OSA. INDUCTION SYSTEM, TSIO A,AB,B,BB,H,HB,JB.
72-1()..13
72-10-08B INDUCTION SYSTEM.
TSIO 360 C,CB,D,DB (See Figure 72-10-08B).
A. Fuel nozzles should have been removed during fuel injection system disassembly.
Remove air reference lines (25, 26» and sleeves (31) together. Disassemble air reference
lines (25, 26) and sleeve assemblies (31) discarding used seals (32) and washers (33, 34).
B. Remove attaching hardware (35, 36, 37), bracket (23) and air reference tubes (27,29).
c. Remove attaching hardware (19 thru 22) and separate adapter (18) from throttle and
metering assembly (14). Remove and discard gasket (17).
D. Loosen hose clamps (10,11). Remove hoses (12,13) and clamps (10,11).
E. Remove attaching hardware (7, 8, 9) and lift off induction riser assemblies (1 thru 6).
Remove and discard gaskets (1).
F. Remove hose (39), elbow or fittings (38) as applicable, attaching hardware (15, 16, 20),
and air throttle and metering assembly (14).
72-10-14
FIGURE 72-10-08B. INDUCTION SYSTEM, TSIO~360-C,CB,D,DB.
72-10-15
72-10-08C INDUCTION SYSTEM.
TSI0-360-E,EB,F,FB,LTSI0-360-E,EB (See Figure 72-10-08C).
A. Fuel nozzles should have been removed during fuel injection system disassembly.
Remove air reference lines (20) and sleeves (21) together. Disassemble air reference lines (20)
and sleeve assembles (21) discarding used seals (22) and washers (23, 24).
B. Remove air reference tubes (16, 18) and fittings (39) from air throttle adapter (36).
C. Loosen clamps (25), remove hoses (26), clamps (25) and induction tubes (27, 28).
Remove attaching bolts (31), and overboost valve (30). Remove and discard O-ring (29).
D. Remove attaching hardware (8, 9, 37, 38). Separate adapter (36) from throttle and
metering assembly (13). Remove and discard gasket (40).
E. Loosen clamps (10, 11), remove hoses (12), clamps (10, 11) attaching hardware (7, 8, 9)
and lift off induction riser assemblies (1 thru 6). Remove and discard gaskets (1).
F. Remove hose (35), elbow or fittings (34, 39) as applicable, attaching hardware (14, 15) ,
and air throttle and metering assembly (13).
72-10-16
27
26
~)
\31
~t)
25
~~, I
26
72-10-17
72-10-080 INDUCTION SYSTEM.
TSI0-360-GB,LB (See Figure 72-10-080).
A. Fuel nozzles should have been removed during fuel injection system disassembly.
Remove air reference lines (20) and sleeves (21) together. Disassemble air reference lines (20)
and sleeve assemblies (21) discarding used seals (22) and gaskets (23, 24).
B. Remove air reference tubes (16, 18) and fittings (39) from air throttle adapter (36).
C. Loosen clamps (25) and remove hoses (26), clamps (25) and induction tubes (27, 28).
Remove attaching bolts (31) and overboost valve (30). Remove and discard o-ring (29).
D. Remove attaching hardware (8, 9, 37, 38) and separate adapter (36) from throttle and
metering assembly (13). Remove and discard gasket (40).
E. Loosen clamps (10, 11), remove hoses (12), clamps (10, 11), attaching hardware (7, 8, 9)
and lift off induction riser assemblies (1 thru 6). Remove and discard gaskets (1).
F. Remove hose (35), elbow or fittings (34) as applicable, attaching hardware (14, 15), and
air throttle and metering assembly (13).
72-10-18
25
ji
~~ I
26t)
72-10-19
72-10-0SE INDUCTION SYSTEM.
TSIO/LTSI0-360-KB (See Figure 72-10-0SE).
A. Fuel nozzles should have been removed during fuel injection system disassembly.
Remove air reference lines (20) and sleeves (21) together. Disassemble air reference lines (20)
and sleeve assemblies (21) discarding used seals (22) and gaskets (23, 24). '
B. Remove air reference tubes (16, 18) and fittings (39) from air throttle adapter (36).
c. Loosen clamps (25), remove hoses (26), clamps (25) and induction tubes (27, 28).
Remove attaching bolts (31) and overboost valve (30). Remove and discard o-ring (29).
D. Remove attaching hardware (37, 38). Separate adapter (36) from throttle and metering
assembly (13). Remove and discard gasket (40).
E. Loosen clamps (10, 11). Remove hoses (12), clamps (10, 11), attaching hardware (7, 8, 9),
and lift off induction riser assemblies (1 thru 6). Remove and discard gaskets (1).
F. Remove hose (35), elbow or fittings (34) as applicable, attaching hardware (14, 15) and
air throttle and metering assembly (13).
72-10-20
4
10 , 24
.
'"-"
r:>-< 23
5/ I .
,
"
72-10-21
72-10-0SF INDUCTION SYSTEM.
A. Plug (1) and gasket (2) should have been removed at the beginning of engine disassembly
to drain the engine's oil supply. If not, remove plug (1) and gasket (2).
B. Remove attaching hardware (3, 4, 5) and oil sump (8). Remove and discard gasket (7).
72-10-24
72·10-10 OIL COOLER (See Figure 72-10-10).
Refer to Service Bulletin M-76-5R1, or current revision as applicable.
A. Remove attaching hardware (4, 5, 6), oil cooler (7). Remove and discard gasket (8).
B. Remove shoe (3), bolt (2), and nut (1) from rocker cover.
C. Remove attaching hardware (9, 10) and engine mount adapter (11) from crankcase studs.
Remove and discard o-rings (12, 13).
D. Remove plug (16), gasket (17), oil temperature control valve (15) and gasket (14) from
engine mount, adapter (11).
16 -iW
17-~
15
72·10-25
72-10-11 ALTERNATOR ASSEMBLY (See Figure 72~10-11).
A. Remove attaching hardware (15, 16) and pull alternator (2) from accessory case studs.
C. Remove cotter pin (14), nut (13), gear (10), sleeve (7), bushings (9), retainer (8), hub (6),
oil seal (5), o-ring (4) and woodruff key (3) from alternator (2).
15 16
I~~
I
12
~. 5
1. Gasket 9. Bushing
2. Alternator 10. Gear
3. Woodruff key 11. Coupler
4. O-ring 12. Sleeve
5. Oil seal 13. Nut, castellated
6. Hub 14. Pin, cotter
7. Sleeve 15. Washer, plain
8. Retainer 16. Nut, elastic stop
72-10-26
INTENTIONALLY
LEFT
BLANK
72-10-27
72-10-12A STARTER AND STARTER ADAPTER.
TSI0-360-A,AB,D,DB. OPTIONAL ON TSI0-360 LB (See Figure 72-10-12A).
Refer to Service Bulletin M-74-17, or current revision as applicable.
A. Remove attaching hardware (57, 58) and pull starter (56) from adapter (2) studs. Remove
and discard o-ring (55).
B. Remove retaining ring (13) using snap ring pliers. With proper size drift and soft mallet,
tap needle bearing (7) driving bearing (12) worm shaft (8), spring (9), wormgear (11), and
needle bearing (7) out of starter adapter (2).
C. Remove attaching hardware (34, 35, 36, 60 thru 63) and accessory drive adapter (22).
Remove screw (38), washer (37), bushing (31), gear (30), and gear (32). Remove and discard
o-ring (21). Remove attaching hardware, covers and gaskets (45 thru 54). Using snap ring
pliers, disengage retaining ring (44) and slide it back on shaft (43). Press shaft (43) thru left
accessory drive pad opening. As shaft is pressed out, retaining ring (44) and gear (41) will
fall free inside accessory drive adapter for removal. Key (42) should be removed with shaft
(43).
D. Remove oil seals (26, 27). Bushings (24, 23) can be removed using an arbor press.
Remove gear (40) and bushing (25).
E. Remove attaching hardware (59, 64) and separate starter adapter housing (2) from
accessory case. Remove and discard gasket (1).
F. Install starter adapter housing (2) in a shielded vise. Slide bearing (39) off shaftgear
(19). Remove worm wheel gear (15), bearing (14), spring (16), and shaftgear (19) by turning
worm wheel gear (15) counterclockwise and pulling outward simultaneously to release spring
(16).
G. Install worm wheel gear (15) in shielded vise, bend back tab on tab washer (17) and
remove screw (18) and tab washer (17). Turn flat spot on spring which was being held by
screw (18) 1800 on worm wheel gear until it lines up with opposite hole. USing a small
screwdriver through hole, pry spring outward until it is disengaged from worm wheel gear
(15). Separate worm wheel gear (15), roller bearing (14), spring (16) and shaftgear (19).
72-10-28
FIGURE 72-10-12A. STARTER AND STARTER ADAPTER TSIO·360-A,AB,D,DB. OPTIONAL ON LB.
72-10-29
72-10-12B STARTER AND STARTER ADAPTER,
TSI0-360-B,BB,C,CB,H,HB & JB (See Figure 72-10-12B).
A. Remove attaching hardware (43. 44. 49) and pull starter (42) from adapter (2) studs.
Remove and discard o-ring (41).
B. Remove retaining ring (13) using snap ring pliers. With proper size drift and soft mallet.
tap needle bearing (7) driving bearing (12), worm shaft (8). spring (9), worm gear (11). and
needle bearing (7) out of starter adapter (2).
C. Remove attaching hardware (38. 39, 40). cover (37). and oil seal (23) from scavenge pump
housing (21). Remove attaching hardware (29, 30, 31). (46, 47, 48. 49) and scavenge pump
housing (21) from starter adapter (2). Remove and discard o-ring (20). To disassemble
scavenge pump. remove screw (33). washer (32), cover (28). gears (25, 27), bushings (22. 26)
and woodruff key (35) from scavenge pump housing (21). Remove and discard o-ring (20).
D. Remove attaching hardware (45. 50) and separate starter adapter (2) from accessory case.
Remove and discard gasket (1).
E. Install starter adapter housing (2) in a shielded vise. Slide bushing (34) off shaftgear
(19). Remove worm wheel gear (15). bearing (14). spring (16). and shaftgear (19) by turning
worm wheel gear (15) counterclockwise and pulling outward simultaneously to release spring
(16).
F. Install worm wheel gear (15) in shielded vise. bend back tab on tab washer (17). and
remove screw (18) and tab washer (17). Turn flat spot on spring. which was being held by
screw (18). 180° on worm wheel gear until it lines up with opposite hole. Using a small
screwdriver through hole. pry spring outward until it is disengaged from worm wheel gear
(15). Separate worm wheel gear (15). roller bearing (14). spring (16). and shaftgear (19).
72-10-30
9
28
27 20
<: ,~
',-",'
21
48~
49 ~
72-10-31
72-10-12C STARTER AND STARTER ADAPTER,
I TSIO-360-E, EB, F, FB, GB, KB, MB & SB and L/TSIO-360-E, EB, KB (See Figure 72·
10-12C).
A. Remove attaching hardware (47, 48) and pull starter (46) from adapter (2) studs.
Remove and discard o-ring (45).
B. Remove retaining ring (15) using snap ring pliers. With proper size drift and soft
mallet, tap needle bearing (7), driving bearing (11), worm shaft (8), spring (9), worm
gear (12) and needle bearing (7) out of starter adapter (2).
C. Remove attaching hardware (42,43,44), cover (41) and oil seal (25) from scavenge
pump housing (23). Remove attaching hardware (34, 35, 36), (50 thru 53), bracket
(55) on TSIO-360 MB, and scavenge pump housing (23) from starter adapter (2).
Remove and discard o-ring (22). To disassemble scavenge pump, remove screw
(38), washer (37), cover t32), gears (29, 31), bushings (24, 30), and woodruff key (39)
from scavenge pump housing (23). Remove fittings (27, 28). Remove and discard 0-
ring (22).
D. Remove attaching hardware (49, 52) and separate starter adapter (2) from accessory
case. Remove and discard gasket (1).
E. Install starter adapter housing (2) in a shielded vise, slide bushing (33) off shaftgear
(21), remove worm wheel gear (17), bearing (16), spring (18), and shaftgear (21) by
turning worm wheel gear (17) counter clockwise and pulling outward simultaneously to
release spring (18). On LfTSIO models, worm wheel gear (17) must be turned
clockwise while pulling outward to release spring (18).
F. Install worm wheel gear (17) in shielded vise, bend back tab on tab washer (19), and
remove screw (20), tab washer (19). Turn flat spot on spring, which was being held by
screw (20), 180 0 on worm wheel gear until it lines up with opposite hole. Using a small
screwdriver through hole, pry spring outward until it is disengaged from worm wheel
gear (17). Separate worm wheel gear (17), roller bearing (16), spring (18), and
shaftgear (21 ).
A. Remove nut (10), slide oil pump drive gear (7) out of gear (4) and oil pump cover (6).
B. Bend back ears on tab washers (8), loosen bolts (9), and remove. Remove oil pump cover
(6).
C. Lift drive gear (4) and driven gear (5) out of accessory case oil pump cavity.
D. Mount accessory case in proper fixture. Using arbor press, remove bushing (2). If worn
beyond serviceable limits, bushing (3) may be removed from gear (5).
72-10-34
1
E$."
I '
10
72-10-35
INTENTIONALLY
LEFT
BLANK
72-10-36
72·1 0-14A INTERCYLINDER AIR BAFFLES,
TSIO/LTSIO-360 E, EB, KB & TSIO-360 F, FB, GB, LB MB & SB. I
A. Remove four bolts (6), four washers (16), fuel line support brackets (1, 7) and spacers
(2). Fuel line clamps (17) need not be removed from support bracket unless
damaged.
B. Remove screws (4) and washers (16) and lift off support (5).
C. Push in baffle fasteners (10) to compress spring (11 ) and disengage fastener from
supports (3). Remove baffles (8, 9, 12, 13, 14, 15). Remove supports (3) from
between cylinder fins.
72-10-38
72-10-14B CYLINDER AND PISTON ASSEMBLY
A. With engine in the inverted position, remove attaching parts (1, 2, 3), covers (4, 5) and
gaskets (7). Position crankshaft so valve lifters of cylinder to be removed are on heels of
cam lobes and both valves are fully closed. Bend down ears of tab washers (9) clear of nuts
(8). Remove nuts and washers (8, 9), rocker retainer (10), shafts (11), thrustwasher (12),
bushing (13), and rocker assemblies (14, 15). Withdraw pushrods (16). Repeat these steps on
the remaining cylinders.
B. Push the pushrod housings (21) in towards the crankcase until the cylinder flange end is
clear. Lift the cylinder end of the housing and withdraw from the crankcase. Disconnect and
remove drain tube assembly (22). Remove and discard seals (23). Disconnect spring (50) and
remove with baffle (49).
C. Rotate engine to upright position. Insure that piston in cylinder to be removed is in top
dead center position. Remove flange nuts (24, 25). Cradle cylinder (48) in either arm and
withdraw it straight outward, catching piston with free hand as it clears cylinder to prevent
damage to crankcase.
D. Remove piston pin (26), piston (31), and rings (27 thru 30) immediately after removing
cylinder (48). Remove hydraulic lifters (41) from crankcase. TCM recommends 100% replace-
ment of hydraulic lifters at engine overhaul regardless of condition.
E. Remove and discard cylinder base packing (32). Use of a cylindrical wood block and a
lever type valve spring compressor is recommended to facilitate removal of valve springs (35,
36) and to prevent valves (38, 39) from dropping.
F. Compress valve springs (35, 36) and remove keys (33). Use caution to prevent cocking of
keys (33) or roto coils (34) and scoring valve stems. Remove roto coils (34), springs (35, 36)
and inner retainers (37). Hold the valve stems while lifting the cylinder from its support.
Lay the cylinder on its side and stone any nicks on the valve stems before removing valves
(38,39).
G. Remove piston rings (27 thru 30) from piston (3l) using caution to prevent scoring of
piston lands with ring ends.
NOTE. . . As pistons and cylinders are being removed, the piston to cylinder position should
be checked and recorded to insure that piston is placed back in cylinder in same position at
engine assembly. Pistons have a raised part number on one side of the piston pin boss. This
number can be recorded as either fwd or aft as applicable. Example; cylinder no. 4, piston
PIN aft.
72-10-39
72-10-15 CRANKCASE (See Figure 72-10-15).
A. If not already accomplished, remove oil gauge rod and o-ring (1, 2). Remove attaching
hardware (3, 4, 5), clamp (6), oil gauge housing (9), and bracket (7). Remove attaching
hardware (10, 11, 12), and oil cooler (13). Remove and discard gasket (14). Loosen and
remove plug (16) and oil temperature control valve (17). Discard gasket (15).
B. Rotate engine stand to place 2-4-6 (left) side of crankcase downward. Place a suitable
support of proper length (wood or pipe using a soft shield to prevent damage to crankcase)
under 2-4-6 (left) side of crankcase to help support during assembly.
C. On current model engines, remove attaching hardware (61, 62, 63), 1-3-5 side engine
mounts (64, 65), attaching hardware (95 thru 98) and turbocharger mounting bracket (93) as
applicable. Remove and discard o-rings (75). On older model TSIO, LTSI0-360-E,F engines,
remove attaching hardware (61, 62, 63), 1-3-5 side engine mount spacers (92) and turbocharger
mounting bracket (94) as applicable. Remove and discard o-rings (75). O-rings (75) are used
on both sides of spacers (92, 93) and bracket (94) as applicable.
D. Remove attaching hardware (18 thru 23), bracket (24) or brackets (89, 90), attaching
hardware (25 thru 29) and lifting eye (30). Remove attaching hardware (31 thru 42).
E. Remove attaching parts (43, 44) from both ends of thru bolts (45) and from the right
crankcase side of thru bolts (46). Remove attaching hardware (47, 48, 49) from both ends of
thru bolts (50, 51). Remove attaching parts (53, 54, 55) from both ends of thru bolt (56).
Remove attaching hardware (57, 58) from both ends of thru bolts (59, 60). Very carefully,
using a brass or fibre drift, drive all thru bolts except thru bolt (59) downward and out of 2-
4-6 side of crankcase. Thru bolt (59) must be extracted from the 1-3-5 side of crankcase to
prevent damage to adapter (67). Catch each thru bolt as it leaves the case to prevent damage
to threads. Discard o-rings.
F. Stand numbers (1, 3, and 5) connecting rods upright and lift off the right 1-3-5 crank-
case half. Lift out camshaft assembly, fuel pump drive shaft and governor drive gear.
Remove crankshaft assembly with connecting rods, thrust washers and main bearings. Remove
left crankcase from stand.
G. Remove attaching hardware (47, 48, 49) and remove engine mounts (66, 67). Remove and
discard o-rings (75, 74). On older model TSIO, LTSI0-360-E,F engines, remove spacers (91,
92) and discard o-rings (74, 75) used on both sides of spacers.
72-10-40
FIGURE 72-10-15. CRANKCASE
1. Oil gauge rod 21. Washer 42. Bolt 64. Right rear 82. Right
2. "O"-ring 22. Washer 43. Nut mount bracket crankcase
3. Screw 23. Bolt 44. Washer 65. Right front 83. Left crankcase
4. Locknut 24. Air throttle 45. Thru bolt mount bracket 84. Spacer
5. Washer bracket 46. Thru bolt 66. Left front 85. Squirt nozzle
6. Clamp 25. Nut 47. Nut mount bracket 86. Shoe
7. Bracket 26. Lockwasher 48. Lockwasher 67. Left rear 87. Bolt
8. Circlip 27. Spacer 49. Washer mount bracket 88. Nut
9. Oil gauge housing 28. Washer 50. Thru bolt 68. Bolt 89. Bracket,
10. Screw 29. Bolt 51. Thru bolt 69. Lockwasher air throttle
11. Lockwasher 30. Lifting eye 52. Thru bolt 70. Washer 90. Bracket,
12. Washer 31. Nut 53. Nut 71. Spacer adapter
13. . Oil cooler 32. Lockwasher 54. Lockwasher 72. Cover 91. Spacer
14. Gasket 33. Washer 55. Washer 73. Gasket 92. Spacer
15. Gasket 34. Bolt 56. Thru bolt 74. "O"-ring 93. Bracket, turbo
16. Plug, machine 35. Nut 57. Flanged nut 75. "O"-ring 94. Clamp
thread 36. Lockwasher 58. Washer 76. Bushing 95. Bolt
17. Temperature 37. Washer 59. Thru bolt 77. Helical coil 96. Washer
control valve 38. Bolt 60. Thru bolt 78. Dowel 97. Nut
18. Nut 39. Nut 61. Nut 79. Drive screw 98. "Oil-rings
19. Lockwasher 40. Lockwasher 62. Lockwasher 80. Nameplate
20. Washer 41. Washer 63. Washer 81. Breather
72-10-41
72-10-16 CAMSHAFT ASSEMBLY (See Figure 72-10-16).
B. Remove governor driven gear (1) and fuel pump drive shaft (2) from crankcase.
A. Use wooden support blocks under front and rear main journals during disassembly of
crankshaft.
B. Remove cotter pin (7), castellated nuts (8), bolts (9), and separate connecting rod caps
(10) and rods (13). Remove connecting rod bearings (11). Loosely reassemble rods, caps,
bolts, and nuts with their position numbers matched.
C. Remove retaining rings (14), retaining plates (15), and pins (16). Remove counterweight
assemblies (18).
WARNING ••• Do not mark crankshaft using any metal object such as a drift punch, scribe,
etc.
D. Cut lockwire, remove six bolts (20), and pull gear (21) from crankshaft (24).
E. Work oil seal spring (5) from its groove. Remove oil seal (6) and spring (5) from
crankshaft.
72-10-42
12
22
72-10-43
72-10-18A EXHAUST SYSTEM REMOVAL AND DISASSEMBLY,
LjTSI0-360-E,EB & KB (See Figure 72-10-18A).
A. Remove turbo to scavenge pump hose assembly (37), check valve (36), bracket (35),
attaching hardware (32, 33), clamp (34) and tube assembly (30). Remove elbow (29) and
reducer (28).
B. Remove attaching hardware (43), clamp (42) and crankcase to turbo hose assembly (44).
Remove check valve (41), elbow (40) and tee (39).
c. Remove attaching hardware (21 thru 26), support bracket (20), wastegate (13), clamps (19)
and turbocharger (18).
D. Place engine in inverted position. Remove attaching hardware (2), exhaust risers (3 thru
8) elbows (9, 10) and manifold (11). Remove and discard gaskets (1).
72-10-44
FIGURE 72-10-18A. EXHAUST ASSEMBLY TSIO/LTSI0-360-E,EB & KB
72-10-45
72-10-18B EXHAUST SYSTEM REMOVAL AND DISASSEMBLY,
TSI0-360-F,FB (See Figure 72-10-18B).
A. Remove turbo to scavenge pump hose assembly (27), attaching hardware (22, 23, 24),
clamp (25), check valve (26), tube (21), elbow (20) and reducer (19).
B. Remove attaching hardware (33), clamp (32), hose (34), nipple (29), plug (30), tee (31),
and fitting (28).
C. Remove wastegate (11), clamps (18), tailpipe assembly (10), turbocharger (17), attaching
hardware (12, 13, 15, 16), manifold (9) and elbow (8).
D. Remove attaching hardware (14) and riser assemblies (2 thru 7) from engine.
72-10-46
~27
'\j
11
72-10-47
72-10-18C EXHAUST SYSTEM REMOVAL AND DISASSEMBLY,
TSIO-360-GB & LB (See Figure 72-10-18C).
A. Remove clamp (1), tailpipe (2) and wastegate (3). Remove hose (6), elbow (7), fitting (8),
attaching hardware (32, 33, 34), clamp (35) check valve (5) and hose (4).
B. Remove hose (11), elbows (12, 15), tee (13), fitting (14), attaching hardware (36, 37, 38),
clamp (39), check valve (10) and hose assembly (9).
c. Remove turbocharger to bracket clamp (16), turbocharger (17), attaching hardware (18),
riser assemblies (19, 21, 24, 25, 26), attaching hardware (29, 30), bracket (31), riser (22) and
elbow (23).
72-10-48
~~-
17 /'~~19
16 ~r!f-'-
15 18
72-10-49
I FIGURE 72-10-180. EXHAUST SYSTEM TSIO-360-MB & SB
1. Turbo inlet manifold 18. Turbocharger 37. Bolt 55. Washer, lock
2. Riser 19. Bracket 38. Nut 56. Screw
3. Riser, elbow 20. Hose 39. Bracket 57. Washer, lock
4. Riser, tee 21. Hose 40. Clamp 58. Screw
5. Riser, tee 22. Hose 41. Bolt 59. Gasket
6. Riser, elbow 23. Elbow, 45° 42. Washer, plain 60. Bolt
7. Elbow 24. Fitting, 90° 43. Nut, lock 61. Bolt
8. Riser, tee 25. Adapter 44. Tee 62. Washer
9. Tailpipe 26. Gasket 45. Reducer 63. Nut
10. Clamp 27. Adapter 46. Nut 64. Bolt
11. Wastegate 28. Gasket 47. Adapter 65. Nut
12. Fitting 29. Check valve 48. Fitting 66. Nut
13. Elbow 30. Hose 49. Hose 67. Gasket
14. Gasket 31. Elbow 50. Check valve
15. Bolt 32. Hose 51. Bolt
16. Washer 33. Bracket 52. Washer, plain
17. Nut 34. Clamp 53. Washer, lock
35. Clamp 54. Nut
36. Washer
72-10-50 REVISED OCT 97
72-10-180 EXHAUST SYSTEM REMOVAL AND DISASSEMBLY,
TSIO-360-MB & SB (See Figure 72-10-180).
I
A. Remove hose (32), elbow (31) attaching hardware (36, 37, 38). clamp (34), check
valve (29). attaching hardware (40 through 43), hose (30), hose (20), fittings (23, 24),
clamp (35), check valve (50), hose (49), tee (44), and fitting (45). Remove hose (21)
and fitting (13).
B. Remove attaching hardware (15 through 17) and wastegate (11). Remove and
discard gaskets (1 4). Loosen and remove clamp (10) and tailpipe (9).
C. Remove attaching hardware (60, 61, 62, 63) and turbocharger (18). Remove and
discard gasket (59). Remove nuts (66), risers (3, 4, 5. 6) attaching hardware (64, 65),
elbow (7) and riser (8).
LEFT
BLANK
72-10-52
SECTION 72-20
CLEANING, REPAIR AND
REPLACEMENT
72-20-01
INTENTIONALLY
LEFT
BLANK
72-20-02
72-20-00 CLEANING, REPAIR AND REPLACEMENT
NOTE . . . It is required that all parts listed in Section 1-00-04 100% replacement parts
be replaced during major engine overhaul regardless of condition. Refer to Service
Bulletin M87 -11 Rev. 2, or subsequent revision as applicable.
72-20-01 GENERAL
I
Aluminum alloy parts can be degreased by spraying or brushing with any fortified mineral
spirit solvent. Heavy grease or dirt deposits can be cleaned effectively by allowing parts
to soak in this solvent for a short time. Carbon deposits and gum (oil varnish) may be
removed easily by immersing these parts in a hot bath of an inhibited, mild alkaline
cleaning com-pound. Immersion time should be only as long as necessary to remove the
deposits. Carbon solvent should be employed only when carbon deposits are too hard or
thick for removal by other solvents. Give special attention to cleaning studs, tapped
holes and drilled holes. Caution must be exercised in cleaning of all aluminum alloy
engine parts. Immediately after removing soaked parts from inhibited, mild alkaline bath
or hot soapy water, remove all traces of the alkaline by spraying the parts with a jet of
steam, or brush vigorously with a mineral spirit solvent. Cleaned parts may be dried by a
jet of dry compressed air to remove all solvent liquids.
CAUTION . .. All alkaline residues must be removed from crevices, recesses and holes to
prevent the formation of a foaming emulsion in the engine lubricating oil after
reassembly. If accelagold sUlface was removed by cleaning process, re-apply accelagold
according to procedure listed in paragraph 72-30-12.
No polishing compound, abrasive paste or powder is needed for cleaning engine parts.
Scraping and abrasion with wire brushes, sandpaper, abrasive cloth and buffing wheels
are dangerous methods to use on soft metals like aluminum. Scratches resulting from such
methods allow concentrated stress at the scratch and may cause fatigue failure.
Blasting techniques can be employed to remove hard carbon deposits if suitable equipment
is available. Suitable types of grit for dry blasting are plastic pellets and processed
natural materials, such as wheat grains and crushed fruit pits or shells. Air pressure
should be the lowest that will produce the desired cleaning action. Small holes and
finished surfaces, which do not require cleaning. should be protected from the blast by
seals and covers, particularly if the grit is sharp.
CAUTION . .. Sand, shot, metal grit and glass beads are too abrasive and too heavy for
use on soft metals like aluminum, and must not be used. After any blasting process, blow
off all dust with dry compressed air and make sure that no grit has lodged in crevices,
recesses and holes. Parts may also be cleaned with hot soapy water, then air dried with
dry compressed air.
72-20-02 CYLINDERS. Precautions applicable to both aluminum and steel must be exercised in cleaning
and storing these assemblies. Remove oil and loose material with a mild alkaline cleaner by
spraying or brushing. If stubborn deposits of carbon remain on cylinder heads, the areas
affected may be vapor blasted. All machined surfaces must be protected from abrasive action
during the blasting operation.
72-20-03 PISTONS. {100% Replacement at overhaul.} Do not use wire brushes or scrapers of any kind.
Soft or hard carbon deposits may yield to solvent action. If deposits remain, blast the piston
heads with soft grit or by the vapor blast method, (no glass) first having installed tight
fitting skirt protectors. Ring grooves must be cleaned by pulling lengths of binder twine or
very narrow strips of crocus cloth through them. Do not use automotive ring groove scrapers,
since the corner radii at the bottoms of the grooves and side clearances must not be altered.
72-20-04 VALVES. After degreasing valves, inspect them and discard any whose head is warped excess-
ively, or insufficient stock to permit refacing within specified limits, or whose stem is
burned, scored, eroded or nicked. Carbon deposits may be loosened by solvent action or they
may be scraped off while the valve is rotated in a polishing head or lathe collet. Apply
crocus cloth moistened in mineral spirit, and polish the stems with dry crocus cloth. Replace-
ment of exhaust valves is recommended at major overhaul regardless of condition.
72-20-05 ROCKER SHAFTS. 100% replacement at overhaul. Degrease these parts by brushing on
mineral spirit solvent. Prior to magnetic inspection, polish the steel bearing surfaces with
crocus cloth moistened with kerosene, then with dry crocus cloth.
72-20-06 PUSHRODS, VALVE ROCKERS AND SMALL STEEL PARTS. Degrease these parts with mineral
spirit solvent. Giving special attention to removal of sludge from all oil passages. Blow
compressed air thru pushrod.
72-20-07 CAMSHAFT AND CRANKSHAFT. All parts must be degreased by brushing or spraying with
mineral spirit solvent. Give particular attention to threads, oil holes and recesses. Before
magnetic inspection, the crankpins, main journals, oil seal race of the crankshaft and all
journals, cam lobes and gear mount flange of the camshaft must be smoothed with crocus
cloth, moistened in mineral spirits. This is to be accomplished while shaft is rotated in a
high speed lathe (about 100 RPM). All gum (varnish) deposits must be removed to permit
reliable magnetic indications.
72-20-08 CRANKCASE. The oil passages must be pressure-flushed with mineral spirit solvent and
inspected with the aid of a flashlight. If the castings are immersed in an alkaline bath,
I follow this by spraying with steam followed by flushing the oil passages with solvent. After
the castings dry, inspect them thoroughly for alkaline residues, and remove any traces of
scum.
72-20-09 GEARS. Gears without bushings are freed of hard deposits by immersion in a caustic stripping
bath, when cold solvents are not effective. Bushings are discolored by this treatment, there-
fore, bushed gears must be cleaned by other methods. Spray or brush with a mineral spirit
solvent using a brass wire brush.
I WARNING •.. Do not pressure blast gears, blasting will remove hardened surface.
72-20-10 SHEET METAL PARTS AND INTAKE MANIFOLD. Clean these parts by spraying or brushing
with mineral spirit solvent, or use a cold emulsion type cleaner and flush with water to
rinse.
Immediately after cleaning bare steel parts, spray or dip them in clean engine oil or, for
longer storage, in a corrosion-preventive oil mixture. Wrap ball bearings in waxed paper.
Wrap or cover other clean parts to protect them from abrasive dust in the air.
72-20-12 STUD REPLACEMENT. Remove damaged whole studs with a standard pattern stud remover or
small pipe wrench, turning slowly to avoid heating the casting. Remove broken studs with a
splined stud extractor. (Splined extractors and drills are usually sold in sets.) Examine the
coarse thread end of the damaged stud before discarding it to determine its size. Standard
studs have no marking. For oversize stud identification, refer to Fig. 72-20-128. Clean the
casting tapped hole with solvent and blow dry with compressed air; then examine the thread.
If it is not torn, install the next larger oversize stud. If the old stud was of the maximum
oversize, or if the thread is damaged, the hole may be tapped and a helical coil insert
installed for a standard-size stud. Coat the new stud's coarse thread with High Strength
Adhesive PIN 646941 if the hole is blind or if the hole goes through a cavity subject to oil
leakage. It is advisable to drive the new stud with a tee handle stud driver. Turn it in
slowly, and compare the estimated torque values listed in the Table of Limits. Drive the stud
in until it projects a distance equal to the appropriate "Setting Height" (See Figure 72-20-
12A).
WARNING •.. Helical coil inserts are not to be installed in cylinder mount pads.
NOTE . . . When a Helical coil is used at the sump drain location, all metal particles from the
drilling and tapping process must be removed from the oil sump pan.
72-20-05
1
CRANKCASE
1 Cylinder Mount Pads 3/8-16 X 3/8-24 25/32 36 36 36 36 36 36 36 m36 36 36 36
2 Engine Mount Pads 318-16 X3/8-24
3/8-16 X 3/8-24
3/8-16 X 3/8-24
1.00
1-3/16
1-1/2
4
-
3
4
-
3
4
-
3
4
-
3
:t+
- -
4
4
-
4
-
3
4
-
-
4
4
-
4
4
-
4
4
-
3/8-16 X 3/8-24 1-11116 - - - - 3 3 3 - - 3 3 3
3 Governor Mount 5/16-18 X5/16-24 1-3/8 4 4 4 4 4 4 4 4 4 4 4 4
Pads
4 Fuel Pump Pad 5/16-18 X5/16-24 3/4 4 4 4 4 4 4 4 4 4 4 4 4
5 Oil Sump Pad 1/4-20 X 1/4-28 3/4 14 14 14 14 14 14 14 14 14 14 14 14
6 Crankcase Cover 5/16-18 X5/16-24 27/32 3 3 3 3 3 3 3 3 3 3 3 3
Pad
7 Crankcase Cover 5116-18 X5/16-24 2.00 3 3 3 3 3 3 3 3 3 3 3 3
Pad
8 Shafigear Support 5/16-18 X5/16-24 1-3/8 2 2 2 2 2 2 2 2 2 2 2 2
9 Generator Pad 5/16-18 X5/16-24 13/16 3 3 3 3 3 3 3 3 3 3 3 3
10 Oil Pump Pad 114-20 X 1/4-28 19/32 3 3 3 3 3 3 3 3 3 3 3 3
11 Magneto Pad 5116-18 X5/16-24 45/64 4 4 4 4 4 4 4 4 4 4 4 4
12 Filter Adapter 5116-18 X5/16-24 1.00 - - 3 3 3 3 3 3 3 3 3 3
13 Starter Pad 3/8-16 X3/8-24 1.22 1 1 1 1 1 1 1 1 1 1 1 1
14 Starter Pad 3/8-16 X 3/8-24 1.00 1 1 1 1 1 1 1 1 1 1 1 1
XXXX:XXPOO3 .003
~ Red
XXXXXXPOO6 .006
~ Blue
XXXXXXPOO9 .009
~ Green
Helical coil inserts of wire with a diamond-shaped cross section forming both a male and
female thread. The diameter of the insert, when compressed into a special tapped hole at the
widest part of the wire (between male and female threads), is equal to the nominal screw size.
The special finishing taps size the casting hole so that the pitch diameter of the female
thread of the installed insert conforms to class 3 fit with standard bolt threads or class 4
(tight) fit with standard size studs. The difference in fit is due to a difference in pitch
diameters of bolts and studs, so that only one set of helical con special taps is required for
installation of these inserts in both bolt holes and stud holes. Tap drilling depths and tapping
depth for helical inserts to be installed in blind holes should conform to the recommendations
relative to inserts of length equal to 2 times nominal diameter, as tabulated in the manufac-
turer's Bulletin No. 650-A. Helical coil tap drills and special taps must be run in perpen-
dicular to the machined surface of the casting. Drilling must be done in a drill press after
the casting is firmly supported, clamped and alignment checked. The tap will tend to follow
the drilled hole. For drilling and tapping aluminum alloy castings, use a lubricant made by
mixing one part lard oil with two parts kerosene to prevent overheating of the metal and
tearing of the thread. (Reference Note page 72-20-05)
To remove a damaged helical coil insert, use the proper size of extracting tool for the
nominal thread size. Tap it into the insert so that the sharp edges get a good Qbite", then
turn the tool to the left, and back out the helical coil until it is free. To install a new
insert in a properly tapped hole (after blowing out all liquid and chips), slide it over the
slotted end of the driving mandrel of the proper size of installing tool and engage the driving
tang (bend end) of the helical coil in the mandrel slot; then wind the insert slowly into the
tapped hole (See Figure 72-20-13). The outer end of the insert should lie within the first full
thread of the hole. Break off the driving tang of a notched helical coil by bending back and
forth across the hole with longnose pliers or with a special tang break-off tool.
72-20-14 SPARK PLUG HOLE HELICAL COIL INSERTS. Before attempting to back out a damaged
insert, use a sharp pointed tool to pry the teeth at outer end away from the cylinder head
metal (See Figure 72-20-14A). Using a pair of pliers, remove the old helical coil from cylinder
(See Figure 72-20-14B). Place a new helical coil in the cut-out side of the installing tool
sleeve with its driving tang toward the threaded end. Engage the tang with the slotted end
of the driving mandrel and wind the insert into the sleeve so the helical coil can be seen
through the slot in the threaded end, and turn the mandrel crank until the insert starts into
the cylinder head hole. If the sleeve is not in contact with the head surface, grip sleeve and
mandrel and turn until the sleeve touches lightly (See Figure 72-20-14C). Wind the helical
coil into the cylinder head until its toothed end lies within the first full thread. The teeth
should be in position to enter the depressions made by the original insert. If driven too far,
the insert will emerge in the combustion chamber and will have to be wound on through.
When the helical coil is in correct position, use longnose pliers to bend the driving tang back
and forth across the hole until it breaks off at the notch. Coat a Heli-Coil Corporation No.
520-2 expanding tool threaded end with Alcoa thread lube or a mixture of white lead and oil,
and screw it into the new insert until its final thread forces the teeth firmly into the
cylinder head metal (See Figure 72-20-140).
72-20-08
FIGURE 72-20-14A. PRYING SPARK PLUG FIGURE 72-20-140. EXPANDING SPARK PLUG
HELICAL COIL AWAY FROM CYLINDER HOLE HELICAL COIL INSERT
SECTION A·A
72-20-09
5.963
5.953
1.------6.375
....
1
REF-----~ .5"1~:' ~~~M
"Y" REF BOTTOM OF
5.965
5.955
"D"DlAMETERllnches\
SIZE NEW PART SERVICE LIMITS
MINIMUM MAXIMUM MAX.
STANDARD 4.437 4.439 4.442
.005 4.442 4.444 4.447
.015 4.452 4.454 4.457
"X"DIAMETER (Inches)
SIZE NEW PART SERVICE LIMITS FOR
MINIMUM MAXIMUM "X" DIA. IS ACTUAL
STANDARD 4.434 4.436 MEASURED"D"DlA.
.005 4.439 4.441 PLUS .001 In.
.015 4.449 4.451
CAUTION: Cylinder assemblies exceeding new parts dimension shown are acceptable when performing
maintenance before engine overhaul. However, piston ring gaps given in the table of limits should be
maintained. When engine is being overhauled, TCM requires that all parts be brought back to new parts
limits by rework or replacement. Installed parts should never exceed Service Limits. See Section 72-30-
07 New Parts and Service Limits.
I
and previous breakage have removed as much as 10% of the total head fin area, the cylinder
assembly has reached the limit of its repair and the cylinder must be replaced.
72-20-16 VALVE GUIDES REMOVAL AND INSTALLATION. (See TCM Service Bulletin M85-18 or current
revision as applicable.) Intake valve seat refacing figure 72-20-28A. Exhaust valve seat
refacing figure 72-20-28B.
Use heavy duty drill press and Borroughs No. 5221 Holding Fixture or equivalent to hold
cylinder. DO NOT ATTEMPT PROCEDURE BY HAND.
1. Use a No. 4981 Remover. Select proper size head. Install on removing handle. Attach
to cold water supply.
2.
3.
Heat cylinder to 450°F. Heat soak one hour.
