Professional Documents
Culture Documents
FH CX65 - MHC C605 - HCD H605
FH CX65 - MHC C605 - HCD H605
(éront side play)
(top)
eer (ast eltward/iast
rightward)
FARE A/B butions
[B]SVSTEM POWER switch
[B)VOL (+/-) buttonsSECTION 3
DISASSEMBLY
Note : Follow the disassembly procedure in the numerical order given,
3-1. CD MECHANISM REMOVAL
@ (Mechanism
(COM33B-58D19)
BS | @cn1818 19pin)
@ Five screws (BVTP3x10)
“our screws. xe | ere S
Orarsemnanmen P<
Pe a -S
SPE, eee —
oh ts }CN1502 is
a (pin) eee
ee :
@ Beck pane! (Upper)SECTION 4
GEAR ALIGNMENT
Note : Align numbered items inthe figure inthe order of the numbers.
4-1, GEAR (CAM B), LEVER (R), ASSEMBLY INSTALLATION (R SIDE)
1, Align so that the slider assembly hole @ ( $3) overlays the
sub-chassis (B) assembly ( 2) hole.
2, Install so thatthe gear (joint) ® hole overlays the the sub-chassis(B)
assembly side hole
3. Align the gear (Cam B) © hole and the sub-chassis (B) assembly side
‘© hole and install in such a way that the shaft of © fits into the groove
in the gear (Cam B). (For the gear postions, see Figure 1.)
Note : Check tha the gear (Cam B) and gear Goint) mesh as at ©.
@ Gear goin)
Gear (Cam B)
Pulleys (UD)
‘Sub-chassis (B) Assy
"© @ Stopper washer
@ Gear (cam 8)
SY Stopper washr
@ Lover (ny assy
4-2, GEAR (CAM B), LEVER (L) ASSEMBLY INSTALLATION (L SIDE)
1. Align so that the sider assembly ole D (¢ 3 overlays the sub-chasis(B) (Fin.2) ©
assembly (6 2 hole
2. Install so thatthe gear int) @ hole overlays the the sub-chasis(B) assembly side
hole.
3. Align the gear (Cam B) © hole andthe sub-chasis(B) assembly side © hole and
install in sucha way that the shaft of © fits int the groove inthe gear (Cam B).
(Forte gear postions, see Fig. 2)
[Note : Check thatthe gear (Cam B) and gear (joint) mesh as at ©.
‘Sub-chassis (B) Assy
@ Gear Goin)
SP
© coar(cam ——
@ stopper nash
fe ae
O Sider Assy
°@ Lover (Ly Assy4-3, GEAR (U/D) INSTALLATION (R SIDE)
Goar (Cam 8)
(Fig. 1) Pulley (UD)
overlays the gear (U/D) side ® hole.
(Por the gear positions, see Fig. 1.)
Note : Check thatthe gears are meshing as at ©
@l 1. Check thatthe hole @ in the gear (Cam B) and the hole in
~ sub-chassis (B) assembly mesh,
7 2: Instal the gear (UD) $0 that he slider assembly side @ hole
@ Stopper washer
4-4. GEAR (U/D) INSTALLATION (L SIDE)
‘Sub-chassis (8) Assy
®
1. Check that the hole @ in the gear (Cam B) and the hole in
sub-chassisB)asembly mes, Ne
2. Install the gear (U/D) so that the slider assembly side @ hole
coverays the gear (UID) side @ hole
(Gor the gear postions, see Fig.) @ cea u0)
Note : Check that the gears are meshing as at ©).
© Stopper washer
ange4-5. GROOVE CAM (R) INSTALLATION (R SIDE)
1. Install the groove cam (R) so thatthe groove cam (R) side @hole and
‘gear (U/D) side @ hole ae aligned at their centers. (See Fig. 1.)
@ Groove cam (A)
@ stopper washer
4-8. GROOVE CAM (L) INSTALLATION (L SIDE)
1 Install the groove cam (L) 50 that the groove cam (L) side ® hole and
‘ear (UD) side @ hole are aligned at their centers. (See Fig. 2.)
‘Sub-chassis (B) Assy
‘Groove cam (1)
@ stopper washer Center
aaySECTION 5
ADJUSTMENTS
5-1, MECHANICAL ADJUSTMENTS
PRECAUTION
1, Clean the following parts with a denatured-alcohot-
moistened swab
recordiplayback head pinch roller
erage head rubber belts
capstan idlers
2, Demagnetize the record/playback head with a head
demagnetizer,
3, Do not use a magnetized screwdriver forthe adjustments
4. After the adjustments, apply suitable locking compound
to the part adjusted
5. The adjustments should be performed with the rated
power supply voltage unless otherwise noted
5-2. ELECTRICAL ADJUSTMENTS
DECK SECTION
“The adjustment should be performed in the publication.
(Be sure to make playback adjustment at first)
2. The adjustment and measurement should be performed for
both L-CH and R-CH.
© Switch position
DOLBY NR switch : OFF
FUNCTION button : CD
3. Deck section electrical adjustments are made in test mode by
pressing TUNER/BAND, DISPLAY, and POPS at the same
4. Input point and output level measurement point.
Output lev
— measurement Input point
# Torque Measurement siemy(-2ase prose
Mode | Torque Meter Meter Reading oa (Bt oe SS Ke)
3610 61g setae
ce (050 08h) ton me P Poort
Forward ie Seem wor | gered
Back Tension] CO-020 (0.028 O83 caine) Ve
3610 ota B
Renmei (050 08toxret) 7
Reem MAINBOARD
Roveoe Zio Germ
Back Tein] C22RC | 002s" dRs seinem ow
ae ae che lagen
ae ae (085° sine)
1 Tape Tension Measurement Contents tee
Toate, — 1 | Wend simu Adee
iede [Tension Meter Water Reading nae — ee
Forward [CQO ore than He 05.260) Ells, 068 | Tape Speed Aajuinent
Rene cose roe ane G8 260),
SaB=OTV
Record/Playback Head Azimuth Adjustment
Procedure :
1, Forward Playback mode
Reverse Playback mode
(raise, roan) —_
f PET
aap2. Tum the adjustment serew for the maximum output levels.f
these levels do not match,tum the adjustment serew until both
>| ° Lee
©EQE8Y
[ee oe
4, Change the review playback mode and repeat the steps | to 3.
5, After the adjustment, lock the adjustment serew with suitable
locking compound.
‘Adjustment Location
~ recordiplayback head (Deck A and B)
Tape Speed Adjustment [DEGKA] [DECKE
Procedure:
Peron high spect adisinet before nomml spend a
Made: Payback
eae
az,
cergarignmms
Speed Beck | Aalniment | Prauenaycouner
a ee
wet Ff FST cn a
* Continue to press HIGH SPEED DUBBING switeh ($551) in
playback mode : High speed playback.
Frequency difference between the begining and the end of the
tape should be within + 39%.
Frequency difference between deck A and deck B the biginning.
‘ofthe tape should be within 1.5%.
‘Adjustment Location : AUDIO boa.
(Gee page 14)
DECK A] [DECK 6)
Playback Level Adjustment
Procedure :
Mode : Playback
‘sian 006)
i
Deck A is RV3II(LCH) and RV411(R-CH), deck B is RV301
(L-CH) and RV401 (RCH) 50 that adjustment within adjustment
level as follows.
+ A
Sea
pute peasueen’ po
erp
Adjustment Level :
LINE OUT level: ~ 7.5 + 0.54B (0.31 10 0.35V)
Level Difference between Channels : within 0.5¢B
Confirm the DOLBY OUT level does not change in playback mode
‘while changing the mode from playback to stop several times.
