Professional Documents
Culture Documents
Mexican Model
HCD-XB660
Dolby noise reduction manufactured under license Model Name Using Similar Mechanism HCD290/G330/XB3
from Dolby Laboratories Licensing Corporation. CD
“DOLBY” and the double-D symbol a are trade- CD Mechanism Type CDM37LH-5BD29AL
Section
marks of Dolby Laboratories Licensing Corporation. Base Unit Name BU-5BD29AL
Optical Pick-up Name KSS-213D/Q-NP
Tape deck
Model Name Using Similar Mechanism HCD-H881
Section
Tape Transport Mechanism Type TCM-220WR2
SPECIFICATIONS
Amplifier section CD player section
The following measured at AC 120/240 V, 50 Hz System Compact disc and digital audio system
DIN power output (Rated) 140 + 140 watts Laser Semiconductor laser (λ = 780 nm)
(8 ohms at 1 kHz, DIN) Emission
Continuous RMS power output (Reference) duration: continuous
170 + 170 watts Laser output Max. 44.6 µW*
(8 ohms at 1 kHz, 10% THD) *This output is the value measured at
Peak music power output (Reference) a distance of 200 mm from the
3,000 watts objective lens surface on the Optical
Pick-up Block with 7 mm aperture.
Inputs Wavelength 780 - 790 nm
PHONO IN (phono jacks): sensitivity 3 mV, impedance Frequency response 2 Hz - 20 kHz (±0.5 dB)
47 kilohms Signal-to-noise ratio More than 90 dB
MIX MIC (phone jack): sensitivity 1 mV, impedance Dynamic range More than 90 dB
10 kilohms CD DIGITAL OUT
VIDEO/MD (AUDIO) IN (phono jacks): (square optical connector jack, rear panel)
sensitivity 250 mV, impedance Wave length: 600 nm
47 kilohms Output level: –18 dBm
– Continued on next page –
Outputs
PHONES (stereo phone jack): accepts headphones of 8 ohms or more
VIDEO/MD (AUDIO) OUT (phono jacks):
voltage 250 mV, impedance 1 kilohms
MICROFILM
–2–
Downloaded from www.Manualslib.com manuals search engine
SECTION 1
SERVICING NOTES
–3–
Downloaded from www.Manualslib.com manuals search engine
SECTION 2
GENERAL
LOCATION OF CONTROLS
– Front Panel –
1 2 3 4 56 7 1 I /u (Power) button
2 DISPLAY/DEMO button
3 FILE (1-5) indicator
4 Fluorescent indicator tube
!§ 5 TUNER MEMORY button
8 6 TUNING MODE button
7 TUNER/BAND button and indicator
!¶
9 8 STEREO/MONO button
9 FUNCTION button
0 !º SUPER WOOFER button and indicator
!• !¡ H SPEED DUB button
!ª !¡ !™ CD SYNC button
!£ § EJECT button (DECK B)
!¢ ) button (CD)
!∞ ≠ AMS ± jog dial
@º !™
!§ t/CLOCK SET button
!£
!¶ REC button
!• PHONES jack
@¡ !¢ !ª GEQ (4/(/$/9) switch
!∞ @º § EJECT button (DECK A)
@¡ DIRECT PLAY (DISC 1 to DISC 5) button
@™ Cassette holder
@£ CD lid
@¢ EFFECT button and indicator
@™ @£ @¢ @∞ @∞ 0 button (CD)
@§ @¶ @• @ª #º @§ DAILY 1 button
@¶ DAILY 2 button
@• SPECTRUM ANALYZER button
#¡ @ª MUSIC/OTHERS/P FILE indicator
#º ENTER/NEXT button and indicator
#™ #¡ TUNING (–) button
#ª #™ TUNING (+) button
#£ #£ GROOVE button and indicator
#¢ VOLUME control knob
$º #¢
#∞ SUPER W MODE button
$¡ #§ 6 OPEN button (CD)
#∞ #¶ · button and indicator (CD)
#• REPEAT button
#ª SLEEP button
$º MIX MIC jack
$™ #§ $¡ MIC LEVEL control knob
$™ KARAOKE PON/MPX button
#¶ $£ NON-STOP button and indicator
$¢ LOOP button
$£
$∞ FLASH button
#•
$§ ENTER button and indicator
$¶ EDIT button
$• 1/ALL DISCS button
$ª PLAY MODE button
$¢ $∞ $§ $¶ $• $ª
–4–
Downloaded from www.Manualslib.com manuals search engine
%º %¡ %™ %£ %¢ %∞ %º WAVE button
%¡ SURROUND button
%™ P FILE MEMORY button
%£ GEQ CONTROL button
%¢ P button and indicator (DECK B)
%∞ p button (DECK B)
%§ %§ ª button and indicator (DECK B)
^™ %¶ 0 button (DECK B)
%¶ %• · button and indicator (DECK B)
^£ %ª ) button (DECK B)
^¢ %• ^º r REC button and indicator (DECK B)
^¡ p button (CD)
^™ · button and indicator (DECK A)
^∞ %ª ^£ 0 button (DECK A)
^¢ ª button and indicator (DECK A)
^§ ^∞ p button (DECK A)
^º ^§ DIRECTION button
^¡ ^¶ DOLBY NR button
^• ) button (DECK A)
^ª DISC SKIP button
&º P button and indicator (CD)
^¶ ^• ^ª &º
– Rear Panel –
7 8
–5–
Downloaded from www.Manualslib.com manuals search engine
–6–
Downloaded from www.Manualslib.com manuals search engine
SECTION 3
DISASSEMBLY
• This set can be disassembled in the order shown below.
MAIN BOARD
(Page 8)
CASE
3 case
1 three screws
(case 3TP2)
1 three screws
(case 3 TP2)
2 seven screws
(BATT3 × 6)
–7–
Downloaded from www.Manualslib.com manuals search engine
FRONT PANEL SECTION
1 wire (flat type) (21 core)
(CN205)
1 wire (flat type) (11 core)
(CN206)
2 four screws
(BVTP3 × 8)
4 eleven screws
(BVTP3 × 8)
5 power cord
7 connector
(CN105)
0 MAIN board
IC201
9 connector
(CN101)
2 connector
(CN203) 8 two screws
(BVTP3 × 8)
–8–
Downloaded from www.Manualslib.com manuals search engine
MAIN SECTION 2 connector 1 flat wire (CN202)
(CN203)
4 main section
3 two screws
(BVTP3 × 8)
3 screw
(BVTP3 × 8)
3 two screws
(BVTP3 × 8)
4 CD mechanism
deck section
(CDM37LH-5BD29AL)
2 flat wire
and lead wire
–9–
Downloaded from www.Manualslib.com manuals search engine
TAPE MECHANISM DECK SECTION (TCM-220WR2)
1 Push the
two buttons.
3 two bracket
2 two screws
(BVTP2.6 × 8)
1 two springs
– 10 –
Downloaded from www.Manualslib.com manuals search engine
CD LID ASS’Y SECTION 6 four screws
(BVTP2.6 × 8)
5 connector
(CN671)
7 CD lid ass’y
4 connector
(CN661)
2 four screws
(BVTP2.6 × 8)
3 CD-B1 SW board
1 connector
(CN642)
PANEL (A) / (B) SUB ASS’Y
1 connector
(CN612)
3 two claws
2 four screws
(BVTP2.6 × 8)
5 two claws
– 11 –
Downloaded from www.Manualslib.com manuals search engine
BASE UNIT
3 base unit
1 yoke bracket
2 boss
DISC TABLE
Note:
When the disc table is installed, adjust the positions
of roller cam and mark ( as shown in the figure,
then set to the groove of disc table.
A
3 step screw
1 screw
(BVTP3 × 8)
1 screw
2 bracket (BU) (BVTP3 × 8) 4 disc table
– 12 –
Downloaded from www.Manualslib.com manuals search engine
BD BOARD
2 optical pick-up
section
3 two springs
3 two springs
5 screw
(BVTP2.6 × 8)
4 wire (flat type)
(16 core) (CN101)
7 BD board
6 Removal
the four solders.
limit switch
(S101)
OPTICAL PICK-UP (KSS-213D / Q-NP) , SLED MOTOR (M102) , SPINDLE MOTOR (M101)
6 spindle motor
(M101)
4 two screws
(P2 × 3)
2 sled shaft
5 sled motor
(M102)
1 claw
– 13 –
Downloaded from www.Manualslib.com manuals search engine
AUDIO BOARD, CAPSTAN MOTOR (M1)
1 connector
(CN651)
2 four screws
A
(BTP2.6 × 4)
5 two screws
(BTP2.6 × 8)
6 claw
– 14 –
Downloaded from www.Manualslib.com manuals search engine
SECTION 4
TEST MODE
[MC Cold Reset] [Change-over of AM Tuner Step between 9kHz and 10kHz]
• The cold reset clears all data including preset data stored in the • A step of AM channels can be changed over between 9kHz and
RAM to initial conditions. Execute this mode when returning 10kHz.
the set to the customer. Procedure:
Procedure: 1. Press I /u button to turn the set ON.
1. Press three buttons [SPECTRUM ANALYZER], [ENTER], and 2. Select the function “TUNER”, and press [TUNER/BAND]
[DISC 1] simultaneously. button to select the BAND “AM”.
2. The fluorescent indicator tube becomes blank instantaneously, 3. Press I /u button to turn the set OFF.
and the set is reset. 4. Press [ENTER] and I /u buttons simultaneously, and the dis-
play of fluorescent indicator tube changes to “AM 9k STEP”
[CD Delivery Mode] or “AM 10k STEP”, and thus the channel step is changed over.
• This mode moves the pickup to the position durable to vibra-
tion. Use this mode when returning the set to the customer after [LED and Fluorescent Indicator Tube All Lit, Key Check
repair. Mode]
Procedure: Procedure:
1. Press I /u button to turn the set ON. 1. Press three buttons [SPECTRUM ANALYZER], [ENTER] , and
2. Press [PLAY MODE] button and I /u button simultaneously. [DISC 3] simultaneously.
3. A message “LOCK” is displayed on the fluorescent indicator 2. LEDs and fluorescent indicator tube are all turned on.
tube, and the CD delivery mode is set. Press [DISC 2] button, and the key check mode is activated.
3. In the key check mode, the fluorescent indicator tube displays
[MC Hot Reset] “K 1 J0 V0”. Each time a button is pressed, “K”value in-
• This mode resets the set with the preset data kept stored in the creases. However, once a button is pressed, it is no longer taken
memory. The hot reset mode functions same as if the power into account.
cord is plugged in and out. “J” Value increases like 1, 2, 3 ... if rotating [JOG] knob in
Procedure: “+” direction, or it decreases like 0, 9, 8 ... if rotating in “–”
1. Press three buttons [SPECTRUM ANALYZER], [ENTER], and direction.
[DISC 2] simultaneously. “V” Value increases like 1, 2, 3 ... if rotating [VOLUME] knob
2. The fluorescent indicator tube becomes blank instantaneously, in “+” direction, or it decreases like 0, 9, 8 ... if rotating in
and the set is reset. “–” direction.
4. To exit from this mode, press three buttons in the same man-
[Sled Servo Mode] ner as step 1, or disconnect the power cord.
• This mode can run the CD sled motor freely. Use this mode, for
instance, when cleaning the pickup.
Procedure:
1. Select the function “CD”.
2. Press three buttons [SPECTRUM ANALYZER], [ENTER], and
[FUNCTION] simultaneously.
3. The Sled Servo mode is selected, if “CD” is blanking on the
fluorescent indicator tube.
4. With the CD in stop status, press ) button in CD section
to move the pickup to outside track, or 0 button to inside
track.
5. To exit from this mode, perform as follows:
1) Move the pickup to the most inside track.
2) Press three buttons in the same manner as step 2.
Note:
• Always move the pickup to most inside track when exiting from this
mode. Otherwise, a disc will not be unloaded.
• Do not run the sled motor excessively, otherwise the gear can be chipped.
– 15 –
Downloaded from www.Manualslib.com manuals search engine
[Aging Mode] 2-2. Operation during Aging Mode
This mode can be used for operation check of CD section and tape In the aging mode, the program is executed in the following se-
deck section. quence.
• If an error occurred: 1. A tape on FWD side is played for one minute.
The aging operation stops. 2. PAUSE STOP is made.
• If no error occurs: 3. Recording is made for 3 minutes. (For the deck not having
The aging operation continues repeatedly. the record function, the play is executed.)
4. FF is executed up to the end of tape.
1. Aging Mode in CD Section 5. A tape is reversed, and the tape on REV side is played for
1-1. Operating Method of Aging Mode one minute.
1. Set discs in DISC 1 and DISC 3 trays. 6. PAUSE STOP is made.
2. Select the function “CD”. 7. Recording is made for 3 minutes. (For the deck not hav-
3. Press three buttons [SPECTRUM ANALYZER] , [ENTER], ing the record function, the play is executed.)
and [KARAOKE PON/MPX] simultaneously. 8. FF is executed up to the end of tape.
4. The aging mode is activated, if a roulette mark on the fluo- 9. Steps 1 through 8 are executed for the other deck.
rescent indicator tube is blinking. 10. Steps 1 through 9 are repeated unless an alarm occurred.
5. In the aging mode, the aging is executed in a sequence
given in “1-2. Operation during Aging Mode”. 2-3. Deck Selection Sequence
The aging continues unless an alarm occurred. • During the aging mode, decks are selected in the following se-
6. To exit from the aging mode, press I /u button to turn the quence:
set OFF. Deck A (FWD) → Deck A (REV)
• If a button other than buttons In CD section is pressed during ↑ ↓
aging, the aging in the CD section is finished. Deck B (REV) ← Deck B (FWD)
• To execute aging to the tape deck section successively, press
· button in the deck A.