Install pilot into guide. Hold down firmly into guide bore with hand on water
I
release button. Use other hand to work sliding hammer. Release the water and
hammer out guide while water is running. Both guides can be removed with one
heating. Support cylinder with barrel up. Use wooden blocks to keep from damaging
rocker cover surface.
VALVE GUIDE INSTALLATION. TCM requires the next OIS guide to be used.
1. Measure valve guide boss and select proper No. 4914 or No. 4943 series reamer to
ream valve guide boss to required oversize. Consult Table of Limits Figure 72-30-08
for proper interference fit. Guide boss must be clean and free from pits or grooves.
Run reamer through first. If bore is not clean, go to next larger size reamer. Use
No. 2849 Plug Gages to check fit.
2. Heat cylinder head to 450°F. and install frozen guide with No. 4912, No. 2842, or
No. 3619 Replacer. A small amount of lubricant oil on the guide will reduce the
chance of binding during installation.
1. Install No. 5221 B Holding Fixture or equivalent into drill press to hold cylinder. DO
NOT ATTEMPT PROCEDURE BY HAND.
2. Index fixture to proper angle and install cylinder into fixture. Zero in guide with
dial indicator.
3. Select proper reamer from Borroughs Tool Catalog. Ream at 400 RPM for high speed
steel reamers and 700 RPM for Carbide tip reamers (Do not use carbide tip reamers
for hand cutting) with plenty of lubricant.
4. Check finished bore with the correct plug gage. Refer to Table of Limits Figure 72-
30-08 for correct stem hole finished sizes.
NOTE . . . See TCM Service Bulletin M85-18 or current revision as applicable for
further information. All tool numbers are Borroughs PIN's.
72-20-18 HYDRAULIC VALVE LIFTERS (See Figure 72-20-18). Stand valve lifter on its flat end. Use
a small screwdriver and carefully pry snap ring (1) from body groove, holding down socket (2)
with a pushrod until ring has been removed. Invert lifter and catch socket as it drops out.
Insert a finger into plunger (3) and withdraw plunger (3), spring (7) and check valve assembly
(3, 4, 5, 6). If plunger is stuck in body (8), hold plunger down fully and scrape out carbon
deposit. If this obstruction cannot be removed, or if plunger is seized by score marks, the
entire assembly must be replaced. Remove spring (7), by turning as if to unwind it while
pulling outward. Be careful not to stretch spring out of shape. Remove check ball (4) from
plunger by removing retainer (6), lifting spring (5) and ball (4).
NOTE. .. If major engine overhaul, hydraulic valve lifters are recommended 100% replacement.
1. Ring, Retaining
2. Socket, Hydraulic Lifter
3. Plunger
4. Check Ball
5. Ball Check Spring
6. Ball Check Retainer
7. Spring Plunger
1 8. Body Valve Lifter
b
FIGURE 72-20-18. HYDRAULIC LIFTER.
CAUTION. . . In order to assure good dynamic balance, connecting rod assemblies for new
engines are selected in pairs with a maximum weight variation of 1/2 ounce in opposite bays.
This limit cannot be maintained if material is removed from any of the original in a set.
Therefore, rods are supplied in matched sets only.
72-20-20 PISTON PIN BUSHING REPLACEMENT. TCM recommends connecting rod Piston Pin Bushing
be replaced 100% at overhaul. The connecting rod does not need to be heated for this
operation. Press out the old bushing in an arbor pmss, using a drift only slightly smaller
than the bushing 0.0. Make sure that the rod bore is smooth. Dip the new bushing in
engine lubricating oil before placing it in position, and locate the split as illustrated in Figure
72-20-20. (The position number is stamped on the rod and cap bosses on the far side.) Ream
or bore the new bushing to the specified diameter and check alignment as described in
paragraph 72-40-05. The center-to-center distance given in Figure 72-20-20 will be held
automatically if the bore is centered in the new bushing.
WARNING •.• Do not nick or damage connecting rod I beam when installing or removing
from holding fixture.
72-20-12
.OOOSIN. MAX. CONVERGENCE OF BREAK SHARP EDGES .015IN. X
THESE AXES PER INCH OF LENGTH 45°. IF ORIGINAL CHAMFER WAS
(WITH NEW BUSHING) COMPLETELY REMOVEO BY BORING
OR REAMING OF REPLACEMENT
BUSfilNG.
6377 - - - - - - - - - - 1
f - - - - - - - - 6.373
STAMP CYL. POSITION NUMBER ON NEW RODS
(TO BE INSTALLED ON TOP)
I
_---+Ht---7f----rf'}:;> I . ... .. ..... '\-Il-=-
-:::::;~===~~~====~<::::"= .,,:,,;/
ill
A
-+
~~~.~~IST
j
::::.::::: I
BUSHING
(WITHNEW
BUSHING)
l--;S J-- \
(SPLIT TO BE LOCATEO
AS SHOWN) Il BIG END
WEIGHTS OF RODS IN ANY ENGINE MUST BE SAME WITHIN Y.. OZ. IN OPPOSITE BAYS.
72-20-21 CRANKSHAFT ASSEMBLY. Raised edges from small nicks on hard surfaces such as crankpins
and journals, can be removed with a hard Arkansas stone. Do not use a coarse abrasive. Do
not attempt to remove deep scoring or indications of overheating which render the crankshaft
unserviceable. Polish crankpins and main journals with long strips of crocus cloth while the
shaft is rotated about 100 RPM in a lathe. Since gears are shrunk fit to the crankshaft, it
may be necessary to dip the gear in oil heated to 300°F. before removal. These operations
should precede magnetic particle inspection.
Hardened steel bushings in the crankshaft blades must be removed and replaced if excessively
worn. It is recommended that these bushings be replaced during major engine overhaul
regardless of condition. It may be necessary to chill the old bushings to free them. New
bushings must be chilled before installation, and the holes must be smooth. No finishing
operation is required for the new bushings, since they are made to final dimensions. They
must be pressed into the same positions as the original parts.
NOTE . . . Crankpins and crankshaft main journals may be reground to the allowable 0.010
inch undersize. Reground crankshafts must be re-nitrided.
CAUTION. . . Crankshaft cOlilltelweighls are matched in pairs with a maximum weight varia-
tion of 2 grams, and the complete crankshaft and counterweight assembly is dynamically
balanced. As a result, if either cOllnte1weight is damaged, it will be necessary to discard both
Oil that cheek alld procure a matched pairfor replacement.
72-20-13
72-20-22 MAGNETO GEAR SUPPORT SHAFT. The magneto gear support shafts should be removed from
the crankcase, cleaned and inspected using the same procedure outlined for rocker shafts 72-
20-05. Refer to dimensions given in Table of Limits to determine if shafts are serviceable.
72-20-23 MAGNETO AND ALTERNATOR DRIVE COUPLINGS. TCM recommends 100% replacement of
magneto drive coupling roller bearings and all rubber drive bushings at engine overhaul.
Inspect drive gear teeth for excessive wear, pitting or corrosion. Clean and inspect steel parts
using magnetic particle inspection. Refer to the Table of Limits for serviceable limits and
tolerances.
72-20-24 TACHOMETER DRIVE HOUSING. Remove the oil seal with a suitable puller. If the housing
counterbore is scored, smooth it with crocus cloth. Spread a film of grade 50 MHS 27 oil on
the perimeter of a new seal, then press the seal squarely into the housing with its lip outward
facing the oil source.
72-20-25 STARTER DRIVE ADAPTER. The clutch spring sleeve is pre-shrunk and doweled into the
housing. If it is necessary to remove the needle bearing in the adapter, a removing driver
may be purchased (See Section 1-20-01 Tools Figure 45).
Hole diameter must be .0918-.0968 to reduce possibility of clogging and causing lubrication loss
to the starter adapter clutch spring. The oil feed hole comes off the rear cam bearing of the
1-3-5 crankcase half and intersects a short hole in the center of the needle bearing counter-
bore. Hole can be enlarged to diameter shown above after removal of the starter adapter.
72-20-26 OIL PUMP ASSEMBLY. Replace worn gears, bushings and studs. Nicks on parting flanges
may be stoned out. The pump gear chamber must not be enlarged. If it is scored or the
driven pump gear pilot shaft is loose, TCM recommends 100% replacement of the accessory
case. Heavy scoring on the gear contact area of the oil pump cover renders this part
unserviceable and replacement is mandatory.
72-20-27 IGNITION CABLE. All ignition cable assemblies or harness assemblies must be replaced at
each overhaul. If the high tension outlet plates are in good condition, new cable assemblies
may be installed on them. On TCM harness assemblies, push the cable end through the outlet
plate and install the inner ferrule, grommet and outer ferrule (eyelet) onto cable center wire.
On Slick harness assemblies, push the cable end through the outlet plate and install the
tapered drive ferrule, press drive ferrule into outlet plate, install insulator sleeve, spring on
electrode screw and screw into cable end.
Observe the "1" mark on the exterior side of each outlet plate adjacent to the No. 1 cable
outlet hole, (Refer to Figure 72-20-27), and observe that the numerals appearing at the spark
plug ends of the high tension leads indicate the cable to cylinder position. Complete installa-
tion of high tension cables into outlet plate insuring their proper location according to wiring
diagram 72-20-27. Refer to Chapter 74 for further information regarding magnetos and
ignition harnesses.
72-20-14
UPPER SPARK PLUGS
60---,
5
4
3
IGNITION SWITCH
2
2
3
4
5
6 Lr-------------------------------J
LOWER SPARK PLUCS
72-20-15
.,.-.-----2.09 DIA. MAX.----~
1'1-----2.01 DIA. MAX - - - - - t o !
I
VENTURI INSERT
PROCEDURE:
1. CLEAN UP SEAT WITH 300 STONE.
2. TOP OFF WITH 1S- STONE TO ESTABLISH 2.01 MAX SEAT 0.0.
AS REQUIRED.
4. For approximate amount to be removed from stem tip, measure from position of new gage diameter to
valve stem tip. Subtract 4.249 from new length, the remainder will be the amount to be removed from
valve stem tip.
5. After grinding, measure overall length 9f valve if new overall length is less than 4.352 long discard valve
and replace with new.
~________~_.OO8_G_A_P_M_AX
__•__________~
j
I
(
OVERALL
LENGTH MUST 4.246 FROM STEM TIP
BE4.3520R 4.252 TO GAGE DIM LINE
GREATER
AFTER GRINDING
STEM TIP, IF NOT
DISCARD VALVE
r- FACE
LEFT
BLANK
72-30-00 INSPECTION
72-30-01 General
72-30-01
INTENTIONALLY
LEFT
BLANK
72-30-02
72-30-00 INSPECTION
72-30-01 GENERAL
The following definitions apply to terms used to describe kinds of damage for which parts
should be inspected.
ABRASIONS: Scratching of a surface, either by motion while in contact with another part, by
mechanical cleaning, or resurfacing with abrasive cloth or lapping compound.
BURNING: As applied to valve heads, this term indicates roughening or erosion due to high
temperature gases escaping past valve faces. In other instances, it indicates drawing of the
temper of steel parts to a soft (blue) condition as a result of overheating, in absence of
lubrication on moving surfaces such as gear teeth, subject to high loading.
BURR: A sharp projection of metal from an edge, usually the result of drilling, boring,
countersinking, etc., but may also be caused by excessive wear of one or both surfaces
adjacent to the burred edge.
GALLING: Excessive friction between two metals resulting in particles of the softer metal
being torn away and ''welded'' to the harder metal.
PITTING (OR SPALLING): Small, deep cavities with sharp edges. May be caused in hardened
steel surfaces by high impacts or in any smooth steel part by oxidation.
RUNOUT: Eccentricity or wobble of a rotating part. Eccentricity of two bored holes or two
shaft diameters. A hole or bushing out of square with a flat surface. Usually measured with
a dial indicator, and limits stated indicate full deflection of indicator needle in one revolution
of part or indicator support.
SCORING: Deep grooves in a surface caused by abrasion, when fine, hard particles are forced
between moving surfaces, as in a bearing and journal, or by galling when a moving part is not
supplied with lubricant.
PROTECTION FROM CORROSION: Coat all steel parts with corrosion preventive oil. At
inspection, parts are wiped free of oil, to provide easy handling and true dimensional readings.
Immediately after inspection, parts must be cleaned to eliminate fingerprints and contaminates,
completely recoated with corrosion preventive oil and packaged properly to prevent damage.
72-30-03
72-30-02 VISUAL INSPECTION. Parts without critical dimensions, small parts, running parts, and others
of major importance, must be inspected visually with at least a 10X magnifying glass under
good light for surface damage such as nicks, dents, deep scratches, visible cracks, distortion,
burned areas, pitting, pick-up of foreign metal, and removal of enamel coating. Visual
inspection should also determine the need for further cleaning of obscure areas. Inspect all
studs for possible bending, looseness or partial removal. Inspect all threaded parts for nicks
and other damage to the screw threads. After visual inspection, the engine parts should be in
three groups: Apparently serviceable parts, repairable parts and parts to be discarded.
72-30-03 MAGNETIC PARTICLE INSPECTION. Inspection by the Magneflux method must be conducted
on all ferrous parts listed in Section 72-30-03, and in accordance with the methods and data
in the table before dimensional inspection. The Magnaglow method is recommended whenever
the necessary equipment is available. This method employs magnetic particles coated with a
fluorescent organic material which may be illuminated with a "black light", as in the Zyglo
process, to amplify an indication of weakness. If a crankshaft is doubtful after a circular
magnetization and inspection, demagnetize and remagnetize it longitudinally for further
inspection.
NOTE. . . Before magnetic particle inspection, piston pins and valve rocker shafts must be
polished with crocus cloth.
CAUTION. . . Before magnetic particle inspection of any part, plug small holes leading to
obscure cavities with tight-fitting wood plugs or with a hard grease which is soluble in
lubricating oil to prevent particles from lodging in places where they would be difficult to
remove, and in places that are not subject to visual inspection. After magnetic particle
inspection, remove all such plugs and clean the part thoroughly in solvent, and dry with
compressed air. Check for complete demagnetization.
72-30-04
72-30-03
*Method of AC or DC Possible
Part Magnetization Amperes Critical Areas Defects
Piston Pin Circular and 1000 Shear planes, ends, Fatigue cracks.
Longitudinal center
Rocker Arms On Conductor Bar 1000 Pad, socket under Fatigue cracks.
and Single side, arms and boss.
Between Heads 800
Gears over 6 Inch Shaft, Circular 1000 to Teeth, Splines. Fatigue cracks.
Diameter Teeth Between 1500
Heads Twice
, 90° Apart
Thru Bolts Circular and 500 Threads Under Head. Fatigue cracks.
Rod Bolts Longitudinal
NOTE: (*)
CIRCULAR MAGNETISM: Current passed through work or through non-magnetic conductor bar
inserted through work.
72-30-05
72·30-04 CRANKSHAFT ULTRASONIC INSPECTION PROCEDURE.
I Refer to Service Bulletin CSB96-10, or current revision.
A. PURPOSE. To provide a procedure for ultrasonic inspection of crankshaft intermediate
main bearing journal fillet areas.
B. METHOD. This procedure describes the use of a shear-wave, pulse-echo, angle-
beam ultrasonic inspection technique.
The sound enters at one end of the main bearing journal and propagates through the
steel at a 45° angle. The sound reaches the crankshaft center hole and is reflected
back up into the region of the fillet at the other end of the sarne journal.
If an ultrasonic reflector, in the form of a crack, exists in the region, the sound is
reflected back along the same path to the surface applied transducer, and displayed
as a signal on the screen of the inspection instrument.
In the absence of a reflector in the region into which the sound is directed, no signal is
displayed.
C. EQUIPMENT.
1. Instrument. Krautkramer Branson Model USK 7D, USL 42, USL 48, USN 50, USN
52 or OR7S
2. Probe. Miniature Transducer Gamma Series 5 MHz Krautkramer/Branson Cat.
#MSWS 224-580.
3. One each of the following reference standards:
PIN 654478-1
PIN 654483-1
PIN 654485-1
4. The following shear wave wedges are required:
PIN 654578
PIN 654484
5. Couplant. SAE 50 weight lubricating oil.
1
3
4
10
7
12
8
Accessory case
1 Oil pump gears in housing . . end clear: 0.006 0.001 0.004
2 Oil pump gears in housing . dia: 0.006 L 0.0015 L 0.004 L
3 Oil pump gear shafts in housing. dia: 0.004 L 0.0005 L 0.002 L
4 Oil pump gear shafts in cover. dia: 0.004 L 0.0005 L 0.002 L
5 Oil pump driven gear on shaft. . dia: 0.004 L 0.0005L 0.0020
6 Alternator pilot in cover. . . . . dia: 0.001 L 0.005 L
7 Oil seal in alternator . .. . . . dia: 0.002 L 0.008 T
8 Alternator coupling retainer on sleeve . dia: 0.032 L 0.016 L 0.026 L
9 Coupling retainer in coupling hub slot . side clear: 0.020 L 0.005 T 0.015 L
10 Coupling bushings on drive gear lugs
(replace if worn) . .. . . .
~ side clear: 0.039 L O.043T
11 Oil pump driver-to-driven gear . . . backlash: 0.027 0.014 0.0218
12 Alternator gear-to-camshaft gear . backlash: 0.0019 0.010 0.014
13 Driver gear shaft in oil pump drive gear. dia: 0.003 L 0.0005 L 0.002 L
14 Drive gear-to-camshaft gear . . . . backlash: 0.019 0.010 0.014
Oil temperature control valve 0.090 inch
minimum travel at . ... . temperature: 120°F. HO°F.
Valve must be fully closed against seat at . temperature: 168°F. 172°F.
Valve must crack open at 180°F. . . . PSI: 181bs.
011 Pressure Relief Valve Spring Tension Values Are For Troubleshooting Purposes
ONLY. 100% Replacement At O/H.
12-30-09
FIGURE 72-30-08
TABLE OF LIMITS
(CHART 2)
I 1
2
3
Cylinder bore (lower 4 1/4/1 of barrel~
Cylinder bore (1/1 from top of barrel) .
Cylinder bore (see Figure 72-20-15) .
diameter:
diameter:
taper:
Refer to Figure 72-20-15
I
Refer to Figure 72-20-15
0.001 I 0.002 0.0035
4 Cylinder bore out-of-round . tolerance: 0.002 0.000 0.001
5 Cylinder bore (reground 0.015/1). . allowable o/s: Refer to Figure 72-20-15
*6 Cylinder bore surface roughness (Nitrided Barrels)
using 180 grit stone, cross hatch angle: - 22°-32° -
Microfinish (measured in
direction of piston travel) . RMS: - 15 25
*6 Cylinder bore surface roughness (Channeled Chrome)
using 180 grit stone, cross hatch . angle: - 22°- 32° -
Finish all area within ring travel. Must show evidence
of contact with honing stone. Partially honed areas
shall not exceed 10% of bore surface and no area shall
exceed one inch in any direction.
*6 Cylinder bore surface roughness (Cermicrome)
Finish - pitting is undesierable if present, it is
subject to the following limits:
Pits (No more than two pits in any 1/4 inch
Dia. circle) diameter: - - .031
Not more than 25 pits of anyone size in entire
cylinder bore is acceptable.
7 Cylinder barrel in crankcase diameter: 0.003L 0.011 L
8 Intake valve guide in cylinder head diameter: 0.0011T 0.0026T
9 Exhaust valve guide in cylinder head diameter: 0.0011T 0.0026T
10 Exhaust valve seat (to valve guide axis) angle: 44° 30' 45° 00'
11 Intake valve seat (to valve guide axis) . angle: 59° 30' 60° 00'
12 Intake valve seat insert in cylinder head diameter: 0.0055T 0.0085T
13 Exhaust valve seat insert in cylinder head diameter: 0.0070T 0.0100T
H 6
7
18
Intake valve in guide.
Exhaust valve in guide .
Intake valve face (to stem axis) .
diameter:
diameter:
angle:
0.005L
0.008L
0.0010L
0.0030L
59° 45'
0.0040L
0.0080
60° 15'
19 Intake valve (max. tip regrind 0.Q15/1). length: 4.337 4.352 4.368
20 Intake and exhaust valve
(full indicator reading) . warpage: 0.004 0.000 0.002
21 Valve rocker toe to valve stem (dry lifter) . . . . 0.060 0.200
22 Rocker Arm. side play: .005 .035
23 Rotocoil to rocker arm clearance . clearance: .020
FIGURE 72-30-08
TABLE OF LIMITS
(CHART 2)
30 31 32
14
FIGURE 72-30-08
TABLE OF LIMITS
(CHART 3)
Ref. Serviceable New Parts
No. Descriotion Limit Min. Max.
CRANKCASE
1 Through bolts in crankcase. diameter: 0.0007T 0.0011 L
2 Hydraulic valve fifter in crankcase. diameter: 0.0035L 0.001L 0.0025L
3 Hydraulic valve fifter bore in crankcase. diameter: 1.0005 1.0015
4 Governor driven gear in crankcase diameter: 0.005L 0.0014L 0.0034L
5 Governor driven gear bore in crankcase. diameter: 0.875 0.876
6 Starter shaft bushing in crankcase. diameter: 0.0005L 0.001T
7 Crankcase main bearing bore. diameter: 2.437 2.438
8 (j) Crankcase rear and intermediate main
bearing bore . diameter: 2.5625 2.5635
9 (j) Crankcase front main bearing bore . diameter: 2.437 2.438
10 Crankcase camshaft bearing bore. diameter: 1.3745 1.3755
11 Fuel pump adapter pilot in crankcase . diameter: 0.001L 0.005L
12 Fuel pump body pilot in adapter. diameter: 0.0005L 0.0045L
13 Oil seal in adapter. diameter: 0.003T 0.009T
14 Fuel pump drive shaft in impeller shaft . diameter: 0.011L 0.002L 0.008L
15 Fuel pump drive shaft in governor gear. tooth clear: 0.0055 0.0015 0..0039
72-30-12
Ref. Serviceable New Parts
No. DescriDtion Limit Min. Max.
72-30-13
1 3 2 6
7 4 5
73-30-08
TABLE OF LIMITS
(CHART 4)
72-30-14
STARTER ADAPTER AND SCAVENGE PUMP COVER
FITS AND LIMITS (OLD STYLE) SEE CHART SA.
8,11
1,2
7 6
DETAIL A
"A" "B" "c"
CD These fits and limits apply to both old style and new style starter adapter and scavenge pump
cover assemblies.
BREAK DETAIL A
EDGE
.......1IIt--SMOOTH TAPER BETWEEN
DIAMETERS B & C
SURFACE 32 RMS
........- .75
.81
-~
.40-of.....- .......
~
,
"'A" "8"
DETAIL A
NOTE ... See the new style starter adapter and accessory drive adapter fits and limits (Chart 5H)
for fits and limits relevant to both old and new style starter adapters.
1,2
35
36
'--"""-- 37
LEFT
BLANK
72-30-15 L
2
FIGURE 72-30-08.
TA8LE OF LIMITS CHART (58)
ALL LfT TS10-360 EXCEPT TSI0-360A.
72-30-16
FIGURE 72-30-09
CRITICAL NEW PART DIMENSIONS
72-30-09 ORIGINAL DIMENSIONS. Although comparative measurements of mating parts will determine the
serviceability of the fit, it is not always easy to determine which part has worn the most, and
in some instances (e.g., main journals in new bearing inserts), accurate measurements of fit are
not possible. While no limits of wear on critical dimensions have been assigned to specific
parts, it is helpful in estimating wear to know the original dimensions. Therefore, manufactur-
ing limits "Critical New Parts Dimensions", in Section 72-30-09, should be consulted when the
serviceability of a specific part is in doubt.
72-30-10 PROTECTIVE COATING. The manufacturer protects all aluminum alloy castings, sheet metal and
tubing from corrosion by treating all surfaces of the parts with Accelagold" (Turco Products,
3300 Montreal Industry Way, Tucker, Georgia, 30084).
72-30-11 APPLICATION OF "ALODIZING". After any machining or repair operation, aluminum surfaces
must be "Alodizing". Surface color may vary from light gold, to dark brown. The "Accelagold"
coating on mating or bearing surfaces is thin enough that it has no effect on dimensional
tolerances. If the original "Alodizing" finish has been removed or deteriorated, "Accelagold" can
be reapplied as described in the manufacturer's Technical Service Data Sheet No. AL-1200-D.
Wrought or die cast, (smooth surface parts such as valve rocker covers and intake tubes), are
"tumble blasted", prior to machining, to roughen surfaces before treatment. ''Tumble blasting"
must not be applied at overhaul on parts with machined surfaces.
72-30-18
If the original "Alodizing" finish has been removed or deteriorated, "Accelagold" can be
reapplied as described in the manufacturer's Technical Service Data Sheet No. AI-1200-D.
CAUTION. .. Do not use enamel paint or primer for internal parts, as it may flake or break off
during engine run and contaminate lubricating oil.
72-30-12 REPAIR OF "ALODIZING" SURFACES. If parts have been machined, rubbed, or scratched with
abrasives in handling, so as to expose areas of bare aluminum, the surface may be repaired by
local application of Accelagold" solution in the following steps.
A. Clean bare area thoroughly with carbon tetrachloride. Do not under any circumstances use
an oil base solvent or strong alkaline cleaner.
B. Mix a small quantity of hot water (180°F.) with 1-1/2 to 2 ounces of "Accelagold" powder
to form a paste, then gradually dilute with hot water until a solution of one gallon is attained.
This solution is to be adjusted by addition of nitric acid to a PH value of 1.5 to 1.7.
C. Apply solution with a rubber set paint brush in such a manner that solution flows over
bare area. Allow solution to remain on the part from one to five minutes or until color of the
new film is approximately the same as original.
D. Flush part with clear water and dry with warm air current. Do not air blast or rub with
cloth to dry new film area. If color is too light, repeat step "C" until desired color is obtained.
NOTE: . . If "Accelagold" does not adhere to metal, a more severe cleaning method must be
used. 12 to 14 ounces of Oaktite No. 61, or equivalent solution, per gallon of water is prefer-
red. Apply and remove the solution with caution. An alkaline cleaner of this type will remove
any "Accelagold" film previously applied. Remove cleaning solution thoroughly with plenty of
hot water and vigorous brushing.
72-30-13 ENAMEL COATINGS. Ferrous parts, when painted with gold enamel, will be baked with infrared
equipment for 15 minutes at 274-285°F. following application of each coat. Magnesium parts will
be pickled and primed before painting; then baked with infrared equipment for 15 minutes at
275-285°F following application of each coat of enamel.
NOTE. . . If a part which was originally "Alodizing" is to be refinished with enamel, it will not
be necessary to apply zinc chromate primer except to the surface areas completely stripped of
"Accelagold".
CAUTION. . . Before application of primer and enamel to a part, carefully mask all connection
joints and mating sUifaces. No primer or enamel is permissible on interior sUlfaces of any parts
contacted by engine lubricating oil after assembly.
72-30-19
INTENTIONALLY
LEFT
BLANK
72-30-20
SECTION 72-40
SPECIFIC INSPECTION
72-40-01 Crankcase
72-40-02 Crankshaft
72-40-04 Camshaft
72-40-06 Gears
72-40-08 Cylinders
72-40-01
INTENTIONALLY
LEFT
BLANK
72-40-02
72-40-00 SPECIFIC INSPECTIONS.
72-40-01 CRANKCASE. If any cylinder base nut was loose at disassembly or if any of the cylinder
attaching studs are bent, even slightly, or if there is definite evidence that a cylinder was
loose at any time, then it is possible that reversal of stress has fatigued the studs and through
bolts installed on that cylinder pad, in which case all of them must be replaced. Test for bent
studs with a toolmaker's square. When inspecting for casting cracks, pay particular attention to
areas on and adjacent to the cylinder mount pads, tappet guides, bottom flange, and bearing
bosses. Look for nicks on machined surfaces and scoring in shaft bearings and the shaftgear
bushing. The castings must be torqued together at a/l attaching points before dimensional
inspection of camshaft and crankshaft bearing bores. If camshaft bearings are excessively worn,
I
the crankcase may be line bored for a 0.020 inch oversized camshaft.
NOTE . . . For cracked crankcase, (See TCM Service Bulletin M90-17 or current revision as
applicable).
72-40-02 CRANKSHAFT. In addition to magnetic particle, ultrasonic visual inspection, and dimensional
inspection, the shaft should be mounted on matched vee blocks on a surface plate (supporting
the front and rear main journals) and rotated under a dial indicator placed on the center rnain
journal in order to detect excessive bending. This is important if the aircraft has been involved
in an accident resulting in a broken or bent propeller. (Refer to the Table of Limits 72-30-09
for limits of "run-out" at the center journal).
NOTE ... In case of prop strike (sudden stoppage), refer to TCM service bulletin M84-16
or current revision as applicable.
NOTE .•• Crankshaft damper blades and counterweights must be magnafluxed twice. Once
prior to installation, and again after installation.
A. At each normal major overhaul, the pins and bushings are replaced. Worn or out of
round counterweight bore will require counterweight replacement.
B. After removing the bushings from the dampeners or the crankshaft blades, measure the
inside diameter of the holes. The replacement bushing must have an interference fit of
.001 "-.003" into each of the counterweights or the crankshaft blade holes.
C. Counterweight pins are identified by dash numbers stamped on one end. Because the
dampener order is controlled by this pin diameter, it is imperative that only the correct
pin, properly identified, be used.
D. Install plates and pin with rough or sharp edge toward outside.
E. Replacement bushings are available in standard .0015, .003 and .005 oversize on the
outside diameter.
72-40-05 CONNECTING RODS. Because of the close tolerance required TeM recommends using an airgage
with correct size air plug and master setting ring to measure all worn bushings and locally
replaced bushings. If a bushing was replaced locally, it is also necessary to check its alignment
with the big end bearing seat. The simplest method of making alignment measurements requires a
push fit arbor, preferably at least eight inches long, for the bushing bore and another for the
bearing seat, a surface plate, two matched vee blocks and two blocks of ground flat steel stock
of equal height. To measure twist, insert the arbors into the rod bores; then lay the big end
arbor in the vee blocks on the surface plate, and place the ground steel blocks under the ends
of the bushing arbor at a measured distance apart. A feeler gage may be used to detect any
clearance at either end under the bushing arbor. This, divided by the separation of the blocks in
inches, will give the twist per inch of length. (Refer to Section 72-30-08, Table of Limits.) To
measure bushing and bearing convergence, mount a dial indicator on a surface gage, and swing
the rod around the big end arbor to the vertical position against a firm stop. Pass the indicator
over the bushing arbor at points an exact number of inches apart. The difference in readings at
the two ends, divided by the distance between points of measurements, again gives the misalign-
ment per inch, as specified in Section 72-30-08, Table of Limits.
72-40-06 GEARS. Inspect gear teeth for signs of overheating and excessive wear. Normal wear produces
a fine polish on the tooth thrust faces. Alteration of the tooth profiles, score marks and
pitting are sufficient cause for rejection.
72-40-07 PISTONS AND RINGS. Inspect the skirt for long, deep scores which indicate overheating and
would be sufficient cause for rejection. If a telescoping gage is used to measure the pin bore,
do not allow the spring pin to extend rapidly so as to strike the wall hard. Visually inspect for
thorough cleaning, including the oil relief holes in the third ring groove. It is NOT necessary to
remove light scores or discoloration from the exterior surfaces; do not use abrasives (including
crocus cloth) on the skirt, since the cam-ground contour should not be altered. If the piston is
dimensionally serviceable in other respects and apparently sound, measure side clearances of new
rings, after measuring the ring gap as follows:
I A. MEASURE RING CAP IN CYLINDER Refer to Service Bulletin M88-11 and M91-4 or current
revisons as applicalbe.
Piston ring gap should be measured whenever a cylinder is removed for repair or overhaul.
Insert ring into cylinder as illustrated in Figure 72-40-07B. Next, insert piston without rings
installed into cylinder. Push piston down until piston ring is at a depth of 6.22 from bottom of
cylinder skirt. Push piston leaving ring squared at 6.22" depth. At this point measure the ring
gap with a feeler gage. Duplicate procedure for 2nd and 3rd ring at same depth. The forth ring
is measured at 1.00". If gap is too tight according to Table of Limits, file ring to within limits
and polish end with an Arkansas stone. If gap is too large go to a 0.005 inch oversize ring to
reach Table of Limits.
After piston rings have been checked for ring gap, install rings on piston. Do not allow their
sharp ends to scratch the piston lands. Make certain part number is toward piston head. Now
measure ring side clearance as follows:
1. Hold a straight edge against the side of the piston ring grooves adjacent to the piston pin
relief, as show in figure 72-40-07A. . .
REF. TO 72-40-07 I
2. Turn piston rings until the gap of each ring is 90 degrees from the straight edge.
3. Push lightly on the piston ring, on the side opposite the straight edge, until ring is in
contact with straight edge. Do not push the secured straight edge away from the piston.
4. Insert feeler gage, to approximately 1/8 inch depth, between top of piston ring and top of
piston ring groove, next to straight edge. Check the Table of Limits for the approved side
clearance dimension.
NOTE. . . It is recommended that piston rings be replaced whenever the cylinder is honed and
pistons and rings be replaced at overhaul per current "Major Overhaul 100% Replacement Parts"
Service Bulletin.
72-40-08 CYLINDER. Inspect cylinder barrels in accordance with Section 72-30-03 and the alloy portion
in accordance with 72-30-05. Failure of either test is cause for rejection. Measure barrel bore for
out-of-roundness in two locations, (in the area between) "X" and "Y" reference points, Figure
72-20-15, and at the 4.25 inch location measured from the open end of the barrel.
To determine wear in cylinder-bore taper (Figure 72-20-15) perform the following: measure "0"
diameter one inch from open end of barrell, measure "X" and "Y" diameter at reference points
indicated. "0" and "X" service limits are acceptable prior to TBO. Cylinder must be replaced or
reworked to "New Parts" limits at overhaul.
TCM recommends oversize boring (.005, .010, .015) of a cylinder found not to be within the,
out-of-round and/or wear in taper limitation.
NOTE. . . Due to the choke specified for the cylinder barrel bore, a cam-controlled grinder is
required to regrind worn barrels to the maximum allowable 0.015 inch oversize dimension.
There should be little or no wear at the open end. Look for bent barrel fins and broken head
fins. Barrel fins can be straightened if not badly bent or cracked. Not more than a 10% total
reduction of head fin area is allowed. Look for cracked head fins, and specify repair of any
radial crack by drilling a vee notch to remove it. If a radial crack extends to the root of a
fin, it may have penetrated the wall; hence, the cylinder must be rejected.
If the cylinder base nuts were loose at disassembly, or if the base studs were loose or bent,
test the machined side of the cylinder flange for bending, which is cause for rejection.
Measure valve guides for wear, and look for scoring in their bores. Valve seats should be
inspected after refacing to make sure that their outside diameters are still less than the valve
head diameters. Exhaust valves should be checked for warpage before refacing, and all valves
should be measured in length if the stem tips were ground.
If there was any evidence of overheating of cylinder or piston, check for possible turning of the
head in relation to the barrel flange. Security between cylinder head and barrel is dependent
on metal to metal contact of cylinder barrel top threads within the head shoulder. Dark stains
at this area on both new and rebarreled cylinders is generally due to emission of thread
lubricant used at factory assembly of head to barrel.
Due to TSIO-360 engine series cylinder design, a persistent oil leak (not a sealing compound
leak) may indicate the required pre-load at the head/barrel junction has been relieved and must
be investigated for possible cylinder replacement (See TCM Service Bulletins M-87-8, M-69-7, or
current revisions as applicable).
I 72-40-09 HYDRAULIC VALVE LIFTERS. 100% Replacement at overahaul. During examination of each part,
look for sludge and carbon residues. Also check for obstructed oil holes. Inspect face of cam
follower on body for any type of damage and look for deep scoring and corrosion on exterior of
tubular portion. Discard any lifter body which exhibits any of these faults. To test roughly for
excessive diametrical clearance between hydraulic unit plunger and cylinder to check valve wear
in cylinder, start dry plunger into dry cylinder. While holding cylinder between thumb and
middle finger, depress plunger with index finger and release it quickly. compression of air in
cylinder should make plunger kick back instantly. If plunger does not return fully, either it is
excessively worn or check valve is leaking. To check for leaking valve, repeat compression test
while plugging end of oil inlet tube with other hand. If plunger still does not kick back
promptly, it and the cylinder are excessively worn. If it does kick back on the second test,
check valve seat is either worn, leaking, or dirty.
•
magnetos. One plugs fires with positive polarity, causing
excessive ground-electrode wear, while the next plug fires
negatively, causing excessive center electrode wear. To
equalize this, rotate as indicated in above figure 12-2.
5 3 1 CYLINDER ROTATION
CYLINDER CYLINDER
NUMBER NUMBER
FROM TO
1 TOP 6 BOTTOM
1 BOTTOM 6 TOP
2 TOP 5 BOTTOM
2 BOTTOM 5 TOP
3 TOP 4 BOTTOM
3 BOTTOM 4 TOP
4 TOP 3 BOTTOM
4 BOTTOM 3 TOP
5 TOP 2 BOTTOM
5 BOTTOM 2 TOP
6 TOP 1 BOTTOM
6 BOTTOM 1 TOP
6 4 2
FIGURE 72-40-13B. REVERSE SPARK PLUG PROCEDURE
72-40-08 REVISED OCT 97
72-40-14 EXHAUST SYSTEM. Before proceeding with cleaning and inspection, insure that the exhaust
system is cool. Inspection of the complete exhaust system is to be accomplished every 100
hours of operation and at overhaul. The entire exhaust system should be cleaned and visually
inspected for condition and leaks using the following procedure. Refer to Service Bulletins M-87-
14Rl, M-83-3, M-81-16, M-80-24, M-72-22, M-71-21 and M-67-12, or current revisions as
applicable.
A. Cleaning - in order to thoroughly inspect the exhaust system, components must be clean
and free -of oil, grease, etc. Use a suitable solvent (such as Stoddard solvent), apply by
spraying, allow solvent to drain and wipe dry with a clean cloth.
CAUTION. . . Never use highly flammable solvents, wire brushes or abrasives to clean exhaust
systems and never use a lead pencil to mark any exhaust system component.
B. Visual Inspection - Inspection procedures for 100 hour and overhaul intervals will be the
same, except that during overhaul the complete exhaust system (except turbochargers) will be
disassembled. During 100 hour inspection, items which might hinder inspection may be removed
except mUlti-segment 'V" band clamps. (See multi-segment "V" band clamp inspection procedure,
item "G").
C. Pressurized Exhaust System Inspection - Attach a 5 p.s.i. pressure source to the exhaust
tailpipe outlet (possibly a pressure/vacuum cleaner). The pressure source must be of high
volume, dUst free air to support exhaust system. After 5 p.s.i. is maintained in exhaust system,
apply soapy water over system and monitor for bubbles. If bubbles are noted, investigate.
D. Stack, Risers, Elbows - Inspect these components for burned areas, cracks and looseness.
During this inspection give special attention to the condition of welded areas and seams for
cracks.
E. Heater Muff - Special attention should be given in the pressurized exhaust system inspec-
tion. If air bubbles arise with the soapy water, replace heater muff.
F. Slip joints, Figure 72-40-14A - Visually inspect slip joints for bulging and cracks.
G. Multi-Segment "V" Band Clamps, Figure 72-40-14B - Clamps located between turbocharger
and tailpipe should first be cleaned using crocus cloth on the outer band of clamp assembly.
Inspect spot weld areas for cracks and looseness, inspect the corner radii of clamp inner
segments for cracks using a flashlight and mirror. If clamp has been removed and reinstalled,
inspect inner segment spacing. If inner segments contact after clamp assembly has been
torqued, the clamp assembly must be replaced. Inspect clamp outer band flatness using a
straightedge, especially within two inches of spot weld tabs that retain the "T" bolt fastener,
clearance should be less than .062 of an inch. Clearances in excess of .062 of an inch are cause
for rejection. Inner segment and outer band contact must be 100%.
NOTE. . . When replacement of clamp is required, install new clamp insuring "V" segments go
over exhaust flanges, using a rawhide or plastic mallet, tap clamp circumferentially as clamp is
torqued. Torque clamp nut 35-40 inch pounds. Safety wire clamp Figure 72-40-14B.
72-40-09
SLlPJOINT
SPOT
WELDS
35-40 in.-Ib.
INNER SEGMENTS
MUST NOT
CONTACT
AFTER
TORQUING -1---,,-_...\
_ INNER SEGMENT
OUTER BAND CONTACT
100%
72-40-10
72-40-15
INSPECTION CHART
Subassembly Special
And Part Inspect Nature Of Inspection Considerations
CYLINDER
ASSY.
Head & Barrel Head/Barrel Discoloration, Seepage. Clean, inspect. If seepage
Junction continues, replace cylinder.
Bore Diameters Wear in ring traversed area Refer to Table of Limits for
and step at top. Use dial- standard size bore or for
type gage set to zero near oversize bore.
open end of bore.
72-40-11
72-40-15. INSPECTION CHART (Continued).
