Professional Documents
Culture Documents
Safety Relay Modules
Safety Relay Modules
KG
Safety Relay
Modules
Catalogue SRB-G
S RB-
odules -47
: M -46,
New4, -45,
C.4 L1
OPEN
****
CLOSED
KB
Reset
KA
47 57
C C1 X2 X2.1 S1 X1 S2 13 23 33 (43) (53)
F2 K1 K2
* Trigger K1
F1 circuit
K1 KA
K3 K4 K3
TIMER TIMER
K2
K2 KB
K1 K3 K2 K4 K4
D D1 L62 14 24 34 48 58
(44) (54)
KA KB
e n t all y c o m
o nm p
N
at
r
vi
ib
En
le
p er
m ad
pa
e
ro
f
m le
100% r ec y c
Contents Page
General 3
1 New products:
– SRB-C.44, -C.45, -C.46, -C.47 6
2 SRB modules 22.5 mm wide
– STOP category 0 25
3 SRB modules 22.5 mm wide
– STOP category 1 47
4 SRB modules 45 mm wide
– Standard version, STOP category 0 53
5 SRB modules 45 mm wide
– Standard version, STOP category 1 67
6 SRB modules 45 mm wide
– Multifunctional version, STOP category 0 73
7 SRB modules 45 mm wide
– Multifunctional version, STOP category 1 87
8 SRB modules 45 mm wide
– Special versions 101
9 SRB modules 90 mm wide
– Standard version 111
10 SRB modules 90 mm wide
– Special versions 117
11 Modules for contact multiplying 143
We accept no liability for errors. Or as the ancient Greeks already knew: The descriptions, control relationships,
Technical data subject to change without data on external actuators, notes on
The Gods do not reveal everything to installation and operation etc. are
notice. The data quoted in this list are
mortals right at the start. But we find out provided on the best of our knowledge.
typical series values which have been
what is better during the course of time This does not however mean that any
carefully checked.
by searching. warranted characteristics or other claims
Xenophanes (Greek philosopher, born relevant to liability over and above the
570/588 BC) "General Terms and Conditions for
Supply of Goods and Services from the
Electrical Industry" can be deduced from
them. The user is not therefore released
from the obligation to check our data and
recommendations for his own use prior to
operation. We trust this will be under-
stood and this note observed.
1
2
Safety Relay Modules
Guide to Products SRB
3
General
Compact The significant feature of in this Furthermore in housings with Modules which are not listed in this
housings latest issue described Safety Relay 45 mm width modules with addi- guide, in particular older SRB
Modules (or SRB modules) is tional setting and adjustment modules are still on sale. Please ask
highlighting the advantage of advantages are available and also for extra data sheet.
increased functionality, but with modules for some special applica-
reduced space consumption. tions. Some exceptions are realized
in 90 mm housings.
Standard modules, some with
additional technical features are Parallel to these standard housings
offered in housings, 22.5 mm wide also the product family SRBF –
only and 45 mm wide. modules in special housings, 36 mm
wide – will be continued
Advantages Safety Relay Modules in ready-to- Because of the ready-to-install The use of Safety Relay Modules is
install compact housings with snap compact housings Safety Relay saving significantly time for wiring.
on fixing are containing a fail-safe Modules can be placed directly into Furthermore errors in design state
and error tolerant electric circuit, the control cabinet very simple and and errors during wiring are
designed to meet the requirements space saving. eliminated and therefore no extra
of control category 3 and/or 4 time for trouble shooting and repair
(EN 954-1), depending on the needs to be considered.
external wiring.
4
Approvals
ÜFZ
PR
ER
BG-
T.
ÜFZ
PR
ER
BG-
T.
ET
BIA
Certifications of all essential SRB For SRB modules test certificates ● Berufsgenossenschaftliches
basic circuits issued by component from the following authorities have Institut für Arbeitssicherheit
test-authorities provide the user with been issued (for details see technical BIA, St. Augustin,
extra security ensuring that this data):
obligations in respect to product ● Canadian Standard Association
liability are fulfilled. ● Prüfstelle der BG Feinmechanik CSA,
und Elektrotechnik, Cologne,
● Underwriters Laboratories
Inc.UL.
Determination Although all SRB circuits meet the The scope below shall give assis- For better transparency the follow-
specific requirements related to the tance in selecting the appropriate ing illustration and technical data are
protection in case of failures module. filed on the basis of general charac-
(EN 60 204-1 : 1998-11, part 9.4) teristics and functions, but not
the various models differ in some following the historic sequential
important details. number allocation C.XX.
5
New products:
6 6
New products: 1
Functional sequence
Closing release:
1. Release is open 2. Relay contacts close 3. Semi-conductor switches
voltage-free => release is closed
13 13 13
14 14 14
Opening release:
1. Release is kept open 2. Relay contacts are
by the semi-conductor opened voltage-free
13 13
14 14
7
SRB-C.44
Safety relay array for emergency stop devices,
interlocking devices and others
☛ 2-channel triggering ☛ Cross-short recognition
☛ Non-equivalent inputs ☛ 22.5 mm housing
☛ Current limitation at input circuits
☛ Voltage limitation at input circuits
☛ Selectable extras:
– Trailing edge function
– Auto reset
Features – Relay output: 3 NO, 1 NC – Feedback loop – Housing 45 mm, made of
(Auxiliary NC for monitoring thermoplastic in accordance with
must not be used in safety – Input for emergency stop UL-94-V-0, red RAL 3000
enabling circuits!) or door monitoring
– DIN rail mounting
– Input for reset – LED’s for K1, K2, Ui DIN EN 50 022
Approvals
ÜFZ
PR
ER
BG-
T.
