(ex
3.3. Setting Procedure (Addresses 110 to 115 in C1 Menu)
Before setting data, ensure thatthe voltage is within the rated voltage, and insert
the power plug ofthe scale to the power supply outlet
ZX _| The indicator may be damages ifthe applied power votago is
conrTian | tse the rated range
Operation Display
1. Ctmenuentry
+ Press the ON/OFF key[ totum on the
power.
+ Keep pressing the fi] orl‘) key white
tho all segmonts are ft up.
+ Press the| 1) or] key.
‘Country no. setup
+ To select he grace use
the FE9) or 2] and [EF] or 'F"] keys to
ero tumbatsup and foun
[Example] “3° for ASIA
+ Prose the] (5) kay
3 Scala no. setup
+ To select the required scale no.. use the
‘or [2] anc or
Elon [Jonah Hoc kesto sat a E Al- oe
[Example] "2" for 30kg specification
+ Prove tho] o hy.
16 W/ Weigh indicator (WED) Setup Manual‘4, Weight selection for span.
adjustment
Vig selections promod in the
Ietening manner
MOsO-r 725-9115. Ink unto
wiging capacty,
TODO 3185-185 0in nto
wadigeoeay
1 Ose the or (Pon 0 Feye
tesco aber up and down
{Example} Withhe 1 80h9 scale capacty,
sole 101mg Touse 7565
wet into
« Press tne] orf} ke
Ab - 0)
Using weight as heavy as the
weighing capacity In “kg” unt.
LAG-20
Using 1/2 weight of the
‘weighing capacity in *kg" unit
5. “Ib” / “kg” select
+ In order to switch between “Ib* and “kg
pros the key an the key
a
«Press tha ho.
foro aucinat
+ Aor sting he weight ens hat
noting ead ong or ltr.
Bre pes the [ao FO Ke.
The prov et Zoro Poin ND dla
aloed
‘The Zero Point mark «@ lights up.
+ Press the Fi] key.
The dps rod tuto 2000
counts
‘The Zero Point mark turns off.
‘weighing capacity in “Ib
(Pound) unit
‘The Zero Point indicator
lights up,
cauee
7
|W Weigh tdicatr (NVE-D) Setup Marl
a7, Span adjustment
+ Place the selected weight on he weigh
Blator and ross the| Hr [] ky.
{Example}
Wight selection nas been set as 11.0 in
stop 4, 60000 counts when resolution i
116000
60000 + Zero Point 20000 makes 80000
+ {Cali (Calibration) Calculation process,
is executed.
+ [C- OK] (Calibration OK) Calculation
results is alr
+ Adjusted count calculation result is
displayed,
[C-Err] is displayed in the case that the
span adjustment is performed without
weight loaded. Place weight and press the
PAF |or [7] key again.
aoooo
bis
Calibration error
8. Fine span adjustment (Normally not
required)
“This step is carried out only when fine span
adjustment is required.
Refer to the following page regarding fine
span adjustment procedure.
8
|W Weigh ndiatr(WWB-D) Setup Manust
39. Data memory
Country No,, Scale No., Zero point and the
Span data must be memorized in the
E2ROM.
+ Remove the weight from the weigh
platter.
+ Afr all settings are made, push the
Memory Switch on the main board using
‘an object with a thin, slender tip to store
the set data into EEPROM,
Note: The memory switch is located on
the main board as ilustraled
below. It is used for data rewriting
at Test mode initialization, and for
data rewriting at country/span
adjustment in Test mode.
+ [S~ OKs displayed whon memory
writing has been properly performed.
G- of
10. Prose ho [a] or[ >] poy to vlase
The depiay hums Al data
71, Pres te ONOEP key [] w nd
ebuad
OFF status,
19
|W Weigh indicator (18-0) Soup Manual