Safety Data Sheet
Page: 1/9
Japan Chemical Industies Safety:
Preparation / Revision Date : 29 October 2010
Product: TOYOTA Injector Cleaner especialy for D-4 series petroleum engin
1. IDENTIFICATION
Trade name
Manufacturer
Company Name
Address
Telephone Number
Facsimile Number
Person In Charge
‘deta sheet according
TOYOTA Injector Cleaner
JOL-MSDS-603141
(Pin:08813-00830
especially for D-4 series petroleum engine
Japan Chemical Industries co.,Lté
813, Kikkawa, Shimizu-ku, Shizuoka, 424-8568 Japan
+81(64)345-3476
+81(64)347-6865
8,Ogura(Prepared by M.Matsunaga)
Emergency Telephone Number: +81 (64)345-3476
2. HAZARDS IDENTIFICATION
GHS classification
PHYSICAL HAZARDS
Explosives
Flammable gases
Flammable aerosols
‘Oxidizing gases
Gases under pressure
Flammable liquids
Flammable solids
Self-reactive substances and mixtures
Pyrophoric liquids
Pyrophoric solids
Self-heating substances and mixturés
‘Substance and mixtures which, in contact
with water, emits flammable liquids
Oxidizing iquids
Oxidizing solids
Organic peroxides
Corrosive to metals
HEALTH HAZARDS
Acute toxicity (Oral)
Acute toxicity (Dermal)
Acute toxicity (Inhalation: gas)
‘Acute toxicity (Inhalation: Vapor)
Acute toxicity (Inhalation: Dust)
Acute toxicity (Inhalation: Mist)
Skin corrosioniiritation
Serious eye damage/eye irritation
Respiratory
Skin sensitization
Germ call mutagenicity
Not appiicable
Not applicable
Not applicable
Not applicable
Not applicable
Category 4
Not applicable
Classification not possible
Not classified
Not applicable
Classification not possible
Classification not possible
Classification not possible
Not applicable
Not applicable
Classification not possible
Not classified
Category 6
Not applicable
Classification not possible
Not applicable
Classification not possible
Category 2
Category 2A
Classification not possible
Catagory 4
Classification not possibleSafety Data Sheet Page: 2/9
‘Japan Chemical Industies Safety deta sheet according JQLMSDS-50314
Preparation / Revision Date : 29 October 2010
Product, TOYOTA Injector Gleaner especially for D4 series potroloum ongine P/N:08813-00630
Carcinogenicity Category 2
Reproductive toxity Classification not possible
Specific target organ toxlity-Single exposure Category 1.2.3,
Specific target organ tovicty-Repeated exposure Category 1,2
Aspiration hazard Category 1
ENVIRONMENTAL HAZARDS
Hazardous to the aquatic environ ment—Acute hazard Category 2
Hazardous to the aquatic environment—Chronic hazard Category 2
Pictogram
Signal word Danger
Hazard statement
Combustible liquid
May be harmful in contact with skin
Causes skin irritation
Causes serious eye irritation
May cause an allergic skin reaction
‘Suspected of causing cancer
‘Causes damage to organs
May cause damage to organs
May cause respiratory iritation; or May cause drowsiness and dizziness.
‘Cause damage to organs through prolonged or repeated exposure
May cause damage fo organs through prolonged or repeated exposure
Toxic to aquatic ite
Toxic to aquatic ife with long lasting effects
Precautionary statement
[A safety measure]
Wear protective gloves and eye/fece protection.
Keep away from flames and hot surfaces.
‘Wash hands thoroughly after handling,
Avoid breathing mist vapours.
Contaminated work olothing should not be alowed out of the workplace.
Obtain special instructions before use.
Do not handie until all safety precautions have been read and understood.
Use personal protective equipment as required.
Do not eat, dtink or smoke when using this product.
Do not breathe mistvapours.
Use only outdoors or in well-ventilated area.
Avoid release to the environment.
[First-aid measures}Safety Data Sheet Page: 3/9
Japan Chemical Industies Safety deta sheet according JOLMSDS-60314
Preparation / Revision Date : 29 October 2010
Product TOYOTA Injector Gleaner especially for D4 series petroleum engine PIN:08819-00630,
In the case of fire, use carbon dioxide / powder extinguishant / sprinkling /
‘alochol-tesistant-related fire foam for fie extinguishing, The stick flooding adds to danger.