“AGING” is displayed on the fluorescent indicator tube. (For
the aging in tape deck, see “2. Aging Mode in Tape Deck Sec-
tion”.
– 16 –
Downloaded from www.Manualslib.com manuals search engine
SECTION 5 SECTION 6
MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS
PRECAUTION TAPE DECK SECTION 0 dB=0.775 V
1. Clean the following parts with a denatured-alcohol-moistened
swab: 1. Demagnetize the record/playback head with a head demagne-
record/playback heads pinch rollers tizer. (Do not bring the head demagnetizer close to the erase
erase head rubber belts head.)
capstan idlers 2. Do not use a magnetized screwdriver for the adjustments.
2. Demagnetize the record/playback head with a head demagne- 3. After the adjustments, apply suitable locking compound to the
tizer. parts adjust.
3. Do not use a magnetized screwdriver for the adjustments. 4. The adjustments should be performed with the rated power
4. After the adjustments, apply suitable locking compound to the supply voltage unless otherwise noted.
parts adjusted. 5. The adjustments should be performed in the order given in
5. The adjustments should be performed with the rated power this service manual. (As a general rule, playback circuit ad-
supply voltage unless otherwise noted. justment should be completed before performing recording
• Torque Measurement circuit adjustment.)
• Tape Tension Measurement 6. The adjustments should be performed for both L-CH and R-
ch.
• Torque Measurement 7. Switches and controls should be set as follows unless other-
wise specified.
Mode Torque Meter Meter Reading
8. Set to test mode. (Press key switch same time
36 to 61g•cm [SPECTRUM ANALYZER] [ENTER] and [EFFECT] but-
Forward CQ-102C
(0.50 – 0.84 oz•inch) ton.)
Forward 2 to 6g•cm
CQ-102C
Back Tension (0.026 – 0.082 oz•inch) • Test Tape
36 to 61g•cm Tape Signal Used for
Reverse CQ-102RC
(0.50 – 0.84 oz•inch) P-4-A100 10 kHz, –10 dB Azimuth Adjustment
Reverse 2 to 6g•cm WS-48B 3 kHz, 0 dB Tape Speed Adjustment
CQ-102RC
Back Tension (0.026 – 0.082 oz•inch) P-4-L300 315 Hz, 0 dB Level Adjustment
61 to 143g•cm
FF, REW CQ-201B
(0.85 – 1.98 oz•inch) Record/ Playback Head Azimuth Adjustment
set
+
–
main board
CN207
Pin 2
– 17 –
Downloaded from www.Manualslib.com manuals search engine
1. Mode: Playback (FWD) Tape Speed Adjustment DECK A
2. Turn the adjustment screw and check output peaks. If the peaks Note: Start the Tape Speed adjustment as below after setting to the test
do not match for L-CH and R-CH, turn the adjustment screw mode.
so that outputs match within 1dB of peak. In the test mode, the tape speed is high during pressing the
[H. SPEED DUBB] button.
Procedure:
1. Turn the power switch on.
within
2. Press the [SPECTRUM ANALYZER] button, [ENTER] but-
1dB ton and [EFFECT] button simultaneously.
L-CH
peak within To exit from the test mode, press the I /u button.
output 1dB Mode: Playback (FWD)
level
test tape
WS-48B frequency counter
R-CH (3 kHz, 0 dB)
peak
Screw Screw
position set +
L-CH R-CH position
–
peak peak
MAIN board
3. Mode: Playback (FWD) CN207 (Pin 3 : L-CH)
(Pin 1 :R-CH)
test tape
P-4-A100 1. Insert the WS-48B into the deck A and the blank tape into the
(10 kHz, –10 dB) oscilloscope
pin 3 deck B.
L-CH
pin 2 2. Press the [REC] button and · button on the deck B. Then
main L the deck B is at recording mode.
board V H
CN207 3. Set the deck A to playback mode.
set R 4. Keep pressing the [H. SPEED DUBB] button in playback mode.
Then at HIGH speed mode.
R-CH
5. Adjust RV652 on the AUDIO board do that frequency counter
pin 1
reads 6,000 ± 60 Hz.
waveform of oscilloscope 6. Take off the [H. SPEED DUBB] button.
Then at NORMAL speed mode.
7. Adjust RV651 on the AUDIO board so that frequency counter
in phase 45 ° 90 ° 135 ° 180 ° reads 3,000 ± 20 Hz.
8. Frequency difference between deck A and deck B the begin-
good wrong
ning of the tape should be within ± 1.5%.
Adjustment Location: AUDIO and MAIN boards
4. Repeat steps 1 to 3 in playback (REV) mode.
5. After the adjustments, apply suitable locking compound to the Sample Value of Wow and flutter: 0.29% or less W. RMS
pats adjusted. (WS-48B)
Adjustment Location: Record/Playback Head (Deck A and B)
and MAIN board. Playback level Adjustment DECK A DECK B
Procedure:
Mode: Playback (FWD)
test tape
P-4-L300 level meter
(315 Hz, 0 dB)
set +
–
– 18 –
Downloaded from www.Manualslib.com manuals search engine
Record bias Current Adjustment DECK B Adjustment Location:
Procedure:
1. Mode: Record [MAIN BOARD] (Component Side)
Pin 6 (L-CH) of IC1501 on the MAIN board. RV1501
Pin #¶ (R-CH) of IC1501 on the MAIN board. CN207
1) 315 Hz 1 3 IC1501
2) 10 kHz 50 mV (–23.8 dB) CN205
AF OSC blank tape RV1551
600 Ω CN-123
attenuator
RECORD
set LEVEL
set +
–
[AUDIO BOARD] (Conductor Side)
CN207 (Pin 3 : L-CH) TAPE SPEED
(Pin 1 : R-CH) RECORD
BIAS CURRENT (NORMAL) (HIGH)
Confirm playback the signal recorded in step 1 become adjustable R L
RV651 RV652
limits as follows. RV301
RV341
If these levels do not adjustable limits, adjustment the RV341 (L- L
RV441 RV311 L
CH) and RV441 (R-CH) on the AUDIO board to repeat steps 1 PB
and 2. R PB LEVEL LEVEL RV411 R
Adjustable limits: Playback output of 315 Hz to playback output RV401
– DECK B – – DECK A –
of 10 kHz: 0 ± 0.5 dB
Adjustment Location: AUDIO and MAIN boards
Record Level Adjustment DECK B * As the adjustment parts is mounted on the component side, ad-
Procedure: just it through a hole in the AUDIO board form conductor side.
1. Mode: Record (Except RV431, 441)
2. Mode: Playback
recorded level meter
portion
set +
–
– 19 –
Downloaded from www.Manualslib.com manuals search engine
CD SECTION S Curve Check
Note: oscilloscope
1. CD Block is basically designed to operate without adjustment. There- BD board
fore, check each item in order given.
2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated. TP (FEO) +
3. Use an oscilloscope with more than 10M impedance. TP (VC) –
4. Clean the object lens by an applicator with neutral detergent when the
signal level is low than specified value with the following checks.
Procedure:
Focus Bias check 1. Connect oscilloscope to test point TP (FEO).
2. Connect between test point TP (FOK) and GND by lead wire.
oscilloscope 3. Turn Power switch on.
4. Put disc (YEDS-18) in and turned Power switch on again and
BD board
actuate the focus search. (actuate the focus search when disc
TP (FEO) + table is moving in and out.)
TP (VC) – 5. Check the oscilloscope waveform (S-curve) is symmetrical
between A and B. And confirm peak to peak level within
Procedure: 3 ± 1 Vp-p.
1. Connect oscilloscope to test point TP (RF). (GND terminal: S-curve waveform
VC)
symmetry
2. Turned Power switch on.
3. Put disc (YEDS-18) in and playback.
4. Confirm that the shape “≈” can be clearly distinguished at the A
center of the waveform and check the RF signal level. within 3 ± 1 Vp-p
B
• RF signal
VOLT/DIV: 200 mV 6. After check, remove the lead wire connected in step 2.
TIME/DIV: 500 ns Note: • Try to measure several times to make sure than the ratio of A : B
or B : A is more than 10 : 7.
• Take sweep time as long as possible and light up the brightness to
level: obtain best waveform.
1.3 ± 0.3 Vp-p
RF Level Check
oscilloscope
BD board
TP (RF) +
TP (VC) –
Procedure:
1. Connect oscilloscope to test point TP (TEO) on BD board.
2. Turned Power switch on.
3. Put disc (YEDS-18) in to play the number five track.
4. Confirm that oscilloscope waveform is clear and check RF
signal level is correct or not.
• SF signal
VOLT/DIV: 200 mV
TIME/DIV: 500 ns
level:
1.3 ± 0.3 Vp-p
Note: Clear RF signal waveform means that the shape “≈” can be clearly
distinguished at the center of the waveform.
– 20 –
Downloaded from www.Manualslib.com manuals search engine
E-F Balance (1 Track Jump) check Adjustment Location:
(Without remote commander)
[BD BOARD] (Conductor Side)
oscilloscope
BD board RF
VC
TP (TEO) + FOK
TP (VC) –
CNU101
IC101 IC
Procedure: I02
1. Connect oscilloscope to test point TP (TEO) on BD board.
2. Turned Power switch on.
3. Put disc (YEDS-18) in to play the number five track. TEO
4. Press the “P (Pause)” button. (Becomes the 1 track jump FEO
GND
mode)
5. Check the level B of the oscilloscope’s waveform and the A
(DC voltage) of the center of the Traverse waveform.
Confirm the following: IC103
A–B
× 100 = ±7 (%)
2 (A + B)
A (DC voltage)
0V
symmetry
level : 500 mV ± 100 mVp-p
– 21 –
Downloaded from www.Manualslib.com manuals search engine
SECTION 7
DIAGRAMS
7-1. IC PIN FUNCTION DESCRIPTION
• MAIN BOARD IC301 µPD780018YGF-028-3BA (SYSTEM CONTROLLER)
Pin No. Pin Name I/O Function
1 TA-MUTE O Line muting on/off control signal output terminal “L”: muting on
DBFB normal/high selection signal output to the M62427FP (IC201)
2 DBFB-H/L O
“L”: DBFB high, “H”: DBFB low
3 427-LAT O Serial data latch pulse output to the M62427FP (IC201)
4 K-CON-LAT O Serial data latch pulse output terminal Not used (open)
5 K-CON-ON O On/off selection signal output of the key control circuit “L”: on Not used (open)
6 F-RELAY O Relay drive signal output for the speaker protect “H”: on
7 R-RELAY O Relay drive signal output for the speaker protect “H”: on Not used (open)
8 PL-RELAY O Relay drive signal output for the speaker protect “H”: on Not used (open)
9 TEST I Test terminal Connected to ground
10 X2 O Main system clock output terminal (5 MHz)
11 X1 I Main system clock input terminal (5 MHz)
12 VDD — Power supply terminal (+5V)
13 XT2 O Sub system clock output terminal (32.768 kHz)
14 XT1 I Sub system clock input terminal (32.768 kHz)
System reset signal input from the reset signal generator (IC302) “L”: reset
15 RESET I
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
16 (INT/IN) I Connected to ground
17 (INT/IN/OUT) I Connected to ground
18 SCOR I Subcode sync (S0+S1) detection signal input from the CXD2519Q (IC103)
19 SOFT-TEST O Output terminal for the software test (open)
20 AC-CUT I AC off detection signal input from the reset signal generator (IC302)
21 RDS-INT I Serial data reading clock signal input for the radio data system Not used (fixed at “L”)
22 RDS-DATA I Serial data input for the radio data system Not used (open)
23 VDD — Power supply terminal (+5V)
24 AVDD — Power supply terminal (+5V) (for A/D conversion)
25 ADJ I Setting terminal for the CD test mode Normally: fixed at “H”
26 A-SHUT I Shut off detection signal input from the deck-A side reel pulse detector (Q1001)
27 B-SHUT I Shut off detection signal input from the deck-B side reel pulse detector (Q1002)
28 B-HALF I Detection input from the deck-B half detect switch (S1006)
29 CLK-CHECK I Not used (fixed at “L”)
30 SPEC-IN I Setting terminal for the version
31 ADJ2 I Setting terminal for the CD test mode Normally: “L”
32 DEMO-MODE I Setting terminal for the demonstration H/L Fixed at “L”
