Professional Documents
Culture Documents
FAA 2019 0597 0008 - Attachment - 3
FAA 2019 0597 0008 - Attachment - 3
P/N 1795M36P02
The information contained in this document is CFM proprietary information and is disclosed in confi-
dence. It is the property of CFM and shall not be used, disclosed to others or reproduced without the
express written consent of CFM, including, but without limitation, it is not to be used in the creation,
manufacture, development, or derivation of any repairs, modifications, spare parts, design, or config-
uration changes or to obtain FAA or any other government or regulatory approval to do so. If consent
is given for reproduction in whole or in part, this notice and the notice set forth on each page of this
document shall appear in any such reproduction in whole or in part. The information contained in
this document may also be controlled by U.S. export control laws. Unauthorized export or re-export
is prohibited.
All technical documentation and information contained herein, with respect to assembly and disas-
sembly, cleaning, inspection methods and limits, repair methods and limits, operational limits, life
limits and the like, have been developed and approved for use with engines and parts that have been
manufactured and/or approved by CFM and that have been maintained in accordance with CFM
technical documentation and recommendations. CFM has no contractual or legal obligation for, nor
knowledge of, non-CFM-approved parts and repairs. Accordingly, this document is not intended to
apply to non-CFM-approved parts and repairs.
TRANSMITTAL INFORMATION
1. PLANNING INFORMATION
A. Effectivity
CFM56-7B27A
The rotating air high pressure turbine (HPT) front seals (seal) P/N 1795M36P02 with
the following serial numbers: GWNDN949 through GWNSE969, and GWN000CE
through GWN0990L (except serial numbers GWN08ND7, GWN0923A, GWN0971E,
GWN098A1, GWN098W6, GWN098W8, GWN098WA, and GWN0990G), which
have been removed from their original HPT disk in the field and re-assembled to a
second HPT disk with a different serial number, are affected by this Service Bulletin.
B. Description
This Service Bulletin provides removal timing for the seal P/N 1795M36P02 with the
serial numbers listed in paragraph 1.A, Effectivity. Refer to Figure 1.
C. Compliance
Category 2
CFM recommends that you do this Service Bulletin before 6,500 cycles since
assembly to a second HPT disk, if the seal was re-assembled to a second HPT disk
with a different serial number.
If the condition has exceeded the 6,500 cycles since assembly to a second HPT
disk, then replace the seal before 500 cycles or within three months from the original
issue date of this Service Bulletin, whichever comes sooner.
NOTE 1: For seals that have exceeded the 6,500-cycle threshold, the removal should
be prioritized based on the cycles since the installation to the second HPT
disk.
Impact A
This Service Bulletin is offered to improve the reliability or performance of your CFM
product, or to help prevent the occurrence of the event or condition described in this
Service Bulletin. If the operator elects not to participate in the bulletin, that decision
will be taken into consideration by CFM in evaluating future product performance
issues that may arise in the operator’s fleet.
D. Concurrent Requirements
None.
E. Reason
(1) Objective:
Replacement of the seal.
(2) Condition:
The seal may have a condition, generated during manufacturing, that could
affect the life of the seal if re-installed to a second HPT disk within the
operating life of the seal.
(3) Cause:
The affected seals have geometry variations on the air slot breakedges, which
can make the seal more sensitive to loading variations when assembled to a
second disk.
(4) Improvement:
None.
(5) Substantiation:
F. Approval
The technical content of this Service Bulletin is approved by the FAA and under the
Authority of DOA No. EASA.21J.086.
G. Manpower
J. Publications Affected
None.
K. Interchangeability
Not applicable.
2. MATERIAL INFORMATION
A. Material - Price and Availability
Lead
Qty/ Unit ($) Pkg Time
Part Number Eng Part Name Price Qty Days
1795M36P02 (1) Seal, Rotating 344,600.00 (1) 5
Air HPT Front
NOTE: Prices are provided for planning purposes and are subject to change.
(2) Other Spare Parts:
None.
(3) Consumables:
None.
C. Configuration Chart
None.
D. Parts Disposition
The seal P/N 1795M36P02, removed to accomplish this Service Bulletin, must be
sent to the following address via the Service Request system:
GE Aviation
Crescent Park Distribution Centers Inc
Attn: FOS Field Program Return
5443 Duff Drive
West Chester, Ohio, USA 45246
Report the seal and engine information to CFM Customer Support Center or Fleet
Support:
None.
3. ACCOMPLISHMENT INSTRUCTIONS
A. General
(1) Remove the suspect seal (Figure 1). Removal instructions have not changed.
Refer to the CFM56-7B ESM, 72-52-00, DISASSEMBLY.
(2) Write the word SCRAP close to the P/N and S/N markings. You can use any
method of permanent marking specified in the CFM56 SPM, 70-10-00. Return
the removed seal (Figure 1) to CFM to the address specified in paragraph
2.D., Parts Disposition and do as follows:
(a) Do a visual inspection of the seal (Figure 1) for cracks before you return
it to CFM. If there are cracks, notify CFM and also return the associated
HPT disk to CFM.
(3) Install the replacement seal (Figure 1). Installation instructions have not
changed. Refer to the CFM56-7B ESM, 72-52-00, ASSEMBLY 001.
Seal Location
Figure 1