Adjustment Location : AUDIO board
(see page 14)
aiRecord Bias Adjustment [DECK 6. ‘Adjustment Level :
Procedure : DOLBY OUT level : ~ 234B + 0.54B (51.8 to 58.1mV)
1. Record mode
‘Adjustment Location : MAIN board
aire } etane 20538
ut pt (oe page 12)
‘Adjustment Location :
vaot : Payback evel (Dok LH
veo: Payosck Love!
ororo Rom
ae
ce
2. Playback mode
4
vee: Recor (7.08
b
‘vse cord Bae (ch
aves: Tape speot
oon
@D Prvsrs rapes tet
(oars oH
peck
pin pennant rot
ava: Playack Lovet
3. Confirm playback the signal recorded in step 1 become (MAINBOARD) ~ Component side —
adjustment level as follows.
(occa n-cn)
4. If these levels do not adjustment level, adjustment the RV341
(L-CH) and RV441 (R-CH) to repeat step 1 and 4,
Adjustmegt level : Playback output of 31SHz to playback output
of 1OkHz : ~ 0.SdB to 0.54B.
(= 130 13mV)
Adjustment Location : AUDIO board.
Record Level Adjustment [DECK B]
1— Avast sRacrs tov)
| vers Racor teriey
FUNCTION button : CD
Procedure :
1. Record mode
stan san (- 20809 age
Qa
eo = HE
put pat (ee page 12)
2. Playback mode
pre
eben del
3, Confirm playback the signal recorded in step become
adjustment level as follows.
4. If these levels do not adjustment level, adjustment the
RV401(L-CH) and RV4S1 (R-CH) to repeat step 1 and 4.
ag[TUNER SECTION]
Note. 1 : The adjustment should be performed inthe publication.
(AM-> FM+SW)
Note. 2: As a front-end (FE1) is dificult to repair if faulty, replace
itwith new one,
‘AM Section Adjustment
FM Section Adjustment
Setting :
PURE sa)
— uueena tees
ZN 750 com i
AM Tuned Indication Lighting Level Adjustment
Band : MW
Procedu
1, Set loop antenna A so that the loop antenna B input level
becomes 3.2mV (708B 4)
2. Tune the set to 999kH2.
3. Adjust RV4I so that the [TUNED] light up.
4. Confirm that the [TUNED] light off with AM RF Signal
generator output level set at OB ys.
Confirm the FM tuned indication lighting level and adjust if
necessary.
Adjustment Location : Main board
[MAIN BOARD) — Component side —
‘T6101 spear Tama! —f
(7:50 Tracing Aeutrant —]
vA :AM Tune inten Lip Lev
‘vines
a
FM Tuned Indication Lighting Level Adjustment
Band: FM.
Procedure :
1, Supply @ 11.2uV (214Bu1) 98MHEz signal to the ANTENNA
terminal (TM1).
2. ‘Tune the set to 98MHz.
3. Adjust RV42 so that the [TUNED] tight up.
4. Confirm that the [TUNED] light off with FM RF signal
‘Benerator output level set at 164B
‘Adjustment Location : Main board
‘SW OSC Voltage Adjustment
Band: SW
(E3, Saudi Arabia, Malaysia, Singapore mode!)
Procedure:
‘Connecet the VOM to JW376 (OSC)
‘Tune the set to 5.95MHz.
Adjust T2 for 1.0 to 1.1V reading on the VOM.
‘Tune the set to 17 90MH2.
Adjust CV2 for 8.4 to 8.6V reading on the VOM.
‘SW Tracking Adjustment
Band: SW
Procedure:
1. Connect the VOM to speaker terminal (TBIO1).
2. Adjust for a maximum reading on VOM,
‘Signal generator and on
‘sat frequency. ee
70MHZ Ti
170 MHZ evi
Adjustment Location : Main board
{11 ssw Tracing Agusment
| ave Fred nent Ugg Lave!
‘hiner!
"2 5W 050 Vetage Aausinart
i: sw 080 VotageAgustnent
ip[ed SECTION]
Note
1, CD Block basically constructed to operate without adjust-
ment, Therefore, check each item in order given.
2. Use YEDS-18 disc (3-702-101-01) unless otherwise indi-
cated.
3. Use the oscilloscope with more than 10M @ impedance.
4. Clean an object lens by an applicator with neutral detergent
when the signal level is low than specified value with the
following checks.
Focus Blas Adjustment
This adjustment is to be done when the optical block is replaced,
‘Adjustment procedure :
1. Connect oscilloscope to test point TP (VC) and TP (RF) on
BD boa.
‘Tumed power switch ON. (Stop mode)
Put dise (YEDS-18) in and press the Pe button.
Press the DISPLAY/ENTER button. (Tracking servo ON)
‘Adjust RVIO1 so thatthe oscilloscope waveform is as shown
in the figure below (eye patter).
‘A good eye pattem means that the diamond shape (©) in the
center of the waveform can be clearly distinguished.
6. Release test mode after adjustment is completed.
(© RF signal reference waveform (eye pattern)
\ EXP. | 828
AMAA
EE
OO)
‘When observing the eye pattem, set the oscilloscope for AC.
range and raise vertical sensitivity.
s-cuv check
=
rm
trocar:
1. Connect oscilloscope to test point TP (FEO) and BD board.
2, Connect between test point TP (FOK) and GND by lead wire.
3. Tumed Power switch on,
4, Put dise (YEDS-18) in and tumed Power switch on again and
actuate the focus search, (actuate the focus search when dise
table is moving in and out.)
'. Check the oscilloscope waveform (S-curve) is symmetrical
between A and B. And confirm peak to peak level within
38+ 1.1Vpp.
‘S-curve waveform
~ \ wine 38 1.1¥Ep
6. fier check, remove the lead wire connected in step 2
Note : @ Try to measure several times to make sure thatthe ratio of
A: BorB: Ais more than 10:7.
'@ Take sweep time as long as possible and light up the
brightness to obtain best waveform.
RF Level Check
Teme 12
ewe,
Procedure :
1. Connect oscilloscope to test point TP (RF) on BD board.
2, Tumed Power switch on
3. Put dise (YEDS-18) in and playback.
4. Confirm that oscilloscope waveform is clear and check RF
signal level is correct o¢ not.
Note:
Clear RF signal waveform means that the shape “ ©" can be
clearly distinguished at the center of the waveform.
RAE BS
PF sal wavetor
PaO
A
WHA hh
WHR
WW
E-F Balance Check
te
ID]
pe tal
Procedure :
Ground main board IC101 pin @ with the lead wire.
Connect oscilloscope to test point TP (TEO) on BD board,
‘Tamed Power switch on.
Put disc (YEDS-18) in and playback.
Confirm that the osilloscope waveform is symmetrical on the
top and bottom in relation to OV, and check ths level
eeTraverse waveform
Doel 20 + 100m
6. Remove the lead wire connected in step 1
Focus/Tracking Gain (RV102/RV103)
‘This gain has a margin, so even if itis slightly off, There is no
problem.
‘Therefore, do not perform, this adjustment.
ease note that it should be fixed to mechanical center position
‘when you moved and do not know original postion.