Front view
13 23 33 L42
A1 X1 X2 X3
K1
Ui
SRB-C.44 K2
A2 S21 S22 S14
14 24 34 S13
8
SRB-C.44 (continued) 1
Ui
K2 KB
K1 K2
A2 14 24 34 L42
KA KB
N
For further examples
refer to page 10/11
Model specific
Operating voltage 24VDC –15%/+20%, residual ripple max. 10%
Technical data
24 VAC –15%/+10%
(refer to page 157
for general data) Frequency 50/60 Hz (for AC operating)
Fuse (power supply) T 0.5 A/250 V (internal electronic fuse, triggering current > 0.6 A,
reset after 1 second)
Power consumption max. 1.8 W; 2.4 VA, plus auxiliary output L42
Switching capacity (enabling contacts) 230 VAC, 4 A ohmic (inductive with suitable suppression)
Fuse (enabling contacts) 4 A slow blowing
Switching capacity (monitoring contacts) 24 VDC, 100 mA
Current and voltage limitation of input circuits 26 VDC/100 mA
Application category AC 15/DC 13, DIN VDE 0660 Part 200
Pick-up delay ≤ 120 ms/≤ 30 ms (Auto start, reset button)
Drop-out delay ≤ 20 ms
Contact material / contacts AgSnO, self cleaning, positively driven
Contact resistance max. 100 mOhm when new
Air and creeping distances DIN VDE 0110-1 (04.97), 4 kV/2
Connections Self lifting screw terminals min. 0.6 qmm, max. 2.5 qmm
Dimensions H/W/D 90 mm/22.5 mm/121 mm
Weight 235 g
Ambient operating temperature –25 °C ... +45 °C (derating curve available)
Mechanical life 107 switching cycles
Terminal labeling DIN EN 50 005/DIN 50 013
9
SRB-C.44 (continued)
S22 S14 X2
Safety category 3 or 4
S22 S14 X2
in accordance with
EN 954-1.
Advice:
For "Automatic Reset" X1 X1
connect feed back loop to X1-
X3 or apply jumper X1-X3 if
no feed back loop is used.
When using external reset
button (feed back loop
connected to X1-X2), unit is RESET
triggered by trailing edge
function. KA
KA
Trailing edge function with
"fail-safe" function only by a
DC power supply. KB
KB
After a performed "Emer-
gency Shut Down" an auto-
matic restart of the system
must be prevented by the
higher ranking electric
circuitry when the relay X2 X3
module SRB-C.44/e is been
set into mode "Auto-matic
Start" (refer to EN 60 204-1,
part 9.2.5.4.2 and part 10.8.3).
10
SRB-C.44 (continued) 1
14 KB
KB 14
14 24
24 KA
KA
KA
KA KB
KB KA KB
N N
N N
11
SRB-C.45
Safety relay array for emergency stop devices,
interlocking devices and others
☛ "Long life" module ☛ 45 mm housing
☛ 1- or 2-channel triggering ☛ 1 semiconductor output
☛ 3 enabling outputs and ☛ Selectable extras:
1 monitoring output – Trailing edge function
☛ with integrated selective fuse – Auto reset
☛ suitable for signal processing – Cross-short recognition
of externally powered inputs
Features – Relay output: 3 NO, – Input for reset – Housing 45 mm, made of
1 NC with non-equivalence. thermoplastic in accordance with
(Auxiliary NC for monitoring – Feedback loop UL-94-V-0, red RAL 3000
must not be used in safety – Input for emergency stop
enabling circuits!) – DIN rail mounting
or door monitoring DIN EN 50 022-35
– Long life module for application – LED’s for K1, K2, UB and Ui
with high switching frequency.
Electrical life approximate to
mechanical life.
Approvals
ÜFZ
PR
ER
BG-
T.
Front view
13 23 33 41 X3
A1 S11 S12 X1 X2
SRB-C.45-24V
UB U i
Fuse K1 K2
12
SRB-C.45 (continued) 1
K2 K2 KB
Ui UB
K1 K2
KA KB
N
For further examples
refer to page 14/15
Model specific Operating voltage 24 VDC –15%/+20%, residual ripple max. 10%
Technical data 24 VAC –15%/+10%
(refer to page 157 Frequency 50/60 Hz (for AC operating)
for general data)
Fuse (power supply) F2: T 1.0 A/250 V (internal F1: T 1.25 A/250 V)
Power consumption max. 3.4 W; 4.4 VA, plus auxiliary output L52
Switching capacity (enabling contacts) 60 VAC/VDC, 3 A ohmic (inductive with suitable suppression)
Fuse (enabling contacts) 3 A slow blowing
Switching capacity (monitoring contacts) 41/42: 24 V/2 A; L52: max. 100 mA
Fuse (monitoring contacts) 41/42: 2 A slow blowing
Application category AC 15/DC 13, DIN VDE 0660 Part 200
Pick-up delay ≤ 120 ms
Drop-out delay ≤ 20 ms
Contact material / contacts AgSnO, self cleaning, positively driven
Contact resistance max. 100 mOhm when new
Air and creeping distances DIN VDE 0110-1 (04.97), 4 kV/2
Connections Self lifting screw terminals min. 0.5 qmm, max. 2.5 qmm
Dimensions H/W/D 83 mm/45 mm/140 mm
Weight 460 g
Ambient operating temperature 0 °C ... +45 °C (derating curve available)
Mechanical life 107 switching cycles
Terminal labeling DIN EN 50 005/DIN 50 013
13
SRB-C.45 (continued)
14
SRB-C.45 (continued) 1
14 KB 14 24
KA
KA KB KA KB
N N
15
SRB-C.46
Safety relay array for emergency stop devices,
interlocking devices and others
☛ 1- or 2-channel triggering ☛ 22.5 mm housing
☛ 3 enabling outputs and ☛ Selectable extras:
1 monitoring output – Trailing edge function
☛ with electronic short circuit – Auto reset
protection "Hybrid fuse" – Cross-short recognition
☛ suitable for signal processing
of externally powered inputs
Features – Relay output: 3 NO, 1 NC – Feedback loop – Housing 22.5 mm, made of
(Auxiliary NC for monitoring thermoplastic in accordance with
must not be used in safety – Input for emergency stop UL-94-V-0, red RAL 3000
enabling circuits!) or door monitoring
– DIN rail mounting
– Input for reset – LED’s for K1, K2, Ui DIN EN 50 022
Approvals
ÜFZ
PR
ER
BG-
T.
