Professional Documents
Culture Documents
Device hardware
Back inserted and drawn modules, strong and weak electricity separation; enhanced unit chassis
designed for resisting strong vibration and interference, which can be scattered installed on the
switch cabinet.
Using dual 32-bit high performance embedded microprocessor, RAM and flash memory with
large capacity; using SOC solution, which greatly enhanced the capability of data processing,logic
operation and information storage and advanced operational speed and reliability.
The device uses 16 high precision A/D for data acquisition, collecting 64 points per cycle, which has
high measuring accuracy.
The device can keep more than 400 recent event records and operation records.
It has liquid crystal display, English display and menu operation.
Main features
The whole series device has universal AC-DC Input Power, which has a wide adaptability :
Device has universal AC-DC auxiliary power supply, the maximum input voltage is 500V, it can
suitable for all kinds of complicated power supply place;
Device has universal AC-DC operation circuit and binary input circuit power supply, which can
apply to AC or DC power supply system.
The device has wide range of current input, 5A or 1A, the user can easily to selection or use.
The device has powerful communication function, standard device configure two-way Ethernet and
two-way RS485 communication interface and convenient for multiple networking mode,device has
flexible communication, which support IEC61850 (optional), IEC-103, TCP-103, IEC-104,
MODBUS-RTU and other communication protocols, facilitate communication with a variety of
convenient networking with various microcomputer monitoring or the protection and management.
The device has rigorous same time benchmark, which supports network time synchronization, PPS
(pulse per second), PPM (pulse per minute) or B codes and other time synchronization mode.
WGB-611A Line protection device
Catalogue
1 Device introduction.................................................................................................................................................1
2 Technical indexes.................................................................................................................................................... 3
3.1 Structures...........................................................................................................................................................6
3.2 Main plug-in......................................................................................................................................................6
3.3 Analog plug-in...................................................................................................................................................6
3.4 CPU plug-in.......................................................................................................................................................6
3.5 Signal plug-in.................................................................................................................................................... 6
3.6 BI&BO Plug-in................................................................................................................................................. 7
3.7 Man-Machine Interface Plug-in........................................................................................................................ 7
4 Device Function...................................................................................................................................................... 7
5 Auxiliary functions............................................................................................................................................... 15
1
WGB-611A Line protection device
6 Device instruction................................................................................................................................................. 15
7 Wiring instructions...............................................................................................................................................19
9.1 Debugging....................................................................................................................................................... 36
9.2 Program and hardware check.......................................................................................................................... 36
9.3 Binary input check.......................................................................................................................................... 36
9.4 Relay circuit check.......................................................................................................................................... 36
9.5 Analog input check..........................................................................................................................................37
9.6 Overall function test........................................................................................................................................ 37
9.7 Abnormality handing.......................................................................................................................................37
2
WGB-611A Line protection device
12 Accessories...........................................................................................................................................................38
13 Ordering instruction.......................................................................................................................................... 38
14 Attached drawings.............................................................................................................................................. 40
15 Appendix A (Menu).............................................................................................................................................44
3
WGB-611A Line protection device
1 Device introduction
WGB-611A Microcomputer-based line protection device (Hereinafter referred to as the device) mainly apply
to protect line and outgoing feeder of 35kV voltage class and under. It can be directly installed in the high voltage
switch cabinet or installed in a screen body.
1.1 Function configuration
Please refer to the table below.
Protective Functions Abbr
Three-stage directional overcurrent protection with
1 OC,OC2,OC3
undervoltage blocking
2 Overcurrent accelerating protection OC_Accel
3 Overload protection (trip/alarm) OvLd
Three-stage zero-sequence directional overcurrent ZeroOC1,ZeroOC2,
4
protection (trip/alarm) ZeroOC3
5 Zero-sequence overcurrent accelerating protection ZOC_Accel
6 Undervoltage load shedding protection UVLS
7 Under frequency load shedding protection UFLS
8 Automatic reclosing AR
9 Manual synchronization M-Sync
10 Bus voltage transformer supervision
VTS
11 Line voltage transformer supervision
12 Control loop check Control Loop Chk
13 Circuit breaker open position check CB Open Pos Chk
14 Handcart position check Handcart Pos Chk
15 Spring not store energy check Spring not-E Chk
1
WGB-611A Line protection device
Communication Functions
2
WGB-611A Line protection device
3
WGB-611A Line protection device
b. Static discharge test: The device can endure static discharge test specified in chapter 4 of
GB/T14598.14-2010 whose harsh grade is IV.
c. Radiate electromagnetic field immunity: The device can endure radiate electromagnetic field
disturbance test specified in chapter IV of GB/T14598.9-2010 whose harsh grade is III, test field
strength is 10V/m(effective value).
d. Electrical fast transient burst immunity test: The device can endure Electrical fast transient / burst
immunity test specified in chapter 4 of GB/T14598.10-2012 whose harsh grade is A
e. Surge immunity test: The device can endure surge disturbance test specified in chapter 4 of
GB/T14598.18—2012 whose harsh grade is IV.
f. Conducted emission immunity test: The device can endure Conducted emission immunity test
induced by radio-frequency field specified in chapter 4 of GB/T14598.17—2005 whose harsh
grade is III.
g. Power frequency magneticfield immunity test: The device can endure power frequency
magneticfield immunity tests specified in chapter 5 of GB/T17626.8-2006 whose harsh grade is
IV.
h. Electromagnetic emission test: The device can endure conducted emission limiting value specified
in 4.1 and radiated emission limiting value specified in 4.2 of GB/T14598.16-2002.
i. Power frequency immunity test: The device can endure power frequency immunity tests specified
in chapter 4 of GB/T14598.19-2007.
j. Pulsed magnet fists: The device can endure pulsed magnet field immunity tests specified in chapter
5 of GB/T17626.9-2011whose harsh grade is IV.
k. Damping oscillating magneticfield immunity tests: the device can endure Damping oscillating
magneticfield immunity tests specified in chapter 5 of GB/T17626.10-1998 whose harsh grade is
IV.
