Professional Documents
Culture Documents
Vent Fan 1
Vent Fan 1
1 Actual values
1 Motor speed rpm 0.00 rpm -30000.00 30000.00
2 Motor speed % 0.00 % -1000.00 1000.00
3 Output frequency 0.00 Hz -30000.00 30000.00
4 Motor current 0.00 A 0.00 30000.00
5 Motor current % 0.0 % 0.0 1000.0
6 Motor torque 0.0 % -1600.0 1600.0
7 Dc-voltage 584.99 V 0.00 2000.00
8 Encoder1 speed 0.00 rpm -32768.00 32768.00
9 Encoder1 pos 0.00000000 rev 0.00000000 1.00000000
10 Encoder2 speed 0.00 rpm -32768.00 32768.00
11 Encoder2 pos 0.00000000 rev 0.00000000 1.00000000
12 Pos act 0.000 rev -32768.000 32768.000
13 Pos 2nd enc 0.000 rev -32768.000 32768.000
14 Motor speed est 0.00 rpm -30000.00 30000.00
15 Temp inverter 28.8 % -40.0 160.0
16 Temp brk chopper 11.5 % -40.0 160.0
17 Motor temp1 20.0 C -10.0 250.0
18 Motor temp2 20.0 C -10.0 250.0
19 Used supply volt 415.3 V 0.0 1000.0
20 Brake res load 0 % 0 1000
21 Cpu usage 78 % 0 100
22 Power inu out 0.00 kW -32768.00 32768.00
23 Motor power 0.00 kW -32768.00 32768.00
24 kWh inverter 1304 kWh 0 2147483647
25 kWh supply 1302 kWh -2147483647 2147483647
26 On-time counter 485.83 h 0.0 35791394.1
27 Run-time counter 141.08 h 0.0 35791394.1
28 Fan on-time 143.83 h 0.0 35791394.1
29 Torq nom scale 1446.862 Nm 0.000 2147483.647
30 Polepairs 3 0 1000
31 Mech time const 0.000 s 0.000 32767.000
32 Temp phase A 37.6 % -40.0 160.0
33 Temp phase B 37.6 % -40.0 160.0
34 Temp phase C 37.6 % -40.0 160.0
35 Saved energy 19869 kWh 0 2147483647
36 Saved amount 129.14 gbp 0.00 21474836.47
37 Saved CO2 9.9 tonne 0.0 214748364.7
38 Temp int board 45.3 C -40.0 160.0
39 Output voltage 0.0 V 0.0 1000.0
40 Speed filt 0.0 rpm -30000.0 30000.0
41 Torque filt 0.0 % -1600.0 1600.0
42 Fan start count 87 0 2147483647
2 I/O values
1 DI status 0b001100100 0b000000000 0b111111111
2 RO status 0b00000001 0b00000000 0b11111111
3 DIO status 0b0000000001 0b0000000000 0b1111111111
4 AI1 4.748 mA -22.000 22.000
5 AI1 scaled 47.680 -32768.000 32768.000
6 AI2 -0.016 mA -22.000 22.000
7 AI2 scaled 749.837 -32768.000 32768.000
8 AI3 0.000 mA -22.000 22.000
9 AI3 scaled 0.000 -32768.000 32768.000
10 AI4 0.000 mA -22.000 22.000
11 AI4 scaled 0.000 -32768.000 32768.000
12 AI5 0.000 mA -22.000 22.000
13 AI5 scaled 0.000 -32768.000 32768.000
14 AI6 0.000 mA -22.000 22.000
15 AI6 scaled 0.000 -32768.000 32768.000
3 Control values
3 SpeedRef unramp 47.68 rpm -30000.00 30000.00
5 SpeedRef ramped 0.00 rpm -30000.00 30000.00
6 SpeedRef used 48.00 rpm -30000.00 30000.00
7 Speed error filt 0.00 rpm -30000.00 30000.00
8 Acc comp torq 0.0 % -1600.0 1600.0
9 Torq ref sp ctrl 0.2 % -1600.0 1600.0
11 Torq ref ramped 0.0 % -1000.0 1000.0
12 Torq ref sp lim 0.0 % -1000.0 1000.0
13 Torq ref to TC 0.0 % -1600.0 1600.0
14 Torq ref used 0.0 % -1600.0 1600.0