Front view
13 23 33 41
A1 S11 X1 X3
K1
Ui
SRB-C.46 K2
A2 S12 S21 S22
14 24 34 42
16
SRB-NA-R-C.46 (continued) 1
F1
** Hybrid fuse
**
Trigger circuit
K1 KA
Ui
K2 KB
K1 K2
A2 14 24 34 42
KA KB
N
For further examples
refer to page 18/19
Model specific Operating voltage 24 VDC –15%/+20%, residual ripple max. 10%
Technical data 24 VAC –15%/+10%
(refer to page 157 Frequency 50/60 Hz (for AC operating)
for general data)
Fuse (power supply) Internal electronic fuse, triggering current > 0.6 A, reset after power
down
Power consumption max. 2.4 W; 3.3 VA
Switching capacity (enabling contacts) 230 VAC, 4 A ohmic (inductive with suitable suppression)
Fuse (enabling contacts) 4 A slow blowing
Switching capacity (monitoring contacts) 24 VDC, 2 A
Fuse (monitoring contacts) 2 A slow blowing
Application category AC 15/DC 13, DIN VDE 0660 Part 200
Pick-up delay ≤ 200 ms/≤ 30 ms (Auto start, reset button)
Drop-out delay ≤ 20 ms
Contact material / contacts AgSnO, self cleaning, positively driven
Contact resistance max. 100 mOhm when new
Air and creeping distances DIN VDE 0110-1 (04.97), 4 kV/2
Connections Self lifting screw terminals min. 0.6 qmm, max. 2.5 qmm
Dimensions H/W/D 90 mm/22.5 mm/121 mm
Weight 235 g
Ambient operating temperature –25 °C ... +45 °C (derating curve available)
Mechanical life 107 switching cycles
Terminal labeling DIN EN 50 005/DIN 50 013
17
SRB-C.46 (continued)
0 Safety category 3 or 4 1 0
1
S12 S21 X1 in accordance with S12 S22 X1
EN 954-1.
18
SRB-C.46 (continued) 1
14 KB
KB
14 1414 2424 KA
KA
KA
KA KB
KB KA KB
KA KB
NN N
N
Advice
For "Automatic Reset" S11 X1
connect feed back loop to X1-
X3 or apply jumper X1-X3 if
no feed back loop is used.
When using external reset
button (feed back loop
connected to S11-X1), unit is RESET
triggered by trailing edge
function. KA
KA
Trailing edge function with
"fail-safe" function only by a
DC power supply. KB
KB
After a performed "Emer-
gency Shut Down" an auto-
matic restart of the system
must be prevented by the
higher ranking electric
circuitry when the relay X1 X3
module SRB-C.46/e is been
set into mode "Automatic
Start" (refer to EN 60 204-1,
part 9.2.5.4.2 and part 10.8.3).
19
SRB-C.47
Safety relay array for emergency stop devices,
interlocking devices and others
☛ 1- or 2-channel triggering ☛ 22.5 mm housing
☛ 3 enabling outputs, instant and ☛ Selectable extras:
1 enabling output, drop-out delayed – Trailing edge function
☛ with "Hybrid fuse" – Auto reset
☛ suitable for processing of – Cross-short recognition
externally powered input signals
Approvals
ÜFZ
PR
ER
BG-
T.