2.5 Insulating property
a. Insulation resistance: The insulation resistance value of each conductive circuit to ground (i.e. the
Enclosure or exposed uncharged metal parts), between AC circuit and DC circuit or between AC
current circuit and AC voltage circuit shall not be less than 100MΩ tested by tester with open
circuit voltage 500V.
b. Dielectric strength: Communication circuit and weak electricity input and output terminal such as
24V of the device can endure AC voltage 50Hz, 500V (effective value) over the ground for 1
minute without dielectric breakdown and flashover phenomenon; Other each conductive circuit to
ground (i.e. the Enclosure or exposed uncharged metal parts), between AC circuit and DC circuit or
between AC current circuit and AC voltage circuit can endure AC voltage of 50Hz, 2kV (effective
value) without dielectric breakdown and flashover phenomenon for 1minute.
c. Impulse voltage: Communication circuit and weak electricity input and output terminal such as
24V of the device can endure the standard lightning wave impact test of 1Kv (peak value) over the
ground, Other each conductive terminal to ground, between AC circuit and DC circuit or between
4
WGB-611A Line protection device
AC current circuit and AC voltage circuit can endure the standard lightning wave impact test of
5kV (peak value).
2.6 Mechanical property
a. Vibration Response: Device can endure vibration response test specified in chapter 4.2.1 of GB / T
11287-2000 whose harsh grade is I.
b. Vibration durability: Device can endure vibration durability test specified in chapter 4.2.2 of GB /
T 11287-2000 whose harsh grade is I.
c. Impact Response: Device can endure impact response test specified in chapter 4.2.1 of GB / T
14537-1993 whose harsh grade is I.
d. Impact durability: Device can endure impact durability test specified in chapter 4.2.2 of GB / T
14537-1993 whose harsh grade is I.
e. Collision: Device can endure collision test specified in chapter 4.3 of GB / T 14537-1993 whose
harsh grade is I.
f. Earthquake: Device can endure earthquake test specified in IEC 60255-21-3:1993 whose harsh
grade is I.
2.7 Adjusting range and error of protection setting value
a. Setting range
Current setting: 0.1A~75A;
AC voltage: 2V~100V;
Delay: 0s~100s.
b. Setting error
Current: < ±2.5% or 0.05A;
Voltage: < ±2.5% or ±0.25V;
Delay error: not exceed 40ms or ±2% within the scope of 0s-100s.
2.8 Measurement accuracy
a. The measuring error of each analog quantity is not exceed±0.2% of the rated value;
b. The measuring error of power is not exceed ±0.5% of rated value;
c. The measuring error of 4-20mA is not exceed ±0.02mA;
d. The resolution of binary input is not more than 2ms;
2.9 Contact capacity
a. In DC inductive loaded circuit, whose voltage is not more than 250V, current is not more than 1A
and time constant is 5ms±0.75ms, contact breaking capacity is 50W, allowed long-term current is
not more than 5A.
b. In AC circuit (Cos =0.4±0.1), whose voltage is not more than 250V, current is not more than 2A,
contact breaking capacity is 250VA, allowed long-term current is not more than 5A.
3 Device Hardware Description
Enhanced case designed for resisting strong vibration and interference to ensure device still has high
reliability when installed in harsh conditions. Whether the device is installed dispersedly or installed in compose
5
WGB-611A Line protection device
body, no additional AC input or DC input anti-interference module is needed. There are LCD, signal indicator
lamp, keyboard operation and RS-232 communication port in panel.
3.1 Structures
Overall dimension of the device is shown in Figure 3-1;the size of the mounting hole is shown in figure 3-2:
6
WGB-611A Line protection device
Tripping-closing circuit’ main function includes tripping, closing and self-holding, anti-trip, position
monitoring and so on. It includes tripping relay(TR), closing relay(CR), past closed position relay(PCPR), remote
control tripping relay(RCTR), remote control closing relay(RCCR), tripping holding relay(THR), closing holding
relay(CHR) and anti-trip relay(ATR).
Standby relay output includes six standby relay outputs, which can be set as momentary or maintained output
according to user needs.
3.6 BI&BO Plug-in
This plug-in includes input and output two part extension function, can complete extending input and output
of device, flexible configure more functions.
3.7 Man-Machine Interface Plug-in
Installed on the device panel, Man-Machine interface plug-in is the main components of device for
information exchange with the outside world. It uses a large-screen LCD, English menu display (operation). The
main functions are: keyboard operation, LCD display, signal light indicating and serial port debugging.