33 AVSS — Ground terminal (for A/D conversion)
34 SQ-DATA-IN I Sub-code Q data input from the CXD2519Q (IC103)
35 NCO O Not used (open)
36 SQ-CLK O Sub-code Q data reading clock signal output to the CXD2519Q (IC103)
37 SW-ON/OFF O Super woofer speaker on/off control signal output terminal Not used (open)
38 FUNC1 I Setting terminal for the function 1 Fixed at “L”
39 FUNC2 I Setting terminal for the function 2 Fixed at “L”
40 VSS — Ground terminal
41 VOL-LAT O Serial data latch pulse output terminal Not used (open)
42 PL-LAT O Serial data latch pulse output terminal Not used (open)
43 COM-DIN I Serial data input terminal Not used (fixed at “L”)
– 22 –
Downloaded from www.Manualslib.com manuals search engine
Pin No. Pin Name I/O Function
44 COM-DOUT O Serial data output to the M62427FP (IC201)
45 COM-CLK O Serial data transfer clock signal output to the M62427FP (IC201)
Power on/off control signal output for the CD mechanism deck section
46 CD-POWER O
“H”: power on, “L”: standby
47 CD-DATA O Serial data output to the CXD2519Q (IC103)
48 CD-CLK O Serial data transfer clock signal output to the CXD2519Q (IC103)
49 MSM-CND O Command data output terminal Not used (open)
50 MSM-BUSY I Busy signal input terminal “L”: busy status Not used (fixed at “L”)
51 MSM-LAT O Serial data latch pulse output terminal Not used (open)
52 MSM-NAR O NAR signal output terminal Not used (open)
53 MSM-CH O Channel select signal output terminal Not used (open)
INPUT- Attenuate control (–5 dB) signal output for the input gain control
54 O
CHANGE “L”: VIDEO, “H”: MD
55 IIC-DATA I/O Communication data bus with the fluorescent indicator tube driver (IC601)
Communication data reading clock signal input or transfer clock signal output with the fluo-
56 IIC-CLK I/O
rescent indicator tube driver (IC601)
Reset signal output to the CXA1992AR (IC101), BA5941FP (IC102) and CXD2519Q (IC103) on
57 XRST O
the CD mechanism deck section “L”: reset
58 XLT O Serial data latch pulse output to the CXD2519Q (IC103)
59 WDCL O Word clock signal output terminal Not used (open)
60 TBL-L O Motor drive signal output to the disc tray turn motor driver (IC201) *1
61 TBL-R O Motor drive signal output to the disc tray turn motor driver (IC201) *1
62 TRAY-LED O LED drive signal output for the CD tray LED indicate “H”: LED on
63 LOAD-OUT O Motor drive signal output terminal Not used (open)
64 LOAD-IN O Motor drive signal output terminal Not used (open)
65 ST-CLK O PLL serial data transfer clock signal output to the FM/AM tuner unit
66 ST-DIN I PLL serial data input from the FM/AM tuner unit
67 ST-DOUT O PLL serial data output to the FM/AM tuner unit
68 ST-CE O PLL chip enable signal output to the FM/AM tuner unit
69 TUNED I Tuning detection signal input from the FM/AM tuner unit “L”: tuned
70 STEREO I FM stereo detection signal input from the FM/AM tuner unit “L”: stereo
71 VSS — Ground terminal
72 ST-MUTE O Tuner muting control signal output to the FM/AM tuner unit “L”: muting on
73 SENS2 I Internal status (SENSE) signal input from the CXA1992AR (IC101)
74 SENS I Internal status (SENSE) signal input from the CXD2519Q (IC103)
75 DISC-SENS I Disc status detection signal input terminal Not used (open)
76 T-SENS I Disc tray status detection signal input from the disc tray sensor (IC202)
77 UP SW I Detection input from the UP switch (S201)
78 ENC3 I
79 ENC2 I Rotary encoder pulse input for the disc tray address detect Not used (open)
80 ENC1 I
81 OUT-OPEN I Disc tray open/close detect switch input terminal “L”: open, “H”: close Not used (open)
High/normal speed selection signal output of the capstan motor (M1)
82 CAP-H/N O
“L”: high speed, “H”: normal speed
83 A-TRG O Motor drive signal output to the trigger motor driver (IC1502)
84 B-TRG O Motor drive signal output to the trigger motor driver (IC1502)
85 TRG-LOW O Motor control signal output to the trigger motor driver (IC1502)
– 23 –
Downloaded from www.Manualslib.com manuals search engine
Pin No. Pin Name I/O Function
86 CAP-M-ON/OFF O Capstan motor (M1) on/off control signal output terminal “L”: capstan motor on
87 PB-A/B O Deck-A/B selection signal output to the HA12203NT (IC1501) “L”: deck-A, “H”: deck-B
Normal/high speed selection signal output to the HA12203NT (IC1501)
88 EQ-H/N O
“L”: normal speed, “H”: high speed
Recording bias on/off selection signal output to the HA12203NT (IC1501)
89 BIAS O
“L”: bias off, “H”: bias on
Recording muting on/off selection signal output to the HA12203NT (IC1501)
90 REC-MUTE O
“L”: muting on, “H”: muting off
Dolby NR on/off selection signal output to the HA12203NT (IC1501)
91 NR-ON/OFF O
“L”: dolby off, “H”: dolby on
Recording/playback/pass selection signal output to the HA12203NT (IC1501)
92 R/P-PASS O
“L”: recording mode
Line muting on/off selection signal output to the HA12203NT (IC1501)
93 TC-MUTE O
“L”: muting off, “H”: muting on
94 A-PLAY-SW I Detection input from the deck- A play detect switch (S1001) “H”: deck-A play
95 B-PLAY-SW I Detection input from the deck- B play detect switch (S1002) “H”: deck-B play
Recording/playback select signal output to the REC/PB switch (IC602)
96 RELAY O
“L”: playback, “H”: recording
Detection input from the deck-A cassette detect switch (S1003)
97 A-HALF I
“L”: cassette in, “H”: no cassette
Power on/off control signal output for the audio system (+5V) and deck, panel, audio system
98 POWER O
(+7V and –7V) “L”: power on, “H”: standby
99 SW-F-CON O Super woofer mode control signal output to the M62427FP (IC201) “H”: music, “L”: movie
100 STK-MUTE O Power amplifier on/off selection signal output terminal “L”: on, “H”: standby
– 24 –
Downloaded from www.Manualslib.com manuals search engine
• PANEL BOARD IC601 TMP87CH75F-6659
(FLUORESCENT INDICATOR TUBE DRIVE, LED DRIVE, KEY CONTROL)
Pin No. Pin Name I/O Function Pin No. Pin Name I/O Function
1 SEG-35 O Segment drive signal output to the fluorescent indicator tube (FL601) Key input terminal (A/D input) (S641 to 647, 661 to 666)
2 V-LOAD — Power supply terminal (–30V) (for fluorescent indicator tube drive) 37 KEY-5 I DECK A ·/ª/p/0/), DOLBY NR, DIRECTION, DIRECT PLAY DISC 1/2/3/4/5, DJ
3 LED1 O MIX FLASH keys input
LED drive signal output terminal (TUNER/BAND)
4 LED2 O LED drive signal output terminal (ENTER/NEXT, GROOVE) 38 DOOR SW I CD door switch (S691 (6 OPEN)) input terminal
5 LED3 O LED drive signal output terminal (SUPER WOOFER, CD P) 39 SIRCS I Remote control signal input from the remote control receiver (IC602)
6 LED4 O LED drive signal output terminal (CD ·) 40 VOL-B I Rotary encoder pulse input from the S701 (VOLUME)
7 LED5 O LED drive signal output terminal (DECK B ª) 41 JOG-B I Jog dial pulse input from the S711 (≠ AMS ± jog dial)
8 LED6 O LED drive signal output terminal (DECK B ·) 42 SPEANA-1 I Spectrum analyzer drive (for low frequency) signal input terminal
9 LED7 O LED drive signal output terminal (TAPE P, r REC) 43 SPEANA-2 I Spectrum analyzer drive (for low and middle frequency) signal input terminal
10 LED8 O LED drive signal output terminal (EFFECT, ENTER) 44 SPEANA-3 I Spectrum analyzer drive (for middle and high frequency) signal input terminal
11 VSS — Ground terminal 45 SPEANA-4 I Spectrum analyzer drive (for high frequency) signal input terminal
12 X-OUT O System clock output terminal (8 MHz) 46 L+R I Spectrum analyzer drive (for VACS, non-stop signal) signal input terminal
13 X-IN I System clock input terminal (8 MHz) 47 LED18 O LED drive signal output terminal (NON-STOP)
System reset signal input from the reset signal generator (IC302) “L”: reset 48 VASS — Ground terminal
14 RESET I
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H” 49 VAREF I Reference voltage (+5V) input terminal (for A/D conversion)
15 LED9 O LED drive signal output terminal (FILE 1, FILE 2) 50 VDD — Power supply terminal (+5V)
16 LED10 O LED drive signal output terminal (FILE 3, FILE 4) 51 to 66 GR-1 to GR-16 O Grid drive signal output to the fluorescent indicator tube (FL601)
17 TEST I Connected to ground 67 to 100 SEG-1 to SEG-34 O Segment drive signal output to the fluorescent indicator tube (FL601)
18 LED11 O LED drive signal output terminal (FILE 5, P FILE)
19 LED12 O LED drive signal output terminal (OTHERS, MUSIC)
20 LED13 O LED drive signal output terminal Not used (open)
21 LED14 O LED drive signal output terminal Not used (open)
22 LED15 O LED drive signal output terminal (DECK A ·)
23 LED16 O LED drive signal output terminal (DECK A ª)
24 VOL-A I Rotary encoder pulse input from the S701 (VOLUME)
25 LED17 O LED drive signal output terminal Not used in this set
26 JOG-A I Jog dial pulse input from the S711 (≠ AMS ± jog dial)
Communication data reading clock signal input or transfer clock signal output with the system
27 CLOCK I/O
controller (IC301)
28 DATA I/O Communication data bus with the system controller (IC301)
29 LED SELECT O LED selection signal output terminal
30 VDD — Power supply terminal (+5V)
31 VSS — Ground terminal
32 MODEL I Destination setting terminal
Key input terminal (A/D input) (S601 to 607, 609 to 616)
ENTER/NEXT, TUNER MEMORY, TUNING MODE, TUNER/BAND, TUNING +/–,
33 KEY-1 I
STEREO/MONO, FUNCTION, GROOVE, GEQ 4/9/(/$, SUPER WOOFER, SUPER W
MODE keys input
Key input terminal (A/D input) (S619, 620, 676 to 679, 681 to 686)
35 KEY-3 I GEQ CONTROL, ENTER, CD ·/p/P, DISC SKIP, CD ), REPEAT, PLAY MODE,
1/ALL DISCS, EDIT, CD 0 keys input
Key input terminal (A/D input) (S627 to 634, 667, 668)
36 KEY-4 I SPECTRUM ANALYZER, DISPLAY/DEMO, POWER, t/CLOCK SET, REC, DAILY 1/2,
SLEEP, NON-STOP, DJ MIX LOOP keys input
– 25 – – 26 –
FILI
SERIAL
PCO
FILO
CLTV
4 38 BCK BCKI SAMPLING
54 55 INPUT
LRCK LRCKI INTERFACE DIGITAL
INTERFACE
DETECTOR RF 50 51
RFO RF ASYMMETRY EFM FILTER
INTERNAL BUS
+ SUMMING 33 44 DIGITAL PLL C2PO
D/A
PD2 I-V AMP CORRECTION DEMODULATOR 63
A D AMP RFCK
PD2 RFI 62 NOISE
5 39 32 ASYI WDCK
46 49 SHAPER
ASYO
47
EMPHI
1
I-V AMP
B C PWM &
FOCUS OK FOK FOK INTEGRATOR
2 27 23 73
COMPARATOR
AOUT1
AOUT2
FOCUS OK SUB-CODE
AMP PROCESSOR
F
XLT XLTO
SERVO 21 16 61
DEFECT IIL LOCK WFCK
IC101 (1/2) IIL 19 74
AMP XRST GTOP 85 94
23 58
AIN1
AIN2
SENS1 SEIN
IIL 25 13 TIMING CLOCK
C.OUT CNIN DIGITAL CLV CPU INTERFACE
24 14 LOGIC GENERATOR
SENS2 BUFFER
TTL 26
CKOUT
LOUT2
LOUT1
SQSO
SPOD
SCOR
XTAO
SQCK
SBSO
LOCK
XROF
SENS
CLOK
DATA
XRST
EXCK
XLAT
MON
MDS
MDP
XTAI
C4M
OPTICAL PICK-UP
(KSS-213D/Q-NP) FOCUS FEO FEI FEO
1 FOCUS PHASE
ERROR 2 6
COMPENSATION 100 26 27 28 29 64 8 7 9 10 12 11 75 76 77 21 6 89 90 70 86 93
AMP
FE BIAS
40 X101 R-CH
+5V 16.9344MHz
F TRACKING TEO S101
CD-L
41 I-V TEI TRACKING PHASE TAO
E ERROR 45 47 13 (LIMIT)
42 AMP COMPENSATION
AMP SYSTEM CONTROLLER ON : When the optical pick-up
LASER DIODE IC301 (1/3) is inner position.