Subassembly Special
And Part Inspect Nature Of Inspection Considerations
Base Flange If attaching nuts were found Allow not over 0.001 inch
loose at disassembly, test out-of-flat on machined
for flatness of mounting face. surface
Pushrod Housing
Stems Looseness, leakage.
Valve Length Use height gage to detect Stretched valves may fail.
stretch and check for re- Shortened valve may reduce
duction due to tip grinding. ability of hydraulic lifters
to take up lash.
CONNECTING
ROD
ASSEMBLY
Bushing Inside Diameter Measure using air gauge with New bushings must be reamed
correct size air plug and within diameter limits for
master setting ring. new parts. Sharp edges must
be broken slightly. (Refer
to Table of Limits, for wear
limits for new bushing and
new bushing alignment).
72-40-12
72-40-15. INSPECTION CHART (Continued).
Subassembly Special
And Part Inspect Nature Of Inspection Considerations
CRANKSHAFT
ASSEMBLY
Crankshaft Main Journals Diameters, scoring, burning. Must be polished before
magnetic inspection.
CAMSHAFT
ASSY.
Camshaft Journals Diameter and fit in crankcase Excessive bearing wear may
bearings. Scoring, pitting and be compensated by enlarging
corrosion. bearing and installing over-
size shaft. Refer to "Crank-
case".
Lobes Pitting along toe line, loss Serious pitting not permis-
of slope along toe line, sible. Toe line must taper
width across heel and toe at in relation to axis to rotate
center of length. valve lifters.
End and Rear Nicks, peening, other Must be smooth to align gear.
Face of Flange irregularities.
72-40-13
72-40-15. INSPECTION CHART (Continued).
Subassembly Special
And Part Inspect Nature Of Inspection Considerations
CRANKCASE
ASSY.
Crankcase Valve Lifter Diameter, Scoring.
Castings Guides
Oil Filler Neck Tightness Attempt to rock and pull out Must be tight in castings.
by hand only.
72-40-14
72-40-15. INSPECTION CHART (Continued).
Subassembly Special
And Part Inspect Nature Of Inspection Considerations
OIL COOLER
ASSY.
Oil Cooler Headers, Fins, Inspect visuallyfor dents,
Core deformed fins, punctures,
stripped plug hole threads,
cracks and scratches.
Oil Temp.
Control Valve Seat Roughness.
OIL SUMP
ASSY.
Casting Tapped Holes Damaged threads, cracks
around holes.
Mounting
Surfaces Scratches, warpage, cracks.
Engine
Mounting Machined Scratches, cracks.
Brackets Surfaces
ACCESSORY
CASE &
OIL PUMP
72-40-15
72-40-15. INSPECTION CHART (Continued).
Subassembly Special
And Part Inspect Nature Of Inspection Considerations
Gear Bushings Bore Diameters Use Telescoping gage and Refer to Table of Limits.
micrometer caliper.
Oil Pump Cover Shaft Holes Measure diameters. Refer to Table of Limits.
Tachometer Threads, Flange Thread distortion, warped See that old oil seal was
Drive Housing Seal Bore mounting surface, scored removed.
seal counterbore.
STARTER
ADAPTER
ASSEMBLY
Adapter All Areas Cracks, scratches on
machined surfaces, damaged
tapped holes.
72-40-16
72-40-15. INSPECTION CHART (Continued).
Subassembly Special
And Part Inspect Nature Of Inspection Considerations
INDUCTION
SYSTEM
Intake Manifold Flanges Check for warping by placing
flanges on surface plate.
Look for cracks.
72-40-17
72-40-15. INSPECTION CHART (Continued).
Subassembly Special
And Part Inspect Nature Of Inspection Considerations
FUEL
INJECTION
SYSTEM
Fuel Pump All Areas Cracks, damaged mounting
Adapter holes. Inspect tapped hole.
Measure bore diameter.
Fuel Injection
Control Assy.
Fuel Manifold
Valve Assy.
72-40-18
72-40-15. INSPECTION CHART (Continued).
Subassembly Special
And Part Inspect Nature Of Inspection Considerations
MAGNETO
DRIVE
ASSEMBLY
Gear Teeth Scoring, burring or wear
enough to alter tooth profile.
72-40-19
INTENTIONALLY
LEFT
BLANK
72-40-20
SECTION 72-50
ASSEMBLY OF SUBASSEMBLIES
72-50-01 General
72-50-08 Camshaft
72-50-09 Crankcase
72-50-01
INTENTIONALLY
LEFT
BLANK
72-50-02
72-50-00 ASSEMBLY OF SUBASSEMBLIES
72-50-01 GENERAL
NEW PARTS. Parts which require protection from atmospheric dust and moisture are wrapped
or boxed individually or in sets. These must not be unpacked until they are ready to be
installed. This includes precision bearing inserts and anti-friction bearings. Check other new
parts on receipt for transit damage. Refer to the parts catalog, Form X30S97A for part
number of the complete gasket set, the main bearing set, the piston ring set, and sealants and
lubricants, per Chapter 1. All of which must be on hand when work is started. Use only new
shake proof or split lockwashers, tab washers, elastic stop nuts, cotter pins and annealed,
corrosion-resistant lockwire.
TIGHTENING TORQUES. The accuracy of any torque indicating wrench depends on a smooth
application of force. Do not back up a nut or bolt and leave it in that condition. If part is
accidentally tightened too much, loosen it and retighten it to a value within the specified
limits. If a nut slot cannot be aligned with a cotter pin hole within the specified limits,
substitute another serviceable nut. If the cotter pin hole in stud lies beyond the nut slots
when the nut has been tightened properly, the stud has been improperly installed or has
backed out, or the attached part has been reduced in thickness, or either nut or washer is
incorrect part for that location. The situation must be corrected by whatever replacement is
indicated by inspection.
NOTE... Torque load valves are to be applied with the use of clean SOW oil.
72-50-03
TABLE OF TIGHTENING TORQUES FIGURE 72-50-01B.
THREAD TORQUE
SIZE IN.LBS. FT.lBS.
NOTE. . . Torque loads listed are for use with oil on threads. If cotter pin holes must be
aligned, set torque wrench at low limit and tighten nut to first hole beyond this torque,
except for connecting rods. Stud driving torques apply when studs are coated with lubricant
or sealer.
FINAL CLEANING. Immediately before assembling a group of parts, they should be washed in,
or sprayed with, a clean solvent and dried with dehydrated compressed air.
LUBRICATION. Immediately after final cleaning and before installation, coat all bare steel
surfaces and journals with clean engine lubricating oil, except where special lubricants are
mentioned in the text. In some instances where gears and other running parts are accessible
after assembly in a housing, additional oil should be applied to assure full coverage. Before
installing tapered pipe plugs or straight thread plugs, to prevent seizure and leakage of oil,
coat the male threads with anti-seize compound. Coat both sides of gaskets with lightweight
tight seal compound to assure a perfect seal and to counteract the permanent "set" caused by
compression.
A. Lubricate oil pump gears (4,5) with clean engine oil and install in oil cavity.
B. Insert oil pump drive gear (7) through top hole of oil pump cover (6). Carefully insert
shaft of drive gear into oil pump gear (4).
C. As gears are being rotated to insure free gear movement, push drive gear (7) and oil
pump cover inward until cover is squarely seated on oil pump cavity flange of accessory case.
D. Install screws (9) and tab washers (8). Turn screws in until snug and torque 75 to 85
inch pounds. Secure oil pump drive gear (7) using nut (10). Torque nut 280 to 300 inch
pounds. Check gears for freedom of rotation.
72-50-05
72-50-03 STARTER AND STARTER ADAPTER, TSIO-360-A, AB, D, DB OPTIONAL ON TSIO-
360-LB (See Figure 72-10-12A).
A. Install worm wheel gear (15) in shielded vise and assemble clutch spring (16) to worm
wheel gear. Secure spring (16) using bolt (18) and tab washer (17).
B. Assemble worm wheel gear (15), clutch spring (16) and bearing (14) to shaft gear
(19).
C. Install starter adapter housing (2) in shielded vise. Install shaft and clutch assembly
items (14 thru 19) into starter adapter housing (2) turning clockwise to seat clutch
spring (16).
D. USing an arbor press install new bushings (23,24,25) in accessory drive housing (22).
Install new oil seals (26, 27), gear (40), shaft (43) and secure using retaining ring (44).
Install new gaskets (45, 50), covers (46, 51) and secure using attaching hardware (47,
48, 49), (52 53, 54).
E. Install scavenge pump gears (30, 32) bushing (31) cover (33) and secure using bolt
(38) and tab washer (37). Install new o-ring (21) and accessory drive adapter (22) on
starter adapter housing. Secure using attaching hardware (34, 35, 36).
F. Install new needle bearing (7) into starter adapter housing. Press bearing (12) onto
worm shaft (8) until it is seated against flange. Install spring (9) woodruff key (10) and
worm gear (11). Insert assembly into adapter housing and secure using retaining ring
(13).
72-50-03 STARTER AND STARTER ADAPTER. TSIO-360-B, BB, C, CB, H, HB & JB (See
Figure 72-10-12B).
A. Install worm wheel gear (15) in shielded vise and assemble clutch spring (16) to worm
wheel gear. Secure spring (16) using bolt (18) and tab washer (17).
B. Assemble worm wheel gear (15) clutch spring (16) and bearing (14) to shaft gear (19).
C. Install starter adapter housing (2) in shielded vise. Install shaft and clutch assembly
items (14 thru 19) into starter adapter housing (2) turning clockwise to seat clutch
spring (16)
D. Install bushing (22), gears (25, 27), bushing (26) and cover (28) on cover (21) and
secure with attaching hardware (32, 33). Install new o-ring (20) and cover (21) on
starter adapter housing (2). Secure using attaching hardware (29, 30, 31). Install new
gasket (36), oil seal (23), cover (37) and secure using attaching hardware (38, 39, 40).
E. Install new needle bearing (7) into starter adapter nousing. Press bearing (12) onto
worm shaft (8) until it is seated against flange. Install spring (9) woodruff key (10) and
worm gear (11). Insert assembly into starter adapter housing and secure using
retaining ring (13).
72-50-03 STARTER AND STARTER ADAPTER, TSIO-360-E, EB, F, FB, GB, KB, MB, SB
A. Lay crankshaft (24) on bench with wooden support blocks under front and rear main
journals. Layout connecting rod assemblies (7 thru 13) opposite crankpins according to
position numbers stamped on bolt bosses. Install a new bearing insert (11) in each rod and
cap so their ends project equal distances. Lubricate and install each rod and cap with
position numbers on top when odd numbered rods are extended to the right and even num-
bered to the left. Secure rods and caps with rod bolts (9) and slotted nuts (8). Tighten nuts
to torque specified in Table of Tightening Torques (72-50-01 B) and install cotter pins (7).
B. Insert retaining plate and retaining ring with the flat or rough side of the retaining ring
to the outside. Install counterweight on crankshaft blade and insert correct pin. Pin is steel
stamped on end with a dash number. See parts catalog, Form X30597A for correct part
number. Secure counterweight with plate and retaining ring installed in same manner.
NOTE... Some 360 series engines use four (-41) pins and some use two (-43) and two (-44)
pins. Be sure that each counterweight has the same size pin.
C. Heat crankshaft gear (21) to 300°F., align gear dowel hole with crankshaft dowel and tap
gear onto shaft. Attach gear to shaft with four bolts (20). Tighten bolts to specified torque
and secure with lockwire.
D. Remove spring (5) from crankshaft oil seal assembly and unhook its ends. Coat the lip
of the seal with molyshield grease. Twist the seal and slide it over the crankshaft. Bring
the ends back together. Wrap the spring around the crankshaft in the seal area. Turn the
spring ends in an unwinding direction, then join and allow one end to wind into the other
end. With hooked ends opposite the seal split, lift the spring into the seal recess. Work the
remainder in by moving the fingers in both directions from the starting point. Make sure the
spring is in the deepest part of the recess all around.
B. Install gear (6) on camshaft and secure with four bolts (5). Tighten bolts to specified
torque and secure heads together with lockwire.
A. Replace any pipe plugs which may have been removed for cleaning and inspection of
galleries. Install new gaskets on machine thread plugs.
B. Spread a film of TCM Gasket Sealant on both sides of gasket (73) and install on
governor pad studs. Install cover (72) on governor pad and secure with four spacers (71), plain
washers (70), lockwashers (69), three nuts (61) and one bolt (68). Bolt (68) has been replaced
on current production engines by a stud and nut (61).
C. Install "0" rings (74, 75) and mounting legs (64, 65, 66, 67). Early TSIOjLTSI0-360-E,F
engines incorporate a spacer (92) between the crankcase and mount legs (65, 66) and a spacer
(91) between the crankcase and mount leg (67). On these engines, an "0" ring is installed on
both sides of the spacer. Secure mount legs with attaching parts (47, 48, 49). The turbo
mount bracket (93) is installed on the crankcase under mount leg (64). Secure with attaching
parts (61, 62, 63).
72-50-08
D. Turn both crankcase halves open side up. Make sure all squirt nozzles (85) are in
place. Lubricate all cam bearings and main bearings. Install intermediate and rear
main bearing inserts (1, Figure 72-10-17) and front main bearing inserts (2, Figure 72-
10-17). Insert bearings in seats so that edges project equally.
72-50-10 FUEL INJECTION (See Figure 72-50-10).
A. Other than installing fittings there will be no sub-assembly required for the fuel injection
systems except on the TSIO-360-MB & -SB. Fitting orientation charts are provided for
the manifold valves and fuel pumps.
B. On the TSIO-360-MB & -SB (See Figure 72-10-06B) install new gasket (36) and
controller (35) on throttle assembly (18). Secure using attaching hardware (37, 38,
39). Connect linkage assembly (12) to throttle (18) and controller (35) using attaching
hardware (13 thru 16). Install new O-ring (41) and overboost valve (40) on throttle
assembly using attaching hardware (42,43). Install fittings (Figure 72-50-100).
NOTE ... For adjustment of the controller, refer to the aircraft manufacturers instructions.
CAUTION. .. Use only fuel soluble thread lubricants on any fuel injection system
connection fittings.
'---B
D c D
D C
FIGURE 72-50-10A. FUEL MANIFOLD VALVE FITTING LOCATIONS
NOTES
CD These fittings are part of Fuel Injection Tube Assemblies See Figures 72-10-06A and B.
TSI0·360· 2024 X12935 X12935 628438 630119 EXT. 628437 628438 632555·12
E,EB,F,FB,G,G 636439 TEE 3050 CD MS20823·
B,H,HB,JB,KB 1320 3B
252 0
LfTSI0·360·E,
EB,KB
I
TSI0·360·LB 636349 X12935 X12935 628438 630119 EXT. 628437 MS20823·3B
®TSI0·360·MB 639494 CAP 636439 TEE 3050 252 0 632555·12
®TSI0·360·SB 1320
659494 CAP
90°
H 90°
90°
~, \l 180°
0°
A
IDLE CUTOFF
180° 180°
FIGURE 72-50-1oe. FUEL PUMP FITTING ORIENTATION
A FITTING BFiTTING CFITTING o FITTING EFITTING FFITTING GFITTING H
& ANGLE & ANGLE & ANGLE & ANGLE & ANGLE & ANGLE & ANGLE FITTING &
ANGLE
ENGINE FUEL INLET FUEL OUTLET VAPOR DECK SEAL DRAIN CONTROL DECK FUEL
RETURN PRESSURE PRESSURE RETURN
TSI0·360·A, 628475·0° 627119 628437·0° 2024 628438 632555·36 X5146·00 2024
AB,B,BB 828476·225°
TSI0·360·C,
CB,
TSI0·360·E, 628475·0° 627119 628437·0° 628436·310° 628436·0° 632555·43 2024 2024
EB,F,FB, KB 628436·310°
urSIO·360·G, 641249·175° 627119·310° 628437·90° 628439·310° 628436·0° 632555-43 2024 2024
GB, LB, MB, 628436·90°
I SB
TSI0·360· H, 628475-0° 627119 628437·0° 628436·310° 628436·0° 632555·36 2024 2024
HB,JB 628436·310°
-7'--T-t-- 0
o
oo ....w to
U1 oo
o
LEFT
BLANK
72-50-14
SECTION 72-60
FINAL ASSEMBLY
72-60-01 General
72-60-02 Crankcase
72-60-01
INTENTIONALLY
LEFT
BLANK
72-60-02
72-60-00 FINAL ASSEMBLY
72-60-01 GENERAL. Apply clean engine lubricating oil liberally to all bare steel surfaces, journals,
bearings and bushings, before and/or after installation, depending on accessibility, except
where special lubricants are mentioned.
(See Table of Tightening Torques and Instructions, Section 72-50-01A, B & C).
Wherever possible, measure clearances of running parts as they are installed. When end
clearances and backlashes cannot be measured with normal thickness gages due to the
inaccessible position of the parts, test for binding and excessive looseness possible by moving
the running parts.
Unless the atmosphere is unusually free of dust and airborne grit, it is advisable to cover
openings as soon as possible and to cover assemblies and the partial engine assembly whenever
they are not in the process of being assembled. Cover all openings into which small parts
might be dropped.
72-60-02 CRANKCASE (See Figure 72-10-06, 72-10-15, 72-10-17 & 72-60-02A thru D).
A. Attach mounting legs of left crankcase to engine assembly stand and support it as
shown in Figure 72-60-02A.
B. Lubricate all main bearing inserts and crankshaft journals. Install packing (4, Fig. 72-
10-17) in front main bearing. Lubricate both thrust washer halves with molyshield grease and
install.
C. Lift crankshaft assembly by No. 1 connecting rod and propeller flange while an assistant
holds No.'s 3 and 5 rods. Carefully lower the assembly into the crankcase bearing. Make
certain the oil seal enters the oil seal cavity. If properly installed, the connecting rod
pOSition numbers will be toward the upper crankcase flange.
D. Lubricate governor driven gear with clean engine lubricating oil and insert it into the
crankcase bore. Lay camshaft assembly in crankcase bearings, meshing spur gear teeth with
crankshaft gear so that timing marks are aligned and turning governor driven gear so it
meshes with governor drive gear (see Figure 72-60-02B).
E. With a feeler gauge, measure crankshaft and camshaft end clearance. See Table of
Limits, 72-30-08 for allowable tolerances.
F. Position starter shaft bushing (76, Figure 72-10-15) in place with dowel hole upward.
G. Spread a thin continuous film of No. 3 Aviation Permatex on the left crankcase parting
flange. Take care that the Permatex does not get on any other part. Lay lengths of No. 50
silk thread on parting flange. Thread should be on inside of bolt holes but never on the
flange edge (see Chapter 70 Standard Practices). Stand No.1, 3 and 5 rods upright being sure
that thrust washers have been installed and are properly seated. Carefully lower the right
crankcase onto the left crankcase.
Rotate the starter shaft bushing as necessary to align the hole with the dowel in the crank-
case.
72-60-03
H. Insert two thru bolts (45, Figure 72-10-15) through the crankcase halves at the nose, two
thru bolts (46) in front of No. 5 cylinder pad, one thru bolt (50) through lower corner of
front mount brackets, one thru bolt (51) at the lower corner of the rear mount brackets, four
thru bolts (52) through No. 3 and 5 cylinder mount pads, two thru bolts (56) below camshaft
level, one thru bolt (59) in lower hole of No. 1 cylinder pad and one thru bolt (60) in upper
hole of No. 1 cylinder mount pad. Tap all thru bolts to a centered position with a non-
marring hammer. These bolts align the crankcase castings and bearings.
72-60-04
FIGURE 72-60-028 ALIGNMENT OF TIMING MARKS
72-60-05
48 46 44 42 41 43 45 47 49 51 45 43 41 42 44 46 48
• • • • • • • • • 50
14 16 52
52
·
30b
•28 •
27 33b
• • • 22a •27 .39
39 • 8 15 8
40
•
29
• .
9
.
18 38
. .38 .18 .9 .29 .40
b. All studs and thru bolt threads are to be lubricated with oil grade 50, MHS 27, as
per Sealants and Lubricants Chart, Chapter 1-30-00.
ASSEMBLY PROCEDURE
I 3.
4.
Torque bolts and nuts to 50% of their specified torque following the sequence shown
in Figure 72-60-020, Torquing Sequence.
Apply final rated torque to all nuts and bolts following sequence shown.
440-460 . 2&3,5 thru 8,11 &12,14 thru 17,20&21,23 thru 28, 31 &32, 34 thru 37
275-325. .9,18,29,38
90-110 . . 39,40,52
J. Attach the manifold valve and bracket assembly (22 thru 25. 39 and 40). (Figure 72-10-
06) and lifting eye (30. Figure 72-10-15) to backbone and secure using spacers (27. 84)
washers (28). bolts (29). lockwashers (26) and nuts (25). Install throttle body bracket (24)
using attaching parts (18 thru 23). On TSIO 360 C & 0 engines. install bracket (90) in place
of bracket (24). Install bracket (90) on backbone. Install attaching parts (31 thru 34) in
remaining holes of upper parting flange. Attach right mount brackets to the overhaul stand
bed. Rotate stand to place engine in upright position.
K. Again check crankshaft and camshaft end play. this time using a dial indicator.
)
72-60-03 CYLINDERS AND PISTONS (See Figures 72-10-14 & 72-60-03).
A. Before installing each cylinder and piston, rotate crankshaft to place connecting rod in
its outermost position.
B. Dip piston pin in lubricating oil before installing piston on connecting rod. Lubricate all
cylinder head studs before installation of cylinder assemblies to crankcase. Lubricate piston
and rings liberally with engine lubricating oil.
C. Piston ring gaps should be positioned 1800 apart with the first or top ring gap toward
top of piston.
D. Install pistons and cylinders in desired order. It is suggested that Nos. 4 and 5 be
installed first to minimize turning of the crankshaft and to prevent excessive unbalance. Turn
the crankshaft for Nos. 2 and 3 and install the assemblies. Then turn the shaft for Nos. 1
and 6, and install the last two assemblies.
E. Place the piston over the connecting rod with the position number on its head forward.
Push the pin through until it is centered.
,'
72-60-08
FIGURE 72-S0-04. TORQUING THRU BOLTS
F. Hang a piston ring compressor on the piston skirt (Figure 72-60-Q3A). Holding the
cylinder in left arm, center the compressor over the piston rings and compress them fully.
Push the cylinder onto the piston, forcing the compressor off the piston.
G. Remove the ring compressor and start the cylinder base flange onto the holddown studs.
Make sure the base flange packing ring is in place and not twisted. Seat cylinder barrel
flange on crankcase cylinder pad. Install, but do not tighten, attaching parts (24) or (2S).
Top four nuts should be installed first, Figure 72-60-03B.
H. After installing all pistons and cylinders, tighten and torque nuts according to sequence
shown in Figure 72-60-02C, Torquing Sequence. For single cylinder installation refer to Figure
72-60-Q3C for torque sequence.
72-S0-04 ACCESSORY CASE (See Figure 72-10-07). Refer to Service Bulletin M-79-15, or current
revision as applicable.
A. Rotate engine stand to place engine in upright position. Apply a film of TCM gasket
sealant to crankcase side of accessory case gasket (7). Install gasket on crankcase studs.
B. Turning oil pump drive gear (7) of Figure 72-10-13 to mesh with square drive or cam
gear as applicable, install accessory case on crankcase studs.
C. Secure accessory case with attaching hardware (1 thru 6, Figure 72-10-07). Torque
hardware as per general use tightening torques Figure 72-S0-Q1A.
72-S0-09
D. Install new gasket (27), cover (26) or tach drive adapter (42, 43, 44) and secure with
attaching hardware (23, 24, 25). Install new gaskets (29, 34) and relief valve assembly (30
thru 36) or (28, 31, 32). Using new gaskets (19, 22) install screen (18) and plugs (21). Install
new gasket (17), o-ring (16), oil filter adapter (11), (12) or (13) as applicable, and secure
with attaching hardware (8, 9, 10) or install oil screen assembly (45 thru 48) as applicable.
For torque limits see Table of tightening torques 72-50-Q1A and general use tightening torques
72-50-01B.
A. Install new gasket (1), fuel pump (2) and secure with attaching hardware (32, 33, 34, or
35,36,37).
B. Insuring that all protective covers are removed, re-connect hoses to original locations.
A. Apply a thin coat of TCM Gasket Maker to the accessory case flange only.
NOTE. . . Turn gears by hand to be certain they mesh freely before installing sub-assembly on
accessory case mount pad.
B. Lubricate shaft gear and mesh it with crankshaft gear as adapter is pushed into position.
Seat adapter assembly against gasket. Secure using attaching hardware (59 thru 66) or (45
thru 51) or (49 thru 54) as applicable.
A. Install new o-ring (4) on shaft of alternator (2). Lubricate lip of new oil seal (5) and
the polished surface of the drive coupling hub with clean engine oil. Slide hub onto shaft,
over the woodruff key and through the seal lip until seated against inner race of ball bearing.
B. Install hub (6), retainer (8) and bushings (9). Slide gear (10) onto shaft so its drive lugs
are inserted in the rubber bushings.
C. When heavy duty coupling is used, only sleeve (12) is a serviceable item. Install
coupling assembly (11) with sleeve (12) in place.
D. Install nut (13) and tighten to 175 inch pounds torque. If necessary the nut may be
tightened further to align the cotter pin hole with the nut slots, but do not exceed 200 inch
pounds. Install cotter pin (14).
E. Install new gasket (1) on accessory case studs and install alternator (2). Secure with
attaching hardware (15) and (16).
72-60-10
72-60-08 OIL COOLER (See Figure 72-10-10).
A. Install new gasket (8) and oil cooler (7) on adapter (11). Secure using attaching
hardware (4, 5, 6).
B. Install new o-rings (12,13), new gaskets (14,17) plug (16) and oil temperature control
valve (15) into oil cooler adapter (11). Refer to torque tables 72-50-01 A & B for torque
limits.
72-60-09 VALVE MECHANISM (See Figure 72-60-10 and 72-10-14B)
A. Tum engine stand so engine is in the inverted position. Lubricate exterior surface of
cam lobes and each hydraulic valve lifter face with Dow Coming® Molykote G-n paste
just prior to installation. Apply oil to socket but not into body oil holes. Install all valve
lifters.
I
B. Install o-ring (17) on cylinder end of pushrod housing (21). Compress spring (20) and
install retaining cage, 72-10-14B, insert crankcase end of pushrod housing into spring
install one washer (18), packing (19) and washer (18). Insert spring loaded end of
housing into crankcase bore and align opposite end with cylinder head flange hole.
Remove spring compressor cage and allow housing to snap into place.
C. Insert push rods (16) into cylinder housing and tum crankshaft until both pushrods are
in their lowest position. Lubricate rocker shafts (11) with clean lubricating oil and insert
in rocker assembly (13,14,15). Install thrust washers (12). Install rocker and shaft on
cylinder rocker studs. Be sure that thrust washers tum freely. Install retainers (10) on
both ends of shaft (11). Secure shaft using attaching hardware (8, 9). After tightening
nuts bend ears of tab washers up against flat of nuts. Install pushrods and rockers on
remaining cylinders in same manner. Check valve rocker toe to valve stem clearance
per table of limits Figure 7230-08 with lifter flat.
D. Coat cover side of gasket (7) with TCM gasket sealant. Install gaskets and covers (4,
5). Cover (5) is used on cylinder number (2) next to the oil cooler. Oil cooler support
shoe should be installed. Secure using attaching hardware (1, 2, 3).
E. Apply a light film of Loctite pipe sealant to pipe threads of nipples (44) and install in
cylinder intake chamber drain hole. Install cylinder drain manifold (22) on each bank
of cylinders.
72-60-10 INTERCYLINDER AIR BAFFLES LlTSIO 360 E, EB, KB, TSIO E, F, FB, GB, KB. LB,
MB & SB (See Figure 72-10-14A).
A. Install baffles (8, 9,12) and secure to support (5) loosely with washer (16) and screw
I
(4).
B. Install baffle assemblies (14, 15) and secure loosely with spacer (2), brackets (1, 7),
washers (16) and bolts (6).
C. Install intercylinder baffles (13) and install support (3). Secure with spring and fastener
(10,11).
D. Make certain that all interconnecting baffle grooves are in place and tighten bolts (6)
and screws (4). Install fuel line brackets (17).
72-60-12
72-S0-11 OIL SUMP (See Figure 72-10-09).
A. Make certain that suction tube (6) is firmly installed in oil sump (8). Rotate engine
stand to place engine in inverted position. Apply a film of rCM gasket maker to sump side of
gasket (7) and lay gasket in position on the crankcase to sump parting flange.
B. Install sump (8) on crankcase studs and secure using attaching hardware (3, 4, 5). Care
should be taken to assure a good seal at oil passage in left hand rear corner of sump. Install
new gasket (2) and plug (1).
72-S0-12A INDUCTION SYSTEM TSI0-3So-A, AB, B, BB, H, HB & JB (See Figure 72-10-08A).
A. Install riser and elbow riser assemblies (2 thru 6) using new gaskets (1). Loosely install
attaching hardware (7, 8, 9). Install throttle assembly and secure to engine using attaching
hardware (14,15).
B. Slide clamps (10) onto riser assemblies and install hoses (12). Do not tighten clamps at
this time.
C. Make sure riser assemblies are squarely seated on cylinder intake flanges, tighten
hardware (7, 8, 9), center hoses (12) and secure with clamps (10).
D. Install new gasket (20) and throttle adapter (21) on throttle assembly (13). Secure with
attaching hardware (23, 24, 25). Install fittings (26, 27, 35), hose (36) and air reference lines
(16, 18,28) using new seals (19).
E. Install injector nozzles (30 figure 72-10-06A) and sleeve assemblies 31, using new seals
(32), washers (33), (34).
A. Install riser and elbow riser assemblies (2 thru 6) using new gaskets (1). Loosely install
attaching hardware (7, 8, 9). Install throttle assembly and secure to engine using attaching
hardware (15, 16).
B. Slide clamps (10) onto riser assemblies and install hoses (12). Do not tighten clamps at
this time.
C. Make sure riser assemblies are squarely seated on cylinder intake flanges and tighten
hardware (7, 8, 9). Center hoses (12) and secure with clamps (10).
D. Install new gasket (17) and throttle adapter (18) on throttle assembly (14). Secure with
attaching hardware (19 thru 22). Secure throttle adapter (18) to engine using attaching
hardware (15,16).
E. Install fitting (38) and hose (39) into throttle adapter (14). Install air reference lines
(25, 26, 27) using new seals (28, 30). Attach air reference line (27) to engine using bracket
and attaching hardware (23, 24, 35, 36, 37). Install injector nozzles (30) Figure 72-10-06A and
sleeve assemblies (31) with new washers (33, 34) and seals (32).
72-S0-12C INDUCTION SYSTEM TSI0-3So-E, EB, F, FB, LTSIO 3S0 E, EB (See Figure 72-10-08C).
A. Install riser and elbow riser assemblies (2 thru 6) using new gaskets (1). Loosely install
attaching hardware (7, 8, 9). Install throttle assembly and secure to engine using attaching
hardware (14, 15).
72-S0-13
B. Slide clamps (10) onto riser assemblies and install hoses (12). Do not tighten clamps at
this time.
C. Make sure riser assemblies are squarely seated on cylinder intake flanges and tighten
hardware (7, 8, 9). Center hoses (12) and secure with clamps (10).
D. Using hoses (26), clamps (25), connect induction tubes (27, 28) to throttle adapter (36)
and throttle adapter (36) to throttle assembly (13) using new gasket (40) and attaching
hardware (8, 9, 37, 88). Install overboost valve (30) using new o-ring (29) onto induction
tube (28).
E. Install fittings (39) and air reference lines (16, 18, 20) into air throttle adapter (36)
using new seals (17, 19). Install injector nozzles (30) Figure 72-10-06A and sleeve assemblies
(21) using new washers (23, 24) and seals (22). Install fitting (34) and hose (35) into throttle
assembly.
A. Install riser and elbow riser assemblies (2 thru 6) using new gaskets (1). Loosely install
attaching hardware (7, 8, 9). Install throttle assembly and secure to engine using attaching
hardware (14, 15).
B. Slide clamps (10) onto riser assemblies and install hoses (12). Do not tighten clamps at
this time.
C. Make sure riser assemblies are squarely seated on cylinder intake flanges and tighten
hardware (7, 8, 9). Center hoses (12) and secure with clamps (10).
D. Using hoses (26), clamps (25, 35), connect induction tubes (27, 28) to throttle adapter
(36) and throttle adapter (36) to throttle assembly (13) using new gasket (40) and attaching
hardware (8, 9, 37, 38). Install overboost valve (30) using new o-ring (29) onto induction tube
(28).
E. Install fittings (39) and air reference lines (16, 18, 20) into air throttle adapter (36)
using new seals (17, 19). Install injector nozzles (30) Figure 72-10-06A and sleeve assemblies
(21) using new washers (23, 24), seals (22). Install fitting (34) and hose (35) into throttle
assembly.
A. Install riser and elbow riser assemblies (2 thru 6) using new gaskets (1). Loosely install
attaching hardware (7, 8, 9). Install throttle assembly and secure to engine using attaching
hardware (14, 15).
B. Slide clamps (10, 11) onto riser assemblies and install hoses (12). Do not tighten clamps
at this time.
C. Make sure riser assemblies are squarely seated on cylinder intake flanges and tighten
hardware (7, 8, 9). Center hoses (12) and secure with clamps (10, 11).
D. Using hoses (26) and clamps (25, 35), connect induction tubes (27, 28) to throttle adapter
(36) and throttle adapter (36) to throttle assembly (13) using new gasket (40) and attaching
hardware (8, 9, 37, 38). Install overboost valve (30) using new o-ring (29) onto induction tube
(28).
72-60-14
E. Install fittings (39), air reference lines (16, 18, 20) into air throttle adapter (36) using
new seals (17, 19). Install injector nozzles (30) Figure 72-10-06A and sleeve
assemblies (21) using new washers (23, 24), seals (22). Install fitting (34) and hose
(35) into throttle assembly.
72-60-12F INDUCTION SYSTEM TSIO-360-M8, S8 (See Figure 72-10·08F). I
A. Install throttle assembly on engine using attaching hardware and brackets (36 thru 40).
Using new gasket (22) attach induction manifold (14) to throttle assembly. Secure with
attaching hardware (23, 24).
B. Loosely assemble induction tubes (2 thru 7) to cylinder assemblies with flanges and
attaching parts (8 thru 11). Install hoses (13) and secure with clamps (12). Tighten
nuts (11) securing flanges (8) and tubes (2 thru 7).
C. Install induction tubes (19, 33) and aftercooler (20). Secure with hoses and clamps
(18) and (35). Install air reference lines (21, 29, 31) with new seals (30). Install
injector nozzles (20) Figure 72-10-068 and sleeve assemblies (25) with new washers
(27, 28), seals (26).
72·60-13AFUEL INJECTION (See Figure 72-10-06A).
A. Fuel injector nozzles and air reference sleeves were installed during induction system
assembly.
B. Install manifold valve assembly (28) on engine using bracket (40) and attaching
hardware (22, 231 24, 25, 39).
C. Connect fuel discharge tubes (29) to manifold valve and injector nozzles. Install fuel
hoses (34) and (41).
72-60-138 FUEL INJECTION TSIO 360 M8 & S8 (See Figure 72-10-068). I
A. Fuel injector nozzles and air reference sleeves were installed during induction system
assembly.
B. Install manifold valve (44) on engine using bracket (46) and attaching hardware (47
thru 53)
C. Connect fuel discharge tubes (19) to manifold valve and injector nozzles. Secure fuel
discharge tubes using brackets (27,28) and attaching parts (29, 30, 31).
D. Install fuel hoses (22, 23, 24).
72-60-14 IGNITION SYSTEM (See Figure 72-10-05).
NOTE. .. Timing marks for the LlTSIO are on the outer edge of the crankshaft propeller
flange, and for all others on the outer edge of the crankshaft counterweight blade between
cylinders 2 and 4. The inspection plug between cylinders 2 and 4 on the left top side of
the crankcase must be removed to view the marks on the crankshaft.
A. Plug one spark plug hole of No. 1 cylinder and place a thumb over the other plug hole.
Have a second person stand at the front of the engine and turn the crankshaft
counterclockwise (clockwise for LTSIO engines) until pressure is felt on the thumb. No.
1 piston is coming up on the compression stroke. To time the LffSIO, hold a
machinist square so its base is along the crankcase vertical parting line above the
crankshaft and the arm of the square is pointing outward past the crankshaft propeller
flange. Turn the crankshaft
B. Remove inspection hole plug from magneto. Turn magneto coupling until painted
chamfered tooth on the distributor gear is approximately centered in the inspection hole.
Hold magneto in its approximate installed position. Note carefully the position of the coupling
drive lugs.
C. Lubricate the gear support shaft with clean lubricating oil, and install drive gear
assembly (35 thru 3S), so the slots of the drive bushings will be in the approximate position
for aligning with drive coupling lugs. Insert retainer (34) into gear hub slot. Apply a film of
Molyshield grease to each of the new rubber bushings (33). Insert the bushings into the
retainers, rounded long edges first.
D. Place a new gasket (S) on flange of magneto. Install magneto carefully so drive
coupling lugs mate with slots of drive bushings. Install and snug down but do not tighten,
two sets of attaching parts (6, 5, 4).
E. Install the ignition harness assemblies. Secure each outlet plate (26) with four sets of
attaching parts (3, 2).
F. Connect a timing light lead to the magneto ground terminal (or according to manufac-
turer's instructions). Tap magneto case with a non-marring hammer, counterclockwise (from
the rear) to make certain the points are closed. After timing light indicates points are
closed, tap the magneto lightly clockwise (counterclockwise for LTSIO) until the points are
open. Tighten magneto attaching nuts. Install magneto pressurization lines (TSIO-360GB4,
LB6 & MB).
G. Check timing by backing up crankshaft approximately five degrees and tapping gently
forward until timing light indicates opening breaker points. If timing is correct, the points
will open at the 20 degree mark (midway between the 16 and 24 stamped on the crankshaft).
The crankshaft has marks in two degree increments with 16 and 24 at each extreme.
H. Apply BG mica thread lubricant to first three threads of spark plugs (1). Install plugs
and gaskets in cylinders. Insert ignition cable terminals into plugs and screw cable coupling
nuts onto plugs. Make certain conduits are not kinked or interfering with some other part.
Attach brackets and tighten all coupling nuts. mEl mil PlUes
10-----------'
lO1it1 sm, pucs
72-60-18
SECTION 72-70
TESTING AFTER OVERHAUL
72-70-01
INTENTIONALLY
LEFT
BLANK
72-70-02
72-70-00 TESTING AFTER OVERHAUL.
72-70-01 TEST STAND. After each major overhaul, engine performance should be tested and new parts
run-in while the engine is mounted on a rigid test stand, enclosed in a cell of such design
that recirculating air is held to a minimum. The engine stand should be constructed in a way
to permit accessibility to all engine lines and instrument connections and to permit frequent
inspection of all points of possible leakage. All tubes, wires, rods and cables used to connect
instruments and controls should be well supported, and of sufficient flexibility to permit them
to be moved out of the way during installation and removal of the engine.
NOTE . . . When necessary, the airframe can be considered a suitable test stand for running
in overhauled engines. Refer to Service Bulletin M88-7 or current revision as applicable.
72-70-02 TEST CLUB. Unless a dynamometer is used to apply controlled loads to the crankshaft, it
will be necessary to install a wood test club such as those supplied by the Hartzell Propeller
Fan Co., Piqua, Ohio. Test clubs are supplied in standard diameters and must be customized as
required. After customizing they should be calibrated with a torque meter.
72-70-03 COOLING AIR SCOOP. The scoop must be designed to fit over the tops of all cylinders, with
padded seals for rear cylinders and valve rocker covers, to direct an adequate flow of air
downward through the cylinder fins. Vanes are necessary to direct cooling air to the center
cylinder and the oil cooler. CHT should not vary more than 50°F. between coolest and hottest
cylinders. Provide an air duct to the alternator vent tube.
72-70-04 INDUCTION AIR INTAKE. An air filter and housing should be attached to the inlet flange.
The filter area must be sufficient to avoid restriction of air flow. Always clean filter before
each test.
72-70-05 EXHAUST SYSTEM. For testing purposes the exhaust system supplied by the airframe
manufacturer should be installed.
72-70-06 CONTROLS. The only controls required are a mixture control and throttle control capable of
operating the fuel control and metering shafts through their complete ranges, and a standard
twin magneto switch connected to the magneto ground terminals.
72-70-07 ELECTRICAL WIRING. A storage battery must be connected by a No. 0 stranded copper cable
from its positive terminal to the power terminal of the starter or starter solenoid. The battery
negative terminal must be connected to the engine or both battery terminal and engine may be
grounded. A small insulated wire should connect the starter solenoid coil terminal to a 5
ampere pushbutton switch. The other switch terminal must be connected to the engine or both
to common ground.
72-70-08 INSTRUMENTS. The control panel should be equipped with the following calibrated engine
.instruments:
A. A mechanically driven (counterclockwise, 1/2 engine RPM) tachometer and flexible shaft
assembly is required.
D. A cylinder head temperature gage and wiring to each cylinder. (See test operating
limitations for different maximum temperatures).