‘Adjustment Location
[BD BOARD] — Component side ~
cigSECTION 6
EXPLANATION OF IC TERMINALS
Ic1o1_ TMP87CP64F-6269 (MAIN BOARD)
8 BACK UP 1_| Back up terminal.
i aremtarar [Re Or
|e ae}
a [ae ore | 6 | at ee a
26 SCOR (DSP) I__| Sub-code syne SO+SI detection input from DSP. (CXD2507AQ)
Seen on
a
3 [maser [of aoe to oe
18 —Pin No. Pinname vo Description
6 REQMG (© | Data transmission request output to system contol
a CLKMG ‘© | Clock output for communications with system contol
5 D.GM 1_| Serial data input form system control
6 DMG (O_| Serial data output to system contol
a RDY 1/0_| System control Ready signal inpuvouiput,_“L" ; READY
& VAREP =| Power suppiy. @5V)
eo VASS, =_[ xd
30) Ves = [end
3 Veo =__| Power supply @5¥)
32 URGENT. SIG T_[ Notused. @5¥)
33 | URGENT. STBY [| Notused. (OPEN)
34 BUG YIN = _| Not used. (GND Connected)
35 ADJUSTOR =_| Notused. CH" EVEL)
56 “ADIUST2 =| Net used. A” LEVEL)
a MAGICSPEED | —__| Notused. CH LEVEL)
8 ‘SPEC =| Notused: CH LEVEL)
3 DIST, = [ Rotused: CH” LEVEL)
o SPEED =_| Notused. CH" LEVEL)
or BREAK =| Net used." LEVEL)
@ BPLAY T_| Deck'B PLAY Switch inpat__“H" PLAY.
3 BSHUT T_| Deck Reel table signal input
4 BHALF 1 _| Deck'B Recond prevention claw A, B detection input
S ASHUT T_| Deck-A Reel table signal input
6 APLAY T_| Deck-A PLAY Switch input. “H": PLAY.
Gl ACHALF T_| Deck: HALF SW input
& CAPM HIL O_| Notused. (OPEN)
@ CAPMONIOFF | O__| Notused. (OPEN)
70 TRIG HAL o
7 BIRG O_| } Trigger motor contro output terminal.
7 ATRG o
B RELAY (0 _| Control output to RECIPR select switch, (10602)
74 AB (0 | Dolby ICPB input Deck AB select output. “L": A, "= B
75 NORMIHIGH (0 | BQ Select switeh output for nommal/high speed. “H" = High speed
6 BIAS ONOFF (© _| BIAS Oscillation ON/OFF control "H" ON.
7 RM ON/OFF © _[ REC Mute output “L* MUTE.
7% RECIPE © _[ DOLBYICRECIPLAY Select output “H": REC
a NR (© _| DOLBY ON/OFF Control output. “H”= ON.
0 LM (O_ [LINE Mute output “L": MUTE,
3 PASS (O_| PASS Amplifier switch output te DOLBY IC. (C401)
2 (CDG. MUTE =| Not used. (OPEN)
3 UP MOTOR (0 [ UPDOWN motor control
84 | DOWNMOTOR | _O | UP/DOWN motor control
35 TABLER =| Not used: (OPEN)
86 TABLEL, =| Notused. (OPEN)
7 LOAD OUT 0 _| Leading motor (M903) Load out output
8 LOAD IN © _| Loading motor (M903) Load in output
9 DF-LATCH, ‘© __| Latch output to digital fier. (PCMI7OIU)
—19—[Pin No| —-Pinname vo Description
90 XLT. (© _| Serial data latch output to DSP. (CDX2507AQ)
3 FOCUS SW, (© _| High-region gain down output to focus servo. (CXAI7828Q)
2 HIGH DUBB =| Net used. CH" LEVEL)
3 TESTI = [Not used. CH" LEVEL)
3 ‘OUT SW T_[ CD Tray output detection input
5 INSW T_[ 6D Tray input detection terminal
6 UPsw = [Ret used: (GND)
7 PANEL SW, 1_| SCD PANEL SW DET terminal
8 (CLOSE SW, | Close SW DET input terminal
3 OPEN SW =| Open SW DET input terminal
100 ‘Yoo = [Power supply. SV)
— 20 —1501 CXP82612-0060 (PANEL BOARD)
fin no] _Pinrane | v0 =
a a
3" ses 7 at
Spar 0
Se eee rense re] oF | ceopaca
apap oa mn oa
is} eer Roce se ne oe
os
is [aos [0 Pennie ace
a
is temo Mr
=e 5
anf eet
of eee
a ere)
a a
=| — 38
30 RST 1 _| Reset signal input terminal.
ST dnt
arFrm] Panam [0 =
ee
sao
a
Serpe
a
steep
a
| aa
ae ee
a ee
75 Voo_ =_| Not used. (+5V)
os eee
Lo fern ere
ae TT coer mi
een
aeHCD-H605
SECTION 7
DIAGRAMS
‘7-1, BLOCK DIAGRAM ~ CD SECTION ~
TI oece mie
OPTICAL PICK-UP BLOCK
co FOCUS/TRACKING SERVO,
EFW COMPARATOR
i cian a7)
c i
bIGITAL FILTER
‘A CONVERTER
e106
}—@k
DIGITAL SIONAL PROCESSOR
cy Sev0"
ic101
RASTER CONTROL
FOCUS TRACKING |
\a TRACED
t coi onive}
saa sz92
fears icvo2 aa Lokd ur “Loko wn
aanis | FOCUS TRACK ING
i Bettee | Coie ORIVE
L leat oa veh
ile
asain a
Sep paToR a, i:
SANE aoe
ioe
sues MTOR
SPINE HOTT
RIE
sfilbhe
rotoa ®
ie — umHCD-H605
7-2, BLOCK DIAGRAM ~ MAIN SECTION —
~ 25 — — 26 — a — 2HCD-H605,
© SEMICONDUCTOR LOCATION 7-4, PRINTED WIRING BOARDS ~ MAIN SECTION —
[No | tocaton [| Reto. | ocaton i 2 3 aici] aria) é aay, 8 a 0 ii CE 4 6 6 7 6 $9 [215120 2 22
31 vows | E-v2
7-3. CIRCUIT BOARD LOCATION bat team | bc13 s
or tems Jere | |, —_
Dive tome | 8-13 :
ores tooor | @-25
oioe [ex]
Dros a foes
Dios a | bce
Door Fn re) 9 a I es NIE) (Pe ee Re pment rr bo ee
Bane a |b B
a | bo
aoe
Dut aw | o-s
Dave ae | ec
bast as | cs
aoe ae | oe
ates | Boe
‘D803 c
Dave air | r-
aos aie | Foo
Dave ane | Fos
aor aim | e-7 ce
ain | Ge
ace | ote
gate | b-0 || awe | o-8 pp >
gee | o-2 || awe | Gor
fia || ane | 6-7
21 || awa | Hee oa (PowER 80880)
‘rowen]| Gear | Got
ett Onn aos o-u |
bz foc ff am | o-13
os | oo ff ows [ion | (E
pas fost ff awe | icin
os | ee |) Oreo | toe
uomoron tout cae | o-e |] oso | weve
bers | ont || ann | on
1c DETECTION bout essere Dee aii et
pet [cae fans fic | |p
COUNT SW board Deoz F-21 oats Het
fos
a owes | e-22 | ass | uu
eae Dest E-22 801 E-9
ae DI008 8-9 aso2 E-10
Grom | ee || nor | Ente
biscoerEcriow (@) vous ome ay 6
ray Moron ws teat en | es
test aero | 8-3
icro1 aon | oa s
eee Ietoz sie | Fie “aa @-—]
icr04 0813 E-10 sd
\erer ooo | u-e | ly
rere oes | Eze —
orewctose sibowd 2" @—
serenade ve ie Saurliecs re
te2ot Stooe | B-0
text
— ie ees
teres 1
‘cree
icnot
— [SENSOR BOARD)
Note:
o—:amecvadedtomtheconponan ste, | oe
{SEG} s Pato on thal wich sven
Astreiation
‘ND coadan
S08: avsasan mp
Seu anba “ere
1 Montan k
tr Ma |
5 Shure S
— 2 — 30 -* WAVEFORMS ~ MAIN SECTION —
Note :
+ Allcapactor rein F unless otherwise noted. pF: a uF
‘SOW erie are not indented excapt for electolcs and
tantalum.