57 A
XRST (Page 31)
AUTOMATIC LD LD PD
POWER CONTROL 36
AMP AMP
Q101 PD
PD LD SQ-DATA-IN 34
37 OPTICAL
SQ-CLK 36
TRANSCEIVER
SENS 74 IC391
73 SENS2 CD-DATA 47
CD-CLK 48 IC391
XLT 58 CD DIGITAL
SCOR 18 OUT
OPTICAL
S201
(UP)
9 UPSW 77
MUTE
2-AXIS
DEVICE OUT4A
16 TRACKING IN4A DISC TRAY SENSOR
(TRACKING)
OUT4B 27 T-SENS 76
15 COIL DRIVE IC202
(FOCUS)
OP OP+,
OUT3A
22, 23
IN1 OUT1
FOCUS/TRACKING COIL DRIVE, TBL-L 60 9 MOTOR 7 M201
SPINDLE/SLED MOTOR DRIVE TBL-R 61 1
IN2
DRIVE
OUT2
3
M (DISC TRAY TURN)
05 IC102
SLED SERVO
OUT1A IC101 (2/2) LED DRIVE D201
M101 13 SPINDLE IN1B TRAY-LED 62
(SPINDLE) M 14
OUT1B
MOTOR DRIVE
3 Q201 (DISC No.) • SIGNAL PATH
: CD PLAY
: DIGITAL OUT
– 27 – – 28 –
DECK PROCESS
DECK A/B SELECT, PB/REC EQ AMP,
DOLBY NR AMP • SIGNAL PATH
IC1501
: PLAYBACK (DECK A)
HP101 DOLBY PASS
(PLAYBACK) : PLAYBACK (DECK B)
70 PB OUT (L) PB-L
PB EQ AMP
L-CH 2
AIN (L)
DOLBY NR
8 B
(DECK A)
AMP
: RECORD
IC611 BIN (L) (Page 31)
4 120 CIRCUIT
RV311
PB LEVEL (L) R-CH +
R-CH R-CH (DECK A)
EQ OUT
L.P.F. (L)
EQ IN (L)
EQ AMP
RIN (L)
NORM BUFFER
25 BIAS
CROM
24 CONTROL MAOUT
HRPE101 (1/2) METAL CIRCUIT
23 28 6 9 10
(RECORD/PLAYBACK)
PB EQ AMP
(DECK B)
L-CH IC601 27
MSIN
REC/PB/PASS
BIAS-ON/OFF
NORM/HIGH
RV301
RM-ON/OFF
LM-ON/OFF
NR-ON/OFF
RV1501
A 120/70
B 120/70
REC/PB SWITCHING
IC602 S1004
3 1 (DECK A 120/70)
R-CH R-CH
S1008
(DECK B 120/70)
4
PB-A/B
EQ-H/N
BIAS
REC-MUTE
NR-ON/OFF
R/P-PASS
TC-MUTE
A-SHUT
B-SHUT
CAP-H/N
CAP-M-ON/OFF
BIAS OSC
Q621, 622
SYSTEM CONTROLLER
A-PLAY-SW
B-PLAY-SW
IC301 (2/3)
TRG-LOW
A-HALF
B-HALF
A-TRG
B-TRG
94 95 97 28 85 84 83
S1009 VZ
(DECK B REC) 4
D+5V
TRIGGER
MOTOR CONTROL
Q1534, 1535
– 29 – – 30 –
J761
MIX MIC
(Page 30) • SIGNAL PATH
MIC AMP MIC AMP REC-L
IC760 (1/2) IC760 (2/2) C : CD PLAY
RV760 : TAPE PLAY
L J101 (2/2)
MIC LEVEL
VIDEO/MD : RECORD
(AUDIO) OUT
R-CH R-CH R
: TUNER (FM/AM)
J101 (1/2)
: MIC INPUT
PHONO EQ
L AMP
IC101 62 61
PHONO IN
REC REC
R R-CH FUNCTION SWITCH 2A 2B
IC102
IN-2B KEY KEY GRAPHIC VOL VOL BB BUF
L 12 69 IN2 OUT2 F OUT2 IN2 VOLUME OUT2 IN2 BASS BOOST OUT2 L-CH
INPUT EQUALIZER
VIDEO/MD
14 IN-2A SELECT SOUND
65 + 64
CONTROL
45 44
CONTROL
43 42 CONTROL 38 G
(AUDIO) IN 13 71 CIRCUIT
R R-CH 15 CONTROL CIRCUIT (Page 33)
11 CIRCUIT MUTING
ATTENUATOR Q204
(–5dB) R-CH R-CH
INH A B
Q101 INPUT SELECT SWITCH,
6 10 9 R-CH
R-CH GRAPHIC EQUALIZER CONTROL,
CPU INTERFACE COMMAND ELECTRICAL VOLUME
IC201
BUF IN2
PORT-C
PORT-B
PORT-A
CLOCK
LATCH
BB12,
DATA
BB22
CD-L
(Page 28) A
29 28 30 33 32 34 39 41, 40
PB-L
FEED BACK
(Page 30) B SWITCH
Q203
D291
FEED BACK
R-CH + H
(Page 33)
ST-CE
RESET
E
(Page 35)
RESET
DATA
X302
CLK
X301 SWITCH
5MHz 32.768kHz Q301
68 65 66 67 69 70 72 54 44 45 3 10 11 13 14 46 98 55 56 99 2 1 20 15
ST-MUTE
XT1
CD-POWER
POWER
SW-F-CON
DBFB-H/L
427-LAT
ST-DIN
ST-DOUT
TUNED
XT2
IIC-DATA
TA-MUTE
AC-CUT
INPUT-CHANGE
COM-DOUT
X2
X1
ST-CE
ST-CLK
STEREO
IIC-CLK
RESET
COM-CLK
STK-MUTE
F-RELAY
SYSTEM CONTROLLER
IC301 (3/3)
05
100 6
(Page 34)
RELAY
J
STK-MUTE
I
(Page 33)
– 31 – – 32 –
J760
PHONES
• SIGNAL PATH
: CD PLAY
+ R
17
POWER AMP 13 L-CH (–) -1 –
D192
D191
IC801 (2/2)
6 FAN MOTOR
DRIVE M
FEED BACK OVER LOAD Q191, 192
H + DETECT M100
Q801, 851 (FAN)
(Page 32)
D811
1 10 R-CH (+) -2
R-CH POWER AMP
IC821 (1/2)
17 13 R-CH (–) -2
POWER AMP
IC821 (2/2)
6
OVER LOAD RELAY DRIVE RELAY
DETECT Q141, 142 J
Q821, 871 (Page 32)
RY141 RY142
STANDBY SWITCH
Q283
D831
2
STK-MUTE PROTECTOR
I IC281
OFFSET
(Page 32) DETECT
FLIP VCC ON RELAY
6
FLOP MUTE DRIVE
OVER LOAD OVER LOAD
DETECT SWITCH 1 DETECT
Q282
AC OFF
DETECT
4 7
RELAY SWITCH
Q281 AC OFF
05 M
(Page 36)
– 33 – – 34 –
RESET
E 14 RESET
(Page 32)
D+5V, A+5V B+
CD MECHANISM DECK SWITCH
SECTION B+ Q901, 902
B+
42 SPEANA-1 AUDIO D+5V SWITCH
BAND-PASS 43 SPEANA-2 Q905, 906 D913
FILTER CIRCUIT 44 SPEANA-3
GR-1 – GR-16
38 DOOR SW +7V
+7V
REGULATOR
(CD M+7V) AC OFF
IC902
S601 – 607, 609 – 616, 619 – 625, D+5V
B+ SWITCH M (Page 34)
Q602, 603
S627 – 634, 641 – 647, 651 – 659,
REGULATOR
S661 – 668, 676 – 679, 681 – 686 Q601 CONTROL SWITCH
Q907
KEY-1 – KEY-5
LED SELECT 29
33 – 37
D952
D951
+7V
–30V
X-IN
–30V RECT
REGULATOR
FL DRIVER (IC601) D908, 909
Q904
12 13
Except E, Argentine models
TO VF1
X601 FLUORESCENT INDICATOR TUBE
8MHz (FL601) VF2
05 AC IN
B+ VOLTAGE
POWER AMP RECT
SELECT SWITCH
(IC801, 821) B– D800
S901
S901
VOLTAGE
SELECTOR
E, Argentine models
– 35 – – 36 –
MOTOR board
LEAF SWITCH
board
CD MOTOR board
BD board
AUDIO board
BD LED board
TABLE SENSOR board
– 37 – – 38 –
• Semiconductor
Location
Ref. No. Location
IC101 C-5
IC201 B-5
IC501 C-6
Q101 C-3
MAIN BOARD
CN202
(Page 51)
– 39 – – 40 –
– 41 – – 42–
TABLE SENSOR
BOARD
CD MOTOR
(DISC TRAY TURN) BOARD
BD LED
MAIN BOARD
BOARD CN203
(PAGE 51)
CD MOTOR
BOARD
– 43 – – 44 –
– 45 –
) ( ) (PAGE 51)
MAIN BOARD ( )
MOTOR
CN205
BOARD
( )
AUDIO BOARD
CN651
(DECK B PLAY)
(DECK A PLAY)
(DECK A HALF) (DECK A 120/70) (DECK A REC) (DECK B HALF) (DECK B 120/70) (DECK B REC)
MAIN BOARD
CN206
(PAGE 51)
– 47 – – 48 –
– 49 – – 50 –
IC101 A-11
IC102 B-11
IC201 D-10
IC231 G-7
IC281 H-9
IC301 D-5
IC302 E-5
IC391 A-12
IC901 G-4
IC902 G-5
IC903 F-4
IC904 H-4
IC1501 B-2
IC1502 C-2
Q101 B-11
Q102 B-11
Q103 B-11
Q141 I-10
Q142 H-10
Q151 B-11
Q191 F-12
Q192 E-12
Q201 F-10
Q202 F-10
Q203 F-10
Q204 G-8
Q231 G-8
Q232 G-8
Q251 F-9
Q252 F-8
Q253 F-8
Q254 G-8
Q281 I-9
Q282 H-8
Q283 I-8
Q301 E-6
Q901 G-3
Q902 G-4
Q903 I-3
Q904 I-3
Q905 G-4
Q906 G-4
Q907 H-4
Q1531 C-1
Q1532 C-1
Q1533 C-1
Q1534 C-2
Q1535 C-2
– 51 – – 52 –
The components identified by mark ! or dotted line • Voltages and waveforms are dc with respect to ground
with mark ! are critical for safety. under no-signal (detuned) conditions.
Replace only with part number specified. no mark : FM
[ ] : CD
( ) : VIDEO/MD (AUDIO)
– 55 – 〈〈 〉〉 : PLYABACK – 56 –
– 57 – – 58 –
• Semiconductor
Location
Ref. No. Location
D800 B-2
D801 C-1
D811 C-4
D821 D-4
D831 D-8
D841 C-2
D842 C-2
D851 C-4
D871 C-7
D891 D-4
D892 D-4
IC801 D-2
IC821 D-5
Q801 D-1
Q821 D-4
Q851 D-3
Q871 D-7
– 59 – – 60 –
– 61 – – 62 –
• Semiconductor
Location
Ref. No. Location
D601 D-9
D602 D-10
D603 C-9
D604 B-9
D605 B-10
D606 B-9
D607 C-9
D611 A-1
D612 A-1
D613 B-3
D614 D-3
D615 F-1
D616 E-6
D617 G-7
D618 E-11
D619 E-10
D620 E-10
D621 E-9
D622 E-8
D623 E-7
D624 E-7
D625 E-7
IC601 B-7
IC602 B-10
Q601 B-2
Q602 C-3
Q603 D-2
Q604 A-2
Q605 D-3
Q606 D-3
Q607 D-4
Q608 D-4
Q609 D-4
Q610 D-4
Q611 D-4
Q614 G-4
Q615 G-4
Q617 G-4
Q618 G-4
Q619 G-3
Q621 G-3
Q622 G-3
– 63 – – 64 –
– 65 – – 66 –
– 67 – – 68 –
– 69 – – 70 –
– 71 – – 72 –
– 73 – – 74 –
– 75 – – 76 –
135.5 µs
200 ns
2 IC101 2 (FEI) (PLAY MODE) 7 IC103 &¢ (WFCK) 2 IC301 !¢ (XT1)
135.5 µs
30.4 µs
3 IC101 $¶ (TEI) (PLAY MODE) 8 IC103 *ª (XTAI)
– PANEL Section (1/3) –
1 IC601 !£ (X-IN)
3.6 Vp-p
59.8 ns
4 IC103 @¶ (MDP)
125 ns
2.4 Vp-p
7.8 µs
5 IC103 ^º (XPCK)
7 Vp-p
230 ns
– 77 –
Downloaded from www.Manualslib.com manuals search engine
• IC Block Diagrams
– BD Board –
IC101 CXA1992AR
RF_M
RF_O
RFTC
RF_I
PD2
PD1
CC1
CC2
FOK
PD
LD
CP
CB
39 38 37 36 35 34 33 32 31 30 29 28 27
VEE
–
+
–
+
–
+
–
+
RF SUMMING
PD2 IV PD1 IV –
+
AMP
AMP AMP
–
+
+
–
FE_BIAS 40 26 SENS2
–
+
VCC +
+
–
APC –
VEE IIL
F 41 – ↓ 25 SENS1
+ LASER POWER CONTROL TTL
F IV AMP VCC
–
+
+
–
+
VCC FE AMP VCC
E 42 – 24 C. OUT
–
+
–
+
+
E IV AMP
VEE
–
+
+
–
DFCT
–
+
EI 43 23 XRST
–
+
IFB4
IFB5
IFB2
IFB3
IFB6
IFB1
BAL1
BAL2
BAL3
BAL4
+
VEE
–
+
–
LEVEL S
VEE
TGFL
VEE
VEE 44 VEE 22 DATA
TOG4
TOG3
TOG2
TOG1
FO. BIAS
–
–
+
+
WINDOW VCC
–
+
MIRR IIL
+ COMP. ↓
–
+
– TTL TTL
TEO 45 + TRK. GAIN FOK ↓ 21 XLT
– WINDOW COMP. IIL
+ +
– –
DFCT1
LDON
E-F BALANCE
MIRR
LPCL
TGFL
LPC
CC1
LPFI 46 + WINDOW COMP. 20 CLK
+
– FOH
–
FOL
TGH
TGL IIL DATA REGISTER
TEI 47 INPUT SHIFT REGISTER 19 LOCK
BALH
– ADDRESS DECODER
+ BALL
SENS SELECTOR
ATSC OUTPUT DECODER
TZC
ATSC 48 – FZC VCC 18 VCC
+
ATSC
WINDOW
COMP.
DFCTO IFB1-6 FS1-4 TG1-2 TM1-7 PS1-4
TZC 49 – BAL1-4 ISET 17 ISET
+ TOG1-4
DFCT
TZC COMP.
TM1
VCC VCC
TDFCT 50 TRACKING 16 SL_O
VCC PHASE COMPENSATION
TG1 TM4 TM6
+
VC 51 – 15 SL_M
VCC
TM7
VCC VEE
FOCUS FS1 TM5
PHASE COMPENSATION TM3 –
FZC 52 + + 14 SL_P
–
VEE VEE
+ FS2 TM2
DFCT – Charge
up FSET
FZC COMP.
