ASME 8313-2020
Table 323.2.2 Requirements for Low Temperature Toughness Tests for Metals (20)
These Toughness Test Requirements Are in Addition to Tests Required by the Material Specification
‘column B
Design Minimum
Column A Temperature Colder Than
Design Minimum Temperatureator WarmerThan Minimum | Minimum Temperature ia
"Temperature in Table Ac, Table AM,
Table Ae, Table AM, or Figure 323.2.28 oras Described in | or Figure 323.2.2A or as
“Type of Material Para, 323:22(H) Described in Para, 323.2.2(h)
Tied [Gray iron ‘Acd No additional requirements Bel No additional requirements
Materials [2 yallesble and ductile [A-2 No additional requirements B-2 Materals designated is
tron, carbon steel in Hox 2 shal not be used
ccorgance with
Note
(@) Base Meal ( Wald Metal (Note
3 Other carbon stels; Tow /A-3 (a) No additional A-3 (B) The weld metal ofthe | B-¥ Each heat est unto Tot of|
Oi interme aug” | Sauder ‘welding procedure qualification |" base material as Wentiied in
Steel and ferrtic test coupon shall be impact. | che appliable base metal
martensitic, and duplex tested at or below the design | _ specification shall be inpact
Sailessstels Tninimam temperature wen | tested except when Note G)
that temperature is less than | or Note (4) is sated. When
STase (i), except when ‘materials are subjected to
Note (3) or Note (a) issatisfied,| heat treatment during fare
Trspact esting ofthe weld metal | cation, including hot bending
isnot required when the las: | or forming and postweld heat
Siicaton ofthe welding {reatment such as that
ansumables accordingto the | requived by Table 83114,
ler metal specification impact testing shall be
Feguires impact testing at or | performed om material that
below the design minitaum | has been subjected ta heat
temperature ‘eatment simolaing the
aniiipated heat treatment,
including, for postweld heat
‘eaten at east 0% ofthe
Une at temperature. Each
‘welding procedute speci
ton shall be quatiied i
fecordance with Table
Sas
“hasten stainless steels | AA Ca) 4 (b] Weld metal deposits shal 4 Base metal and weld metal
Glcarbon content by "he smpact tested in accordance | deposis shall be impact
‘analysis 90.198 oF swith para, 325.3 I design tested in accordance with
(2) materials notin minimum temperature para. 323.3-SeeNoes (2), (5),
solemn reated | S250 (207 exept ae and (6).
ondition then impact provided in para, 3242.2 and in
testin accordance mith {| Rotes (3) and (6),
para. 325.3 for design
‘ninimum tempera
SEs" C20 except
4 provided in
Notes (3) and (6)
‘Austenitic ductile iron |A-S (a) No additional [AVS (B) Welding isnot permitted, | BS Base metal shall be impact
‘ASTM ASTI requirements tested in accordance wi
ara s284,Do not use
ESib6-c(-920-F), Weldingis
ot permitted.
Aluminum, copper, |A-G (a) No adional | A6 (B) No addtional Bs Designer shall be assured
nikal, and ser alloys; | requirements, ‘oqulrements unless filer by suitable tests [see
‘nalloyed stanium Imetal composition is outside | Nowe (7) that bate metal
the range for pase metal Weld deposits, and HAZ are
‘ompostion then test in Sultable atthe design
Sevordance with item 5-6 ‘zimurs temperature
Unlisted | 7 An unlisted material shall conform ta published specification. Where composition, heat treatment, and product form are
‘Materias| ' comparable to those ofa listed materia, requirements for the corresponding listed material shall be met Other unlisted
materials shall be qualified as coqulred in the applicable section of column B
NOTES:
(0) Carbon ste conforming tothe following ae subject tothe limitations in Hox B-2:platesin accordance with ASTM A36, A283,and AS70;pipe
snaccordance with ASTM A134 when made from these plates structural shapesin accordance with ASTM A992; and pipe im accordance with
ASTM AS3 Type F and APLSI. Gr, A25,
‘ust wel,
(2) Impact ests that meet the requirements of Table 3233.1, which are performed a part ofthe weld procedure qualification, wil satisfy ll
requirements of pars, 323.22, and need not be repeated for production welds,
(3) See paras. 3282.2) through (0.
49