4 Device Function
4.1 Three-stage directional overcurrent protection with undervoltage blocking
The device is configured with directional overcurrent protection with undervoltage blocking, which include
stage 1 overcurrent protection (OC1), stage 2overcurrent protection (OC2) and stage 3 overcurrent protection
(OC3),each stage current setting and delay time setting can be set independently. By setting the control word, we
can decide to apply or quit the voltage element and direction element.
Inter-phase Power direction element of three-segment current protection adopts 90°wiring mode, and
compares the phases of Ia and Ubc, Ib and Uca, Ic and Uab, its action equation is shown as follows(Ia and Uab for
example):
Ubc
75 0 Arg j
75 0
Ia e
In the formula, φ is maximum sensitive angle, take φ =-45°(Inter-phase power direction sensitive angle value
is set to 1) or φ =-30° (Inter-phase power direction sensitive angle value is set to 0).
The schematic diagram of three-stage directional overcurrent protection with undervoltage blocking is shown
in figure 4-1.
7
WGB-611A Line protection device
Figure 4-1Schematic diagram of three-stage directional overcurrent protection with undervoltage blocking
4.2 Overcurrent accelerating protection
The device is configured with independent overcurrent accelerating protection, we can select accelerated
mode by means of setting the protection setting[Opt_OC_Accel] (1 denotes accelerated tripping before automatic
reclosing, 0 denotes accelerated tripping after automatic reclosing).Accelerated tripping before automatic
reclosing is generally used to protect radial lines with pieces of lines of the levels of voltage class under 35kV. It
can get rid of the fault rapidly, and correct the nonselective action by automatic reclosing.Accelerated tripping
after automatic reclosing is that lines are equipped with selective protection and automatic reclosing,when line
fault happens, protection trip selectively and then automatic reclosing, when manual switching-onto-fault or
automatic reclosing-onto-fault, past-accelerating protection trip non-preference, accelerate getting rid of the fault
rapidly.
The device has been set independent current setting and corresponding delay time setting of overcurrent
accelerating protection. Compared with the traditional protection, the configuration of protection is more flexible.
The schematic diagram of overcurrent accelerating protection is shown in figure 4-2.
or not. By setting protection setting “En_OvLd_Trip ”, we can choose to trip or alarm (“0” denotes alarm, and “1”
denotes trip). The schematic diagram of overload protection is shown in figure 4-3.
8
WGB-611A Line protection device
3U 0
750 Arg j
750
3I 0 e
In the formula, φ is maximum sensitive angle, take φ =90°or φ =-135°. The schematic diagram is shown in
figure 4-4.
9
WGB-611A Line protection device
10
WGB-611A Line protection device
11
WGB-611A Line protection device
12
WGB-611A Line protection device
13
WGB-611A Line protection device
14
WGB-611A Line protection device
6 Device instruction
6.1 STRAP_SET information
The virtual strap of device is set alone and carried out in the menu "SET" → "STRAP_SET". Strap list is
shown in table below.
15
WGB-611A Line protection device
16
WGB-611A Line protection device
17
WGB-611A Line protection device
OC1 Trip Tripping relay and tripping signal relay output; “TRIP” indicator lamp lights up
OC2 Trip Tripping relay and tripping signal relay output; “TRIP” indicator lamp lights up
OC3 Trip Tripping relay and tripping signal relay output; “TRIP” indicator lamp lights up
OC_Accel Trip Tripping relay and tripping signal relay output; “TRIP” indicator lamp lights up
OvLd Trip Tripping relay and tripping signal relay output; “TRIP” indicator lamp lights up
ZeroOC1 Trip Tripping relay and tripping signal relay output; “TRIP” indicator lamp lights up
ZeroOC2 Trip Tripping relay and tripping signal relay output; “TRIP” indicator lamp lights up
ZeroOC3 Trip Tripping relay and tripping signal relay output; “TRIP” indicator lamp lights up
ZOC_Accel Trip Tripping relay and tripping signal relay output; “TRIP” indicator lamp lights up
UVLS Trip Tripping relay and tripping signal relay output; “TRIP” indicator lamp lights up
UFLS Trip Tripping relay and tripping signal relay output; “TRIP” indicator lamp lights up
AR Op Closing relay and closing signal relay output; “CLOSE” indicator lamp lights up
18
WGB-611A Line protection device
19
WGB-611A Line protection device
service position (Up DC/Service) input terminal; 203 is the down disconnector /handcart test position (Down
DC/Test) input terminal; 204 is the earth switch input terminal; 205~210 are binary input 1(BI_1) to binary input
6 (BI_6) terminals(the user can define them oneself); 211 is the manual synchronization (Manual Sync) input
terminal; 212 is the block automatic reclosing (Block AR) input terminal; 213 is overhaul signal input terminal,
when overhaul strap is enabled, the device will shield all of the remote signals except overhaul state.
214 is the binary input common negative pole terminal for terminal 201~213, and is connected to negative
power supply (binary input power supply is strong electricity, if the input power supply is AC, you can ignore the
polarity).
401~410 are standby binary input 1 to binary input 10 input terminals; 411 is the binary input common
negative pole terminal for terminal 401~410, and is connected to negative power supply (binary input power
supply is strong electricity, if the input power supply is AC, you can ignore the polarity).