72-70-03
E. A water manometer with rubber hose connection to the vacuum pump oil return hole at
the rear of the crankcase.
72-70-09 BREATHER. A substantial hose of 3/4 inch 10 should be securely clamped over crankcase
breather elbow and support so as to lead to a point above and to the rear of engine.
72·70-10 FUEL SYSTEM. The test stand fuel system is to incorporate an auxiliary pump capable of
delivering fuel to and through engine system at a pressure of 2.5 to 4.0 p.s.i. indication on
fuel pressure gage. Means of determining, by weight, fuel consumption for given periods of
time and a specific percentage of power should also be included. Connect stand fuel supply
line to upper elbow projecting from left side of fuel pump shroud. Connect fuel pump-to-
supply tank return line to upper elbow projecting from right side of fuel pump. Connect fuel
pressure gage line to the fitting projecting from the center rear of fuel manifold valve.
72-70-11 GOVERNOR PAD COVER. A removable oil transfer tube conducts oil under pressure from the
front main bearing through the crankshaft to the propeller hub. Crankshafts are equipped with
an oil transfer collar to supply the governor controlled oil to the crankshaft for use with an
oil controlled propeller. When a test club or fixed pitch propeller is used for testing purposes,
the governor pad cover must have an internal grooved surface to allow the circulating oil to
lubricate the oil transfer collar. The governor pad cover is not needed if a propeller governor
is installed.
72-70-12 ENGINE TEST. (See Test Schedule 72-70-14) Refer to Service Bulletins M-88-7, M-87-20 and
M-87-9, or current revisions as applicable.
A. Make one check on performance of each magneto alone at 2100 RPM. Clear spark plugs by
operating with both magnetos on for a few seconds between checks.
B. Take instrument readings at the beginning, in the middle, and at the end of the full
throttle period. Take one reading during each of the other periods as soon as conditions have
stabilized.
NOTE . . . The maximum allowable cylinder head temperature and the maximum allowable oil
temperature must not be exceeded at any time during the test.
C. Extend the second period of each test schedule, if necessary, to raise the oil temperature
to 100°.
O. Run the engine according to the schedule in this section after a major overhaul. (Standard
Acceptance Test).
72-70-04
72-70-13 STARTING PROCEDURE.
c. Press boost pump button and hold it until 2.5-3.0 or 4.0 p.s.i. nozzle pressure depending
on type pump used is obtained; then release boost pump button and press starter button.
NOTE . . . During operation of the starter, the boost pump may be used intermittently to
maintain 2.5 to 3.0 or 4.0 p.s.i. nozzle pressure depending on type pump used. DO NOT use
boost pump after engine is running smoothly.
72-70-05
72-70-14
OVERHAUL TEST RUN
STANDARD ACCEPTANCE TEST
1 5 1200
2 5 1600
3 10 2450
4 15 CD ® Rated RPM
5 10 ® ® ® Engine Parameter Checks
6 10 2450
7 5 ® Idle RPM 600.±. 25
8 15 ® 2450
9 15 @ 2450
90 TOTAL MINUTES
® Check Fuel System, Oil Pressure, Oil Temperature, M.A.P., C.H.T. and Alternator.
@ Magneto drop and spread to be taken at 2100 RPM. Engine must be throttled to specified RPM
and temperature allowed to settle out before taking magneto drop and spread.
® Cooling Period - 3000 Max. C.H.T. Before Shut-Down, Recheck Idle Adjustments.
® Runs 8 And 9 Must Be Made With Stops For Leak Checks At The End Of Each Run. The
engine will not be accepted until two successive 15 minute runs are made with no leaks.
72-70-06
72-70-14
OIL CONSUMPTION DETERMINATION
1 5 1200
2 5 1600
3 5 2450
4 10 (j) ® Rated RPM
5 10 <D ® @) Engine Parameter Checks
6 5 ® Idle RPM 600 .±. 25
Stop engine, drain oil, weigh oil in for oil consumption determination.
® Adjust engine - fuel flow and pressure (Reduce RPM for adjustments).
® Check fuel injection, oil pressure, oil temperature, MAP., C.H.T. and alternator.
@) Magneto drop and spread to be taken at 2100 RPM. Engine must be throttled to specified RPM
and temperature allowed to settle out before taking magneto drop and spread.
® Readings must be recorded after completion of each 10 minute interval during run.
® Cooling period 3000 Max. C.H.T. before shut-down, recheck idle adjustments.
72-70-07
72-70-14 OVERHAUL TEST RUN TEST OPERATING LIMITS
ENGINE MODEL RATED MAX. CONT. BHP REC. MAX CRUISE BHP
Oil Pressure
Idle, Minimum psi, (All Models) ................................................................................ '" ...... 10
Normal Operation, psi (TSIO-360- A,AB,B,BB,C,CB,D,DB,H,HB,JB) ..................... 30 to 60
Normal Operation, psi (TSIO-360- E,EB,F,FB,G,GB,KB,LB,MB,SB) ...................... 30 to BO •
Oil Temperature
Minimum for Take-Off ............................................................................... All Models 100° F
Maximum Allowable ......................................................................................... 11 0°C/240°F
Recommended Cruising ................................................................... 71 o-B2°C/160°F-1BO°F
Ambient air and engine operating temperatures are of major concern during this test flight.
Do a normal pre-flight run-up in accordance with the aircraft flight manual. Conduct a
normal take-off with full power and monitor the fuel flow, RPM, oil pressure, cylinder head
temperatures and oil temperatures. Reduce to climb power in accordance with the flight
manual and maintain a shallow climb attitude to gain optimum airspeed and cooling. Rich
mixture for all operations except lean for field elevation where applicable and lean to maintain
smoothness during climb in accordance with airframe manufacturer's operating instructions.
Level flight cruise should be at 75% power with best power or richer mixture for the first
hour of operation. The second hour power settings should alternate between 65% and 75%
power with the appropriate best power mixture settings. Engine controls or aircraft attitude
should be adjusted as required to maintain engine instrumentation within specifications.
Descent from high altitude should be accomplished at cruise power settings, with the mixture
control positioned accordingly.
CAUTION . .. Rapid descents at high RPM and idle manifold pressure are to be avoided.
During descent, monitor cylinder head and oil temperatures, maintaining above the minimum
specified limits.
NOTE ... Avoid long descents at low manifold pressure, which can result in excessive engine
cooling. Satisfactory engine acceleration may not occur when power is applied. If power must
be reduced for long periods, adjust propeller to minimum governing RPM and set manifold
pressure no lower than necessary to obtain desired performance. If the outside air is ex-
tremely cold, it may be desirable to add drag (gear, flaps) to the aircraft in order to maintain
engine power without gaining excess airspeed. Do not permit cylinder temperature to drop
below 300°F. for periods exceeding five (5) minutes.
Any discrepancies detected during test flight or any final adjustments necessary should now be
made. The engine can be operated in normal service in accordance with the aircraft flight
manual.
72-70-10
SECTION 72-80
ENGINE PRESERVATION
72-80-01 General
72-80-02 Flyable Storage
72-80-03 Temporary Storage
7,2-80-04 Indefinite Storage
72-80-01
INTENTIONALLY
LEFT
BLANK
72-80-02
72-80-01 GENERAL.
Refer to Service Bulletin M-84-10R1, or current revision as applicable.
Engines in aircraft that are flown only occasionally tend to exhibit cylinder wall corrosion
more than engines in aircraft that are flown frequently.
Of particular concern are new engines or engines with new or freshly honed cylinders after a
top or major overhaul. In areas of high humidity, there have been instances where corrosion
has been found in such cylinders after an inactive period of only a few days. When cylinders
have been operated for approximately 50 hours, the varnish deposited on the cylinder walls
offers some protection against corrosion. Hence a two step program for flyable storage
category is recommended.
Obviously, even then proper steps must be taken on engines used infrequently to lessen the
possibility of corrosion. This is especially true if the aircraft is based near the sea coast or in
areas of high humidity and flown less than once a week.
In all geographical areas the best method of preventing corrosion of the cylinders and other
internal parts of the engine, is to fly the aircraft at least once a week, long enough to reach
normal operating temperatures, which will vaporize moisture and other by-products of com-
bustion. In consideration of the circumstances mentioned, TeM has listed three reasonable
minimum preservation procedures, that ~ implemented, will minimize the detriments of rust
and corrosion. It is the owner's responsibility to choose a program that is viable to the
particular aircraft's mission.
Aircraft engine storage recommendations are broken down into the following categories:
Program" Engines or cylinders with more than 50 operating hours to TBO if not
flown weekly:
a. Propeller pull thru every 7 days as per paragraph 2; and
b. Fly every 30 days as per paragraph 3.
2. The propeller should be rotated by hand without running the engine. For 4 and 6
cylinder straight drive engines. rotate the engine six revolutions. Stop the propeller 45°
to 90° from the original position. For 6 cylinder geared engines, rotate the propeller 4
revolutions and stop the propeller 30° to 60° from the original position.
72-80-03
CAUTION . .. FOR MAXIMUM SAFETY, ACCOMPLISH ENGINE ROTATION AS FOLLOWS:
3. The aircraft should be flown for thirty (30) minutes, reaching, but not exceeding, normal
oil and cylinder temperatures. If the aircraft cannot be flown it should be represerved in
accordance with "8" (Temporary Storage) or "C" (Indefinite Storage). Ground running is
not an acceptable substitute for flying.
It is necessary that for future reference, if required, the propeller pull thru and flight
time be recorded and verified in the engine maintenance record/log with the date, time
and signature.
a. Remove the top spark plug and spray preservative oil (Lubrication Oil - Contact and
Volatile Corrosion - Inhibited, MIL-L-46002, Grade 1) at room temperature, through
upper spark plug hole of each cylinder with the piston in approximately the bottom
dead center position. Rotate crankshaft as each pair of opposite cylinders is
sprayed. Stop crankshaft with no piston at top dead center. A pressure pot or
pump-up type garden pressure sprayer may be used. The spray head should have
ports around the circumference to allow complete coverage of the cylinder walls.
NOTE ... Shown below are some approved preservative oils recommended for use
in Teledyne Continental engines for temporary and indefinite storage.
b. Re-spray each cylinder without rotating crank. To thoroughly cover all surfaces of
the cylinder interior, move the nozzle or spray gun from the top to the bottom of
the cylinder.
d. Apply preservative to engine interior by spraying the above specified oil (approxi-
mately two ounces) through the oil filler tube.
e. Seal all engine openings exposed to the atmosphere using suitable plugs, or moisture
resistant tape, and attach red streamers at each point.
72-80-04
f. Engines, with propellers installed, that are preserved for storage in accordance with
this section should have a tag affixed to the propeller in a conspicuous place with
the following notation on the tag: "00 NOT TURN PROPELLER - ENGINE
PRESERVED." PRESERVATION DATE _ _ _ _ _ _ _ _ __
b. With bottom spark plugs removed from the cylinders, hand turn propeller several
revolutions to clear excess preservative oil, then re-install spark plugs.
d. Give the aircraft a thorough cleaning and visual inspection. A test flight is recom-
mended.
a. Drain the engine oil and refill with MIL-C-6529 Type II. The aircraft should be
flown for thirty (30) minutes, reaching, but not exceeding normal oil and tempera-
tures. Allow engine to cool to ambient temperature. Accomplish steps "1.a." and
"1.b." of Temporary Storage.
2. Install dehydrator plugs MS27215-1 or -2, in each of the top spark plug holes, making
sure that each plug is blue in color when installed. Protect and support the spark plug
leads with AN-4060 protectors.
4. If the carburetor is removed from the engine, place a bag of desiccant in the throat of
the carburetor air adapter. Seal the adapter with moisture-resistant paper and tape on a
cover plate.
72-80-05
5. The TCM fuel injection system does not require any special preservation preparation. For
preservation of the Bendix RSA-7DA1 fuel injection system, refer to the Bendix Opera-
tion and Service Manual. Not applicable for 0-470 Model engines.
6. Place a bag of desiccant in the exhaust pipes and seal the openings with moisture-
resistant tape.
7. Seal the cold air inlet to the heater muff with moisture-resistant tape to exclude
moisture and foreign objects.
8. Seal the engine breather by inserting a dehydrator MS27215-2 plug in the breather hose
and clamping in place.
9. Attach a red streamer to each place on the engine where bags of desiccant are placed.
Either attach red streamers outside of the sealed area with tape or to the inside of the
sealed area with safety wire to prevent wicking of moisture into the sealed area.
10. Engines, with propellers installed, that are preserved for storage in accordance with this
section should have each propeller tagged in a conspicuous place with the following
notation on the tag: "DO NOT TURN PROPELLER - ENGINE PRESERVED." PRESERVA-
TION DATE _ _ _ _ _ _ _ _ _ _,
1. Remove the cylinder dehydrator plugs and all paper, tape, desiccant bags, and streamers
used to preserve the engine.
2. Drain the corrosion preventive mixture and re-service with recommended lubricating oil.
WARNING ••• When returning the aircraft to service do not use the corrosion preven-
tive oil referenced in paragraph C.1.a. for more than 25 hours.
3. If the carburetor has been preserved with oil, drain it by removing the drain and vapor
vent plugs from the regulator and fuel control unit. With the mixture control in "Rich"
position, inject service type gasoline into the fuel inlet at a pressure not to exceed 10
p.s.i. until all of the oil is flushed from the carburetor. Re-install the carburetor plugs
and attach the fuel line.
4. With bottom plugs removed, rotate propeller to clear excess preservative oil from
cylinders.
5. Re-install the spark plugs and rotate the propeller by hand through the compression
strokes of all the cylinders to check for possible liquid lock. Start the engine in the
normal manner.
6. Give the aircraft a thorough cleaning, visual inspection and test flight per airframe
manufacturer's instructions.
1. Aircraft prepared for indefinite storage should have the cylinder dehydrator plugs visually
inspected every 15 days. The plugs should be changed as soon as their color indicates
unsafe conditions of storage. If the dehydrator plugs have changed color in one-half or
more of the cylinders, all desiccant material on the engine should be replaced.
72-80-06
2. The cylinder bores of all engines prepared for indefinite storage should be re-sprayed
with corrosion preventive mixture every six months, or more frequently if bore inspection
indicates corrosion has started earlier than six months. Replace all desiccant and
dehydrator plugs. Before spraying, the engine should be inspected for corrosion as
follows: Inspect the interior of at least one cylinder on each engine through the spark
plug hole. If cylinder shows start of rust, spray cylinder corrosion preventive oil and
turn prop over six times, then re-spray all cylinders. Remove at least one rocker box
cover from each engine and inspect the valve mechanism.
The above procedures are a general recommendation for our customers. Since local conditions
are different and Teledyne Continental Motors has no control over the application, more
stringent procedures may be required. Rust and corrosion prevention are the owner's responsi-
bility.
12-80-01
INTENTIONALLY
LEFT
BLANK
72-80-08
CHAPTER 73
ENGINE FUEL SYSTEM
73-00-01
INTENTIONALLY
LEFT
BLANK
73-00-02
73-00-00 ENGINE FUEL SYSTEM
The fuel injection system is of the multi-nozzle, continuous-flow type which controls fuel
flow to match engine requirements. Any change in air throttle position, engine speed, deck
pressure, or a combination of these causes changes in fuel pressure in the correct relation to
the engine requirements. As fuel flow is directly proportional to metered fuel pressure,
settings can be predetermined and fuel consumption can be accurately predicted and controlled.
The continuous-flow system permits the use of a typical rotary vane pump with integral relief
valve. With this system there is no need for an intricate mechanism for timing injection to
the engine.
The fuel injector pump is equipped with a vapor separator where the vapor is separated by a
swirling and augmentor system from the fuel and returned to the tank. The fuel injector
pump forces solid fuel into the metering unit assembly.
The fuel metering unit/air throttle controls the amount of intake air admitted into the intake
manifold and meters the proportionate amount of fuel to the manifold valve. The assembly
has two control units; one for air in the air throttle assembly, and one for the fuel control
unit.
,II
', ; CHECK
VALVE:
' , / ' , FUEL PR. A.DJUSTMENT
~I
;
G
,
L -_ _ rO'NCREAS£
, I II ,~LFl/!'!
~~;F,-LJ1* ; , •
VAPOR SEPARATOR
:1 ~~'~ _Iih~r
I
L.:::f ~ '-...!.. i~
-- ; ~: --'"
i((': '""CUTOFF
MIXTURE CONTROL
~
H'SL'NE'S
.. ENGINE FUEL
PUMP L 1--.J
:---; /'
: :' -.
~ FULl.. RICH
'I
ii'
'I TURBINE WHEEL
V
FOR ELECTRICAL
I FUEL FLOW
, SENSING
73-00-03
The manifold valve receives fuel from the metering unit. When fuel pressure reaches ap-
proximately 3.5 psi, the valve opens and admits fuel to six ports in the manifold valve (one
port for each fuel nozzle line). The manifold valve also serves to provide a clean cutoff of
fuel to the cylinder when the engine is shutdown.
The injector nozzle lines connect the manifold valve to the six fuel injector nozzles.
The injector nozzles (one per cylinder) are "air bleed" type fuel nozzles which spray fuel
directly into the intake port of the cylinder. When the engine is running, flow through the
nozzle is continuous and will enter the cylinder combustion chamber when the intake valve
opens.
Since the size of the fuel nozzles is fixed, the amount of fuel flowing through them is
determined by the pressure applied. For this reason, fuel flow may be accurately determined
by measuring the pressure at the manifold valve. (Refer to Chapter 76 Performance Charts.)
All of the items described above are interdependent on each other to meter the correct
amount of fuel according to the power being developed by the engine.
7~1~00 SE~UPPROCEDURE
The full rich performance of the fuel injection system on all injected engines is controlled by
manual adjustment of air throttle and fuel mixture at idle and pump pressure at idle and full
throttle. Fuel pressures of fixed orifice pumps can only be adjusted with the relief valve
screw located on the centerline at the rear of the pump. Adjustable orifice or variable orifice
(aneroid) pumps have an additional facility for adjusting pump pressure at both idle and full
throttle RPM.
To make full rich adjustments on engines equipped with adjustable orifice pumps, run-up
engine to obtain normal operating temperature and proceed as follows:
A. Tee into either the fuel pump outlet fitting or metering unit inlet fitting (whichever is
more accessible) with an appropriate pressure gage and extended fuel line to observe fuel
pump pressures. (This gage should be properly calibrated and vented to atmosphere on all
engines).
B. On all engines, back the throttle plate idle screw out of contact with the stop. Use the
throttle to hold to the specified idle RPM.
C. To obtain pressure limits specified for idle RPM the variable orifice adjusting screw on
turbocharged engines is located on the aneroid housing and is turned CW to decrease pressure
and CCW to increase pressure.
CAUTION. . . Jam nut must be loosened before screw can be adjusted. Use care ill hoff!
looselling alld tightening this Illlt.
D. Maintaining idle pump pressure and idle RPM, correct idle mixture exists if, upon
leaning with the mixture control, an increase of 25 to 50 RPM is obtained, depending on
airport elevation.
73-00-04
The preceding steps have provided:
(1) Correct pump pressure
(2) Correct fuel flow
(3) Correct fuel metering cam to throttle plate orientation.
NOTE. . . Do not adjust idle mixture without first determining that idle pump pressure is
correct.
E. Advance full throttle and maximum rated engine RPM to check pump pressure and
nozzle (metered) pressure or flow. (Nozzle pressure or flow values may be monitored by
either the gage provided in the aircraft or an auxiliary pressure gage (which must be of the
vented type and be referenced to compressor discharge pressure in the same manner as the
aircraft fuel flow gauge teed into the fuel manifold valve pressure port). Criteria for full
throttle full rich adjustment of the fuel system should be specified nozzle pressure or flow
values. Unmetered pump pressures at full throttle are included for reference only and may be
used for troubleshooting the metering unit portion of the fuel system.
F. To obtain specified values of nozzle pressure or fuel flow at full throttle and rated
RPM. turn the adjustable orifice adjusting screw (located on the side of the pump) CW to
increase pressure and CCW' to decrease pressure or on adjustable orifice pumps adjusting
screw located on the aneroid housing CW to decrease CCW to increase pressure.
NOTE. . . If at static run-up rated RPM cannot be achieved at full throttle. adjust nozzle
pressure or fuel flow to obtain specified values when rated RPM is achieved during takeoff
roll.
CA UTION. . . On some aircraft, al/. pllmp pressure checks, mi;'(ture, and idle speed adjustments
must be pe10n1!ed with the aircraft aw:iliary pllmp 011 "low position". Refer to aircraft
mailltenallce mallllal for details.
CA UTION. . . Jam nllt must be looselled before screw can be adjusted. Use care ill both
loosening alld tightening tllis Illlt.
NOTE. . . If at static run-up rated RPM cannot be achieved at full throttle. adjust nozzle
pressure or fuel flow to obtain specified values when rated RPM is achieved during takeoff
roll.
73-00-05
73-10-02 SPECIAL SET-UP PROCEDURES FOR THE TSIO-360E, EB, F,FB, GB AND LTSIO-360E, EB
ENGINES
A. Takeoff rated MP and RPM are obtained at approximately 40° throttle travel.
NOTE. . . Setting the exhaust bypass bolt is extremely important. This setting determines Full
Throttle manifold pressure and critical altitude and must be properly adjusted before the fuel
system can be set up accurately.
NOTE ... See General Instructions for adjusting turbocharged engine fuel systems.
c. Rated manifold pressure for a given altitude should be achieved on take-off roll. If
rated MAP cannot be obtained, check for exhaust leaks, turbocharger condition, or calibration
of overboost valve.
D. To check actual critical altitude, the aircraft must be flown. Refer to Aircraft Service
Manual for test flight procedures. If critical altitude is not correct and fixed wastegate is
readjusted, the metered fuel flow must be rechecked and set to max. power (full throttle)
values.
NOTE. . . For further information on adjusting fuel injection systems see TCM Service
Bulletin M84-6RI or current revision as applicable.
73-00-06
73-10-03 FUEL SYSTEM PRESSURE AND FLOW VALUE CHARTS.
For your convenience, we have tabulated the following fuel system pressure and flow
values to facilitate proper adjustment and optimum performance of all TSIO-360 series
engines. All top end values are shown for max. rated RPM and manifold pressure.
NOTE. .. Unmetered or pump pressure values are for a gauge vented to atmosphere.
<D See Aircraft Specifications for other values where applicable.
@ Limits are based on aircraft manufacturer's gauge calibrations.
@ Limits also apply to the 'B' configuration of these engines i.e., TSIO-360-AB, TSIO-360-BB.
NOTE. .. For further information see TCM Service Bulletin SID97-3 or current revision as
applicable. I
This troubleshooting chart is provided as a guide. Review all probable causes given, check
other listings of troubles with similar symptoms. Items are presented in sequence of the
approximate ease of checking, not necessarily in order of probability.
Engine Will Not Start No fuel to engine. Check tank fuel Ieve!.
And No Fuel Flow
Gage Indication Mixture control improperly Check mixture control for proper
rigged. rigging.
Engine Will Not Start Engine flooded. Reset throttle, clear engine of
With Fuel Flow Gage excess fuel, try another start.
Indication
No fuel to engine. Loosen one line at nozzle. If no
fuel shows, with fuel flow on
gage, replace fuel manifold valve.
Engine Runs Rough Restricted nozzle. Remove and clean all nozzles.
Low Fuel Flow Gage Restricted flow to metering Check mixture control for full
Indication valve. travel. Check for clogged fuel
filters.
73-00-08
73-10-04 FUEL INJECTION SYSTEM TROUBLESHOOTING CHART
High Fuel Flow Gage Restricted flow beyond Check for restricted nozzles or
Indication metering valve. fuel manifold valve. Clean or
replace as required.
Fluctuating or Erro- Vapor in system, excess fuel If not cleared with auxiliary
neous Fuel Flow temperature. pump, check for clogged ejector
Indications jet in vapor separator cover.
Clean only with solvent, no wires.
Air in fuel flow gage line. Leak Repair leak and purge line.
at gage connection.
Poor Idle Cut-Off Engine getting fuel. Check mixture control is in full
idle cut-off. Check auxiliary
pump is OFF. If neither, replace
manifold valve.
Unmetered Fuel Relief valve stuck open. Repair or replace injector pump.
Pressure Drop
Very High Idle And Relief valve stuck closed. Repair or replace injector pump.
Full Throttle Fuel
Pressure Present
No Fuel Pressure Check valve stuck open. Repair or replace injector pump.
73-00-09
INTENTIONALLY
LEFT
BLANK
73-00-10
CHAPTER 74
IGNITION
74-00-00 GENERAL
74-10-00 GENERAL
74-00-01
(TCM IGNITION SYSTEM)
74-00-00 GENERAL
Conventional dual ignition is provided by two magnetos. The left magneto fires 1-3-5 lower
and 2-4-6 upper spark plugs, while the right magneto fires the 1-3-5 upper and 2-4-6 lower
spark plugs.
The TCM S-20 Series Magneto is designed to provide ignition for six cylinder aircraft engines.
The magnetos generate and distribute high tension pulses through high tension leads to the
spark plugs. Overhaul is recommended at engine overhaul or at the expiration of four years
without regard to engine operating hours, whichever comes first.
To obtain the retard spark necessary for starting, the magnetos employ an impulse coupling.
The purpose of the impulse coupling is to: (1) rotate the magnet between impulse trips faster
than engine cranking speed thus generating a better spark for starting the engine, (2)
automatically retard the spark during engine cranking, and (3) act as a drive coupling for the
magneto.
The following detailed explanation gives the meaning of the various letters and numbers
appearing in the type designations:
C. "R" or "L" indicates direction of rotation of rotating magnet viewed from drive end; "R"
for right-hand, "L" for left-hand.
E. The dash number (such as -25) indicates a certain execution of the basic type magneto.
Insure that magneto is proper part number for engine installation. Insure that internal timing
of magneto is correct as per TCM form no. L-250-10 (or latest revision) for S-20 series
magneto. This publication is included in TCM Ignition Systems Master Service Manual Form
No. X40000 (Printed Edition) or Form No. X40000F (Microfiche Edition).
CAUTION . . . When installing a TCM magneto on the engine, a gear holding timing device
should not be used, as hidden gear tooth damage may result.
Turn engine crankshaft until piston in the No. 1 cylinder is at its full advance firing position.
Rotate the magneto shaft in its normal direction of rotation until the painted chamfered tooth
of the distributor gear is centered in the inspection window. Install magneto on engine. Do
not tighten magneto hold-down bolts.
Fabricate P-Iead adapter using appropriate terminal kit and a length of wire. Install adapter
lead on switch terminal of magneto. Connect positive lead of TCM 11-9110-1 timing light, or
equivalent, to bare end of adapter. Connect common lead of timing light to a good ground.
74-00-02
If timing light is out, rotate magneto housing in the same direction as its magnet's rotation a
few degrees beyond point where light comes on. Then slowly turn magneto housing in opposite
direction until light just goes out. Secure magneto housing in this position and recheck
adjustment. Replace timing window plugs.
Repeat the above steps for second magneto. Check magneto synchronization with 11-9110-1
timing light or equivalent. If necessary, loosen magneto hold-down bolts of one magneto and
"bump" with soft mallet to synchronize magnetos. Tighten all magneto hold-down bolts. Refer
to Figure 72-50-01 for proper torque.
Disconnect timing light from magneto. Make connections between magneto and ignition switch
using 18 gage wire following airframe manufacturer's wiring instructions.
Before installing harness on magneto check mating surfaces for cleanliness. Spray entire face
of grommet with a light coat of silicone spray parting agent* to prevent harness grommet
from sticking to magneto distributor block. For S-20 series magnetos, install and tighten
screws around plate alternately to seat cover squarely on magneto. Apply 25 to 35 in.-Ibs.
torque to screws.
*Silicone spray parting agent 8512, IMS Company 10373 Stafford Road, Auburn, OH 44022.
74-00-03
The harness assemblies are constructed of a lightweight, flexible, silicone coated cable having
a 400 0 F temperature rating. Because the harness assemblies are lightweight and flexible, the
following suggestions should be observed when installing the harness on an engine;
A. Support leads with as many clamps and cable ties as are necessary to prevent any
whipping or chafing action.
B. Route leads as far away from exhaust manifold as possible to insure they are not exposed
to temperatures in excess of 400 0 F.
**Go-Jo No-Lok No. 72 Compound, Gojer, Inc., Akron, Ohio 44309 or Molykote Type G,
The Alpha Molykote Corp., Stamford, Connecticut 06904.
NOTE . . . Hold ferrules while tightening or loosening spark plug coupling nuts to protect
against twisting conduit or cable.
D. If elbow assemblies are not used and installation results in a severe angle where conduit
connects to the spark plug, use clamp PIN 10-320283 as shown in Figure 74-00-02,
"Installation of Elbow Clamp". Secure clamp with screw and lockwasher PIN 10-35936-6 and
nut PIN 10-90404-4. The clamp will maintain a 70 0 elbow eliminating overstressing the lead.
5/8-24 90-95
3/4-20 110-120
(SLICK IGNITION SYSTEM)
74-10-00 GENERAL
Conventional dual ignition is provide by two magnetos. The left magneto fires the six (6)
upper spark plugs, while the right magneto fires the six (6) lower spark plugs.
The Slick 6214 Series Magnetos, manufactured by Slick Electro Incorporated, 530 Blackhawk
Park Avenue, Rockford, Illinois 61101, are designed to provide ignition for six cylinder light
aircraft engines. The magnetos generate and distribute high tension current through high
tension leads to the spark plugs.
To obtain the retard spark necessary for starting, the magnetos employ an impulse coupling.
The purpose of the impulse coupling is to: (1) rotate the magnet between impulse trips faster
than engine cranking speed, thus generating a better spark for starting the engine; (2)
automatically retard the spark during engine cranking, and (3) act as a drive coupling for the
magneto.
The following detailed explanation gives the meaning of the various numbers appearing in the
serial number.
EG-203132
The month of
Manufacture
(03 = March)
Before magnetos are installed on the engine, the rotation and internal magneto timing must be
correct. For rotation and interval timing procedure refer to the appropriate magneto manufac-
turer's instructions.
The magneto to engine timing check to be performed at every 100 hour and annual inspection.
CAUTION. .. Be sure magneto switch is OFF and ''P'' leads are grounded.
1. Remove top spark plug from number one cylinder. Place thumb over spark plug hole and
rotate crankshaft in normal direction of rotation to ensure piston is on compression stroke.
Rotate crankshaft in normal direction until it is approximately 35 degrees BTC on compression
stroke #1 cylinder. Again turn crankshaft in normal direction until the 20 degree BTC mark is
aligned in the center of the timing hole.
74-00-05
2. Insert the T-118 timing pin in "L" or "R" hole (depending on magneto rotation) in the
distributor block. Turn rotor in the opposite rotation of magneto until pin engages the gear,
install magneto and gasket on mounting pad of accessory housing and remove timing pin.
Secure tightening bolts finger tight.
3. Connect a standard timing light between engine ground and left magneto condenser
terminal. Switch must be "ON".
4. Turn the complete magneto opposite normal rotation of the magneto on engine mount
until the timing light indicates the contact breaker points are just opening. Secure magneto.
Turn switch "OFF".
5. Turn on the switch of the timing light. Rotate the crankshaft slowly in direction of
normal rotation until the timing mark on the front face of the starter ring gear aligns with
the drill hole in the starter housing, at this pOint the light should illuminate. If not, turn
magneto in its mounting flange slots and repeat until light illuminates at the 20 degree BTC
indication. Secure magneto.
6. Connect other positive wire of timing light to right magneto condenser terminal and time
the magneto in the same manner as left magneto.
7. Following timing of both magnetos, with timing light wires still connected, recheck
magneto timing as previously described to insure that both magnetos are timed to fire
together. If timing is correct, both lights will illuminate simultaneously when the 20 degree
indication on the ring gear aligns with the drill hole in the starter housing. If points open
early, loosen magnetos and rotate counterclockwise. Secure magnetos and remove timing lights.
CAUTION . .. "When installing the magneto on the engine using the available nuts and clamps,
please take the following precautions. Tighten both nuts by hand to finger tightness. Tighten
each nut to 8 ft.lbs., and then tighten them alternately in several steps to 17 ft.-lbs. exceed-
ing 17-ft.-lbs. may cause the mounting flange to crack.
For further information on the magnetos and ignition system refer to the applicable manufac-
tures instructions.
Before installing harness on magneto check mating surfaces for cleanliness. Install and tighten
nuts around plate alternately to seat cover squarely on magneto. Torque nuts to 18-22 in.-Ibs.
The harness assemblies are constructed of a lightweight, flexible, silicone coated cable having
a 400 0 F. temperature rating. Because the harness assemblies are lightweight and flexible, the
following suggestions should be observed when installing the harness on an engine:
A. Support leads with as many clamps and cable ties as are necessary to prevent any
whipping or chafing action.
B. Route leads as far away as possible from exhaust manifold to insure they are not exposed
to temperatures in excess of 400 0 F.
74-00-06
*Fluorocarbon Spray MS #S-122, Miller-Stephenson Chemical Co., Inc.,
16 Sugar Hollow Road, Danbury, Connecticut 06810.
**Go-Jo No-Lok No. 72 Compound, Gojer, Inc., Akron, Ohio 44309 or Molykote Type G,
The Alpha Molykote Corp., Stamford, Connecticut 06904.
NOTE . . . Hold ferrules while tightening or loosening spark plug coupling nuts to protect
against twisting conduilt or cable.
5/8-24 90-95
3/4-20 110-120
74-00-07
74-20-00 IGNITION TROUBLESHOOTING.
This troubleshooting chart is provided as a guide. Review all probable causes given, check
other listings of troubles with similar symptoms. Items are presented in sequence of the
approximate ease of checking, not necessarily in order of probability.
Engine Fails To Start Ignition switch OFF or grounded Turn switch ON. Check for
Due To Ignition Trouble switch wires. grounded wires.
Rough Idling Spark plugs fouled or improperly Clean spark plugs. Adjust spark
gapped. plug gap.
Sluggish Operation Fouled or dead spark plugs. Clean spark plugs. Replace dead
And/Or Excessive spark plugs.
RPM Drop
Improperly gapped spark plugs. Adjust to proper gap.
74-00-08
CHAPTER 75
AIR
75-00-00 GENERAL
75-00-01
INTENTIONALLY
LEFT
BLANK
75-00-02
75-00-00 GENERAL
The induction system components include the aircraft filter/alternate air door, turbocharger
compressor, aftercoolers, throttle, manifold and cylinder intake ports. Air flows through these
components in the order they are listed.
The turbocharger compressor is a high volume air pump connected to the opposite end of the
turbocharger turbine. It increases the pressure of air admitted to the cylinder for combustion.
At high compressor discharge pressures, considerable heating of the induction air occurs, due to
compression.
The aftercooler is a heat exchanger which lowers the temperature of the compressor discharge air
to permit more efficient engine and turbocharger operation. The induction air passes through the
core of the aftercooler and transfers some of its heat to the cooling fins which are exposed to the
relatively cooler ram air.
The manifold is an air distribution system mounted in several different configurations according to
engine model. It serves to carry induction air to the individual cylinder intake ports.
The cylinder intake ports are cast into the cylinder head assembly. Air from the manifold is
carried into the intake ports, mixed with fuel from the injector nozzles, and enters the cylinder as
a combustible mixture when the intake valve opens.
Overboost protection is provided by a pressure relief valve located between the compressor and the
throttle. In the event of a wastegate or controller malfunction resulting in excessive discharge
pressures, the relief valve will open to prevent excessive manifold pressure.
75-{)O-O3
INTENTIONALLY
LEFT
BLANK
75-00-04
CHAPTER 76
ENGINE CONTROLS
76-00-00 GENERAL
76-10-00 CRUISE CONTROL BY PERFORMANCE CURVE
76-20-00 CRUISE CONTROL BY E.G.T.
76-30-00 PERFORMANCE CHARTS
76-00-01
INTENTIONALLY
LEFT
BLANK
76-00-02
76-00-00 GENERAL.
The curves in this chapter represent uninstalled performance and are provided as a reference
in establishing power conditions for takeoff, climb and cruise operation. Refer to aircraft
manufacturer's flight manual for tabular climb and cruise data.
3. These engines are equipped with altitude compensation fuel pumps which automatically
provide the proper full rich mixture at any given altitude. Adjust mixture to lean out
fuel flow for cruise settings according to applicable fuel flow vs. brake horsepower curve.
CAUTION. . . Ulhen increasing power, enrich mixture, advance RPM and adjust throttle in
that order. 'When reducing power, retard throttle, then adjust RPM and mixture.
NOTE. . . It may be necessary to make minor readjustments to fuel flow (mixture) after
changing RPM.
2. Slowly move mixture control toward "lean" while observing E.G.T. gage. Note
position on the instrument where the needle "peaks" or starts to drop as mixture is
leaned further.
3. For the maximum recommended cruise setting see Aircraft Operation Manual.
CAUTION. .. Do not attempt to adjust mixture by use of E.G.T. at setting above 78% of
maximum power. Also, remember that engine power will change with ambient conditions.
Changes in altitude or outside air temperature will require adjustments in manifold
pressure and fuel flow. (Refer to Charls Fuel Flow Vs. BHP).
Gauge fuel flow should fall between the maximum and minimum values on the curve. If
not, the fuel injection system or instrumentation (including tachometer, manifold pres-
sure, fuel flow gage or E.G.T. system) should be checked for maladjustments or calibra-
tion error.
76-00-03
INTENTIONALLY
LEFT
BLANK
76-30-00 PERFORMANCE CHARTS
76-00-05
TITLE PAGE
Critical Altitude Variations (typical) Simple Turbo Systems TSIO-360-F,FB,GB,KB ................... . 76-00-58
Speed Correction Chart S/L to 2000 ft. MSL TSIO-360-F,FB,GB,KB ........................................ . 76-00-59
Sea Level Performance L/TSIO-360-KB ...................................................................................... 76-00-60
Fuel Flow VS. BHP L/TSIO-360-KB ............................................................................................ 76-00-61
Altitude Performance 2200 RPM L/TSIO-360-KB ........................................................................ 76-00-62
Altitude Performance 2300 RPM L/TSIO-360-KB ........................................................................ 76-00-63
Altitude Performance 2400 RPM L/TSIO-360-KB ........................................................................ 76-00-64
Altitude Performance 2500 RPM L/TSIO-360-KB ................................................ '" .................... . 76-00-65
Altitude Performance 2600 RPM L/TSIO-360-KB ........................................................................ 76-00-66
Altitude Performance 2700 RPM L/TSIO-360-KB ....................................................................... . 76-00-67
Altitude Performance 2800 RPM L/TSIO-360-KB ........................................................................ 76-00-68
Power Management Operating Recommendation L/TSIO-360-KB ............................................. . 76-00-69
Metered Fuel Pressure VS. Fuel Flow All Models Except TSIO-360-LB & MB .......................... . 76-00-70
Typical-al Engine Fuel System Operating Characteristics 2600 RPM (Standard at S/L)
All Models Except TSIO-360-LB & MB ......................................................................................... 76-00-71
Fuel Flow VS. Pressure Drop TSIO-360-LB .................................................................... ............ 76-00-72
Mixture Ratio Curve 2200 RPM 24.9' HG. ADMP. TSIO-360-MB, SB ....................................... 76-00-73
I
Altitude Performance 2200 RPM TSIO-360-MB, SB .................................................................... 76-00-104
Altitude Performance 2400 RPM TSIO-360-MB, SB .................................................................... 76-00-105
Altitude Performance 2500 RPM TSIO-360-MB, SB .................................................................... 76-00-106
Altitude Performance 2600 RPM TSIO-360-MB, SB .................................................................... 76-00-107
Altitude Performance 2700 RPM TSIO-360-MB ........................................................................... 76-00-108
Critical Altitude Variations TSIO-360-LB ...................................................................................... 76-00-109
~; :::: :::I :::: l.t.,:; ;::; ~::: :::: ::: :::: :~:: ;;:: ::;: Recommended--Fuel Flow Vs Brake Horsepower - :::: u:_: ::~: ::::f::': :;:: :::1 .::: :-:-::~:':~rm
i
):.
OJ
10
10
OJ
:1':::1:.
"'-'--'-'::J::::l::::l::::I::::I::::I::::I::::I::::!20'····1····
:1::
~:L.'-+--r-:i- . - . m:':':~·~·I··
-: \... '1" .\. -T" 'j' --tn:::::.:.~: I:::: I::: :1: ::: I::::!:::: I:: ::1:::: 1::;:1: :::j::::U:::f:::l: ::l:::~
I::::I::I:::Y:'I::.\ -~ ,• •~o:~t----L !••.cir/ •'... :'1-1'0'\' :::. :::- ::'1'30--:: :::: :::: ::'1-5'0'\-: :.:: :::: ::-1-7-0'-: :::: :::: :1'-1'9'0':: :::: ::-:.: ::2-'10":: :::: :::: ::: .
