Professional Documents
Culture Documents
md0000001807201702 LC 258036
md0000001807201702 LC 258036
RT530E-2
36
80
ISO / DIN STABILITY
25
258036
SERIAL NUMBER
ON OUTRIGGERS 0% EXTENDED
25
TIRE INFLATION.................................................................................................. 18
10. For safe operation, the user shall make due allowances for his particular job conditions, such as: soft or uneven ground, out of level
conditions, high winds, side loads, pendulum action, jerking or sudden stopping of loads, experience of personnel, two machine
(tandem) lifts, traveling with loads, electric wires, obstacles, hazardous conditions, etc. Side pull on boom or jib is extremely dangerous.
11. If machine is equipped with individually controlled powered boom sections, the boom sections must be extended equally at all times.
12. Never handle personnel with this machine unless the requirements of the applicable national, state, and local regulations and safety
codes are met.
13. Keep load handling devices a minimum of 107 cm below boom head at all times.
14. The boom angle before loading should be greater than the loaded boom angle to account for deflection.
15. Capacities appearing above the bold line are based on structural strength and tipping should not be relied upon as a capacity limitation.
16. Capacities for the 8.8 m boom length shall be lifted with boom fully retracted. If boom is not fully retracted, capacities shall not exceed
those shown for the 12.2 m boom length.
17. When operating the machine in the "On Outriggers 50% Extended (4.3 m spread)" mode, the outrigger beam pins must be engaged.
When operating in the "On Outriggers 0% Extended (2.4 m spread)" mode, the outrigger beams must be fully retracted. Failure to follow
these precautions could result in structural damage or loss of stability of the machine.
18. Regardless of counterweight and outrigger spread configuration, no deduct is required from the main boom charts for a stowed boom
extension.
19. Do not lift loads when boom is fully lowered. The Load Moment Indicator (LMI) senses pressure and will not provide warnings or lockout.
The crane can become overloaded if lift cylinder(s) is fully retracted.
20. The maximum outrigger pad load is 24,857 kg.
DEFINITIONS:
1. Operating Radius: Horizontal distance from a projection of the axis of rotation to the supporting surface before loading to the center
of the vertical hoist line or tackle with load applied.
2. Loaded Boom Angle (Shown in Parenthesis on Main Boom Capacity Chart): is the angle between the boom base section and the
horizontal, after lifting the rated load at the rated radius with the rated boom length.
3. Working Area: Areas measured in a circular arc about the center line of rotation as shown on the working area diagram.
4. Freely Suspended Load: Load hanging free with no direct external force applied except by the lift cable.
5. Side Load: Horizontal force applied to the lifted load either on the ground or in the air.
HOIST PERFORMANCE
Wire Hoist Line Drum Rope
Rope Pulls Capacity (m)
Layer Available kg* Layer Total
1 5,280 23 23
2 4,754 26 49
3 4,323 29 78
4 3,960 31 109
5 3,656 34 143
6 3,397 36 179
*Max. lifting capacity: 6x37 class = 5,280 kg
35x7 class = 5,280 kg
9
10,300 10,500 10,375
(39.5) (52.5)
8,750
(30.5)
(60)
8,955
(47.5)
369,055
(56.5)
7,825
(65)
7,270
(62)
6,890
(69)
6,400
(66)
6,165
(72)
5,760
(69.5)
5,900
(73)
5,485
(71)
7,530 7,710 7,660 6,810 5,985 5,330 5,125
10
(17) (42) (52.5) (59) (63.5) (67.5) (69)
80
5,515 5,505 5,520 5,265 4,715 4,485
12
(27.5) (43.5) (52) (58) (62.5) (64.5)
4,110 4,120 4,140 3,685 3,495
14
(32.5) (44.5) (52) (57.5) (60)
See 3,135 3,155 3,175 3,200 3,150
16
Note 16 (15) (36) (45.5) (52.5) (55)
25
9
*3,265 2. 7.9 m and 13.7 m boom extension lengths
(76) may be used for single line lifting service.