Front view
13 23 37 X2
A1 S11 X1 X3
SRB-C.47 Ui K1
K2 K3/4
t: s
A2 S12 S21 S22
14 24 38 L42
20
SRB-C.47 (continued) 1
F1
** Hybrid fuse
**
TRIGGER CIRCUIT
K1 KA
K3
Ui
K2 KB
K1 K2 K3 K4 K4
A2 L42 14 24 38
KA KB
N
For further examples
refer to page 22/23
Model specific Operating voltage 24 VDC –15%/+20%, residual ripple max. 10%
Technical data 24 VAC –15%/+6%
(refer to page 157 Frequency 50/60 Hz (for AC operating)
for general data)
Fuse (power supply) Internal electronic fuse, triggering current < 0.6 A, reset after power
down
Power consumption max. 4 W; 5.5 VA, plus auxiliary output L42
Switching capacity (enabling contacts) 230 VAC, 4 A ohmic (inductive with suitable suppression)
Fuse (enabling contacts) 4 A slow blowing
Switching capacity (monitoring contacts) L42: 24 VDC, 100 mA
Application category AC 15/DC 13, DIN VDE 0660 Part 200
13/14, 23/24: AC 15: 250 V/1.5 A; DC 13: 24 V/1.2 A
37/38: AC 15: 250 V/3 A; DC 13: 24 V/2 A
Pick-up delay ≤ 120 ms/≤ 30 ms (Auto start, reset button)
Drop-out delay ≤ 20 ms
Contact material / contacts AgSnO, self cleaning, positively driven
Contact resistance max. 100 mOhm when new
Air and creeping distances DIN VDE 0110-1 (04.97), 4 kV/2
Connections Self lifting screw terminals min. 0.5 qmm, max. 2.5 qmm
Dimensions H/W/D 90 mm/22.5 mm/121 mm
Weight 235 g
Ambient operating temperature –25 °C ... +45 °C (derating curve available)
Mechanical life 107 switching cycles
Terminal labeling DIN EN 50 005/DIN 50 013
21
SRB-C.47 (continued)
22
SRB-NA-R-C.47 (continued) 1
14 KB 14 24 KA
KA KB KA KB
N N
Advice
For "Automatic Reset"
connect feed back loop to X1 X1
X1-X3 or apply jumper
X1-X3 if no feed back
loop is used.
When using external reset
button (feed back loop
connected to X1-X2), unit RESET
is triggered by trailing
edge function. KA
KA
Trailing edge function with
"fail-safe" function only by
a DC power supply. KB
KB
After a performed
"Emergency Shut Down"
an automatic restart of the
system must be prevented
by the higher ranking
electric circuitry when the X2 X3
relay module SRB-C.46/e
is been set into mode
"Automatic Start" (refer to
EN 60 204-1, part 9.2.5.4.2
and part 10.8.3).
23
24
SRB modules 22.5 mm wide,
STOP category 0
Options
0 .1
t. t 2
ca ca A) ) 1/ g ts
P P ( ts (A el i o n e r i n n
T O T O n t u n t r y a n n
i t g t i o inpu
S s S r r e t p r r e g o ch g n t r i g n c d
ts u
pu tpu ad c C o ad c ca w ∞ r e c n e l ge f wer t e s C
t u u te o u e t
t l al l
o u u
o lo y N l y
o e t nd o o r t
h a n e d p o
a r t VA
/ o va rov ova
g
in in
g x. ar x . s a f wi s h - c g al st C C AC AC pr pp pr
a b l a b l m a x i l i m a x . me- o s s - n g l e a i l i n t e r n i t i a l V D V A 5 V 0 V a p A a a p
u a
Type E n E n = > A = > m Ti C r S i Tr Ex I n 24 48 11 23 BG CS UL
SRB-NA-R-C.14 2 6 4 ✚ ✚ ● ● ✔ ✔ ✔ refer to page 26
SRB-NA-R-C.15 3 6 1 2 3 ✚ ✚ ● ● ✔ ✔ ✔ refer to page 30
SRB-NA-R-C.17 2 4 4 ✚ ✚ ● ●* ✔ ✔ ✔ refer to page 34
SRB-NA-R-C.18 2 6 4 ✚ ● ● ● ✔ ✔ ✔ refer to page 38
SRB-NA-R-C.36 2 6 4 ✚ ● ● ● ●* ✔ ✔ ✔ refer to page 42
✚ = fixed; ● = selectable; ● = selectable feature; * = available in 24 VDC only; ✔ = approved
25
SRB-NA-R-C.14
Safety relay array for emergency stop devices,
interlocking devices and others
☛ 2 enabling outputs
☛ Cross-short recognition
Features – Relay output: 2 NO – Input for emergency stop – Housing 22.5 mm, made of
or door monitoring thermoplastic in accordance with
– Reset, feedback loop UL-94-V-0, red RAL 3000
– LED’s for K1, K2, Ui
– DIN rail mounting
DIN EN 50 022
Approvals
ÜFZ
PR
ER
BG-
T.
Front view
C C1 23
13 S1 24
K1
SRB- UB
NA-R
-C.14 K2
X2 S2 X1
14 D1 D
26
SRB-NA-R-C.14 (continued)
Wiring diagram L1
Example for dual-channel door
monitoring using two limit switches
Open ****
(one with positive opening contacts) and
Closed
KB external reset button.
Reset
Dual-channel output, suitable for contact
KA reinforcement or contact multiplication,
using relays or contactors with positively
C C1 S1 X1 X2 13 23
guided contacts.
**** = Feedback loop
F1** Wire breakage and earth leakage in the
K2 K1 K1 K2 Monitoring circuits are detected.
K1 KA
** Fuse M 0.5 A
(an external leading fuse M 0.25 A
is recommended)
K2 KB
K1 K2
D D1 S2 14 24
KA KB
Model specific
Operating voltage 24VDC –15%/+20%, residual ripple max. 10%
Technical data
24 VAC –15%/+6%
(refer to page 157
for general data) Frequency 50/60 Hz (for AC operating)
Fuse (power supply) M 0.25 A/250 V (internal M 0.5 A/250 V)
Power consumption max. 2.5 VA
Switching capacity (enabling contacts) 230 VAC, 6 A ohmic (inductive with suitable suppression)
Fuse (enabling contacts) 6 A slow blowing
Application category AC 15/DC 13, DIN VDE 0660 Part 200
Pick-up delay ≤ 10 ms
Drop-out delay ≤ 30 ms
Contact material / contacts AgSnO, self cleaning, positively driven
Contact resistance max. 100 mOhm when new
Air and creeping distances DIN VDE 0110-1 (04.97), 4 kV/2
Connections Self lifting screw terminals min. 0.6 qmm, max. 2.5 qmm
Dimensions H/W/D 82 mm/22.5 mm/98.8 mm
Weight 190 g
Ambient operating temperature –25 °C ... +45 °C (derating curve page 157)
Mechanical life 107 switching cycles
Terminal labeling DIN EN 60 445/DIN 40 719 Part 2
27
SRB-NA-R-C.14 (continued)
S1 S2 X2 C S1 S2 X2
Wiring example:
Input level
C1 D1 X1
Dual-channel door
monitoring according to Open
EN 1088, one limit switch
Closed
with positive opening
contact.