Moreover, the device also has five ways internal inputs, they are circuit breaker closed position (CB closed),
circuit breaker open position (CB open), past closed position (Past closed), manual trip and remote/local, this five
ways inputs wiring in the control loop, which will work automatically after control loop wiring correctly.
7.5 Binary output and control loop terminals
301 is the signal common terminal; 302, 303, 304 are the alarm signal, the tripping signal, the closing signal
terminal respectively; 305, 306 are the alarm output terminal of power outage.
315, 316 are tripping output; 324 is protection tripping entry terminal; 325 is manual tripping terminal; 326
should be connected with circuit breaker tripping coil.
317, 318 are closing output; 320 is manual closing terminal; 321 should be connected with breaker closing
coil.
319 is the circuit breaker closed position monitoring input terminal; 327 is the circuit breaker open position
monitoring input terminal.
322 is +CLPS (anode of control loop power supply) and 323 is –CLPS (cathode of control loop power
supply), both AC and DC power supply could be used as control power supply. Distinguish anode and cathode
when using DC power supply.
308, 309 are the accident sounding output terminals; 310, 311 are the control loop abnormal output terminals;
312, 313, 314 are standby output 1 output terminals, wherein the terminals 312, 313 is the normally open contact,
312, 314 is normally closed contact; 416 and 417 are standby output 2 output terminals, 418, 419 are standby
relay output 3 output terminals; 420, 421, 422 are standby output 4 output terminals, wherein the terminals 420,
421 is normally open contact, 420, 422 is the normally closed contact; 423, 424, 425 are standby output 5 output
terminals, wherein the terminals 423, 424 is normally open contact, 423, 425 is the normally closed contact; 426,
427, 428 are standby output 6 output terminals, wherein the terminals 426, 427 is normally open contact, 426, 428
is the normally closed contact.
7.6 GPS time synchronization
The 215, 216 are the GPS time synchronization input power supply terminals, 215 for anode, 216 for
cathode.In the mode of pulse time synchronization, the input power supply is DC 24V which is self-produced by
device or from external equipment.In the mode of B code time synchronization, it is need to pay attention to the
20
WGB-611A Line protection device
polarity.
7.7 Communications terminals
217, 218 are RS-4851 communication terminals, terminal 217 is 4851+, and 218 is 4851-.
219, 220 are RS-4852 communication terminals, terminal 219 is 4852+, and 220 is 4852-.
E1, E2 are two Ethernet communication interfaces.
7.8 4-20mA DC input and output terminals (Optional)
229-234 are three channels 4-20mA output terminals, 229,230 are the first channel current output terminals
DCOUT1+, DCOUT1-, 231, 232 are the second channel output terminals DCOUT2+, DCOUT2-, 233, 234 are the
third channel output terminals DCOUT3+, DCOUT3-. The 4-20mA output terminals wiring please refer to
attached drawing 3(schematic diagram of device wiring). External DC power supply for the circuit should not
exceed 36V; the load resistance should not exceed 500Ω.
235-242 are four channels 4-20mA DC input terminals, 235, 236 are the first channel current input terminals
DCIN1+, DCIN1-, 237, 238 are the channel current input terminals DCIN2+, DCIN2-, 239, 240 are the third
channel input terminals DCIN3+, DCIN3-, 241, 242 are fourth channel input terminals DCIN4+, DCIN4-. The
4-20mA input terminals wiring please refer to attached drawing 3(schematic diagram of device wiring). Please
note the current direction, the anode of each group of input terminals is terminal where current flows.
8 Display and keyboard instruction
8.1 Keyboard instruction
“ ”key: Move the cursor up;
“ ”key: Move the cursor down;
“ ”key: Move the cursor left;
“ ”key: Move the cursor right;
“+”key: Increase numerical value;
“-”key: Reduce numerical value;
“CR” key: Confirm the current modification or menu conversion;
“ESC”key: Return to the previous menu;
“RES” key: Signal reset key, used to reset record and signal indicator lamp.
8.2 Indicator lamp instruction
"RUN": when the device normal running, the indicator lamp flashes once per second.
"485-1": the indicator lamp lights up when 4851 communication with the host computer.
"485-2": the indicator lamp lights up when 4852 communication with the host compute.
"TRIP": The “TRIP” indicator lamp and the trip signal (terminal 301, 303) is synchronized, the indicator
lamp lights up as long as the trip signal outputs.
"CLOSE": The “CLOSE” indicator lamp and the close signal (terminal 301, 304) is synchronized, the
indicator lamp lights up as long as the close signal outputs.
"ALARM": The “ALARM” indicator lamp and the alarm signal (terminal 301, 302) is synchronized, the
indicator lamp lights up as long as the alarm signal outputs.
8.3 Running interface instruction
21
WGB-611A Line protection device
The left area displays the main wiring of the system, which includes the states of circuit breaker, up/down
disconnector and earth switch, also it can display the handcart service position and test position (configured in
“LCL” → “PARM_SET” menu); Right area displays analog quantities, it displays three-phase measured current
and three-phase phase-voltage, also it can display power or protective current (configured in “LCL”
→“PARM_SET” menu). Detailed configuration method refers to “PARM_SET” of menu “LCL” instruction in
chapter 8.10
Press “ESC” when display the interface above, it will display the following interface:
The above part of the interface is current running time of the device; “SG” indicates which setting group is
active, the range is between 0 and 7; “Addr” indicates the communication address of the device; the following two
lines represent two Ethernet IP address of the device.