TG2
–
FS4
+
VEE
1 2 3 4 5 6 7 8 9 10 11 12 13
FEO
FEI
FDFCT
FGD
FLB
FE_O
FE_M
SRCH
TGU
TG2
FSET
TA_M
TA_O
– 78 –
Downloaded from www.Manualslib.com manuals search engine
IC102 BA5941FP-E2
OP IN (–)
OP IN (+)
OP OUT
OUT3A
OUT3B
OUT4A
OUT4B
IN4B
IN4A
IN3B
IN3A
GND
VCC
NC
28 27 26 25 24 23 22 21 20 19 18 17 16 15
NC
– +
Vcc + – + – + – + –
–
+ LEVEL SHIFT
–
+ LEVEL SHIFT
+
LEVEL SHIFT
–
+
LEVEL SHIFT
–
– + + – – + + –
Vcc MUTE Vcc
1 2 3 4 5 6 7 8 9 10 11 12 13 14
VCC
BIAS IN
IN1B
IN1A
IN2B
IN2A
GND
GND
MUTE
VCC
OUT2A
OUT2B
OUT1A
OUT1B
IC103 CXD2591Q
PCMDI
EMPHI
PCMD
LRCKI
SYSM
EMPH
WFCK
MNT0
MNT1
MNT3
SCOR
DOUT
SBSO
GTOP
XROF
C2PO
XPCK
XUGF
EXCK
RFCK
XTSL
FSTT
BCKI
C4M
VDD
VDD
VSS
VSS
BCK
GFS
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51
NC 81 50 LRCK
AVSS 82 49 WDCK
AVDD 83 48 ASYE
AOUT1 84 47 ASYO
– ASYMMETRY
AIN1 85 46 ASYI
– CORRECTOR
PWM
+
3RD-ORDER NOISE SHAPER
LOUT1 86 + 45 BIAS
AVSS 87 44 RF
ERROR
XVDD 88 CORRECTOR 43 AVDD
D/A
XTAI 89 EFM INTERFACE 42 CLTV
DEMODURATOR DIGITAL
XTAO 90 – 41 AVSS
PLL
PWM
XVSS 91 – + 40 FILI
+
AVSS 92 16K RAM DIGITAL OUT 39 FILO
LOUT2 93 38 PCO
AIN2 94 OSC 37 VCTL
AOUT2 95 36 V16M
AVDD 96 35 VCKI
SERIAL-IN OVER SAMPLING SUB CODE
CLOCK
AVSS 97 INTERFACE DIGITAL FILTER PROCESSOR 34 VPCO1
GENERATOR
NC 98 33 VPCO2
NC 99 TIMING SERVO 32 TES1
LOGIC CPU
XRST 100 AUTO DIGITAL CLV 31 TES0
INTERFACE
SEQUENCER
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
VDD
VSS
LMUT
RMUT
TES2
CKOUT
SQCK
SQSO
SENS
DATA
XLAT
CLOK
SEIN
CNIN
DATO
XLTO
CLKO
SPOA
SPOB
SPOC
SPOD
XLON
FOK
VDD
VSS
MON
MDP
MDS
LOCK
PWMI
– 79 –
Downloaded from www.Manualslib.com manuals search engine
– CD MOTOR Board –
IC201 TA8409S
VREF
STANDBY BLOCK
BLOCK
HEAT
CUT OFF
BLOCK
1 2 3 4 5 6 7 8 9
IN2 VCC OUT2 NC GND VS OUT1 VREF IN1
– MAIN Board –
IC281 µPC1237HA IC901 LA5617
COMPARATER
VMUTE VCC VREF
AUTORESET
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8 9 10
VO1
VCC
CN1
EN
EN DISPLAY
GND
NC
CN2
VEE
VO2
– AUDIO Board –
IC1502 LB1641 IC602 µPC1330HA
MOTOR MOTOR
DRIVE DRIVE
COMPARATER
1 2 3 4 5 6 7 8 9
SW R1 GND SW P1 CONT GND VCC SW P2 GND SW R2
FWD/REV/STOP
CONTROL LOGIC
1 2 3 4 5 6 7 8 9 10
FILTER
MOTOR
GND
FILTER
CLAMP
FWD.IN
REV.IN
VCC 1
VCC 2
MOTOR
NOISE
NOISE
DRIVE
DRIVE
– 80 –
Downloaded from www.Manualslib.com manuals search engine
SECTION 8
EXPLODED VIEWS
NOTE:
• -XX and -X mean standardized parts, so they • Items marked “*” are not stocked since they The components identified by
may have some difference from the original are seldom required for routine service. Some mark ! or dotted line with mark
one. delay should be anticipated when ordering ! are critical for safety.
Replace only with part number
• Color Indication of Appearance Parts these items. specified.
Example: • The mechanical parts with no reference num-
KNOB, BALANCE (WHITE) . . . (RED) ber in the exploded views are not supplied.
↑ ↑ • Hardware (# mark) list and accessories and
Parts Color Cabinet's Color packing materials are given in the last of the
• Abbreviation electrical parts list.
AR : Argentine SAF : South African
AUS : Australian MX : Mexican
XB66: AUS
2 #2
4
#2
#1
1 #3
#1
#1
#2
#1
M100
6 5
#1
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 3-363-099-01 SCREW (CASE 3 TP2) * 3 4-996-413-81 PANEL, BACK (XB660)
* 2 4-987-052-92 CASE 4 4-956-370-12 BAND, PLUG FIXED (XB66: AUS)
* 3 4-996-413-01 PANEL, BACK (XB66: E, AR) 5 1-233-545-11 ENCAPSULATED COMPONENT
* 3 4-996-413-21 PANEL, BACK (XB66: MX) (FM/AM TUNER UNIT)
* 3 4-996-413-31 PANEL, BACK (XB66: AUS) 6 1-769-974-11 WIRE (FLAT TYPE) (13 CORE)
M100 1-763-072-11 FAN, D.C.
* 3 4-996-413-41 PANEL, BACK (XB66: SAF)
– 81 –
Downloaded from www.Manualslib.com manuals search engine
(2) FRONT PANEL SECTION-1
58
57 59 72
TCM-220WR2
61
57 57
57 60 62
not
57 supplied
#1
55
77
56 62
78
75
57 76
64 63
54 not 57
65 supplied
57
57 66
78 74
53 69
73 67
supplied
with S711
57
70
52 51 68
71
57
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
51 4-987-995-01 SPRING (CD EJECT), COMPRESSION 65 4-987-000-12 BUTTON (EJECT B)
52 4-987-001-11 BUTTON (EJECT CD) * 66 1-664-013-11 TC-B SW BOARD
* 53 1-664-019-11 CD-A SW BOARD * 67 1-664-020-11 CD-B1 SW BOARD
54 X-4949-282-1 PANEL (A) SUB ASSY 68 X-4949-279-1 BUTTON (CD STOP) ASSY
* 55 1-664-012-11 TC-A SW BOARD 69 4-987-037-11 KNOB (JOG)
– 82 –
Downloaded from www.Manualslib.com manuals search engine
(3) FRONT PANEL SECTION-2
110
109
supplied with
not 109
J761
supplied
supplied with
RV760
supplied with
J760
108
113
109
112
111
114 115
115
115
not
supplied with supplied 109
S701
not
supplied
107
101
106
105
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
101 X-4949-292-1 PANEL ASSY (XB66) * 110 A-4392-452-A HP/MIC BOARD, COMPLETE
101 X-4949-613-1 PANEL ASSY (XB660) 111 4-986-990-11 BUTTON (CURSOR)
105 4-948-236-21 CUSHION (107) 112 4-978-683-01 SPRING, COMPRESSION
106 X-4949-271-1 LID ASSY, CASSETTE * 113 4-987-041-01 COVER, CURSOR
107 4-987-036-11 KNOB (VOL) * 114 A-4403-838-A PANEL BOARD, COMPLETE
108 4-973-644-71 KNOB (MIC) 115 1-773-051-11 WIRE (FLAT TYPE) (17 CORE)
109 4-951-620-01 SCREW (2.6X8), +BVTP 116 4-987-996-01 SPRING (TC LID), TENSION
– 83 –
Downloaded from www.Manualslib.com manuals search engine
(4) CHASSIS SECTION
#13 151
not supplied
#1
not supplied
152
#4
#1
not
supplied
E, MX
CDM37LH-5BD29AL 155
#1
#1 #1
159
SA, AR AR
#1
158
156
159
AUS
not supplied
159
157
not supplied #1
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* 151 1-668-169-11 TRANS BOARD * 155 A-4407-366-A MAIN BOARD, COMPLETE (XB66:AUS, SAF)
152 3-703-244-00 BUSHING (FBS001), CORD 156 1-777-868-11 WIRE (FLAT TYPE) (19 CORE)
(XB66: AUS, SAF, AR) 157 X-4941-228-1 FOOT (F22125H-M)
152 4-966-266-01 BUSHING (S) (FBS002), CORD ! 158 1-569-008-11 ADAPTOR, CONVERSION 2P (XB66: AR)
(XB66: E, MX/XB660) ! 159 1-558-943-51 CORD, POWER (XB66: E, MX/XB660)
* 153 A-4403-848-A POWER AMP BOARD, COMPLETE
* 154 4-988-533-01 HOLDER, PWB ! 159 1-575-651-21 CORD, POWER (XB66: SAF, AR)
! 159 1-696-845-11 CORD, POWER (XB66: AUS)
* 155 A-4403-844-A MAIN BOARD, COMPLETE ! T901 1-431-638-11 TRANSFORMER, POWER
(XB66: E, MX, AR/XB660)
– 84 –
Downloaded from www.Manualslib.com manuals search engine
(5) TAPE MECHANISM DECK SECTION-1
(TCM-220WR2)
208
201
202
209
206
#5
210
#5
#5
207
206
208
203
205
#2
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
201 4-959-229-11 DETENT, CASSETTE 206 3-354-963-01 DAMPER
202 X-4947-943-1 HOLDER (L) ASSY, CASSETTE * 207 4-980-439-01 FULCRUM, HOLDER
203 X-4947-944-1 HOLDER (R) ASSY, CASSETTE 208 3-354-957-01 JOINT (LOCK LEVER)
204 4-959-231-11 SPRING (L), TORSION 209 3-354-953-01 LEVER (LOCK LEVER L)
205 4-959-232-11 SPRING (R), TORSION 210 3-354-954-01 LEVER (LOCK LEVER R)
– 85 –
Downloaded from www.Manualslib.com manuals search engine
(6) TAPE MECHANISM DECK SECTION-2
(TCM-220WR2)
#6 270
including rC
rC refer to next page.
273 269
rA
#6
265 271
264
not supplied
HP101 272
(including rA) 266
262 rB
rA
257
263 269
256 261 265
258 264
272
267
rB
not supplied 266 269
260
255 259
not supplied
268 262
254 HRPE101 257
(including rB)
263
not supplied
253 259 261
256
not supplied
255
252 #7 258
251 260
not supplied #7
254 253
252 not supplied
251
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
251 3-908-560-01 SPRING, AZIMUTH ADJUSTMENT 263 X-3369-908-1 PINCH LEVER (FWD) ASSY
252 3-919-684-01 SCREW, AZIMUTH ADJUSTMENT 264 3-908-613-01 GEAR (S), REEL
253 X-3373-113-1 SLIDER (HEAD) ASSY 265 3-917-141-01 SPRING, COMPRESSION
254 3-908-556-01 SPRING, HEAD TOGGLE 266 X-3371-305-1 REEL (T) ASSY
255 3-908-558-02 FITTING BLOCK, HEAD 267 3-669-465-01 WASHER (1.5), STOPPER
– 86 –
Downloaded from www.Manualslib.com manuals search engine
(7) TAPE MECHANISM DECK SECTION-3
(TCM-220WR2)
rC: MOTOR board (supplied with AUDIO board)
rC M2
(refer to front page.)
318
319
#10
#11
317 310
320 321
#10
302
311
321
309 316 310
#7
325
313
315
308 306
307 319
323
305
312
322 314 307 304
#8
313
303
#9
301
#9
302
not supplied
M1
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
301 3-908-597-01 CAM (A) 315 3-908-600-01 LEVER (REV-B)
302 3-908-608-11 SCREW, STEP * 316 1-650-669-11 LEAF SWITCH BOARD
303 X-3372-930-1 ARM (A) ASSY, FR 317 3-908-598-01 CAM (B)
304 X-3370-882-1 FLYWHEEL (AR) ASSY 318 X-3372-931-1 ARM (B) ASSY, FR
305 3-928-047-01 PULLEY, TENSION 319 3-914-111-01 SPRING (FR), TORSION
– 87 –
Downloaded from www.Manualslib.com manuals search engine
(8) CD MECHANISM DECK SECTION
(CDM37LH-5BD29AL)
351
351
355
352 351
358
356
#1
353
not supplied
354 359
#1
360 357
361
360
359 359
360
373 375
362
372
374
352 368
M201
368
376
368 BU-5BD29AL
367 369
not 369
supplied
363 #1
365
361
#1 370
#1 366
#1 364
371
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
351 4-987-976-01 SCREW, STEP 365 4-978-426-01 INDICATOR (NO.)
