Professional Documents
Culture Documents
View All Callouts: Function Isolation Tools
View All Callouts: Function Isolation Tools
GET
Adobe Acrobat Reader
SAVE
a copy of this schematic
THE BOOKMARKS PANEL WILL ALLOW YOU TO THE FUNCTION ISOLATION TOOLS ISOLATE
QUICKLY NAVIGATE TO POINTS OF INTEREST. CIRCUITS FOR TRACING HYDRAULIC LINES
Grids On/Off
Machine Views
FUNCTION KEYS
Zoom In “CTRL” / “+”
Zoom Out “CTRL” / “-”
Fit to Page “CTRL” / “0” (zero)
Hand Tool “SPACEBAR” (hold down)
Find “CTRL” / “F”
WHEN ONLY ONE CALLOUT IS SHOWING ON A Search “CTRL” / “SHIFT” / “F”
CHECK
Control
ACCUMULATORS Unidirectional Bidirectional
Valves
Line Restriction
(Variable)
VARIABLE DISPLACEMENT
Basic Spring Shuttle NON- COMPENSATED
Pilot
Symbol Loaded Line Restriction
Controlled Spring Loaded Gas Charged Restriction
(Fixed)
Unidirectional Bidirectional
2-Section
RELEASED PRESSURE Variable and Pressure
ROTATING SHAFTS Compensated
Pump
Internal
Simplified Complete Supply Pressure Hydraulic Pneumatic
Energy Triangles
COMBINATION CONTROLS
LINES MEASUREMENT
Solenoid Solenoid Solenoid Solenoid and Servo Thermal Detent Crossing Joining
or Manual and Pilot Pilot or Manual Pressure Temperature Flow
Push-pull Lever Manual Shutoff General Manual Push Button Pedal Spring Vented Pressurized Return Above Fluid Level Return Below Fluid Level
PUBLICATIONS.CAT.COM
© 2022 Caterpillar. All Rights Reserved. CAT, CATERPILLAR, LET’S DO THE WORK, their respective logos, “Caterpillar Corporate Yellow”, the “Power Edge”
and Cat “Modern Hex” trade dress as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.
COMPONENT LOCATION
Schematic Machine
Description
Location Location
Filter As B-5 1
Gauge - Pressure 1 D-4 2
Gauge - Pressure 2 D-4 3
Receptacle - Liquid Natural Gas E-7 4
Receptacle - Vent E-5 5
Regulator Gp B-4 6
Strainer - Liquid Natural Gas E-7 7
Tank - LNG Fuel E-6 8
Valve - Chassis Relief A-5 9
Valve - Check 1 (Not Shown) C-3 10
Valve - Defuel Relief C-4 11
Valve - Defuel Shut Off B-4 12
Valve - Engine Vent A-3 13
Valve - Excess Flow C-7 14
Valve - Fill Line Check C-7 15
Valve - Fill Line Shut Off D-7 16
Valve - Line Relief D-7 17
Valve - Primary Relief D-7 18
Valve - Secondary Relief C-7 19
Valve - System Vent A-6 20
Valve - Tank Isolation B-7 21
Valve - Vent Shut Off E-5 22
Valve As - Thermal Relief A-5 23
Valve Gp - Fuel A-3 24
Valve Gp - Gas Actuation A-4 25
Vaporizer As - Liquid Natural Gas A-6 26
7 6 5 4 3 2 1
(12) VALVE -
DEFUEL
(Dimensions: 34 inches x 24 inches)
B (1) FILTER AS B
VENT STACK LNG OUT
M0136575
465-3352
LINE PATTERNS
PRD
Pressure Line
(24) VALVE GP - FUEL
Pilot / Load Sensing Pressure
(26) VAPORIZER AS - LNG 596-1051
Drain / Return Lines
554-3064
Air Line
(25) VALVE GP - (13) VALVE - ENGINE VENT HYDRAULIC CIRCUIT COLOR DESCRIPTIONS
Component Group
16 Page,
459-0623
THIS SCHEMATIC IS FOR THE 785 DYNAMIC GAS BLEND (DGB) WITHOUT
(9) VALVE - CHASSIS RELIEF (23) VALVE AS - THE ECONOMIZER CONVERSION SYSTEM
579-5197 THERMAL RELIEF Do not operate or work on this product unless you have MEDIA NUMBER: M0136575
read and understood the instruction and warnings in the
553-0293 relevant Operation and Maintenance Manuals and SCHEMATIC PART NUMBER: 457-6003, CHANGE: 04, VERSION: -
relevant service literature. Failure to follow the instruc- Components are shown installed on a fully operable machine with the key and engine off, transmission shifter
tions or heed the warnings could result in injury or
in neutral and with parking brake set.
death. Proper care is your responsibility.
Refer to the appropriate Service Manual for Troubleshooting, Specifications and Systems Operations.
Refer to the Parts Manual using a specific serial number prefix in SIS before ordering parts from this schematic.
7 6 5 4 3 2 1
ENGINE FRONT
VIEW ALL CALLOUTS
24
25
13
6
LIQUID NATURAL GAS TANK
VIEW ALL CALLOUTS
16
19
15
14
20 2 22 5 7 4
21
23
17
12
3
18
11
26 1