15 Brake torq mem Close % -1000.0 1000.0
16 Brake command 0 0 1
17 Flux actual 0 % 0 200
18 Speed ref pot 0.00 rpm -30000.00 30000.00
20 Max speed ref 1000.00 rpm -30000.00 30000.00
21 Min speed ref 0.00 rpm -30000.00 30000.00
4 Appl values
1 Process act1 100.00 -32768.00 32768.00
2 Process act2 100.00 -32768.00 32768.00
3 Process act 100.00 -32768.00 32768.00
4 Process PID err 0.0 -32768.0 32768.0
5 Process PID out 0.0 -32768.0 32768.0
6 Process var1 0.000 % -32768.000 32768.000
7 Process var2 0.000 % -32768.000 32768.000
8 Process var3 0.000 % -32768.000 32768.000
9 Counter ontime1 508140 s 0 2147483647
10 Counter ontime2 1749498 s 0 2147483647
11 Counter edge1 42 0 2147483647
12 Counter edge2 88 0 2147483647
13 Counter value1 3158752 0 2147483647
14 Counter value2 3158823 0 2147483647
5 Actual Value
1 Actual Current 0.0 A -32768.0 32768.0
2 Actual Current 2 0.0 A -32768.0 32768.0
3 Power KW 0.0 kW -32768.0 32768.0
4 Invertor Power 0.0 kW -32768.0 32768.0
6 Drive status
1 Status word1 0x1103 0x0000 0xFFFF
9 System info
1 Drive type ACS850 0 65535
2 Drive rating id ACS850_290A 0 65535
3 Firmware ID UIFI 0x00000000 0xFFFFFFFF
4 Firmware ver 0x2600 0x0000 0xFFFF
5 Firmware patch 0 0 4294967295
10 Int logic ver 0x1012 0x0000 0xFFFF
11 Slot 1 VIE name EMPTY 0x0000 0xFFFF
12 Slot 1 VIE ver 0x0000 0x0000 0xFFFF
13 Slot 2 VIE name VIE 4 0x0000 0xFFFF
14 Slot 2 VIE ver 0x1100 0x0000 0xFFFF
20 Option slot1 No option 0 24
21 Option slot2 FIO-11 0 24
22 Option slot3 FPBA-01 0 23
10 Start/stop/dir
1 Ext1 start func In1 0 7
2 Ext1 start in1 DI1
3 Ext1 start in2 C.False
4 Ext2 start func In1 0 7
5 Ext2 start in1 DI1
6 Ext2 start in2 C.False
7 Jog1 start C.False
8 Jog2 start C.False
9 Jog enable C.False
10 Fault reset sel C.False
11 Run enable DI6
13 Em stop off3 C.True
15 Em stop off1 C.True
17 Start enable C.True
19 Start inhibit Disabled 0 1
20 Start intrl func Off3 stop 0 1
11 Start/stop mode
1 Start mode Automatic 0 2
2 Dc-magn time 500 ms 0 10000
3 Stop mode Coast 1 2
4 Dc hold speed 5.0 rpm 0.0 1000.0
5 Dc hold curr ref 30 % 0 100
6 Dc hold C.False
7 Autophasing mode Turning 0 2
12 Operating mode
1 Ext1/Ext2 sel DI3
3 Ext1 ctrl mode Speed 1 5
5 Ext2 ctrl mode Speed 1 5
7 Local ctrl mode Speed 1 2
13 Analogue inputs
1 AI1 filt time 0.100 s 0.000 30.000
2 AI1 max 20.000 mA -22.000 22.000
3 AI1 min 4.000 mA -22.000 22.000
4 AI1 max scale 1000.000 -32768.000 32768.000
5 AI1 min scale 0.000 -32768.000 32768.000
6 AI2 filt time 0.100 s 0.000 30.000
7 AI2 max 10.000 mA -22.000 22.000
8 AI2 min -10.000 mA -22.000 22.000
9 AI2 max scale 1500.000 -32768.000 32768.000
10 AI2 min scale 0.000 -32768.000 32768.000
11 AI3 filt time 0.100 s 0.000 30.000
12 AI3 max 22.000 mA -22.000 22.000
13 AI3 min 4.000 mA -22.000 22.000
