Professional Documents
Culture Documents
MMS6
Rewindable, submersible motors and accessories
50/60 Hz
MMS6
4. Construction 9
Material specification 9
Pump connection 10
Shaft and radial bearing 10
Shaft seal 10
Rotor 10
Stator 10
Thrust bearing 11
Upthrust bearing 11
Diaphragm 11
Motor liquid 11
5. Technical data 12
MMS6 (-N, -R) 12
6. Electrical data 14
7. Wiring diagram 21
Wiring diagram 21
8. Accessories 22
CUE frequency converter 22
MP 204 25
G100 gateway for communication with Grundfos
products 27
Cable termination kit, type KM 29
Mastik for flat cables 29
Cable termination kit, types M0 to M6 30
Submersible drop cable 30
Zinc anodes 31
Flow sleeves 31
Pt100 sensor 32
Pt1000 sensor 34
9. Cable sizing 36
Drop cables 36
Cable sizing 37
2
MMS6
1
1. General description
General description
MMS6 rewindable motors
Grundfos MMS6 motors are 6" rewindable,
submersible motors, available in sizes from 5.5 kW to
37 kW.
Three material versions are available:
• A cast-iron version of EN-JL1040.
• For aggressive liquids with a moderate content of
salt, an N-version of stainless steel DIN/EN 1.4401
(AISI 316) is available.
• For aggressive liquids with a higher salt content
than that of seawater and for temperatures above
15 °C, we recommend the R-version of stainless
steel DIN/EN 1.4539 (AISI 904L).
MMS6 submersible motors are designed according to
market standards. All motors are designed to fit pump
ends manufactured according to NEMA standards.
The motors are ideally suited for water supply pumps
for irrigation, groundwater regulation, pressure
boosting, industrial water transfer and similar
applications. MMS6 motors comply with the same
standards as Grundfos MS motors and can therefore
be fitted to all Grundfos SP pumps without adapters.
GrA4575
The motor production is in the hands of experts with
many years of experience within the manufacture of
motors. In order to make the time of delivery as short Fig. 1 MMS6 motor
as possible, components are manufactured for stock,
enabling rapid assembly of a few basic components
into the finished motor.
Rewindable motors
The rewindable motor design means low costs of The two-pole MMS6 motors are easily rewound.
repair of the motor in case of damage. The rewindable The stator windings are made of a special water-proof
submersible motor technology reduces the risk of hot wire of pure electrolytic copper sheathed with special
spots in the motor as the liquid inside has a uniform non-hydroscopic thermoplastic material.
contact with active parts. The motor is filled with motor The high dielectric strength properties of this material
liquid ensuring sufficient lubrication of radial bearings. allow direct contact between the windings and the
Moreover, as motors can be rewound locally, liquid for efficient cooling of the windings.
unnecessary time for transportation of the motor can
be avoided and possible periods of downtime reduced High motor efficiency
to a minimum. The design of the motor, based on few
basic components, also facilitates service and repair of The complete motor range offered by Grundfos is
the motor. characterised by high efficiency contributing to
Fitted with a sturdy Michell thrust bearing, which also improved economy of the total pump system.
functions as an upthrust bearing, all motors offer
reliable operation. Overtemperature protection
In order to achieve maximum protection of the motor
For protection against overtemperature, Grundfos
against burnout, all motors can be fitted with a Pt100
offers Pt100 and Pt1000 temperature sensors as an
or Pt1000 sensor. Combined with a relay and an
optional extra.
optional Grundfos CUE frequency converter or MP 204
motor protector, the Pt100/Pt1000 sensor provides The Pt100 and Pt1000 sensors are fitted in the motor
optimum motor protection. See Accessories, page 22. and connected via a relay, which can be connected to
the MP 204 motor protector. The temperature can be
monitored by means of an MP 204, a CU 220, a
PR5714 or a CUE.
If the temperature becomes too high, the motor will be
cut out. See Accessories, page 22.
3
1 MMS6
Motor power
Motor type Thrust* Upthrust
[kW] (hp)
Operation
Frequency of starts
4
MMS6
2
2. Identification
Identification
Nameplate
3 2 1 13 14 15 16
4
5 MMS6T30 No. 96879380 Model A SN 00000123 PC P80842 17
Phase Voltage Frequency P2 P2 SF Max. SF. C. Cos n
6 [-] [V] [Hz] [kW] [hp] [-] [A] [-] [min-1]
7 3 380 50 37 50 1.00 82.5 0.85 2835
3 400 50 37 50 1.00 80.5 0.81 2860 18
3 415 50 37 50 1.00 80.9 0.77 2870
8 3 460 60 37 50 1.15 78.2 0.82 3455
19
Liquid t max. 30°C at 0.5 m/s -80°F at 16 ft/s Connection DOL Weight: 125 kg/ 276 lb
9 20
Duty S1 PT100 pmax. 60 bar kVA code E IP68
10000002423
10 MADE IN ITALY
IEC 134
11
12
5
2 MMS6
Type key
Identification
Type range
(Motor Submersible)
Material
Cast iron EN JL 1040
N Stainless steel EN 1.4401 (AISI 316)
R Stainless steel EN 1.4539 (AISI 904L)
Rubber parts
NBR
E FKM
Shaft seal
Ceramics/carbon
S SiC/SiC
Motor liquid
SML-3
D Demineralised water
6
MMS6
3
3. Operating conditions
Operating conditions
Cooling Liquid temperature
The cooling of the motor depends on the temperature Motors with PVC windings can operate at liquid
and the flow velocity of the pumped liquid past the temperatures up to 30 °C without derating.
motor. When operating in liquids at temperatures from 20 °C
To ensure sufficient cooling, the values for maximum to 43 °C, the motor must be derated according to the
temperature of the pumped liquid and its flow velocity curve below.
must be kept.
We recommend always to ensure a minimum cooling 1.1
flow of 0.15 m/s. 1.0
v=
0.9 0.8
Derating factor
m/s
Free convection 0.8
v=
0.5
m /s
Free convection is achieved when the diameter of the 0.7
v=
0.2
borehole is at least 2" (~ 50 mm) bigger than the outer m/
s
Q min 1.1
v = --------------------------------------------------- m/s
2 2
2826 D i – d A 1.0
v=
0.9
Derating factor
0.8
Required data: v= m/
0.8 0 .5 s
v=
Qmin.: Flow rate [m3/h] 0.7 0.2
m/
s
Di: Borehole diameter [m] m/
s
1.1
Dborehole
1.0
0.9 v=
Derating factor
0.6
Flow velocity past motor PE2/PA windings PVC windings 0.5
[m/s] [°C] [°C]*
44 46 48 50 52 54 56 58 60 62 64 66
0.2 45 30 Temperature [°C]
0.5 50 35
Fig. 6 PE2/PA windings, 5.5 to 37 kW
* The maximum liquid temperature of 37 kW motors is 5 °C lower.
Operating pressure
Maximum 60 bar.