8.4 Menu structure
The whole menu structure of device is shown as follow:
22
WGB-611A Line protection device
In the main menu, by pressing key to select the menu option you want to select, and press "CR" key to
enter the submenu of selected menu option. If the submenu has several options, use " , " to select the option
you want to view and press "CR" key, then you can view the contents of selected option. Press "ESC" key to
return to the previous menu.
8.5 Menu operation instruction
In the normal display mode or display action message or self-check message, press the "CR" key, device pop
up the main menu, As follows:
After entering the main menu, by pressing the , , , keys, we can switch between the main menu,
use , to move the cursor to select menu, and press “CR” to enter the function selected. There are submenus
in the main menu, we need password to enter some of the submenus and the default password is “9999”.
23
WGB-611A Line protection device
In the main menu, we can select “VIEW” by pressing , , and press “CR” key to enter the “VIEW”
menu, after entering, press , to move the cursor to select the data we want to browse. The “VIEW” menu
contains the following data units: “PROT DATA”, “MEASURE DATA”, “BI STATUS”, “ENERGY”, “STRAP
STATUS” and “PROT SETTING”. After selecting certain data unit,press “CR” key to enter and browse the related
data.
“PROT DATA”: To display the protective data, such as the protective current, voltage, zero sequence current
and so on; pressing , key can move the cursor and browse the related protective data,
the related name of the protective data will be displayed at the bottom of the screen.
“MEASURE DATA”: To display the measured data, such as the measured current, voltage, power, power factor
and so on; press , to move the cursor and browse the related measured data, the related
name of the measured data will be displayed at the bottom of the screen.
“BI STATUS”: To display the status of the binary inputs; press , , , key to move the cursor and browse
the related binary input, the related name of the binary input will be displayed at the bottom of
the screen. "1" indicates that the input is on, and “0” indicates that the input is off.
“ENERGY”: To display the current value of energy accumulation; press , key to move the cursor and
browse the related data, the related name of the energy quantity will be displayed at the bottom of
24
WGB-611A Line protection device
the screen. When the energy quantity record reaches maximum of its capacity, it will automatically
clear and start to count from zero.
“STRAP STATUS”: To display the status of protection function virtual strap(enable or disable); press ,
key to move the cursor and browse the related strap status, the related name of the strap will
be displayed at the bottom of the screen. "1" indicates the protection function is enabled,
and "0" indicates the protection function is disabled.
“PROT SETTING”: To display the protection setting of active setting group; after selecting the menu, it will
prompt us to input the group number, and we may press “+”, “-” key to modify it, if you
don't modify it and enter directly, it displays current group that the device running by; after
entering, press , key move the cursor and browse the related setting value, the related
name of the setting value will be displayed at the bottom of the screen.
Press “CR” to enter the “RECs” menu, press , key to select “ACTION_RECs”, “ALARM_RECs”,
“BI_CHG_RECs”, “OPERATE_RECs” or “CLEAR RECs”. When you want to browse the record, select the
option and press “CR” to enter, press "ESC" to quit browse. “CLEAR RECs” can delete the “ACTION_RECs”,
“ALARM_RECs”and “BI_CHG_RECs”. “OPERATE_RECs” do not allow users to delete.
25
WGB-611A Line protection device
“ACTION_RECs”: Protection action records, namely of the fault record produced by the protection action, press
“+” or “-” to show the next record, press , key can look at 10 records once,
press , key can check the current record content side by side, if the protection has no
failure quantity, press , key will do nothing. As shown below:
“ALARM_RECs”: Device alarm records, namely of predict record produced by the device, including alarm
record, self-check record. The method of operation is the same as “ACTION_RECs”.
“BI_CHG_RECs”: Record the change of binary input. The method of operation is the same as “ACTION_RECs”.
“OPERATE_RECs”: The records of operation and modify, for example: the setting value modify, parameters
modify, remote control operating records and so on.
“CLEAR RECs”: Delete history records that have been stored by the device, in order to prevent incorrect
operation, we must input password before carrying out the operation. The records that can be
deleted only include trip records, alarm records, and binary input change records; it is not
allowed to delete operation records.
8.8 “SET” menu instruction
Press “CR” key and input the correct password to enter the settings menu, we can press , to select
“STRAP_SET”, “SETTING_SET”,“SG_SWITCH ” or “SG_COPY”. Then press “CR” key to enter related
option.
26
WGB-611A Line protection device
“STRAP_SET”: In this menu, we may enable or disable the protection function. After entering the menu,
press , key to select the strap you want to modify, and press “+”, “-” key to change the
status of the strap, namely, device enable the protection function or disable it, "1" means the
related protection function has been enabled, "0" means the related protection function has been
disabled. As shown below:
After modifying the strap, press “ESC” key, the device will promote you whether to store the modification.
According to your need, choose “Yes” to store it, and choose"Esc" to quit it. As shown below:
“SETTING_SET”: Modify the protection setting value in certain group. When you select the menu, the default is
to modify the value of the current group, if you need to modify the value of other group, you
can press“+”, “-” key to modify the group number. Press , key to select the value
option you want to modify, and press , key to move the cursor in the position of
protection setting value, then press “+”, “-” key to increase or decrease the size of the data
value. After modifying the protection setting value, press "ESC" key, the device will prompt
you whether to save the modification, According to your need, choose “Yes” to store it, and
choose “Esc” to quit it.