Call a POISON CENTERidoctor/physician if you feel unwell.
IF ON SKIN: Wash with plenty of soap end water.
‘Take of contaminated clothing and wash before re-use,
If skin iritation or rash ocoure, seek medical advice/attention,
IF IN EYES: Rinse cautiously with water more than 15 minutes. Remove contact lenses, if
present and easy to do. Continue rinsing,
if eye irritation persists, get medical advice/attention
Wash contaminated clothing before reuse.
IF exposed or concerned: Get medical attention/advioe.
IF exposed: Call a POISON CENTER or doctor/physician,
Call a POISON CENTER or doctoriphysician if exposed or you feel unwell
IF INHALED: Remove to fresh ait and keep at rest in a position comfortable for breathing.
Get medical attention/advice if you feel unwell
IF SWALLOWED: Immediately call a POISON CENTER or doctoriphysician.
Do NOT induce vomiting,
Collect spillage.
[Handling and storage]
‘Store locked up,
Store conlainer tightly closed in coolwell-ventilated place.
Keep out of reach of children,
[Disposal considerations}
Inthe case of the disposal, please confirm local disposal regulation concerned by all means.
3. COMPOSITION / INFORMATION ON INGREDIENTS
Chemical nature Polyether amine in solvent naphtha
‘Composition ingredients
Component wis, CASNo,__ EINECS No
Poyether amine 70.0~80.0 Confideniial +
‘Solvent naphtha, heavy aroma, 20.0~30.0 @4742-94-5 265-1985
Hazardous Components
Chemical name Wi% __CAS No,_EINECS No__Hazard symbol _ R-phase
Payether amine 70.0~80.0 Confident * N R563
Sdlvent naphtha 20.0~90.0 G4742-045 265-198-5 XN R5AN53,R65 REGRET
4,24-Timethyl benzene 0.8~1.3 95-63-6 —202-436-9-XnN RIOR2ORIEII7IOB,
4,3,5-Tiimethyl benzene <1 108-67-8 203-6044 XN RIORI7RSA53
Naphthalene 18~2.7 91-20-38 202-048-5 nN R22RAO.RSOISS
* :Polyether amine is in compliance with the EC Seventh amendment Directive 92/32/EEC,
The wording of the hazard symbols and R-phrases Is specified in chapter 16 if dangerous
Ingredients are mentioned.
4, FIRST AID MEASURES
General advice:Safety Data Sheet Page: 4/9
Japan Chemical Industies Safety data sheet according JQI-MSDS-6031-4
Preparation / Revision Date : 28 October 2010
Product TOYOTA Injector Cleaner ospecially for D-4 sories potroleum engine P/N:08813-00830
Immediately remove contaminated clothing.
If inhaled:
If dificulties occur after vapor has been inhaled, remove to fresh air and seek medical
attention,
‘Skin contact:
‘Wash thoroughly with soap and water. Get medical attention if irritation develops.
Contact with eyes:
Wash affected eyes for at least 15 minutes under running water with eyelids held open.
IFinitation persists, get medical attention.
On ingestion:
DO NOT INDUCE VOMITING. If conscious,
attention,
ive 2 glasses of water. Get immediate medical
Note to physiciant
Treatment: Treat according to symptoms (decontamination, vital functions), no known specific
antidote.
6. FIRE-FIGHTING MEASURES
Flash point: 66 degrees Celsius
Suitable extinguishing media:
CO,, dry chemical, or foam.
Water can be used to cool and protect exposed material,
Unsuitable extinguishing med
water jet for safety reasons
Firefighting Procedures:
Wear full protective fire-fighting gear including self-conlaining breathing apparatus operated In the
positive pressure mode with full-ace coat, pants, gloves and boots, Water may cause spiattering
Unusual Fire & Explosion Hazards:
Toxic fumes, gases of vapors may evolve on buring
6, ACCIDENTAL RELEASE MEASURES
Personal precautions:
Personal protective equipment must be wor, see Personal Protection Section for Personal
protective equipment recommendations.
\Ventilate area if spilled in confined space or other poorly ventilated areas.
Environmental precautions:
Contain contaminated water
waters/groundwater.