7
3 MMS6
Winding temperature
Operating conditions
Voltage quality
The required voltage quality for Grundfos MMS6
submersible motors, measured at the motor terminals,
is - 10 %/+ 6 % of the rated voltage during continuous
operation (including variations in the supply voltage
and losses in cables).
Enclosure class
IP68.
8
MMS6
4
4. Construction
Construction
Material specification
Cast-iron version
Version
EN EN EN
202 Shaft with rotor Stainless steel 1.4301 1.4401 1.4462
Thrust Hardened steel/
1.4125 1.4125 1.4125
203/ bearing/rotating stainless steel
206 thrust bearing
part Ceramic/carbon - - -
204 Radial bearing Carbon - - -
Cast iron/
205 NEMA flange JL1040 1.4408 1.4517
stainless steel
208a Thrust ring Stainless steel 1.4016 1.4016 1.4016
Thrust bearing
208b Stainless steel 1.4016 1.4016 1.4016
support
212 Diaphragm EPDM - - -
Cast iron/
213 End cover JL1040 1.4408 1.4517
stainless steel
216 Lock nut Steel, BN1235 - - -
216a Washer Stainless steel 1.4301 1.4301 1.4301
Thrust bearing
219 Stainless steel 1.4308 1.4308 1.4517
housing
Stator with
221 Stainless steel 1.4306 1.4404 1.4539
sleeve
222b O-ring Fibronit - - -
223b Plug Stainless steel 1.4401 1.4401 1.4539
224 O-ring NBR - - -
Shaft seal Cast iron/
226 JL1040 1.4401 1.4539
housing stainless steel
Shaft seal, Ceramic/carbon ● ● -
226a
stationary part SiC/SiC ● ● ●
Shaft seal,
226b SiC - - -
rotating part
229 Sand shield FKM - - -
231 O-ring NBR - - -
232 Lip seal ring FKM - - -
Intermediate Cast iron/
235 JL1040 1.4408 1.4517
housing stainless steel
Bearing Cast iron/
236 JL1040 1.4408 1.4517
housing, lower stainless steel
Hexagon socket
236a Steel - - -
head screw
242 Upthrust spacer PP - - - 223b
247 Screw 1.4401 1.4401 1.4539
Motor cable EPDM - - -
TM04 4951 2309
9
4 MMS6
The motor has connections according to the NEMA The stator is a wet-wound design in stainless steel to
standard MG 1-18.413. protect the motor, even in corrosive water. The stator
The cable outlet of motors for star-delta starting is design allows complete access to the winding for easy
displaced by 90 °. maintenance and rewinding. The construction of the
laminations minimises operating losses and improves
motor performance.
The motor end shield is screwed onto the stator.
A suitable centring ensures alignment of rotor and
stator.
Shaft seal
The mechanical shaft seal is available in two variants:
ceramic/carbon and SiC/SiC. SiC/SiC is according to
DIN 24960.
The highly wear-resistant and durable material
ensures tightness and thus limited replacement of the
motor liquid. This is important when the pumped liquid
contains sand.
Together with the shaft seal housing, the sand shield
forms a labyrinth seal, which during normal operating
conditions prevents sand particles from entering the
shaft seal.
The double shaft seal consists of a rubber lip seal and
a mechanical seal. The double shaft seal protects the
motor from abrasive particles.
Rotor
The rotor is a squirrel-cage rotor with copper bars
brazed to the short-circuit rings with a silver alloy.
The rotor is dynamically balanced for smooth and
vibration-free operation.
10
MMS6
4
Thrust bearing Rotating bearing part
Construction
The Michell/Kingsbury type of water-lubricated thrust To prolong the bearing life, the rotating part with a
bearing is very simple and most efficient. larger surface is made of soft carbon material.
The carbon disk is polished for optimum surface finish.
The thrust capacity of the bearings is in accordance
with NEMA standards for submersible motors, where Stationary bearing part
these are applicable. See fig. 9. The stationary part is made of tempered stainless
steel. This segmented component is cast as a
one-in-all cost-effective unit. By design, each pad
becomes flexible as required for good functionality.
The segmented surface is finally polished to a
specially designed shape.
Upthrust bearing
The PP upthrust spacers above the rotating bearing
part prevent motor damage during transportation or in
case of upthrust.
The upthrust bearing is an integrated part of the thrust
bearing.
Diaphragm
The diaphragm is fitted between the stator and the
motor end shield. The diaphragm ensures that volume
changes due to temperature changes can be
accommodated by the motor liquid without effecting
the pumped liquid.
Motor liquid
The motor is factory-filled with Grundfos motor liquid,
type SML-3, which is frost-proof down to -20 °C.
Corrosion protection
The motor liquid protects metals and alloys in the
equipment against all types of corrosion. The
combination of low toxicity and FDA-approved
ingredients with a high level of corrosion protection
makes Grundfos motor liquid unique in the market.
The anti-corrosion performance is demonstrated
according to ASTM D 1384.
TM04 4952 2309
11
5 MMS6
5. Technical data
Technical data
12
MMS6
5
Cables Cable length:
Technical data
The MMS6 motors are connected by means of four • 5.5 and 26 kW: 5 m
single-core cables, approved for drinking water. • 30 and 37 kW: 8 m.
All cables are round. Note: Sizing of the motor cable requires that it is
The cable outlet of motors for star-delta starting is submerged in water. For longer cables and cable
displaced by 90 °. connection for extension, see 8. Accessories, page 22.
Being an integrated part of the motor, the motor cable The MMS6 motors have an integrated earth cable.
cannot be fitted or removed once the motor is
assembled.
Cross-section [mm 2]
[kW] [hp] 4x1 8x1 4x1 8x1 4x1 8x1 4x1 8x1 4x1 8x1
5.5 7.5 - - 6 - 6 - - - - -
7.5 10 - - 6 - 6 - - - - -
9.2 12 - - 6 - 6 - - - - -
11 15 - - 6 - 6 6 - - - -
13 18 - - 6 - 6 6 - - - -
15 20 - - 6 - 6 6 - - - -
18.5 25 - - 10 - 6 6 - - - -
22 30 - - 10 - 6 6 - - - -
26 35 - 6 10 - 6 6 - 6 - -
30 40 - 6 16 - 10 6 - 6 10 -
37 50 - - - 10 10 6 - - 10 -
Cross-section [mm2]
[kW] [hp] 4x1 8x1 4x1 8x1 4x1 8x1 4x1 8x1
5.5 7.5 - - - 6 - 6 -
7.5 10 6 - - 6 - 6 -
9.2 12 6 - 6 - 6 - 6 -
11 15 6 - 6 - 6 - 6 -
13 18 6 - 6 - 6 - 6 -
15 20 6 - 6 - 6 - 6 -
18.5 25 6 - 6 - 10 - 6 -
22 30 6 - 6 - 10 - 6 -
26 35 6 - 6 - 16 - 10 -
30 40 10 - 10 - 16 - 10 -
37 50 10 - 10 - - 10 10 -
Outer dimensions
13
6 MMS6
6. Electrical data
Electrical data
Abbreviation Description
T-code T-code refers to the maximum liquid temperature. See Type key, page 6.