= Ailresiors rein @ and Y4W orless unless other
“1 stent tr repsie
+ Vohage and wavelorms rede with respect to ground under
ro-signal (detuned J eonations.
no mask : FL
HCD-H605
+ Signa path
=D GPM > :PB(DECKA) a> =D
> EAM DS PB (ECKB) EH mc
(>: REC (DECK)
og
— 35
feb ny aM + Asean
+ T + ee to utnae eran
ae sand NW r : {nt exon ers
Pe ag fee ‘+ Vokages are taken with a VOM ( Input impedence 10M 2 ), eee
Tivsepnrape nt | teteonpeny eet par tx ours
4 M . td oprah orga. | aso mun fh wot igs Yetge vee may ented tee norma eon te tina
ome owe mae soe Tegktrccee [RSS ensue | “awl eave ecanpe Sher
Ropceecreae emncecuzrerwre | Yotage vero mayb ed ue toma reun
Io21® i101 @ 1c101 © 1c701@ Rela mt wit pain | pon or ts Yotace ve
Shea sombre wrens
+ (BE) : B+ Line
“IEE]:0- tne
7-5. SCHEMATIC DIAGRAM MAIN SECTION __# Refer to page 58 for Ic Block Diagram
asters eae|aee @eeanaeea 5s | 6 | 7] 8 ade |aaias eal 19 | 20 azii|e2e cae oes 27 | 28 | 29 Sis [iesozin(istas seijenisarsijesias ii siaaie|iiare:|ensai|et ss 40 | 41 | 42 | 43 | 44 | 45 | 46
A [MAIN BOARD] = a [Power BoaRD]Cw; Sse g egg eae rere ee ee ee EET |
az. 2 “sicge1
ao Pare he saa ES A |
e U
7 7 7
-—— toa 2 tat
>
— ay | [SENSOR BOARDT |
4 Le eos
yee]
4 Jeet eae
ce
F " lle
G Wit
ith
4
J = + |
i
i |
7 j | 248
4 | tars
‘i |
" ! |
l t [TRANSFORMER BOARD 1
' UB oy YF
: a a shundhoade
= : (iota e ieee Fe
steer 4 t
P L "a
4 [CHP BoaRD 1
e ' ers
R 1HCD-H605
Note :
+ Alcapastors ae in u Funes otherise noted. pF wy F ‘¢ WAVEFORMS ~ BD SECTION ~
ape ee a
eos ® ® ® @
‘¢ WAVEFORM — PANEL SECTION ~ pected. zomvee
®
To varie 7 | manent T “nan +
ee TD ZT ae
“Bal tim Va TR NADU {Lt t
@
+ Votage and waveorms ee de wit respect to ground under WD)
no-ignal conditions.
so mask : FM Icr01 ® Ic101 @ ic101
+ Votages are tahan wth @ VOM (Input impedance 10M 2),
‘dra evden © @ ®
+ Mavtoms are taken wth a oscllosope.
Vtg atone ay not ow ama proaicton T
Greens lr nt, T
7-6. SCHEMATIC DIAGRAM ~ PANEL SECTION ~ 4
ot 2 8 a BB ttt tt tt tt pt | Pt |e
Ic103@ Ic103. @
ee
Ic103 ® 1C103 ® 1103 @ Ic104@
A | [PANEL BOARD I ]
7-7. PRINTED WIRING BOARDS — PANEL SECTION —
1 2 3 Agia: [eateS 6 7 eee ane 10 1 ipa eis [ete Ag ee eg
(Panel _BoaRo (1/3))
© SEMICONDUCTOR
LOCATION
Reno. | toestion
zg
\
2
af
054-901) [1
[PANEL BOARD(3/3)] D519,
o
a Tie Sw BOARDY :
ThE eee ee
Ft | SHS 54 4 "ae
eletele
1
™
oo So Se
G20
[esrom)
' O a
askin Qatlre
| | aR
Ll.
(i
{Tc_sw_e0aRo)
2
a
2
{co_sw BoaRo})
Note:
+ O— : pats exacted tom the component sie.
+ ENG : Pater onthe side whic is seen.
— 38 — — 39 — —40— 41 = 42 —7-8. PRINTED WIRING BOARDS ~ BD SECTION ~
eee eee eee eee eee eee emcee
7-9. SCHEMATIC DIAGRAM - BD SECTION- _—@ Refer to page 41 for Waveforms. _¢ Refer to page 55 for IC Block Diagrams.
40 | 4
Ose om
{80 BoARD} (SIDE 8)
[TSC BOAROT ~ Tereoy
[0 soaRo}
OPTICAL PICK UP ALOK
KSS-2138 A
=
Ce
ag
{oe oeecon Boao}
fase)
ame
|
|
|
OPEN/CLOSE. ]
‘SW BOARD
BOARD
Ref. No, | Location
gg
e150: | 8-6
ie1soe | B-4
ar | e-13
iz | E-15
ais | G-i3
aisor | 8-6
aisoz | 6-5
ae
+ arts extracted from the components.
sh + Pater om the sie which enables seeing
(The eter ayers paters are not ncleatod)
[agagre®
[eouyt, ‘sw
BOARD.
‘caution
(Conductor Sie) the pater face are inca,
{Component side) parts face ae inciated.
Patten aco sa: Parts onthe pattem face ede coon trom
Pens face ide: Pars onthe parts face sie soon rom the
Le]
[2 MOTOR:
BOARD.
ip sw
BOARD
[P1SE, BRIEET!ON |
(BOARD
e IN SW
BOARD.
ag
+ Allcspactors ae ln F unos ctorwise noted. pF: uF
BOWY or loss are no ineted excepto electoyies and
alums
{110W ores unless otherwise
Les composantsiontiés par
poco porate numdte spec
fe
+): aston frre
+ Votage and waveforms are de with espoct to ground under
rno-ignal (CD) conditions.
re mark : STOP (C0)
+ Votages are taken with a VOM (Input impedance 108 2
\Votage variations may be noted due to normal production
tolerances
+ Wavetorms are taken wah a oscloscope.
\Votage vations may be noted ue 1 noma production
tolerances,
+ Cele number eler'o wavetorms,
* Signa! pat
=> :0D
eggHCD-H605 7-11, SCHEMATIC DIAGRAM ~ AUDIO SECTION ~
ssi Jee ce [sete cee | sees ce fea sence [ees esac Pieces | ese tens | ees gece [eee NO sees | see sees scene) eee [eee cece se @ seed | eee Oacen | esuer| Grades |saseed-raciai)
7-10. PRINTED WIRING BOARDS ~ AUDIO SECTION ~
7 2 3 4 5 6 Ta 8 9 70 - - - - - - - - - - - - - - - - - © WAVEFORM — AUDIO SECTION —
© SEMICONDUCTOR 2 : sl A [aupio BOARD] aus, on
LOCATION @ ®@
1
Fot.no. [ tocation | | g es] i oe a + t
ieee ene CLEAE_SWITCH BOARD) [LwOTOR BOARDI nae Pe ravpo| s2¥p2)
tcoo2 | @-4 B | '
wean | Hoe -——————— | n AL al
al corr = i 1 cae a
conte | B sn { eel Te2t Te2t
ase | H c oer | ve 8 ) mmeliane
ass: | F-9 ‘i ee, |
aroor | 5-2 % J | zl
s SS earone TwoToR BOARD]
arooz | B-6 1 sea i
c an > D 1
gu oe ’ # IC BLOCK DIAGRAMS ~ AUDIO SECTION ~
4 O1s e802 uPC1330HA
D eS en El nl SBP Lu
eon | [eo cave (a) ——
oe Oe - | i ean .
recon | 88S Pica: ! ran Er
8S, at +] an ae |
aie, | m @ 7 \ si, i ae =<
{aunio B04ROy ! oS { | #
E eo | aly ——— [a0] ate
i ‘af 1 1] ‘weet eaeaoeese =
i alike
5 6 4 -
=, D
i 4 | Te
F =n) t = | = = 2
ee Fs — -
: fe, H i | LEAF SWITCH BOARD J
| Note:
$ a :
ci a oP oy otf + Aeapastor ar uF anes ctor noted. FF
/ | sgrma mamma
6 H— | sofa ‘ i ' team
i + Avesta nad YW ors ules hese
2, Sal - ' | rey Sache
i as sy a t a ' se ure
Me : 1 | ws | adjustment for repair.