3,060 *2,380
10
(75) (76) 3. Radii listed are for a fully extended boom with
2,710 *2,425 2,300 the boom extension erected. For main boom
12
(71.5) (76) (75.5) lengths less than fully extended, the rated
14
2,375 2,185 2,040 loads are determined by boom angle. Use
(68) (73) (72.5) only the column which corresponds to the
2,105 1,990 1,860 *1,235 boom extension length and offset for which
16
(64.5) (69.5) (69.5) (76)
the machine is configured. For boom angles
1,890 1,825 1,675 1,235
18
(61) (65.5) (66.5) (75)
not shown, use the rating of the next lower
1,705 1,655 1,520 1,230
boom angle.
20
(57) (62) (63.5) (71.5) WARNING: Operation of this machine with
22
24
1,540
(53.5)
1,180
(49)
1,530
(58)
1,365
(53.5)
1,370
(60.5)
1,270
(57)
36
1,155
(68.5)
1,120
(65)
heavier loads than the capacities listed is
strictly prohibited. Machine tipping with boom
extension occurs rapidly and without ad-
885 1,040 1,165 1,060
vance warning.
26
(44.5) (48.5) (54) (61.5)
80
4. Boom angle is the angle above or below
635 765 970 995 horizontal of the longitudinal axis of the boom
28
(39.5) (43.5) (50) (57.5)
base section after lifting rated load.
530 755 935
30
(37.5) (46.5) (53.5) 5. Capacities listed are with outriggers fully
565 760 extended and vertical jacks set only.
25
32
(42) (49)
565
34
(43.5)
0.1A (kg) 260 245 230 210
Min. boom angle
for indicated length 24° 30° 30° 30°
(no load)
Max. boom length
at 0° boom angle 24.4 m 24.4 m
(no load)
NOTE: ( ) Boom angles are in degrees. A6-829-100581B
#LMI operating code. Refer to LMI manual for instructions.
*This capacity based on maximum boom angle.
**7.9 m capacities are also applicable to fixed offsettable ext. However,
the LMI codes will change to #0051 and #0053 for 0° and 30° offset,
respectively.
Radius #9005
in Main Boom Length in Meters
Meters
8.8 12.2 15.2 18.3
11,550 10,575 *7,460
3
(61) (70) (76)
9,445 8,825 7,460
3.5
(57) (67.5) (72.5)
7,875 7,450 7,010
4
(53) (64.5) (70.5)
6,470 6,370 6,065 5,705
4.5
(48.5) (62) (68.5) (72.5)
5,335 5,350 5,270 5,000
5
(43.5) (59) (66) (71)
3,660 3,675 3,685 3,695
6
(31.5) (53.5) (62) (67.5)
8
36
2,650
(47)
1,980
2,660
(57.5)
1,990
2,665
(64)
2,000
(39.5) (52.5) (60)
1,495 1,505 1,515
80
9
(30.5) (47.5) (56.5)
1,125 1,135 1,145
10
(17) (42) (52.5)
610 615
12
25
(27.5) (43.5)
0.1A (kg) 300 280 265 255
Minimum boom angle (°) for indicated
length (no load)
32
Maximum boom length (m) at 0° boom
angle (no load)
15.2
NOTE: ( ) Boom angles are in degrees.
#LMI operating code. Refer to LMI manual for
operating instructions.
*This capacity is based on maximum boom angle.
Lifting Capacities at 0° Boom Angle
On Rubber Stationary - 360°
Boom Main Boom Length in Meters
Angle 8.8 12.2 15.2
2,545 1,025 350
0 deg.
(6.9) (10.3) (13.4)
NOTE: ( ) Reference radii in meters.
A6-829-100565C
8
4,945
(47)
3,920
(39.5)
4,955
(57.5)
3,930
(52.5)
4,965
(64)
3,935
(60)
365. On rubber lifting with boom extensions not permit-
ted.
6. For pick and carry operation, boom must be cen-
tered over front of machine, mechanical swing lock
3,170 3,180 3,185 engaged and load restrained from swinging. When
9
80
(30.5) (47.5) (56.5) handling loads in the structural range with capaci-
2,600 2,610 2,615 ties close to maximum ratings, travel should be
10
(17) (42) (52.5) reduced to creep speeds.