Reset
Wire breakage and earth
leakage in the door
monitoring circuits are
detected.
Cross-shorts in the
emergency stop circuits are
detected.
With external reset button
for increased safety
requirements.
Safety category 3 or 4 S1 S2 X2
in accordance with
EN 954-1.
28
SRB-NA-R-C.14 (continued)
14 KB 14 24 KA
KA KB KA KB
N N
29
SRB-NA-R-C.15, ...-C.15/1
Safety relay array for emergency stop devices,
interlocking devices and others
☛ 3 enabling outputs and 1 monitoring output
☛ Cross-short recognition
Features – Relay output: 3 NO, 1 NC – NC contacts for monitoring – Housing 22.5 mm, made of
(Auxiliary NC for monitoring (SRB-NA-R-C.15/1: in series) thermoplastic in accordance with
must not be used in Safety (SRB-NA-R-C.15: in parallel) UL-94-V-0, red RAL 3000
Enabling Circuits!)
– Input for emergency stop – DIN rail mounting
– Reset, feedback loop or door monitoring DIN EN 50 022
– LED’s for K1, K2, Ui
Approvals
(SRB-NA-R-C.15) PR
ÜFZ
ER
BG-
T.
Front view
13 23 33
14 24 34
K2
UB SRB-
NA-R
K1 -C.15
41 X1 C
42 X2 D
30
SRB-NA-R-C.15, ...-C.15/1 (continued)
Model specific Operating voltage 24 VDC –15%/+20%, residual ripple max. 10%
Technical data 24 VAC –15%/+6%
(refer to page 157 Frequency 50/60 Hz (for AC operating)
for general data)
Fuse (power supply) M 0.25 A/250 V (internal M 0.5 A/250 V)
Power consumption max. 2.5 VA
Switching capacity (enabling contacts) 230 VAC, 6 A ohmic (inductive with suitable suppression)
Fuse (enabling contacts) 6 A slow blowing
Switching capacity (monitoring contacts) 24 V, 2 A ohmic (inductive with suitable suppression)
Fuse (monitoring contacts) 2 A slow blowing
Application category AC 15/DC 13, DIN VDE 0660 Part 200
Pick-up delay ≤ 10 ms
Drop-out delay ≤ 30 ms
Contact material / contacts AgSnO, self cleaning, positively driven
Contact resistance max. 100 mOhm when new
Air and creeping distances DIN VDE 0110-1 (04.97), 4 kV/2
Connections Self lifting screw terminals min. 0.6 qmm, max. 2.5 qmm
Dimensions H/W/D 82 mm/22.5 mm/98.8 mm
Weight 190 g
Ambient operating temperature –25 °C ... +45 °C (derating curve page 157)
Mechanical life 107 switching cycles
Terminal labeling DIN EN 60 445/DIN 40 719 Part 2
31
SRB-NA-R-C.15, ...-C.15/1 (continued)
C D X2 C D X2
32
SRB-NA-R-C.15, ...-C.15/1 (continued)
14 KB 14 24
KA
KA KB KA KB
N N
33
SRB-NA-R-C.17
Safety relay array for emergency stop devices,
interlocking devices and others
☛ 2 enabling outputs
☛ Selectable extras:
– Trailing edge function
– Auto reset
☛ Cross-short recognition
Approvals
ÜFZ
PR
ER
BG-
T.
Front view
13 23 X1
14 24 X2
K1
SRB-
NA-R
-C.17 K2
S1 S2 C
S11 S21 D
34
SRB-NA-R-C.17 (continued)
Wiring diagram L1
Example for dual-channel door
monitoring using two limit switches
Open
Closed **** (one with positive opening contacts) and
KB external reset button.
Reset
Dual-channel output, suitable for contact
KA reinforcement or contact multiplication,
using relays or contactors with positively
C S2 S1 S11 S21 X1 X2 13 23
guided contacts.
**** = Feedback loop
K2 KB
K1 K2
D 14 24
KA KB
Model specific Operating voltage 24 VDC –15%/+20%, residual ripple max. 10%
Technical data
Fuse (power supply) internal electronic fuse, breaking current > 0.6 A, reset time approx. 1 sec.
