- HITACHI
FOR MESSRS : DATE: May.28,2007
CUSTOMER'S ACCEPTANCE SPECIFICATIONS
LMG7420PLFC-X
CONTENTS
No. ITEM SHEET No. PAGE
1_|COVER 7B64PS 2701-LMG7420PLFC-X-6 |1-1/4
2__|RECORD OF REVISION 7B64PS 2702-LMG7420PLFC-X-6 |2-1/2~2/2
3_|GENERAL SPECIFICATION 7BG4PS_2703-LMG7420PLFC-X-6 [3-1/1
4 [ABSOLUTE MAXIMUM RATINGS __|7B64PS 2704- LMG7420PLFC-X-6 4-1/1
5 |ELECTRICAL CHARACTERISTICS | 7B64PS _2705-LMG7420PLFC-X-6 |5-1/1
6 [OPTICAL CHARACTERISTICS 7B64PS_2706-LMG7420PLFC-X-6 |6-1/2~2/2
7__|BLOCK DIAGRAM 7B64PS_2707- LMG7420PLFC-X-6 |7-1/1
8 _|INTERFACE TIMING 7B64PS_2708- LMG7420PLFC-X-6 |8-1/2~2/2
9 JOUTLINE DIMENSIONS 7B63PS 2709-LMG7420PLFC-X-6 |9-1/3
7B64PS_2709- LMG7420PLFC-X-6 |9-2/3~3/3.
10 _JAPPEARANCE STANDARD 7B64PS_2710- LMG7420PLFC-X-6 |10-1/5~5/5
41_|PRECAUTION IN DESIGN 7B64PS_2711-LMG7420PLFC-X-6 |11-1/2~2/2
12_|DESIGNATION OF LOT MARK 7B64PS_2712-LMG7420PLFC-X-6 |12-1/1
13. |PRECAUTION FOR USE 7BG4PS_2713-LMG7420PLFC-X-6 |13-1/1
ACCEPTED BY:
* When product will be discontinued , customer will be informed by HITACHI with
twelve months prior to discontinuation.
KAOHSIUNG HITACHI Sh.
ELECTRONICS CO.,LTD. | No.
7B64PS 2701-LMG7420PLFC-X-6RECORD OF REVISION
DATE SHEET No. SUMMARY
Feb.10,'95. |7B64PS 2704- |CHANGED : _
|LMG7420PLFC-X-2 OPERATING
PAGE 4-1/1 ae MIN | MAX
AMBIENT TEMPERATURE | 0c | 40°C
+
OPERATING
ITEM MIN | MAX
LAMBIENT TEMPERATURE, 0c | 50°C _|
7B64PS 2705- [CHANGED
|LMG7420PLFC-X-2 CONDITION __TYP.
PAGE 5-1/2 VDD-V0 | Ta=40C.6=100 15.4
+
CONDITION TYP.
VOD-V0_ | Ta=50°C f= 100 152
IMAR.30,'99 |7B64PS 2709- ICHANGED :
ILMG7420PLFC-X-3 |CABLE’S LENGTH & LOCATION
IPAGE 9-1/3
)JUL.07,'99 |7B64PS 2706- (6.2 OPTICAL CHARACTERISTICS OF BACKLIGHT.
ILMG7420PLFC-X-4 | BRIGHTNESS (TYP.) CHANGED
PAGE 6-2/2 40 -» 90 (TYPING ERROR REV.3)
- RISE TIME (TYP.) CHANGED
20 — 5 (TYPING ERROR REV.3)
7B64PS 2707- (7. BLOCK DIAGRAM
|LMG7420PLFC-X-4 ALL PAGE CHANGED (TYPING ERROR REV.3)
PAGE 7-1/1
Feb.14,'05 |7B64PS 2703- |Added :
LMG7420PLFC-X-5 | (10) CFLLIFETIME 50Khrs
PAGE 3-1/1
\7B64PS 2705- 5.2 ELECTRICAL CHARACTERISTICS OF
ILMG7420PLFC-X-5 |BACKLIGHT
PAGE 5-1 THE NOTE. 4.5 ADDED
7B64Ps 2706- [Changed -
lLMc7420PLFc-x-5 | 6.2 OPTICAL CHARACTERISTICS OF BACKLIGHT.
IPAGE 6-2/2 BRIGHTNESS
MIN. 70.0 — 100.0
TYP. 90.0 — 150.0
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD.
Sh.