“ 4 ; | + Votage and waveforms ar do wih rapetie ground under
a i | re-signal onaions
z Ae fan Le casoan, Jf 1 neo mark = PLAY (70)
« —| (Ree
= Votages ae tatan wih a VOM (Iputinpedece 108 2
Note: Vonage vetlaone mayb noted dv te noma produon
° tien,
+ O— ! parts extracted from the component sie, K a0 ‘+ Waveforms are taken with a oscilloscope.
+ SES: Pat onthe ade wich seen, ‘Votage vartone maybe sted doe enamel potion
Fe Bs ‘tolerances.
eee + Chudoumbers foto wef
lis a + Signa path
‘i , 3 :PB(DECKA)
[ee e . a = . i‘ A eed 3B :pa(oecKe)
: a op: REC (Deck)
— 48 —449— — 50 — 51 — — 52 —7-12. IC BLOCK DIAGRAMS
MAIN SECTION ~
e102 Mc14052BcP
Ie109 Tes210P
SHIT sIsTOR
ic
1e701
PC1237HA
Iesoa Las617
[ao
i] fi}-eea— Ga
CL
(iB
— 53 —
— 54 —- BD SECTION —
le101 cxat7s2B0
Stee ete:
aaNOTE
©-XX, =X mean standardized parts, se
they may have some difference from the
original one.
‘© The construction parts of an assembled
ppart are indicated with a collation
rhumber in the remark column,
(Items marked “ » "are not stocked since
they are seldom required for rout
service. Some delay” should be anti
pated when ordering these items.
8-1, CHASSIS SECTION
consap-s8019
LleleUs
SECTION 8
EXPLODED VIEWS
(© The mechanical parts with no reference
number in the exploded views are not
supplied.
(© Hardware # mark) list and accessories
and packing materials are given in the
last ofthis pars list.
© Abbreviation
ND: Canadian AUS : Australian
EA: Saudi Arabia MX: Mexican
MY :Malaysia SP Singapore
A, MY, SP model
The components identified by
mark A\ or dotted line with mat
wat ie ety
lace only with part" nomber
specified
Lay compan Keil a
marque Ay sont fitiques pour la
ne
pice portant Ie numéro specific.Ref.No. Part No, _Deseription Remark | Ref.No. Part No, _Deseription Resark
1 4-970-846-21 case #10 A-4377-872-4 MAIN BOARD, CENPLETE (EA)
2 3-368-099-01 SCREW (CASE 3 TPZ) #10 A-4377-873-A MATN BOARD, COMPLETE. (83, mS)
3 4065-822-01 FOOT #10 AMMBTI-BTA-A MAIN BOARD, COMPLETE. (EZ, 9%)
#4 1-654-906-11 TRANSPORNER BOARD #10 A-4377-B75-A MAIN BOARD, COMPLETE. (US, CD)
#5 A-437T-S14-A POFER BOARD, COMPLETE (US, C10) All 1-558-948-41 CORD, POFER (EK)
5 AcA3TT-515-A POFER BOARD, OONPLETE All 1-575-651-21 CORD, POFER (EA, my, SP)
(EXCEPT US, CHD) All 1-500-896-11 CORD, PORER (US, c)
6 — 3-T03-244-00 BUSHING (2104), CORD (EXCEPT B, Hx) (lL 1-698-845-11 00RD, POWER (A)
#6 $-T03-571-11 BUSHING (S) (4516), CORD (mK) 412 _—1-569-007-11 ADAPTER, CONVERSION 2P (23)
87 4-949-235-01 100K 413 1-568-008-11 ADAPTER, CONVERSION 2 (EA, MY, SP)
#8 4-872-827-02 PANEL (UPPER), BACK (US)
1S 4-956-370-02 BAND, PLUG FIXED (AUS)
#8 4-972-827-12 Panel (UPPER), BACK (CAD) #16 $-101-946-28 LABEL, FUSE RATING (US, CRD)
8 4-970-827-22 PANEL (UPPER), BACK CBA SP) TT 1+$39-299-11 FUSE HOLDER
8 4-972-827-32 PANBL (UPPER), BACK GH?) #18 1-856-049-11 SENSOR BOARD.
8 4-972-977-42 PANEL (UPPER), BACK WX) ‘AFSOL —1-582-237-00 FUSE TIME LAG (8, 150A) (E, BA SP, KB)
#8 4-972-827-52 PANEL (UPPER), BACK (AUS)
AFSOL —1-532-748-11 FUSE, GLASS TUBE (6. 84/1281) (US, CRD)
+9 4-972-825-02 PANEL (LONER), BACK (US, ND, wx, MY) ‘AFS02 —1-582-259-00 FUSE (J. 600A) TIME LAG (EB, AUS, MY, SP)
+9 4-972-925-12 PANEL (LORBR), BACK (E BA, SP) WS 1-898-880-11 MOTOR, FAN (DC)
#9 ¢-972-925-22 PANEL (LOVER), BACK (AUS) ‘AT8OL 1-421-802-11 TRANSFORWER, POMER (US, CAD)
10 A-4377-971-A MAIN BOARD, COMPLETE (ALS) ‘ATSOL 1-427-886-11 TRANSPORMBR, PORER (EXCEPT US, CxO)
aeFRONT PANEL SECTION
(@A: PANEL BOARD (23)
PANEL BOARD (3)
RefNo, Part No,
5
5
53
54
55
56
sr
ar
Sr
58
59
Deseription Remark
X-4945-421-1 LID (A) ASSY, CASSETTE
X-4945-422-1 LID (B) ASSY, CASSETTE
4-070-844-01 KNOB (VoL)
4-810-848-01 KB (406)
4-970-847-01 BUTTON (EI-)
4-970-848-01 BUTTON (B5-8)
X-(945-163-1 PANEL ASSY, FRONT (US, CKD)
164-1 PANEL ASSY, FRONT (E21)
X-4945-165-1 PANEL ASSY, FRONT (E3, BA, AUS, MY SP)
4-810-902-01 SPRING (LID)
4-910-901-11 L1D (LOADING)
Ref.No, Part No.
60
81
+e
+8
+64
86
+88
+89
0
1
2
— 58 —
Description Renark
4-980-886-61 FOOT (FELT)
4-953-184-01 SCREN (6PTPRA We. 8x8)
A-ASTT-A96-A PANEL BOARD, OOMPLETE
1-854-908-11 CD $¥ BOARD
1-854-807-11 SUB PANEL BOARD
1-696-060-11 IRE, PARALLEL (FFC) (17 CORE)
5 ARAQKE S¥ BOARD
1-854-806-11 TC S¥ BOARD
11 WERE (FLAT TYPE) (21 cone)
11 WIRE (FLAT TYPE) (21 cone)
4-951-620-01 SCREW (2.68), «BVTP8-3, TC MECHANISM SECTION-1
(Tem-220wR2)
ot supplied
ef.No, Part No, Description Renark | Ref.No, Part No, Description Renark
|
101 X-4948-776-1 HOLDER (L) ASSY, CASSETTE WOT $-954-857-01 JOINT (LOCK LEVER)
102 X-4948-T75-1 HOLDER (R) ASSY, CASSETTE #108 §+387-709-01 LEVER (LOCK LEVER L)
103 4-858-231-01 SPRING (L), TORSION 109 4-965-877-01 LEVER (LOCK LEVER R)
104 4-958-232-01 SPRING (R), TORSION #110 1-854-803-11 HP BOARD (Us, cxD)
105 5-354-955-01 DANPER #110 $-4877-484-A HP BOARD, COMPLETE. (EXCEPT US, CHD)
106 3-908-611-01 FULCRUM, HOLDER 111 4-70-889-01 KNOB (NIC) (EXCEPT US, cx)
a pg8-4. TC MECHANISM SECTION-2
(Tem-220wR2)
Pogo?
oe
(retano@)—469
aot pod
15665
159.