Methods for clearing up or taking up:
For large amounts: Pump off product.Safety Data Sheet Page: 5/9
Jopan Chemical Industies Safety data sheet according JOL-MSDS-6034-4
Preparation Revision Date : 29 October 2010
Product: TOYOTA Injector Cleaner especialy for D4
ries petroleum engine PIN:08813-00830
For residues: Pick up with suitable absorbent material. Dispose of absorbed material in
accordance with regulations.
HANDLING AND STORAGE
Handling if
No special measures necessary provided product is used correctly
DO NOT handle, store or open near an open flame, sources of heat or sources of ignition.
‘Take precautionary measures against static discharges.
Keep containers closed when not in use.
Do not discharge into drains or the environment, dispose to an authorized waste collection point.
Use appropriate containment to avold environmental contamination.
Wash thoroughly after handling.
Storage
Further Information on storage conditions:
Store ina cool piace.
Protect from direct sunlight
8, EXPOSURE CONTROLS/PERSONAL PROTECTION
3
Other Exposure
See Hazardous Ingredients Section for any applicable exposure mits for components.
Ventilation Procedures:
Use local exhaust ventilation to control mists or vapors.
Additional ventilation or exhaust may be required to maintain air concentrations below
recommended exposure limits.
Personal Protective equipment
Hand protection:
Chemical resistant protective gloves (EN 374)
Suitable materials also with prolonged, direct contact (Recommended: Protective index 6,
corresponding > 480 minutes of permeation time according to EN 374):
fluoroelastomer (FKM) - 0.7 mm coating thickness
Polyethylene-Laminate (PE laminate) - ca, 0.1 mm coating thickness
Suitable materials short-term contact and/or splashes (recommended: At least protective index 2,
corresponding > 20 minutes of permeation time according to EN 374)
nitrile rubber (NBR) - 0.4 mm coating thickness
Manufacturer's directions for use should be observed because of great diversity of types.
Eye Protection:
Safely glasses with side-shields (frame goggles) (EN 166)
Respiratory Protection:
Respiratory protection in case of vapor/aerosol release.
Body protection:
Body protection must be chosen depending on activity and possible exposure, 9. apron,
protecting boots, chemical-protection suit (according to DIN-EN 485).Safety Data Sheet Page: 6/9
Japan Chemical Industries Safety data sheot according JOLMSOS-5031-1
Preparetion / Revision Date : 29 October 2010
Product TOYOTA Injector Gleaner especially for 0-4 serlas petroleum engine PIN:08613-00630
General safety and hygiene measur
Hardie in accordance with good industrial hygiene and safety practice, Wearing of closed work
clothing is required additionally to the stated personal protection equipment,
9. PHYSICAL AND CHEMICAL PROPERTIES
Form liquid
Color yellowish-brown
Odor ‘ammonia
pH Not determined.
Botting point 2180 degrees Celsius (at Solvent naphtha)
Melting point Not determined.
Flash point 66 degroes Celsius
‘Autoignition temperature > 400 degrees Celsius (at Solvent naphtha)
Explosive limit in air between 0.6 and 7 vol% (at Solvent naphtha)
Vapor pressure Not determined,
Density 0,042 glam? (16 degrees Celsius)
Solubilty in water insoluble
Viscosity approx. 63 x 10 m’/s (25 degrees Celsius)
10, STABILITY AND REACTIVITY
Stability
Material is normally stable at moderately elevated temperatures and pressures.
Decomposition Temperature:
Not determined,
Incompatib
Strong acids. Strong oxidizing agents
Polymerization:
Will not occur
‘Thermal Decomposition:
‘Smoke, carbon monoxide, carbon dioxide, aldehydes and other products of incomplete
‘combustion. Ammonia may be formed on burning in limited air supply. Propylamine,
polyalkylglycols, and aliphatic alcohols may also be released.
11, TOXICOLOGICAL INFORMATION
Acute Exposure
Oral Toxélty:
‘The LDS0 in rats is >6000 mg/kg at Polyether amine). Based on data from components or similar
materials,
‘Swallowing this material causes severe initation of the mouth, esophagus and stomach.
Eye Iritation:
May cause eye irritation, but will not injure eye tissue.
Skin Irfitation:
Not expected to bs a primary skin iritant. Based on actual data.Safety Data Sheet Page: 7/0
‘Japan Chemical Industios Safoty data sheat according JOLMSDS-6034-4
Prepavation | Revision Data : 29 October 2010
Product TOYOTA Injector Cleaner especially for D- series petroleum engine PIN:
13-0830
Dermal Toxicity:
The LDso In rabbits Is > 2000 mg/Kg (at Polyether amine). Based on data from components or
similar materials,
Inhalation Toxicity
No data available to indicate product or components may be a tonic inhalation hazard.