. • . .••. .• -. .• ~.. • .. .... ... . •.•. .•.. .• ." . .. .••. . 1. ••• • • •. • j ••• • t. • ••• - "'_
., - ,,- .. --- -- '- .--.\ .. -- ., . -.. - .. -.. - _ ,- --·-1-- .. - .- .. ,: .---- -, .- --,. --.- -...
t -.-
. :
::
.: ... i.' ::I: :::1' :::I: :•:1: •::1: :::1:: :;1:; :;1: :::r:1: ::: Itt:;:::: B~ake Horsepower tr: ::: r: ::!.:.: v:: r::. F::~ I:~~T::: r;:· W~Ti q:. ~ :li~ :l··· p~~
dH H ' ___ -H_ . . . . . - •• H ..... H •. - .••••
:::::~ • ::::: I::.:::: -r::::: ::::rift:
• • ••
%H- 1'" •• , . ••••
:: :::.:1:: :::: ::: :~:::;::::: :::: ::::1:::: :::: ::~ :::: :::l::l.:l:::I::.l::~.~ -- -.-.
.••. •.•• . • • . 1 •• " •••• •••• • •• •••• •.•• • •. ~. •• ~. ,. • • , . .••• ..". ,"'" • • -+. •••• •• ~. •••• • ••• " ..... ••
i
E Max. Allowable ADMP
~ 32
~
~
I
30
E
E
V
D.
~ 28
E
/
/
210
V
~ ,/'
~ 26 \>-Q'*V
V / 190
/
~ /
vi
lID
-< \>~o~
/' DI:
24
/,V
l, ~\~
i VV / 170 ~
22 150 ~
~"v---
G~p ~
6~
/
'yoo
0 130 ~
V <
E
---- ~
V
-x1}.
110
~
90
/'
iii
::z:
E
I
-- ---
-.:. .700 70
::z:
•
~
1----r---..
'::
~ .650
~R·h
vi
':: ~FC
~ .600 r--
-
........
:'.)
IA.
~ .550
/
'" .500 E
E
/
V
- Prop. Load IBSFC
I
-::---
/'"
.450
1800 2000 2200 2400 2600 2800
ENGINE RPM
uJ 1 ! '2200 , I. 1
80 I I ___ 1 --+------. --.i 1 '1
+_+____
80)
1 ; , .'
c;s I '
w 60 60
) " I ! : I '-,--, f---- f-----l-,-- I--j-+~---,t ~~, I, i" I
-LII~"':
, "
~tI',---C- --~,--~i,I".~
£ 40
:~-------+--+i--I~'-+- -1 r' Iii -~ I i ,!~
~ 20 20
m ~~~~_~~~~~~~J-L__~~i~,~LU i i il
m
tIl
16 Ie 20 22 24 26 28 30 32
l~IIIIIIIIIIJI_.:~
i § ~ ~ ~ ~ I ~ ~ ~ ~
i i I Ii i ii i ~ ~ ~ ~ ~ ~ ~ ~~~~ ~ U~
AII5. DaY MANIf<lll) I'IIUSUIIE IN. He> ~ PlESSUtf AlTITUDE IN flU
!
"-"
.....
~
0
0
...,
0
140 /
V
130 J /
V
120
V/ /
./ / /
V
110
/' /
""c ." ;;;
!l cm
r- 100 RIC,H OF PfAK- '
F
""0" ."
V.J~~~50
~ ~\Cy.. ~,.\- 0
80 RICH OF PEAK
== r- \)\- I I I
< 0
90 0
~ :! ~?~ ./ V ' 50 RICH OF PEAK-~
m r- ~ ~\- I I
:::c tJ:J F V /' .V'
"0 !oil V~/ / JI""'" / ' ..... 1,.;,. PEAK EGT"
-I 80
en :t APPROX. BEST POWER~ ~
:II
9
Co)
- = FUEL BELOW 75%
. / ~ . , . . /V /'''
0) ./""~ / ~
70
C? .... / '
0 ~
'0 :/: / ....
v:::
......
m 60 ::::: ~
J.: ~,. /L "
MINIMUM ALLOWABLE FUEL FLOW
'/ ...,....,. JI""'"
. I
50 ......
~ ~ ,.,........ /
I
EV 7 . . . . . ~ *LOCATED TURBINE INLET
'11!.-" ~ ~."....,.......
40 ~.,..
~ II
30
t
70 90 110 130 150 170 190 210 230
BRAKE HORSEPOWER
III
37
FUJ THRJTTLE ~
./
V /
35
V
ci
J: 33 /
Z V Fi=
~ 31 /
sf} /
w
a:
0. ",0
Z 29 O~ 240
<
~ ~~
>
a: 27 ~ A 220
[,7
0
~
< 25
V
V '\"'~
V V' 200
/
0'\
23
-
V :P
\)",'" 180
a:
w
3:
~ 0
21
V / V' / 160
0.
W
CI)
a:
~
V ",0
0
J:
V O~
~<l' 140
w
:ac
<
V V
~
120
a:
!Xl
a: '/
J:
-..
0.
J:
/
7' 100
~OpLO V
!Xl
.......
0
!Xl
..J .60 J 80
0
Z
.~ r---....... ~ VJ
0
c.J
..J
W
::;:)
u.
.55
.50
..... FULL THROTTle
,
--.;
- ~
.../
iii"'"
c,j
w
8s
1800 2200 2400
ENGINE RPM
76-00-11
C(>
""
o
?.....
I\)
E ! I
140
I I v
I
I I
t: ! I
!:: I
I I I
130 !
VV
E I I I I
i::: I I
!::
I I i 1 ./
!i
120 I
V '"V
,~
I
!
E I
II I V/ ~
110 i /
I i !.,/
"TI
c::
E i. V E
(t) I i1/ /'
100
75° RICH OF PEAK
-"TI ." ~ ~
0' c:: , \,.\~,-';"t' ~
=E m i L
I I ~
< r- 90
l ~\C;~ / 50° RICH OF PEAK
(f) ." t: /"
aJ
r- E i%~I/>' I
I Q~ "" ~
::x:: E I \,.O~ ! / ~ ,." PEAK EGT* E
t::
"'C ~ 80
-I -r- """
en ~
0 ~
W :..... / '~~X- "/ . j"'" r-
m :r:: 70
0 ::rI ........../".~ 1- I
I
c• -
b 60 !=
I ./ i I
c:J
i! I
~V~~J"""",,""""":
/1
E I
i~ .........-1 ;---MINIMUM ALLOWABLE FUEL FLOW
E .". I I . '
50 ~~~~V t::
" I I
~ .. ............i - I I
i I I I
I ,
40 ~~ ~ ... "" !
~~ t'" . . . 1 iI I I
i *LOCATED TURBINE INLET
~~ : i ! II ! I
30 1
I
-
I I
I
;
F i
... I I
~-: I !i j
1 1
70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230
I
~....
c,.) BRAKE HORSEPOWER
FULL'THRO+TLE
36
~
34
~
v
/
c:J
::r: 32
v
/
z
en 30 /
~
C/)
UJ
a:: ",0
Q. «.O~
28 240
Z
<t
:!!
./
V
>-
ex: 26 A 220
V /: ~
0
en
co 24 ./ 200
<t
V
~'\'Y
/ '\~«.~ V 180
ex:
/
22
'" UJ
./ V'~
;':
0
Q.
~ UJ
20 160 C/)
~
V ex:
0
,,/ 0
R"
140
::r:
UJ
/'
~
~
<t
ex:
/ 120
co
ex:
::r:
--
Q.
::r: ./
V
co 100
--enco /'
...I
en .650 V 80
z
0
(.)
~
/ FUll THROTTLE
.,
...I .600 60
/'
-
UJ
::;)
.............. V
u..
U
UJ
.550 r--- 10..... PROP LOAD
Q.
C/) t=
IIIll 11, III
7tHlO-14
SEA LEVel PERFORMANCE ALTITUDE PERFORMANCE
!O I2U1BrL!IM£ ~'D.!~L I:!f
to('; RPM A ""AN PR ON All CHART IPTA',
II
loe RPM. MAN PR ON S L CHART (pTe",
l'R.ANSfER "e- TO S L. ON AlT CHART (prc")
O!UW UHf fROM'C THRU "",0
lOC PT '0' AT PA ALTI AOOHP
»
::;: .~~~~~~ ~~~~~~;: _~~~ ~~~~?;S "
;::;: ~81 ~~~~;ciA~"'(,'~Tl~~~ t:~~ BElOW 1S
C 2.0 2.0
a. 2800 RPM - "AX. CONTINUOUS
CD
"tJ 220 220 _36.0IN HG
I'J' '.,-j,AN1IFOLO PRESSURE
CD
:t 200 200 L ~O I
0 a:
... ~
0 ~o
3 180 180'
D)
..... 2600 RPM •. MAX. CRUISE
::s '"a:0
(') 160 :I: 16C
CD
~
-t ~ ____ .. _ 1.0 .. 1.0
~
9 ---l120 120
'"
W
Q) 1
100 100
? !
C
80 80 ~
b
m
60 60i ~
40 401 i
I
~ 20 n ~ u ~ ~ U ~ 36 36 1 2 3 .. 5 6 1 8 9 10 11 12 13 14 lS 16 17 18 19 20 21 22 23 24 25 26 27 18: 29 30 31 32 33 34
ABS. DRY MANIFOLD PRESSURE IN. HG.
f~111111111111111 RJl4IttU1I11iII~ PRESSURE ALTITUDE IN THOUSANDS - FEET
.."
<{J
Q
?.....
<.n
rr Iii 111 II
<p
"'" r I I I I I I
0 ::::
4f> to- WARNING - Continuous operation at fuel flows leaner
..... than 25 0 F rich of peak. T.I.T. is prohibited
CD
::::::
::: for all conditions
Continuous operation at T.I.T. in excess
150
:::-
t:: of 16500 F is prohibited ./
E
t::
E
I- I I I I I 1.//
140
- - - Represents limits variations from '/
~ sea level to 12,000 feet I
130 ~ / v/
~ V
. )
120 /
"T1
c
!!!.. "TI
"T1 ·c 110 / /~
0- m
=: r- V V~v
"TI V O~~
<
en r-
«-'v v
0 100 I-
OO ~
::r: ~~ ~ K>~"
~v
"'CI «../ ~
r-
~ 90 ~
~. 1= 0....,.</;" V/ ~~
~ J: ~
::n ~
9
(..)
80 ~ ~
CD ~
E== /1
4f> E ~;!:;
,!T1
m 10 ~
00 r= / O"''''~'/ I-- -- - rOOD rT.-75rOWER
!=
E
60 ~ /" ~'" 'I>"'~ '/~~~ "SEA LEV EL- 75% POWE A
r= ~ \~$>-~~Y>
~
E ~ ;;" .. ~\..\..
50 ~
V ~vv ~v~
~
~
t- V /:vV~\~\1
~ ./
40 ~ J.M'f U«
60 80 100 120 140 160 180 200 220
BRAKE HORSEPOWER
30 40 50 60 10 80 90 100
PERCENT SEA LEVEl POWER
~ ~I-
~
FI=+--+-10-I-L..MINIMUM PRESSURE ALLOWABLE TO PROVIDESATISFACTORY FUELSYSTEM-~ I-
~ PERFORMANCE WHEN A BOOST PUMO IS NOT PROVIDED FOR VAPOR ~
~ SUPPRESSION. ~
~ WHEN A BOOST PUMP IS PROVIDED, IT MUST BE ABLE TO SUPPLY ENGINE -~
~I- DRIVEN PUMP INLET PRESSURE ABOVE THE MINIMUM VALUE TO SUPPRESS §
~ VAPOR WHEN PRESENT. ~
~ ~
f.::: IDLE 20 40 60 80 100 ~
~ F
~ ~
111111111111111111111 11111111111
PERCENT - RATED POWER
76-00-17
III
cj
J: 40
1',",~0~V
;2 /"
u) 35 f\)\..\.. ---- /
V 210
CI)
~ i-"'"
w
ex:
Il..
~
V /" ~ 7
30 190
2
o~~ v
~
~
~ V V
---
>- 25 170
ex: ~
Cl
u)
co
~ 20
0-<"
-<.."<C''L'
/ V 150 ex:
w
v"" /-"
<c ."".
,y.«'
""
/ 130
s:0
Il..
w
/V
CI)
ex:
V 110
0
J:
w
.
0
R\,;
sf/ ~
~
ex:
co
q,~~
90
V 70
V
~ 50
ex:
J:
--co
Il..
J: 30
--co
CI)
--
u.. .5
c.)
W
Il..
CI) II' 111111 II
1600 1800 2000 2200 2400 2600
ENGINE RPM
76-00-18
SEA lEVEL PERFORMANCE ALTITUDE PERFORMANCE
TO DEHBUIHE ACTVAL HP
"'"
?....
(J)
..... IT
cp DllIIIIIIlIIII ITTTTTTTl mrrnm mmrm rmmm rrr
0
0,
I\)
0 I I, I I
WARNING· Continuous operation at T. I. T. in ex·
C1!SS of 16500 F is prohibited
150
140
130 /
." 120 L //
c ."
~ c:
." m
,...
0' ." 110
/ '//V
~ ,...
~ i
m ,... 100 /~~
::x: ~
"tI
'-
::x:
~ ill
vd$
90 L
9w \CJY- ~~ ,,'l-~o<,;.
en \..~ ./ V i·'-
T> 80 <c~\.. \CJY-
J ~.:'\l: ~.
." \,~f>- i~'
-:" \'f'f>-i-' ~\..\.. ~
" I ~f>-'f.
m ~~<:;) i~<C ~O/
/ ' i' ". \'
~<.;,~ \*-f>- \,0 "", L
70
O~ 0;': ~Si'/ ./ ,,'
j:/ f>-\'\' V ~SEA LEVEL· 75% POWER
Oi-~
~t.. /~/
60 ~\1' '-
~ f>-~~~~~
L:::[...o .~~ \..O\tl~
~/ ~u~p..\..
50
. /~
"" ,.." ~~\~\
~ ~ ~.~
11'1' lMr
40
60 80 100 120 140 160 180 200
BRAKE HORSEPOWER (PROP LOAD CURVE)
30 40 50 60 70 80 90 100
PERCENT RATED POWER
II Ill.
42
ci
J::
Z 38
/ ~V
V
<Ii
(I)
w
a: 34
FULL THROTTLE -/ ./ 200
/ V V
~
Z MANIFOLD PRESSURE
« ./
::E 30 ~ ~ 180
~
>-
a:
0
~ 26
«
"...
~ / V 160
PROP LOAD
"" / /V
22 140
./
V /
/ ~
120 w
a:
w
::
/ '" /'
(I)
/ HORSEPOWER a:
FULL THROTTLE o
100 w
J::
V :.::
«
/ 80
a:
IX)
PROP LOAD /
a: 60
J::
-..
~
J::
~ .700 40
~
...I
<Ii
z .600
FULL THROTTLE
"-. "... ~
~
./
~
o()
...I
W
~
cJ
w
~
(I)
.500
PROP LOAD
FUEL CONSUMPTION
--- ....-......- ~
76-00-21
....,
cp
o
<?
1'1)
1'1)
~ , I
, tOC RPM' MAN PA ON ALl CHART jPr..")
i
LOC RPM" MAN PA ON S L CHART (pre")
,, 'tRANSFER "e" TO S.L ON All CHART (prC1 . ;
., ORAWUHE FAOU"C" TMRU ".." f
tOC PT"O" AT PRAlT" READHP
• fA~~;~ ~~:~~: ,!M~ ~~~~~;s
(a) SU9TJ\ACT ,"- fOR UCH _a,,:, Of" BELOW TS
,TS STANDARD ALTITUDE TEMP)
I
» 200 200 , I-- 4'
;::;: /
;:+: I-' V ~40
C / '10 '10
Q. a:
w
(I) K
?
-a
/ V/
/~l/ '00 ~
l:!
a:
'00
,
p~ ::;;;<..----
~ ::::V
""
- f.-~
V .).~
VV ~ ,
: . ,
11;
1 - 1-.- ~ bf· 17. el: k--"
w )~ -"" I I
~... 17/ ::5~F- " t><1-' V~ ..- ~~ MA.lfOLD .......,R. "toG.
I A.. i j
/ ~~ '10)
___ k" f.-
a:
3Q) . ., .."
co ...... V
:::s V/ ~ 'A , V k ___ ~..- 1'\1.. . ..1-.......1><:" "~I !
g f - 1-- '50 '50
,, l\ I ,
, » .:. __
(ij ~ ij '/ V '40 '40
--- l>c~
r-.... "v" I'-.. vI---' K~
vk ~
f-""
v~ ~k-".J....... f'- ~I.---~"~ "
,»
./j ~ / I ,» ,K
9 V 1'-.........- '" 21 t-I-
...........
/. ~V/ / f-- '20 '20
, IS:, _ v~~ D~~~~ b~~~1\
~ 1
;,
" / ~ 7/ [7/ 110 11 , ""K _vK ~~~ ~v~
CD 7/ 17
/0V/ 100 100
.... K ~---k: '~~~~ "", h j
RPM 2000 2200 2300 2..0 2100 251&
~~ V 7 10
~~~~:t.t.(1 ./ .f
I I 00
=
-
NOTE:
1. ContinuQus operation at TIT in excess
of 16500 F is prohibited ~
/
V
V
/
V
,,' 100
-
110 -;::
::::c
en
.0
-l
~V /
",,'" 3:
". 0
-l
"" "" 90 u.
~\cyV
",,"
".
-l
w
<t:'0'P ./
,..~
::>
... " u.
.
~~
~i-
~<t:,,\) ~ ~\cv-.
~~
V
,.. " " "
"
t...
r"" NOTE 3
...... I
80
r
'0\;\; ,..
70
O~~ ~~<t: ~o~'" ~
«-.~c ~,~\' 1 ~s'\
~ ~,..'" 0 ~?~
~~~o ~t>-"\ " Co~S~ 60
~ oi--'" u~y~
!"~~~T'"
~0~S
~
~~c,\ 50
~ .
...
I..L NOTE 2 ...
v
40
I
"
100 120 140 160 180 200 220
BRAKE HORSEPOWER (Propeller Load Curve)
76-00-23
40
0
:r:
z 38 V~V /
u:i
(/)
LLJ
36
,,0
V
«:-0
/ 210
~
0:
«v
0...
Z
<t:
:2: 34
#-
~<;) / / VJ 200
>-
0:
0 ~ ~
vO /
/ /
32 190
u:i
co
<t:
30 lP/ / /
1/
180
0:
LLJ
V
/
V V ! -
170
S
0
0...
LLJ
(/)
0:
0
"S/ ;,.../
/ .-
160
:r:
LLJ
~
<Pj
;,...-<'
'V
~
/ 150
<t:
0:
co
«.
..:::;'V <0
sF/ 140
B
ci
:r:
--
0...
/
/ Q..Q;-
'/ 130
/
:r:
co
--
(/)
co
-l .80 120
u:i
Z
/
-~
0 .70 110
u
V FULL THROTTLE
--
-l
LLJ
:::>
u.. .60 / BS:FC ~ 100
cj
LLJ
0...
(/)
.50
/ PROP LOAD
90
20 22 24 26 28
ENGINE RPM
76-00-24
I
I
»
;::;: r----+-220
1 -I I ~
:;:; NOTE:
c: 1. FULL RICH MIXTURE 75% POWER AND ABOVE.
'
0- r----+-200 I I ---1 I 2. BEST POWER MIXTURE BELOW 75% POWER.
Cl) 3. CORRECT BliP FOR INLET AIR TEMPERATURE AS
-t
"0 FOLLOWS:
Cl) >---+ 18041--+--+--+---1--+--\--+--1---+
a. ADD 1% FOR EACH 60 F. BELOWTs.
--
b. SUBTRACT 1% FOR EACH 60 F. ABOVE Ts.
a-... t--+160 ! 1--·-1--· I tl
3
I»
::l I-~ \--140 I I -. E1
(') £"
Cl) J:
.... H 1 120 32 IN. HG. MANIFOLD PRESSURE
CIO ~ I
o - 1 a
o I-~ 100 28 '
:::D
"0 1--+-80 t:t
3: 24
-I t---l--so I~ tl
en 20'
t---l--40t--r--t-i-==t=~~=F--~~--t-t--1--t--!--t--t--t-t-~
9w
0) 16
C?
G)
t---l--20~-+--+-'-~-1----+--'-+---I---+----+---~-1---+---+---I----+---+---t--fl
m
!---
o 2 6 8 10 12 14 16 18 20 22 24
I I I I Iii i ~
B Altitude X 1000 Feet --i II
I r+-- I +i I
I i I I I
I , \,! L,LL]
......
cp
o
C?
I\)
<.n
"'-I
cp
o :.~ ...
~
en
220
1--t-- 1* I I II iI.!, I II I . !I ' ·1 I_Tj
I I: NOTE: I ____
I : j
LJ'I 1. FULL RICH MIXTURE 75% POWER AND ABOVE.
1--t--200 ; ! i 2. BEST POWER MIXTURE BELOW 75% POWER. --
I I 3. CORRECT BHP FOR INLET AIR TEMPERATURE AS
l> --
;:; 1--t--180 I I :'O;~~~; FOR EACH 60 F. BELOW Ts.
;::;:
b. SUBTRACT 1% FOR EACH
a
('I) 1--t--160 I ~-.~--~---+---+--~--~~--~--.~--+---~--,----~---+---+-
"'0
('I)
~
... r!f140 32 IN. HG. MANIFO~D PRESSURE -i--
3
\U rg 120
:l
(') ~::;'" 28
('I)
1-£1; 100 ~
~
o
o d
JJ I~ ,-.,L,--l---t-~~-+---t--1---t--j~-r---r~
"'0
s:: D I 60 riO -r==r=+ p" .
~
9w
9
G)
m I
I I
o 2 4 6 8 10 12 14
! I i
Altitude X 1000 Feet
I ,1~J
1----+ 220 , tj
NOTE:
1. FULL RICH MIXTURE 75% POWER AND ABOVE.
1---+200 I I 2. BEST POWER MIXTURE BELOW 75% POWER. --
3. CORRECT BHP FOR INLET AIR TEMPERATURE AS
l> FOLLOWS: --
;::;: 1----+ 180--111---+-+--+--+--f--+-+-+---+
:::;: a. ADD 1% FOR EACH 6 0 F. BELOWTs.
C 0
I--- I I I I I I I I b. SUBTRACT 1% FOR EACH 6 F. ABOVE Ts. i
0.
(f) 1----+160 r---- 36 I!:!,: HG. MANIFOLD PRESSURE I I I I I I I I
"tlI :- --.........
140
~3 f-@1 32 ~
I»
~,-
f---~ 120 28
"'~ ..............
:::s .gj -..:;;:-- -.....,
~ ~ t:::::,. I I I i I I I
f-~ 100 24 _ r--... I I I I I I +- I I Ei
~
o - .:::::.- ! "-..,
t1 80 ' I I I I I I I=l
:::0 20 _- I ~ I I I I I I 8
"tlI
i: D 60
-~ ~ I I I I FI
-I ~__ I I I I ]I
(I)
9w D 40- , --
i
~ D I 20~1~--+---~---r---+--~~--+---~---r-
G)
0:1 r
I
I I I I
o 2 4 6' 8 10 12 14 16 18 20 2,2 24
I I !
j j I I I i
Ij ·r-· --Alt\tude X l000 tj
1 Frt --1
.1. • . . . I. L, i • I
.....
q>
o
o
•
I\)
.....
.....
'P
o
~CO
ill
! i i
I 1 -r
~ 1--220 ~-
I I
I NOTE:
I
I I I
1. FULL RICH MIXTURE 75% POWER AND ABOVE.
f-- 200 I i i 2.
1-+
BEST POWER MIXTURE BELOW 75% POWER.
-
40 IN. HG. MANIFO~D PRESSURE I 3. CORRECT BHP FOR INLET AI R TEMPE RATURE AS
» f - - f.-180
.......... I FOLLOWS: -
::;: ............ a. ADD 1% FOR EACH 6 0 F. BE LOW Ts.
;:0: 36 l:::::::::.. I b. SUBTRACT 1% FOR EACH 6 0 F.ABOVE Ts.
B- f - - f.-160
r---... I
CD 1 +
32
~
"'0 ........ I I
f-g' 1--140 ~ i
........
~ "'"'"I
- 28
I
~-
3
Q) f-Q 1--120 I~
::J ~
o 0
" """ ""l'-..
CD ~
f-~ 1-100
I\) l=
"-
~
o 20 I ~
80
::0 I--- I=--
- .",
--
"'0
;: 60
~ -
Ci1 ~~
40
<:5
w
20
I
g
W i i
0 2 4 6 8 10 12 14 18 20 22 24
I Ii, lt
l---- Altitude X 11000 Frt
Ii
:~ , :" " " " '" " '" fR""" ,' ' ' ' '" " '"' " '" ' ,m "'"''''
.. ,
......
cp
o
?I\)
CD
-..J
cp
o l fill fffIII
! I
?w I !
o =
= 1 I I I
= 220 I 1
:: I , I I
40 IN. HG. MANIFOLD PRESSURE I
I I
200
38
~
36 I
~ I
180
:::= 34 ~........ !
r-- ..........
» ::= 160 32 I
;::;:
= =
~ OJ
C ::: Ql
30 '"
Q.
(II =
",I-- 7'
(!)
f--140 28
"tJ :: I
(II ~
:::
::I.
= ..,0 26
'"
o.., = ~
:::1-- '8 -r-120 ~
3
Q) ... ~ 24
(!)
::J .., i
(') r-
(II
N
100
en -
o I
o
JJ 80
"tJ
s: NOTE:
~ 1. FULL RICH MIXTURE 75% POWE R AND ABOVE.
60 BEST POWER MIXTURE BELOW 75% POWER. -
2.
9w :: 3. CORRECT BHP FOR INLET AI R TEMPE RATURE AS
FOLLOWS:
~
C)
40 -
a. ADD 1% FOR EACH 6° F. BELOW Ts.
III
b. SUBTRACT 1% FOR EACH 6 0 F. ABOVE Ts.
= 20 I
::: ,
:::
::
-= I I I
= 0 2 4 6 8 1'0 12 14 18 20 2'2 24
::= ! I i
-~ Altitude X 1000 Feet 1
!
I
-== , I I I I I
1111111111 ,111111111 111111111 11111111111 1111I11111 11111 11111 U1WillIIHIIJIllII
~ "'" I I II ~~_____! I!
220 40 IN. HG. MiNI FOLD PRESSURE ' J I
:::= ! I I
- 38 I !! I
:::=
:- 200 ' """ I
::::: 36 -~
:: b-.
::: 180
- 3 4 L """
:::
»
::;:
:::
;::;: = 32 I
ii '
""
C
::
0.
160 - 30
(I)
-::: OJ
"'D 28
(I) ~
§:::_<t>_ ~
:::s. :: I
!---140
:: 0 26
o...
3 :: -.. - I"'"" I '
Q) :: ~
::l ::_ u '-120 24 .
o(I) :: 0
::: ~
N :: ~
.....
o
o
-::: 100
-
-------- I
:II
=
:::
"'D :: I I
I !
:s: ::: 80
-f ::
en ::= NOTE:
I 1. FULL RICH MIXTURE 75% POWER AND ABOVE.
ow :::
m 60 2. BEST POWER MIXTURE BELOW 75% POWER. -
<? :::::
G) :: I 3. CORRECT BHP FOR INLET AIR TEMPERATURE AS
OJ ::: FOLLOWS: __
40
= a. ADD 1% FOR EACH 6° F. BELOW Ts.
:::: b. SUBTRACT 1% FOR EACH 60 F. ABOVE Ts.
-::::::: 20 I
:::
:::
::: I
::: 0 2 4 6 8 10 12 14I 18 20 22 24
:::
:: I 11
I I I I
.. 1
-~ Altitude X 1000 Feet
~
o I
L. _______
<?
~ I I I I I
w
....
.....
!p
o I I
<? I !
~ I I
NOTE: TYPICAL INSTALLED PERFORMANCE
(SUBJECT TO INSTALLATION EFFECTS.)
220 I
I I I I !
(') 200 ?~t:.SS\.l~t:.-----~ .?) i_
....;:::II
~ 180 1\0
"G.>A~~--
\~ . .:::::.:-< ~
i ~
~ ~.?8Q
»
;::;:'
;:::II V- ~ ~ ~ ~
a
CD 160
Kr--. ~~ ~~Qv .~_ I .
~ ""
m I-~- f-140
"~~t"- "~I "~
::J ~
--....~ ~
tl)
(Q
A
('()
S' " ~ ~'~~
CD I
(J) I- S;-
VI
"" '" I
-g ('()
~120 I--- ""
-0
~~ ~ ~oo~ ~
[ 0
:l!
I-~ - f-100 ~r--.. ~Joo ~ I , , ' "
~::J
Q. 1
I»
"'~ ~o ~"" ~~ ""I~I'\
a
~ 80 " " I "" "'i
:s 60 ~ Nl ",i
u1 ,
I~ , ""l "'-, ,
~
5 I
I1 ,
~
II
lJ
~G") 40 ~ """, '\ I
OJ
20 1 1 ,
o 2 4 6 8 10 12 14 16 18 20 22 24
I ~ I ! i i i I I I
r Altitude X 1000 Feet---t :
I I I : I
I II I
I ,' II I:
H---+ NOTE: 210
1) Sea level horsepower correction
a) Add 1% for each 6°F Below 60°F
b) Subtract 1% for each 6°F Above 60°F
200
170
MA
ex::
160 LU
CR ISE
$:
0
0..
150 LU
(/)
ex::
0
DED I
140 LU
~
«
ex::
130 co
120
110
100
90
G RA GE
80
70
20 22 24 26 28 30 32 34 36 38 40
MANIFOLD PRESSURE (IN. HG.)
76-00-33
"'-!
cp
o
C?
W
::::
.1:0
:: 140
= ~
=
:: / 130
::
=
= /
/Jfl
= 120
= V /
:::=
:: /v~y 110
= I' v~
:::
." ::= ~oq 100
C
!!. =
:: Approximate Best
." Power Cruise - V ~~ c
"
--
/ ~ !!.
~ 90
~ 7'
fl>7 0
"
c;3 ::i!
",,"
OJ
\ /~ ~\ 80 r
::t cr
!"
"tJ ~\,~? ~ - - - Minimum Allowable
::I:
--
u1 / - ,. ~ Fuel Limit :"
70
9w / /' 80%
~ ./ ~/ .."./ ~D.I I 75%
~::t
= 60
::t
:i ~S~ , / .",.... r' T
OJ ~ / ~Jt'"~~c,~ \70%
~ - ~~ 65% 50
j ~,..::::::e,a;:o",~1' I \ '---500 FR;chofPeakEGT
~~~ ~~~·~I 55%
40
~,,,.,,,, - I '--Peak EGT
~~~ 45%_ I 30
20
50 70 90 110 130 150 170 190 210
Brake Horsepower
1=
35 FULL THROTTLE
ci
::t: 33
E
V
Z
~ 31 /'
V
w
a: V
o~y
~
Z 29 v 220
<
:E
>-
a:
~~
./ .d
0 27 200
V
V ~/
v)
co ~
< .".. ~~
25 ~~~~ 180 a:
w
~'P / V
~
0
~
LU
160 a:
en
/' V 0
'/ rJY
::t:
/ 100
ex:
::t:
"
;::
/"
/
~
.650 80
-
::t:
co
~
..J
.600
~ ~LTH
-....!!2~E -"'1
v)
z
0
U V
-
.550 ./
..J
.
w
:::l
c.,j .500
,PROP LOAD_ ~
V
w
~
en
.450
76-00-35
MAX ALLO VABLE
1\1AN FOLD PRESS )RE - 7 210
jY
'1,<0
~
/ 200
V
/ 19" 190
// ~ 180
/ IIV ~~ 'k
~C5
170
IIVI / ~
f-
160 a:
/ VIV/V ~~
w
3:
150 ~
V/VIV V/ ~
Cf.)
a:
o
:r:
~ ~ 140 w
;jV/; ~V/V/ ~
~
-t
-~~
a:
m
130
Ih ~'II ~ ~V 90
1Ih~ ~ /~V 80
'II! ~ /~ /' 70
10 ~/ ~
LftlRi 60
18 20 22 24 26 28 30 32 34 36
76-00-36
,-----~ r---- T-----.---r-- r- --
l=
2200 RPM l-
t-
J l-
t-
te
-te-
e::
L
150 t:
l::::
140 c
30 In. Hg. Manifold Pressure
III t::
:IJ
~ » 130
:tA 28
C'm
g. J: 120
.,,0 26
3.~ 110 ..
Qm 24 :-c
-
~ (3 100
g~ -
22 ::c
~ ~
f\)
90 :=:
f\)
!==
g 80 20 t=
JJ -
."
~ ==
3: 70 :c:
~ c=
is
I
60
W ~
J:-,
0)
? ~
::t
:t:
o:J
tOO +60
t::::' +40
+40
~
Q. +20 +20
::;
w 0 o
>--
>-' ·20 -20
-'
<(
ci -40 -40
r-
<I)
-00 -00
-..J
cp
0
II I I 1IIIIIIIIIIIIIIIIIIIIIIIIPlt
-' 2 3 6 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
0
~ PRESSURE ALTITUDE IN THOUSANDS· FEET
I Lli
W <I)
-..J
"'-l
Cf>
o f--
o,
w 2jOO ~PrJ, l:=:
()O
1---
150
30 In. HQ. Manifold Pressure
140
» 28 I-- r--
~ ffi 130 r-
g- ~ 26
"tJ 0 120
(!) a.
::l. w 24
~ ~ 110 I-- -
l--
~ 0 -
g J: 100
II) w
- ~ 90 -22
~ <£
o 0: ----
o co -
:::c 80 20
"tJ
s:: V
-I 70 ./'"
U)
<;>
w
m 60
~/
---
0
,
:I:
:I:
OJ -
+60 +60
t::': +40 +40
\!-
Ii +20 +20
::;
W o
I- 0
':i -20 ·20
-40
..
ci
I-
-40
<f) I11111111111111 -00
-00
2 6 8 9 10 11 12 13 14
J
15 16 17 18
IJ1;lllllltlll 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
~
. .
E=-
c'
..
170
32 In. Hg. Manifold Pressure
160
»
:::;: 30
;:;: i--
c: 150 - r--
0-
(I) 28
"'00:: - r-- I"-
(l)w 140
r-
B-3= 130 26 -
30
Q)Q.
:lw
goo 120 24
--
Q)CC
;:;0 110
~:c:
-
ow
::tl::IC: 100 22
"'0«
5: cc -
(rim 90
0I
20
W i
C» 80 ~~--
0,
::I:
::I: 70
00
+60 tOO
t::: +40 +40
!i-
0: +20 +20
::;
w 0 o
>-
,...: ·20 ·20
:;J
"'-J c:i -40 ·40
C{l >-
(/)
-60 -60
0
0
W
I
II
~
-'
I I I I I I I I I I I I I I I I II LI
2 3 5 6 9 10 11 12 13 14 15 16 17
co ili
(/)
-.,j
cp
o
oI I I I
.1:>0 t=
o 2500 RPM f:
r
rc
--
.~
180
-
32 In. Hq. Manifold Pressure
:!> 170
;::;:
;:;: 30
t:
a. 160
Cb
-... r--- ' -
"'tI 28 '-
Cb -
::J. 150
to
....0 ::0
3
D)
l> -140 26
:l
0 m
Cb "
D) :t 130
I \)
- 0
c.n ::0 24
0 (J) 120
0
:0
m
"'tI "1J
s:: 0 110 22
-i :E
en m
0I ::0 100
W
0> 20
0, 90
;:x: i.----
1"""-
:::x: -_._-
III 80 ---- - - - -- - '--'-- -
+60 +60
t::: t40 + 40
!!-
0.. +20 +20
::;;
w 0 o
>-
,.: -20 -20
...J
..
0
....
·40 ·40
(/) -00
-00
II I I I I I I II 1111111111111 LLUdrn±t1l
2 3 5 6. 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
::::.-
t:':
200
34 In. Hg. Manifold Pressure
190 :::
::::
=:::
32
180 r--
r--
- - ~
l>
30 r--- r-- I - -
r-I - --
::+
0::
;:;:
c:
Co
w 170
~ 28
- -- r- r--
(l)
0 160
"'0 0- 1-'
(l)
:::l.
w
0 (/) 150
... 0:: 26
- r- -
I-:
0 l=
3til
::I J: 140
0
(l)
til
W
~ 24
- t::c
-I\) <t 130
en
0
0:: t:
I==:
0 00 I==:
::IJ 120 r=
"'0 22
s: F:=
-f 110
en F
(5 t:
I
c-
W
100 :=
en 20 F
i=:
0I I-- -
::r: 90 ._-- r=
c
:x:OJ -- E
r=
L........ _ _ _ t:
. L ... -~.- ...
80 -- - ---" .. ... -
+60 +60
to +40 +40
~
"- +20 +20
::;;
w 0 o
>-
>j -20 -20
..
ci -40 -40
>-
<J)
...... -60
11111111111111111111111111 t l -60
~ -' 2 3 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
0
0
w
~
~ PRESSURE ALTITUDE IN THOUSANDS - FEET
UJI
~ L5
<J)
....•
.....,
t{l
0 l
0 ~
I 2700 RPM
.s:. i=
F=
I\) I I I
210 ~
~
34 In. H~. Manifold Pressure f-
f-C'
f-
200 ::::
32 t-- I---
190
r-- I--- =
=
r-- r-- J=
~
- t=
30 I--- I-- I-- F=
180 I='
t:c
r-- f--
» r-- I--- t---
5 ffi 170 28 - - -
a;;
C'D 10-
~2 160
- - '-
::l.u.: 26
"-
~ ~ 150
:::I _
mo
O..i. 140 24 lj
:LL r--
-~
~ <l 130 -
00:
Oil. - ~
::tJ 120 22
"tJ -=.
s: f....-- !---- -
-I
en 110
--
0I 20 >--
W 100 ..-
en ;;of..-- -
<?
;t -- -
::t 90
OJ
-
--
+60 + 60
t:: +40 +40
!f-
a. +20 +20
::;;
w 0 o
I-
~ -20 -20
..
e -40 -40
en -60 1111111111111111111111111111111 -60
-' 6 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
220 -
34.5 In. Hq. Manifold Pressure
210
34
200 r--
32 - -- - r- r-- r- r- r-
» 30 r-- "- r- t-- t-.
190 -- l"""- t--
SIIJ r-
g~ 180
"'O~
28 - r- r-
tOm
g::r: 170
0 - I-
3 26 .
1»:tJ
::IC/)
160
gm r--
j
S (3 150
24 I
~:E r--
g m 140
::1j:tJ
"'0
.
;: 130
.... 22
u; ~
C 120 !-- ~
I
CN
0'1
0
•
::t 110
::t
aJ
.60 t 60
t::' t 40 , 40
~
n. t 20 ,20
::i
w 0 o
0-
,..: -20
---' -20
« -40
0 -40
I-
(J)
-00 11111111111111111111111H4lllm -00
--J
---' 5 6 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
'(l
0 ~ PRESSURE ALTITUDE IN THOUSANDS - FEET
0I «
w
J:>o (J)
CN
(J)
I
"o
oI
.j::o
.j::o
E::
150 E
t=
t=
t=
/ t=
140 ~
f=
f=
f=
V / 130 ~
t==
E
/' ~
/' /
/'
120-==
." V ~<Q =
=
t:
V 110-~
:-::
~
." =
~
/'
V ~p~~~~
/'
f' l00-~ ""Tl
~ -<.~~V f= C
t== C1l
<
(J) APPROXIMATE BEST POWER CRUISE- V §:
./ A ""Tl
OJ
9O-t:::
t= o
:::x: ./" t= ~
t=
" V"
"tI
~ t:::
8O-t::: r
\vY- , . / CT
t= VI
~ V\ \)\-\-~/ t=
V ~........
t= f= ---I
/'"
9w V
(J) 70- E
V ,. ". !=
~ / K f=
OJ ........
V V' ... ~ 75% f=
, 6O'r-~
V "'-
1/ ... ~ ."",... MINIMUM ALLOWABLE t:::
FUEL LIMIT'
t=
\)\S~ I;- 65% ~
"..,
V V ...... ~('\
\ 5O-f=
V C~r:::: ~:... ~ t=
f=
I t=
V V ..,-::$~ 55% \\ 50 0 F RICH OF PEAK EGT f=
4O-f=
~ ·~tJ~ t:::
,/ F
f=
........
~CO 45% PEAK EGT~ f=
30-::.=
"" =
=
20-~
=
t= t=
~ 40 60 80 100 120 140 160 180 200 220 J:::
111111111111111 III 11111111111111111111 1111111111111111111 11111111111111111111 1111111111111111111 11111111111111111111 11111111111111111111 1111111111111111111 111111111111111
Brake Horsepower
Ii !l iillllll! 111111111 11111 Ll
~
~
=
=
~
~
FULLTHROTTLEADMP
36
~ 34
/
Z :::t I
I
:
V ,,
:=
~ 32
w
c::
~
Z 30
~
=-=i
h
I
I
I I
I
I
I
I
I
: ! !
'
!
!