352 4-944-490-01 BELT (TIMING) * 366 1-659-059-13 BD LED BOARD
353 A-4660-978-A GEAR (PULLEY) ASSY * 367 1-659-058-13 TABLE SENSOR BOARD
354 4-978-421-01 GEAR (MID) 368 4-985-672-01 SCREW (+PTPWH M2.6), FLOATING
355 4-978-425-01 ROLLER (CAM) 369 4-958-593-01 SPRING (BU), COMPRESSION
– 88 –
Downloaded from www.Manualslib.com manuals search engine
(9) BASE UNIT SECTION
(BU-5BD29AL)
401
402
#12
403
404
406
407
408
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
! 401 8-820-020-01 OPTICAL PICK-UP KSS-213D/Q-NP 406 4-917-564-01 GEAR (P), FLATNESS
402 1-769-069-11 WIRE (FLAT TYPE) (16 CORE) * 407 A-4699-522-A BD BOARD, COMPLETE
403 4-917-567-21 GEAR (M) 408 4-951-620-01 SCREW (2.6X8), +BVTP
404 4-951-940-01 INSULATOR (BU) M101 X-4917-504-1 MOTOR ASSY (SPINDLE)
405 4-917-565-01 SHAFT, SLED M102 X-4917-523-4 MOTOR ASSY (SLED)
– 89 –
Downloaded from www.Manualslib.com manuals search engine
SECTION 9
AUDIO ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in the • Items marked “*” are not stocked since they The components identified by
parts list may be different from the parts speci- are seldom required for routine service. mark ! or dotted line with mark
fied in the diagrams or the components used Some delay should be anticipated when order- ! are critical for safety.
Replace only with part number
on the set. ing these items. specified.
• -XX and -X mean standardized parts, so they • SEMICONDUCTORS
may have some difference from the original In each case, u: µ, for example: When indicating parts by reference
one. uA. . : µA. . uPA. . : µPA. . number, please include the board.
• RESISTORS uPB. . : µPB. . uPC. . : µPC. .
All resistors are in ohms. uPD. . : µPD. .
METAL: Metal-film resistor. • CAPACITORS
METAL OXIDE: Metal oxide-film resistor. uF: µF
F: nonflammable • COILS
• Abbreviation uH: µH
AR : Argentine SAF : South African
AUS : Australian MX : Mexican
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* A-2007-131-A AUDIO BOARD, COMPLETE
********************** < CONNECTOR >
(including MOTOR BOARD)
CN601 1-695-382-31 PIN, CONNECTOR (PC BOARD) 21P
< CAPACITOR > CN602 1-564-718-11 PIN, CONNECTOR (SMALL TYPE) 2P
* CN651 1-564-521-11 PLUG, CONNECTOR 6P
C301 1-162-289-31 CERAMIC 390PF 10% 50V
C302 1-126-968-11 ELECT 100uF 20% 6.3V < IC >
C303 1-162-282-31 CERAMIC 100PF 10% 50V
C304 1-130-483-00 MYLAR 0.01uF 5% 50V IC601 8-759-111-44 IC uPC4570C-1
C305 1-107-715-11 ELECT 22uF 20% 16V IC602 8-759-143-54 IC uPC1330HA
IC611 8-759-111-44 IC uPC4570C-1
C311 1-162-289-31 CERAMIC 390PF 10% 50V
C313 1-162-282-31 CERAMIC 100PF 10% 50V < COIL >
C314 1-130-487-00 MYLAR 0.022uF 5% 50V
C315 1-126-233-11 ELECT 22uF 20% 50V L331 1-410-780-11 INDUCTOR 27mH
C331 1-137-427-11 FILM 120PF 5% 50V L431 1-410-780-11 INDUCTOR 27mH
– 90 –
Downloaded from www.Manualslib.com manuals search engine
AUDIO BD
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C126 1-163-038-91 CERAMIC CHIP 0.1uF 25V
R601 1-249-409-11 CARBON 220 5% 1/4W
R602 1-249-409-11 CARBON 220 5% 1/4W C127 1-164-161-11 CERAMIC CHIP 0.0022uF 10% 100V
R608 1-249-409-11 CARBON 220 5% 1/4W C128 1-163-135-00 CERAMIC CHIP 560PF 5% 50V
R609 1-249-433-11 CARBON 22K 5% 1/4W C129 1-163-038-91 CERAMIC CHIP 0.1uF 25V
R611 1-249-409-11 CARBON 220 5% 1/4W C130 1-164-336-11 CERAMIC CHIP 0.33uF 25V
C131 1-164-346-11 CERAMIC CHIP 1uF 16V
R612 1-249-409-11 CARBON 220 5% 1/4W
! R621 1-212-851-00 FUSIBLE 5.6 5% 1/4W F C140 1-110-501-11 CERAMIC CHIP 0.33uF 10% 16V
! R622 1-212-851-00 FUSIBLE 5.6 5% 1/4W F C154 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
R623 1-249-432-11 CARBON 18K 5% 1/4W C161 1-164-005-11 CERAMIC CHIP 0.47uF 25V
R624 1-249-432-11 CARBON 18K 5% 1/4W C162 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C163 1-163-117-00 CERAMIC CHIP 100PF 5% 50V
R625 1-249-429-11 CARBON 10K 5% 1/4W
R651 1-247-856-00 CARBON 11K 5% 1/4W C164 1-163-145-00 CERAMIC CHIP 0.0015uF 5% 50V
R652 1-247-856-00 CARBON 11K 5% 1/4W C165 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
R653 1-249-441-11 CARBON 100K 5% 1/4W C166 1-163-137-00 CERAMIC CHIP 680PF 5% 50V
C167 1-163-121-00 CERAMIC CHIP 150PF 5% 50V
C168 1-163-137-00 CERAMIC CHIP 680PF 5% 50V
< VARIABLE RESISTOR >
C169 1-163-121-00 CERAMIC CHIP 150PF 5% 50V
RV301 1-238-598-11 RES, ADJ, CARBON 2.2K C170 1-163-099-00 CERAMIC CHIP 18PF 5% 50V
RV311 1-238-598-11 RES, ADJ, CARBON 2.2K C171 1-163-237-11 CERAMIC CHIP 27PF 5% 50V
RV341 1-238-551-11 RES, ADJ, CARBON 220K C173 1-163-038-91 CERAMIC CHIP 0.1uF 25V
RV401 1-238-598-11 RES, ADJ, CARBON 2.2K C174 1-163-038-91 CERAMIC CHIP 0.1uF 25V
RV411 1-238-598-11 RES, ADJ, CARBON 2.2K
C175 1-163-038-91 CERAMIC CHIP 0.1uF 25V
RV441 1-238-551-11 RES, ADJ, CARBON 220K C176 1-163-038-91 CERAMIC CHIP 0.1uF 25V
RV651 1-238-599-11 RES, ADJ, CARBON 4.7K C177 1-163-038-91 CERAMIC CHIP 0.1uF 25V
RV652 1-238-599-11 RES, ADJ, CARBON 4.7K C178 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C179 1-163-038-91 CERAMIC CHIP 0.1uF 25V
< TRANSFORMER >
C181 1-126-205-11 ELECT CHIP 47uF 20% 6.3V
T621 1-423-980-11 TRANSFORMER, BIAS OSCILLATION C182 1-126-393-11 ELECT 33uF 20% 10V
************************************************************ C183 1-124-778-00 ELECT CHIP 22uF 20% 6.3V
C185 1-164-232-11 CERAMIC CHIP 0.01uF 50V
* A-4699-522-A BD BOARD, COMPLETE C188 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
*******************
C189 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
< CAPACITOR >
< CONNECTOR >
C101 1-126-607-11 ELECT CHIP 47uF 20% 4V
C102 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V CNU101 1-770-014-11 CONNECTOR, FFC/FPC 16P
C103 1-164-346-11 CERAMIC CHIP 1uF 16V CNU102 1-778-874-11 CONNECTOR, FFC(LIF(NON-ZIF))19P
C105 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C106 1-164-161-11 CERAMIC CHIP 0.0022uF 10% 100V < FERRITE BEAD >
C107 1-164-161-11 CERAMIC CHIP 0.0022uF 10% 100V FB101 1-414-234-11 INDUCTOR, FERRITE BEAD
C108 1-164-232-11 CERAMIC CHIP 0.01uF 50V FB103 1-414-234-11 INDUCTOR, FERRITE BEAD
C109 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C110 1-163-989-11 CERAMIC CHIP 0.033uF 10% 25V < IC >
C111 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V
IC101 8-752-080-62 IC CXA1992AR
C112 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V IC102 8-759-429-32 IC BA5941FP-E2
C113 1-164-161-11 CERAMIC CHIP 0.0022uF 10% 100V IC103 8-752-378-66 IC CXD2519Q
C114 1-164-005-11 CERAMIC CHIP 0.47uF 25V
C115 1-126-607-11 ELECT CHIP 47uF 20% 4V < CHIP CONDUCTOR >
C116 1-163-016-00 CERAMIC CHIP 0.0039uF 10% 50V
JW101 1-216-295-91 CONDUCTOR, CHIP (2012)
C117 1-164-005-11 CERAMIC CHIP 0.47uF 25V JW104 1-216-295-91 CONDUCTOR, CHIP (2012)
C118 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C119 1-163-038-91 CERAMIC CHIP 0.1uF 25V < TRANSISTOR >
C120 1-124-779-00 ELECT CHIP 10uF 20% 16V
C121 1-163-038-91 CERAMIC CHIP 0.1uF 25V Q101 8-729-010-08 TRANSISTOR MSB710-R
R175 1-216-025-91 METAL GLAZE 100 5% 1/10W S201 1-762-587-11 SWITCH, PUSH (1 KEY) (UP)
R176 1-216-025-91 METAL GLAZE 100 5% 1/10W ************************************************************
R177 1-216-025-91 METAL GLAZE 100 5% 1/10W
R178 1-216-025-91 METAL GLAZE 100 5% 1/10W * 1-664-019-11 CD-A SW BOARD
R179 1-216-025-91 METAL GLAZE 100 5% 1/10W **************
– 92 –
Downloaded from www.Manualslib.com manuals search engine
CD-A SW CD-B1 SW CD-B2 SW DOOR SW HP/MIC
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
< RESISTOR > < SWITCH >
R731 1-249-411-11 CARBON 330 5% 1/4W S681 1-554-303-21 SWITCH, TACTILE ())
R732 1-249-413-11 CARBON 470 5% 1/4W S682 1-554-303-21 SWITCH, TACTILE (REPEAT)
R733 1-249-415-11 CARBON 680 5% 1/4W S683 1-554-303-21 SWITCH, TACTILE (PLAY MODE)
R734 1-249-417-11 CARBON 1K 5% 1/4W S684 1-554-303-21 SWITCH, TACTILE (1/ALL DISCS)
R735 1-249-419-11 CARBON 1.5K 5% 1/4W S685 1-554-303-21 SWITCH, TACTILE (EDIT)
R736 1-249-421-11 CARBON 2.2K 5% 1/4W S686 1-554-303-21 SWITCH, TACTILE (0)
R737 1-249-417-11 CARBON 1K 5% 1/4W S711 1-467-968-11 ENCODER, ROTARY (≠ AMS ±)
R741 1-247-807-31 CARBON 100 5% 1/4W ************************************************************
S676 1-554-303-21 SWITCH, TACTILE (·) C797 1-162-302-11 CERAMIC 0.0022uF 20% 16V
S677 1-554-303-21 SWITCH, TACTILE (p) C798 1-164-159-21 CERAMIC 0.1uF 50V
S678 1-554-303-21 SWITCH, TACTILE (P) C799 1-164-159-21 CERAMIC 0.1uF 50V
S679 1-554-303-21 SWITCH, TACTILE (DISC SKIP)
************************************************************ < CONNECTOR >
– 93 –
Downloaded from www.Manualslib.com manuals search engine
HP/MIC LEAF SWITCH LED MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
< RESISTOR >
< RESISTOR >
R791 1-249-412-11 CARBON 390 5% 1/4W
R760 1-249-429-11 CARBON 10K 5% 1/4W ************************************************************
R761 1-249-417-11 CARBON 1K 5% 1/4W
