Beto (o> e Rottig
Hardtop XP
Product description
‘This Is @ two component chemically curing allphatic acrylic polyurethane coating. It has a glossy finish with very
{900d gloss retention. Its 3 high solids product. The product has good application properties with low dry spray.
‘To be used as Lapcoat in atmospheric environments.
Typical use
Marine:
Recommended for topside, deck and superstructure.
Protective
Recommended for offshore environments, refineries, power slants, bridges and buildings. Suitable fora wide
range of Industral structures. Used as a topcoat in pre-qualified NORSOK systems,
Approvals and certificates
‘This product contributes to the Green Buildings Standard credits. Please see section Green Building Standards.
NORSOK System 1, Rev.5
Grain, Neweastle Occupational Health
Food, Comaliant with USA, FDA Title 21, Part 175,300 for dry solids
When used as part of an approved scheme, this material has the following cetincation:
= Low Flame Spread In accordance with EU Directive for Marine Ecuipment. Approved in accoréance with parts 5
and 2 of Annex 1 of IMO 2010 FTP Code, or Parts 5 and 2 of Annex 1 of IMO FTPC whan in compliance with
IMO 2010 FTP Code Ch. 8
Consult your Jotun representative for details
‘Adcitional certificates and approvals may be available on request.
Other variants available
Hardtop xe Aly
Hardtop XL
Hardtop XPF (Winter grade version)
Refer ta separate TDS for each variant.
Colours
‘according to colour card and Mulvcolor Industry tinting system (MCI)
Product data
Property Test/Standard Description
Solids by volume 1503233 342%
Goss level (GU 60 °) 1s0 2813 ‘loss (70-85)
Flash point 150 3679 Method 1 30°C
Density caleuiated 14 kal
VOC-US/Hong Kong US EPA method 24 (tested) 323 gf
(CARB{SCM)2007, SCAQMD rule 1223, Hong Keng)
‘ate of sue: 22 March 2021, Pages 1/5
‘This Technical Oata Sheet supersedes those previously issued
“The Techical Data Sheet (TDS) is recommended to be readin conjunction withthe Safety Data Sheet (SOS) and the
ppcation Guide (AG) fo the product. For your Nebrest lea tun ole please vis 9ur website ot wi JotuncamTechnical Data Sheet 4 JOTUN
Hardtop XP
voc-eu 10 (2019/75/EU) (theoretical) 326 0/1
\voc-china GByT 23985-2009 (testee) 330 9/1
voc-Korea Korea Clean Arr Conservation Aet (tested) 385 9/1
(Wax. thinning ratio incleded)
“The provided cata is typical for fa
All datas valid for mixed paint
Gloss description: According to Jotun Performance Coatings’ definition.
FY produced products, subject to slight variation depending on colour
‘The VOC values refer to white colour.
m thickness per coat
‘Typical recommended specification range
Dy film thickness so - 100 ym
‘Wet fl thickness 80 - 160 um
Theoratical spreading rate «12.6 - 6.3. m/l
Bright colours may need film thickness inthe high end of the recommended specification range te achieve
opacty.
Special effect colours may have diverging specification range. Refer to the Application Gulde (AG) for addtional
Information of contact your nearest Jotun offi,
Surface preparation
‘To secure lasting adhesion to the subsequent produc all surfaces shall be clean, dry and free from any
Surface preparation summary table
Surface preparation
substrate Minimum Recommended
Coated suraces lean, ry and uncamaged compatible Cleen, dry and unéamaved compatible
oath ete
Application
Application methods
‘The product can be apaled by
Spray: Use alr spray or airless spray
Brush: Recommended for stripe coating and small areas. Care must be taken to achieve the
specified ary fm thickness
Rotter: May be used. Care must be taken to achieve the specified dry film thickness.
Date of esue: 22 March 2021 Page: 2/8
This Technical Oata Sheet supersedes those previously issued
“The Techical Data Sheet (TDS) is recommended to be readin conjunction withthe Safety Data Sheet (SOS) and the
‘apication Gude (AG) fr this produc. For your nebrest eal Jotun office, pleese visi our weit st worn Jotun. comTechnical Data Sheet 4 JOTUN
Hardtop XP
Product mixing ratio (by volume)
Hardtop XP Comp A 10 parts)
Haratop XP Comp B 1 partis)
Thinner/Cleaning solvent
Thinner: Jotun Thinner No, 10 /Jotun Thinner No, 26
Jotun Thinner No, 26 is supplied and used in USA due to legisation.
‘Thinning is not normally required. Consult the local representative for advice during application in extreme
conaltions. Do nat thin more than allowed by local environmental leaisation.
Gui
Nozzle tip (ineh/1000): 13.19
Pressure at nozzle (minimum) 150 bar/2100 pst
Guiding data for air spray
Nozzle tp HVLP: 11-19 (Inch/1000) / Pressure pot: 1.1-1.9 (mm)
Pressure at nozzle (minimum) HVLP: 2.1 bar/30 psi / Pressure pot: 2.1 bar/30 pst
Drying and Curing time
‘Substrate temperature sc 10°C 23°C 40°C
Surface (touch) éry anh 6h SH 2H
Walleon-ary 2h ih 7h 4h
Dry to over coat, minimum 2h sh 7h ah
Dried/cured for service 21d 146 76 3d
For maximum overco
ting intervals, reer to the Application Gulde (AG) for this product.
Drying and curing times are determined under controlled temperatures anc relative humidity below 85 %, and
‘at average of the OFT range forthe product.
Surface (touch) dry: The state of drying when slignt pressure with 2 finger does not leave an Imprint or reveal
tackiness.