,
I
I
'
I
I Y
'/I-j--
I I
I
I
I
I
I
~:
1- 240
~
i I ~
« I I
: i .' I ~
:aE
~ 28 i===
o E
I
I
iI I
I
-b' f>.O~~/ i ......,
I
I
, 220
en E of>.° / " "/
t==
~ 26 f=
~~ ~ ~
c::
w
200 :::
1=
1=
1= ~
V
~~ «:.~
~"'\\- /
/ o
~
w
180~
/.
24 1= ~~,<,o
1= o
1=
;:::::
[::
~\-\-
/
/ I
I
:J:
w
160~
= V «
=
= / c::
::::
~
L ~
'X-~ / 140
OJ
::::
~
::::
o~
'v0 sjP t= 120
~
::::
~
::::
jY ],
/' 100
=
= v
.. 75
=
:::: / 80
c:: ::::
--iii
:J:
~
.70
t= ~~OP
-- t::
E I (04D
~ r:-
--
(/)
OJ
~.65
=
= FULL THROTTLE BSFC
(/)
z ~ ~
o =
.60 :::::
==
(.)
..J
w :::
:::::
:::l
u. =
cJ ::::
:::
w
~
(/)
=
=
::::
=
~
I
ENGINE RPM
76-00-46
11111 1111II1I11 1111II11I1 1111111111 II11I1111 111I11I111 1IIIIIIll II LUll 11 I 111111111 1IIIIIUIl UIII 1111 111111111 11111
I I I I I
p- -F
F
I- F
;-
F ~
230
t= I-
-~
=
=
- ./
/ ~
~
220
=
~/
= ~
-~
=
= F
- ~~ F 210
=
= R>~ F
f-
= tV -f=:
=
- / F
f=:
~ F 200
t=
t=
~
I--
~
/ ~
/ F
F
f=:
I-
190
~
F
~
~
~
r-
f=
/ /
-F
f=:
~
r= 180
~
~
t=
r-
F
/
/ V / -F
f=:
F
F 170
t=
~
F
r-
vY V.
I / "/
~
;-
-f=:
=
f=:
F 160 0~
w
a:
I
/ L V //
f=:
t= V ;-
= -t::: Q.
f::: w
~
- ~c::s
~
150 en
a:
-="""
~ ~
1=
F
t=
II / I
I /
'},'P
/
/1
r=
.f=
r= 140
0
J:
w
~
<
!=
/
/ v/ / V
:::: f- a:
-~
= CD
= ,s.'Y 1=
f= 130
;r
'-
= f=
I /'
F
t=
==
=
II / / / / /' t-
-F
!=
F 120
f=:
::::
::::
::::
:---
F
I I V V/ / / ~
f:::
f=
l-
t:::
110
~
-
/1 I / I /' F
"
~ f=:
I=::::
l- / !=
f-
f=: 100
I II V V /
!=
t= !=
!=
t:::::
F
r- F
I-
1= != 90
~
t= I-
1=
1= II / / IV / !=
F
!=
f-
!= 80
~
~
f:= I-
=
-
::::
II / / / !=
=
==
= 70
-
='- l
/, 11/ / ,/V , 1 , 1 I I I I I ==
11111 111111111 1IIIIn II.. III lIT III 1111111111 111111111 111111111 111111111 111111111 111111111 111111111 111111111 11111 60
18 20 22 24 26 28 30 32 34 36 38
ASS. DRY MANIFOLD PRESSURE IN. HG.
76-00-45
IIII 1llllllllllllllllllllIllll'llllllllllllllllll"ll 11111111 ,,"IIIIIIIIIIIIII!1I1111111 11111
=r
I I I I I I I I
=
::: BRAKE HORSEPOWER ==
=
1= 0
I 0
I 0
I =
~
1=
1= 0
~
0
M N .... 0 0 i.i~~
6
SZ f=
f=
f- .... .... .... .... .... Cf) , , - r--
~=
=
\ \ ~
Cj----~--~~----f_----~~--~--~+-----~----+---~~--o~---+~
\ \ \; F
f=
- I I I '--
ilill 1111111 I 1IIIIIllIIIIIIIIIIlIIIIIIIII 11111111 Ililllli 111111111 I111I111I ILlllllllllll1
76-00-47
L1111111111111 IIIIIIIIIIIIIIIIIIUIIIIIIIII 11111111111111111111111 111111 111111111 I1111111 1111U
~ I I I I I l==
~ S
~ BRAKE HORSEPOWER ~
~ , . I t:=:
t:=
t~ ....~ ~
0 0
~
0
:: 0
;: 0
en
0
co g
0
co t:=
~ t:=:
~ ~
~ ~
~ t:=:
II
f- 0 i":-
r-~~ N
~
t:=
~
~
f-
~
~
~
~
I co
b
f--
~
t:=:
b
~
~ I .... t:=:
~
~
b ~
~
f-
~ r-
W-b
~ w F
tl- L.L. ~
~ 8o-F~
r-~ ........
N
F=
~ x F=
~ ~
~
t-r--+-_-+-_ cr.
w 1 W
0- ~
F
~
~
t-::
~
C/)
C/)
\ ~
~ F
F
f-
~I-'-
1--+--1--
W
cr.
~
co -;!- t:::=
t=
\=
§ 9
0..
\ \ \
I<t:F~
~ 0 ~
§~
~
~~<t: II
\ ~
~
\ \ ~
~
+4---~---_+--_++---~--+-~--~~--~---~r---~
Ie ~ \ ~ \ \ \ ~
I
~
~
~ ~ \ ~\ ~\ ~~ i",o ~
b~
I--'- I I 1 J ~J'-
11111111111111 IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIJI 1111111111111111111111111111111111 Uli!
76-00-48
1:111 111111111 ' 111111111 1111111111 illllllli II Illllll i Illllllll 1l1111UJl IllHUJU IlI!lUll lIULLU.! TUI1
- 1
1 1 1 I I I I I I
',-
= 1=
= f...-
= BRAKE
, HORSEPOWER
, , 1=
= 1=
= 0
(Q ~ ~ 0 0 0
..- g 0 0 1=
-= ..- ..- ..- M
..- N
..- ..- ..- Ol co R 1=
>--
=
=
1=
1=
= I, 1=
:: 0 1=
f...-
= N
r=r=
I
=
=
=
-
=
I! I 1=
r=f...-
II
l=
=
-
~ I ....
(Q
r=
t=
r=f...-
= I r=r=
=
-
-==
=
I 1--1=
1=
1:::
~
I
UJ
=
=
UJ
u..
1=
1=
=
-
::::
UJ
a::
o 1=
.... 8-~
N
::> I ..- 1=
i= en f-
1= en X 1=
f...-
~ UJ
a:: UJ 1=
l=:: Q. 0-;:::
r=- 0
I ::> l=::
1= ...J
I- -1=
- i=
t= 0
u.. \ I- f...-
...J-1=
i= - 00
<t i=
1=
l=::
1=
::::
z
<t
~ \ \ \
1=
1=
~
=
=
\ \ \ =
(,')
::::
~:
J:
=
;:::::
-
i= -
Z
~
f...-
;:::::
~\ ~\
1= 1=
~
0 0 0 ~ 0
f--
1= N ci cO (Q N 1=
- M M N N N I ~
'-
i=
\ =
1=
1=
~
r-
1=
f...-
\ \ \ ~ 0
i=
I=-
f::::
f::::
1:=
1 1"-
111l 1111111111 I111111111 illllllill 11111111 111111111 111111111 IIUIIIII 1111111 1I1I11111 111I11I fl III! 1
76-00-49
1111111111111 11111111111111111111111111111111 r 1111 r 1111111 ! I 111111111 11111111111111111111 111.1
I=r I ' I I I' " -1==
~ BRAKE HORSEPOWER ~
~ ~ 1 I ~
~- g R <0 f5 ~ g ~ ~ 1=
1= .... .... .... .... .... ... ....... ~
1= ~
1= ~
1= ~
~ 0 ~
1= / ',' I I !==
_~
1=
1= I N
=
~
~
1=
1=
I I / ~
_~
~
1=
i- I ~ --t=
=
I=r-.
t:
~
/ / I ~-~
t
!==
~t-
1= / /1 ~ ~
w!==
E=
I .. . .
1= w 0
~t-a:: 8-F=
1=
t=r-. ::;)
1= w
~ I N
x ~
w E=
I=:
~~a:: o-~
1=
f-
~~ "
0../
~
I ::;)1=:
~ ;::::
~
1=' ....I ~ 1=
~f-~ co ~-~
1= - <! ~
1= z _1=
1= <! 1=
t= :?! \ 1=
I=t-. \ r
rr-. ~
1=__
~
',: E
-~
1=
1= z. \ : : : :::
I=t-
1=0000 0 \ 0 \ ~
I=r-.. N ci o:S (t) ~ ci
~ ~ M M N N \ N '"
Fi~_+__
:::
4--_+-_ _ +--L-._+-_\-'--l-__f-I\-'-_-+-_--L\+--_ 01---+-1 1
~
~ , ~
1111111111111111111111111111111111111111I111111111111111111111111 111111111 1111111I II1111111 11111
76-00-50
1111111111111111111111111111111111III ITTTTTTmmmrrrnlll·llll11111111 111111111 11111111 111111111' [!lUI
1= 1 T i l I I J f T T ' I _1=
t= BRAKE HORSEPC WER !=
76-00-51
11111 111111111 1111111111 111111111 1IIIITITTfTTfTTTTTfTTmmTTIllTllllllli 11111I11 IIj III
1=
I
I I I 1 1 F
t= BRAKE HORSEPOWER 1= I-
1=
~
==
F
F
...
0
N
0
0
N ...
0
en i... 0
"
.-
I I
0
co
.-
I
...
~ i 0
...
CO)
...
0
N ......
0
1=
t=
1=
f:::
I-:
f:::
f:::
F f:::
f:::
==
:::: ~- f:::
F
iF
t: / 1/ 1/
/ 7 I I t=
f:::
f:::
~
t=
/ / II
F
::::
F / I f:::
f:::
f:::
== ~-- 1==
I=:
==
1=
~
1=
I / / / f:::
1==
~
I-
~
~
~!-a:
1=
w / / I I I
....
wl==
wl==
Nu..1==
.... 1==
1==
II I
::::l
I-- en gl=
~t-
~ w
en
.... 1=
1==
I=I--a: X~
1= Q. I wl=
~t- 0
t=
I--
..J
0
t=1--u..
F _
I \ Ot=
::>1=:
co!::1=
1=
.... t=
F
F
== ::E.
::;:!-
::;:
F
Z
.:t
c.?
::t
\ \
..Jf:::
«f:::
t=
t:=
1==
F • t=
-F ! -Z- ~ I=:
,
:::: o:r--t:::
f=
F
F
==
0
cd
CO)
0
~
0
N
CO)
0
0
CO)
0
cO
N ~\
0
.,j
N \ 0
N
N
\ f:: f-:-
1=
F
F
F
~
r=r=
\
, \ \
t=
I=:
t::
t=
o--l==
~=
1--. E
1
11111 I111111111 I111111111 1111111111 1IIIIIllli ITlTTTTTTI rTITlIlTTl IlllIIIIII I llllllill 111111111 11111111 111111
76-00-52
I1111 1111111111 11II : 11111 I11I111111 11111111 i II111111111 Iill III III 1111111111 1111111111 Illlllllll III 1"111111 I111111111 I11I111111 111111
~ -,-
~ - ~
f= 37.0 IN. HG. MANIFOLD PRESSURE 230
::::: ~
:= -f=
S 36.0 f=
""--- 220 f=
f= -
:= .,,""--- ~
:= 34.0 -f=
r--- r--..
f=
l> == 210 ~
r--- t-- r--..
::;: :=
;:;:
c
a.
(I)
:=
=
32.0
- ""--- r---
--- t--
~
~
~
~
-f=
== 200
(I)
i= --...... f=
" ~ ~
s-...
3
~
f= 30.0
--- t---... J:)_~
f=
III ~
Q)
f= --......... 190- »
~ f= ~
:I ~
------- m f=
(')
(I) ~
f- ~ :r: f=
180- O-f=
~ ~ ~ J:) ~
o ~ 28.0 (I) ~
- ---
o ~ m ~
l] ~
-.... 170- ~-t:
"s: f= ~ :::
f= m :=
~
~ J:) =
Ci1 ::--- 26.0
160 =
9
Co)
m
=
=
= ~ -
--- =
:=
=
9
c.. == 150 ==
:=
----
CD ::::
=
f= :=
=
~ ./
~ -=
--- 140
=
:= V'" ==
----
:= -:::
S 0 4 8 12 16 20 =
:::: :=
:::: AL TltUDE X 1000 FEET :=
~, 1-
I I I
11111 1111111111 1111111111 illllllill 1111111 : 11111111111111111111111111111111 ,J 11111111 1111111111 111111111 lllllillil [llllillll IUIIl
.....
<p
o
9
U1
w
111111111111111111111111 IllJ 11111111111 i III I1I1
I I
~ E
~ t5 t=:
f= Z f=
t:::
F=
«
:2
~
F=
~ a: ~
= 0 ~-+----~----+-----~--~-----+----~----+---~-----+----~----+---+c~
= I.l...u
a:w
c
t:::
~ w~ ~
~ w -+----~----+_----r_--~-----+----~----+----1----_+----~----+_--+f=~
==
= OC
w.Q
f=
f=
== ~~
«
f=
~-00 _+----~----+-----r_--~-----+----~----+---~----_+----1_----+_--~
~
=
=
=
~oo
~C
Z·-
f=
F
F
= - 2 _+----4-----+_----~--~~---b----~r---hr---1----_+--~~ ~~--~~~
i I ~ II , ///V /v / /v ~ N
2
~
~
~~
ill
i
I
I
iQ~;:
V/ / /
/ / /
-+----~----~~---~--~~--_+~--~~--+_--~--~_+----~~~---4~
/ /
~ I ~
F=+--r---+----,f-/--j'/~ t;-\S
~~~~~~~~~
~
v / / V
9.~ -t/4--i---fl---+---A---+---+--~ ~
~
=
::::
~
/
<§
~
~
~
~
'"
~ / <0
- ~
w
w
t-~+---t----i---hl\"--/-+-/-+-I-lr-~ f---r_.-~-~-+/+--+---f---+-~+: ~:~~~:~: §
I
F1=t---+-----+----+
~/
«;'<U,\ /
Y V/ 'II ~ ~---t_i ~
-i
I-I+-__+-___ +-_~----~_+t~ / / : ~:~~~::
I ~ /
I-~+---+----+----I--+-- ~~~I---+---+I-+---+-·--f---+---+---+---t- <0
/
F ~
~ /
t-~+---+----+----f----+----~o~~\-1----+I/r---~---+---if----+-----r----+~~--+-i
t:::
E.--+-----+_----f_--_+----_r----~----r_--_ir---_+----~----+_----f_-_;_
t-'+- N~-_+_i
f=:
f=:
F=
~
1\
Et---+----+----1-----+-----~--_+--~~----~----+_--~----_+----~----+_ ~-1--~~
~
~
r-
0
N
0
0
0
co
0
<0
0
~
0
N
0
0
0
co
0
<0
0
"'<t
o~
N
E
,-
F= N N ,..... ,..... ,..... ,..... .... t:::
~ ~
f=:
F I
IIII1 I111I1111 1IIIIIIIIIIIIIIIIIIlIILUIli 11111111 UIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII 1IIIIUll jllil
BRAKE HORSEPOWER
76-00-54
LLI I I I II I I I III I til 1II 1II Illl11LlL1 !LlllIUII IIIIIIIIII IIIIIIIIII 1IIIIIIlii I I I II II II 111IIII11I I I I IllIll III II I I II 11111111 I I III1111III IIIII
I I
F= F
~ ~
1= ~
1= ~
F= AVGAS 75°F ~
~ ~
1= ~
F= F
F= t:::
~ ~
F= t:::
~
==
:::: ~
:::: ~
:::: ~
~
==
== ~
;= ~
F=
F=
F=
300
~
F=
F=
/ F=
~
V F=
F=
F=
250
/ f=
1=
./'
/ F=
F=
~
F= '/ 1=
F= 1=
F=
f=
~ 200
/' f=
t-=
a:: F= MAXIMUM PRESSURE DROP ALLOWABLE F=
I 1=
'-
ci;
F=
f= / ACCROSS A SUITABLE FLOW TRANSDUCER. F=
f=
F=
ro F=
....J
~
E
~
o....J F=
150
/ F=
F=
E
I=-
u.. 1=
1=
....J
W
~
:::
F=
/
/ ~
F
~
t=
1=
u.. !:::
t-=
;:::
;= 100 / F=
f=
1=
F=
F=
t-=
==
V 1=
F=
~
t-= F=
1=
::::
F=
== 50
F=
I F=
F=
~
t:::
F=
F=
f=
:::
/'/ ~
F
f=
1=
F=
==
== F=
::::- 0 ~
==
:::: 1=
;::: F=
0 .5 1.0 1.5 2.0 2.5 3.0 3.5':. 4.0 4.5 5.0 5.5 6.0 6.5 F=
==
E ~
F= t-=
F= E
II III
PRESSURE DROP - P.S,I.
76-00-55
::
::
FUEL INJECTION PUMP INLET PRESSURE REOUIREMENTS
60 l-
./
V ::
'/
V \~~
~,?-'i>-~~~
V
~ O~ ~ ./: =
~\~ ~\O~
w
a:
:>
II)
II)
w ./
V ~\
~,?-~O· ~.§
~~I>'~~~C.VV
,,' ./
a: 40
Co I'" 0<;;'''.> V
/ V
30
!=
J
/
./
V
V
~ V./V ~
10 /
MINIMUM ALLOWABLE
L 1 1
- /
20 40 60 80 100
IDLE
PERCENT·RATED POWER
76-00-56
111111 111111111 1111111111 1111111111 I I I I I I I Iff I j j j 11111 111111
t= F
1= 1=
1= 1=
1= 1=
t: t:
t= ~
1= NOTE: ~
t= t==
t==
t:
t= 1. EJECTOR PIN 642955 ~
t: 2. VAPOR RETURN OUTLET PRESSURE 1=
t=
1= 3.5 PSIG
1=
E
1= 3. INLET TO PUMP - 2.5 PSIG
~
1= 1=
1=
t: 4. AVGAS @ 84°F.
t= 1=
1= ~
1=
1= NOTE: TYPICAL PERFORMANCE I 1=
1=
1= (Performance is subject to 1=
1= installation effects) 1=
t:
1=
~
E
1=
1=
1=
~r-60
1=
1=
/
==
=
== / V
/
1=
t=
~
t:
f--
1=
5O
/ [7
/
t=
t:
~
t:
t=
t:
~ / / 1=
~
~
0~/ / E
t==
~
t==-40
~~ S~~>, /
~
t=
1= E
1= t==
E= ~
~ / ~~ ~
~
t=1-
1=
~f-30
,/ P E
~
t:
t:
t= V / t=
1=
1= /' ~
t:
1=
t:
V
V t=
t=
t=
~t- 20
1=
/ ./
j:::::
~
1=
E 1=
F t==
1= ~
t=
I=t-
1=
E
j:::
~ ~
~!-10 t=
t: t=
1= 1=
1=
1= ~
~ 40 50 60 70 80 90 100 t:
t=
t:!- 1=
1=
1= ~
1= t:
F'- 1=
lllllll Ifm rn
VAPOR RETURN FUEL FLOW - Lbs'/Hr.
76-00-57
WlIUllllllllllllllUllJllllUlllllllllllllllllllllll11111111111111111111111111111111111111 11111111 11111111.11111111111111111;111'111II
I
-=::::::==
::::::
r=
F -~
=
E
F =
E DEPICTION OF VARIATION OF MANIFOLD PRESSURE CRITICAL ALTITUDE AS =
~ AFFECTED BY AMBIENT TEMPERATURE. ~
~
Fr=+----1
==
(DEPENDENT ON FLIGHT TESTS CONDUCTED TO IDENTICAL PROCEDURES AND --+------:=--;
E
F CONFIGURATION.) .t=:: --::=
F~+----1 NOTE: TYPICAL PERFORMANCE (Performance subject to installation effects.) =::
~5 ~ I I I I i I I ~
ffi~~ I I I II II·_~
~~= i i ==
~hl~_
<C~==_
I II Ii i §1S=
(f)(f)
~ LU
00=
=- +2 '-
~
I~=
F-
FF
~S~
c
~
=-
==
o~~
~~
~~~
-~ ~-+1~--~-----t-----~---+-----t-----~---+----~----~---+----~----t-----+---t~
I =
==
==-
FUr= ~
~~~ r-- ~
~ZO~
~ ~r ---r--!
I ~~
~==
LUa: r=f-
ou...~
0 I .:--.
___ I
==
F
~o~~
0 Fe- ----...'
l--.. i
~
I;:::
~~oF
(§ ~ --------~ I I'
§=
<C Z_ f=
Ff- -1 - - - - .____
... ==
_
> f= ~
LU(f)E ~ ~
o<CF I I ~ ~
~ -~ =
~0E
F<CF
:F: :
~a:E I E
<CFF ~
~m Ff--2~--~-----t-----~---+-----t-----+----+----~----~----+----~----t-----+---t~
<C~~ ~
f=e-
U (f) E
-a:~
~O~
E
,--
a: E
U §E
t:::f-
I
~
<C~ ~
I
I
~ -20 -10 0 +10 +20 +30 +40 ~
Er ~
F
f= E
~
~ ~
r=,- j E
1IIIIIIIIIIIIIIIIIIIIIIIIillllllili 11111I111 1111111:1111111111111111111111111111111111111111 11111111111111111 11111111 111111111 JIlIl
AMBIENT TEMPERATURE
of DELTA FROM "Tn STANDARD
76-00-58
1111 1111111
I I I
IIIIIIII!I III!II
1 I
mLmL·:r,~lqJU jill Y
t- I
E
1= I
F
E
1=
1=
~
t=
~ r==
~ f=
E RPM CORRECTION REQUIREMENTS FOR OAT. VARIATIONS t:=
1= F
~ I I I I I~,_~I I I ____.L .- -_.- l::
1= (PRELIMINARY CRITICAL ALTITUDE CHECK STATIC RUN UP AT W.O.T. DETERMINING ~
E ENGINE SPEED REQUIRED TO OBTAIN 40 IN. HG. MAP)
l=
~ f=
f=
~
1=
l=
;=
~ I r==
E
1=
1=
INOTE: TYPICAL PERFORMANCE (Performance subject to installation effects.) f=
l=
f=
t= I I
I I ~
t= t=
! I II 1=
E
i
I f=
t=
;::::
l=
2500 f=
E:
~
f=
1=
t:=
,~ ~
f=
t- 1=
t:.:
~
2400
!~ ~
l=
l=
1=
t= t:=
...
V;;V
t-
I
l- I ==
~
l-
LL
« 2300 I
~V ~
I
(j)
I
~
Z
I
i
I
I 1 ::::
---- t-.
«
ex:
()
~
I-
2200
!
i
i l?( ~ l=
:=
-=
==
~
:=
l'lV
0.. 1=
ex: 1=
l=
1= -
~
~V
l= l=
1= E
l= 1=
~ 2100 ~
F
~V
E l=
E
f=
~V
E
i-
F
l=
2000 / ~
~ 0 20 40 60 80 100
l=
F
t- 1=
- f=
l=
L t:
1I111 111111111 1111111111 I1I11I11II I111111111 IlTrllTlII rrnl11l11 Ilimllll ITrmnll nmm -mnnn rmllm IIIIIIII!I 111111
76-00-59
II 1IIlIllii 1111111111 1111111111 :111111111 1111111111 1111111111 1111111111 111111111 111111111 1111111111 1111111111 11111
I I I I I I
F
~
NOTE: TYPICAL PERFORMANCE t===
~
r-
(Performance is subject to
installation effects)
t=~
~ ~
~
.t=:
F=
E:
t=: 40
FULL THROTTLE ADMP ~
~ t:::
Cf)
F=
E
~ 38 j
/ / 220
I=::
F=
F
f-
~ F=
/ V Vi
Cf)
w
a:: t=:
~
t:::
F=
0... ~ ~
36 210
Q,i~V /
Z ~ F=
~ ~
~ ~
~
/ F=
F=
t=
>- :=
a:: :=
Cl :=
34
O~
~~ / V
200
t:::
F=
F=
(Jj := 32
~'V./ / J 190 ~
co
~ F=
~
:= 30
V
L f(-O
kt~v
!
/<vQj
V
/ 180
F=
F=
f=
I=::
F= a::
=
==
::: /I . O~ I t=
~
w
3:
-?-~ 170
V b~
«
;j 160
I=::
F=
I=::
~
o0...
W
Cf)
a::
V Of
O~ =
= oIw
L 9....J/ 150 ==
== ~
F=
~
F=
~
F=
V 11 140
I=::
1:=
::: a::
==
=
co
~
a:: t=:
~
F=
~
V
/ / 130
=
==
==
=
I
----
0...
I
~
t=:
~ J
V 120
=
=
.80 ==
co t=:
...., =
co t=:
Cf)
...J ~
~
.70
~ / FULL THROTTLE BSFC
110
:::
=
==
--
~ V :::
Cf)
F= V""'"
/ :==
Z t=: ==
o() ~ ~
.60 100 :=
r= ~
V
--- I :::
...J
W
:::::>
u.. /
~P~OP LOAD BSFC =
F
.50 90 F=
() f0-
W
0...
Cf)
:=
/ E
:=
E
f::
:= 2000 2200 2400 2600 . 2800 ~
F=
E
r
~
'~
-
I llHUUJ 111)11 III 111 llllUll 11111111 II11I11II11 111111 III I! 1111 111111111 11111
ENGINE RPM
76-00-60
II II II 111'IllTIllllllllllllllljlllllllllJ 111111111111111 1111I111 II 1IIIIIIIIIIIIIIIIIIIIIlIflii i II 111111111[[llllllllllllllj~lllltLlI qlU~lIUpIll:P:lIlP:lJlPIIIpllIpmpllll;: I [Pllq -1 _
'TI
I tures remain below 420 0 F and oil
temperature does not exceed 200 0 F.
--t-- -t--120-t--------+
t::
~
--f----t--11 0 +------l
'TI
! NOTE: TYPICAL PERFORMANCE
(performance is subject to
~ installation effects.)
vry -+---t------111--100 I 'I
~
i
OJ LV / V l/1
::t
"tJ
/V : / ~0: ~+-- I I 90
I
~ I I 80-+-------F
9
w V /V ~"""'-NOTE3-\ .
m ~
?
OJ RECOMMENDED MAX FULL RICH-V V7 /' ' \ \- I I 70----+--------+
'" I I I I ,,/ ~ ~ ~
F AP~ROXI~ATE ~ULL RI,CH V/, " Vi,;' LOWER LINE I I 60+---.
~APPROXIMATE BEST POWER, ,,~ IS MINIMUM ALLOWABLE
----I--- 50 +------l
§I-MINIMUM 'SPECIFIC ~ FUEL FLOW
FUEL CONSUMPTION p~ I I
f- NOTE 2 40 -p
I ~
S-
~ 100 120 140 160 180 200 220 30-f--- -j --
-.j J I ,I I I I J t I I, I -
?> 1IIIIlliWllllUl.W.illW.ll.L IITIIIJIT HUillllUlllillllllUlllillWJ..l.ll.[[!]JIlilllll m
o
oI BRAKE HORSEPOWER (Propeller Load Curve)
m
....
......
<p
o
oI
~ =
::;;:: 1 I
220 I
:::
NOTE: i I
::::: 11. FULL RICH MIXTURE 75% POWER AND ABOVE.
:: 200
. I 2. BEST POWER MIXTURE BELOW 75% POWER. -
::=
::: 3. CORRECT BHP FOR INLET AIR TEMPERATURE AS
:: I FOLLOWS:
180 -
a. ADD 1% FOR EACH 6 0 F. BELOW Ts.
::=
:: b. SUBTRACT 1% FOR EACH 6 0 F. ABOVE Ts.
1> ::;:: -..-....
;::;: 160 36 IN. HG. MANIFOLD PRESSURE ---
:::;:
t: :::::
Q.
CD
::::
-- ~~
"tI =1- g:'- "-140
= OJ 32
~ ~ I- ~
I
~... ~
3
I\)
::1-°_ ~
:s::
= Vl "-120
ro I
L--- ~ ~
~
g :::: -g~
I\)
I\) ~~cti-
;::..., 1-100
o ~~
o =
::: '~
:IJ
~
"tI ~
80
3: ~
I
~
~~ I l"-
60
~en
~
~ 40 ..... - ~ I- - ...- I
'" I 1
I
IXJ :: I
" :::: i !
20 .
=
Ii
::=
= I
0 2 4 6 8 10 12 14 1~ 18 20 22 24
I I
I I I I i I II
!---Altitude X 1000 Feet
·r~
F I I I I I
1111 1JllllllillmnmnTTlIIII 1IIIIIlfTmm 1IIIIIIIIIIIIIIIIInlnnrTflllii 111111111 JTTTTTTIT mm III 1I11111fT mmrr "" II" 11111 11111111,11111 111111111 IIlmn! 111111
f- r I T I I
~
-1=
I:::::
~
-~
~
I:::::
~
-I:::::
~
190 NOTE: i=
40.0 IN. HG MANIFOLD PRESSURE i=
1. FULL RICH MIXTURE 165 BHP ~
» 170 AND ABOVE.
;::;:
-= r--......... 2. BEST POWER MIXTURE BELOW
36 ......
a I---- 165 BHP .
(1)
--- --- r-............
150 ...... ~
"'0 3. CORRECT BHP FOR INLET AIR ~
(1) ~ t'-....... I:::::
32 .......... TEMPERATURE AS FOLLOWS:
~
a- (l) := f...--- "-.......... a. ADD 1% FOR EACH 6° F ~
JJ 1= 130 ~ i=
3
II) » BELOW Ts.
::s A ~ r= 28
m b. SUBTRACT 1% FOR EACH
2 J:
~ 110 !---
- ~ 6° F ABOVE Ts.
II.) oJJ r=~ ~
~ (J)
I::::: 1=
1=
o 24 ~ ~ NOTE: TYPICAL PERFORMANCE
m ~ 90 ~ ~
JJ 1J - (Performance is subject to f::::
"'0
!5:
o
~
"" ""- installation effects) ~
m f= 20 r=~
JJ r= 70 1=
~ = ~ 1=
~
~ ~
t=
- I---
1=
~
I:::::
50- ~ 16
~
m
?
1=
I:::::
F ~
l---- I--'
'" I:::::
I:::::
l=
m r= ~
" := 30 1=
~ ~
~ I:::::
1= --~-
~
I::::: l=-
F I:::::
~ 1=
I::::: ~
I:::::
~ 0 2 4 6 8 10 12 14 16 18 20 22 I:::::
r= 1=
~ ~
-..! I::::: 1=
<p ~ t=
o
? fill " 1111111 Tlnlllil 111111111 111111111 11111111 111111111 111111111 1111111111 111111111 11111111 1111III11 !lllllnT fTTTlfTIl 1111111111 IlIlnmT limn III 1111111111 II TlITIlIl 111111
fl ALTITUDE X 1000 FEET
-...a 11m 11111111111[111111 [11111111111111111111111 11I11111111111111lT 111111111 I mITT TTlllllllllmTTTT rmTIIIIIII[IIITI 1111111[[IIIIIIIII[il[[I[[llTlllllllllllllIrmTrmTT
tp I- I I I _
o 1=
1= __
t
f-
1= ~
~
I- 220 I 1=
I ~
1-1---1--200 1----1----- f------ NOTE: -f=~
40.0 IN. HG MANIFOLD PRESSURE 1. FULL RICH MIXTURE 165 BHP ~
t- ............... __ AND ABOVE. _I;
180 36 ............ ~ 2. BEST POWER MIXTURE BELOW ~
»
;::; ----~--~~1---_t~~~ 165BHP. ~
;:;:
r:: 1-1---+-160 t- i'--... 3. CORRECT BHP FOR INLET AIR -~
0-
(1)
t=
1= 32 " ~~ TEMPERATURE AS FOLLOWS: 1= ~
"'0
(1) CD ~ _ .... -I-- I ........... a. ADD 1% FOR EACH 6° F -t=
:D R---+-140 ........ BELOW Ts. ~
~ »
A
m 28 ~ b. SUBTRACT 1% FOR EACH ~
~::l :::r: I-
f- 120 -I-- ........... ~ 60 F ABOVE Ts. -f=:1=
(")
(1) ~ 1=
o:D 1=
I\') (f)~ 24 _ ~ NOTE: TYPICAL PERFORMANCE t=
m
~ iJ r= 100 r-=:;= I--- " (Performance is subject to -~
o
:xJ ,...--- t'\. installation effects) I;
o~
"'0
:E
m 1= 1=
I- ~ _ I'~ 1=
i: :D f- 80 __ ~ ~
1= I ~ 1=
1= ~ 1=
-s
CJ) 1= f-
1= 60 16 F=
1= ~I-- 1=
~ I=f-
~ --- - - -
.,...--- t=
f-
~ 1= ~ ~
00
1= ~
" f-
~f- g
f- 20 r::
1=
f-
1=
1= 1=
1=
f- f-f-
f-
1= 0 2 4 6 8 10 12 14 16 18 20 22 24 1=
~I- ~
I- 1=
I-
1= I-
E
P- nIT IJlIlIlI mllill 11111111 III IIJlIIIlI Illdlllllllllll 1111illllll) }l ,Jllilli 1IIIlJIIIIII1IIIIIIIIII1IIIIII 111111
ALTITU DE X 1000 FEET
1111 1111 1IIIIi 11111 11111 III: 11111 1111 ;!jIlI
f-- 220
»
:::;: f-- 200 40.0 IN. HG MANIFOLD PRESSURE NOTE:
-
:;::;: ............
C 38 1. FULL RICH MIXTURE 165 BHP
t-... _.
0- f-- 180 36 AND ABOVE.
CI) r-....
I- -......., 2. BEST POWER MIXTURE BELOW
34
"tI 165 BHP.
CI) f-- 160 32 3. CORRECT BHP FOR INLET AIR
I-- ~ TEMPERATURE AS FOLLOWS: -
30
co -.... a. ADD 1% FOR EACH 6°F
a-... JJ f-- 140
3 :> 28 BELOW Ts.
I» A f-
::l m I---- I---- 26 b. SUBTRACT 1% FOR EACH
(') I f-- 120 "- 6°F ABOVE Ts.
-
CI) oJJ
(f)
I---- f- 24
"'"
1'1) NOTE: TYPICAL PERFORMANCE
(J1 m I--- f...---
"1J f-- 100 (Performance is subject to
o o
o :;: installation effects)
m
:0 JJ f-- 80
"tI
:s::
f-- 60
~ Ef-- 40 _.-
9
Co) ~-
f---.
f-- 20 ._- j------- r--- ---- i- f--
~ .. __ . ._- t--- -
0 2 4 6 8 10 12 14 16 18 20 22 24
"m
1111 III 1111 1111 illl ilil III 11m! Innlm hmlmrtrnlrnuIlll ]I1tllr Inllim hnrt
ALTITUDE X 1000 FEET
......
~
~
c.n
"'-I
f:{J
o 11111 11111111 111111111 111111111 111111111 11111111 1111111111 111111111 111111111 III mn rnTTm 111111111 II 11111111 11I111111 II[lIllfT Hfllllll IITII
oI
r--' -
g t=
t=
t=
t=
t=
~ 220
t=
t= 40.0 IN. HG MANIFOLD PRESSURE -
t=
~ 200
t= 38 NOTE:
t= ~
t= 36 1. FULL RICH MIXTURE 165 BHP
» ~ 180
~ AND ABOVE.
::;: t= 34
t= ~ 2. BEST POWER MIXTURE BELOW
........
e:a. t= I-- 32 r-.... 165 BHP.
(D ~ 160 ......... 3 . CORRECT BHP FOR INLET AIR
." t= 30
t= TEMPERATURE AS FOLLOWS:
;:: ;--
~ CD f= 28 a. ADD 1% FOR EACH 6°F
""I :D 140
3 » t=
t:::; BELOW Ts.
1» f- 0-..
:J
A t=
m 26 "" b. SUBTRACT 1% FOR EACH
g I ~ 120 6° F ABOVE Ts.
II.) 0 t= 24
t= (
~ :D t= ~ 1=
o ~ t= NOTE: TYPICAL PERFORMANCE F
100
::xJ
."
'"0
0 1=t= ;--
'" (Performance is subject to
installation effects)
t=
1=
t=
5:: :iE F ~
t= 80
~ ~ I:::
en 1=
t= 1=
t=
9 f= 60
Co)
t:::; 1=
t:::; F
~ t= r=
t= t=
m 40
" F F
I::: t=
~ F
20 ~
1=
t=
F
E
6 8 10 12 14 16 18 20 22 24
1=
0 2 4
t=
~
t=
t:::;
"
1111 111111111 111111111 111111111 111111111 11111111 111111111 111111111 111111111 11111111 111111111 111111111 11111111I1 1111111111 1I1II1111 111111111 111111111 111111111 1111111111 11II11
ALTITUDE X 100Q FEET
IIIII i 11111111 " III "I IIITTTTTf I[[[Tlm rmmm TTTTlllTl III
, 111'"'" III""" III III III II" III " 1"""111 III" " II " " " I " II' " " II II"" I "
""""' -
~
~
t= 220 40.0 IN. HG. MANIFOLD PRESSURE
t=
t= i-"
~ 38 ~
t= 200 f'." -
t= 36 ............. NOTE:
!=
1= - 34 "- 1 . FULL RICH MIXTURE 165 BHP
» ~ 180 ~ AND ABOVE. -
;:::; t=
:. t= - 32 2. BEST POWER MIXTURE BELOW _
c !=
a. 165 BHP.
~,
I'D t= 160 - 30 3. CORRECT BHP FOR INLET AIR -
"tJ !=
1= TEMPERATURE AS FOLLOWS:
~ != 28
o.... (ll t= a. ADD 1% FOR EACH 6°F
:D 140 ~ ~.
-
3
C\)
}- != 26 '" BELOW Ts.
A ~
::s m != L---- b. SUBTRACT 1% FOR EACH
o i-- 24
(I) 1= 6°F ABOVE Ts. -
I 120 -
1= I--"'
~ o:D != ~
o CJ) t= NOTE: TYPICAL PERFORMANCE
o m 1=
:0 100 -
\J (performance is subject to
"tJ o 1=1=
s: t= installation effects)
~
m t=
:D 80
~ r=t=
1= -
9
w
~ 60
g t=
I
1=
1=
OJ t= 40
" 1=
1=1-
~
20
1=
~
0 2 4 6 8 10 12 14 16 18 20 22 24
.....
~
Ill" I" "III" ! II II! 1111 111111111 11111"1 1111111111 111111111 11111111 1111111111 11111 " I " 1111 " III 111111111 1111111111 I" 1111111 ' 111111111 II I mTTl """1111 111111111 111111111 111111
~ ALTITUDE X 1000 FEET
......
cp
o
<?
(7)
()() IIIII IIIIIIIII II1111111 111111111 1111111111 1111111111 1111111111 111111II1 111111111 111111111 IIIIII!III llLltJlll illlllill
I
UJ III !ILl IIIIIII!I 111111111 111111111 1111111111 i 11111; t11 Pl~
F
f=
t=
t=
t=
t::
t-
40.0 In. Hg MANIFOLD PRESSURE
i
~
220 38 ........ NOTE: -1=C:
I
»
::;: I 1. FULL RICH MIXTURE 165 BHP t=
36 ,..
f--- I AND ABOVE. r
...s::: - ~ I'.
Q, 200
(I)
t=
I=:
- 34 -~ ! 2. BEST POWER MIXTURE BELOW T
"C F 165 BHP. T
(I) I
~ 180 32 ~
~ "- 3. CORRECT BHP FOR INLET AIR T
1= TEMPERATURE AS FOLLOWS:
3 1=
i= 30 +:
!),)
:J
co a. ADD 1% FOR EACH 6°F
JJ 160
--
o
(I) ):>
A
28
".'" BELOW Ts. l,
+=
N m b. SUBTRACT 1% FOR EACH t
()() r-- 26 t·
o I 140 6° F ABOVE Ts. _l-
o ~ [.
:lJ
oJJ ~ 24
"C (f) t= NOTE: TYPICAL PERFORMANCE
mF ~ I-- +-
s:: -0 120 ~ (Performance is subject +
o I=:t= to installation effects) f
~ ::! t=
m~
JJ 100
F
I=:
F ~~
t
~, t= 80
t=
t=
"m 1-.
t= tr-
t= ,.t-
~ L
Ft- .;:..::
t=
1= t.
~ ~.
Ft- G
F
t= -
~ 0 2 4 6 8 10 12 14 16 18 20 22 24
1=:1- t=
F
1= t=:::
r:::
1= t=
I=:L
...L ..l.
11111 UillWII I1I1 111111II1 I11I
ALTITUDE X 1000 FEET
I
11111 11 II UIIIIII
-=
==
NOTE: 1) Horsepower Correction: ==
-=
a) Add 1% for each 6° F below U.S.