14 AI3 max scale 1500.000 -32768.000 32768.000
15 AI3 min scale 0.000 -32768.000 32768.000
16 AI4 filt time 0.100 s 0.000 30.000
17 AI4 max 22.000 mA -22.000 22.000
18 AI4 min 4.000 mA -22.000 22.000
19 AI4 max scale 1500.000 -32768.000 32768.000
20 AI4 min scale 0.000 -32768.000 32768.000
21 AI5 filt time 0.100 s 0.000 30.000
22 AI5 max 22.000 mA -22.000 22.000
23 AI5 min 4.000 mA -22.000 22.000
24 AI5 max scale 1500.000 -32768.000 32768.000
25 AI5 min scale 0.000 -32768.000 32768.000
26 AI6 filt time 0.100 s 0.000 30.000
27 AI6 max 22.000 mA -22.000 22.000
28 AI6 min 4.000 mA -22.000 22.000
29 AI6 max scale 1500.000 -32768.000 32768.000
30 AI6 min scale 0.000 -32768.000 32768.000
31 AI tune No action 0 4
32 AI superv func No 0 3
33 AI superv cw 0b0000 0b0000 0b1111
14 Digital I/O
1 DI invert mask 0b000000000 0b000000000 0b111111111
2 DIO1 conf Output 0 2
3 DIO1 out src Ready relay
4 DIO1 Ton 0.0 s 0.0 3000.0
5 DIO1 Toff 0.0 s 0.0 3000.0
6 DIO2 conf Output 0 3
7 DIO2 out src RunningRelay
8 DIO2 Ton 0.0 s 0.0 3000.0
9 DIO2 Toff 0.0 s 0.0 3000.0
10 DIO3 conf Output 0 1
11 DIO3 out src Fault(-1)
14 DIO4 conf Output 0 1
15 DIO4 out src Ready relay
18 DIO5 conf Output 0 1
19 DIO5 out src Ref running
22 DIO6 conf Output 0 1
23 DIO6 out src Fault
26 DIO7 conf Output 0 1
15 Analogue outputs
1 AO1 src Speed rpm
2 AO1 filt time 0.100 s 0.000 30.000
3 AO1 out max 20.000 mA 0.000 22.700
4 AO1 out min 4.000 mA 0.000 22.700
5 AO1 src max 1500.000 -32768.000 32768.000
6 AO1 src min 0.000 -32768.000 32768.000
7 AO2 src Current
8 AO2 filt time 0.100 s 0.000 30.000
9 AO2 out max 20.000 mA 0.000 22.700
10 AO2 out min 4.000 mA 0.000 22.700
11 AO2 src max 250.000 -32768.000 32768.000
12 AO2 src min 0.000 -32768.000 32768.000
13 AO3 src Power motor
14 AO3 filt time 0.100 s 0.000 30.000
15 AO3 out max 20.000 mA 0.000 22.700
16 AO3 out min 4.000 mA 0.000 22.700
17 AO3 src max 150.000 -32768.000 32768.000
18 AO3 src min 0.000 -32768.000 32768.000
19 AO4 src Frequency
20 AO4 filt time 0.100 s 0.000 30.000
21 AO4 out max 22.000 mA 0.000 22.700
22 AO4 out min 4.000 mA 0.000 22.700
23 AO4 src max 50.000 -32768.000 32768.000
24 AO4 src min 0.000 -32768.000 32768.000
25 AO ctrl word 0b000000 0b000000 0b111111
30 AO calibration No action 0 4
16 System
1 Local lock C.False
2 Parameter lock Open 0 2
3 Pass code 0 0 2147483647
4 Param restore Done 0 2
7 Param save Done 0 1
9 User set sel No request 1 10
10 User set log N/A 0 4294967295
19 Speed calculation
1 Speed scaling 1000 rpm 0 30000
2 Speed fb sel Estimated 0 2
3 MotorSpeed filt 8.000 ms 0.000 10000.000
6 Zero speed limit 30.00 rpm 0.00 30000.00
7 Zero speed delay 0 ms 0 30000
8 Above speed lim 0 rpm 0 30000
9 Speed TripMargin 500.0 rpm 0.0 10000.0
10 Speed window 100 rpm 0 30000