27
WGB-611A Line protection device
“SG_SWITCH ”: Select “SG_SWITCH ”, the device will prompt you to input the setting group number you want
to switch, press “+”, “-”to input the setting group number what you want (the device has 8
setting groups to store value, the related setting group number is 0-7). The method of save is the
same as“SETTING_SET”.
Notice: once you switch the setting group, the setting value data for each protection function turn to the
setting value in the setting group which has been switched immediately, the setting group which has been
switched is the current running group of setting value, please make sure that the setting value in the setting group
is right before you switch it.
“SG_COPY”: Select “SG_COPY”, the device will prompt you to input the source setting group number of
setting value you want to copy and target setting group number, press “+”, “-”to input the
setting group number what you want (the device has 8 setting groups to store value, the related
setting group number is 0-7) . The method of save is the same as“SETTING_SET”.
28
WGB-611A Line protection device
Press “CR” to enter the test menu, you can press , key to select “ANALOG_CALBR”,
“RELAY_DRIVE” or “COMM_TEST”. Press “CR” to enter the option you select.
“ANALOG_CALBR”: Calibrate the analog quantity. Check whether the specified channel analog value is
consistent with the current input value, if not, we can press , key to select the analog
quantity need to calibrate and press “+”, “-”to calibrate it.
Notice: Each channel has been accurately calibrated before the device leaves the factory, it is not
recommended for user to calibrate it.
“RELAY_DRIVE”: Drive the relay and check whether the relay output is normal. Binary input [Overhaul]
(terminal n213) needs to be energized before driving the relay, it’s not allowed to drive the
relay during the device normal running; Press , key to select the relay you want to drive,
then press “CR” to make the relay action, thereby check whether the relay output is normal,
press “RES” key can reset corresponding signal. As shown below:
29
WGB-611A Line protection device
“COMM_TEST”: Send mimic records to background monitor system, and check whether the information
number,function code, sector number and other information which are configured in
background monitor system are correct. Press , key to select the type of the mimic
record:"Action info", "Alarm info ", "BI info "; Press , key to select the mimic record ,
press “CR” key and then press , key to select the "Ret" or "Op", and then press “CR” key
to send mimic record message, thereby check whether the information point of background
monitor system is configured correctly. As shown below:
Press “CR” key and then enter the correct password to enter the “LCL” menu, press , to move cursor to
the option you want to set. This menu includes the following option unit: “COMM_SET”, “ENERGY_SET”,
“CLOCK_SET”, “PWD_SET”, “PARM_SET”, “SELF-CHK_SET”, “OUTPUT_SET”, “OUTPUT_REVERT”,
“DC-OUT_SET”, after selecting an item menu, press “CR” to enter the corresponding setting object. After the
modification of an item data, press "ESC" and the device will prompt you whether to save the modification,
According to your need, choose “Yes” or“Esc”.
30
WGB-611A Line protection device
“COMM_SET”: After entering the menu, you can set the parameter about communication, including:
DevAddr(Device communication address), Protocol (Communication protocol type), BaudRate
(Communication baud rate), Parity(Parity mode), IP Addr (Internet Protocol Address), Subnet
Mask, Gateway Addr (Gateway Address);After entering the menu, press , key to select the
parameter option we want to modify and press “+”,“-” key to change the corresponding parameter.
As shown below:
DevAddr: Display and modify the device communication address. When communicating with
background monitor system, just set the device address as corresponding address of background
monitor system.According to the need, we can modify hundred digit, tens digit, unit digit respectively,
press , key to move the cursor and press “+”, “-” key to modify the address.
Protocol: Display and modify the communication protocol type.There are two types (IEC103 and
ModBus) to select, press “+”, “-” key to switch protocol type.
BaudRate: Display and modify the communication baud rate. There are three kinds of baud rate
(4800bps, 9600bps and 19200bps) to select, press“+”, “-”key to switch communication baud rate.
Parity: Display and modify the parity. There are three kinds of parity mode(None (no parity), Even
(even-parity) and Odd (odd-parity)) to select, press“+”, “-”key to switch parity mode.
IP Addr, Subnet Mask, Gateway Addr:Press , key to select parameter option we want to modify,
each parameter is set in bits, press , key to select set bit and press the "+", "-" key to modify set
bit.
Note: when the device RS485-1 communicate with the background monitor system normally, the "485
1" indicator lamp on the device panel lights up, when the device RS485-2 communicate with the
background monitor system normally, the "485 2" indicator lamp on the device panel lights up; A-net
setting corresponds to the Ethernet E1 of device, B-net setting corresponds to the Ethernet E2 of
device,.
31
WGB-611A Line protection device
“ENERGY_SET”: To set the initial value of energy; When the device has been put into operation, we can set the
initial value of related energy in order to meet the need of energy measuring; Press , key
to select energy option you want to modify, and press , key to move the cursor position
located in the energy data (unit, ten, hundred, thousand ……),and press “+”,“-” key to
increase or decrease the size of the data.
“CLOCK_SET”: To set the current time of the device; if the running time of the device is inconsistent with the
current time, we can enter this menu to modify it, after modifying it, press “ESC” and the device
will prompt whether to save the modification. The user can decide save it or not.
