Professional Documents
Culture Documents
SAIC-M-2003 Rev. 7 Receiving Insp of Structural Steel
SAIC-M-2003 Rev. 7 Receiving Insp of Structural Steel
EQUIPMENT ID NUMBER(S) EQUIPMENT DESCRIPTION EQPT CODE SYSTEM ID. PLANT NO.
LAYOUT DRAWING NUMBER REV. NO. PURCHASE ORDER NUMBER EC / PMCC / MCC NO.
SCHEDULED INSPECTION DATE & TIME ACTUAL INSPECTION DATE & TIME QUANTITY INSP. MH's SPENT TRAVEL TIME
SAUDI ARAMCO USE ONLY
SAUDI ARAMCO TIP NUMBER SAUDI ARAMCO ACTIVITY NUMBER WORK PERMIT REQUIRED?
ITEM
ACCEPTANCE CRITERIA REFERENCE PASS FAIL N/A RE-INSP DATE
No.
12-SAMSS-007,
A6 Minimum thickness of any part of structural shape shall be 5 mm.
Para. 4.1.2
Structural steel shapes have deviations not exceeding the tolerances 12-SAMSS-007,
A7
noted in Attachment 1 of this checklist. Para. 7.9
Pipe for columns or handrail shall be per ASTM A53 Type E or S, 12-SAMSS-007,
A8
Grade B, ASTM A106 Grade B or API SPEC 5L, Grade B. Para. 4.3
Page 1 of 3
SAUDI ARAMCO ID/PID - 18-MAY-05 - REV 0 (Standards Cutoff - )
SAIC NUMBER DATE APPROVED QR NUMBER
SAUDI ARAMCO INSPECTION CHECKLIST
Receiving Inspection of Structural Steel Shapes & Plates SAIC-M-2003 20-Feb-14 Structural
PROJECT TITLE WBS / BI / JO NUMBER CONTRACTOR / SUBCONTRACTOR
ITEM
ACCEPTANCE CRITERIA REFERENCE PASS FAIL N/A RE-INSP DATE
No.
All bolts, washers and nuts shall be packaged in rigid, weatherproof 12-SAMSS-007,
A9
containers. (Note: Cardboard containers are not acceptable.) Para. 6.3.1.2
All gusset and stiffener plates shall be 3/8 inch (10 mm) minimum
thickness. For minor structures such as platforms and miscellaneous
12-SAMSS-007,
A10 structures, ¼ inch (6 mm) thick gusset and stiffener plates may be
Para. 6.2.8.4
used. (Exception: Connection plates in electrical transmission towers
or communication towers shall be 6 mm.)
Where contact of dissimilar metals will cause galvanic corrosion, a 12-SAMSS-007,
A11
suitable insulating material shall be provided between the metals. Para. 4.1.3
12-SAMSS-007,
A12 Structural tubing shall be per ASTM A501 or ASTM A500 Grade B.
Para. 4.4
Floor and Roof metal deck shall be cold-formed steel sheets
12-SAMSS-007,
A13 conforming to ASTM A446 or ASTM A611 or equal having a minimum
Para. 4.5
yield strength of 228 N/mm² (33,000 psi).
The metal deck shall be galvanized and receive a protective coating of 12-SAMSS-007,
A14
zinc conforming to ASTM A635/A635M, G90 Coating Designation. Para. 4.5
Crane Rails shall be as follows:
12-SAMSS-007,
A15 a. Rails 60 to 84 lb./yd. – ASTM A1
Para. 4.12
b. Rails 104 to 175 lb./yd. - ASTM A759
Checkered Floor Plates shall be ASTM A786 / ASTM A786M Pattern 2 12-SAMSS-007,
A16
or 4 and ASTM A36 / ASTM A36M. Para. 4.13
Welded Steel Bar Grating shall be as follows:
a. per ASTM A1011/11011M
12-SAMSS-007,
A17 b. galvanized per ASTM A123 and NAAMM MBG 531.
Para. 4.14
c. Top surface of bearing bars shall be plain, unless serrated is
specified.
B. Handling, Storage and Preservation
Materials shall be kept free of dirt, grease, and other foreign 12-SAMSS-008,
B1
matter.(PIP-STS01530, Para. 6.1.1) Sec. IV, 6.5.8
REMARKS:
REFERENCE DOCUMENTS:
2- 12-SAMSS-007 -- Fabrication of Structural and Miscellaneous Steel, 17 May 2011
3- 12-SAMSS-008 -- Erection of Structural and Miscellaneous Steel, 9 May 2011
3. Schedule Q
Page 2 of 3
SAUDI ARAMCO ID/PID - 18-MAY-05 - REV 0 (Standards Cutoff - August 2004)
SAIC NUMBER DATE APPROVED QR NUMBER
SAUDI ARAMCO INSPECTION CHECKLIST
Receiving Inspection of Structural Steel Shapes & Plates SAIC-M-2003 18-May-05 MECH-
NOTE: Allowed variation as per ASTM A6/A6M are as follows:
A. Allowed T = T' variations in Cross Section for W, HP, S, M, C, and MC Shapes, per ASTM A6/A6MTABLE 16
B. Allowed Variations (T) in End Out-Of-Square for S, M, C, MC, L, T, Z, and Bulb Angle per ASTM A6/A6M, TABLE 20
Page 3 of 3