1,795 1,800
12 7. Axle lockouts must be functioning when lifting on
(27.5) (43.5)
rubber.
25
1,250
14 8. All lifting depends on proper tire inflation, capacity
(32.5)
885
and condition. Capacities must be reduced for
16 lower tire inflation pressures. See lifting capacity
(15)
chart for tire used. Damaged tires are hazardous to
0.1A (kg) 300 280 265 255
safe operation of crane.
Minimum boom angle (°) for indicated
length (no load)
0 9. Creep - not over 61 m of movement in any 30
Maximum boom length (m) at 0° boom minute period and not exceeding 1.6 km/h.
angle (no load)
18.3
NOTE: ( ) Boom angles are in degrees.
#LMI operating code. Refer to LMI manual for
operating instructions.
Lifting Capacities at 0° Boom Angle
On Rubber - Pick & Carry
Boom Main Boom Length in Meters
Angle 8.8 12.2 15.2 18.3
4,965 2,445 1,400 785
0 deg.
(6.9) (10.3) (13.4) (16.4)
NOTE: ( ) Reference radii in meters
A6-829-100566C
RT530E-2 - S/N 258036 11
RATED LIFTING CAPACITIES IN KILOGRAMS
8.8 m - 29.0 m BOOM
ON OUTRIGGERS 50% EXTENDED (4.3 m SPREAD) - 360°
Radius #4001
in Main Boom Length in Meters
Meters
8.8 12.2 15.2 18.3 21.3 24.4 27.4 29.0
27,000 21,750 20,400
3
(61) (70) (74.5)
24,200 21,750 20,375
3.5
(57) (67.5) (72.5)
22,050 20,325 18,750 *16,775
4
(53) (64.5) (70.5) (76)
18,550 17,050 15,875 14,875 *11,250
4.5
(48.5) (62) (68.5) (72.5) (76)
15,700 14,600 13,700 12,925 10,600 *9,525
5
(43.5) (59) (66) (71) (74) (76)
11,200 11,150 10,625 10,100 9,650 8,580 *7,375
6
(31.5) (53.5) (62) (67.5) (71) (74) (76)
8,405 8,445 8,190 7,855 7,475 6,780 *6,395
7
(47) (57.5) (64) (68) (71.5) (74) (76)
9
See
Note 16
6,595
(39.5)
5,315
(30.5)
6,645
(52.5)
5,370
(47.5)
366,725 6,530 6,295
(60) (65) (69)
5,455 5,520 5,335
(56.5) (62) (66)
6,070
(72)
5,155
(69.5)
5,900
(73)
5,070
(71)
4,345 4,420 4,510 4,465 4,565 4,425 4,355
10
80
(17) (42) (52.5) (59) (63.5) (67.5) (69)
3,100 3,195 3,230 3,275 3,320 3,275
12
(27.5) (43.5) (52) (58) (62.5) (64.5)
2,320 2,345 2,375 2,410 2,430
14
(32.5) (44.5) (52) (57.5) (60)
1,690 1,715 1,775 1,760 1,775
25
16
(15) (36) (45.5) (52.5) (55)
1,240 1,255 1,275 1,285
18
(24) (38) (46.5) (50)
885 895 905
20
(29) (40) (44)
580 595 600
22
(14.5) (32.5) (37.5)
0.1A (kg) 300 280 265 255 250 245 245 240
Minimum boom angle (°) for indicated length (no load) 15 20
Maximum boom length m) at 0° boom angle (no load) 24.4
NOTE: ( ) Boom angles are in degrees.
#LMI operating code. Refer to LMI manual for operating instructions.
*This capacity is based on maximum boom angle.
Lifting Capacities at Zero Degree Boom Angle
On Outriggers 50% Extended - 360°
Boom Main Boom Length in Meters
Angle 8.8 12.2 15.2 18.3 21.3 24.4
8,540 4,080 2,450 1,580 955 510
0 deg.
(6.9) (10.3) (13.4) (16.4) (19.5) (22.5)
NOTE: ( ) Reference radii in meters A6-829-100582B
RT530E-2 - S/N 258036 12
7.9 m - 13.7 m TELE BOOM EXTENSION
22
24
(57)
555
(53.5)
(62)
790
(58)
515
(63.5)
835
(60.5)
600
36
(71.5)
1,155
(68.5)
965
occurs rapidly and without advance warning.