BT Breakdown Torque
LRT Locked-Rotor Torque
LRC Locked-Rotor Current
3 x 220 V, 50 Hz
14
MMS6
6
3 x 230 V, 50 Hz
Electrical data
Motor Cos φ Efficiency (η)
I1/1 n BT LRT LRC Thrust kVA code
P2 50 % 75 % 100 % 50 % 75 % 100 %
T-code
[kW] [A] [%] [%] [%] [min-1] [%] [%] [%] [kN]
T35 5.5 25.0 0.61 0.72 0.78 71 75 76 2860 190 90 350 27.5 -
T35 7.5 33.5 0.59 0.71 0.78 72 76 77 2860 200 90 350 27.5 -
T35 9.2 40.5 0.59 0.71 0.78 74 77 78 2860 200 90 360 27.5 -
T35 11 50.0 0.53 0.66 0.74 74 78 79 2870 230 110 380 27.5 -
T35 13 56.0 0.57 0.69 0.77 77 80 80 2860 220 110 390 27.5 -
T35 15 62.5 0.58 0.71 0.79 79 82 82 2860 240 120 430 27.5 -
T35 18.5 75.0 0.61 0.75 0.81 80 82 82 2850 230 120 420 27.5 -
T35 22 87.0 0.61 0.74 0.81 82 84 83 2870 280 198 530 27.5 -
T35 26 106 0.57 0.70 0.78 81 83 83 2880 260 226 560 27.5 -
T35 30 118 0.63 0.76 0.82 82 83 82 2860 230 166 475 27.5 -
T30 37 148 0.59 0.72 0.81 82 84 83 2860 300 212 540 27.5 -
T50 5.5 25.0 0.63 0.73 0.79 69 73 73 2860 180 80 330 27.5 -
T50 7.5 33.5 0.61 0.73 0.80 71 75 75 2850 190 90 340 27.5 -
T50 9.2 40.5 0.60 0.72 0.80 73 76 76 2850 190 90 350 27.5 -
T50 11 49.5 0.55 0.69 0.77 72 76 77 2860 210 100 370 27.5 -
T50 13 56.0 0.59 0.72 0.80 75 78 78 2850 210 100 370 27.5 -
T50 15 62.5 0.60 0.73 0.80 77 80 80 2860 230 120 410 27.5 -
T50 18.5 75.0 0.63 0.75 0.82 79 81 81 2850 220 120 410 27.5 -
T50 22 87.5 0.63 0.75 0.82 82 83 82 2870 270 188 515 27.5 -
T50 26 106 0.57 0.71 0.79 80 83 82 2880 250 216 545 27.5 -
T50 30 118 0.64 0.77 0.83 81 83 81 2850 224 160 465 27.5 -
T50 37 148 0.61 0.75 0.83 80 82 81 2850 270 186 505 27.5 -
3 x 380 V, 50 Hz
15
6 MMS6
3 x 400 V, 50 Hz
Electrical data
3 x 415 V, 50 Hz
16
MMS6
6
3 x 460 V, 60 Hz, SF 1.15
Electrical data
Motor Current Motor Cos φ Efficiency (η)
kVA
n BT LRT LRC Thrust
Full load Full Max. Max. load (P1) Full Full Max. code
T-code
Max. load
(P2) load load incl. SF load load load
[kW] [hp] [A] [A] [kW] [%] [%] [min-1] [%] [%] [%] [kN] [lbf]
T35 5.5 7.5 13.0 14.4 8.50 0.76 0.78 74 75 3460 200 80 340 27.5 6182 F
T35 7.5 10 17.2 19.0 11.4 0.76 0.78 76 77 3460 200 80 350 27.5 6182 F
T35 9.2 12 20.2 22.6 13.6 0.78 0.80 78 78 3440 190 80 350 27.5 6182 E
T35 11 15 24.2 27.0 16.2 0.77 0.80 78 78 3450 210 90 370 27.5 6182 F
T35 13 20 31.0 31.0 21.8 0.80 0.80 80 80 3450 220 100 390 27.5 6182 E
T35 15 20 32.0 35.5 21.8 0.78 0.81 80 80 3460 230 110 430 27.5 6182 G
T35 18.5 25 38.0 42.5 26.0 0.79 0.81 82 82 3450 260 120 460 27.5 6182 E
T35 22 30 45.0 47.5 30.0 0.77 0.79 84 84 3490 320 220 615 27.5 6182 J
T35 26 35 53.0 59.0 35.5 0.77 0.80 84 84 3470 270 222 605 27.5 6182 J
T35 30 40 58.8 66.1 41.0 0.80 0.82 85 84 3460 255 166 520 27.5 6182 H
T30 37 50 73.0 82.0 51.0 0.80 0.82 84 84 3450 285 176 530 27.5 6182 H
T50 5.5 7.5 13.0 14.6 8.80 0.78 0.79 72 73 3440 190 80 330 27.5 6182 E
T50 7.5 10 17.2 19.2 11.6 0.77 0.80 75 75 3450 190 80 350 27.5 6182 F
T50 9.2 12 20.2 22.8 14.0 0.79 0.81 77 76 3440 190 80 340 27.5 6182 E
T50 11 15 24.4 27.0 16.4 0.77 0.80 78 78 3450 210 90 370 27.5 6182 F
T50 13 18 28.5 32.0 19.2 0.77 0.80 78 78 3450 210 100 390 27.5 6182 F
T50 15 20 32.0 35.5 21.8 0.78 0.81 80 80 3460 230 110 430 27.5 6182 G
T50 18.5 25 38.0 42.5 26.5 0.80 0.82 81 81 3450 230 110 430 27.5 6182 F
T50 22 30 45.0 47.5 30.5 0.78 0.80 83 83 3480 320 206 595 27.5 6182 J
T50 26 35 53.0 59.0 36.5 0.79 0.82 83 82 3470 250 200 575 27.5 6182 J
T50 30 40 59.0 67.0 42.0 0.81 0.83 83 82 3450 240 156 500 27.5 6182 G
T50 37 50 73.0 82.0 51.5 0.81 0.83 83 83 3450 275 168 520 27.5 6182 H
17
6 MMS6
3 x 460 V, 50 Hz
3 x 500 V, 50 Hz
18
MMS6
6
3 x 525 V, 50 Hz
Electrical data
Motor Cos φ Efficiency (η)
I1/1 n BT LRT LRC Thrust kVA code
P2 50 % 75 % 100 % 50 % 75 % 100 %
T-code
[kW] [A] [%] [%] [%] [min-1] [%] [%] [%] [kN]
T50 9.2 18.6 0.55 0.69 0.77 70 74 75 2870 210 100 370 27.5 -
T50 11 21.4 0.57 0.70 0.78 72 76 77 2860 210 100 370 27.5 -
T50 13 25.0 0.55 0.69 0.77 73 77 78 2860 220 110 390 27.5 -
T50 15 28.0 0.58 0.71 0.79 76 79 79 2860 230 120 420 27.5 -
T50 18.5 34.0 0.58 0.71 0.80 76 79 79 2860 230 120 420 27.5 -
T50 22 38.5 0.63 0.75 0.82 81 82 81 2870 270 190 515 27.5 -
T50 26 46.0 0.60 0.73 0.81 80 82 81 2870 240 206 535 27.5 -
T50 30 53.5 0.59 0.73 0.82 79 81 80 2860 234 166 475 27.5 -
T50 37 66.0 0.57 0.72 0.81 79 81 81 2860 300 208 530 27.5 -
Max. load
(P2) load load incl. SF load load load