R764 1-249-441-11 CARBON 100K 5% 1/4W * A-4403-844-A MAIN BOARD, COMPLETE
R765 1-249-417-11 CARBON 1K 5% 1/4W (XB66: E, MX, AR/XB660)
R766 1-247-863-91 CARBON 22K 5% 1/4W * A-4407-366-A MAIN BOARD, COMPLETE (XB66: AUS, SAF)
*********************
R767 1-249-429-11 CARBON 10K 5% 1/4W
R769 1-247-885-00 CARBON 180K 5% 1/4W * 4-870-539-11 PLATE, GROUND
R770 1-247-807-31 CARBON 100 5% 1/4W 7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
RV760 1-225-366-11 RES, VAR, CARBON 50K (MIC LEVEL) C100 1-164-159-21 CERAMIC 0.1uF 50V
************************************************************ C102 1-162-282-31 CERAMIC 100PF 10% 50V
C103 1-162-282-31 CERAMIC 100PF 10% 50V
* 1-650-669-11 LEAF SWITCH BOARD C104 1-126-961-11 ELECT 2.2uF 20% 50V
****************** C105 1-162-600-11 CERAMIC 0.0047uF 30% 16V
Q1001 8-749-010-90 TRANSISTOR PHOTO REFLECTOR C152 1-162-282-31 CERAMIC 100PF 10% 50V
NJL5165KA-H C153 1-162-282-31 CERAMIC 100PF 10% 50V
Q1002 8-749-010-90 TRANSISTOR PHOTO REFLECTOR C154 1-126-961-11 ELECT 2.2uF 20% 50V
NJL5165KA-H C155 1-162-600-11 CERAMIC 0.0047uF 30% 16V
C156 1-162-301-11 CERAMIC 0.0015uF 30% 16V
< RESISTOR >
C157 1-126-956-91 ELECT 0.1uF 20% 50V
R1001 1-247-818-11 CARBON 300 5% 1/4W C171 1-162-286-21 CERAMIC 220PF 10% 50V
R1002 1-247-820-11 CARBON 360 5% 1/4W C172 1-162-286-21 CERAMIC 220PF 10% 50V
R1003 1-249-414-11 CARBON 560 5% 1/4W C173 1-162-306-11 CERAMIC 0.01uF 20% 16V
R1004 1-247-834-11 CARBON 1.3K 5% 1/4W C191 1-126-963-11 ELECT 4.7uF 20% 50V
R1005 1-247-818-11 CARBON 300 5% 1/4W
C192 1-164-159-21 CERAMIC 0.1uF 50V
< SWITCH > C201 1-136-167-00 FILM 0.15uF 5% 50V
C202 1-136-167-00 FILM 0.15uF 5% 50V
S1001 1-692-832-11 SWITCH, PUSH (1 KEY) (DECK A PLAY) C203 1-130-493-00 MYLAR 0.068uF 5% 50V
S1002 1-692-832-11 SWITCH, PUSH (1 KEY) (DECK B PLAY) C204 1-130-493-00 MYLAR 0.068uF 5% 50V
S1003 1-572-248-11 SWITCH, LEAF (DECK A HALF)
S1004 1-571-281-21 SWITCH, LEAF (DECK A 120/70) C205 1-130-486-00 MYLAR 0.018uF 10% 50V
S1005 1-571-281-21 SWITCH, LEAF (DECK A REC) C206 1-130-486-00 MYLAR 0.018uF 10% 50V
C207 1-130-480-00 MYLAR 0.0056uF 5% 50V
S1006 1-572-248-11 SWITCH, LEAF (DECK B HALF) C208 1-130-479-00 MYLAR 0.0047uF 5% 50V
S1008 1-571-281-21 SWITCH, LEAF (DECK B 120/70) C209 1-130-474-00 MYLAR 0.0018uF 5% 50V
S1009 1-571-281-21 SWITCH, LEAF (DECK B REC)
************************************************************ C210 1-126-964-11 ELECT 10uF 20% 50V
C211 1-126-964-11 ELECT 10uF 20% 50V
* 1-664-017-11 LED BOARD C212 1-130-483-00 MYLAR 0.01uF 5% 50V
********** C213 1-136-169-00 FILM 0.22uF 5% 50V
C214 1-136-169-00 FILM 0.22uF 5% 50V
< CONNECTOR >
C215 1-162-294-31 CERAMIC 0.001uF 10% 50V
CN671 1-506-481-11 PIN, CONNECTOR 2P C216 1-136-167-00 FILM 0.15uF 5% 50V
C221 1-126-967-11 ELECT 47uF 20% 10V
< DIODE > C222 1-126-967-11 ELECT 47uF 20% 10V
C223 1-126-964-11 ELECT 10uF 20% 50V
D671 8-719-058-03 DIODE SEL5423E-TP15 (BACK LIGHT)
D672 8-719-058-03 DIODE SEL5423E-TP15 (BACK LIGHT) C224 1-162-290-31 CERAMIC 470PF 10% 50V
D673 8-719-058-03 DIODE SEL5423E-TP15 (BACK LIGHT) C226 1-126-964-11 ELECT 10uF 20% 50V
D674 8-719-058-03 DIODE SEL5423E-TP15 (BACK LIGHT) C231 1-109-889-11 ELECT 1uF 20% 50V
C251 1-136-167-00 FILM 0.15uF 5% 50V
C252 1-136-167-00 FILM 0.15uF 5% 50V
– 94 –
Downloaded from www.Manualslib.com manuals search engine
MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C253 1-130-493-00 MYLAR 0.068uF 5% 50V C1506 1-126-964-11 ELECT 10uF 20% 50V
C254 1-130-493-00 MYLAR 0.068uF 5% 50V C1507 1-126-960-11 ELECT 1uF 20% 50V
C255 1-130-486-00 MYLAR 0.018uF 10% 50V
C256 1-130-486-00 MYLAR 0.018uF 10% 50V C1508 1-126-933-11 ELECT 100uF 20% 10V
C257 1-130-480-00 MYLAR 0.0056uF 5% 50V C1523 1-126-933-11 ELECT 100uF 20% 16V
C1531 1-164-159-21 CERAMIC 0.1uF 50V
C258 1-130-479-00 MYLAR 0.0047uF 5% 50V C1532 1-164-159-21 CERAMIC 0.1uF 50V
C259 1-130-474-00 MYLAR 0.0018uF 5% 50V C1533 1-164-159-21 CERAMIC 0.1uF 50V
C260 1-126-964-11 ELECT 10uF 20% 50V
C261 1-126-964-11 ELECT 10uF 20% 50V C1534 1-126-935-11 ELECT 470uF 20% 16V
C262 1-130-483-00 MYLAR 0.01uF 5% 50V C1551 1-130-479-00 MYLAR 0.0047uF 5% 50V
C1552 1-162-290-31 CERAMIC 470PF 10% 50V
C263 1-136-169-00 FILM 0.22uF 5% 50V C1553 1-164-159-21 CERAMIC 0.1uF 50V
C264 1-136-169-00 FILM 0.22uF 5% 50V C1554 1-126-960-11 ELECT 1uF 20% 50V
C276 1-126-964-11 ELECT 10uF 20% 50V
C281 1-126-933-11 ELECT 100uF 20% 10V C1555 1-126-964-11 ELECT 10uF 20% 50V
C282 1-126-961-11 ELECT 2.2uF 20% 50V C1556 1-126-964-11 ELECT 10uF 20% 50V
C1557 1-126-960-11 ELECT 1uF 20% 50V
C283 1-126-933-11 ELECT 100uF 20% 10V C1558 1-126-933-11 ELECT 100uF 20% 10V
C284 1-126-923-11 ELECT 220uF 20% 10V
C291 1-126-959-11 ELECT 0.47uF 20% 50V < CONNECTOR >
C301 1-126-967-11 ELECT 47uF 20% 10V
C302 1-164-159-21 CERAMIC 0.1uF 50V CN101 1-778-982-11 CONNECTOR, BOARD TO BOARD 13P
* CN102 1-568-836-11 SOCKET, CONNECTOR 17P
C303 1-136-173-00 FILM 0.47uF 5% 50V * CN105 1-564-518-11 PLUG, CONNECTOR 3P
C304 1-126-926-11 ELECT 1000uF 20% 10V * CN201 1-568-832-11 SOCKET, CONNECTOR 13P
C305 1-162-306-11 CERAMIC 0.01uF 20% 16V CN202 1-568-802-11 SOCKET, CONNECTOR 19P
C309 1-102-514-11 CERAMIC 22PF 5% 50V
C310 1-102-514-11 CERAMIC 22PF 5% 50V * CN203 1-568-936-11 PIN, CONNECTOR 9P
CN205 1-568-838-11 SOCKET, CONNECTOR 21P
C311 1-164-159-21 CERAMIC 0.1uF 50V * CN206 1-568-830-11 SOCKET, CONNECTOR 11P
C315 1-126-933-11 ELECT 100uF 20% 10V * CN207 1-568-449-11 HOUSING, CONNECTOR (PC BOARD) 3P
C316 1-136-165-00 FILM 0.1uF 5% 50V
C390 1-126-933-11 ELECT 100uF 20% 10V < DIODE >
C391 1-162-306-11 CERAMIC 0.01uF 20% 16V
D141 8-719-991-33 DIODE 1SS133T-77
C392 1-126-933-11 ELECT 100uF 20% 10V D142 8-719-991-33 DIODE 1SS133T-77
C393 1-126-925-11 ELECT 470uF 20% 10V D191 8-719-991-33 DIODE 1SS133T-77
C394 1-164-159-21 CERAMIC 0.1uF 50V D192 8-719-991-33 DIODE 1SS133T-77
C396 1-126-961-11 ELECT 2.2uF 20% 50V D291 8-719-991-33 DIODE 1SS133T-77
C398 1-126-961-11 ELECT 2.2uF 20% 50V
D301 8-719-200-82 DIODE 11ES2
C903 1-136-165-00 FILM 0.1uF 5% 50V D302 8-719-200-82 DIODE 11ES2
C904 1-126-937-11 ELECT 4700uF 20% 16V D303 8-719-991-33 DIODE 1SS133T-77
C906 1-126-933-11 ELECT 100uF 20% 10V D304 8-719-991-33 DIODE 1SS133T-77
C909 1-126-964-11 ELECT 10uF 20% 50V D305 8-719-991-33 DIODE 1SS133T-77
C910 1-126-933-11 ELECT 100uF 20% 10V
D306 8-719-991-33 DIODE 1SS133T-77
C911 1-126-964-11 ELECT 10uF 20% 50V D307 8-719-991-33 DIODE 1SS133T-77
C912 1-126-916-11 ELECT 1000uF 20% 6.3V D309 8-719-991-33 DIODE 1SS133T-77
C913 1-126-943-11 ELECT 2200uF 20% 25V D902 8-719-200-82 DIODE 11ES2
C914 1-126-767-11 ELECT 1000uF 20% 16V D903 8-719-200-82 DIODE 11ES2
C915 1-126-967-11 ELECT 47uF 20% 16V
D904 8-719-200-82 DIODE 11ES2
C916 1-164-159-21 CERAMIC 0.1uF 50V D905 8-719-200-82 DIODE 11ES2
C917 1-126-968-11 ELECT 100uF 20% 50V D906 8-719-200-82 DIODE 11ES2
C918 1-126-968-11 ELECT 100uF 20% 50V D907 8-719-200-82 DIODE 11ES2
C919 1-126-964-11 ELECT 10uF 20% 50V D908 8-719-200-82 DIODE 11ES2
C920 1-126-947-11 ELECT 47uF 20% 35V
D909 8-719-200-82 DIODE 11ES2
C953 1-136-165-00 FILM 0.1uF 5% 50V D910 8-719-982-27 DIODE MTZJ-33C
C954 1-126-768-11 ELECT 2200uF 20% 16V D911 8-719-109-89 DIODE RD5.6ESB2
C956 1-126-933-11 ELECT 100uF 20% 10V D912 8-719-991-33 DIODE 1SS133T-77
C1501 1-130-479-00 MYLAR 0.0047uF 5% 50V D913 8-719-200-82 DIODE 11ES2
C1502 1-162-290-31 CERAMIC 470PF 10% 50V
D914 8-719-200-82 DIODE 11ES2
C1503 1-164-159-21 CERAMIC 0.1uF 50V D915 8-719-935-69 DIODE UZL-11M1-TA
C1504 1-126-960-11 ELECT 1uF 20% 50V D951 8-719-991-33 DIODE 1SS133T-77
C1505 1-126-964-11 ELECT 10uF 20% 50V D952 8-719-991-33 DIODE 1SS133T-77
– 95 –
Downloaded from www.Manualslib.com manuals search engine
MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
Q1531 8-729-801-93 TRANSISTOR 2SD1387
< FERRITE BEAD >
Q1532 8-729-029-66 TRANSISTOR DTC114ESA
FB302 1-412-473-21 INDUCTOR 0uH Q1533 8-729-029-66 TRANSISTOR DTC114ESA
Q1534 8-729-119-77 TRANSISTOR 2SA1175-FEK
< IC > Q1535 8-729-029-66 TRANSISTOR DTC114ESA
– 97 –
Downloaded from www.Manualslib.com manuals search engine
MAIN PANEL
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R1504 1-247-840-00 CARBON 2.4K 5% 1/4W C604 1-126-960-11 ELECT 1uF 20% 50V
R1505 1-247-863-91 CARBON 22K 5% 1/4W C606 1-126-960-11 ELECT 1uF 20% 50V
R1506 1-249-421-11 CARBON 2.2K 5% 1/4W
C608 1-126-382-11 ELECT 100uF 20% 6.3V
R1507 1-249-428-11 CARBON 8.2K 5% 1/4W C610 1-162-306-11 CERAMIC 0.01uF 20% 16V
R1521 1-247-852-11 CARBON 7.5K 5% 1/4W C611 1-162-306-11 CERAMIC 0.01uF 20% 16V
R1522 1-249-422-11 CARBON 2.7K 5% 1/4W C612 1-126-967-11 ELECT 47uF 20% 50V
R1524 1-249-429-11 CARBON 10K 5% 1/4W C613 1-164-159-21 CERAMIC 0.1uF 50V
R1525 1-249-432-11 CARBON 18K 5% 1/4W
C621 1-126-960-11 ELECT 1uF 20% 50V
R1526 1-249-429-11 CARBON 10K 5% 1/4W C622 1-136-161-00 FILM 0.047uF 5% 50V
R1527 1-249-429-11 CARBON 10K 5% 1/4W C623 1-126-957-11 ELECT 0.22uF 20% 50V
