os
r\S
AK ANN
Q3
- KIET Group of institutions
‘PUE Examination (2021-2022) EVEN Sem
Year: 2021-22
Subject Name: Engineering Mechanics
Duration: 3 Hrs
te: Attempt all the questions of each section
a _____Section-A
7 | Attemptall parts. :
| and explain law of forces
on’s theorem.
truss? How it-differ from an Impereat wuse?
pl of Pure Bending
down the statement of parallel axis theorem with figura
State the difference between Centrold and Canter of Gravity
[State D'Alember's principle.
‘What do you understand by relalive veloally?
[ Define shear stress and its complimentary shear aiess,
the concept of simple bending =
Sections
| Find the unknown force F, in the system of forces as shown in figure 1,
E1= 100N, Fe = 1S0N and the resultant ofthese three forces (F, Fa and |
| Fa)is 200 N.
Q2
Fig. 4
Course: B.Tech,
Semester: IV
Subject Code: KmE-402
Max. Marks: 100,
MeO)
| CO leu Kel
OR
friction.
Find out forces in all members of the truss.
sev —»8
J2KN
CO -Course Outeome generally refer to traits, Knovledge, skill set that a student attains after completing the course successfully,
ing of assessment of student’ learning.
Bloom’s Level (BL) - Bloom's taxonomy framework is planning and desi
A body weighing 300 N is resting on a rough horizontal table. A pull of
100 N is applied at an angle of 15° with the horizontal to just cause the:
body to slide over the table, Find normal reaction and the coefficient of
*Kaowledge Categories (KCs): F-Factual, C-Conceptual, P-Procedural, M-Metacognitive
Reference to Competitive Exams (GATE, GPAT, CAT, GRE, TOFEL, NET, etc. )
\
|| State and prove the parallelaxis theorem. ETS |
Ta toe aeppod ic e wel shear to siko Te walar in 4$6CoNeS FB KL 5-4)
the depth of the well, assuming the velocity of sound to be 335 m/sec. ™,
as ‘OR
Derive the relationship between the linear motion of geometric centre and |
‘angular motion of wheel rolling without slipping |
7A bar of 20 mm diameter is tested in tension. itis Observed that when a |"
| load of 37.7 KN is applied, the extension measured over a gauge lengtir)” -
‘of 200 mim is 0.12 mm and contraction in diameter in 0.0036 mm. Make |
calculation for Poisson's ratio and elastic constants, E, G, K. |
as Sano: =
[Calculate the maximum stress in a propeiler shafi 40 om external and 20
| cm intemal diameter, when subjected to twisting moment of 4650 Nm. If
| the modulus of rigidity G = 82 Gpa, given that length is 29 times external |» Z = >
| ciameter. ace
= SEeSection-CHes
Eee : i Sa,
]An equilateral triangular plate of sides 200 mm is acted upon by four| Gate | | \
forces as shown in figure-2, Determine the magnitude and direction of the | 2008 | |
| | resultant of this system of forces and its position from A. \
| | $0 kN |
| a7 3 | apic
|
30 kN
{ GO-Course Outcome generally refer to traits, knowledge, sil st that student utang afer complating the course sucesfally.
{Bloom's Level (BL) - Bloom's taxonomy frameworks planing and designing of assessment of students leasing
2 wledge Categories (KCs); F-Factual, C-Conceptual,P-Proéedural, MeMetacognitive
‘Reterence to Competitive Exams (GATE, GPAT, CAT, GRE, TOFEL, NET, etc. )=A
Fora ladder of lengin 4m, =
Ee eR orca oe ca YW
slipping. =0.2 between the wall and ladder, and w 0 3 fo t
indder he ladder weigh 200 W and man weigh 600 Nis a3 m fi Be
A, (Point A is on floor) is Nee
Find out forces in BC, CF and FE truss by method of section. | tow
\ i \s
as s
| “FIC
OR 2
Draw SED and BMD of below given beam
sou
ronnie
€ \
| \
ee en in | \
Determine the moment of inertia of the section shown in figure about the | \
horizontal centroidal axis. Also find the moment of inertia of the section \
about the symmetrical axis. Hence find the polar moment of inertia,
Soph crcte
Tent D106 whet
y= 14553\0 Wet
S 4
Typ 76864256 opuit
|
a9 f |
OR 2 soil |
Galeutate the moment of inerfia of the composite a7c8 Shown infig. about
the centroidal axis.
y
a
40mm |
\
| |
, tae nl
=
cn snote knowledge, skill set that 2 student atains after completing the
rant af ctudent’s lear vibe~ ae Vaya
ee ee wa
ae
Koll 0.
[ @.10 | The equation of motion of a particle moving na straight line is given by:
| S=18t+3t%2¢
| | where S is the total distance covered fre
| | the end of t seconds.
| Calculate:
|
| ( velocity and acceleration at the start | Be con
ee the time when the particle reaches its maximum velocity
| |
GR |
{Two bodies A and B are connected by a thread and move along a rough
| | horizontal plane ( =0.3) under the action of a force 400 N applied to the |
| body 8 as shown in figure 4. Determine the acceleration of the two bodies
| | and the tension in the thread, using D'Alembert’s principle.
| 00 N =
| Oh ea ae aa
{ O oe | \
| 200N rs 400 ee |
begs |
| a : | |
L { | i
Q.11 | A circular pipe of external diameter 70 mm and thickness 8 mm is used | |
| 8s a simply supported beam over an effective span 2.5m. Find the
| maximum concentrated load that can be applied at the center of the span
q if permissible stress in tube is 150N/mm?.
= OR
Write down the assumptions used in puré Torsion and derive the Torsion
| Equation. i
) the starting point in meters at
ond |
|
521963 ENT .