(refer to page 157
for general data) Power consumption max. 2.5 W
Switching capacity (enabling contacts) 230 VAC, 4 A ohmic (inductive with suitable suppression)
Fuse (enabling contacts) 4 A slow blowing
Application category AC 15/DC 13, DIN VDE 0660 Part 200
Pick-up delay ≤ 50 ms
Drop-out delay ≤ 20 ms
Contact material / contacts AgSnO, self cleaning, positively driven
Contact resistance max. 100 mOhm when new
Air and creeping distances DIN VDE 0110-1 (04.97), 4 kV/2
Connections Self lifting screw terminals min. 0.6 qmm, max. 2.5 qmm
Dimensions H/W/D 82 mm/22.5 mm/98.8 mm
Weight 190 g
Ambient operating temperature 0 °C ... +45 °C (derating curve page 157)
Mechanical life 107 switching cycles
Terminal labeling DIN EN 60 445/DIN 40 719 Part 2
35
SRB-NA-R-C.17 (continued)
Advice:
Change over from mode
"External reset with
trailing edge" to mode A1 (+) A2 (-) A1 (+) A2 (-)
"Automatic reset" is
achieved by altering the
polarity of the supply
voltage.
In "Automatic reset" the
reset button is eliminated.
C D D C
36
SRB-NA-R-C.17 (continued)
14 KB 14 24 KA
KA KB KA KB
N N
37
SRB-NA-R-C.18
Safety relay array for emergency stop devices,
interlocking devices and others
☛ 2 enabling outputs
☛ Suitable for semiconductor monitoring outputs
Features – Relay output: 2 NO – Input for emergency stop – Housing 22.5 mm, made of
or door monitoring thermoplastic in accordance with
– Reset, feedback loop UL-94-V-0, red RAL 3000
– LED’s for K1, K2, UB
– No cross-short recognition – DIN rail mounting
DIN EN 50 022
Approvals
ÜFZ
PR
ER
BG-
T.
Front view
C C1 23
13 S1 24
K1
SRB- UB
NA-R
-C.18 K2
X2 S2 X1
14 C1.1 D
38
SRB-NA-R-C.18 (continued)
Wiring diagram L1
Example for dual-channel door
Open
****
Reset
monitoring using two limit switches
Closed
(one with positive opening contacts) and
KB external reset button.
Dual-channel output, suitable for contact
KA reinforcement or contact multiplication,
using relays or contactors with positively
C C1.1 C1 S1 X1 X2 S2 13 23
guided contacts.
**** = Feedback loop
F1** Wire breakage and earth leakage in the
K2 K1 K2
K1 monitoring circuits are detected.
K1 KA
** Fuse M 0.5 A
(an external leading fuse M 0.25 A
is recommended)
K2 KB
K1 K2
D 14 24
KA KB
Model specific Operating voltage 24 VDC –15%/+20%, residual ripple max. 10%
Technical data 24 VAC –15%/+6%
(refer to page 157 Frequency 50/60 Hz (for AC operating)
for general data)
Fuse (power supply) M 0.25 A/250 V (internal M 0.5 A/250 V)
Power consumtion max. 2.5 VA
Switching capacity (enabling contacts) 230 VAC, 6 A ohmic (inductive with suitable suppression)
Fuse (enabling contacts) 6 A slow blowing
Application category AC 15/DC 13, DIN VDE 0660 Part 200
Pick-up delay ≤ 10 ms
Drop-out delay ≤ 30 ms
Contact material / contacts AgSnO, self cleaning, positively driven
Contact resistance max. 100 mOhm when new
Air and creeping distances DIN VDE 0110-1 (04.97), 4 kV/2
Connections Self lifting screw terminals min. 0.6 qmm, max. 2.5 qmm
Dimensions H/W/D 82 mm/22.5 mm/98.8 mm
Weight 190 g
Ambient operating temperature –25 °C ... +45 °C (derating curve page 157)
Mechanical life 107 switching cycles
Terminal labeling DIN EN 60 445/DIN 40 719 Part 2
39
SRB-NA-R-C.18 (continued)
S1 S2 X2 C S1 S2 X2
40
SRB-NA-R-C.18 (continued)
14 KB 14 24
KA
KA KB KA KB
N N
41
SRB-NA-R-C.36
Safety relay array for emergency stop devices,
interlocking devices and others
☛ 2 enabling outputs
☛ Selectable extras:
– Trailing edge function
– Auto reset
☛ Suitable for semiconductor monitoring outputs
Features – Relay output: 2 NO – Input for emergency stop – Housing 22.5 mm, made of
or door monitoring thermoplastic in accordance with
– Reset, feedback loop UL-94-V-0, red RAL 3000
– LED’s for K1, K2
– No cross-short recognition – DIN rail mounting
DIN EN 50 022
Approvals
ÜFZ
PR
ER
BG-
T.
Front view
13 23 X1
14 24 X2
K2
SRB-
NA-R-
K1 C.36
S1 S2 C
C1 X3 D
42
SRB-NA-R-C.36 (continued)
Wiring diagram L1
Example for dual-channel door
monitoring using two limit switches
Open
Closed
**** (one with positive opening contacts) and
external reset button.
KB
Reset Dual-channel output, suitable for contact
KA reinforcement or contact multiplication,
using relays or contactors with positively
C C1 S1 S2 X1 X2 X3 13 23
guided contacts.
**** = Feedback loop
F1
**
Wire breakage and earth leakage in the
K1 K2 monitoring circuits are detected.
K1
KA ** Internal electronic fuse
Trigger circuit
K2
K1 K2 KB
D 14 24
KA KB
Model specific Operating voltage 24 VDC –15%/+20%, residual ripple max. 10%
Technical data
Fuse (power supply) internal electronic fuse, breaking current > 0.6 A, reset time approx. 1 sec.
