bizhub C364e/¢2640/62240
J REWRITING OF FIRMWARE,
+ There are two ways to updat the firmware: One is by directly connecting with the main body using the USB memory device, and the
other is by downloading over a network using the Intemet ISW.
NOTE.
* The settings in the “Utility” mode and the "Service Mode" will not be changed, when the firmware is updated,
‘+ Rewrite BootROM and install the loadable device driver, OCR dictionary, and PDFIA fonts as necessary depending on the
firmware to be rewritten and the user's usage pattern,
FTbizhub C364e/¢2640/02240 4J_REWRITING OF FIRMWARE > 1. Contfrming the fimware version
1. Confirming the firmware version
4.4 Procedure
1. Call the Service Mode tothe screen,
2. Select the [Firmware Version}.
3. Check ifthe fimware version is updated,
NOTE
* After conducting firmware updating, check the firmware version No. and confirm that the firmware has been normall
updated
TZbizhub C364e/¢2640/62240 J REWRITING OF FIRMWARE > 2. USB memory
2, USB memory
Note
~ USB memory must be connected with the maln power switch off
+ When updating the firmware, use the service por.
Ieannot be updated when connected to other USB port
21 Preparation
Conditions for USB memory which ean be used for updating the fmware areas fllows
* USB flash memory compatible with the USB (1.1/2.0) interface
+ Formatted tothe FATS2 fle system
+ Memary capacity of 2GB or less recommended."t
+ Not including security features (Possible to tu OFF security features)
+ AUB flash memary that appears as mullplecrives on a comuler cannot be used
NoTE
+ "4: Possible to be non-operational products.
22 Procedure
1, Extract the obtained femware data
2. Connec! the USB oe PC, ard copy he extracted frware data tothe oot directory of he USB memory
f fore
Cre cae)
fe Est ier Terr
Gomer seme tm aT
= 80000) ~ (ap) aetna
* Seo Lene eto
et te came Soaks
ae Gosie Samer ister
5 ont a eee ee
a Seer Gee Geen
Umee dee nines
rears Mah La
ein eet .
NOTE
* More than one firmware data with
ingle model can be stored in the USB memory.
In this case, copy the firmware data to the USB memory according to the following procedures.
1. Copy the firmware data to the root directory of the USB memory.
(When making a folder and storing more than one firmware data, its also necessary to copy the firmware data to the root
directly.)
2, Make the folder named “FWSelect” (case-sensitive) tothe root directory of the USB memory
'3, Make a folder with any folder name (one byte alphameric characters, maximum 40 characters) under
and store the firmware data to the folder.
-WSelect”
Go:
le fot er eck
<= BEET gp
c Ben
dew ae a
a Girvsaea) tet
1 ret Gineaie canmat
san (J few anne
ee
ht moet stMH6LseF ihe
motu | :
~
Turn OFF the main power switch
Remove the screw [1].
Litup the cover [2 ofthe service por.
Insort tho USB memory device [3] tothe service port
Tsbizhub C364e/¢2640/62240 J REWRITING OF FIRMWARE > 2. USB memory
(31
1]
< ies
q i id
\ )
(2)
Nore
* USB memory must be connected with the main power switch off
+ When updating the firmware, use the service port.
Ieannot be updated when connected to other USB port.
7. Turn ON the main power switch.
Control panel shows FIW items tobe updated, and sect the particular typeof FW to he updated. (Select [YES].)