13 Speed fbk fault Fault 0 2
14 Speed superv est 450.00 rpm 0.00 30000.00
15 Speed superv enc 15.00 rpm 0.00 30000.00
16 Speed fb filt t 15.000 ms 0.000 10000.000
20 Limits
1 Maximum speed 1000 rpm -30000 30000
2 Minimum speed 0 rpm -30000 30000
3 Pos speed ena C.True
4 Neg speed ena C.True
5 Maximum current 280.00 A 0.00 30000.00
6 Torq lim sel C.False
7 Maximum torque1 300.0 % 0.0 1600.0
8 Minimum torque1 -300.0 % -1600.0 0.0
9 Maximum torque2 Max torque1
10 Minimum torque2 Min torque1
12 P motoring lim 300.0 % 0.0 1600.0
13 P generating lim 300.0 % 0.0 1600.0
21 Speed ref
1 Speed ref1 sel Mot pot
2 Speed ref2 sel AI1 scaled
3 Speed ref1 func Ref1 0 5
4 Speed ref1/2 sel DI3
5 Speed share 1.000 -8.000 8.000
7 Speed ref jog1 0 rpm -30000 30000
8 Speed ref jog2 0 rpm -30000 30000
9 SpeedRef min abs 0 rpm 0 30000
10 Mot pot func Reset 0 1
11 Mot pot up DI4
12 Mot pot down DI5
23 Speed ctrl
1 Proport gain 10.00 0.00 200.00
2 Integration time 0.500 s 0.000 600.000
3 Derivation time 0.000 s 0.000 10.000
4 Deriv filt time 8.0 ms 0.0 1000.0
5 Acc comp DerTime 0.00 s 0.00 600.00
6 Acc comp Ftime 8.0 ms 0.0 1000.0
7 Speed err Ftime 0.0 ms 0.0 1000.0
8 Speed additive Zero
9 Max torq sp ctrl 300.0 % -1600.0 1600.0
10 Min torq sp ctrl -300.0 % -1600.0 1600.0
11 SpeedErr winFunc Disabled 0 2
12 SpeedErr win hi 0 rpm 0 3000
13 SpeedErr win lo 0 rpm 0 3000
14 Drooping rate 0.00 % 0.00 100.00
15 PI adapt max sp 0 rpm 0 30000
16 PI adapt min sp 0 rpm 0 30000
17 Pcoef at min sp 1.000 0.000 10.000
18 Icoef at min sp 1.000 0.000 10.000
20 PI tune mode Done 0 4
21 Tune bandwidth 100.00 Hz 0.00 2000.00
22 Tune damping 0.5 0.0 200.0
24 Torque ref
1 Torq ref1 sel AI2 scaled
2 Torq ref add sel Zero
3 Maximum torq ref 300.0 % 0.0 1000.0
4 Minimum torq ref -300.0 % -1000.0 0.0
5 Load share 1.000 -8.000 8.000
6 Torq ramp up 0.000 s 0.000 60.000
7 Torq ramp down 0.000 s 0.000 60.000
25 Critical speed
1 Crit speed sel Disable 0 1
2 Crit speed1 lo 0 rpm -30000 30000
3 Crit speed1 hi 0 rpm -30000 30000
4 Crit speed2 lo 0 rpm -30000 30000
5 Crit speed2 hi 0 rpm -30000 30000
6 Crit speed3 lo 0 rpm -30000 30000
7 Crit speed3 hi 0 rpm -30000 30000
26 Constant speeds
1 Const speed func 0b011 0b000 0b111
2 Const speed sel1 C.False
3 Const speed sel2 C.False
4 Const speed sel3 C.False
6 Const speed1 0 rpm -30000 30000
7 Const speed2 0 rpm -30000 30000
8 Const speed3 0 rpm -30000 30000
9 Const speed4 0 rpm -30000 30000
10 Const speed5 0 rpm -30000 30000
11 Const speed6 0 rpm -30000 30000
12 Const speed7 0 rpm -30000 30000
27 Process PID
1 PID setpoint sel AI1 scaled
2 PID fbk func Act1 0 8
3 PID fbk1 src AI2 scaled
4 PID fbk2 src AI2 scaled
5 PID fbk1 max 100.00 -32768.00 32768.00
6 PID fbk1 min -100.00 -32768.00 32768.00