(refer to page 157
for general data) Power consumption max. 2.5 W
Switching capacity (enabling contacts) 230 VAC, 6 A ohmic (inductive with suitable suppression)
Fuse (enabling contacts) 6 A slow blowing
Application category AC 15/DC 13, DIN VDE 0660 Part 200
Pick-up delay ≤ 330 ms/720 ms (Reset /Auto Reset)
Drop-out delay ≤ 20 ms
Contact material / contacts AgSnO, self cleaning, positively driven
Contact resistance max. 100 mOhm when new
Air and creeping distances DIN VDE 0110-1 (04.97), 4 kV/2
Connections Self lifting screw terminals min. 0.6 qmm, max. 2.5 qmm
Dimensions H/W/D 82 mm/22.5 mm/98.8 mm
Weight 190 g
Ambient operating temperature 0 °C ... +45 °C (derating curve page 157)
Mechanical life 107 switching cycles
Terminal labeling DIN EN 60 445/DIN 40 719 Part 2
43
SRB-NA-R-C.36 (continued)
S1 S2 X2 S1 S2 X2
S1 S2 X2 Safety category 3 or 4
S1 S2 X2
in accordance with
EN 954-1.
S1 S2 X2 X2 X3
44
SRB-NA-R-C.36 (continued)
14 KB 14 24 KA
KA KB KA KB
N N
45
46
SRB modules 22.5 wide,
STOP category 1
3
☛ Enabling outputs drop-out delayed: 1 sec.
☛ 3 enabling outputs and 1 monitoring output
☛ max. load current: 6 Ampere
☛ max. safety category: 4
☛ 1- or 2-channel triggering
☛ Cross-short recognition
☛ 24 VDC/VAC-Version
☛ Approvals: BG, CSA, UL
Options
0 . 1*
t. t /2
ca ca A) A ) e l1 n ng ts
P P
T O TO nt ( uts nt ( ry a nn itio geri ion npu
S S r e p r e o c h n i g c t i
s s ur out ur teg ∞ g r un red
ut ut co l t t
u tp utp ad c C ad c y ca ow t re nne ge f owe t tes AC l
al ova val
o o l o y N l o et nd or ha ed p ar / V o v r
g
in in
g x. ar x. af wi sh -c g al st C C AC AC pr pp pro
a bl abl ma xili ma x. s me oss- ngle ailin tern itial VD VA 5 V 0 V ap A a ap
u a
Type En En => A => m Ti C r Si Tr Ex In 24 48 11 23 BG CS UL
SRB-NA-R-C.16 3 6 1 2 3 ✚ ✚ ● ● ✔ ✔ ✔ refer to page 48
* = drop-out delay: 1 sec.; ✚ = fixed; ● = selectable; ✔ = approved
47
47
SRB-NA-R-C.16, ...-C.16/1
Safety relay array for emergency stop devices,
interlocking devices and others
☛ 3 enabling outputs and 1 monitoring output
☛ Drop-out delayed (1 sec.) enabling outputs
☛ STOP category 1
☛ Cross-short recognition
Features – Relay output: 3 NO, 1NC – NC contacts for monitoring – LED’s for K1, K2, UB
(Auxiliary NC for monitoring (SRB-NA-R-C.16/1: in series)
must not be used in safety (SRB-NA-R-C.16: in parallel) – Housing 22.5 mm, made of
enabling circuits!) thermoplastic in accordance with
– Input for emergency stop UL-94-V-0, red RAL 3000
– Reset, feedback loop or door monitoring
– DIN rail mounting
DIN EN 50 022
Approvals
ÜFZ
PR
ER
BG-
T.
Front view
13 23 33
14 24 34
K2
UB SRB-
NA-R
K1 -C.16
41 X1 C
42 X2 D
48
SRB-NA-R-C.16, ...-C.16/1 (continued)
Model specific Operating voltage 24 VDC –15%/+20%, residual ripple max. 10%
Technical data 24 VAC –15%/+6%
(refer to page 157 Frequency 50/60 Hz (for AC operating)
for general data)
Fuse (power supply) M 0.5 A/250 V
Power consumption max. 2.5 VA
Switching capacity (enabling contacts) 230 VAC, 6 A ohmic (inductive with suitable suppression)
Fuse (enabling contacts) 6 A slow blowing
Switching capacity (monitoring contacts) 24 V, 2 A ohmic (inductive with suitable suppression)
Fuse (monitoring contacts) 2 A slow blowing
Application category AC 15/DC 13, DIN VDE 0660 Part 200
Pick-up delay ≤ 50 ms
Drop-out delay 1.1 s –20%/+20% (for UB = 24 VDC)
Contact material / contacts AgSnO, self cleaning, positively driven
Contact resistance max. 100 mOhm when new
Air and creeping distances DIN VDE 0110-1 (04.97), 4 kV/2
Connections Self lifting screw terminals min. 0.6 qmm, max. 2.5 qmm
Dimensions H/W/D 82 mm/22.5 mm/98.8 mm
Weight 190 g
Ambient operating temperature –25 °C ... +45 °C (derating curve page 157)
Mechanical life 107 switching cycles
Terminal labeling DIN EN 60 445/DIN 40 719 Part 2
49
SRB-NA-R-C.16, ...-C.16/1 (continued)
C D X2 C D X2
50
SRB-NA-R-C.16, ...-C.16/1 (continued)
KA KB KA KB
N N
51
52
SRB modules 45 mm wide,
standard version,
STOP category 0
Options
0 .1
t. t /2
ca ca A) uts A) l1 n g
OP P
O nt ( utp nt ( ry n n io erin on puts
e
a t
S T S T e o e o h n i g g cti in
u ts uts curr /NO curr teg ∞ c cog l tri fun red t
tp tp d C d ca w re ne e we tes C l al l
ou g ou loa y N loa ety ndo ort han edg l po art /VA C C o va rov ova
g . r . a f i h c g a s t C C A r p p pr
in in x a x w s - A p
a bl abl ma xili ma x. s me oss- ngle ailin tern itial VD VA 5 V 0 V ap A a ap
u a L
Type En En => A => m Ti Cr Si Tr Ex In 24 48 11 23 BG CS U
SRB-NA-R-C.12 3 6 3 ✚ ✚ ● ● ✚ ✚ ✚ ✔ ✔ ✔ refer to page 54
SRB-NA-R-C.33 3 6 1 2 4 ✚ ● ● ● ✚ ✚ ✚ ✔ ✔ ✔ refer to page 58
SRB-NA-R-C.34 3 6 1/1 2 4 ✚ ● ● ● ● ✔ ✔ ✔ refer to page 62
✚ = fixed; ● = selectable; ● = selectable feature; ✔ = approved; ✔ = in preparation
53
SRB-NA-R-C.12
Safety relay array for emergency stop devices,
interlocking devices and others
☛ 3 enabling outputs
☛ 3-channel triggering
☛ Different operating voltage
☛ Cross-short recognition
Features – Relay output: 3 NO – LED’s for K1, K2, UB – DIN rail mounting
DIN EN 50 022
– Reset, feedback loop – Housing 45 mm, made of
thermoplastic in accordance with
– Input for emergency stop UL-94-V-0, red RAL 3000
or door monitoring
Approvals
ÜFZ
PR
ER
BG-
T.
