Professional Documents
Culture Documents
Sis 2.0 5
Sis 2.0 5
SMCS - SENR10290006
Remove & Install Automatic Timing Advance 1272-010
PIP
-10
202 858
04: 2 /0 5 3 6
13: 30 3 /
SEN 45+
R 0
© 2 102 1:00
1. Remove nuts (1), cover (2), and the gasket.
0 2 2C 9
Cat
erp ater
Con illa pill
2. Put No. 1 piston at the top center compression position (TC) with the following procedure.
fide r: ar I
a. Remove plug (3), two bolts and cover (2) from the flywheel housing.
nc.
ntia
lG
ree
n
b. Install Tool (B) in the flywheel housing. Use Tool (B) to slowly rotate the engine in the direction of normal rotation,
(counterclockwise as seen from the flywheel end of the engine), until timing bolt (4) can be installed in the flywheel housing and
into the hole in the flywheel.
c. Remove the valve cover from the valve cover base. Check to see if both rocker arms (5) for the No. 1 cylinder can be moved
backward and forward.
NOTE: The No. 1 piston is at the top center compression position (TC) when the timing bolt is installed in the flywheel and both
rocker arms for the No. 1 cylinder can be moved backward and forward. If both rocker arms cannot be moved, the No. 1 piston is
not at the top center compression position (TC). Remove the timing bolt from the flywheel and rotate the engine in the direction
of normal rotation, (counterclockwise as seen from the flywheel end of the engine one full turn 360 degrees, and install the
timing bolt again.
3. Remove the timing bolt, and use Tool (B) to rotate the engine in the opposite direction of normal rotation (clockwise as seen
from the flywheel end of the engine) a minimum of 30 degrees .
PIP
-10
NOTE: The timing is correct if Tool (A) and the timing bolt can be installed at the same time. The timing procedure in Systems
202 858
Operation, Testing & Adjustment Manual must be done again if the time bolt and Tool (A) can not be installed at the same time.
2 5
4. Remove the plug from the timing pin hole in the fuel injection pump housing. Install Tool (A) in the fuel injection pump housing
04: /0 3 6
as shown. Slowly rotate the crankshaft counterclockwise (as seen from the flywheel end of the engine) until Tool (A) goes into the
3 /3
slot in the fuel pump camshaft.
13: 0
SEN 45+
NOTICE
R 0
© 2 102 1:00
Too much pressure on the timing pin can damage the fuel
injection pump or the timing pin.
0 2 2C 9
Cat
5. Put the timing bolt in the timing hole in the flywheel housing. Rotate the crankshaft counterclockwise (as seen from the flywheel
erp ater
end of the engine) until the fuel pump camshaft is tight against Tool (A). This removes gear clearance from the drive train. If the
bolt can be installed in the timing hole in the flywheel, the timing of the fuel injection is correct.
n
7. Remove gear (9) from fuel injection pump camshaft (8).
9. Install two 3/8 in-16 NC x 6 in (152.4 mm) long guide bolts(10). Space the guide bolts evenly.
NOTICE
PIP
There is a light spring located beneath the flyweight cover (12).
-10
Hold cover (12) while removing last nut (11). Slowly remove
202 858
flyweight cover (12) to avoid dropping the spring.
04: 2 /0 5 3 6
13: 30 3
10. Remove four nuts (11) and remove flyweight cover (12).
/
SEN 45+
R 0
© 2 102 1:00
0 9
11. Put automatic timing advance (13) in position on the fuel injection pump camshaft, and install four bolts (14). Tighten bolts
Cat 2
(14) just past finger tight. Remove guide bolts (10).
2C
erp ater
Con illa pill
fide r: ar I
nc.
ntia
12. Install four nuts (11) standard torque. Install Tool (C).
lG
ree
n
al G
ree
n
NOTICE
14. Install all mounting bolts (14) and tighten to a torque of 3 N·m (27 lb in).
15. Loosen knurled nuts (17). Removed four nuts (16) and remove Tool (C).
16. Install spring and flyweight cover (12). Install four nuts (11).
PIP
-10
202 858
2 / 5 3
17. Install a gasket and timing advance cover (2). Tighten eight nuts (1) to standard torque.
04: 0 6
13: 30 3 /
SEN 45+
R 0
© 2 102 1:00
18. Remove Tool (A) and replace the plug in the fuel pump housing.
0 2 2C 9
Cat
erp ater
Con illa pill
fi r: ar
Cat 22 C
erp ater
Con illa pill
fide r: ar I
nc.
ntia
lG
ree
19. Remove the timing bolt and replace plug (3). Install cover (2) on the flywheel housing.
n
20. Check the dynamic timing curve. See the Systems Operation Testing & Adjusting Manual for the proper specifications.
Start By:
1. Remove four nuts (1) and remove cover (2) from the automatic timing advance.
3. Remove four cap screws (5), two retainer plates (6) and remove carrier (7) from automatic timing advance.
PIP
-10
4. Remove snap ring (8), tapered race (9), spool (10) and weights (11) from the carrier (7).
202 858
04: 2 /0 53 6
13: 30 3 /
SEN 45+
5. Remove race (12) from carrier (7).
R 01:
04: 03/3
13: 0
SEN 45+
R 0
© 2 102 1:00
0 2 2C 9
Cat
6. Remove four bolts (13).
erp ater
Con illa pill
fide r: ar I
nc.
ntia
lG
7. Remove plate (14), ring (16) and ring (17) from carrier assembly (15). Remove seals (19) and (20) from carrier assembly (15).
Remove seal (18) from plate (14).
ree
Assemble Automatic Timing Advance 1272-016
n
2. Lubricate seal (18), (19) and (20) with engine oil then carefully install carrier assembly (15) into ring (17). Install ring (16) and
plate (14).
PIP
-10
2 8
PIP
-10
202 858
04: 2 /0 5 3 6
13: 30 3 /
5. Position weights (11), spool (10), tapered race (9) and snap ring (8) into carrier (7).
SEN 45+
R 0
© 2 102 1:00
0 2 2C 9
Cat
6. Lubricate spool (10) and lower it into position in the automatic timing advance. Position retainer plates (6) and install four cap
erp ater
screws (5). Tighten cap screws (5) to a torque of 3.4 ± 0.4 N·m (30 ± 4 lb in).
End By:
1DL1-UP, 2KR1-UP, 2SR1-UP, 2XS1-UP, 2YR1-UP, 3RR1-UP, 4SK1-UP, 4SN1-UP, 5EW1-UP, 5GR1-UP, 5JK1-UP, 5SG480-UP, 5ZS1-UP,
6BK1-UP, 6RN1-UP, 7FS1-UP, 7LN1-UP, 7XM1-UP, 8PL1-UP, 9CM1-UP, 9EM1-UP, 9LR1-UP, BXL1-UP, MEJ1-UP, RJM1-UP, T5X1-UP
PIP-10858536
2022/03/30
04:11:51+01:00
SENR10290006
© 2022 Caterpillar Inc.
Caterpillar:
Confidential Green