[kW] [hp] [A] [A] [kW] [%] [%] [min-1] [%] [%] [%] [kN] [lbf]
T50 9.2 12 16.4 18.4 14.2 0.78 0.81 76 76 3450 190 80 350 27.5 6182 E
T50 11 15 19.0 21.4 16.6 0.80 0.82 77 77 3440 190 80 350 27.5 6182 E
T50 13 18 22.0 24.8 19.2 0.80 0.82 79 78 3440 200 90 370 27.5 6182 E
T50 15 20 24.6 28.0 21.8 0.81 0.83 80 79 3440 210 100 400 27.5 6182 F
T50 18.5 25 30.0 34.0 27.0 0.82 0.83 80 80 3440 210 100 410 27.5 6182 F
T50 22 30 34.0 39.0 31.0 0.82 0.84 82 81 3440 248 162 495 27.5 6182 G
T50 26 35 40.5 46.5 37.0 0.82 0.84 82 81 3450 222 178 525 27.5 6182 H
T50 30 40 47.0 53.5 43.0 0.82 0.84 81 80 3440 218 142 465 27.5 6182 H
T50 37 50 57.0 65.0 52.5 0.83 0.85 82 81 3440 280 178 530 27.5 6182 H
Max. load
(P2) load load incl. SF load load load
[kW] [hp] [A] [A] [kW] [%] [%] [min-1] [%] [%] [%] [kN] [lbf]
T35 5.5 7.5 27.0 30.5 8.55 0.77 0.79 74 74 3450 190 80 340 27.5 6182 F
T35 7.5 10 36.0 40.0 11.4 0.76 0.79 76 76 3450 200 80 350 27.5 6182 F
T35 9.2 12 42.0 47.0 13.6 0.78 0.80 78 78 3440 190 80 350 27.5 6182 F
T35 11 15 50.5 56.0 15.8 0.76 0.79 80 80 3450 210 90 370 27.5 6182 G
T35 13 18 57.5 64.5 18.6 0.78 0.80 81 81 3440 210 90 380 27.5 6182 F
T35 15 20 65.5 73.5 21.2 0.78 0.81 82 82 3450 230 110 420 27.5 6182 G
T35 18.5 25 78.5 88.5 26.0 0.81 0.82 82 81 3440 220 100 410 27.5 6182 F
T35 22 30 90.5 102 30.5 0.81 0.83 83 83 3460 265 174 525 27.5 6182 H
T35 26 35 106 120 35.5 0.81 0.83 84 84 3460 228 182 535 27.5 6182 H
T35 30 40 120 138 41.0 0.82 0.84 84 84 3440 224 148 470 27.5 6182 G
T30 37 50 152 172 51.0 0.81 0.84 84 83 3450 280 182 545 27.5 6182 H
T50 5.5 7.5 27.0 30.5 8.70 0.78 0.80 72 72 3440 180 70 330 27.5 6182 F
T50 7.5 10 36.0 40.5 11.6 0.77 0.80 75 75 3450 190 80 340 27.5 6182 F
T50 9.2 12 42.0 48.0 13.8 0.80 0.81 76 76 3.430 180 80 330 27.5 6182 F
T50 11 15 50.5 56.5 16.2 0.78 0.80 78 78 3450 200 90 360 27.5 6182 F
T50 13 18 57.5 64.5 18.8 0.79 0.82 80 79 3440 200 90 370 27.5 6182 F
T50 15 20 65.5 73.5 21.4 0.79 0.81 81 81 3450 230 100 420 27.5 6182 G
T50 18.5 25 79.0 89.0 26.5 0.81 0.83 81 80 3440 210 100 400 27.5 6182 F
T50 22 30 90.5 104 30.5 0.82 0.83 83 82 3450 260 166 515 27.5 6182 H
T50 26 35 106 122 36.5 0.82 0.84 82 81 3450 218 172 515 27.5 6182 G
T50 30 40 122 140 42.0 0.83 0.85 83 81 3.430 208 136 445 27.5 6182 F
T50 37 50 152 172 51.5 0.82 0.84 83 82 3450 275 174 530 27.5 6182 G
19
6 MMS6
Max. load
(P2) load load incl. SF load load load
[kW] [hp] [A] [A] [kW] [%] [%] [min-1] [%] [%] [%] [kN] [lbf]
T35 5.5 7.5 26.5 29.5 8.55 0.74 0.77 74 75 3470 210 80 360 27.5 6182 F
T35 7.5 10 36.0 39.5 11.4 0.72 0.76 76 77 3470 220 90 370 27.5 6182 F
T35 9.2 12 42.0 46.0 13.6 0.75 0.78 78 79 3460 210 90 370 27.5 6182 F
T35 11 15 51.0 56.0 15.8 0.72 0.75 80 80 3470 230 100 390 27.5 6182 G
T35 13 18 57.5 63.5 18.6 0.74 0.78 81 81 3460 230 100 400 27.5 6182 F
T35 15 20 66.5 73.0 21.2 0.74 0.77 81 82 3470 260 120 450 27.5 6182 G
T35 18.5 25 78.5 87.0 26.0 0.77 0.80 82 82 3460 240 110 440 27.5 6182 F
T35 22 30 90.0 100 30.5 0.78 0.81 84 83 3470 295 192 565 27.5 6182 H
T35 26 35 106 118 35.5 0.78 0.81 84 84 3470 250 202 575 27.5 6182 H
T35 30 40 118 132 41.0 0.80 0.82 85 84 3460 248 162 510 27.5 6182 G
T30 37 50 154 170 51.0 0.77 0.81 84 84 3470 310 200 575 27.5 6182 H
T50 5.5 7.5 26.5 29.5 8.70 0.76 0.78 73 73 3460 200 80 350 27.5 6182 F
T50 7.5 10 36.0 39.5 11.6 0.74 0.77 75 75 3470 210 90 370 27.5 6182 F
T50 9.2 12 41.5 46.5 13.8 0.77 0.79 77 77 3450 200 80 360 27.5 6182 F
T50 11 15 51.0 56.0 16.2 0.73 0.77 78 79 3460 220 90 390 27.5 6182 F
T50 13 18 57.5 63.5 18.8 0.76 0.79 80 80 3450 220 100 390 27.5 6182 F
T50 15 20 66.5 73.0 21.4 0.75 0.78 81 81 3470 250 120 440 27.5 6182 G
T50 18.5 25 78.5 87.5 26.5 0.78 0.81 81 81 3460 230 110 430 27.5 6182 F
T50 22 30 90.0 100 30.5 0.78 0.81 83 83 3470 285 184 550 27.5 6182 H
T50 26 35 106 118 36.5 0.79 0.82 83 82 3470 242 190 555 27.5 6182 G
T50 30 40 118 134 42.0 0.81 0.83 83 82 3450 230 150 485 27.5 6182 F
T50 37 50 154 170 51.5 0.78 0.81 83 83 3460 305 192 560 27.5 6182 G
Max. load
(P2) load load incl. SF load load load
[kW] [hp] [A] [A] [kW] [%] [%] [min-1] [%] [%] [%] [kN] [lbf]
T35 5.5 7.5 15.6 17.4 8.55 0.77 0.79 74 75 3450 190 80 340 27.5 6182 E
T35 7.5 10 20.8 23.2 11.4 0.76 0.79 76 76 3450 200 80 350 27.5 6182 F
T35 9.2 12 24.2 27.0 13.6 0.78 0.80 78 78 3440 190 80 350 27.5 6182 E
T35 11 15 30.0 33.0 16.2 0.76 0.79 78 78 3450 210 90 380 27.5 6182 F
