Professional Documents
Culture Documents
AN007-Power Loss and Efficiency Calculation of Resonant LLC Converter
AN007-Power Loss and Efficiency Calculation of Resonant LLC Converter
© Altair Engineering, Inc. All Rights Reserved. / altair.com / Nasdaq: ALTR / Contact Us
Altair PSIM Application Note / Power Loss and Efficiency Calculation of Resonant LLC Converter
1. Introduction
Resonant LLC resonant converters have attracted much attention in recent years due to the soft-
switching characteristics over a wide load-line range, higher peak efficiency, and lower EMI footprint.
A resonant LLC converter can also offer high power density as the resonant components can be
incorporated into the magnetics, and higher switching frequency operation can be used due to
negligible switching losses and low EMI noises. However, optimal design and power loss calculation
of resonant LLC converter is a challenging task.
The Power Supply Design Suite (PSDS) in PSIM provides the design tool for fast analysis and
optimization of resonant converters with accuracy and precision to address the above issues and
design challenges. The Thermal Module in PSIM can help us to calculate power losses of
semiconductor devices quickly with information from manufacturer device datasheets.
In this application note, we will first use PSDS to design the resonant LLC converter with ideal
switching devices. Then we will replace the ideal devices with the Thermal Module devices based
on manufacturer’s datasheet to determine the total power loss, which includes the conduction and
switching losses.
2. System Specifications
The selected resonant LLC converter in this application note has following specifications:
Vin_rated = 390V; Vin_min = 375V; Vin_max =405V
Vo_rated = 12V
Po_rated = 500W
f_res = 125 kHz
• Using PSDS to perform resonant tank parameter optimization with the selected quality factor,
magnetics ratio, frequency-range, and with ideal switching devices.
• Using the Thermal Module to add the selected MOSFET and diode devices into the Device
Database.
• Running the simulation with Thermal Module devices to determine the power loss of the
converter.
© Altair Engineering, Inc. All Rights Reserved. / altair.com / Nasdaq: ALTR / Contact Us 2
Altair PSIM Application Note / Power Loss and Efficiency Calculation of Resonant LLC Converter
Steady
State
Solver
Design
Curve Tool
Parameter
Panel
Figure 1: The unpacked full-bridge resonant LLC converter template from the Design Suite
The Parameter Panel on the left of the schematic screen allows the user to input the design
specifications, launch the Steady State Solver Tool and the Design Curve Tool. The parameter file
on the left of the circuit stores the calculated parameter values of the resonant LLC converter.
For this application, we have selected Q_rated as 0.4 and K_ind as 4 to achieve the optimal LLC
converter design with narrower frequency variation range for the given line and load conditions.
The resonant tank component values of Ls, Cs, Lm are calculated as:
Ls = (Q_rated*Ro_rated_pri)/(2*pi*f_res) = 154.92 uH
Cs = 1/(2*pi*f_res*Q_rated*Ro_rated_pri) = 10.463836 nF
Lm = K_ind*Ls = 619.72 uH
where Ro_rated_pri is the rated value of output load resistance referred to the primary side.
The required relative frequency variation factor (K_rel_freq) can be determined as 0.94 to 1.06 based
on the gain requirements. However, considering the overloading factor, voltage drop across the
output diodes, resistance of the transformer, and the dead-time of the switches, the K_rel_freq is
selected as 0.80 to 1.1.
© Altair Engineering, Inc. All Rights Reserved. / altair.com / Nasdaq: ALTR / Contact Us 3
Altair PSIM Application Note / Power Loss and Efficiency Calculation of Resonant LLC Converter
3. Enter the basic information such as the part number, package, and maximum ratings from
datasheet as shown below:
4. Enter the electrical characteristics information (shown below in left) based on the datasheet
(shown below in the right).
© Altair Engineering, Inc. All Rights Reserved. / altair.com / Nasdaq: ALTR / Contact Us 4
Altair PSIM Application Note / Power Loss and Efficiency Calculation of Resonant LLC Converter
5. Enter the electrical characteristics for the antiparallel diode as shown below:
Next we will use the Curve Capture Tool to import the electrical characteristics curves of the
antiparallel diode from the datasheet.
First, click on the Edit button of the “Vd vs. IF” characteristics. A window for the Curve Capture Tool
will be displayed.
Click on Add Curve, use the Graph Wizard button at the upper left corner to capture the curve at
one operating temperature with the procedures listed below:
1. Display the graph of “Vd vs. IF” characteristics from the datasheet on the screen. Click on the
Print Screen key (PrtSc) to copy the screen to the clipboard.