7 PID fbk2 max 100.00 -32768.00 32768.00
30 Fault functions
1 External fault C.True
2 Speed ref safe 0 rpm -30000 30000
3 Panel ctrl loss No 0 3
4 Mot phase loss Fault 0 1
5 Earth fault Fault 0 2
6 Suppl phs loss Fault 0 1
7 Sto diagnostic Fault 1 4
8 Wiring or earth No 0 1
9 Stall function 0b111 0b000 0b111
10 Stall curr lim 200.0 % 0.0 1600.0
11 Stall freq hi 15.0 Hz 0.5 1000.0
12 Stall time 20 s 0 3600
32 Automatic reset
1 Autoreset sel 0b000000 0b000000 0b111111
2 Number of trials 0 0 5
3 Trial time 30.0 s 1.0 600.0
4 Delay time 0.0 s 0.0 120.0
33 Supervision
1 Superv1 func Disabled 0 4
2 Superv1 act Speed rpm
3 Superv1 hi 0.00 -32768.00 32768.00
4 Superv1 lo 0.00 -32768.00 32768.00
5 Superv2 func Disabled 0 4
35 Process variable
1 Signal1 param Speed %
2 Signal1 max 300.000 -32768.000 32768.000
3 Signal1 min -300.000 -32768.000 32768.000
4 Proc var1 dispf 3 0 5
5 Proc var1 unit 4 0 98
6 Proc var1 max 300.000 -32768.000 32768.000
7 Proc var1 min -300.000 -32768.000 32768.000
8 Signal2 param Current %
9 Signal2 max 300.000 -32768.000 32768.000
10 Signal2 min -300.000 -32768.000 32768.000
11 Proc var2 dispf 3 0 5
12 Proc var2 unit 4 0 98
13 Proc var2 max 300.000 -32768.000 32768.000
14 Proc var2 min -300.000 -32768.000 32768.000
15 Signal3 param Torque
16 Signal3 max 300.000 -32768.000 32768.000
17 Signal3 min -300.000 -32768.000 32768.000
18 Proc var3 dispf 3 0 5
19 Proc var3 unit 4 0 98
20 Proc var3 max 300.000 -32768.000 32768.000
21 Proc var3 min -300.000 -32768.000 32768.000
36 Timed functions
1 Timers enable C.False
2 Timers mode 0b0000 0b0000 0b1111
3 Start time1 00:00:00 00:00:00 00:00:00
38 Flux ref
1 Flux ref 100 % 0 200
3 U/f curve func Linear 0 2
4 U/f curve freq1 10 % 1 500
5 U/f curve freq2 30 % 1 500
6 U/f curve freq3 50 % 1 500
7 U/f curve freq4 70 % 1 500
8 U/f curve freq5 90 % 1 500
9 U/f curve volt1 20 % 0 200
10 U/f curve volt2 40 % 0 200
11 U/f curve volt3 60 % 0 200
12 U/f curve volt4 80 % 0 200
13 U/f curve volt5 100 % 0 200
16 Flux ref pointer P.Flux ref
40 Motor control
1 Motor noise Default 0 3
2 Sf ref 3.0 kHz 1.0 8.0
3 Slip gain 100 % 0 200
4 Voltage reserve -4 % -4 50
6 Force open loop False 0 1
7 IR-compensation 0.00 % 0.00 50.00
8 Ex request Disabled 0 1
10 Flux braking Disabled 0 2
11 Mmodel t adapt Disabled 0 1
14 Rotor time const 100 % 20 500
44 Maintenance
1 Ontime1 func 0b001 0b000 0b111
2 Ontime1 src Running
3 Ontime1 limit 36000000 s 0 2147483647
4 Ontime1 alm sel Mot bearing 0 5
5 Ontime2 func 0b001 0b000 0b111
6 Ontime2 src Charged
7 Ontime2 limit 15768000 s 0 2147483647
8 Ontime2 alm sel Device clean 0 5
9 Edge count1 func 0b001 0b000 0b111
10 Edge count1 src Charged
11 Edge count1 lim 5000 0 2147483647
12 Edge count1 div 1 1 2147483647
13 Edg cnt1 alm sel Dc-charge 0 5