155
r
14S
152 151
Fefato, Part No, Description fark | fete, PartNo, Deseription ferark
151 $-806-560-01 SPRING Azim aoJUSTENT 16 $-606-513-01 GEAR (), REEL
182 3-808-561-01 StREW (AAT ADJISTAEN) 165 3-917-14-01 SPRING, CouPRESSION
185 X-397-584-2 SLIDER (EID) ASSY 165 H-S867-504-1 REEL Ch) ASST
164 $-208-556-01 SPRING, HAD TOEGLE 1 465-01 TASKER (1.5), STOPPER
155 5-805-58-02 FITTING LOOK, HEAD 168 H-R960T5+1 TU ASSY
155 5-805-97-02 ROTARY BLOCK, HEAD 169 S-9ntn6-21 RIVET, PASH
+ 1st 5-808-59-01 stern azii Mo 9116-31 RIVET Pst
158 §-808-555-01 SLIDER (GEV SLIDER) #171 f-2607-31-4 AUDIO BOARD, conPLETE
153 5-S17-45-01 SPRING, TeNsiON 12 $-915-90-01 DET, WLP
160 5-348-845-01 ScReN (2x6) (8 TIGHT) | 17 Fe1ree-o1 seein coressiow
161 5-911-13-01 seni, TaxsioN WPLOL_1-$00-093-11 HeAD, mABETIC (PLAYBACK)
12 ¥-3970449-1 PINCH LEVER (REI ASS ARPELOL 1-S00-O94-11 HEAD, MAGIC REC/P/#RASe)
163 X-9967-588-1 PINGH LEVER (PRD) ASST
eens8.5, TC MECHANISM SECTION-3
(Tem-220wr2)
MF: MoTOR BOARD
Ref.No, Part No, Deseription Renark | Ref. Part No, _Daseription Remark
201 3-908-597-01 CAM (A) 215 3-908-00-01 LEVER (ReV-8)
202 3-008-608-01 SCRBY, STEP #216 1-650-659-11 LEAF SWITCH BOARD
203 X-S967-$80-2 ARH (A) ASSY, PR 217 3-908-595-01 Cat ()
204 X-8967-S86-1 FLYWNEEL (AR) ASSY 218 X-5967-581-2 ARH (B) ASSY, FR
205 — 3-808-610-01 PULLEY, TENSION 218 3-S11-114-01 SPRING (BR), ‘TORSION
206 3-908-598-01 LEVER (REV-A) 220 $-908-04-01 LEVER (TRIGGER 8)
207 3-808-801-01 SPRING (REY LEVER), TORSION 221 3-O11-115-01 WASHER, STOPPER
208 3-908-603-01 LEVER CTRIGGER 4) 222 X-8967-S87-1 CHASSIS ASSY, MECHANICAL,
208 X-8967-589-1 PLYWIEEL (BE) ASSY 4-223 3-381-716-01 HOLDER (LED)
210 3-908-605-01 SPRING (TRIGGER), TORSION 224 3-917-116-01 BELT (®)
211 $-805-609-01 GEAR, TRIGGER 225 X-8968-897-1 FLYTUEL (AP) ASSY
212 3-913-865-01 BELT (A) ML X-8969-110-1 MOTOR ASSY (CARSTAND
213 3-915-846-01 BELT (FR) We %-3369-111-1 NoTOR ASSY (TRIGGER)
214 X-8967-595-1 FLYTHEEL (BR) ASSY86. CD MECHANISM SECTION-1
(CDM33B-58D19)
fef.to, Fart No, Description Remark | Ref.te, Part Na, Desoriptfon ena
#251 K-496-115-1 CASSIS (6) ASX, SB | 23 1-6s-306-11 w/ woToR soko
252 5-3H3-600-01 CaN? Cee) | me -se2cs-01 cua
253 st2-019-02 GER (UD) 265 1-881-897-11 OINT SF BOARD
254 4-948-505-01 SERING (BUD, COMPRESSION #268 1-654-000-11 5 cb BOARD
255 (985-882-01 SPAGR 261 1-390-S76-11 WRG, FLAT T¥PS (19 co
256-967-1020 MASHER, STOPPR #268 Ko4845-718-2 LETER (® ASST
251 (351-196-01 SHER, STOPPRR 269 4-064-487-02 PILLEY (W/)
258 4-955-13601 SCRER (FTP He 6x8) Mo 364-477-01 BLT W/)
288 4-572-078-01 COW (1), GROOME M1 ES2017-01 Co @), aoowe
#260 T-49-T17-2 SLIDER ASST e212 Ho4045-716-2 SLIDER ASST
261 4-964-466-08 GEAR (JKT) #713 Ke49(5-719-2 LEVER () ASST
262 4-972-06-02 GEAR (CO 8) 1601 A-4650-502-4 HOTOR C0) ASST
par8-7. CD MECHANISM SECTION-2
(cbM33B-58019)
314 oe
312 i
intaven ~~]. Yaa SO
Za a =
338:
5
RefNo, Part No Description Remark | Ref.No, PartNo Description Renark
S01 4-972-860-02 LavER (SrorPEn) 322 4-064-463-02 GEAR (TRAY 8)
302 1-651-394-11 OPRN/CLOSE SV BOARD 323 4-957-798-01 WASHER, STOPPER
303 1-651-399-11 DI9C DET (8) BOARD 524 1-651-399-11 ID SENS BOARD
304 K-4845-114-1 BASE (TRAY B) ASSY, PITTING 325 4-967-198-01 SPRING (CLIGO, LEAF
305 1-651-391-11 TRAY MOTOR BOARD 328 1-651-395-11 IN SW BOARD
308 4-964-458-01 SLIDER (CLICK) 327 4-964-464-02 GEAR (DECELERATION)
507 4-966-481-01 SPRING (A), TENSION 528 4-964-465-02 PULLEY (TRAY)
308 4-964-459-01 LEVER (STOPPER) 529 4-964-476-01 BELT (®)
509 4-964-482-01 SPRING (B), TENSION 330 3-319-030-01 BELT (MIDRAY)
B10 4-964-453-01 TRAY (WAIN) 331 4-964-462-02 GHAR (TRAY F)
311 1-851-398-11 DISC DET (A) BOARD 382 4-964-199-01 stocteR
312 1-452-T19-11 HAGRET ASF 4383 -K-4944-827-1 TRAY (SUB W0,5) ASSY
313 4-964-492-01 BASE QUGNET), FITTING 334 K-4944-826-1 TRAY (SUB NO. 4) ASSE
31 3-831-S76-11 RIVET 885 K-4944-825-1 TRAY (SUB NO.3) ASST
315 (-972-861-01 ROPE 386 K-4944-824-1 TRAY (SUB NO.2) ASSY
316 4-872-862-02 GuIDE (ROPE) 387 K-4944-823-1 TRAY (SUB NO.1) ASSY
S17 4-872-863-01 SPRING (ROPE), TENSION 338 4-993-134-01 SOREY (+PTPHL MZ. 5X6)
9-318 4-964-460-03 LEVER (STOC®) 9-339 4-967-859-01 CUSHION
519° 1-851-382-11 MID S¥ BOARD 340 3-701-439-21 WASHER
20 4-964-455-01 SLIDER (SELACTION) S41 £-951-620-01 SOREF (@.6%8), +BVTP
321 X-4944-650-1 LEVER (GOOSENECK) ASSY S02 X-4944-463-1 MOTOR (TRAY) ASSY
— 63 —8-8. CD MECHANISM SECTION-3
(BU-SBD19)
355
356
‘The, components identified by ] Les composants identifiés par une
-mgck f\ of dotted line with mark | marque es pour Ia
& af ciel or sete naw 4
{place only with par number |Ne les remplacer_que par_une
specified. | pitce portant le numéro spécifié.