DATE] May.28,'07 |, | 7B64Ps 2702-LMG7420PLFC-x-6 |PAGE| 2-1/2,RECORD _OF REVISION
DATE SHEET No. SUMMARY,
May.28,07 |7B64PS 2709- —_|9.3 Internal Pin Connection
LMG7420PLFC-X-6 |Changed :
PAGE 9-3/3 CFL I/F: Mitsumi M63M83-04 > JAE IL-G-4S-S3C2-SA
\7B64PS 2712- 12. DESIGNATION OF LOT MARK
LMG7420PLFC-X-6 |Added
PAGE 12-1/1 REV No. ITEM, LOT No.
CFL VF Connector
Mitsumi_M63M83 - 04
| CFL I/F Connector :
A
JAI }S-S3C2-SA mozt
KAOHSIUNG HITACHI Sh.
ELECTRONICS CO.,LTD. |DATE| May.28,'07 No, | 7B84PS 2702- LMG7420PLFC-X-6 PAGE | 2-2/2,3. GENERAL SPECIFICATIONS
(1) Part Name
2
(3)
(4
()
(6)
7
Module Size
Dot Size
Dot Pitch
Number Of Dots
Duty
LCD Type
@
Q
(10)
Viewing Direction
Backlight
CFL Lifetime
LMG7420PLFC-X
159.4(W)mm x 101.0(H)mm x11.0(Oynm max
0.47(W)mm x 0.47(H)mm
0.50(W)mm x 0.50(H)mm
240(W) x 128(H)dots
11128
Film type black / white (Negative type)
The upper polarizer is anti-glare type.
(Hardness.3H)
The bottom polarizer is transmissive type.
6 O'clock
Cold cathode fluorescent lamp
50k hrs.
KAOHSIUNG HITACHI
ELECTRONICS Co.,LTD.|DATE|
May.28,'07
“| 7B64PS 2703- LMG7420PLFC-X-6
PAGE| 3-4/4,4. ABSOLUTE MAXIMUM RATINGS
4.1 Electrical Absolute Maximum Ratings. VSS = OV : Standard
ITEM — SYMBOL | MIN MAX. _[UNIT[ COMMENT.
|Power Supply For Logic VvbD-vss |__0 65 Vv
Power Supply For LC Drive VDD-VEE | __0 20.5 Vv.
Input Voltage Vi 0.3 _[ voD+0.3 |_V
Input Current ti 0 4 A
[Static Electricity = = = =| (Note 4)
Note 1: Make certains you are grounded when handling LCM.
4.2 Environmental Absolute Maximum Ratings
OPERATING STORAGE
uae MIN. MAX. MIN. MAX. eee
[Ambient Temperature oc 50°C -20°C 60°C __|(Note 2,3)
Humidity (Note 1) (Note 1) |Without Condensation
4.9mIs? 19.6m/s°
lVibration 7 e (2G) |(Note 4)
cee) (Note 5)
|Shock
29.4m/s* |490.0m/s*
: ae) - _[Meoe) PO Dresions
[Corrosive Gas Not Acceptable Not Acceptable
Note 1
Note 2
Note 3
Note 4
Note 5
Tas40T : 85%RH max
Ta>40 : Absolute humidity must be lower than the humidity of 85%RH at 40°C
Ta at -20°C —< 48h, at 60°° —< 168h.
Background color changes slightly depending on ambient temperature.
This phenomenon is reversible
Higher starting voltage of CFL and higher LCD driving voltage are needed
while operating at 0°C.
The life time of CFL will be reduced while operating at 0°C. Need to make sure
the value of IL and characteristics of inverter.
Also the response time at 0°C will be slower.
5Hz~100Hz (Except Resonance Frequency)
This module should be operated normally after finishing the test.
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD.
May.28,'07
Sh.
No.
pare
BS4PS 2704-LMG7420PLFC-X-6 ace| 4-14,5. ELECTRICAL CHARACTERISTICS
5.1 ELECTRICAL CHARACTERISTICS
ITEM — ‘SYMBOL [CONDITION [| MIN. | TYP. | MAX. [ UNIT
Power Supply Voltage VDD-VSS - |
For Logic 475 | 50 | 525 | Vv
ILC driver Circuit Power VEE-VSS -15.5 |-15.0] -145 | V
lSupply Voltage
Input Voltage vi H LeveL [osvod| - | vod | Vv
L_LEVEL 0 = _|o2von| Vv
Power Supply Current IDD a
For Logic (Note 1) vop-vss=5.0v]} - | 11.7} 14.0 | ma
Power Supply Current IEE | VDD-vss=5.0v| - | 25 | 40 | mA
For LCD (Note 1)
Recommended - [tea] - Vv
LC Driving Voltage (Note 2)| VDD-Vo = [168] - Vv
= [1s2y = Vv
Note 1: VDD-V0=15.8V , Ta=25°C
Note 2: Recommended LC driving voltage may fluctuate about
Test pattern is all “Q’.