14 Edge count2 func 0b001 0b000 0b111
15 Edge count2 src RO1
16 Edge count2 lim 10000 0 2147483647
17 Edge count2 div 1 1 2147483647
18 Edg cnt2 alm sel Output relay 0 5
19 Val count1 func 0b001 0b000 0b111
20 Val count1 src Speed rpm
21 Val count1 lim 13140000 0 2147483647
22 Val count1 div 6000 1 2147483647
23 Val cnt1 alm sel Mot bearing 0 1
24 Val count2 func 0b001 0b000 0b111
25 Val count2 src Speed rpm
26 Val count2 lim 6570000 0 2147483647
27 Val count2 div 6000 1 2147483647
28 Val cnt2 alm sel Value2 0 1
29 Fan ontime lim 0.00 h 0.0 35791394.1
30 Runtime lim 0.00 h 0.0 35791394.1
31 Runtime alm sel Device clean 1 5
32 kWh inv lim 0 kWh 0 2147483647
33 kWh inv alm sel Device clean 1 5
34 Counter reset C.False
45 Energy optimising
1 Energy optim Disable 0 1
2 Energy tariff1 0.65 gbp 0.00 21474836.47
6 E tariff unit Local 0 2
7 CO2 Conv factor 0.5 0.0 10.0
8 Reference power 100.0 % 0.0 1000.0
9 Energy reset Done 0 1
47 Voltage ctrl
1 Overvolt ctrl Enable 0 1
2 Undervolt ctrl Enable 0 1
3 SupplyVoltAutoId Enable 0 1
4 Supply voltage 400.0 V 0.0 1000.0
48 Brake chopper
1 Bc enable Disable 0 2
2 Bc run-time ena Running
3 BrThermTimeConst 0 s 0 10000
4 Br power max cnt 0.0 kW 0.0 10000.0
5 R br 0.0 Ohm 0.0 1000.0
6 Br temp faultlim 105 % 0 150
7 Br temp alarmlim 95 % 0 150
49 Data storage
1 Data storage1 0 -32768 32767
50 Fieldbus
1 Fba enable Enable 0 1
2 Comm loss func No 0 3
3 Comm loss t out 0.3 s 0.3 6553.5
4 Fb ref1 modesel Speed 0 6
5 Fb ref2 modesel Torque 0 6
6 Fb act1 tr src P.Motor speed rpm
7 Fb act2 tr src P.Motor torque
8 Fb sw bit12 src C.False
9 Fb sw bit13 src C.False
10 Fb sw bit14 src C.False
11 Fb sw bit15 src C.False
12 FB comm speed Normal 0 2
15 Fb cw used P.FBA main cw
20 Fb main sw func 0b011 0b000 0b111
51 FBA settings
1 FBA type Profibus-DP 0 65535
2 FBA par2 3 0 65535
3 FBA par3 1500 0 65535
4 FBA par4 5 0 65535
5 FBA par5 1 0 65535
6 FBA par6 99 0 65535
7 FBA par7 0 0 65535
8 FBA par8 0 0 65535
9 FBA par9 0 0 65535
10 FBA par10 0 0 65535
11 FBA par11 0 0 65535
12 FBA par12 0 0 65535
13 FBA par13 0 0 65535
14 FBA par14 0 0 65535
15 FBA par15 0 0 65535
16 FBA par16 0 0 65535
17 FBA par17 0 0 65535
18 FBA par18 0 0 65535
19 FBA par19 0 0 65535
20 FBA par20 0 0 65535
21 FBA par21 1 0 65535
22 FBA par22 0 0 65535
23 FBA par23 0 0 65535
24 FBA par24 0 0 65535
25 FBA par25 0 0 65535
26 FBA par26 0 0 65535
27 FBA par refresh DONE 0 1
28 Par table ver 0x0102 0x0000 0xFFFF
29 Drive type code 540 0 65535
30 Mapping file ver 3 0 65535
31 D2FBA comm sta On-line 0 6
32 FBA comm sw ver 0x3132 0x0000 0xFFFF
33 FBA appl sw ver 0x2161 0x0000 0xFFFF
52 FBA data in
1 FBA data in1 4 0 9999
2 FBA data in2 5 0 9999
3 FBA data in3 501 0 9999
56 Panel display
1 Signal1 param P.Speed filt
2 Signal2 param P.Motor current