Walk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks,
Inmpries or other physical damage
Dry to ever coat, minimum: The recommended shortest time before the next coat can be applied
Dried/cured for service: Minimum time before the coating can be permanently exposed to the Intended
‘environment/medium.
Date of esue: 22 March 2021 Page: 3/8
This Technical Oata Sheet supersedes those previously issued
“The Techical Data Sheet (TDS) is recommended to be readin conjunction withthe Safety Data Sheet (SOS) and the
‘apication Gude (AG) fr this produc. For your nebrest eal Jotun office, pleese visi our weit st worn Jotun. comTechnical Data Sheet 4 JOTUN
Hardtop XP
Induction time and Pot life
Paint temperature zaec 40%c
Pot life 15h SOmin
Heat resistance
‘Temperature
Continuous Peak
Ory, atmospheric 320°C 140 °C
Peak temperature duration max, 1 hour.
The temperatures listed relate to retention of protective properties, Aesthetic properties may suffer at these
temperatures.
Product compatibility
Depending on the actual exposure ofthe coating system, various primers and topcoats can be used in
combination with this product. Some examples are shown below. Contact Jotun for specific system
recommendation.
Previous coat: epoxy, zinc epoxy, epoxy mastc, polyurethane
Packaging (typical)
Volume Size of containers
(litres) (litres)
Hardtop xP Comp A 455/182 5/20
Haratop xP Comp B 0.45/18 1/3
‘The volume stated is for factory made colours, Note that local variants in pack size and filed volumes can vary
due te local regulations.
Storage
The product must be stored in accordance with national regulations. Keep the containers ina dry, cool, well
ventlates space and away from sources of hest and ignition, Containers must be kept tightly closed. Handle
with care
Shelf life at 23 °C
Hardtop XP Comp A 48 month(s)
Hardtop XP Comp B 48 month(s)
In some markets commercial shelf Ife can be dictated shorter by local legislation. The above is minimum shelf
Me, thereafter the paint quality fs subject to re-inspection,
Date of esue: 22 March 2021 age: 4/6
This Technical Oata Sheet supersedes those previously issued
“The Techical Data Sheet (TDS) is recommended to be readin conjunction withthe Safety Data Sheet (SOS) and the
‘apication Gude (AG) fr this produc. For your nebrest eal Jotun office, pleese visi our weit st worn Jotun. comTechnical Data Sheet 4 JOTUN
Hardtop XP dean otc Popery
Green Building Standards
‘This product contributes to Green Building Standard credits by meeting the following specific requirements:
LeeD@v4 (2013)
MR credit: Building product disclosure and optimization
= Material ingredients, Option 2: Material Ingrecient Optimization, International Alternative Compliance Path ~
REACH optimization: Fully inventoried chemical Ingredients to 100 ppm and not containing substances on the
REACH Authorization Ist ~ Annex XIV, the Restriction lst ~ Annex XVII and the SVHC candidate list
~ Environmental Product Declarations. Praduct-speciic Type Ii] EPD (ISO 14025)21930, EN 15804).
BREEAM® International (2018)
Mat OL: Product-specific Type IIT EPD (ISO 14025;21930, EN 15804).
BREEAM® International (2013)
Hea 02: VOC content for Twe-pack performance Coatings SB (S00 gj!) (EU Directive 2004/42/5).
The EPDs are available at www.epd-norge.no
Caution
‘This product Is for professional use only. The applicators and operators shall be trained, experienced and have
the capablity and equipment te mi/stir and apply the coatings correctly and according to Jotun's technical
documentation. Applicators and operators shall use appropriate personal protection equipment when using this
product. This guideline is given based on the current knowledge of the product. Any suggested deviation to sult
the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing
the work
Health and safety
Please observe the precautionary notices splayed on the container. Use under well ventilated conditions. D9
not inhale spray mist. Avoid skin contact. Spillage on the skin should immediately be removed with sutable
Cleanser, soap and water. Eyes should be well shed with water and medical attention sought Immediately
Colour variation
When applicable, products primarily meant for use as primers or antfoulings may have sight colour variations
‘rom baten to batch. Such products and epoxy dased products Used as @ finish coat may chalk when exposed to
sunlight and weathering
Colour and gloss retention on_topcoats/finish coats may vary depending on type of colour, exposure
‘environment such as temperature, UV intensity et, application quality and generic type of paint. Contact your
Tocal Jotun office for further information,
Disclaimer
Date of esue: 22 March 2021 Page: 5/8
This Technical Oata Sheet supersedes those previously issued
“The Techical Data Sheet (TDS) is recommended to be readin conjunction withthe Safety Data Sheet (SOS) and the
‘apication Gude (AG) fr this produc. For your nebrest eal Jotun office, pleese visi our weit st worn Jotun. comTechnical Data Sheet 4 JOTUN
Hardtop XP dean otc Popery
The Information In this dacument is given to the best of Jotun’s knowledge, based on laboratory testing ane
practical experience, Jotun's products are considered as semi-finished goods and as such, products are often
Used under conditions beyond Jetun's control. Jotun cannot guarantee anything but the cualty ofthe product
self. Minor product variations may be implemented in order to comply with local requirements, Jotun reserves
the right to change the given data without further notice.
Users snould always consult Jotun for spectic uicance on the general sutabilty ofthis product for their neds
‘anc specifc application practices,
I there is any inconsistency between cifferent language issues of this document, the English (United Kingdom)
version will preva
Date of esue: 22 March 2021 Page: 6/8
This Technical Oata Sheet supersedes those previously issued
“The Techical Data Sheet (TDS) is recommended to be readin conjunction withthe Safety Data Sheet (SOS) and the
‘apication Gude (AG) fr this produc. For your nebrest eal Jotun office, pleese visi our weit st worn Jotun. com