2. Click on the forward green arrow of the Graph Wizard. The image in the clipboard will be
copied into the dialog window as shown below:
© Altair Engineering, Inc. All Rights Reserved. / altair.com / Nasdaq: ALTR / Contact Us 5
Altair PSIM Application Note / Power Loss and Efficiency Calculation of Resonant LLC Converter
3. Position the image properly within the window so that the complete graph is in full view. Click
on the forward arrow. Define the border of the graph by left-clicking on the graph's origin
(lower-left corner), and then move the cursor to the opposite corner (upper right corner) and
left-click. Right-click to zoom in for easier cursor placement. After this, a blue frame will be
superimposed on top of the original graph frame as shown below:
4. Click on the forward arrow. Check if the x-axis and y-axis definitions are correct. By default,
the x-axis is IF, and the y-axis is Vd. But if the x-axis is Vd, and the y-axis is IF in the datasheet.
We need to check the “swap X/Y axes” box to match the datasheet. Enter X0=0, Xmax=2,
Y0=0, Ymax=100. Input the junction temperature Tj=25 for the 25oC curve. The dialog
window is shown below:
© Altair Engineering, Inc. All Rights Reserved. / altair.com / Nasdaq: ALTR / Contact Us 6
Altair PSIM Application Note / Power Loss and Efficiency Calculation of Resonant LLC Converter
5. Click on the forward arrow. Starting from the origin, left click on top of the 25oC curve to
capture the data point. Right-click to zoom in for easier cursor placement. As you click along
the curve, a red curve will be drawn, indicating the data points captured. The dialog window
is shown below.
6. Click on the forward arrow, and the capture process will be completed. The dialog window of
captured curve for Tj=25oC is shown below.
© Altair Engineering, Inc. All Rights Reserved. / altair.com / Nasdaq: ALTR / Contact Us 7
Altair PSIM Application Note / Power Loss and Efficiency Calculation of Resonant LLC Converter
7. Click on the ‘Add Curve’ button to add a new curve. Repeat above steps to capture a curve
for the other operating/junction temperature.
Figure 2 below shows the device in the PcdEditor after this MOSFET model has been added into the
device file “IPP60R099CP.dev”. The electrical characteristics curves of the antiparallel diode at
different junction temperatures (25oC and 150oC) are shown in Figure 3.
© Altair Engineering, Inc. All Rights Reserved. / altair.com / Nasdaq: ALTR / Contact Us 8
Altair PSIM Application Note / Power Loss and Efficiency Calculation of Resonant LLC Converter
© Altair Engineering, Inc. All Rights Reserved. / altair.com / Nasdaq: ALTR / Contact Us 2
Altair PSIM Application Note / Power Loss and Efficiency Calculation of Resonant LLC Converter
© Altair Engineering, Inc. All Rights Reserved. / altair.com / Nasdaq: ALTR / Contact Us 3
Altair PSIM Application Note / Power Loss and Efficiency Calculation of Resonant LLC Converter
We can now select the thermal models of newly added MOSFET and Diode.
In PSIM, select Elements >> Power >> Thermal Module >> MOSFET (database).
Place the discrete MOSFET element on the schematic. Double click on the MOSFET element to
open the property dialog window. Click on the Browser button next to the “Device” input field and
choose the device “IPP60R099CP” as shown in Figure 6.
Figure 6: The MOSFET “Device” input field and path to choose the device “IPP60R099CP”
Similarly, select Elements >> Power >> Thermal Module >> Diode (database).
Place the discrete diode element on the schematic. Double click on the diode element to open the
property dialog window. Click on the Browser button next to the “Device” input field and choose the
device “STPS40L45C” as shown in Figure 7.
Figure 7: The diode “Device” input field and path to choose the device “STPS40L45C”
Figure 8 shows the revised resonant LLC converter schematic with IPP60R099CP and STPS40L45C
thermal devices.
The schematic file “Resonant LLC – power loss calculation.psimsch” can be found in the “simu”
subfolder of this application note folder.
© Altair Engineering, Inc. All Rights Reserved. / altair.com / Nasdaq: ALTR / Contact Us 4
Altair PSIM Application Note / Power Loss and Efficiency Calculation of Resonant LLC Converter
Figure 8: Resonant LLC converter schematic with MOSFET IPP60R099CP and diode
STPS40L45C
© Altair Engineering, Inc. All Rights Reserved. / altair.com / Nasdaq: ALTR / Contact Us 5
Altair PSIM Application Note / Power Loss and Efficiency Calculation of Resonant LLC Converter
Figure 10: Efficiency vs. the load current percentage at different input voltages
© Altair Engineering, Inc. All Rights Reserved. / altair.com / Nasdaq: ALTR / Contact Us 6
Altair PSIM Application Note / Power Loss and Efficiency Calculation of Resonant LLC Converter
4. Conclusion
This tutorial shows that a resonant LLC converter can be quickly designed using the Power Supply
Design Suite. Furthermore, with the Thermal Module in PSIM, users can select specific switch
devices and calculate the losses and the junction temperatures of the devices as well as the
efficiency of the whole converter easily.
© Altair Engineering, Inc. All Rights Reserved. / altair.com / Nasdaq: ALTR / Contact Us 7