5.2 ELECTRICAL CHARACTERISTICS OF BACKLIGHT
41.0V by each module.
ITEM SYMBOL] MIN. | TYP. | MAX. | UNIT | NOTE
Lamp Voltage VL 360 | - | vims | Ta=26c
Frequency fl 30 70 a5 | kHz | Ta=25
Lamp Current w | 25 | 6 | 55 [mams| Ta-25%
Starting vs : :
Discharge Voltage (Note 2) | 190 | Virns .}. Tar25c
Please certainly inform HITACHI before designing lamp drive circuit according to the
above specifications.
Note 1: Please make sure that your inverter is designed to meet the above
specifications
Note 2: Starting discharge voltage is increased when LCM is operating at lower
temperature.
Please check the characteristics of your inverter before applying to your set.
Note 3 : Average life time of CFL will be decreased when LCM is operating at lower
temperature.
Note 4: Under lower driving frequency of an inverter, a certain backlight system (CFL
& CFL reflection sheet) may generate a sound noise.
Note 5: When IL Is used over 5.5mA, it may cause uneven contrast near CFL location.
due to heat dispersion from CFL.
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD.
Sh.
DATE| May.28,07 |
\7B64PS 2705- LMG7420PLFC-X-6
lo,
PAGE| 5-1/46. OPTICAL CHARACTERISTICS
Viewing Direction
Note 2: Definition of viewing angle
6.1_ OPTICAL CHARACTERISTICS Ta
ITEM ‘SYMBOL CONDITIONAL [ MIN. | TYP.
\Viewing Area $2-¢1 30_| 40
Contrast Ratio K - | 20
Response Time (Rise) tr =| (160)
Response Time (Fall) tf =| (110)
(Measure condition by HITACHI)
Note 1: Definition of 0 and ¢ Note 3 : Definition of contrast ‘k”
ke —Brightness on selected dot (81)
(Normal) ~ “Brightness on non-selected dot (B2)
y(O=180+)
Bt
SW x 3 o=10°
C a (82)
y(9=0) 2
a
8.
1 and 62.
kp 61<10| 2 ss 2
: m1} |ee ye
E é& JE
be
° oO
Bases a
ewlksgle 8-8 88e8 e ge.
KAOHSIUNG HITACHI Sh.
ELECTRONICS CO.,LTD. IDATE| May.28,'07, No. 7B64PS 2707-LMG7420PLFC-X-6 |PAGE| 7-1/1,8. INTERFACE TIMING
8.1 INTERFACE TIMING
ITEM SYMBOL MIN._[ TYP. [ MAX. | UNIT ]
IC7D Setup Time ‘CDS 100 | - - [ns
IC/D Hold Time tCDH 10 = = [ns
CE, RD, WR Pulse CE. tRD, WR | 80 = =| "ns
Data Setup Time 1DS 80 = =| — ns:
Data Hold Time tDH 40 = =| ns)
[Access Time tacc | =_| 150 | “ns
(Output Hold Time {OH 10 =| 50 [ns
c/D
DO~D7
(WRITE)
DO ~D7
(READ)
KAOHSIUNG HITACHI
ELECTRONICS Co.,LTD.|PATE|
May.28,'07
Sh.
7B64PS 2708- LMG7420PLFC-X-6
PAGE
8-4128.2 TIMING OF POWER SUPPLY AND INTERFACE SIGNAL
4.75V
VDD GND VDD
SIGNAL. GND SIGNAL
VEE GND VEE
Power on Power off
The missing pixels may occur when the LCM is driven beyond above power
interface timing sequence.
8.3 POWER SUPPLY FOR LCM (EXAMPLE)
VDD
vss
LCM
vo
VEE
Recommend
VR:10~20kQ
VDD-VO : LCD driving voltage
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. 7B64PS 2708- LMG7420PLFC-x-6 |PAGE
Sh.