T35 13 18 34.5 38.0 19.0 0.77 0.79 79 80 3450 220 100 390 27.5 6182 F
T35 15 20 38.5 43.0 21.6 0.78 0.80 81 81 3460 240 110 430 27.5 6182 G
T35 18.5 25 45.5 51.0 26.0 0.79 0.82 83 82 3450 240 110 430 27.5 6182 F
T35 22 30 53.5 59.5 30.0 0.79 0.81 84 84 3470 295 196 570 27.5 6182 H
T35 26 35 61.5 69.5 35.5 0.80 0.82 85 84 3470 250 210 585 27.5 6182 J
T35 30 40 67.0 75.5 41.5 0.81 0.83 84 84 3450 238 156 495 27.5 6182 G
T30 37 50 88.5 99.0 51.0 0.80 0.82 84 84 3460 310 202 575 27.5 6182 H
T50 5.5 7.5 15.8 17.6 8.80 0.78 0.80 72 72 3440 180 70 330 27.5 6182 E
T50 7.5 10 20.8 23.2 11.6 0.77 0.80 75 75 3450 190 80 340 27.5 6182 E
T50 9.2 12 24.4 27.5 14.0 0.80 0.81 76 76 3430 180 80 340 27.5 6182 E
T50 11 15 30.0 33.0 16.6 0.78 0.80 77 77 3450 200 90 370 27.5 6182 F
T50 13 18 34.5 38.5 19.2 0.78 0.81 78 78 3450 210 90 380 27.5 6182 F
T50 15 20 38.5 43.0 21.8 0.79 0.81 80 80 3460 230 110 420 27.5 6182 G
T50 18.5 25 46.0 51.5 26.5 0.81 0.82 81 80 3440 220 100 420 27.5 6182 F
T50 22 30 53.5 60.0 30.5 0.80 0.82 83 83 3470 280 184 545 27.5 6182 H
T50 26 35 62.0 70.0 36.0 0.81 0.83 83 83 3460 238 194 555 27.5 6182 H
T50 30 40 70.0 80.0 41.5 0.82 0.83 84 83 3450 232 154 490 27.5 6182 G
T50 37 50 88.5 99.5 51.5 0.80 0.83 84 83 3460 300 194 560 27.5 6182 H
20
MMS6
7
7. Wiring diagram
Wiring diagram
Wiring diagram
The motors are available for both direct-on-line and
star-delta starting.
Motors wound for star-delta starting can also be
connected for direct-on-line starting.
Direct-on-line starting
PE L1 L2 L3
PE U V W
TM03 2099 3705
M
3
Fig. 10 Motors wound for direct-on-line starting
Star-delta starting
PE L1 L2 L3
W2 U2 V2
TM03 2100 3705
PE U1 V1 W1
M
3
PE L1 L2 L3
W2 U2 V2
TM03 2101 3511
PEU1 V1 W1
M
3
21
8 MMS6
8. Accessories
Accessories
Power [kW]
Supply voltage
[V] 0.55 0.75 1.1 7.5 11 45 250
GrA4404
3 x 525-690
3 x 525-600
3 x 380-500
3 x 200-240 Fig. 13 CUE frequency converters
1 x 200-240 Functions
The CUE is available in two enclosure classes: The CUE has a wide range of pump-specific functions,
• IP20/21 such as
• IP54/55. • constant pressure
RFI filters • constant level
• constant flow rate
To meet the EMC requirements, the CUE comes with
the following types of built-in radio frequency • constant temperature
interference filter (RFI). • constant curve.
Features
Typical shaft
Voltage
[V]
power (P2) RFI filter type Application • Start-up guide
[kW]
The CUE incorporates an innovative start-up guide
1 x 200-240 1.1 - 7.5 C1 for the general setting of the CUE including the
3 x 200-240 0.75 - 45 C1
Residential setting of the correct direction of rotation.
areas
The start-up guide is started the first time when the
0.55 - 90 C1
CUE is connected to the power supply.
3 x 380-500 Residential
110 - 250 C2 areas/ • Check of direction of rotation.
industry • Duty/standby operation.
3 x 525-600 0.75 - 7.5 C3 • Dry-running protection.
Industry
3 x 525-690 11 - 25 C3 • Low-flow stop function.
22
MMS6
8
Inputs and outputs Sensors
Accessories
The CUE incorporates various inputs and outputs: The following sensors can be used in connection with
• 1 RS-485 GENIbus connection the CUE. All sensors are with 4-20 mA output signal.
• 1 analog input, 0-10 V, 0/4-20 mA • Pressure sensors, up to 25 bar
– external setpoint • temperature sensors
• 1 analog input, 0/4-20 mA • differential-pressure sensors
– sensor input, feedback sensor • differential-temperature sensors
• 1 analog output, 0-20 mA • flowmeters
• 4 digital inputs • potentiometer box for external setpoint setting.
– start/stop and three programmable inputs Gateways
• 2 signal relays (C/NO/NC) The CUE has a standard RS-485 GENIbus interface.
– programmable. Gateways to convert to other bus standards are
available as accessories.
Accessories for the CUE
The Grundfos CIU family (CIU = Communication
Grundfos offers various accessories for the CUE.
Interface Units) can convert from GENIbus to the most
MCB 114 sensor input module common fieldbuses in the world:
The MCB 114 offers additional analog inputs for the • CIU 100 converts from GENIbus to LonWorks
CUE: • CIU 150 converts from GENIbus to Profibus DP
• 1 analog input, 0/4-20 mA • CIU 200 converts from GENIbus to Modbus RTU
• 2 inputs for Pt100 and Pt1000 temperature sensors. • CIU 250 is a GSM modem which can send SMS
Output filters messages in case of alarms, etc.
