Professional Documents
Culture Documents
Yageo 1206
Yageo 1206
5%, 1%
GENERAL PURPOSE CHIP RESISTORS
DATA SHEET
Product specification – Sep 03, 2004 V.2 Supersedes Date of Mar. 06, 2003
Product specification 2
10
Chip Resistor Surface Mount RC SERIES 1206 (Pb Free)
SCOPE
This specification describes RC1206 series chip resistors with lead-free terminations made by thick film process.
ORDERING INFORMATION
Part number is identified by the series, size, tolerance, packing type, temperature coefficient, taping reel and
resistance value.
TYPE/ START TOL. RESISTANCE PAPER / PE TAPE ON REEL (units) (2) (1) TOLERANCE
1206 IN (1) (%) RANGE 5,000 10,000/not preferred 20,000 F = ±1%
RC01 2322 ±5% 1 to 10 MΩ 711 61xxx 711 51xxx 711 81xxx J = ±5%
RC02 2322 ±1% 1 to 10 MΩ 724 6xxxx 724 7xxxx 724 8xxxx (2) PACKAGING TYPE
HRC01 2350 ±5% 11 to 22 MΩ 520 10xxx - - R = Paper/PE taping reel
Jumper 2322 - 0Ω 711 91032 711 91005 711 92004 (3) TEMPERATURE COEFFICIENT
OF RESISTANCE
(1) The resistors have a 12-digit Last digit of 12NC
– = Base on spec
ordering code starting with Resistance decade (3) Last digit
2322/2350. (4) TAPING REEL
0.01 to 0.0976 X 0
(2) The subsequent 4 or 5 digits 0.1 to 0.976 X 07 = 7 inch dia. Reel
7
indicate the resistor 10 = 10 inch dia. Reel (not preferred)
tolerance and packaging. 1 to 9.76 X 8
13 = 13 inch dia. Reel
10 to 97.6 X 9
(3) The remaining 4 or 3 digits (5) RESISTANCE VALUE
represent the resistance value 100 to 976 X 1
with the last digit indicating 1 to 9.76 kX 2 5R6, 56R, 560R, 5K6, 56K, 22M
the multiplier as shown in the 10 to 97.6 kX 3 (6) RESISTOR TERMINATIONS
table of “Last digit of 12NC”.
100 to 976 kX 4
(4) “L” means lead-free L = Lead free terminations (pure Tin)
1 to 9.76 MX 5
terminations.
10 to 97.6 MX 6
ORDERING EXAMPLE ORDERING EXAMPLE
Example: 0.02 X = 0200 or 200
The ordering code of a RC02 The ordering code of a RC1206
0.3 X = 3007 or 307 chip resistor, value 56 X with
resistor, value 56 X with ±1%
tolerance, supplied in tape of 1X = 1008 or 108 ±1% tolerance, supplied in 7-inch
5,000 units per reel is: 33 kX = 3303 or 333 tape reel is: RC1206FR-0756RL.
232272465609L. 10 MX = 1006 or 106
NOTE
1. The “L” at the end of the code is only for ordering. On the reel label, the standard CTC or 12NC will be mentioned an additional stamp
“LFP”= lead free production.
2. Products with lead in terminations fulfil the same requirements as mentioned in this datasheet.
3. Products with lead in terminations will be phased out in the coming months (before July 1st, 2006)
www.yageo.com
Sep 03, 2004 V.2
Product specification 3
10
Chip Resistor Surface Mount RC SERIES 1206 (Pb Free)
MARKING
RC1206
First two digits for significant figure and 3rd digit for number of zeros
Fig. 1 Value=10 KΩ
Fig. 2 Value=10 KΩ
For marking codes, please see EIA-marking code rules in data sheet “Chip resistors instruction”.
CONSTRUCTION
The resistors are constructed out of
a high-grade ceramic body. Internal handbook, 4 columns
protective coat
DIMENSIONS
Table 1
protective coat
TYPE RC1206 I1
www.yageo.com
Sep 03, 2004 V.2
Product specification 4
10
Chip Resistor Surface Mount RC SERIES 1206 (Pb Free)
NOTE
1. For Paper/PE tape and reel specification/dimensions, please see the special data sheet “Packing” document.
www.yageo.com
Sep 03, 2004 V.2
Product specification 5
10
Chip Resistor Surface Mount RC SERIES 1206 (Pb Free)
FUNCTIONAL DESCRIPTION
POWER RATING
Pmax MRA632
RC1206 rated power at 70°C is 1/4 W (%Prated)
V=Continuous rated DC or
AC (rms) working voltage (V) Fig. 5 Maximum dissipation (Pmax) in percentage of rated power
as a function of the operating ambient temperature (Tamb )
P=Rated power (W)
R=Resistance value (X)
PULSE LOADING CAPABILITIES
MBD641
10 4
Vmax
(V)
1.2/50 µs
3
10
10/700 µs
10 2
10
10 10 2 10 3 10 4 10 5 10 6 R n (Ω) 10 7
Fig. 6 Maximum permissible peak pulse voltage without failing to open circuit’ in accordance with DIN IEC 60040 (CO) 533 for type:
RC1206
www.yageo.com
Sep 03, 2004 V.2
Product specification 6
10
Chip Resistor Surface Mount RC SERIES 1206 (Pb Free)
3 MBD585
10
P max
(W)
10 2
single pulse
10
t p /t i =1000
10 1
10 6 10 5 10 4 10 3 10 2 10 1 1
t i (s)
Fig. 7 Pulse on a regular basis for type: RC1206; maximum permissible peak pulse power as a function of pulse duration for single
pulse and repetitive pulse tp/ti = 1000
MBD586
600
Vmax
(V)
400
200
0
10 6 10 5 10 4 10 3 10 2 10 1 1
t i (s)
Fig. 8 Pulse on a regular basis for type: RC1206; maximum permissible peak pulse voltage as a function of pulse duration
www.yageo.com
Sep 03, 2004 V.2
Product specification 7
10
Chip Resistor Surface Mount RC SERIES 1206 (Pb Free)
Thermal Shock MIL-STD-202F-method 107G; At –65 (+0/–10) °C for 2 minutes and at +155 ±(0.5%+0.05 Ω) for 1% tol.