[oxre| May.28,'07 fe9. OUTLINE DIMENSIONS
9.1 OUTLINE DIMENSIONS
1) +10 max. (Note 1)
159.4 -
35 __ 152.440.3 =
85 142.4
10 139.4
69 124.040.3
0.5 max. 123.0min. 3 3 gla}
(2.015) | 0.5x239+0.47=119.9740.1 Sle Rone fee
3 6 S
a
g 10 TT i
3 CNS | {i Bezel Opening
8 (Note 2) = t! Effective Viewing Area q
a) I i! g|
ea ° i Active Area x
—r! Ih al |
~ —— 1020 Bl <] 2] jo)
° 56] S| 18! el
2.5440.3 |e sia] es] "3/8
5 8
2 Nt TS XL |
g ° 3
a yy 2
sg :
3 4 7 |
s 2 Pelle
ol 4
: c|
ay Q or —
soe) 5 50:5
30- $1.0 ema & =
vt]
CN2
Unit : mm.
Scale : NTS
Viewing Direction
Tolerance not specified is +0.5mm a
Note 1: Mesurement when adding 9.8x10° Pa
(1.0kgf/cm? ) At the measuring point
Note 2 : Do not connect any signal to CN3.
Use CN1 as interface
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. ae
May.28,07
Fi 7B63PS 2709-LMG7420PLFC-X-6
PAGE
9-1/3,9.2 DISPLAY PATTERN
119.97 (240 Dots)
4
wo &
oo
z
2 1
4 ' }
8
g i i
= i
é
&
8) ' 1
'
! 1
: 1
\ 1
. 1
' 1
' 1
LL 047
ae SS
5 {05
Scale: NTS
Unit: mm
Measurement Tolerance : #0.1
KAOHSIUNG HITACHI | | are! May.28,°07 |" 'S 2709- LMG7420PLFC-x-6 |PAGE| 9-2/3
ELECTRONICS CO.,LTD. 12.28/07 | io, | “BOAPS 2709: LMG7420P 6 a9.3 INTERNAL PIN CONNECTION
cNt es
PIN No. | SYMBOL FUNCTION
Al VSS(0V) _|Ground
AZ VDD(+5V)_|Power supply for logic circuit |
A3 VO [Power supply for LCD drive
|WR="L" : C/D="H" Command write
Ad ciD "L" Data write
Status read
C/D="L" Data read
AS WR |Data write (Data write at “L”)
‘AG RD [Data read (Read data at “L”)
AT~14 DBO~DB7_[Data bus
At5 CE_ Chip enable (CE must be “L”)
A16 RET [Reset
At7, VEE(-15V) [Power supply for LCD drive
Ais “D.OFF -- |NC/Display , GND/Display off
A19 F/S |Character font select : F/S="H" 6°8Font
F/S="L’_8*8Font
720 [PIN [Display mode reverse.
CN2 Se
INTERRFACE | PIN No. | SYMBOL] LEVEL FUNCTION
CFL CFL i ‘GND 5
HE 2 N.C : 0 cont -
| 3 N.C 5 INo_connection
Ll HV - Power supply for CFL
| 4
CFL WF : JAE IL-G-4S-S3C2-SA
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD.
Sh.
DATE] May.28,'07 |. | 7864PS 2709. LMG7420PLFC-x-6
PAGE | 9-3/3,10. APPEARANCE STANDARD
10.1 APPEARANCE INSPECTION CONDITION
Visual inspection should be done under the following condition.
(1) In the dark room
(2) With CFL panel lighted with prescribed inverter circuit.
(3) With eyes 25cm distance from LCM.
(4) Viewing angle within 45 degrees from the vertical line to the center of LCD.
& &
eye eye
Bezel
10.2 DEFINITION OF EACH ZONE
A zone : Within the effective display area specified at page 9-1/3 of this document.
B zone: Area between the window of bezel line and the effective display area line
specified at page 9-1/3 of this document.
KAOHSIUNG HITACHI ing | Sh.
ELECTRONICS CO..LTD [DATE] Mav:28.07 |, |7864PS 2710-LwGraz0PLFC-x6 [PAGE| 10-1/540.3 APPEARANCE SPECIFICATION
(1) LCD appearance
*) If the problem occurs about this item, the responsible person of both party
(customer and HITACHI) will discuss more detail
No. ITEM CRITERIA _
‘Scratches Distinguished One Is Not Acceptable =Te]
(To be judged by HITACHI standard)
it ‘Same as above le
[Wrinkles In Polarizer [Same as above “|e
[Bubbles Average Diameter D(mm) | Maximum Number Acceptable _|
D=0.2 Ignored |
0.2