4. Boom angle is the angle above or below horizon-
tal of the longitudinal axis of the boom base
(53.5) (57) (65) section after lifting rated load.
720
80
26 5. Capacities listed are with outriggers properly
(61.5)
extended and vertical jacks set only.
505
28
(57.5)
0.1A (kg) 260 245 230 210
Min. boom angle
25
Radius #8001
in Main Boom Length in Meters
Meters
8.8 12.2 15.2 18.3 21.3 24.4 27.4 29.0
14,375 13,125 12,100
3
(61) (70) (74.5)
11,625 10,850 10,125
3.5
(57) (67.5) (72.5)
9,655 9,165 8,620 *8,105
4
(53) (64.5) (70.5) (76)
8,155 7,820 7,435 7,035 *6,660
4.5
(48.5) (62) (68.5) (72.5) (76)
6,895 6,750 6,490 6,165 5,860 *5,570
5
(43.5) (59) (66) (71) (74) (76)
4,990 4,945 4,970 4,835 4,620 4,415 *4,225
6
7
(31.5) (53.5)
See
(47)
(62)
(57.5)
(67.5)
(64)
36
(71)
3,715 3,750 3,810 3,710 3,560
(68)
2,845 2,890 2,960 3,010 2,900
(74)
(71.5)
(76)
3,415
(74)
2,785
*3,340
(76)
2,730
8 Note 16 (39.5) (52.5) (60) (65) (69) (72) (73)
80
2,195 2,250 2,325 2,385 2,375 2,285 2,240
9
(30.5) (47.5) (56.5) (62) (66) (69.5) (71)
1,685 1,755 1,835 1,885 1,930 1,875 1,835
10
(17) (42) (52.5) (59) (63.5) (67.5) (69)
1,040 1,130 1,160 1,200 1,220 1,205
25
12
(27.5) (43.5) (52) (58) (62.5) (64.5)
645 665 690 725 730
14
(32.5) (44.5) (52) (57.5) (60)
0.1A (kg) 300 280 265 255 250 245 245 240
Minimum boom angle (°) for
indicated length (no load)
32 43 51 53 55
Maximum boom length (m) at
0° boom angle (no load)
15.2
NOTE: ( ) Boom angles are in degrees.
#LMI operating code. Refer to LMI manual for operating instructions.
*This capacity is based on maximum boom angle.
Lifting Capacities at Zero Degree Boom Angle
On Outriggers 0% Extended - 360°
Boom Main Boom Length in Meters
Angle 8.8 12.2 15.2
3,770 1,540 670
0 deg.
(6.9) (10.3) (13.4)
NOTE: ( ) Reference radii in meters A6-829-100691
A6-829-104319
24
3,5
2,5
3
4,5
4
22
5
6
7
20
8
9
10
MAXIMUM OUTRIGGER PAD LOADS IN METRIC TONNES
18
12
36
14
16
16
18
20
22
26
80
14
25
12
10
6
0 5 10 15 20 25 30 35
WORKING LOAD IN METRIC TONNES
A6-829-104320
26
3,5
4
3
24
4,5
22
5
MAXIMUM OUTRIGGER PAD LOADS IN METRIC TONNES
20
6
18
36
7
8
16
9
10
80
12
14
16
14
18
22
25
12
10
6
0 5 10 15 20 25 30
WORKING LOAD IN METRIC TONNES
A6-829-104321
20
18
3
3,5
4
MAXIMUM OUTRIGGER PAD LOADS IN METRIC TONNES
4,5
16
5
6
14
36
7
8
9
10
80
12
14
12
25
10
6
0 2 4 6 8 10 12 14 16
WORKING LOAD IN METRIC TONNES
LIFTING SERVICE
SIZE AND GENERAL
(FRONT LOAD TRA TRAVEL EXTENDED
& RANGE CODE TRAVEL
REAR) STATIC, CREEP &
2.5 MPH (4.0 km/h)
20.5x25 24 PR E-3
36 75 (5.2) 70 (4.8)