R1531 1-247-843-11 CARBON 3.3K 5% 1/4W C624 1-126-957-11 ELECT 0.22uF 20% 50V
R1532 1-249-411-11 CARBON 330 5% 1/4W C625 1-162-306-11 CERAMIC 0.01uF 20% 16V
R1533 1-249-427-11 CARBON 6.8K 5% 1/4W
C626 1-126-957-11 ELECT 0.22uF 20% 50V
R1534 1-249-429-11 CARBON 10K 5% 1/4W C627 1-136-159-00 FILM 0.033uF 5% 50V
R1535 1-249-425-11 CARBON 4.7K 5% 1/4W C628 1-162-302-11 CERAMIC 0.0022uF 30% 16V
R1536 1-249-425-11 CARBON 4.7K 5% 1/4W C629 1-126-957-11 ELECT 0.22uF 20% 50V
R1541 1-249-425-11 CARBON 4.7K 5% 1/4W C630 1-162-293-31 CERAMIC 820PF 10% 50V
R1542 1-249-425-11 CARBON 4.7K 5% 1/4W
C631 1-126-957-11 ELECT 0.22uF 20% 50V
R1543 1-249-425-11 CARBON 4.7K 5% 1/4W C632 1-126-957-11 ELECT 0.22uF 20% 50V
R1544 1-249-417-11 CARBON 1K 5% 1/4W C641 1-162-286-21 CERAMIC 220PF 10% 50V
R1545 1-249-437-11 CARBON 47K 5% 1/4W C642 1-162-286-21 CERAMIC 220PF 10% 50V
R1546 1-249-437-11 CARBON 47K 5% 1/4W C643 1-162-286-21 CERAMIC 220PF 10% 50V
R1547 1-249-437-11 CARBON 47K 5% 1/4W
C644 1-162-286-21 CERAMIC 220PF 10% 50V
R1548 1-249-437-11 CARBON 47K 5% 1/4W C645 1-162-286-21 CERAMIC 220PF 10% 50V
R1551 1-247-863-91 CARBON 22K 5% 1/4W C646 1-162-286-21 CERAMIC 220PF 10% 50V
R1552 1-249-417-11 CARBON 1K 5% 1/4W C647 1-162-286-21 CERAMIC 220PF 10% 50V
R1553 1-249-426-11 CARBON 5.6K 5% 1/4W C648 1-162-286-21 CERAMIC 220PF 10% 50V
R1554 1-247-840-00 CARBON 2.4K 5% 1/4W
C649 1-162-286-21 CERAMIC 220PF 10% 50V
R1555 1-247-863-91 CARBON 22K 5% 1/4W C650 1-162-286-21 CERAMIC 220PF 10% 50V
R1556 1-249-421-11 CARBON 2.2K 5% 1/4W C651 1-162-286-21 CERAMIC 220PF 10% 50V
R1557 1-249-428-11 CARBON 8.2K 5% 1/4W C652 1-162-286-21 CERAMIC 220PF 10% 50V
C653 1-162-286-21 CERAMIC 220PF 10% 50V
< VARIABLE RESISTOR >
C654 1-162-286-21 CERAMIC 220PF 10% 50V
RV1501 1-238-598-11 RES, ADJ, CARBON 2.2K C655 1-162-286-21 CERAMIC 220PF 10% 50V
RV1551 1-238-598-11 RES, ADJ, CARBON 2.2K C656 1-162-286-21 CERAMIC 220PF 10% 50V
C695 1-164-159-21 CERAMIC 0.1uF 50V
< RELAY > C696 1-164-159-21 CERAMIC 0.1uF 50V
– 98 –
Downloaded from www.Manualslib.com manuals search engine
PANEL
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
D615 8-719-058-04 DIODE SEL5223S-TP15 (SUPER WOOFER) R613 1-249-401-11 CARBON 47 5% 1/4W
D616 8-719-058-04 DIODE SEL5223S-TP15 (EFFECT) R614 1-249-429-11 CARBON 10K 5% 1/4W
D617 8-719-058-04 DIODE SEL5223S-TP15 (ENTER) R615 1-249-429-11 CARBON 10K 5% 1/4W
D618 8-719-058-04 DIODE SEL5223S-TP15 (FILE 1) R617 1-249-429-11 CARBON 10K 5% 1/4W
R621 1-249-421-11 CARBON 2.2K 5% 1/4W
D619 8-719-058-04 DIODE SEL5223S-TP15 (FILE 2)
D620 8-719-058-04 DIODE SEL5223S-TP15 (FILE 3) R622 1-249-437-11 CARBON 47K 5% 1/4W
D621 8-719-058-04 DIODE SEL5223S-TP15 (FILE 4) R623 1-247-895-91 CARBON 470K 5% 1/4W
D622 8-719-058-04 DIODE SEL5223S-TP15 (FILE 5) R624 1-249-421-11 CARBON 2.2K 5% 1/4W
D623 8-719-058-04 DIODE SEL5223S-TP15 (P FILE) R625 1-249-437-11 CARBON 47K 5% 1/4W
R626 1-247-895-91 CARBON 470K 5% 1/4W
D624 8-719-058-04 DIODE SEL5223S-TP15 (OTHERS)
D625 8-719-058-04 DIODE SEL5223S-TP15 (MUSIC) R627 1-249-421-11 CARBON 2.2K 5% 1/4W
R628 1-249-437-11 CARBON 47K 5% 1/4W
< FERRITE BEAD > R629 1-247-895-91 CARBON 470K 5% 1/4W
R631 1-249-437-11 CARBON 47K 5% 1/4W
FB601 1-412-473-21 INDUCTOR 0uH R632 1-247-895-91 CARBON 470K 5% 1/4W
< FLUORESCENT INDICATOR TUBE > R633 1-247-897-11 CARBON 560K 5% 1/4W
R634 1-247-897-11 CARBON 560K 5% 1/4W
FL601 1-517-617-11 INDICATOR TUBE, FLUORESCENT R635 1-247-897-11 CARBON 560K 5% 1/4W
R636 1-247-897-11 CARBON 560K 5% 1/4W
< IC > R637 1-247-895-91 CARBON 470K 5% 1/4W
– 99 –
Downloaded from www.Manualslib.com manuals search engine
PANEL POWER AMP
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R678 1-249-415-11 CARBON 680 5% 1/4W < VIBRATOR >
R679 1-249-419-11 CARBON 1.5K 5% 1/4W
X601 1-579-125-11 VIBRATOR, CERAMIC (8MHz)
R681 1-249-429-11 CARBON 10K 5% 1/4W ************************************************************
R682 1-249-421-11 CARBON 2.2K 5% 1/4W
R683 1-247-887-00 CARBON 220K 5% 1/4W * A-4403-848-A POWER AMP BOARD, COMPLETE
R684 1-249-421-11 CARBON 2.2K 5% 1/4W ***************************
R685 1-247-815-91 CARBON 220 5% 1/4W
7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
R686 1-247-807-31 CARBON 100 5% 1/4W
R687 1-247-807-31 CARBON 100 5% 1/4W < CAPACITOR >
R688 1-247-807-31 CARBON 100 5% 1/4W
R689 1-247-807-31 CARBON 100 5% 1/4W C801 1-126-963-11 ELECT 4.7uF 20% 50V
R690 1-247-807-31 CARBON 100 5% 1/4W C802 1-162-286-21 CERAMIC 220PF 10% 50V
C803 1-162-282-31 CERAMIC 100PF 10% 50V
R691 1-247-807-31 CARBON 100 5% 1/4W C804 1-126-967-11 ELECT 47uF 20% 10V
R692 1-247-807-31 CARBON 100 5% 1/4W C806 1-126-967-11 ELECT 47uF 20% 50V
R693 1-247-807-31 CARBON 100 5% 1/4W
R694 1-247-807-31 CARBON 100 5% 1/4W C807 1-126-965-11 ELECT 22uF 20% 50V
R695 1-247-807-31 CARBON 100 5% 1/4W C809 1-126-965-11 ELECT 22uF 20% 50V
C810 1-164-159-21 CERAMIC 0.1uF 50V
R696 1-247-807-31 CARBON 100 5% 1/4W C811 1-130-493-00 MYLAR 0.068uF 5% 50V
R697 1-247-807-31 CARBON 100 5% 1/4W C812 1-130-493-00 MYLAR 0.068uF 5% 50V
R698 1-247-807-31 CARBON 100 5% 1/4W
R699 1-247-807-31 CARBON 100 5% 1/4W C813 1-162-294-31 CERAMIC 0.001uF 10% 50V
R700 1-247-807-31 CARBON 100 5% 1/4W C821 1-126-963-11 ELECT 4.7uF 20% 50V
C822 1-162-286-21 CERAMIC 220PF 10% 50V
< SWITCH > C823 1-162-282-31 CERAMIC 100PF 10% 50V
C824 1-126-967-11 ELECT 47uF 20% 10V
S601 1-554-303-21 SWITCH, TACTILE (ENTER/NEXT)
S602 1-554-303-21 SWITCH, TACTILE (TUNER MEMORY) C826 1-126-967-11 ELECT 47uF 20% 50V
S603 1-554-303-21 SWITCH, TACTILE (TUNING MODE) C827 1-126-965-11 ELECT 22uF 20% 50V
S604 1-554-303-21 SWITCH, TACTILE (TUNER/BAND) C829 1-126-965-11 ELECT 22uF 20% 50V
S605 1-554-303-21 SWITCH, TACTILE (TUNING +) C830 1-164-159-21 CERAMIC 0.1uF 50V
C831 1-130-493-00 MYLAR 0.068uF 5% 50V
S606 1-554-303-21 SWITCH, TACTILE (TUNING -)
S607 1-554-303-21 SWITCH, TACTILE (STEREO/MONO) C832 1-130-493-00 MYLAR 0.068uF 5% 50V
S609 1-554-303-21 SWITCH, TACTILE (FUNCTION) C833 1-162-294-31 CERAMIC 0.001uF 10% 50V
S610 1-554-303-21 SWITCH, TACTILE (GROOVE) C841 1-136-165-00 FILM 0.1uF 5% 50V
S611 1-554-303-21 SWITCH, TACTILE (GEQ 4) C842 1-126-307-11 ELECT 6800uF 20% 50V
C843 1-126-925-11 ELECT 470uF 20% 10V
S612 1-554-303-21 SWITCH, TACTILE (GEQ 9)
S613 1-554-303-21 SWITCH, TACTILE (GEQ () C851 1-126-963-11 ELECT 4.7uF 20% 50V
S614 1-554-303-21 SWITCH, TACTILE (GEQ $) C852 1-162-286-21 CERAMIC 220PF 10% 50V
S615 1-554-303-21 SWITCH, TACTILE (SUPER WOOFER) C853 1-162-282-31 CERAMIC 100PF 10% 50V
S616 1-554-303-21 SWITCH, TACTILE (SUPER W MODE) C854 1-126-967-11 ELECT 47uF 20% 10V
C856 1-126-967-11 ELECT 47uF 20% 50V
S619 1-554-303-21 SWITCH, TACTILE (GEQ CONTROL)
S620 1-554-303-21 SWITCH, TACTILE (ENTER) C857 1-126-965-11 ELECT 22uF 20% 50V
S621 1-554-303-21 SWITCH, TACTILE (EFFECT) C858 1-126-963-11 ELECT 4.7uF 20% 50V
S622 1-554-303-21 SWITCH, TACTILE (WAVE) C861 1-130-493-00 MYLAR 0.068uF 5% 50V
S623 1-554-303-21 SWITCH, TACTILE (KARAOKE PON/MPX) C862 1-130-493-00 MYLAR 0.068uF 5% 50V
C871 1-126-963-11 ELECT 4.7uF 20% 50V
S624 1-554-303-21 SWITCH, TACTILE (SURROUND)
S625 1-554-303-21 SWITCH, TACTILE (P FILE MEMORY) C872 1-162-286-21 CERAMIC 220PF 10% 50V
S627 1-554-303-21 SWITCH, TACTILE (SPECTRUM ANALYZER) C873 1-162-282-31 CERAMIC 100PF 10% 50V
S628 1-554-303-21 SWITCH, TACTILE (DISPLAY/DEMO) C874 1-126-967-11 ELECT 47uF 20% 10V
S629 1-554-303-21 SWITCH, TACTILE (I /u) C876 1-126-967-11 ELECT 47uF 20% 50V
C877 1-126-965-11 ELECT 22uF 20% 50V
S630 1-554-303-21 SWITCH, TACTILE (t/CLOCK SET)
S631 1-554-303-21 SWITCH, TACTILE (REC) C878 1-126-963-11 ELECT 4.7uF 20% 50V
S632 1-554-303-21 SWITCH, TACTILE (DAILY 1) C881 1-130-493-00 MYLAR 0.068uF 5% 50V
S633 1-554-303-21 SWITCH, TACTILE (DAILY 2) C882 1-130-493-00 MYLAR 0.068uF 5% 50V
S634 1-554-303-21 SWITCH, TACTILE (SLEEP) C891 1-136-165-00 FILM 0.1uF 5% 50V
C892 1-126-307-11 ELECT 6800uF 20% 50V
S701 1-473-392-11 ENCODER, ROTARY (VOLUME)
C893 1-126-925-11 ELECT 470uF 20% 10V
– 100 –
Downloaded from www.Manualslib.com manuals search engine
POWER AMP TABLE SENSOR TC-A SW
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
< CONNECTOR > R841 1-249-421-11 CARBON 2.2K 5% 1/4W
R842 1-249-429-11 CARBON 10K 5% 1/4W
CN801 1-778-981-11 CONNECTOR, BOARD TO BOARD 13P R843 1-247-887-00 CARBON 220K 5% 1/4W
R844 1-249-429-11 CARBON 10K 5% 1/4W
< DIODE > R851 1-249-417-11 CARBON 1K 5% 1/4W
S651 1-554-303-21 SWITCH, TACTILE (·) 156 1-777-868-11 WIRE (FLAT TYPE) (19 CORE)
S652 1-554-303-21 SWITCH, TACTILE (ª) ! 158 1-569-008-11 ADAPTOR, CONVERSION 2P (XB66: AR)
S653 1-554-303-21 SWITCH, TACTILE ()) ! 159 1-558-943-51 CORD, POWER (XB66: E, MX/XB660)
S654 1-554-303-21 SWITCH, TACTILE (0) ! 159 1-575-651-21 CORD, POWER (XB66: SAF, AR)
S655 1-554-303-21 SWITCH, TACTILE (p) ! 159 1-696-845-11 CORD, POWER (XB66: AUS)
**************
HARDWARE LIST
**************