Output filters are used primarily to protect the motor Control MPC
against overvoltage and increased operating The Control MPC is a multi-pump control system for
temperature. However, output filters can also be used the control of parallel-connected CUE pump solutions.
to reduce acoustic noise from the motor.
Use of output filters
Grundfos offers two types of output filter as
accessories for the CUE: The table below shows in which cases an output filter
is required and which type to use.
• dU/dt filters
The selection depends on these factors:
• sine-wave filters.
• pump type
Floor-mounting option • motor cable length
The CUE is as standard installed on the wall. • the required reduction of acoustic noise from the
The enclosures D1 and D2 can also be installed on the motor.
floor on a pedestal designed for that purpose.
For information about enclosures, see the Typical shaft dU/dt filter
Sine-wave
product-specific documentation for the CUE. Pump type filter
power (P2) [m]
[m]
IP21/NEMA1 option Up to 7.5 kW - 0-300
SP with 380 V motor
An IP20 enclosure can be upgraded to IP21/NEMA1 by and up 11 kW and up 0-150 150-300
using the IP21/NEMA1 option. The power terminals
(mains and motor) will be covered. The lengths stated apply to the motor cable.
23
8 MMS6
Cables used in CUE installations The CUE is the right choice of frequency converter in
Accessories
Note: When the CUE is installed in connection with SP installations as it meets all basic issues. The CUE
SP pumps, we distinguish between two types of has a pre-installed start-up guide which takes the
installation: installer through all the necessary settings.
• installation in EMC-insensitive sites. See fig. 14. The table below shows the issues to be considered
when using frequency converters in SP installations.
• installation in EMC-sensitive sites. See fig. 15.
The two types of installation are different when it
Issues to be considered Explanation
comes to the use of screened cable.
Note: Drop cables are always unscreened. The journal bearings must be
Ramp (up and down):
lubricated in order to limit wear
Maximum 3 seconds.
and overheating of windings.
CUE Filter Overheating of the motor => low
Use temperature monitoring by
insulation resistance => sensitive
Pt sensor.
to voltage peaks.
Reduce peak voltages Never exceed peak voltages of
Mains cable, Screened Drop cable, (max. 800 V peaks). 850 V at motor leads.
unscreened cable
cable unscreened For MS and MMS, we recommend
to use motors with 10 % extra in
Grundfos CUE with output filter is
given duty point.
a safe solution.
For MMS, always use motors
24
MMS6
8
MP 204 The MP 204 - many monitoring options
Accessories
The MP 204 monitors the following parameters:
The MP 204 is an electronic motor protector, designed
for the protection of an asynchronous motor or a pump. • insulation resistance before start-up
The motor protector consists of these parts: • temperature (Tempcon, Pt sensor and PTC/thermal
switch)
• a cabinet incorporating transformers and electronics
• overload/underload
• a control panel with operating buttons and display
for reading of data. • overvoltage/undervoltage
The MP 204 operates with two sets of limits: • phase sequence
• a set of warning limits • phase failure
• a set of trip limits. • power factor
If one or more of the warning limits are exceeded, the • power consumption
motor continues to run, but the warnings will appear in • harmonic distortion
the MP 204 display. • operating hours and number of starts.
Some values only have a warning limit.
The warning can also be read out by means of the
Grundfos R100 remote control.
If one of the trip limits is exceeded, the trip relay will
stop the motor. At the same time, the signal relay is
operating to indicate that the limit has been exceeded.
Applications
25
8 MMS6
The IO 112 has three inputs for measured values, one potentiometer for setting of
limits and indicator lights indicating the following:
• measured value of the input
• value of the limit set
96651601
• alarm source
• pump status.
Electrical data
• Supply voltage: 24 VAC - 10 %/+ 10 %, 50/60 Hz, or 24 VDC - 10 %/+ 10 %.
• Supply current: Min. 2.4 A, max. 8 A.
• Power consumption: Max. 5 W.
• Ambient temperature: -25 °C to +65 °C.
• Enclosure class: IP20.
Functions:
Digital input
• Float switch or pressure relay (if no IO 112 is used).
Analog input
• Too high motor temperature (Tempcon)
Consult WebCAPS on
• thermistor/PTC, pump
www.grundfos.com for
• pressure sensor, 4-20 mA (with IO 112).
product selection.
Relay output
• Pump alarm.
Communication
• Grundfos Remote Management.
• GSM/GPRS
(IO 112 not supported)
• Modbus RTU wired
(IO 112 not supported)
• Profibus DP
(IO 112 not supported).
Protection
• Protects the pump against short-circuit.
26
MMS6
8
G100 gateway for communication
Accessories
with Grundfos products
The G100 offers a wide selection of options for
integration of Grundfos products provided with
GENIbus interface into main control and monitoring
systems.
The G100 enables a pump installation to meet future
demands for optimum pump operation in terms of
reliability, operating costs, centralisation and
automation.
GR5940
Fig. 18 G100
Profibus-DP
Radio Direct
Modem PLC
SMS
Radio
Genibus DI Service
RS-232
4 digital inputs Service port for PC
Port 1 Port 2
Main
Network
Connection
Heating
GENIbus
Hydro
Multi-E MPC MGE E-pump MP 204 IO 351
MP 204 CU 300 DME E-pump IO 351
Pump Sensors
Pump SQE Sensors
27
8 MMS6
Product description
Accessories
FAULT RxD2
227 mm
Genibus DI Service
monitoring.
Port 1 Port 2
Network
Connection
28
MMS6
8
Cable termination kit, type KM
Accessories
Version
Product
Product Description Number of number
Motor cable [mm2] leads
For watertight shrink-joining of motor 1.5 - 6.0 3
Flat cable 116251
cable and submersible drop cable: 1.5 - 4.0 4
• cables of equal size. 6 - 10 4
• cables of different sizes. Flat cable 116252
10 - 16 3
• a cable lead and a single lead.
The joint is ready for use after a few 3
Flat cable 16 - 25 116255
minutes and requires no long 4
hardening time as do resin joints.
The joint cannot be separated.