Ref.No, Part No, Description Remark | Ref.lo, Part No, _Daseription Renark
351 4-851-620-01 SOREV (2.68), <2VTP 358 1-169-68-11 WIRE (PLAT TYPE) (16 CORE)
352 A-4673-402-A BD BOARD, COMPLETE. 357 4-817-567-01 Gear GD
353 4-017-565-01 SHAFT, SLED 358 4-917-564-01 GeaR (P), FLATNESS
354 4-961-940-01 INSULATOR (BU) LO) 4-4604-863-4 HOTOR (SPINDLE) ASSY
(A855 6-B48-367-11 DEVICE, OPTICAL KSS-2138/K-N Wi02 —X-4917-504-1 MOTOR (SLED) ASSY
— 64 —NOTE
‘© Due to standardization, replacements in
the parts list may be different from the
pants specified in the diagrams or the
Components used on the set.
© 30K) -X' mean standardized pars, so
they’ may have some difference from
the original one
© RESISTORS
All resistors are in ohms
METAL : Metal-film resistor
METAL OXIDE : Metal oxige-fm ress
F:nonflammable
SECTION 9
ELECTRICAL PARTS LIST
1 Items marked * # "ate not stocked since
they are seldom required for routine
service, Some delay should bé antici-
pated when ordering these items
‘@ SEMICONDUCTORS
In each case u 4 for example
Ut fk Are UPA BPA,
UPB ff Bone UPC on fF
uPD._.: PD.
© CAPACITORS
wea
coils
oH: aH
(¢ Abbreviation
ND : Canadian
AUS : Australian
BD
ae
mig fo cae ne wh mek
op Acetate
spectied”
a
Srey eer ean
sécurité. 4
NEMS remplaer que par_une
Dice poate mundi pete
‘When indicating parts by refer
fence number, please include the
board
EA: Saudi Arabia MX: Mexican
MY :Malaysia SP: Singapore
fef.No, Part No. Description Remark | Ref.No, Part No. Description Renark
$-4873-402-8 BD BOARD, COMPLETE cast 1-164-250-11 cenmite GHP 0, 01uF sor
sevvrvesnassasents C139 1-163-255-11 GERMIC CHIP ZPF Sk
C10 1-163-285-11 CERAMIC CHIP ZF BSS
< CAPACITOR > C11 1-165-056-81 CERMIC CHIP 0. uF a5
2 1-168-098-91 CERMMIC CHIP 0. 10F 25
clo. 1-126-Gov-11 eter GHP TF toe
ioe 1-188-215-11 cemiutc CHIP O.001uF «5X SOY | CLAS 1-185-201-11 TANTALIN CHIP OPK a
C103 1-161-346-11 CRAMIC CHIP uP tov | C146 1-195-201-11 TAMTALIN CHIP LOU ORY
C105 1-163-058-81 CoRMIC CHIP 0. oF a | CaT 1-16s-275-11 cRRMIC GHP OOOO
ing 1-164-605-11 CERMIC CHIP 0. 00zaur sx OV | Clas 1-163-275-11 CERMNIC CHIP 0.001 SK 50
CUS 1-166-346-11 CERAMIC CHIP TP 1
ClOT 1-164-685-11 CRMC CHIP G.00zzuF 58 SOY
008 1-164-282-11 CERAMIC CHIP 0. OUP Sov | CSS 1-186-259-11 TAMTAL, GHP IOP 20K BF
108 1-164-250-11 CERMNIC GHIP 0. o1uF sor | Cusd 1-160-235-11 ceRMC GMP 2PF BS SOY
C110 1-165-988-11 CHRMIC CHIP 0.0380 108237
CN 1-168-038-91 CERAKIC CHIP 0. 1F 239
301 1-162-289-31 CERAMIC sore tok soy | 88) I-a10-780-11 wouCTOR Tat
302 1-124-445-00 ELACT loout = 20 tov | LAS 1-410-780-11 INDUCTOR a
C303 1-162-282-81 CERANIC 100P 10K 50
(304 1-130-483-00 MILAR oor 5K SOF << TRANSISTOR >
C305 1-107-715-11 ELECT mE 2016
62k §-729-142-46 TRANSISTOR 25C2001-LK
Cait 1-162-260-81 CeRAMIC soups oy sov | QSa2_8-729-142-48 TRANSISTOR Z5CZ00I-LK
C313 1-162-282-31 CERANIC oor 108 Sov | Q23_8-729-801-93 TRANSISTOR 2501387
Coie 1-130-487-00 WHLAR Goze 5x 50V | QB51_8-729-800-65 TRANSISTOR DTALAAES
C315 1-124-254-00 LACT TF 20816
C3al1-186-434-11 FLL 2p 630 « RESISTOR >
case 1-162-288-31 cenaute ssorr 108 soy | R301 1-247-881-00 CARBON 20k saan
333 1-162-208-31 CeRAMIC ame 3% Sov | R302 1-249-408-11 CARBON mo s/n
AOL 1-162-268-31 CERAMIC sop 10k S07 | R303. 1-249-438-11 CARBON mK S/n
coe I-ted-448-00 ELECT oour = 20k tov | RaDd1-247-889-00 CARBON Tok 551/48
403 1-162-282-31 CERMIIC oop? 10k Sov | R305 1-247-858-11 CARBON 1k 581
(l04 1-190-489-00 WMLAR cow 5 sov | SIL 1-247-881-00 CARBON ok sk 1A
40s I-t0r-T15-11 LECT tau 208 «6 | RBZ 1-247-807-31 CARBON loo Lat
CAN 1-162-289-31 CERBIIC a90PP 10k Ov | RSL 1-247-882-11 CARBON oe 1A
13 1-162-282-31 CERBIIC woop? 10K Sov | RBIS 1-247-850-11 CARBON ems 1A
cad 1-130-487-00 MMLAR oeaue © 5 Sov | REST 1-249-430-11 CARBON eA
cas 1124-234-00 Bact ze 208 ev | 4OL—1-247-881-00 CARBON woe xa
31 1-136-484-11 FIL wore Sx gay | Rb2 1-249-408-11 CARBON a eG
(432 1-162-288-31 CERNMIC 330PP 10 SOV | RAGS 1-249-438-11 CARBON mK 5% AN
433. 1-162-208-31 CERAMIC ape Be Sov | dod 1-247-889-00 CARBON 7K 1
0601 1-126-187-11 ELECT Wu = 20% tev | RAS 1-247-858-11 CARBON ROX LA
0602 1-126-187-11 ELECT tout 20 tev | RAIL 1-247-881-00 CARBON 20K sx 1/4
11 1-126-187-11 ELECT rout 20 ey | Rae 1-247-807-31 CARBON er
512 1-126-157-11 ELECT uF 208 ty | RAMA 1-24-882-11 CARBON 130k 5x 1/4
coal 1-136-601-11 FILM O.olur 5X G30 | RAIS 1-247-850-11 CARBON aa KT
cee 1-124-925-11 ELECT 2.2uP 208007 | RAST 1-249-430-11 CARBON eA
323 1-136-155-00 FILM osu sx sv | ROL 1-249-409-11 CARBON 0 Ko
C524 1-180-481-00 WHLAR Looseur sx SOV | R602 1-249-409-11 CARBON mo ue
525 1-130-481-00 MYLAR O.0o6suF 5x SOV | R608 1-249-409-11 CARBON m0 58 1/8