IEC 60115-1 4.19 (+10/–0) °C for 2 minutes; 25 cycles ±(1.0%+0.05 Ω) for 5% tol.
Low MIL-R-55342D-Para 4.7.4 At –65 (+0/–5) °C for 1 hour; RCWV applied ±(0.5%+0.05 Ω) for 1% tol .
Temperature for 45 (+5/–0) minutes ±(1.0%+0.05 Ω) for 5% tol.
Operation
No visible damage
Short Time MIL-R-55342D-Para 4.7.5; 2.5 × RCWV applied for 5 seconds at room ±(1.0%+0.05 Ω) for 1% tol.
Overload IEC 60115-1 4.13 temperature ±(2.0%+0.05 Ω) for 5% tol.
No visible damage
Dielectric MIL-STD-202F-method 301; Maximun voltage (Vrms) applied for 1 minute No breakdown or flashover
Withstand IEC 60115-1 4.6.1.1 Type RC1206
Voltage
Voltage (AC) 500 Vrms
Resistance to MIL-STD-202F-method 210C; Unmounted chips; 260 ±5 °C for 10 ±1 ±(0.5%+0.05 Ω) for 1% tol.
Soldering IEC 60115-1 4.18 seconds ±(1.0%+0.05 Ω) for 5% tol.
Heat
No visible damage
Life MIL-STD-202F-method 108A; At 70±2 °C for 1,000 hours; RCWV applied for ±(1%+0.05 Ω) for 1% tol.
IEC 60115-1 4.25.1 1.5 hours on and 0.5 hour off ±(3%+0.05 Ω) for 5% tol.
www.yageo.com
Sep 03, 2004 V.2
Product specification 8
10
Chip Resistor Surface Mount RC SERIES 1206 (Pb Free)
Bending JIS C 5202.6.14; Resistors mounted on a 90 mm glass epoxy ±(1.0%+0.05 Ω) for 1% tol.
Strength IEC 60115-1 4.15 resin PCB (FR4) ±(1.0%+0.05 Ω) for 5% tol.
Bending: 5 mm No visible damage
Noise JIS C 5202 5.9; Maximum voltage (Vrms) applied. Resistors range Value
IEC 60115-1 4.12 R < 100 Ω 10 dB
100 Ω ≤ R < 1 KΩ 20 dB
1 KΩ ≤ R < 10 KΩ 30 dB
10 KΩ ≤ R < 100 KΩ 40 dB
100 KΩ ≤ R < 1 MΩ 46 dB
1 MΩ ≤ R ≤ 22 MΩ 48 dB
Intermittent JIS C 5202 5.8 At room temperature; 2.5 × RCWV applied for ±(1.0%+0.05 Ω) for 1% tol.
Overload 1 second on and 25 seconds off; total 10,000 ±(2.0%+0.05 Ω) for 5% tol.
cycles
Moisture MIL-STD-202F-method 106F; 42 cycles; total 1,000 hours ±(0.5%+0.05Ω) for 1% tol.
Resistance IEC 60115-1 4.24.2 Shown as figure 9 ±(2.0%+0.05Ω) for 5% tol.
Heat
No visible damage
www.yageo.com
Sep 03, 2004 V.2
Product specification 9
10
Chip Resistor Surface Mount RC SERIES 1206 (Pb Free)
80 − 98% 80 − 98%
75 90 − 98% RH RH 90 − 98% RH RH 90 − 98% RH
temperature
[°C] initial drying
24 hours
rate of change of temperature is unspecified,
50
however, specimens shall not be subjected to
radiant heating from chamber conditioning processes
end of final cycle;
measurements
+10 °C (+18 °F) as specified in 2.7
25 −2 °C (−3.6 °F)
initial measurements
as specified in 2.2 circulation of conditioning air shall be at a optional sub-cycle if specified
minimum cubic rate per minute equivalent to (2.3); sub-cycle performed during
10 times the volume of the chamber any 5 of the first 9 cycles; humidity
0
temperature uncontrolled during sub-cycle
tolerance
±2 °C (±3.6 °F) voltage applied as specified in 2.4
unless otherwise
specified
HBK073 0 5 10 15 20 25
time [h]
www.yageo.com
Sep 03, 2004 V.2
Product specification 10
10
Chip Resistor Surface Mount RC SERIES 1206 (Pb Free)
REVISION HISTORY
REVISION DATE CHANGE NOTIFICATION DESCRIPTION
Version 2 Sep 03, 2004 - - New datasheet for 1206 thick film 1% and 5% with lead-free terminations
- Replace the 1206 part of pdf files: RC01_11_21_31_5, RC02_12_22_32_10,
and HRC01_5_4
- Test method and procedure updated
- PE tape added (paper tape will be replaced by PE tape)
- High ohmic products combined into standard products.
www.yageo.com
Sep 03, 2004 V.2