“PWD_SET”: Tomodify the device password; In order to limit user modifying the important option, we add a
password to the device part of the menu, please careful operation with the menu which has set
password; The initial password is “9999”, when put into operation, users can set the appropriate
password according to their needs, when modify the password, it is needed to enter the old
password and enter the new password twice, the two password must be consistent, after
modification, press “ESC” and the device will prompt whether to save it. The user can decide save
it or not.
“PARM_SET”: After entering the menu, we can set the following options: CTRatio (current transformer ratio),
VTRatio (voltage transformer ratio), CBType(circuit breaker type) , DSPMode (analog display
mode), DSPType (analog display type), SOEMode (SOE reset mode), GPSMode(GPS time
synchronization mode), TWO-MCT (two-phase measuring currents); After entering the menu,
press , key to select the parameter need to be modified,then press“+”, “-” key to change the
size of the corresponding parameter.
32
WGB-611A Line protection device
CTRatio,VTRatio: Ratio of current transformer and voltage transformer, we can input the ratio of
current transformer and voltage transformer which are used during the actual operation (for example, if
the ratio of CT is 100:5, then we will set to 20 in our device; if the ratio of VT is 10000:100, then we
will set to 100 in our device), setting the ratio will not influence our protection function (the protection
still use the secondary side analog quantity actually collected by device), its role is merely display the
primary side analog quantity in the first screen. If not set the option, the data shown in the first screen
defaults to the secondary side analog quantity actually collected by device.
CBType: The type of circuit breaker, which is provided for sett he content displayed on the left part of
the first screen. When the option is set to “0”, the area will display the wiring mode of the fixed breaker;
when the option is set to “1”, the area will display the wiring mode of the handcart breaker. For
example:
CBType =0(fixed breaker)wiring mode: CBType =1 (handcart breaker) wiring mode:
DSPMode: The analog quantity display mode, which is provided for set the content displayed on the
right part of the first screen. When the option is set to “0”, this area will display three-phase measuring
current and three-phase measuring voltage, When the option is set to “1”, the area will display the
active power, reactive power, power factor and system frequency of device;
DSPType: The analog quantity display type, when the option is set to “0”, the first screen of the device
will display three-phase measuring current; When the option is set to “1”, the first screen of the device
will display three-phase protection current. It is suggested that when the CT you use has no measuring
current output, please set to 1, then the first screen will display protection current, so you can check the
system current in real time.
SOEMode: SOE reset mode, "auto"means automatic reset and "manual" means manual reset.
GPSMode: GPS time synchronization mode, "NO"means no GPS time synchronization (if no external
GPS, please set to "NO"), "PPS"means pulse per second time synchronization, "PPM"means pulse per
minute time synchronization, "BCode" means IRIG-B(DC) time synchronization.
TWO-MCT: Two-phase measuring currents, when the option is set to “0”, power calculation involve
three-phase current; set to"1", device use the two-meter method to calculate power.
“SELF-CHK_SET”: After entering this menu, we can set CtrlLoopChk (Control loop abnormal check),
OpenPosChk (Open position abnormal check) and HandcartChk (Handcart position
abnormal check); when the option is set to “0”, it means that the self-checking function is
disabled; otherwise,when the option is set to “1”, it means the self-checking function is
enabled. The three self-checking function above are enabled when leaving factory.
33
WGB-611A Line protection device
“OUTPUT_SET”: To configure the output of six standby relays, which are used for expanding the outputs in
specific application;The standby relay outputs do not influence the normal trip output and
alarm output, it is used to expand protection output or alarm output, for example, overload
alarm expand the standby relay output 1, that is,at the time the overload alarm normally act,
device drive standby relay output 1 to act,user can configure the six standby relay outputs
respectively according to the need, the output can be configured as momentary or maintained
output.
In the“Set output”interface, each standby relay output correspond to a16-bit hexadecimal number, which is
divided into the low byte “n Drv_L”(for tripping, n=1~6) and high byte “n Drv_H” (for alarm, n=1~6), from right
to left, the hexadecimal number is from D0 to D15respectively. For example:
Each bit of the 16-bit hexadecimal number corresponds to four different protection functions, and each
protection function corresponds to a data. Specific corresponding relation is shown in the following table:
Bit
D7 D6 D5 D4 D3 D2 D1 D0
Corresponding value
Warning RC_tripping
0x02 / / / UVLS Trip ZeroOC1 Trip OC2 Trip
signal 2
34
WGB-611A Line protection device
Bit
D15 D14 D13 D12 D11 D10 D9 D8
Corresponding value
When users need to configure multiple protection functions and these protection functions are in the same
hexadecimal bit, the user should enter the sum of the corresponding values of these protection functions.
For example: If the users need standby relay output1 contact to act when “OC1Trip”, “OC2Trip”, or
“OC_Accel Trip” , and need standby relay output 3 contact to act when “OvLd Alarm” , users can configure refer
to the following method:
Check the table above and we can find that “OC1Trip”, “OC2Trip”, “OC_Accel Trip” are all on the D0-bit
and the corresponding values are 0x01, 0x02, 0x08, “OvLd Alarm” is on the D9-bit and the corresponding value is
0x08. Then: D0 =0x01+0x02+0x08 = 0x0B, D9 = 0x08.So, "1 Drv_L" should be set to "0000000B", "3 Drv_H"
should be set to"00000080",press , key to select standby relay which need to be modified,press , key to
move the cursor to select the bit that need to be modified, and press “+”,“-” key to increase or decrease the size of
the data, then press “ESC” key and save the modification.