ey T-ted-90g-11 eLacT 10 20% SOV | R808 1-248-433-11 CAREON 2K SAN
528 1-136-153-00 FILA owe = 5% SOF | ROLL 1-249-409-11 CARBON m0 581A
egAUDIO | |MOTOR| |CD SW | |COUNT SW |DISC DETECTION (A) | |DISC DETECTION (B)
Ref.No, Part No. Remark | Ref.No. Part No, Description Remark
R612 1-249-409-11 CARBON zo ska R523 1-249-427H11 CARBON 6.8 58
Af62)1-212-851-00 FUSTBLE 56 ok NF R594 1-247-807-31 CARBON 100 §%1aN
‘R622 1-212-851-00 FUSIBLE 56 Sk NF R595 1-249-401-11 CARBOR 7% Aan
623 1-249-432-11 CARBOR 1k 58 1/H 691-894
R624 1-249-430-11 CARBON 1k S&H 1-247-807-31 CARBON loo 3% AR
695-898
R625 1-249-420-11 CARBON 10k ska 1-249-401-11 CARBON 7% An
O51 1-247-856-0 CARBON nk 1AW
652 1-247-856-00 CARB aK OK IAW «< svrTOH >
RSS 1-249-440-11 CARBON roo XW |
| SSI 1-854-303-21 SWITCH, TACTILE (DISC 5)
‘VARIABLE RESISTOR > S512 1-$54-305-21 SUITCH, TACTILE (DISC 4)
S513 1-$64-308-21 SVITCH, TACTILE (DISC 3)
VOL 1-241-762-11 RES, ADJ, CARBON 2.2K (PB LEVEL L) S8M 1-$54-305-21 SWITCH TACTILE (DISC 2)
RSL] 1-241-162-11 RES, ADJ, CARBON 2.2 (PB LEVEL L) SSIS 1-$64-303-21 SWITCH, TACTILE (DISC 1)
VSL 1-280-725-11 RES, ADJ, CARBON 220K (REC BIAS L)
VOL 1-241-762-11 RES, ADJ, CAREON 2.2 (PB LEVEL) ‘eeeseeetseeeensnscessenenneennnaenvoneennennesnnneeannns
VAIL 1-241-762-11 RES, ADJ, CARBON 2.2K (PB LEVEL)
+ 1-851-897-11 COUNT SP BOARD
VGA] 1-230-725-11 RES, ADJ, CARBON 200K (REC BIAS R) sossnennssestt
VSI. 1-241-763-11 RES, ADJ, CARBON 4.7K
(TAPE. SPEED NORMAL) «< Sermo >
GSE 1-241-163-11 RES, ADJ, CARBON 4.7K (TAPS SPEED HIGH)
S502 1-892-193-11 SWITCH, PUSH (1 KEY) (TRAY DORN)
(TRANSFORMER > | $¥503. 1-572-126-11 SPITCH, PUSH CL KEY) (COUNT)
seastsseceatessnssestoeneunnesesaseesseseneteatsneeteeaaaty
621 _1-423-980-11 TRANSFORVER, BIAS OSCILLATION
senevivecesntntesasstaseesnsstesstttiteestiteerssttieseint | 1-851-$98-11 DISC DETECTION (A) BOARD
‘eeeeeeereneneeetteste4e
908-11 CD $# BOARD
sersevvesee «< pone >
«< Doge > sO 8-719-028-95 LED___TLNIIT (DISC DET)
sasssenevnseennannvsseneeseeenseetetesenseatesestessesnntt
502 8-719-082-98 LED SeLs8z0A (DISC 2)
D503 8-719-032-98 LED SELSBZOA (DISC 4) . 1-851-$99-11 DISC DETECTION (8) BOARD
D515 §-719-032-98 LED SELSBZ0A (DISC 1) eseeeveseesneennennnne
S16 8-719-032-98 LED SELSBZOA (DISC 3)
DSIT 8-719-082-98 LED SELS8204 (DISC 5) 4-964-461-02 HOLDER (SENSOR)
|
D550 8-719-082-98 LED SELS8204 (DISC 1) «< cowwector >
DS§1_8-719-032-88 LED SELSBZOA (DISC 2)
D552 §-719-32-8 LED SELS8Z0K (DISC 3) #8610 1-S68-941-11 PIN, CONNECTOR 3P
D553 §-719-032-98 LED SELSBZ0A (DISC 4)
DSS4 8-719-092-98 LED SELE8Z0A (DISC 5) < TRANSISTOR >
0555 -719-082-98 LED SELSB204 (DISC 1) 0501 8-729-018-23 TRANSISTOR TPS826
SSG 8-718-082-38 LED SELS8Z04 (DISC 2)
Sst 8-719-032-98 LED SBLE8Z04 (DISC 3) « RESISTOR >
D558 §-719-82-98 LED SELS820A (DISC 4)
D559 8-719-032-98 LED SELEBZ0A (DISC 5) R502 1-249-425-11 CARBON ATK 58 aH
eovseaveveeneneeeecenneenenatatoesesneeeeesenneteenneentese
«< nesistor >
R519 1-249-416-11 CARBON sea ska
520 1-249-418-11 CARBOR Lak S/H
R521 1-249-420-11 CARBON ak 5K 1/4"
522 1-248-423-11 CARBON SM SS LAN
‘The, components identified by | Les composants identifiés par une
mark (A\ or dotted line with mark | marque A sont critiques pour la
‘afe eritical for safety secure
feplace only with par number | Ne les remplacer que par une
| specified pitce portant le numéro spécitié.
68 —HP}
Ref.No, Part No. Description Remark | Ref.No, Part No Description Renark
ND BOARD, COMPLETE (B.A, AUS, WK MY, SP) | CTA I-124-477-11 ELECT ane 208 SN
1 HP BOKD (S00) ce icieeaiseal carne Ear
atseeeesenene (exert us, 00)
| cast -162-204-21 cermnic 0.00F 108 SO
4-942-204-01 PLATE, GROUND | (EXCEPT US, CXD)
| crs ase-ais-n comme are ag SOY
‘< CAPACITOR > (EXCEPT US, CXD)
| 753 1-162-200-31 CERAMIC SOF 0K S08
cr iee-ses-n1 ECT 2. 20k oy (exerts, 00)
(eiert 1s, |
C702 © 1-126-933-11 ELECT 100uF_ «20810 | C158 1-162-290-31 CERAMIC ATOPE 10% SOV
(Eke 15,00) | (EXCrT 8,00)
70a 1-162-06-11 Comte O.01uF —s0K 16t cass v-igo-aer-s1 commie amore tok SOY
(eiert 15,00) 5,0)
104 1-161-494-00 cote. 0, 020uF 250 case 112t-00-00 user ame om oH
(excer 15,00) | cence us, 0)
C105 1-124~903-11 ELECT uF 20% SOV | C1S9 1-162-215-31 CERAMIC ATP sk SOV
cexceer ws,cw) | rat I-ieoaee-al comic = Sr Lox SY
| exc us, 8)
10s 1-130-78-00 WAR o.o0KTuP SX SOF
ceicert ws,a0) | cree rse-2-s1 mmc OFF tos sor
ror aso-ea-00 nan o.coisae sk “aot exter us, 00)
cater ws | cio iste omc sor
ros 1-186495-11 FILM o.ossur sk |
(exert 5,00) « camecroe >
709 1-126-165-00 FIN ota sk
cexcerrws,cm) | mor a-se4-70r-11 Pm, comectoR (SILL 11°) SP
cro 1-1%6-165-00 FILIP 90s 1881-Ter-LL Pu (aeRO COWECTON SP
(ERErT US.)