29
8 MMS6
Cross-section of
leads Number of Product
connectors number
[mm2]
Accessories for cable kits M0 to 6-25 96626021
M6. 16-95 96626022
Screw connectors only. 4
35-185 96626023
GrA8251
70-240 96626028
Number of
Outer cable
leads and
diameter Weight Product
nominal
min./max. [kg/m] number
cross-section
[mm]
[mm2]
1 x 25 12.5 / 16.5 0.410 ID4072
1 x 35 14.0 / 18.5 0.560 ID4073
Suitable for these applications: 1 x 50 16.5 / 21.0 0.740 ID4074
• continuous application in groundwater and
potable water (approved for potable-water 1 x 70 18.5 / 23.5 1.000 ID4075
applications) 1 x 95 21.0 / 26.5 1.300 ID4076
• connection of electrical equipment, such as 1 x 120 23.5 / 28.5 1.650 ID4077
TM00 7882 2296
submersible motors
• installation depths up to 600 metres and 1 x 150 26.0 / 31.5 2.000 ID4078
average loads. 1 x 185 27.5 / 34.5 2.500 ID4079
Insulation and sheath of special EPR-based
3 x 25 26.5 / 34.0 1.450 ID4062
elastomer materials adapted to applications in
water. 4G1.5 10.5 / 13.5 0.190 ID4063
Maximum permissible water temperature: 70 °C. 4G2.5 12.5 / 15.5 0.280 ID4064
Maximum permissible lead service temperature:
90 °C. 4G4.0 14.5 / 18.0 0.390 ID4065
Further cable sizes are available on request. 4G6.0 16.5 / 22.0 0.520 ID4066
4G10 22.5 / 24.5 0.950 ID4067
4G16 26.5 / 28.5 1.400 ID4068
4G25 32.0 / 34.0 1.950 ID4069
4G35 33.0 / 42.5 2.700 96432949
4G50 38.0 / 48.5 3.600 96432950
4G70 43.0 / 54.5 4.900 96432951
30
MMS6
8
Zinc anodes Flow sleeves
Accessories
Application Grundfos offers a complete range of stainless-steel
flow sleeves for both vertical and horizontal operation.
Cathodic protection by means of zinc can be used for
We recommend flow sleeves for all applications in
corrosion protection of SP pumps in
which motor cooling is insufficient. The result is a
chloride-containing liquids, such as brackish water and
general extension of motor life.
seawater.
Flow sleeves are to be used in these cases:
Sacrificial anodes are placed on the outside of the
pump and motor as protection against corrosion. • If the submersible pump is exposed to high thermal
See fig. 21. load like current unbalance, dry running, overload,
high ambient temperature or bad cooling conditions.
• If aggressive liquids are pumped, since corrosion is
doubled for every 10 °C the temperature rises.
• If sedimentation or deposits occur around and/or on
the motor.
Note: More information about flow sleeves is available
on request.
31
8 MMS6
Product number
Cable length
Pt100 sensor with/without PR 5714 relay and cable PR 5714 MMS6
[m] MMS 10000
MS6 MMS 6000
MMS 12000
MMS 8000
20 Yes 96408953 96494596 96437287
40 Yes 96408681 96494597 96437288
60 Yes 96408954 96494598 96437289
80 Yes 96408955 96494599 96437290
100 Yes 96408956 96494610 96437291
20 No 96658626 96658629 96658633
40 No 96658627 96658630 96658634
60 No 96658628 96658631 96658635
GrA3187
Cable length
Pt100 sensor, including cable Product number
[m]
20 96913237
40 96913253
60 96913256
80 96913260
GrA3190
100 96913263
32
MMS6
8
Accessories
Extension kit for sensor cable for Pt100 Description Product number
33
8 MMS6
• 50 °C warning limit
The Pt1000 sensor offers these features:
Recommended setting: T-code +5 °C.
• continuous monitoring of the motor temperature
• 60 °C stop limit
• protection against too high motor temperature. Recommended setting: T-code +15 °C.
Protecting the motor against too high motor The Pt1000 sensor works within the temperature range
temperature is the simplest and cheapest way of of -60 °C to +120 °C.
ensuring long motor life. The Pt1000 ensures that the
operating conditions are not exceeded and indicates Technical data
when it is time to service the motor.
CU 220
Monitoring and protection by means of a Pt1000
Enclosure class IP65 (mounted in a control panel)
require the following parts:
Ambient temperature 0 °C to +55 °C
• Pt1000 sensor
Relative humidity 20-80 % (condensating)
• CU 220 control unit Voltage variation 1 x 230 V - 15 %/+ 10 %, 50 Hz
• cable Approvals UR
• staybolt kit for Pt1000. Marking CE
Product number
Cable
Pt1000 sensor with CU 220 control unit, cable and
length CU 220 MMS6
staybolt or insertion probe MMS 10000
[m] MS6 MMS 6000
MMS 12000
MMS 8000
20 Yes 96803207 96803233 96803238
TM04 3561 4508 - TM04 3563 4508
TM04 3562 4508 - TM04 3560 4508
Cable length
Pt1000 sensor, including cable Product number
[m]
20 96804042
40 96804044
TM04 3563 4508
60 96804064
80 96804065
100 96804067
34
MMS6
8
Accessories
Extension kit for sensor cable for Pt1000 Description Product number
35
9 MMS6
9. Cable sizing
Cable sizing
U U
L = -------------------------------------------------------------------------------------------------------- m
I 1.73 100 cos --- + sin X
q L
Legend
U = Rated voltage [V]
ΔU = Voltage drop [%]
I = Rated current of the motor [A]
q = Cross-section of submersible drop cable
[mm2]
XL = Inductive resistance: 0.078 x 10-3 [Ω/m]
cos φ = Power factor
sin φ = 1 – cos2
ρ = Specific resistance: 0.025 [Ωmm2/m]
36
MMS6
9
Cable sizing Example
Cable sizing
Motor size: 30 kW, MMS6
Calculation of cable cross-section
Rated current: I1/1 = 68.2 A
Legend Rated voltage: 3 x 400 V, 50 Hz
U = Rated voltage [V] Starting method: Direct-on-line
Required cable length: 200 m
ΔU = Voltage drop [%]
Water temperature: 25 °C
I = Rated current of the motor [A] cos φ: 0.81
q = Cross-section [mm2] Cable selection:
Choice A: 3 x 35 mm2
XL = Inductive resistance 0.078 x 10-3 [Ω/m] Choice B: 3 x 50 mm2
cos φ = Power factor Calculation of power loss
sin φ = 1– cos2 Choice A
L = Cable length [m] 2
LI
Δp = Power loss [W] p A = 3
---------------------------
q
r = 1/c
3 200 0.02 68.2 2-
Cable material p A = ----------------------------------------------------
35
Copper: c = 40 m/W x mm2
Aluminium: c = 35 m/W x mm2
p A = 1594 W
For calculation of the cross-section of the submersible
drop cable, use the following formulas: Choice B
Direct-on-line
3 200 0.02 68.2
2
p B = ------------------------------------------------------------
I 1.73 100 L cos 50
q = ------------------------------------------------------------------------------------------------
-
U U – I 1.73 100 L X sin
L ΔpB = 1116 W
Savings
68.2 1.73 100 200 1/52 0.81 Operating hours/year: h = 4000.
q = ------------------------------------------------------------------------------------------------------------------------
-
400 3 – 68.2 1.73 100 200 0.078 0.59 Annual saving (A):
q = 35 mm2
A = p – p h = 1594 W – 1116 W 4000 = 1912000 Wh
Star-delta A B
A = 1912 kWh
I 100 L cos By choosing the cable size 3 x 50 mm2 instead of
q = --------------------------------------------------------------------------------
U U – I 100 L X sin 3 x 35 mm2, an annual saving of 1912 kWh is
L
achieved.