“Reset_L” indicates the mode of standby relay outputs reset. In the “Set output” interface,the six digits on
the right of“Reset_L” correspond to the reset mode of the six standby relay outputs respectively. From right to left,
they are D0-bit, D1-bit, D2-bit, D3-bit, D4-bit and D5-bit. D0-bit corresponds to the reset mode of standby relay
output 1, D2-bit corresponds to the reset mode of standby relay output 2, and so on. When one bit is set to “0”, it
indicates that the reset mode of the standby relay output is “instant mode”. That is when the corresponding
protection act, the standby relay contact act, and when the corresponding protection return, the standby relay
contact return automatically. When one bit is set to “1”, it indicates that the reset mode of the standby relay output
is “Manual mode”. That is when the corresponding protection act, the standby relay contact act, and when the
corresponding protection return, the standby relay contact don’t return until user press “RES” to reset the standby
relay output.
“OUTPUT_REVERT”: Six standby relay outputs revert to default configuration, when leaving factory, the six
standby relay outputs have been configured as “0”, and that is, the standby relay outputs
are not associated with each protection.
“DC-OUT_SET”: Entering the menu, we can select 4-20mA DC output channel (Current_ch n, n=1~4) and
calibrate the channel (Modify_ch n, n=1~4). If device does not need 4-20mA DC output
function, user can ignore this setting or set to "0".
35
WGB-611A Line protection device
Current_ch n: Display and change channel output object. Press“+”, “-” key to change output channel,
00 corresponds to no output (NO), the output type switch other values correspond to are displayed in
the lower right corner.
Modify_ch n: Display and change channel output value. Press“+”, “-” key to calibrate the size of the
data.
8.11 “VER” menu instruction
After entering the “VER” menu, we can check the device model, CRC check code, version of the program,
software updating time and factory number of the device.
36
WGB-611A Line protection device
Relay Description
Alarm signal Alarm relay outputs (n301, 302), “ALARM” indicator lamp lights up
Trip signal Tripping signal relay outputs (n301, 303), “TRIP” indicator lamp lights up
Close signal Closing signal relay outputs (n301, 304), “CLOSE” indicator lamp lights up
Tripping Tripping relay outputs (n315, 316)
Closing Closing relay outputs (n317, 318)
Remote control tripping relay outputs (After the correct connection of control
RC_tripping
loop, the device can trip off circuit breaker, we believe that the relay is normal)
The control
Remote controlcircuit wiring
closing relay correct,
outputs circuit
(Afterbreakers thatconnection
the correct can jump of
thecontrol
relay
RC_closing
normal)
loop, the device can close circuit breaker, we believe that the relay is normal)
Tripping Relay,Tripping signal relay exports; “TRIP” indicator lamp lights up
( The control circuit wiring correct, circuit breakers that can close the relay
Stdby relay 1 Standby relay 1 outputs (n312, 313, 314)
normal)
Stdby relay 2 Standby relay2 outputs (n416, 417)
37
WGB-611A Line protection device
CB open Abn Check the circuit breaker open position monitoring loop
12 Accessories
12.1 Documents supplied together with the product
a. One certificate of competency.
b. One instruction book with wiring elementary diagram.
c. One packing list.
12.2 Attachment supplied together with the product
Supply installation attachments according to the number predetermined by the device structure.
13 Ordering instruction
When ordering, please indicate:
38
WGB-611A Line protection device
39
WGB-611A Line protection device
14 Attached drawings
40
WGB-611A Line protection device
41
WGB-611A Line protection device
42
WGB-611A Line protection device
43
WGB-611A Line protection device
15 Appendix A (Menu)
15.1 Menu structure
4 TEST Used to test the device: calibrate analog,drive relay output and communication test.
44
WGB-611A Line protection device
45
WGB-611A Line protection device
46
WGB-611A Line protection device
47
WGB-611A Line protection device
48
WGB-611A Line protection device
49
WGB-611A Line protection device
50
WGB-611A Line protection device
15.2.2 RECs
The description of menu text in “ACTION_RECs” refer to section 15.2.4 of appendix A: TEST/
COMM_TEST/Action info.
(2) ALARM_RECs
51
WGB-611A Line protection device
52
WGB-611A Line protection device
15.2.3 SET
The description of menu text in “STRAP_SET” refer to section 15.2.1 of appendix A: VIEW/STRAP
STATUS.
(2) SETTING_SET
The description of menu text in “SETTING_SET” refer to section 15.2.1 of appendix A: VIEW/PROT
SETTING.
(3) SG_SWITCH
(4) SG_COPY
53
WGB-611A Line protection device
15.2.4 TEST
54
WGB-611A Line protection device
a. Action info
55
WGB-611A Line protection device
56
WGB-611A Line protection device
c. BI info
57
WGB-611A Line protection device
(4) PWD_SET
(5) PARM_SET
58
WGB-611A Line protection device
59
WGB-611A Line protection device
(9) DC-OUT_SET
60