MSP 400 Series Transducer Instruction Sheet
pss
Model Description Code
Eee
907 = bat
{oe = Toast pea
a. Output
a > bo Type- 3
‘torn Output
Type - 4
1 = 28.coble
2 > En esele
3 2 loicone
2 paclaxd Connector
EXAMPLE: MSP-400-500- ‘N-1
Output
Type -5
cid Connects Type -3 4
Pn A= + Supply
Bn = GND
Pac = Ouiput * Packard Mating Connector
| ea, - Housing pin: 12078090
Packard Comecto: Type § 3.60, - Pins pin: 12103887.
ena
eng
WARNING: READ BEFORE INSTALLATION
in ig ts orcas cre snout akn when
Voltage Output Sensor Wiing Configuration
inglerEndedlAmpltiod Outpul
Vorage Output Sensor Witng Configuration
{Sngle-tndediampitied Output
aa
ECT
‘Curent Output
Sonsor Wring Configuration
Coble Output Type -3 &-4
lle. | Res supev"
Black = GND
While = Outout
teen = Not used
Bare ~ Dra [connected to housing)
~_ | Cable Outout me 5
>> | Red
ai
wie
Ce | sicen
Bore ~ Drain (comected to housing)re ine MSP 400 Series Transducer Instruction Sheet
Performance Specifications
Accuracy (combined linearity, +0,5% of FS Span
hysteresis and repeatability)
Media compatibility 17-4 PH stainless steel, (316 stainles steel available upon request)
Pressure overload 2x rated pressure
Burst pressure 5x oF 20,000 psi, whichever is less
Long term stability (1 year) 0.25% of FS Span (Typical)
Zero Offset (+2% of FS Span
Span tolerance +2% of FS Span
Load Impedance For voltage output configurations use > 100K Ohms for quoted performance:
For 4-20 mA output configuration use 0.05*{Vsupply-10) K Ohms for max.
loop resistance,
Bandwidth (-308) DE to | Khz (Iypical)
Operating temp range -40? to 185°F (-40" to 85°C)
Compensated temp range 32° to 158°F (0° to 70°C)
Zero thermal error <+1.5% of FS Span
Span thermal ertor <+1,5% of FS Span
Storage temperature range -40" to 212 (-40° to 100°C)
Shock 50g, 11 msec half sine shock per MIL-STD- 202F, method 2138, conalion A
Vibration +209 MILSTD-810C, Procedure 514,2, Figure 514.2-2, curve L
EMUREI EN 60081-2
EN 50082-2 (10 V/M, 26-1000 Mhz)
Note: All performance and electrical specifications are referenced to 25°C, unless otherwise indicated
Ce !
Dear Valued Customer:
The enclosed pressure transducer has been manufactured, tested and inspected in accordance with all applicable
procedures and practices as established in our registered ISO 9000 quality system. We cerity that this sensor is in
full conformance wih all written specifications as Contained in this instruction sheet.
Signature: Charlie Chen
Tile: Quality Manager, MSIJL
Neasuremen Specialise. Sensors Group, Mictotusea Sensor DWsion 1000 Lucas Way Hompton, VA 28666, Questions Gallou' help ine @ 1-600-745-6008,
Fax (610) 650-1509. For more information visit our website at WWW MSIUSA.COM, E-mal address. SENSORS@OMSIUSA. COM.