The values of the rated current (I) and the power factor
(cos φ) can be found in the tables on pages 14 to 20. Operating time: 10 years
Saving after 10 years (A10):
Calculation of power loss
For calculation of the power loss in the submersible A = A 10 = 1912 10 = 19120 kWh
10
drop cable, use the following formula:
The saving must be calculated in the local currency.
2
3LI
p = ---------------------------
q
37
10 MMS6
Legend
- = Not in the standard program, i.e. FPV variant.
❍ = Not produceable.
● = We recommend to use of PE2/PA windings.
PE2/PA windings
Motor power
Ceramic/carbon SiC/SiC
13 17 - - - - - - - - - -
15 20 - - - - - - - - - -
18.5 25 - - - - - - - - - -
22 30 - - - - - - - - - -
26 35 - - - - - 96879531 - - - 96879533
30 40 - - - - - 96879532 - - - 96879534
37 50 ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍
3 x 220-230 V, 50 Hz
Product number
PVC windings
Motor power
Ceramic/carbon SiC/SiC
13 17 96881048 - 96881055 - - - - - ● ●
15 20 96881049 - 96881056 - - - - - ● ●
18.5 25 96881050 - 96881057 - - - - - ● ●
22 30 96879499 - 96879503 - - - - - ● ●
26 35 96879500 - 96879504 - - - - - ● ●
30 40 96879501 - 96879505 - - - - - ● ●
37 50 ❍ 96879502 ❍ 96879506 ❍ - ❍ - ● ●
38
MMS6
10
Order data
Product number
PE2/PA windings
Motor power
Ceramic/carbon SiC/SiC
PVC windings
Motor power
Ceramic/carbon SiC/SiC
Product number
PE2/PA windings
Motor power
Ceramic/carbon SiC/SiC
13 17 96880928 96880931 96880938 96880941 96880948 96880951 96880958 96880961 96880968 96880971
15 20 96880929 96880932 96880939 96880942 96880949 96880952 96880959 96880962 96880969 96880972
18.5 25 96880930 96880933 96880940 96880943 96880950 96880953 96880960 96880963 96880970 96880973
22 30 96879409 96879413 96879417 96879421 96879425 96879429 96879433 96879437 96879441 96879445
26 35 96879410 96879414 96879418 96879422 96879426 96879430 96879434 96879438 96879442 96879446
30 40 96879411 96879415 96879419 96879423 96879427 96879431 96879435 96879439 96879443 96879447
37 50 96879412 96879416 96879420 96879424 96879428 96879432 96879436 96879440 96879444 96879448
39
10 MMS6
Product number
PE2/PA windings
Motor power
Ceramic/carbon SiC/SiC
13 17 - - - - - - - - - -
15 20 - - - - - - - - - -
18.5 25 - - - - - - - - - -
22 30 - - - - - - - - - -
26 35 - - - - - - - - - -
30 40 - - - - 96879559 - 96879561 - 96879563 -
37 50 - - - - 96879560 - 96879562 - 96879564 -
PE2/PA windings
Motor power
Ceramic/carbon SiC/SiC
13 17 - - - - - - - - - -
15 20 - - - - - - - - - -
18.5 25 - - - - - - - - - -
22 30 - - - - - - - - - -
26 35 - - - - - 96879535 - - - 96879537
30 40 - - - - - 96879536 - - - 96879538
37 50 ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍
PE2/PA windings
Motor power
Ceramic/carbon SiC/SiC
13 17 - - - - - - - - - -
15 20 - - - - - - - - - -
18.5 25 - - - - - - - - - -
22 30 - - - - - - - - - -
26 35 - - - - - - - - - -
30 40 96879449 - 96879451 - 96879453 - 96879455 - 96879457 -
37 50 96879450 - 96879452 - 96879454 - 96879456 - 96879458 -
40
MMS6
10
3 x 460 V, 50 Hz
Order data
Product number
PVC windings
Motor power
Ceramic/carbon SiC/SiC
13 17 96881097 ❍ 96881103 ❍ - ❍ - ❍ ● ●
15 20 96881098 - 96881104 - - - - - ● ●
18.5 25 96881099 - 96881105 - - - - - ● ●
22 30 96879539 - 96879543 - - - - - ● ●
26 35 96879540 - 96879544 - - - - - ● ●
30 40 96879541 - 96879545 - - - - - ● ●
37 50 96879542 - 96879546 - - - - - ● ●
Product number
PE2/PA windings
Motor power
Ceramic/carbon SiC/SiC
PE2/PA windings
Motor power
Ceramic/carbon SiC/SiC
41
10 MMS6
Product number
PVC windings
Motor power
Ceramic/carbon SiC/SiC
Product number
PE2/PA windings
Motor power
Ceramic/carbon SiC/SiC
42
MMS6
10
3 x 380 V, 60 Hz, SF 1.15
Order data
Product number
PVC windings
Motor power
Ceramic/carbon SiC/SiC
13 17 96880978 - 96880985 - - - - - ● ●
15 20 96880979 - 96880986 - - - - - ● ●
18.5 25 96880980 - 96880987 - - - - - ● ●
22 30 96879459 - 96879463 - - - - - ● ●
26 35 96879460 - 96879464 - - - - - ● ●
30 40 96879461 - 96879465 - - - - - ● ●
37 50 96879462 - 96879466 - - - - - ● ●
Product number
PE2/PA windings
Motor power
Ceramic/carbon SiC/SiC
43
11 MMS6
WebCAPS
WebCAPS is a Web-based Computer Aided Product
Selection program available on www.grundfos.com.
WebCAPS contains detailed information on more than
220,000 Grundfos products in more than
30 languages.
Information in WebCAPS is divided into six sections:
• Catalogue
• Literature
• Service
• Sizing
• Replacement
• CAD drawings.
Catalogue
Literature
Service
44
MMS6
11
Replacement
CAD drawings
2-dimensional drawings:
• .dxf, wireframe drawings
• .dwg, wireframe drawings.
3-dimensional drawings:
• .dwg, wireframe drawings (without surfaces)
• .stp, solid drawings (with surfaces)
• .eprt, E-drawings.
WinCAPS
WinCAPS is a Windows-based Computer Aided
Product Selection program containing detailed
information on more than 220,000 Grundfos products
in more than 30 languages.
The program contains the same features and functions
as WebCAPS, but is an ideal solution if no internet
connection is available.
WinCAPS is available on CD-ROM and updated once
a year.
Subject to alterations.
45
46
47
Being responsible is our foundation
Thinking ahead makes it possible
Innovation is the essence
97824689 1111
GB
Repl. 97824689 1210
The name Grundfos, the Grundfos logo, and the payoff Be–Think–Innovate are registrated trademarks
ECM: 1084616 owned by Grundfos Management A/S or Grundfos A/S, Denmark. All rights reserved worldwide.