::::
=
Standard atmospheric temperature. ~
b) Subtract 1% for each 6° F above U.S. ~
Standard atmospheric temperature. -+---t-----1r-------,.f----t---t22o ==
2) The above correction is for induction ==
::::
air temperature at the compressor inlet.
/ =
3) For Fuel Flow Management see Page ~---+_--_4~--~---+_---+210 ~
"0<f~ ~~
R----+NOTE: TYPICAL PERFORMANCE (Performance
subject to installation effects.)
IS - f - - -
~~
p.~ V /
.-v......~7---+-,.<---,.I'----+----+200
_~
I
Fr-4r----r_-4r----r_---+----+----+----+--~J+_~19<:::5 ~
/ ~:;~ V<
/
190
180
I~
=
=
~__..,fC--++_----+_--__j.170 ==
~
I--I-o---i---MAXIMUM CRUISE
.
/j /
/ ///~~\):;~ V/
'" ~ ./ . 160
~~ ffi~
~
~I-r-MAXIMUM
I I I
RECOMMENDED CRUISE;
I I IVA /~V
/1A11.iY-:::))t}/ ) / 150
~~
~ gs
~ / / .I1'nW{~0Y /~~. ~~
~
1=-==
~1rj.wy</:;{~:::':'
;::::j'
r::P<f?
<'k<:: 5
.':' :-. .
I 140 ~ ~
f::: CD
1= .-:-:': :.::::1' RECOMMENDED CRUISE- 130 ~
~ / / (}/V/ / I I I I I E~
~ // .YYV,
F-:t---4r--r_---t-----1f-+-+-'7ftttf'1rtH~T_-if---T-!o--+_-ECONOMY CRU ISE t " 120 I-I-f-
I ~~ ~V I ~
I ~ /
~---+-----+----+_~T1~~+H~~~--~--~----+_-_4I----~-~+-----+---~110 ~
1m] PREFiRED iRUISING RANGE ~
~
l=
[illill:. RECO~MEN~ED 100 ~
F
F~~__~-~---H+~~~~~---t---__r_--_t_-__+~C~R~U~IS~IN~G~R~A~N~G~E~S~-+_---+90 ~
F=
f:::
t=::
I I
MAXIMUM CRUISE
I t=::
f::: II F
~ w~
1=-==
f:::r
E
t=::
~ ~
1= 1=
~f- 22 24 26 28 30 32 34 36 38 40 ~
~ ~
1IIIIllIIllllIJ i 111111111 Illlillli 111111111 .1111l111I i 111111111 111111111,111111111. 1111I1111 111111I1 111111111111111111111111111 IlIll
MANIFOLD PRESSURE -In. Hg ..
76-00-69
1111 1111111 1111111 1111111111 111111111 1111111111 111111111 111111111 111111111 II 1m
-1
!= t==
!= l=
::::: t::::
F
!=
!=
1=
~ 0 F
C\J
!= 1=
I=:::
F
~
!=
\ !===
1=
E:
F
!=
!=
~
\ co
..-
1=
E
~
1= !=
1=
!=
~
:::
\ 1=
E
~
E:F
:::::
:::::
::::: \ CD
..-
E
t::::
:::: u.i E
:::::
:::::
::::
::::
::::
o~
zw
«0:
0:
:::>
\\ E
F
E:
1=
1=
:: WCL F
:::: >w 1\ ~
..-
~ (J)
CL
;= ...Je)
\
!===
E «0: F w
f= >« E 0:
t= oI
...J()
F ::J
= 000
(J)
I=:::
r\
(J)
F u..- W
-0
~ Zo C\J
..-
0:
CL
1= «eo
!=
I=:::
~
~o:
1-:::>
«l-
\ f\. i-
...J
W
::J
u..
f::: o
\
I=::: ZO
1=
1=
WI- 1= UJ
E 0:
:x:: 0
~ «w
1-1- -- 0
..-
F UJ
I-
00 E
~
I=::: Wz CL F
UJ
I=::: ~
1= eow Ii) E
~ 1->
OOw - C\J
. F
+1 '\
1= :::>eo w
!=
'"
~'I-
F
1= wOO +--Z
()
0::::> co
«
1=
1= :::>~ 0: "- F
~
!=== OOw w F
...J
~ (J)e)
w« +--...J 1=
F
F
1=
I=:::
~
g:e) 0
I- '" ~ !=
E
~
ill CD
F I- F
!=
!=
~
0
Z ~ 1=
!=
l=
!= ;
E
I=::: F
F 1=
~ ~
1=
!= 1=
F 0 0 0 0 0 0 0 E
I=::: CD
..- ~
.-
C\J
..- ,....
0 co CD ~ !===
~ 1=
I=::: F
~ I 1"-
1=
II1I1 IIIIIIIIU 1111111111 1111111111 1111111111 !111111111 , I rIll
FUEL FLOW - Lbs'/Hr.
Metered Fuel Pressure VS. Fuel Flow All Models Except TS10-360-LB & MB
76-00-70
Wil WIIIIIII IIII1 11111111 1111111111 I II I ~ II I I 11111111 II 11111111 111111
F F
~ r=
1=
t= BASED ON SET UP AND FLIGHT TEST PROCEDURES SAME AS PIPER PPS. 5:
F * DENSITY ALTITUDE TO BE MEASURED AT THE TURBOCHARGER COMPRESSOR INLET.
t=
f=r==r- WHEN ENCOUNTERED CONDITIONS OF EXCESS VAPOR INGESTION BOOST PUMP
r==
-1=
1= t:=
~ OPERATION MAY BE REQUIRED TO STAY RICHER THAN LEAN LIMIT SHOWN. 1=
I- 1=
~r- NOTE: TYPICAL PERFORMANCE (Performance subject to installation effects.) -1=
t=
F
1=
1=
I I t==
E
E
:::::
C\J 1=
"<:t
...- E
I ~
1=
I co 1=
t=
1=
I II STATIC SET UP RECOMMENDATIONS
(")
...-
t:::
F ==
E
t=
F
I
I
"<:t
(")
F=
t=
~
"7
/ ...-
~
1= t==
t=
F
/' 0
(")
...-
=
=
~ J ==
7
1= t==
t=
F
CD
C\J
1= Cf)
1= a::
r= ~
T""
::J
~ V 1= o
t=1- C\J F= I
t:::
F= ,...
C\J a::
F= / w
== 0...
=
F=
1=
E=
E
E V
/' , co
.,....
...-
t== o
=
t== Z
= ::J
o
Cf)
1=1- ,...
"<:t t==
;= 0...
E / ...-
f=-
~
F f= o
1=
1=
r=
E
E
V
/ I-
0
..-
,...
CD
r= -l
F=
~
f=
r=
U.
-l
W
0
...- t::: ::J
u.
~ / :::;::
::J ~
1= 1=
F
1=
~
1=
1=
1/
/ z
«w
-l
* DENSITY ALTITUDE
C\J
0
...-
co
F=
t::;:
r==
t=
F=
1= t=
~
F
/ THOUSANDS OF FEET
J I I
OJ
F
t=
/
C\J 0 co <0 "<:t C\J
t=
t=1- . ...- 'Ot F=
~ T OJ 1=
F
~ 0 C\J 'Ot <0 co 0 1=
F
t=t"-
F
(") (") (") (") (") 'Ot 0
OJ 1=
1= I I I I I I ~
~ MANIFOLD PRESSURE 1=
E
t=+-
t= ("HG ABS @ WIDE OPEN THROTTLE) !=
1= t=
J---
F
F~
1=
t=
II1II 1111111111 1111111111 1111111111 1IIIII11II II rn 11111 1111111111 1111111111 1111111111 IlmmTI mmrfll 111111111 1111111111 111111111 111111
Typical Engine Fuel System Operating Characteristics 2600 RPM (Standard at S/L)
All Models Except TSIO-360-LB & MB
76-00-71
500
AVGA'S 750
450
=
400
350
._-
300 ~
ci
--
I
vi
L
:/
aJ V
..J
s:
250 V
0
..J
U. /'
V
..J
W V MAXIMUM PRESSURE DROP ALLOWABLE
:)
u.
200 / ACROSS A SUITABLE FLOW TRANSDUCE R.
/
150 /
V
/
100 /
I
50
/
/
o
o .5 1.5 2.5 35 4.5 5.5 6.5
PRESSU RE P. S. I. G.
76-00-72
I I I I I I I
- I
I"'"
I-
- 450 -I-
-fo
~
/' 400
-I-
- V CHT
- *' 350
300
I-
1500
/ '~ I-
1450 I'"
/' ~
l-
~
I-
1--
1400 / '- ........
"
I-
TIT I-
~ 1350 i"oo..
........
l-
I-
1300
I-
I-
BHP
'i:' ~ ~ 0::
~c..
:::I: .55 ./ -'" 100
(.)0: V r" I-
>-fo
/ ~V
-:::I: w
1.1.03 en
011
w...I - .50 90 0::
o::t:
c.. ...... / V
ens:::
w 0 ( V W
~
-
~; ...". 80
~~
.45
............... ~
I"""" ~
IX!::::J
II) I-
s::: BFSC -- IX!
o I- .40
(.)
I-
I I I I I
-
40 45 50 55
FUEL FLOW (LBS/HR)
l- ~
l-
I-
50 - of'
<'-'
I-
/
~ ~
~
wW
::.t:0:::
0::::)
-
AOO - w ....
,... CHT o~
Zw
:::;Q.
350 - >-:s
uw ....
1650
1600 ~
/
-
1550
1500
'"'" I-
I-
1450
1400
TIT
'" " I-
1350
l- I-
'C'
~
-
,... .55 140 I-
"",.... r-
UQ.
_::.t:
LLIrl
(3Ui
w.c
-
.50
/
~
/ BHP
/ 130
or-
r-
Q.c
(f)c:
WO V
--
~; ./ 120
.45
~~ ", BFSC
Irl :::I
III
c: - ~ -
o .40
U
- I I I I I I I I
:
50 55 60 65 70 75 80
FUEL FLOW (LBS/HR)
--
,v --- of'
~50 -
c:("-'
r Ww
r ............... ....... ::t:0:::
0::::::)
00 - wI-
r CHT o~
Zw
:::::ic.
350 - >-::lii
ow
I-
- 1650 -
1600
/
/ ~ -
r
1550
1500
I
'" ~
"-
"-
'"
r
r
-
1450
1400
TIT
" ~ -
r
r-
BHP
f- "....
.55 ./ / 160
.50
/ "" '"
V 150
V V --
.45
I V 140 -
I ;/ -
......... ~ BFSC -
.40
_l-
I
I _1 I I II I
60 70 80 90
FUEL FLOW (LBS/HR)
~t>-~
~v'Y
. V
./' ", ,.. ,'" 80
:::>
u..
~O t>-~'" O~S~ 60
'r~~,?-oi--'!'''' <::0<V~/"""
~~~,.
~,.
T S~
<v~
50
0~
~
E
40
l..oI
"'"
NOTE 2
I .
......
III
76-00-76
11111 'IInrrm mmrr IIIIfIHI I mmm 1111 III 111111
I I I I
1= '"" 111"""1 '"1111"1 1111111111 1111111111 1111111111
1=
1=
1=
1= -
NOTE:
1. Data is approximate with fuel
pressure gage at same elevation
as manifold valve and without -
influence of differential fuel head
:: in gage line.
a
(!)
2. Nominal tolerance: :!: .30 psi
[
s:: 3. AVGAS @ 78°F
"c!2. ~
g} 18
"'0 m
@ o
til
til C 16 /
C
... "
m
(!) r
"'0
~ 14
VV
~ (f)
(f) V
"c C
!2. ~ 12 ./
" "0
!E. V
~ ./
10)
Ci! V
9 ...,.
V
8~
V
~
r ,.../
m 6 --'
" =l
l--- ~
44
2~
---
~ £'
o mrIT nil II 1111111111 111111 111111 III II 11111 II IIITIIII fIInTlIll IllffiHlT 111111111 1111111111 "" 111111 111111111 1111111111 1111111111 11111
..., o 20 40 60 80 100 120 140 160
~
<:I FUEL FLOW - Lbs/Hr.
T'
...,
"
NOTE:
1) Ejector PIN 642955
4) AVGAS@84oF
E
60 1=
1= I
F
F
F
I
/ /
V
I-
1= /
1=
1=
50 I-
1=
1=
/ ./
V
1=
f=
1=
I-
1=
/ /
/ V
<.!)
1=
(J)
0... 1=
1=
I-
I 40
w
0:::
::::>
(J)
1=
1=
F
1=
I--
i7 V
~~ /
~#7
(J) I-
W
0:::
0...
c... 30 / ~~;..; ::::
~
::::>
0...
t:::
1=
1= V V
l= / ""
I
V
1=
1= V
20
1=
t:::
I-
1=
V /
1=
t:::
1=
I-
1=
1= l:-
10
E
l-
II
40 50 60 70 80 90 100
VAPOR RETURN FUEL FLOW - LBS/HR
76-00-78
I::::
~ IFUEL IINJEC~ION pLMP I~LET plRESSJRE R~QUIREIMENT~
==
==
:::::
::::
=
==
::::: -
~
==
==
:=
==
:::::
==
==
==
=
==
=
=
==
==
==
==
==
60 ==
==
== MANUAL MIXTURE CONTROL REQUIRED
==
==
50
=
==
=
/
V
==
::::: ~~~ V
==
== ~~p
:!:! 40
==
==
==
==
~~/ ,
~\-(.y..
~
9V~9
V
V
== ~~O -(.\0
O~C:J'\ ,,\~~~(j
U)
Q.
W
=
==
=
;=
V./
ex:
;:)
t:= <CV~ V
U)
U)
g:w 30 t:=~
:::::
:::::
./
V /
/
:::::
t:=
:= r-- V V BOOST ALLOWED FOR VAPOR SUPPRESSION
AND PRIMING AID I I I
:::::
:= r-- V MANUAL MIXTURE CONTROL MAY BE
t:= DESIRABLE
20 :::::
:::::
==
==
==
==
==
10
==
==
MINIMUM ALLOWABLE
=
==
== I
111'1 Lilli
IDLE 20 40 60 80 100
PERCENTAGE RATED POWER ENGINE RPM
76-00-79
E
1=
E
E
E
1=
NOTE:
1. Sea level horsepower correction
a. Add 1% for each 6°'F below 60° F
b. Subtract 1% for each 6° F above 60° F
76-00-80
3.4
Q = ACTUAL INLET AIR FLOW 1
N = ACTUAL TURBOCHARGER SPEED
fie = COMPRESSOR EFFICIENCY
120Kl r--.....
3.2
T1 = INLET AIR TEMPERATURE -·R
6= CORRECTION FACTOR - T1/520
/ ""'" "- ~~
/
/
3.0 \
2.S
110K/ r--
II
t'--..
I -- ~
"\
V-
2.6 / / 1\ \
, 100KjJ r--
t--.... J
II jU
0
~
c?
i=
2.4
/
L
'" ~.
1~ 1 II
<1:
a:
UJ 2.2
90K
I
- If- ~. ~L
a:
:::>
U)
U)
~
t:J::
V t'-...I J Y
UJ
a:
0-
a:
2.0 ~
....c J 1J
0
U) 8 SOK
I / V\/ j
U)
UJ
a:
0-
2 1.S it'"
If
II
/
--
r\ Ii" / i !J
0
0
} V j\ VI \
-
C,)
i+-70K /
/
1.6
$ VI ~ -L I I rY'
60~ ~V/ \
.70
2 / / / .65 I
K
1.4 V /' 7 "J k:
.60 .55
/ .50= Y/.c
I /' ~~
/ V
50K J / -/
1.2
f-4/
/
. /? tX t:/
V
~
K I' "
1.0
,/
100 200 300 400 500 600 700 SOO
AIR FLOW Q/-re:- -CFM
76-00-81
RPM CORRECTION REQUI REMENT FOR O.AT. VARIATIONS.
I I I I I I I
(PRELIMINARY CRITICAL ALTITUDE CHECK
STATIC BUN UP AT W.O.T. DETERMINING ENGINE
SPEED REQUIRED'TO OBTAIN 40" HG. MAP)
I:::
2500
h
2400 ~~ f::
~~
E
2300 ~~
::0
--0
s:
~~
2200 0V
0V
2100 0V
~V
2000
~/
0 20 40 60 80 100
OATI(OF.l
. -
76-00-82
t-
l I I I T I I -,
11111 1111111111 1111111111 1111111111 1111111111 111111111 1111111111 1111111111 1111111111 1111111111 1111111111 1111111111 1111111111 1111111111 111111
t= E:::
t:=: t=
t= ~
t= ~
t=
t=
t::::: CHARTS IN~TRUCTIQN~: ~
I::"t-
t= ~
~ 1. Obtain actual maximum rated RPM. l::::
~ 2. Determine required RPM for 75% power by reading directly above the actual maximum rated 2:
F
r:-
Ft- RPM point.
F ~
F
::: 3. Determine fuel flow limits for the 100% and 75% power by reading directly above the actual t=
t=
I:--
maxiTum rat~d RPM pOint. I
I I I I I r=Fr:-
t= t==
1==
F
t=
EXAMPLE:
I I I I I I I t=
t=
~
I:-- 100% Power, RPM 2700 ± 10 Flow Umits, 135 - 145 Lbs./Hr.
t=
t= 75% Power, RPM 2450 ± 10 Flow Umits, 71 - 93 Lbs./Hr. ::::
c:
t= (34.0-36.0 in. Hg. ADMP R~f.) c:
~ I I I 1 I I 1
==
~
I I I I I I I J c:
c:
=
=
F
NOTE: This chart is for 70°F fuel temperature measured at the engine fuel pump
inlet. For every 10°F increase in fuel temperature subtract 1 lb. of fuel
F
~
'=
=
=
=
from curve. For every 10°F decrease in fuel temperature add 1 lb. of fuel
to the curve.
=
F
~
== ;::
=1-
==
=
-r=r=~
=
f= High Limit
- 100 f!?
~
c:
~
t=1-
1==
t=
f=
- 90
::J
::0
...J
""":'
a::
l:
-=c:c:
~
t=:=1-
t= IJ.. ~
-F
r=~
t= w
...J en
t=:=
f:: LOW umit -
80 ;:)
IJ..
-
£D
...J F
~
-
f:: '#. c:
f= It)
I"-
F
r-
70
f=
f:: ~
t::= -~
:= 2450 2475 2500 s=
t=
t=
t= ENGINE RPM F6R 75% POWE~ 1=
-1=
1=
f= I ~
t=
~~ l---
1= 1=
1=
1= - ....en
t=
I:--
1= - ~ 145 :E
::J
1==
E
~
t=t-
t=
1==
t=
t== LOW~ l---
140
::0
...J
IJ..
...J
-
Ii
l:
~
-~
1=
1=
1=
t= w en -/==
l..--- ~ E
1=
t=:=
f::
f::
135
;:)
IJ..
'#.
0
,..
0
-
£D
...J E
j:::
1=
1=
1= 2700 2725 .J50I
1=
E== 1=
t:::::1- ENGINE RPM FOR 100% POWER F
f:: 1==
F= E
f--
f:: 1=
1=,- I I I I
l=
JIIII 1111111111 111111111 111111111 111111111 1111111111 1IIIlITm mllllill 1111111111 1111111111 1111111111 1111111111 1111111111 11111 III llULl
76-00-83
I
111111 n 111111
I ]
~
I
~
- ::::
F
i=
40
I r=
(9
I
V 9
0'" I
I
i
I
t=
t=
F
t=
Z
(fj
if)
~ 36
38
,
I WV
~
VV
",0«'-
VI I ,I I
I
I
I i ,
,
I ~
t::::
== 210
:=
a..
Z
!===
~ 34 ~
E
E
I
I
/l V!1 f ADMP
I
i! I
I
[
i
~
~ 200
~ 1/ / II
I t=
>- ! I t=
a: vO i E
o
(fj 32
[
0« I I ~ 190
~
'V1 /1/
I
Cll I
1
I
« I
I
I I I <v I I
I
I
I ~
t::::
30 ---!-- 180
~9 !/ !
I, I I, I I ==
--E-
'V!
i
B IV
v~"'"
I I
-t- { --+-- I 170
i I I i --.'
~'7
I I
I i I
I , ,I
!
i ~
= 160
a:
UJ
I I ~
V o
~
/
I
BHP i
I i ;
i
.0..
/ i
--t
! i
I
I
:
II
~
150 ~
UJ
if)
/ ~
O~
I
I
J I ~ UJ
&'
I I 140 ~
t=
i V I Q.«' . I
i
I
I
!
I
I
I
i
I
,
-t=
t::
~
130
a:
Cll
V11
I I I
i
I
..: t
I i i
I i I §
I-... ! I
I
i
i I ! i ; ,
~ .80 --i-- I
120
Cll
-... I
II , I I i I,
! ~
I
I
i ,
ui
..0
-I .70
!
!
: FULL THROTTLE
i i ! I 1- i
;=
~=
110
!/ [/ -=:::§
I
Ii Ii!
I
if)
z ! I
o I BSFC! J
I I i
()
-I .6D
i i I
!, I
,
100
,
~
!I i
UJ It PROP LOAD
II
::J
lJ..
ci .50
II
I / I I
II
I --'---
I
I i
I
i
I
!
!
-~
~ 90
UJ
a..
I
I !
V I
!; I
I
i
I i
I
I
I
I
I I
if)
I i I
i I I I I
i
I
I
I
:=
1= I
~
i= i
IIIIIIIII!IIIIIIII)IIIIII 11111 I! I 'hmhmhmtn,11111 i 111111:; ,,- iilliurriTTfTml1trrniTTTfifllll ITT Tmmn I ililil
2000 Z200 2400 2600 2800
ENGINE RPM X 100
76-00-84
TIT TIT TI11 rm mr TIT TTITTTl mmr TIT rm TIT TTTTTT mmrrrr TIT TIT TIT rm TIll mr
i =~==~~
~-- ..+ .. 220
NOTE: I
1. FULL RICH MIXTURE 75% POWER AND ABOVE.
f--- 1-200 -
2. BEST POWER MIXTURE BELOW 75% POWER.
3. CORRECT BHP FOR INLET AIR TEMPERATURE AS
»
;::;: I - - H80 FOLLOWS:
-
;:;: a. ADD 1% FOR EACH 6 0 F. BELOW Ts.
c b. SUBTRACT 1% FOR EACH 6 0 F. ABOVE Ts.
c.
(\)
"tl
Ff---- 1-160
(\) E
:!. EI-- g> H40
o.., '"A
3
$I) ~ ~~~ 1-120- ~N. HG. MANIFOLD PRESSURE
:::s
(')
(\) § ~
..... :f- !!l:< f-100
~r-..
CIO
o ~ :::::.~
o i'--..
I
:D 80
"tl I--
:s:: ~ ~ t-- ~ t
60
~ ~ !--- f---- ~
;; ~ f..---
9 40 --
w I
(I) ~ f.-- I
E ~ t-- I
crr- 20
'" I
aJ
::
I n
0 2 4 6 8 10 12 14 16 18 20 2,2
~ 2j
I j J..- Alt!tude
I Xi i i . !
.~~ 1000 Ftet-~~t Ii
1 I
I
Illi,",i""i""I""i""I""I,"!il"i""i""i""i.'''I''!
"-I
<p
o
oI
CIO
0'1
TTTTl"11TTTTTTI mmm lTTTITTITmmmT mmmrnTTTTTTTlTTTTTTTTT 1iTTiTTTrmmm
~ I ! ! I'
o § j
~ 220 , f-J
0) ~ i i
I
NOTE:
I i I I --JI
I i j 1. FULL RICH MIXTURE 75% POWER AND ABOVE.
200 -
2. BEST POWER MIXTURE BELOW 75% POWER.
I 3. CORRECT BHP FOR INLET AIR TEMPERATURE AS
FOLLOWS:
I i Ii
180 .-
i a. ADD 1% FOR EACH 6 0 F. BELOW Ts.
I I b. SUBTRACT 1% FOR EACH 60 F. ABOVE Ts.
I I I
160
~
~ r-.....
I-g:' ~140
ru -.........
Ir
a A
(1) ro 32 IN. HG. MANIFOLD PRESSURE
I r- ~..............I
"tJ
30' I-Q(I)
f-120 I
o ro
... "0 ~
~::s
(')
E-
t-
~
ro
.... -
1-100
-- - ~r- - ~
~
I
(1) ~
f: ~~ "-~ I
! I
g ~ 80
o - "-
::0 ~
"tJ !--
s:: 20 ~
60 ""'r-....
f..---" ~
~
I
9
Co) 40 ~
16 -
-
~ 20
1
I
I I I
0 2 4 6 8 110 12 1'4 16 20 22 24
1,
! I i I
AltItude X\1000 Fret !
1
I i
11111 111111111 WllllllIIIIIIIII 11111111 11111111 1111111111 1111111111 1111111 1111111 IIIIlJillUll
-T 11111111 111111111 1I1111L1 III1IWU!1111I11 IlllUilll lllllllill 1111111111 IHill
t=1
~
t= ~
F
t=:::
t=
f::
220 t=
t=
t=
t=
f::
200 ~
NOTE: ~
1. FULL RICH MIXTURE 165 BHP ~
»
;:;: 180 .. AND ABOVE. -1===
;:;: f-
C 2. BEST POWER MIXTURE BELOW ~
0- 165 BHP. ~
('I) r----.
160 t--- 36.0 IN. HG MANIFOLD PRESSURE
." 3 CORRECT BHP FOR INLET AIR -t;
('I)
::l.
I I . TEMPERATURE AS FOLLOWS: 1=
r-
o... OJ ~ a. ADD 1% FOR EACH 6° F _~
:D 140 32 -
3
s:u
::J
(')
»
A
---
~
f-- ~ BELOW Ts.
b. SUBTRACT 1% FOR EACH
~
r-
~
('I)
m
I 120 28 ~ 6° F ABOVE Ts. -~
~ o - t=
o :D t- j.---- e-- ~
o en NOTE: TYPICAL PERFORMANCE
f::
~
:::0
m -~. ---_.
~
"'0 100 24 ....- (Performance is su b'Ject to -f::
i=::
." o
s: ~ i=::
I--- I--- instaflation effects) ~
m ~ ~
~ :D 80
f=
20 - f=
9
Co) r ~ - ~ f::
en ~ f=
60 F=
<? l-
t=
Iii 16 t-" - F=
f::
I - - I--- '., .. _-_.. ,- -~ .. '- ~
40
f=:
--- ---
r f::
f=:
20
t=
f::
t=
F=
~
0 2 4 6 8 10 12 14 16 18 20 22 24 I-::::
F=
F
F
t=:::
~ E
i -.l --1
JlJJ 11111111 IJJ llllll 111111111 IIlIillil 111111111 Willil 111111111 lU1illil 11111111 W1lill 111111111 1111111111 IIlrl
~ AL TITUDEX 1000 FEET
.....
cp
o
c;> r
! I
~ ! I
220 r
I
! NOTE: I I
I 1. FULL RICH MIXTURE 75% POWE R AND ABOVE.
200 I i -
2. BEST POWER MIXTURE BELOW 75% POWER.
40 IN. HG. MANIFO~D PRESSURE 3. CORRECT BHP FOR INLET AIR TEMPERATURE AS
180
-...... ! FOLLOWS: -
a. ADD 1% FOR EACH 6 0 F. BELOW Ts.
36 b. SUBTRACT 1% FOR EACH 6 0 F. ABOVE Ts .
l> 160
------ ~ ...... ~
......
! . I
;:;:
::;: 32
~
a I
CD t-~- t-140
III
"'D A
" f'..... ::s
CD
2;
co
I
---- 28
I-Q- t-120
~
~ '"co
"0
"'-
:::I 0 '''-
g :i! f---
' .... ~, .. " ...
I-~- t-l00
I--- -~ "
~ ~
o
::XI 20 ~
80
"'D
::: I---- I----
-
(rio
60 ""
9 ~
~ ..-
w I----
~ 40
r- "
aJ
20
I
I
0 2 4 6 8 10 12 14 20 22 24
I I i 1t
AI TUde X 11000 Fr t
Y
TI
mTT mrr I
I
~
220
0 2 4 6 8 10 12 14 16 18 20 22 24
, I
I I I
Altitude X 11000 Fret
.....
iE
tf>
o . I ,'F 1 ,I· ..
oI
00
CD
~
cp
o
cr
<0
o
E~ 1-200
~ 38 "-, I I I i I
36 ~ I ,
I i ll
» ~f--- 1--180
;:; 34 I K T !
;::;: 1 i
'",-
C I !
Q. ~f--- 1--160 - 32 i
I
(1) ""'-
30
"'0 ~ ~ I
(1)
'" 1-140
~~~
0
-
28
"" ~
t
U!
(I)
26 I
_u ~120
I
0
I»
f
:l
(') ~ ~
24 j
I
(1) -100
I\)
~-
~
"
~ ::
I! i
o 80
::D NOlI: I
"'0 ~ 1. FUll RICH MIXTURE 75% POWE R AND ABOVE.
s: 60 2. BEST POWER MIXTURE BEleM' 75% POWER. -
3. CORRECT BHP FOR INLET AIR TEMPERATURE AS
cri ~ FOllOWS:
40 -
a. ADD 1% FOR EACH 6 0 F. BELOW Ts.
9
w ~ 0
b. SUBTRACT,l% FOR EACH 6 F. ABOVE Ts.
~
20 ---~-.
, I
~ ,
I
,
Ii; I I I
I
~~
! I I i i i I
0 2 4 6 8 10 12 14 16 18 20 22 24
i ; ! i I I i
~
Alti1tude X ,1000 Frt I I
~ i t-l
i I I I
Ull III 111111 1111 1111111 lIlI 1111111 1111 III 11111 lIlI IIlIIII III
I II ! !
- f-220
I. I I -'- I
40 IN. HG. MANIFOLD PRESSURE
~!t----~i I 1--+
i
38 1~ i I II I I
f-200
- I
36 i I
» .- ~h,
I
I
;::;: 34 """"-i I
;::;: ~!-- f-180
i
C I
0. 32 ~
I ;
(I)
! - - f-160 30
"tI I
OJ
(I) Ql !
- 28
a- -'"'"I f-140
""I 0 26
3 ;;l
ro
I I
"" :
I» 24 I
::J -"8 f-120 I
o(I) ~ i
----
I
I\) I I
- f-100
....
o
o
--- I 1
!
:x:l 80
"tI NOTE: I
s:: 60 I 1. FULL RICH MIXTURE 75% POWER AND ABOVE.
-
2. BEST POWER MIXTURE BELOW 75% POWER.
Ci1 i CORRECT BHP FOR INLET AIR TEMPERATURE AS
1 3.
9 40 FOLLOWS: -
Co) I a. ADD 1% FOR EACH 6 0 F. BELOW Ts.
b. SUB!RACT, 1% FOR EACH 6 0 F. ABOVE Ts.
~ I I
20
(Xi I
I ii
I I
j
I I I I I i I
0 2 4 6 10 12 14 16 18 20 22 24
I I
~ !
II
J
I I
,-----~
Altitude X 1000 Feet I II
I
I I I I I I I I I
....
cp
o .:;-,..
o
cO
.....
r-
130
'" ~ "-
.
0
....0
x
" '""- u:-
0
0
II)
"'"
:E (I)
c.
.
0:: ~
!:
l-
~
0
w I/)
w :;:)
c.
I/) 120 0
I- :;:)
~
w z
z i=
iii z
0:: 0
:;:) u
I-
~
:E
I- I'" ~
:E
I-
"'" '""
"-
110
"~ L
1700
...
j .. "
f: 0
N
j
~
N
~
g.
tg 0 ~
g 0
N
l'
§ ~
Ef
~ u. ==
0
;2- UJ
~
a:
::l
...<t
~ a:
~
UJ
'"
:;:
~ 0
...
UJ
~-
I
oJ
(5 ~
E
~
~ 0
j
E :::
~
§ ::::
~
F 0
==
::::
c: ~
~
-
~
~-
~
0 c.;
.... :: ..
M '"
M
76-00-93
I I
. I
l-
I-
-
-
FUEL FLOW VS. PRESSURE DROP
300~--~---+----+---~--~~--~--~----+----r----~--~---+---+;
I-
//
250~1-~~----r---~--~----r----~-~--~~---7~--~--~----~--~--_~1-
~ I- /"
~...J 200~--~--~-----+---~V-----~--~--~-----+----+----~--~--~--~
... 1-_ MAXIMUM PRESSURE DROP ALLOWABLE
3: ACROSS A SUITABLE FLOW TRANSDUCER
;W...J / --
150~1-~~------+-----*~---~---~---~-----~----+------+----~--~~---~---~
~ I- ~ I-
100~:~~~~~+-----+-----~---~---~-----~----+------+----~---~~---~--~
-
I
50 =I/
~-~+M~~~Tr~+r~~~Tr~+rrll~~~~n+Trl~+r~TMnI~rlM~Mrl -
OL-~~~UI~wu~~~~I~~~~~~~I~~~~~~~~~~~~~~~
o .5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
PRESSURE PSIG
50
I- 1/ V
/
/ / l-
(!)
en
c.. 40 V / "
~V V
I
W
0::
:::>
en ~
-
en
w
0:: V V
c..
30 / /
/
/'
/ ""
20 1/"" / ./
10
I
II
40 50 ~ ro ~ 00 100 110
VAPOR RETURN FUEL FLOW - LBS/HR
~
-
r-
f=
f=
t:::
==
:=
F
t=
~
t=
t=
t=
60 ~ f=
t=
t=
~
t=
t= MANUAL MIXTURE CONTROL REQUIRED f=
~ ~
t= f=
F
F V F
f=
~
50 ~ /
F ~\~~ / ' I=:::
t:::
~ ~~p t=
~~/
r=
f=
f=
I=::: ~,«,.y.. fl~~fl V a:
w
:! 40 ~ ~ ~ ~ ~
o0.
t/) r;.~Q ,,<,0 /
0. ==
t= rf:,~'I. ~~v t=
W
a:
I=:::
~ Q rf:,\-'~ V W
t/)
a:
:::l t= v ~V /" o
t/)
t/)
w
g: 30 r=t:::
t=
t=
L
V V
l':
w
~
ct
:=
:=
;= I-- V /
/ BOOST ALLOWED FOR VAPOR ISUPPjESSION
AND PRIMING AID I t=
a:
E II)
f= V MANUAL MIXTURE CONTROL MAY BE
F I--
E DESIRABLE
20 ~
I=:::
E
~
==
t::::
F
F
t= MINIMUM ALLOWABLE
10 :=
==
III' Il
IDLE 20 40 60 80 100
PERCENTAGE RATED POWER ENGINE RPM
76-00-96
OISd 3~nSS3~d 13n:l
co ....co o
".. ....
N
.... co N o
o
-
I
.
IN. I
. I
I""
....co
\.
\ 0
....
~
'\, III
en•
oa
- III
\ -
0
N
.....
:lE
0•
\ -
-
CD
M
Q
•
\\ -
0
0::: en
::;)
0 3:
....0 ::r: 0
I-
0::: ..J
\ - W
c.. LL
I- ..J
\\
(J)
- - C
z
W
;::)
I- 0 ::;) LL
co
- 0
c.. en
I- ~
>
w
3: t.'t:
-
-
\ 0
..oJ
LL.
co ..oJ
0
w en
;::)
en
\ ::;)
LL.
W
t.'t:
a..
~
..J
- W
;::)
0
~ LL
-
-
\ -
C
w
t.'t:
w
\ 0
N
I-
W
:lE
I I I
I J I I I o
co
.... ....
co
....
N o
.... co N o
T510-360-5B
Metered Fuel Pressure V5. Fuel Flow T510-360-MB, 5B
-- en t:::
145~ !: ~
·ntit :E !=
~:::-- I :::; !=
!=
~ ==~
135- oil: ~
!=
...l~.
u.. !=
I !=
--~---
en
130- ...lID
W...l
f= ::J .......
f= u..
f= I if. f=
125- 0
I ,...
0 f=
I- 2700 2725 2750 f=
f=
1 J ~
ENGINE RPM FOR 100% PO~ER !=
1:::
IIIII 1111111111 IIIIIIIII IIIIIIII11 1IIII1III11IIII1I
76-00-98
220 NOTE: -+--+---+--+--+--+-1220
1) SEA LEVEL STANDARD ATMOSPHERE AT
COMPRESSOR INLET AND TURBINE EXIT
210 WITH ZEROIRAM. -t--I::I210
2) INDUCTION AIR TEMPERATURE AT
THROTTLE BODY 1150 F
200 -+--H200
190 H-~--+---r-~--+---r-~--+~~~~-----r-~190
180 -t--I::I180
170 R-~---+-~--4---+---r-.A~~~~-4y---+---r--R170
MAXIMUM CRUISE
0:: 160 ~F---b~H---r--t--I::I160 0::
~
ll.. 150 -+---11=1150
~
ll..
W w
o~ 140 --r-H14O 0
~
::J: ::J:
W w
~ 130 ~-t-~+---r-~r-~--;;130 ~
~ ~
al 120 ~~+---~~---+---r--R120 al
90 ~ __~__+-__~~__-+__-r__~~90
80
-r--+--+---r----ir--+---r---+----t---H 80
70 -r-+--+---r---t---+--+--+--+--r--H 70
24 26 28 32 34 36
ASS. DRY MANIFLOD PRESSURE IN. HG.
CONSTANT SPEED SEA LEVEL PERFORMANCE TSI0-360-MB
-t
230
~~
I 220
i
210
1
I i I ! Lf-"'" ---+:/ : 200
I I I
I
I i I /~ ~ r't 400
'I
100
i
I / / .--/' I-""" f-I12300 1
180
/ // / ' V
~
~VV/ / / ~ . J--- w
130 i'"l
./ ~/V/ / / ~ 120
V/ V/ V/ .,/ 110
~ /~ V~V / 100
~/ / ' /V/ V 90
V// / / /V 80
V/ / 70
~ 60
i 20 22 24 26 28 30 32 34 36 38 40 42
MANIFOLD PRESSURE In Hg
I I I
CO'NTINElTAL
100% POWER PUMP PRESSURE LIMITS FOR TSIO-360-MB
(UNLESS OTHERWISE SPECIFIED)
I I I I I I
NOTE: This data to be uSl!d when checking pressure at fuel pump outlet with
gage vented to atmospheric pressure.
CHART INSTRUCTIONS:
1. Obtain actual maximum rated RPM
2. Determine fuel pressure limits for 100% maximum power by reading directly
above actual maximum rated RPM point.
~ i
E
~ EXAMPLE:
E 100% Power Fuel Pump Pressure Limits @ 2700 ± 10 RPM, 280-320 psig.
f=
1= NOTE: Idle (700 ± 25 RPM) Pump Pressure, 6.5 ± .25 pslg.
1=
l::::
~-
,
w
a::
1-33
::::> - f-32
en -- \'\\9"~
~
'(1\\\
--
en
w
:f- f-31
0-
~
::::>- 1-30
0-
--
..J
W
::::>
1.1..- 1-29
\.\(1\\\
a:: \.o'l<l~
w
~
E
~- f-28
0-
~
0
0
---
...
0 - f-27
76-00-100
III II 1111.111111 111111111 111111111 1111111111 !IIIIIIIII 1111111111 1111111111 111111111 1111111111 1111111111 111111111 111111111 1111111111 1111111111 111111111 1111111111 1111111111 1111111111 11111
F
r- F
t==
F=
F=
~
140
NOTE:
=
=
1. Continuous operation at TIT in excess 01 1650° F
=
-n / 130 =
c is prohibited. =
!!!. 2. Manual leaning permitted to minimum SFC =
-n (Appro •.. 42 Lb/Bhp-Hr) as long as 1650° F / =
==
TIT is not exceeded. Cylinder head temperature 120
~ remain below 425° F and oil temperature does =
not exceed 220°F. ::::
~ 3. Manual leaning to TIT 1550°F maximum permitted
V / 110
==
=
as long as cylinder head temperature remain below =
425°F and oli temperature does not exceed 220°F.
oD' / =
o
(!I =
./ / 100 =
V "11 =
~ c: =
0- m
~~~ r- ==
ro / V 90- - " 1 1 ==
-==
;; r-
/ </-\V
~.~~ 0 ==
==
(!I
"'" =E =
::r: ,/' v~~ / '
80- - ? -= =
V ~ /'
o = til
; .... = 0
(!I ::t
=
'0 ./
V ./ // =
o 70- -~ r--==
V V / =
~
"'I
==
=
.",.-
V /' ~ ==
(ij
v:: 60
V =
=
V NOTE 3 =
5•
w
m
/
V /' ~~ Approx. Peak TIT
50 ==
........- Approx. Minimum Specific =
oI ~ =
Full Consumption =
s:
ro
V ~ ==
~V 40
V =
NOTE 2
::::
.1 ==
~~ I 30 ==
r- 70 90 100 130 150 170 190 210 ==
=
t:::::
I I I I ~
- ~
BRAKE HORSEPOWER (Propeller Load Curve) t::
....
cp I 1 I I I I I
o UlIII III
<?
...
o
...
