Professional Documents
Culture Documents
Data Sheet
Compression hardness 3 0.71 N/mm2 EN ISO 844 1 at 10 % linear compression, 3rd load cycle
2 1
Compression set <5% EN ISO 1856 50 % deformation, 23 °C, 72 h, 30 min after removal of load
Dynamic modulus of elasticity 3 7.54 N/mm2 DIN 53513 1 at specific load of 0.75 N/mm2, 10 Hz
2 1
Static shear modulus 0.69 N/mm DIN ISO 1827 at a pretension of 0.75 N/mm2
Dynamic shear modulus 1.02 N/mm2 DIN ISO 1827 1 at a pretension of 0.75 N/mm2, 10 Hz
2 1
Min. tensile stress at rupture 3.90 N/mm EN ISO 527-3/5/500
1
Measurement / evaluation in accordance All information and data is based on our current knowledge. The data can be applied
with the relevant standard for calculations and as guidelines, are subject to typical manufacturing tolerances
2
The measurement is performed on a and are not guaranteed. Material properties as well as their tolerances can vary de-
density-dependent basis with differing pending on type of application or use and are available from Getzner on request.
3
test parameters
Further information can be found in VDI Guideline 2062
www.getzner.com
Values apply to shape factor q = 3
(Association of German Engineers) as well as in glossary.
Further characteristic values on request.
1
Sylodyn ® NE
1.5
Quasi-static load deflection curve
12.5 mm 25 mm 37.5 mm
measured with a loading rate of
0.075 N/mm2/s.
1.2
50 mm
Shape factor q = 3
0
0 1 2 3 4 5 6 7 8 9 10
Deflection in mm
Modulus of elasticity
15
0.75 N/mm2
Quasi-static modulus of elasticity as
tangential modulus from the load
12 deflection curve. Dynamic modulus
of elasticity from sinusoidal excita-
tion with a velocity level of 100 dBv
9 re. 5 · 10-8 m/s corresponding to a
30 Hz
10 Hz
vibration amplitude of 0.22 mm at
10 Hz and 0.08 mm at 30 Hz.
Quasi-static
6
Parameter: frequency
0 Shape factor q = 3
0 0.3 0.6 0.9 1.2 1.5
Specific load in N/mm2
www.getzner.com
2
Natural frequency
Specific load in N/mm2
1.5
Natural frequencies of a vibratory
system with a single degree of free-
dome, consisting of a mass and an
1.2
elastic bearing made of Sylodyn® NE
on a rigid surface.
0.9
Parameter: thickness of
0.3
50 mm
0
5 10 15 20 25
Natural frequency of the system in Hz
100
Reduction of the transmitted me-
90 chanical vibrations by implementa-
-40 dB/99 %
-35 dB/98 % tion of an elastic bearing consist-
80 -30 dB/97 % ing of Sylodyn® NE based on a stiff
-25 dB/94 %
70 subgrade.
-20 dB/90 %
60 Parameter: factor of transmission
-15 dB/82 % in dB, isolation rate in %
50
-10 dB/69 %
40
-5 dB/44 %
30 0 dB/0 %
20
10
0
5 10 15 20 25
Natural frequency of the system in Hz
www.getzner.com
3
Influence of the shape factor
The graphs show the material properties at different shape factors.
Static range of use in N/mm2
Change in deflection
0.90 150 %
120 %
0.75
90 %
0.60
60 %
0.45
30 %
0.30
0%
0.15 -30 %
0.3 1 3 6 0.3 1 3 6
Shape factor Shape factor
Fig. 5: Static range of use in relation to the shape factor Fig. 6: Deflection 4 at constant thickness in relation to
the shape factor
Change in dynamic modulus of elasticity
20 % 10 %
0% 0%
-20 % -10 %
-40 % -20 %
-60 % -30 %
DB Sylodyn NE en © Copyright by Getzner Werkstoffe GmbH l 03-2022
-80 % -40 %
0.3 1 3 6 0.3 1 3 6
Shape factor Shape factor
4
Reference values: specific load 0.75 N/mm2, shape factor q = 3
Material properties can be determined using the online calculation program FreqCalc.
The program can be accessed via www.getzner.com (registration necessary).
AUSTRIA — Bürs GERMANY — Berlin — Munich — Stuttgart FRANCE — Paris — Lyon JAPAN — Tokyo INDIA — Pune
JORDAN — Amman CHINA — Beijing USA — Charlotte AUSTRALIA — Melbourne www.getzner.com
4