Professional Documents
Culture Documents
outside
100 2
150
50
www.ubakus.de
1
inside
50 600
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
1 Spruce (50 mm) 2 Rigid panels, EPS (100 mm)
Spruce
structural timber, Rigid panels, EPS Equivalent
insulation thickness
(WLS 040)
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320 340 360 380 mm
08 Ti au ,25 ,1
41 5 ige ub =0 nd =0
N
DI O 9 nied
r e U ta sU
1 4N s au
V
tz an d E V Be nd au sivh
u t n E V ta b s
ch s E
En Bes Neu u Pa
es V Be 0 ,2
m
är EnE 2 16 ba =0 ,15
W 20 EV Neu V U . =0
G n
E 20 n U
GE nM aß us 40
20 ESa elm 5 - Ha KfW
G z 5 r
GE e
Ein fW BW -Lit bau
f W u K eG 3 u
K ba ärm Ne
u
Ne EW
*Vergleich mit dem Höchstwert gemäß GEG 2020 für erstmaligen Einbau, Ersatz oder Erneuerung von Außenwänden (Anlage 7, Zeile 1a,1b). Page 1
All statements without guarantee
Temperature profile
Temperature profile
25 Temperature
20
1 2 Dew point
15
10
Temperature [°C]
5
0
-5
-10
-15
-20 outside
-25
-30
-35
0 20 40 60 80 100 120 140 160
www.ubakus.de inside
Inside 0°C [mm]
www.ubakus.de
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
Outside 50 600
Left:Temperature and dew-point temperature at the place marked in the right figure. The dew-point indicates the
temperature, at which water vapour condensates. As long as the temperature of the component is everywhere above the dew
point, no condensation occurs. If the curves have contact, condensation occurs at the corresponding position.
Right: The component, drawn to scale.
Page 2
All statements without guarantee
Moisture proofing
For the calculation of the amount of condensation water, the component was exposed to the following constant climate for
90 days: inside: 24°C und 20% Humidity; outside: -20°C und 20% Humidity (Climate according to user input).
This component is free of condensate under the given climate conditions.
Humidity
The temperature of the inside surface is 18,9 °C leading to a relative humidity on the surface of 27%.Mould formation is not
expected under these conditions.
The following figure shows the relative humidity inside the component.
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
100 Relative humidity (%)
1 2 saturation point
90
80
Relative humidity (%)
70
60
50
40
30 outside
20
10
0
0 20 40 60 80 100 120 140 160
www.ubakus.de inside
Inside 0°C [mm]
www.ubakus.de Outside 50 600
Notes: Calculation using the Ubakus 2D-FE method. Convection and the capillarity of the building materials
were not considered. The drying time may take longer under unfavorable conditions (shading, damp / cool
summers) than calculated here.
Page 3
All statements without guarantee
Heat protection
The following results are properties of the tested component alone and do not make any statement about the heat protection
of the entire room:
Temperature profile
This document has been generated by the U-value calculator on www.ubakus.de. If you are harmed by the free use of these contents, the service provider is only liable in case of
32
30 1 Spruce (50 mm)
Temperature [°C]
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
16
14
0 20 40 60 80 100 120 140 160
Inside [mm]
www.ubakus.de Outside
The calculations presented above have been created for a 1-dimensional cross-section of the component.
Page 4