WJJLlII IIIIII
I
F
~
0-. =
F
...I'
0C) 1--40 ~
-- r=
u..:::t: FULL THROTTLE ADMP
ZZ I---- F
---
«:::' ~ Eo:
:i!w 1--30 ~
>a:
a:::>
0(1)
(I)
'W 1--20
(I) a:
-- PROP LOAD ADMP
~ t=
E=
~
t=
~
~
~a. ~
220
t= / / 180- t--w
a.
~
~
~ V
V
V (I)
a:
0
t= /' / 160- t--:::t:
t= V w 1=
F
F V ~ l=
t=
~ / / 140-
«
a:
t--1Il
t=
F
l=
Fe: V 0 Fe:
w F
Fe:
t= / 120- t--O
... §
t= V w
a:
Fe:
Fe:
/ a:
100- t-- 0
F
§
t-
80
~ ~
~ ..... ~
~
r= a: ~
~
:::t: r=
~
~
...I'
wa. F
F
::>:::t:
~ u..~ FULL THROTTLE BSFC ---7 ~
F 0(1) -,60 i:=
F=
~
t=
_Ill
u.....1
0;_ -,55 ./'
/ ~
~
t=
- v----
~ ~O ,/'
t=
~
~
~
(l)j::
wa.
"---r--
~ :IE- -,50
~ «::>
F a: (I) PRO~ LOAD, BSFC
~ IIlZ F
§ 0 i:=
F
F ~ 2000 2100 2500 2600 2700
22,00 23,00 24,00
Eo:
t=
Eo:
t= IENGINIE RPM
1
illllllill 111111111111 W1l lill lUill
76-00-102
w-'
u~·
Zu
,--- «w
21.1.
ccu.
OUJ I I
LL.
r-- CCo z
w _
"-I-
0«
t----
UJ..J -
..J..J
..J«
«I-
I-C/l
C/lZ
t---- Z-
-0
..JI-
«I-
1--- Uu
-UJ --P'- --- ;:1;- 1----
r---+---II V/ / / / / V/ / V
"-,
>-ro
1-::;,
/
-- / ~--*" --
~~
1----
- - f-- / / 0
N
~I/ / V V
/ j/ /
rV(S V / V/ _1/ Vr --- -~----
I---T-
~ --~ ~---T--
~--
&/
--
I -,--'#;
lit! 7 f
~\ /
&
L
I-
v
&/
/
/
;{ V
j/ 1/
/ / v __
~
;::--~-
~-'E--
~
§
~
"-
"'"
:::!
__ .. _
~ 1/
\Y I II 7 ~
-t
4:
\\ v / / /
v to --
~\ :):.
/ /I
I ....
i~\
t / / N
0
N
0
0
0
V0
/ I
II
....
0 0 0 0 0 0
.... 0
0
~ ~ 0
N 00 N
N N
'I 'I 'I '"
Brake Horsepower
I I
76-00-103
'""-I I I I I I I I I II
0>
0
I
0I
- I
NOTE:
I I I I I I I
I
I
I
-
-..J
0'>
0
I
- ::-
I
NOTE:
I
I
I I
I
I
I I
I
I
I I
I
I
I
I I
I I LLLJ 11111 III
:
0I
..... f- 1) FULL RICH MIXTURE ABOVE 165 BHP
-
0
0'> 2} 1650 TIT OR PREK TIT BELOW 165 BHP
--
3} CORRECT BHP FOR INLET AIR TEMPERATURE AS FOLLOWS:
--
;::u -
m f-
a) ADD 1% FOR EACH 6°F BELOW Ts
< : b) SUBTRACT 1% FOR EACH 6°F ABOVE Ts
--
(/) I- :
m -
0 240
0 :
() -
-I ~ --
!:!:
co ....C 220 r
-..J Q.
:
CD 36 IN. HG. MANIFOLD PRESSURE -
." :
CD 200 34
~
-
~ ~r 32
:
3 =" :
I» 180
::s 0::: 30 ~
(')
--
CD W -
I\) 3: 28
U1 0 160
0
""" "-....... =
S;;
0 D..
W 26
::0 U) r"
." 0::: :-
== 0 140 24
J: ~
;! W :=
(5 ~ 22
~ ~ 120 r
0 m
i: .--20 -:=
j:u 100
r - -
en
m ~
- - :
--- ---
80
.---- ----
I-
---
--
60 - --
I
1 I I
-
I II IIIII III II IIIII II I I I IIIII 11111 I II II I II II 11111 II I I I II II I 11111 I I I II II II I III
o 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30
DENSITY ALTITUDE X 1000 FEET
NOTE:
1) FULL RICH MIXTURE ABOVE 165 BHP
2) 1650 TIT OR PREK TIT BELOW 165 BHP
3) CORRECT BHP FOR INLET AIR TEMPERATURE AS FOLLOWS:
a) ADD 1% FOR EACH 6°F BELOW Ts
b) SUBTRACT 1% FOR EACH 6°F ABOVE T5
220
36 IN. HG. MANIFOLD PRESSURE
.........
200
- 34
3' c-.....
.........
180 30
0::
~
w
3:
0
0-
w
160
- 28
26
~ 24
0 140
::t:
w 22
- --
~ I""""
~ 120
al 20
100
~
I--
80
60
o 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30
DENSITY ALTITUDE X 1000 FEET
TSIO-360-MB
240
220
200
r-
LnHv
--138bHg
3a~Hg
I" .....
32lnHg
i
I
:::::.
-- i
...........
~I
i
I
~
i
"'-
"" .... I
!
!
I I
!
I
-"\
-
180
i
Ii ....... I i
'~" 160 -
-
,
fu
~"'- r-
~ L..---r-
~
III
140
-- f.-- ~
~
"!.-... - r-
-
120
f.-- ~ r-
100
:?!-"'- f.--
~
r--
80
4 10 12 14 16 18 20 22 24 28
DENSIlY AI.TITUDE X 1000 FT.
TSIO·360-SB
E §
NOTE:
~
1) FULL RICH MIXTURE
ABOVE 165 BHP -
E 2) 1650 TIT OR PEAK TIT
BELOW 165 BHP
> 3) CORRECT BHP FOR INLET AIR
::;: TEMPERATURE AS FOLLOWS:
:::;: Ei-- 1-240 a) Add 1% for each 6°F below Ts
c b) Subtract 1% for each 6°F above Ts
a. I
CD
'------ 1-220 36 IN. HG. MANIFOLD PRESSURE
'tI
CD 34
a- '------ 1-200
- 32
-~
'"'I
3 30
Q) ~
-ffi 1-180
::l
o
CD 0
~
28
-
11. 26 ~
,W 1-160
~ VI
II:
0 - 24
8 _:I: 1-140 -
--
::xJ w -
'tI :.: 22
3: -:li" ~120
- · f - - - 1-
20
I
~ r--- E
- 1-100
9w
en 80
- --- - -
I? E
3:
III 60
1= 0 2 4 6 8 O 22 24 26 28 30 E
1\
E Y lj 1t it i F
JDENSlrV ALjITUD, X 1001 FEETI E
1111i11l! 1111111 1111 1111 1111
, II'
-
DEPICTION OF VARIATION OF MANIFOLD PRESSURE CRITICAL
ALTITUDE AS AFFECTED BY AMBIENT TEMPERATURE
(DEPENDENT ON FLIGHT TESTS CONDUCTED TO IDENTICAL
PROCEDURES AND CONFIGURATION.)
:::
+2
I-
UJ
zUJ
017
-Cf) +1
1-0
«z r
-~
a:Cf) ...............
«:::::>
>0 ~
WI
01-
:::::>-
----......r--....
0
I-W
-0 -..............
1-:::::>
, ...J I-
«-
----......r--....
...JI-
«...J I:::: --.........
u~ ~
->-
1-1- -1
t-
r--....
a:-
uCf) ...............
z
UJ ............... ~
0
~
-2
c::
1111: 11
-
-20 -10 o +10 +20 +30 +40
AMBIENT TEMPERATURE
OF DELTA FROM "T" STANDARD
76-00-109
INTENTIONALLY
LEFT
BLANK
76-00-110
CHAPTER 77
ENGINE INDICATING
77-00-00 GENERAL
77-10-00 OPERATING
77-20-00 ENGINE TROUBLESHOOTING CHART
77-00-01
INTENTIONALLY
LEFT
BLANK
77-00-02
77-00-00 GENERAL
1. The following magnetos equipped with an appropriate harness are eligible on these
engines at the indicated weight change.
wt. Change
Two Bendix S6RN-25 +1 lb.
Two Bendix S6LN-25 +1 lb.
Two Slick Electro Model 6224 -3 lb.
The following spark plugs are approved for use in engines covered in this manual.
ALL MODELS
Manufacturer Manufacture PLN TCM PIN Manufacturer Manufacture PlN TCM PIN
ACCESSORY DATA
Magneto CW 1.51 :1
Alternator CCW 2.035:1
Propeller Gov. ** CW 1:1
Fuel Injection Pump CCW 1:1
Vacuum Pump Pad*** CCW 1.545:1
Compressor Drive
(Optional) CW 1.5:1
Alternator
(Optional) CW 3.25:1
77-00-03
SB77-10-00 OPERATING LIMITS
• TSIO-360-MB .......................................................................................................
TSIO-360-SB ........................................................................................................
Idle RPM
TSIO-360-A,AB,B,BB,C,CB,D,DB,H,HB,JB ......................................................... 600
TSIO-360-E,EB,F,FB,GB,KB,LB,MB,SB ............................................................. 700
210 @ 2700
220 @ 2600
•
TSIO-360-MB ....................................................................................................... 125-135
TSIO-360-SB ........................................................................................................ 136-148
Fuel Pump Pressure at Full Throttle (PSI)
TSIO-360-A,AB,B,BB ........................................................................................... 27.0-31.0
TSIO-360-C,CB,D,DB .......................................................................................... 34.0-37.0
LlTSIO-360-E,EB ................................................................................................. 43.0-46.0
TSIO-360-F,FB ..................................................................................................... 43.0-46.0
TSIO-360-GB ....................................................................................................... 45.0-49.0
TSIO-360-H,HB .................................................................................................... 29.0-33.0
TSIO-360-JB ........................................................................................................ 34.5-37.5
LlTSIO-360-KB ..................................................................................................... 36.0-39.0
TSIO-360-LB ........................................................................................................ 34.0-38.0
• TSIO-360-MB .......................................................................................................
TSIO-360-SB ........................................................................................................
Fuel Pump Pressure at Idle (PSI)
TSIO-360-A,AB,B,BB,C,CB,D,DB,H,HB,JB .........................................................
LlTSIO-360-E,EB,K,KB ........................................................................................
28.0-32.0
31.0-36.0
6.5-7.5
6.5±.25
TSIO-360-F,FB,GB,LB ......................................................................................... 6.5±.25
TSIO-360-MB ....................................................................................................... 6.5±.25
Metered Fuel Pressure at Full Throttle (PSI)
TSIO-360-A,AB,B,BB ........................................................................................... 15.5-17.0
TSIO-360-C,CB,D,DB .......................................................................................... 17.0-19.0
LlTSIO-360-E,EB ................................................................................................. 16.0-18.0
TSIO-360-F,FB ..................................................................................................... 16.0-18.5
TSIO-360-GB ....................................................................................................... 17.0-19.0
TSIO-360-H,HB .................................................................................................... 15.3-17.2
TSIO-360-JB ........................................................................................................ 17.0-19.0
LlTSIO-360-KB ..................................................................................................... 18.0-21.0
TSIO-360-LB ...................................................................................... .................. 15.0-16.0
Max. Oil Consumption (Lb-/BHP/Hr. Max. at Rated Power at RPM) .006 Ibs.x % Power
All TSIO-360 .......................................................................................................... 100
Oil Temperature (Max) .................................................................................................................. 240°F
All TSIO-360
This troubleshooting chart is provided as a guide. Review all probable causes given, check
other listings of troubles with similar symptoms. Items are presented in sequence of the
approximate ease of checking, not necessarily in order of probability.
Engine Will Not Start Fuel tank empty. Fill with correct grade fuel.
Engine Will Not Run At Propeller levers set in high Use low pitch (INCREASE RPM)
At Idling Speed pitch (DECREASE RPM). position for all ground operations.
Mixture levers set for im- Use FULL RICH position for all
proper mixture. ground operation, except high
altitude airports.
77-00-00
77-20-00 ENGINE TROUBLESHOOTING (Continued)
Rough Idling (cont'd) Hydraulic lifters fouled. Remove and clean lifters. Inspect
and clean oil filter at more
frequent intervals.
Engine Runs Too Lean Improper manual leaning Refer to Chapter 76 for proper
At Cruising Power procedure. fuel flow settings.
Fuel flow reading too low. Check fuel strainer for clogging.
Clean screen.
Engine Runs Too Rich Restriction in air intake Check passages and remove
At Cruising Power passages. restrictions.
Engine Runs Too Lean Fuel injection malfunction. See Troubleshooting, Fuel
Or Too Rich At Injection System.
Throttle Setting Other
Than Cruise
Continuous Fouling Of Piston rings excessively worn Replace rings. Replace cylinder
Spark Plugs or broken. if damaged.
Piston rings are not seated. Hone cylinder walls, replace rings.
Engine Runs Rough At Loose mounting bolts or Tighten mounting bolts. Replace
High Speed damaged mount pads mounting pads.
77-00-07
77-20-00 ENGINE TROUBLESHOOTING (Continued)
Sluggish Operation And Throttle not opening wide. Check and adjust linkage.
Low Power (See Rigging of Mixture and
Throttle Controls).
High Cylinder Head Low octane fuel. Drain tanks and replace with
Temperature correct grade of fuel.
High Cylinder Head Exhaust system gas leakage. Locate and correct.
Temperature
Exhaust valve leaking. Repair cylinder.
77-00-08
77-20-00 ENGINE TROUBLESHOOTING (Continued)
Rough Idle At Mixture too rich. Pull mixture control back to where
Airfields with Ground where the engine operates the
Elevation of 3500 Feet smoothest at IDLE RPM.
Or Higher
Slow Engine Mixture too rich. Adjust mixture per Chapter 76.
Acceleration At
Airfields With A
Ground Elevation Of
3500 Feet Or Higher
Engine Will Not Stop Fuel manifold valve not Repair or replace manifold valve.
At Idle Cut-Off seating tightly.
High Engine Idle Fuel manifold valve sticking Repair or replace manifold valve.
Pressure Impossible closed.
To Obtain
Fuel manifold valve vent Repair or replace manifold valve.
obstruction.
Erratic Engine Fuel manifold valve sticking, Repair or replace manifold valve.
Operation or not free.
Low Fuel Pressure Restricted flow to fuel Check mixture control for full
metering valve. travel. Check for restrictions
in fuel filters and lines, adjust
control and clean filter. Replace
damaged parts.
77-00-09
77-20-00 ENGINE TROUBLESHOOTING (Continued)
Low Fuel Pressure Fuel control lever Check operation of throttle control
(Cont'd) interference. and for possible contact with
cooling shroud. Adjust as required
to obtain correct operation.
High Fuel Pressure Restricted flow beyond fuel Check for restricted fuel nozzles
control assembly. or fuel manifold valve. Clean or
replace nozzles. Replace mal-
functioning fuel manifold valve.
Fluctuating Fuel Vapor in fuel system, ex- Normally, operating the auxiliary
Pressure cessive fuel temperature. pump will clear system. Operate
auxiliary pump and purge system.
Fuel gage line leak or air in Drain gage line and tighten
gage line. connections.
Low Oil Pressure Insufficient oil in oil sump, Add oil, or change oil to proper
On Engine Gage oil dilution or using improper viscosity.
grade oil for prevailing
ambient temperature.
Leaking, damaged or loose oil Check for restricted lines and loose
line connections - Restricted connections, and for partially clogged
screen or filter. oil filter or screens. Clean parts,
tighten connections, replace
malfunctioning parts.
77-00-10
77-20-00 ENGINE TROUBLESHOOTING (Continued)
Engine Runs Rough Improper fuel-air mixture. Check manifold connections for
At Speeds leaks. Tighten loose connections.
Above Idle Check fuel control and linkage
for settings and adjustment.
Check fuel filters and screens
for dirt. Check for proper pump
pressure, and replace pump if
malfunctioning.
Engine Has Poor Idle mixture too lean. Readjust idle mixture.
Acceleration
Incorrect fuel-air mixture, Tighten loose connections, replace
worn control linkage, or worn elements of linkage, service air
restricted air cleaner. cleaner.
77-00-11
INTENTIONALLY
LEFT
BLANK
77-00-12
CHAPTER 78
EXHAUST
78-00-00 GENERAL
78-00-01
INTENTIONALLY
LEFT
BLANK
78-00-02
78-00-00 GENERAL
I
78-10-00 EXHAUST SYSTEM
Turbocharger Temperature
TSIO-360-A,AB, B,BB, C,CB D,DB, E,EB, H,HB, JB, LB, MB, SB
Continuous ............................................................................................ 1650°
Peak -30 Second Limit ......................................................................... 1700°
Exhaust Pressure at Turbine Outlet Inches Hg. Gauge 2.0 In. Hg.
Above Ambient
This troubleshooting chart is provided as a guide. Review all probable causes given, check
other listings of troubles with similar symptoms. Items are presented in sequence of the
approximate ease of checking, not necessarily in order of probability.
Engine Lacks Power, Improperly Adjusted Wastegate To check the adjustment of the
Reduction In Maximum valve. wastegate valve, refer to the
Manifold Pressure at airframe service manual.
Critical Altitude
White Smoke Exhaust Turbo choking, oil forced Clean or change turbocharger.
though seal turbine housing.
78-00-04
CHAPTER 79
OIL
79-00-00 GENERAL
79-00-01
INTENTIONALLY
LEFT
BLANK
79-00-02
79-00-00 GENERAL
Use only lubricating oils conforming to TCM specifications. The marketers of the aviation
lubricating oils listed below have supplied data to TCM indicating their products conform to
all the requirements set forth by TCM.
In listing the products names, TCM makes no claim of verification of marketer's statements
or claims. Listing is made in alphabetical order and is provided only for the convenience of
the users.
CAUTION. .. The airframe manufacturer furnishes certain parts which depend on engine oil
for lubrication and may restrict the use of some lubricating oils.
I
79-10-00 APPROVED ASHLESS DISPERSANT OILS:
NOTE ... The operator using an oil service is reminded that an oil analysis does not reveal all abnormal
engine conditions. It should not be used as a replacement or substitute for routine maintenance and
inspection procedures recommended in the Operators Manual, Service Bulletins, or other directives. For
further information, see TCM Service Bulletin M81-5 or current revisions as applicable.
This troubleshooting chart is provided as a guide. Review all probable causes given, check
other listings of troubles with similar symptoms. Items are presented in sequence of the
approximate ease of checking, not necessarily in order of probability.
Oil viscosity too high. Drain and refill with correct seasonal
weight. (See Chapt. 77)
Low Oil Pressure Low oil supply. Oil viscosity Replenish. Drain and refill with
Indication too low. correct seasonal weight. (See Chapter 77)
Foam in oil due to presence Drain and refill with fresh oil. (It
of alkaline solids in system. may be necessary to flush cooler core
if presence of alkaline solids is due
to previous cleaning with alkaline
materials).
79-00-04
CHAPTER 80
STARTING
80-00-00 GENERAL
80-00-01 Prestarting
80-00-02 Starting
80-00-07 Preheating
80-00-01
INTENTIONALLY
LEFT
BLANK
80-00-02
80-00-00 GENERAL
The life of your engine is determined by the care it receives. Follow the instructions
contained in this manual carefully.
The engine received a run-in operation before leaving the factory, therefore, no break-in
schedule is required. Straight mineral oil (MIL-C-6529 Type II) should be used for the first
oil change period (25 hours).
The minimum grade aviation fuel for this engine is 100LL (Blue) or 100 (Green). If the
minimum grade required is not available, use a higher rating. Never use a lower rated fuel.
WARNING ... The use of a lower octane rated fuel can cause pre-ignition and/or detonation
which can damage an engine the first time high power is applied, possibly causing engine
failure. This would most likely occur on takeoff. If the aircraft is inadvertently serviced
with the wrong grade of fuel, then the fuel must be completely drained and the tank properly
serviced, prior to engine operation.
NOTE... The following checklists are general in nature, since the various airframe/powerplant
combinations are not necessarily the same setup and layout. Consult your own pilot's
operating handbook for the specific challenge and response checklists required for your
aircraft.
80-00-01 PRESTARTING
Before each flight the engine and propeller must be examined for damage, oil leaks, security
and proper servicing.
2. Operate all controls and check for binding and full range of travel.
3. Assure that fuel tanks contain proper type and quantity of fuel. (1 DOLL-Blue or
100-Green).
4. Drain a quantity of fuel from all sumps and strainers into a clean container. If
water or foreign matter is noted, continue draining until only clean fuel appears.
80-00-03
80-00-02 STARTING
Before each flight the engine and propeller MUST be examined for damage, oil leaks,
security and proper servicing.
Release the Magneto/Start Switch to BOTH position as soon as the engine starts.
CAUTION. .. Do not engage the starter when the engine is rnnning, as this will damage
the starter. Do not crank for longer than thirty seconds at a time, as this may cause
the starter motor to overheat. If the engine does not start after thirty seconds of
cranking, allow a 3 to 5 minute cooling period before attempting to restart.
CAUTION. . . If engine kicks back when starting, DO NOT attempt to start. The
ignition starting system is inoperative and must be repaired before damaging starter
adapter assembly.
12. Use the same procedure to start other engine, if operating a twin engine installation.
Teledyne Continental aircraft engines are aircooled and are dependent on the forward speed of
the aircraft for cooling. To prevent overheating, it is important that the following rules be
observed.
2. Operate the engine on the ground with the propeller in "Full Increase" RPM
position.
3. Avoid prolonged idling at low RPM. Fouled spark plugs can result from this
practice.
80-00-04
4. Leave mixture in "Full Rich". (See "Ground Operation at High Altitude Airports",
Section 80-00-09 for exceptions).
1. Maintain engine speed at approximately 900 to 1000 RPM for at least one minute in
warm weather, and as required during cold weather, to prevent cavitation in the oil pump
and to assure adequate lubrication.
CAUTION. . . Do not operate the engine at mn-up speed unless oil temperature is 75°P.
minimum and oil pressure is within specified limits of 30-60 PSI.
3. Perform all ground operations with cowling flaps, (if installed), full open, with
mixture control in "FULL RICH" position, dependent on field elevation, and propeller
control set for maximum RPM (except for brief testing of propeller governor).
4. Restrict ground operations to the time necessary for warm-up and testing.
5. Increase engine speed to 1700 RPM only long enough to perform the following
checks:
A. Magnetos: With both magnetos "ON", position the right magneto switch "OFF" and note
engine RPM; now back to both magnetos "ON" to clear the spark plugs. Then position the
left magneto switch "OFF" and note engine RPM. Now return switch to both magnetos "ON".
The allowable difference between the maximum drop for each magneto is 150 RPM. Observe
engine for excessive roughness during this check.
If no drop in RPM is observed when operating on either magneto alone, switch circuit should
be inspected.
WARNING ... Absence of RPM drop when checking magnetos may indicate a malfunction in
the ignition circuit. This type of malfunction should be corrected prior to continued operation
of the engine. Should the propeller be moved by hand (as during preflight) the engine may
start and cause injury to personnel.
80-00-05
Minor spark plug fouling can usually be cleared as follows:
(3) Mixture - Move toward idle cutoff until RPM peaks and hold for ten seconds.
Return mixture to full rich.
If engine is not operating within specified limits, it should be inspected and repaired prior to
continued operational service.
Avoid prolonged single magneto operation to preclude fouling of the spark plugs.
Move propeller governor control toward low RPM position and observe tachometer. Engine
speed should decrease to minimum governing speed (200-300 RPM drop). Return governor
control to high speed position. Repeat this procedure two or three times to circulate warm
oil into the propeller hub.
Where applicable move propeller control to "Feather" position. Observe for 300 RPM drop
below minimum governing RPM, then return control to "Full Increase" RPM position.
CAUTION. . . Do not operate the engine at a speed in excess of 2000 RPM longer than
necessary to test operation and observe engine instmments. Proper engine cooling depends
upon forward speed of the aircraft. Discontinue testing if temperature or pressure limits are
approached.
1. Instrument indications.
A. Oil Pressure: The oil pressure relief valve will maintain pressure within the specified
limits if the oil temperature is within the specified limits and if the engine is not excessively
worn or dirty. Fluctuating or low pressure may be due to dirt in the oil pressure relief valve
or congealed oil in the system. This should be corrected prior to continued operation of the
engine.
B. Oil Temperatures: The oil cooler and oil temperature control valve will maintain oil
temperature within the specified range unless the cooler oil passages or air channels are
blocked, leading to rapid wear of moving parts in the engine.
C. Cylinder Head Temperature: Any temperature in excess of the specified limit may cause
cylinder or piston damage. Proper cooling of cylinders depends on cylinder baffles being
properly positioned on the cylinder heads and barrels, and other joints in the pressure
compartment being tight to force air between the cylinder fins. Proper cooling also depends
on operating practices. Fuel and air mixture ratio will affect cylinder temperature. Exces-
sively lean mixture causes overheating even when the cooling system is in good condition.
High power and low air speed, or any slow speed flight operation, may cause overheating by
reducing the cooling air flow. The engine depends on the ram air flow developed by the
forward motion of the aircraft for proper cooling.
80-00-06
D. Battery Charging: The ammeter should indicate a negative charging rate while the
engine is being started. The ammeter reading should return to the positive side as soon as
the engine starts and RPM increases. A low charging rate is normal after the initial recharg-
ing of battery. A zero reading or negative reading with electrical load may indicate a
malfunction in the alternator or regulator system.
4. As the engine starts, return the Magneto/Start Switch to BOTH. Retard the throttle and
slowly advance the mixture control to FULL RICH position.
NOTE. . . Prior to operation and/or storage in cold weather assure engine oil viscosity is
SAE 30, 10W30, 15W50 or 20W50. In the event of temporary cold weather operation not
justifying an oil change to SAE 3D, consideration should be given to hangaring the aircraft
between flights.
Engine starting during extreme cold weather is generally more difficult than during warm
weather conditions. Cold soaking causes the oil to become thicker (more viscous), making it
more difficult for the starter to crank the engine. This results in a slow cranking speed and
an abnormal drain on the battery capacity. At low temperatures, gasoline does not vaporize
readily, further complicating the starting problem.
CAUTION. . . During cold weather operation fuel vaporization characteristics are poor.
Mismanagement of the auxiliary fuel pump or overpriming of the engine could lead to cylinder
hydro-static lock.
False starting (failure to continue running after starting) often results in the formation of
moisture on the spark plugs due to condensation. This moisture can freeze and must be
eliminated either by applying heat to the engine or removing and cleaning the spark plugs.
80-00-07 PREHEATING
The use of preheat and auxiliary power unit (APU) will facilitate starting during cold weather
and is recommended when the engine has been cold soaked at temperatures of 30°F. and below
in excess of 2 hours. Successful starts without these aids can be expected at temperatures
below normal, provided the engine is in good condition and the ignition and fuel systems are
properly maintained.
The following procedures are recommended for preheating, starting, warm-up, run-up and
takeoff.
1. Select a high volume hot air heater. Small electric heaters which are inserted into
the cowling opening do not appreciably warm the oil and may result in superficial
preheating.
80-00-07
A minimum of preheat application may warm the engine enough to permit starting but will not
de-congeal oil in the sump, lines, cooler, filter, etc. Congealed oil in such lines may require
considerable preheat. The engine may start and apparently run satisfactorily, but can be
damaged from lack of lubrication due to congealed oil in various parts of the system. The
amount of damage will vary and may not become evident for many hours. On the other hand,
the engine may be severely damaged and could fail shortly following application of high power.
Proper procedures require thorough application of preheat to all parts of the engine. Hot air
should be applied directly to the oil sump and external oil lines as well as the cylinders, air
intake and oil cooler. Excessive hot air can damage nonmetallic components such as seals,
hoses and drive belts, so do not attempt to hasten the preheat process.
Before starting is attempted, turn the engine by hand or starter until it rotates freely.
After starting, observe carefully for high or low oil pressure and continue the warm-up until
the engine operates smoothly and all controls can be moved freely. Do not close the cowl
flaps to facilitate warm-up, as hot spots may develop and damage ignition wiring and other
components.
2. Hot air should be applied primarily to the oil sump and filter area. The oil drain
plug door or panel may provide access to these areas. Continue to apply heat for 15 to
30 minutes and turn the propeller, by hand, through 6 or 8 revolutions at 5 to 10 minute
intervals.
3. Periodically feel the top of the engine, and when some warmth is noted, apply heat
directly to the upper portion of the engine for approximately five minutes. This will
provide sufficient heating of the cylinders and fuel lines to promote better vaporization
for starting. If enough heater hoses are available, continue heating the sump area.
Otherwise, it will suffice to transfer the source of heat from the sump to the upper part
of the engine.
4. Start the engine immediately after completion of the preheating process. Since the
engine will be warm, use normal starting procedure.
NOTE. . . Since the oil in the oil pressure gage line may be congealed, as much as 60
seconds may elapse before oil pressure is indicated. If oil pressure is not indicated
within one minute, shut the engine down and determine the cause.
5. Operate the engine at 1000 -RPM until some oil temperature is indicated. Monitor
oil pressure closely during the time and be alert for a sudden increase or decrease.
Retard throttle, if necessary to maintain oil pressure below 100 psi. If oil pressure drops
suddenly to less than 30 psi, shut down the engine and inspect the lubrication system.
If no damage or leaks are noted, preheat the engine for an additional 10 to 15 minutes
before restarting.
6. Before takeoff, run up the engine to 1700 RPM. If necessary approach this RPM in
increments to prevent oil pressure from exceeding 100 psi.
At 1700 RPM, adjust the propeller control to Full Decrease RPM until minimum governing
RPM is observed, then return the control to Full Increase RPM. Repeat this procedure three
or four times to circulate warm oil into the propeller dome. If the aircraft manufacturer
recommends checking the propeller feathering system, move the control to the Feather
position, but do not allow the RPM to drop more than 300 RPM below minimum governing
speed.
80-00-08
7. Check magneto in the normal manner.
8. When the oil temperature has reached 100°F. and oil pressure does not exceed 80
psi at 1700 RPM, the engine has been warmed sufficiently to accept full rated power.
NOTE. . . Fuel flow will probably be on the high limit; however, this is normal and desirable
since the engine will be developing more horsepower at substandard ambient temperatures.
If preheat is not used, employ the same start procedures for a normal start, except:
1. At temperatures below +20°F., continue priming while cranking until engine starts.
2. When engine starts and accelerates thru 500 RPM, release Starter.
4. Release primer.
6. Oil Pressure - Check. If none noted within 30 seconds, shut down engine and
investigate.
Observe oil pressure for indication and warm-up engine at 1000 RPM. Ground operation and
run-up require no special techniques other than warming the engine sufficiently to maintain
oil temperature and oil pressure within limits when full RPM is applied.
NOTE. . . Before applying power for takeoff, assure that oil pressure, oil temperature and
cylinder head temperature are well within the normal operating range. When full power is
applied for takeoff, assure that oil pressure is within limits and steady.
Any of the following engine conditions should be cause for concern, and are justification to
discontinue the takeoff.
4. Engine roughness.
CAUTION. .. When operating in hot weather areas, be alert for higher than normal levels of
dust, dirt or sand in the air. Inspect air filters frequently and be prepared to clean or
replace them if necessary. Weather conditions can lift damaging levels of dust and sand high
above the ground. If the aircraft is flown through such conditions, an oil change is recom-
mended as soon as possible. Do not intentionally operate the engine in dust and/or sand
storms. The use of dust covers on the cowling will afford additional protection for a parked
aircraft·
80-00-09
Flight operation during hot weather usually presents no problem since ambient temperatures at
flight altitudes are seldom high enough to overcome the cooling system used in modern
aircraft design. There are, however, three areas of hot weather operation which will require
special attention on the part of the operator. These are: (1) Starting a hot engine (2)
Ground operation under high ambient temperature conditions and (3) Takeoff and initial
climbout.
The state of the fuel itself can affect these fuel vapor conditions. Fresh fuel contains a
concentration of volatile ingredients. The higher the concentration, the more readily the
fuel will vaporize and the problem with the vapor in the fuel will be more severe. Time,
heat or exposure to altitude will "age" aviation gasoline causing the volatile ingredients
to dissipate. This reduces the tendency of fuel to vaporize and may induce problems
with starting. If the volatile condition reaches a low enough level, starting may become
difficult due to poor vaporization at the fuel nozzles since the fuel must vaporize in
order to combine with oxygen in the combustion process.
The operator, by being aware of these conditions, can take certain steps to cope with
problems associated with hot weather/hot engine starting. The primary objective should
be that of permitting the system to cool. Lower power settings during the landing
approach, when practical, will allow some cooling prior to the next start attempt.
Reducing ground operating to a minimum is desired to keep engine temperatures down.
Cowl flaps should be opened fully while taxiing. The aircraft should be parked so as to
face into the wind to take advantage of the COOling affect. Restarting attempts will be
the most difficult from 30 minutes to one hour after shutdown. Following that interval
the fuel vapor will be less pronounced and normally will present less of a restart
problem.
CAUTION. . . Reduced engine power will result from higher density altitude associated
with high temperature.
80-00-10
80-00-09 GROUND OPERATION AT HIGH ALTITUDE AIRPORTS.
Because of insufficient air density at altitudes, oil pressure, oil temperatures and cylinder
head temperature gages should be carefully observed to prevent engine overheating.
80-00-11
INTNTIONALLY
LEFT
BLANK
80-00-12
CHAPTER 81
TURBINES
81-00-00 GENERAL
81-10-00 TURBOCHARGER
81-30-00 CONTROLLER
81-00-01
81-00-00 GENERAL
The purpose of the turbocharger system is to enable the aircraft engine to maintain constant
sea-level induction air pressure at higher altitudes where ambient air pressure is decreased.
The basic turbocharger system consists of four (4) main components: 1) turbocharger, 2)
wastegate and actuator, 3) controller and 4) overboost pressure relief valve, except on engine
models utilizing fixed orifice wastegates which do not require an actuator or controller. The
turbocharger turbine is driven by engine exhaust gases. As the turbine wheel rotates, the
compressor wheel is driven by a common shaft connected to both wheels. As the compressor
wheel rotates, air is compressed and routed to the induction system. The compressed air is
then mixed with atomized fuel just before entering the cylinder combustion chamber. The
amount of air allowed to enter is controlled by the engine's throttle valve, located between
the turbocharger compressor and engine cylinders. The induction system area, between the
turbocharger compressor and the throttle valve, is referred to as upper deck. The speed of
the turbocharger turbine is determine by the amount of incoming exhaust gases. This is
controlled by the wastegate of which there are two different types that will be discussed
later. The variable absolute pressure controller regulates the engine oil pressure that is
routed to the wastegate valve, except on those engine models utilizing the fixed orifice
waste gate that maintains a constant turbine r.p.m. throughout engine operation. In order to
prevent an overboost condition in the induction system, an overboost pressure relief valve is
installed. Some engine models that are used on pressurized cabin, high, altitude aircraft,
utilize an intercooler which cools compressor discharge air and decreases the possibility of
detonation. Cabin pressurization is obtained through the use of a sonic venturi. The sonic
venturi is a calibrated orifice that bleeds off some of the compressor discharge air, which is
then used to pressurize the aircraft's cabin.
AFTERCOOLER
TURBINE
OVERBOOST
THROTTLE
MANIFOLD - _ _.p;;:.~~
PRESSURE ~rr""~lJf-_-./ HYDRAULIC
WASTEGATE
'p:::======::r-.... MAGNETO
PRESSURIZATION
CONTROLLER
OIL
IN
. . EXHAUST
o COMPRESSED AIR
81-00-02 "
81-10-00 TURBOCHARGER
The turbocharger is a device that utilizes otherwise wasted overboard exhaust gases to
provide compressed air to the engine induction system. It is a relatively simple device
consisting of a turbine wheel and a compressor connected by a center housing which contains
the turbocharger lubrication system, oil seals and bearings. Connections are provided on the
center housing for engine supplied lubricating oil. For overhaul approval pertaining to the
turbocharger, refer to the turbocharger manufacturer's instructions.
81-20-00 WASTEGATES
The wastegate is used to adjust the amount of incoming exhaust gases to the turbocharger
turbine. There are two different types used on TSIO-360 Series. They are: fixed orifice
wastegate, and the butterfly valve type hydraulic wastegate.
81-00-03
1. Fixed Orifice Wastegate
The fixed orifice wastegate is a ground adjustable bypass valve located in the turbine
exhaust bypass duct. The position of the fixed orifice wastegate valve remains constant
throughout all modes of engine operation. An overboost pressure relief valve is used
with the fixed orifice wastegate valve to bleed off upper deck pressure that exceeds the
limits set by the airframe manufacturer.
A. Adjust the exhaust bypass valve bolt all the way in turning in a clockwjse
(CW) direction and reposition appraxirnately ten (10) turns out (CCW) (8-10 threads
showing outside locknut). Lock in place with the check nut. Run engine to check
full throttle manifold pressure (refer to Chapter 77). Make fine adjustments to
achieve the proper valve, clockwise to increase counter-clockwise to decrease.
Safety wire when complete.
CAUTION ... Do not exceed maximum rated power manifold pressure as listed in Chapter
77.
81-00-04
2. Hydraulic Wastegate
The hydraulic wastegate consists of a butterfly type bypass valve located in the turbine
exhaust ducting. The wastegate valve is controlled by a spring loaded hydraulic
wastegate actuator. The actuator is operated by engine oil pressure. The hydraulic
wastegate actuators consist of a movable piston and spring. Engine oil pressure against
the piston will close the wastegate increasing turbocharger turbine speed. As oil
pressure against the piston is reduced, the spring will open the wastegate, reducing
turbocharger turbine speed (See Fig. 81-20-01 Hydraulic Wastegate). The oil pressure
operating the wastegate actuator is controlled by a wastegate controller. The
hydraulically actuated wastegate systems also use an overboost pressure relief valve as a
precautionary measure.
NOTE... Hydraulic wastegates are not field serviceable or adjustable devices and should
be replaced when found to be malfunctioning.
SPRING
PISTON
81-30-00 CONTROLLER
The variable pressure controller senses upper deck pressure and regulates the wastegate
actuator. Engine oil flows from the engine to the wastegate actuator and from the actuator
to the absolute pressure controller. An oil restrictor controls the oil flow back to the engine,
by restricting the oil return to the engine the wastegate actuator is forced closed, thereby
increasing turbine speed. The oil restrictor is controlled by an aneroid bellows that is
referenced to upper deck pressure. When upper deck pressure drops below a specific pre-
determined level, the aneroid bellows closes the oil restrictor. When upper deck pressure
exceeds the specific predetermined pressure inside the bellows, the bellows expands causing
the oil restrictor to open, allowing oil to return to the engine. This in turn relieves pressure
on the wastegate piston allowing the wastegate valve to open by spring pressure, thereby
decreasing turbine speed.
81-00-05
A cam connected to the throttle mechanism, applies pressure to the end of the aneroid. For
example, as the throttle is opened, the cam rotates, applying pressure to the aneroid,
increasing the amount of upper deck pressure necessary to open the oil restrictor. When the
throttle is closed. The opposite occurs. In this manner, upper deck pressure will increase or
decrease in a direct relationship to the throttle angle.
With the variable absolute pressure controller, upper deck pressure is maintained at ap-
proximately one to two inches above manifold pressure. Maintaining this relatively low
differential between manifold and upper deck pressures reduces the load on the turbocharger
and throttle valve.
NOTE. . . Controllers are not field serviceable and should be replaced when found to be
malfunctioning.
OIL RETURN
TO ENGINE
81-00-06
81-40-00 TURBOCHARGER LUBRICATION SYSTEM
Engine lubricating oil is also supplied to the turbocharger center housing where it is used to
cool the unit and lubricate the bearings. Because of the location of the turbocharger unit on
some installations, one-way check valves are needed in the oil supply and return lines to
prevent engine oil from draining into the turbocharger when the engine is not in use.
If the turbocharger unit is located below the oil scavenge pump, one check valve is needed in
the oil return line to prevent oil from draining back into the unit. If the turbocharger is
located below the engine crankcase, check valves are required in both the oil supply and
return lines.
Piston-ring like oil seals are used on the compressor wheel shaft to prevent the lubricating oil
from entering the turbine and compressor housings from the center housing. (See Figure 81-
10-00 Basic Turbocharger).
TSIO-360-A
ACCESSORY DRIVE
tOLER SHAFT BUSHING BUSHINGS
81-00-01
81-50-00 TURBOCHARGER SYSTEM TROUBLESHOOTING CHART
This troubleshooting chart is provided as a guide. Review all probable causes given,
check other listings of troubles with similar symptoms. Items are presented in sequence
of the approximate ease of checking, not necessarily in order of probability.
Engine Oil Level Leaking Turbocharger check Replace check valves. Refer to
Frequently L&w After valves and seals. Turbocharger Manufacturer's
Servicing Prior to Instructions for turbocharger
Operation maintenance.
81-00-08
Continental Motors, Inc.
www.continentalmotors.aero