3 Signal3 param P.Torque filt
4 Signal1 mode Normal -1 3
5 Signal2 mode Normal -1 3
6 Signal3 mode Normal -1 3
7 Panel ref unit rpm 0 1
8 Speed filt time 250.0 ms 0.0 10000.0
9 Torque filt time 100.0 ms 0.0 10000.0
12 Panel ref copy Disabled 0 1
57 D2D communication
1 Link mode Disabled 0 2
2 Comm loss func Alarm 0 2
3 Node address 1 1 62
4 Follower mask 1 0x00000000 0x00000000 0xFFFFFFFF
5 Follower mask 2 0x00000000 0x00000000 0xFFFFFFFF
6 Ref 1 src P.SpeedRef ramped
7 Ref 2 src P.Torq ref to TC
8 Follower cw src P.D2D follower cw
11 Ref1 msg type Broadcast 0 1
12 Ref1 mc group 0 0 62
13 Next ref1 mc grp 0 0 62
14 Nr ref1 mc grps 1 1 62
15 D2D com port on-board 0 3
58 Embedded Modbus
1 Protocol ena sel Disabled 0 1
3 Node address 1 0 247
4 Baud rate 9600 0 6
5 Parity 8 none 1 0 3
6 Control profile ABB Enhanced 0 3
7 Comm loss t out 600 0 60000
8 Comm loss mode None 0 2
9 Comm loss action None 0 3
10 Refresh settings Done 0 1
11 Reference scale 100 1 65535
12 EFB comm speed Low 0 1
64 Load analyzer
1 PVL signal Power inu
2 PVL filt time 2.00 s 0.00 120.00
3 Reset loggers C.False
4 AL signal Power motor
5 AL signal base 100.00 0.00 32768.00
6 PVL peak value1 51.81 -32768.00 32768.00
7 Date of peak 01 Jan 1980 31 Dec 1979 30 Dec 1979
8 Time of peak 05:42:19 00:00:00 2147483647
9 Current at peak 144.64 A -32768.00 32768.00
10 Dc volt at peak 559.58 V 0.00 2000.00
11 Speed at peak 603.6 rpm -32768.0 32768.0
12 Date of reset 31 Dec 1979 31 Dec 1979 30 Dec 1979
13 Time of reset 00:00:00 00:00:00 2147483647
14 AL1 0 to 10% 71.17 % 0.00 1.00
15 AL1 10 to 20% 19.30 % 0.00 1.00
16 AL1 20 to 30% 9.23 % 0.00 1.00
17 AL1 30 to 40% 0.18 % 0.00 1.00
18 AL1 40 to 50% 0.07 % 0.00 1.00
19 AL1 50 to 60% 0.04 % 0.00 1.00
20 AL1 60 to 70% 0.01 % 0.00 1.00
74 Appl programming
1 SpeedRef ramp in P.SpeedRef unramp
2 SpeedRef nctrl P.SpeedRef ramped
3 Speed fbk nctrl P.Motor speed rpm
4 Speed err nctrl P.Speed error filt
5 Acc comp src P.Acc comp torq
6 Tref speed src P.Torq ref sp ctrl
7 Tref torq src P.Torq ref sp lim
9 D2D cw used P.D2D main cw
10 PID fbk src P.Process act
92 Resolver conf
1 Resolv polepairs 1 1 32
2 Exc signal ampl 4.0 Vrms 4.0 12.0
3 Exc signal freq 1 kHz 1 20
94 Ext IO conf
1 Ext IO1 sel FIO-11 0 4
2 Ext IO2 sel None 0 4
95 Hw configuration
1 Ctrl boardSupply Internal 24V 0 1
3 Temp inu ambient 40 C 0 55
99 Start-up data
1 Language English 0x0000 0xFFFF
4 Motor type AM 0 1
5 Motor ctrl mode DTC 0 1
6 Mot nom current 257.0 A 48.3 580.0
7 Mot nom voltage 415.0 V 80.0 960.0
8 Mot nom freq 50.0 Hz 5.0 500.0
9 Mot nom speed 990 rpm 0 30000
10 Mot nom power 150.00 kW 0.00 10000.00
11 Mot nom cosfii 0.00 0.00 1.00
12 Mot nom torque 0.000 Nm 0.000 2147483.647
13 IDrun mode No 0 6
16 Phase inversion No 0 1