5
5
3
rier ru
Q
FAX SOARD [Mtn Fee Sie]
[Pre
2496 SOOTHE TEU ASTD
5
FIW to be updated ‘Ropropriate board Remark
MEP CONTROLLER [SSD beard (SSB)
‘SCANNER MFP board (FPS)
PRINTER Printer contol board (PROB)
FAX BOARD CONTROLLERT Fax board (FAXBIT) [Ony when FST is mounted
FAX BOARD CONTROLLER? Fax board2 (FAXBI2) [Only when FICS11 is mounted
[ADE (OF-¥) IDF conivol board (OF CB) [Only when DE-TONDF-24 is mounted
FINSHER FS control board (FSCB) [Only when FSSISIFS-544 is mounted
RU FS controlboara (FCB) [Only when FSB33IFS-534 is mounted
SD. [SD ative board (SDDB) [Only when SD-511 is mounted
DSCT [DSC boardit (OSCANI) [Only when SC-508 is mounted
DSGZ [DSC board? (OSC) [Only when SC-508 1s mounted
NOTE
* Unless one ofthe keys on the control pane! is pressed, firmware is automatically updated after 30 seconds when the main
ower switch is turned on.
+ When the BootRom fils isin the firmware data, [BootRom] key is displayed. Prossing the key updates data.
+ When more than one firmware are stored in step 1, pressing [FW Data Select] enables selection. (Data of other models cannot
be selected)
(Data with” atthe lft top of data selection screen willbe the default data copled to the root directly n the USB memory.)
+ By pressing [Machine Type Select}, you can set machine information. For details, refer to "J.2.4 Entering the machine type
information”.
8. Press the [START]. (Atthis tme, the Start key starts blinking red)
10. Check thatthe conral panel shows the message indicating thal the data has been rewritten corecly([Downloading Completed). Check
als the check sum value ((Creck Sum #) shown on the control panel. (The Start key lights Blue.)
11, Turn OFF the main power switch.
v4blzhub C364e/¢2640/62240 J REWRITING OF FIRMWARE > 2. USB memory
12, Remove the USB memory device, and fix the cover of the service port using a screw.
13, Tum ON the main power swith,
14, Call the Service Mode to the screen.
15, Select [Firmware Version}
18, Make sure i he version of firmware is updated
2.3 Action when data transfer fails
+ IF'NG* appoars on the control panel indicating that rewriting has been unsuccessful (in which case the Start key ght up red), take the
folowing stops.
1, Perform the data ewting pracedure again,
2. Ifthe procedure is abnormally terminated, change the USB memory for a new ane and try another rewriting sequence.
2. Ifthe procedure is stl abnormally terminated, change the board that has caused "NG" and carry out dala rewrling procedure,
FIW tobe updated ‘Appropriate board Remark
MEP CONTROLLER 350 board (SSDB)
SCANNER, MEP board (MFPB)
PRINTE! Printer control board (PROB)
FAX SOARO CONTROLLERT Fax boardit (FAXBI) Only when FST is mounted
FAX BOARD CONTROLLERZ Fax boardl2 (FAXBI2) Only whan FACSI1 is mounted
[ADF (OF) DF control board (OFCB) Only whan DF-TOT/DF-624 is round
FINISHER, FS control board (FSCB) Only when FS-533/FS.534 is mounted
RU. FS control board (FSCB) Only when FS-533/F5-534 is mounted
8D, 5D drive board (S008) Only when SD-511 is mounted
DECI DSC boarait (OSCBM Only when S508 s mounted
DSGz DSC boardi2 (OSCR) Only when SC508 s mounted
2.4. Entering the machine type information
+ Whon MEP board is replaced, itis necessary lo enter the machine lype information.
+ Refer to the following procedures to entar the machine type information.
Procedure
1. Inset the USB memory to the service por,
2. Tum ON the main power swt.
3. Touch Machine Type Select
Firmware Uniate Phe do rot turn ofthe ran Sa
[Reine
[Presence
2496 SOOTHE TEU ASTD
4. Enter [Machine] and [Type] information accoring tothe folowing table, Then touch [Fix
TSbizhub C364e/¢2640/62240 J REWRITING OF FIRMWARE > 2. USB memory
Tiscrine Type Select io |
=| Ge
EJEIE
Ciel
- f] e|fo F es °
[Machine] [1 1
5. Touch [OK, and tum OFF the main power switch
I