Respiratory Iritation:
May cause nose, throat and lung iritation. Based on data from similar materials.
12, ECOLOGICAL INFORMATION
Environm 4
Freshwater Fish Toxicity:
‘The acute LC5O Is 1 - 10 mg/L. based on actual data (at Polyether amino).
Freshwater:
Not determined.
Invertebrates Toxicity Algal Inhibition:
The acute E050 is 10 - 100 mg/l. based on actual data(at Polyether amine).
Saltwater Fish Toxécity:
Not determined.
Saltwater Invertebrates Toxicity:
Not determined,
Bacteria Toxicity:
Not determined,
Miscellaneous Toxicity:
Not determined.
Biodegradation:
This product shows limited biodegradation based on QEOD 301-type test data for similar
products
Bioaccumulation:
This material displays no potential to bloconcentrate.
Soil Mobility:
Not determined,
43. DISPOSAL CONSIDERATIONS
Must be dumped or incinerated in accordance with local regulations.
Contaminated packaging:
Uncontaminated packs can be re-used.Safety Data Sheet Page: 8/9
Japan Chemical Industries Sofety data sheot according JOLMSDS-6031-4
Preparation / Revision Date : 29 October 2010
Product, TOYOTA Injector Cleaner especially for D4
ries potroloum engine PIN:08813-00830
Packs that cannot be cleaned should be disposed of in the same manner as the contents,
14. TRANSPORT INFORMATION
Land and inland navigation transport (ADRIRID)
UN No. 3082
Transport document name ENVIRONMENTALLY HAZARDOUS SUBSTANCE LIQUID.N.O.S
Class 9
Packing Group m
Marine transport (IMDG)
UN-No. 3082
Proper shipping name ENVIRONMENTALLY HAZARDOUS SUBSTANCE LIQUID.N.OS .
Class 9
Packing Group 1
Marine Pollutant applicable
Air transport (ICAOJIATA)
Proper shipping name ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID.NO.S.
UN No, 3082
Class 8
Packing Group 0
48. REGULATORY INFORMATION
Regulations of the European union (Labeling) / National legislation / Regutations
Directive 1999/45/EEC (Preparation Directive’):
Hazard symbol(s)
Xn Harmful
N Dangerous for the environment
Rephrase(s)
R37 Iritating to respiratory system.
R653 Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic
environment.
R65 Harmfut may cause lung damage if swallowed.
ROS Harmfut may cause lung damage If swallowed.
R87 Vapors may cause drowsiness and dizziness,
S:phrase(s)
$23 Do not breathe gas/fumes/vaporispray.
824 ‘Avoid contact with skin.
‘836/37 Wear suitable protective clothing and gloves.
Bt ‘Avoid release to the environment. Refer to special instructions/Safely data
sheets.
S62 IF swallowed, do not induce vomiting ; seek medical advice immediately and show
this container or label
Global Chemical Inventories
EU ‘All components on EINECS.
USA All components on TSCA Inventory or exemptSafety Data Sheet Page: 9/9
Jepan Chemical Industies Safely data sheet according JOL-MSDS-6034-1
Preparation / Revision Date : 29 October 2010
Product: TOYOTA Injector Cleat ally for D-4 series petroleum engine PIN:08613-00830
Canada All components on DSL.
Japan All components METI.
Australia All components on NICNAS.
Korea All components on ECL.
Philippines All components on PICS.
China All components IECSC.
16. OTHER INFORMATION
Full text of hazard symbols and R-phrases if mentioned as hazardous components
in chapter 2:
Rephrase(s)
Rio Flammeble
R20 Harmful by inhalation,
R22 Harmful if swallowed.
R96/37/38 Irritating to eyes, respiratory system and skin,
Rao Limited evidence of a carcinogenic effect.
RAS May cause cancer.
R46 May cause heritable genetic damage.
REO/53 Very toxic to aquatic organisms, may cause long-term adverse effects in the
aquatic environment.
‘The information contained herein is based on the present state of our knowledge and does not
therefore guarantee certain properties. Recipients of our product must take responsibilty for
observing existing laws and regulations.