Front view
C S1.1 13 23 33
K1
UB
K2
SRB-NA-
R-C.12
D S2.1 14 24 34
54
SRB-NA-R-C.12 (continued)
KA KB
Model specific Operating voltage 24 VDC –15%/+20%, residual ripple max. 10%
Technical data 48 VAC, 115 VAC, 230 VAC –15%/+6%
(refer to page 157 Frequency 50/60 Hz (for AC operating)
for general data)
Fuse (power supply) M 0.25 A/250 V (internal M 0.5 A/250 V)
Power consumption max. 2.5 VA
Switching capacity (enabling contacts) 230 VAC, 6 A ohmic (inductive with suitable suppression)
Fuse (enabling contacts) 6 A slow blowing
Application category AC 15/DC 13, DIN VDE 0660 Part 200
Pick-up delay ≤ 30 ms
Drop-out delay ≤ 50 ms
Contact material / contacts AgSnO, self cleaning, positively driven
Contact resistance max. 100 mOhm when new
Air and creeping distances DIN VDE 0110-1 (04.97), 4 kV/2
Connections Self lifting screw terminals min. 0.6 qmm, max. 2.5 qmm
Dimensions H/W/D 83 mm/45 mm/127 mm
Weight 280 g (360 g at 48 VAC, 115 VAC and 230 VAC versions)
Ambient operating temperature –25 °C ... +45 °C (derating curve page 157)
Mechanical life 107 switching cycles
Terminal labeling DIN EN 60 445/DIN 40 719 Part 2
55
SRB-NA-R-C.12 (continued)
56
SRB-NA-R-C.12 (continued)
14 KB 14 24 KA
KA KB KA KB
N N
57
SRB-NA-R-C.33
Safety relay array for emergency stop devices,
interlocking devices and others
☛ 2 enabling outputs and 1 monitoring output
☛ Different operating voltage
Features – Relay output: 3 NO, 1 NC – Input for emergency stop – DIN rail mounting
(Auxiliary NC for monitoring or door monitoring DIN EN 50 022
must not be used in safety
enabling circuits!) – LED’s for K1, K2, UB, UI
Approvals
ÜFZ
PR
ER
BG-
T.
Front view
41 33 23 13 A1
T11 T12 T12 T22
SRB-NA-R-
C.33 UB U i
Fuse K1 K2
T33 T34 PE X1 X2
42 34 24 14 A2
58
SRB-NA-R-C.33 (continued)
Wiring diagram L1
Example for dual-channel door
monitoring using two limit switches
OPEN
(one with positive opening contacts) and
CLOSED
KB external reset button.
**** Reset
Dual-channel output, suitable for contact
KA reinforcement or contact multiplication,
K1 K2
K2 KB
A2 PE 14 24 34 42
KA KB
N
For further examples
refer to page 60/61
Model specific Operating voltage 24 VDC –15%/+20%, residual ripple max. 10%
Technical data 24 VAC, 48 VAC, 115 VAC, 230 VAC –15%/+6%
(refer to page 157 Frequency 50/60 Hz (for AC operating)
for general data)
Fuse (power supply) F2: T 0.125 A/250 V (internal F1: TM 0.25 A/250 V)
Power consumption max. 2.5 VA
Switching capacity (enabling contacts) 230 VAC, 6 A ohmic (inductive with suitable suppression)
Fuse (enabling contacts) 6 A slow blowing
Switching capacity (monitoring contacts) 24 V, 2 A ohmic (inductive with suitable suppression)
Fuse (monitoring contacts) 2 A slow blowing
Application category AC 15/DC 13, DIN VDE 0660 Part 200
Pick-up delay ≤ 20 ms
Drop-out delay ≤ 50 ms
Contact material / contacts AgSnO, self cleaning, positively driven
Contact resistance max. 100 mOhm when new
Air and creeping distances DIN VDE 0110-1 (04.97), 4 kV/2
Connections Self lifting screw terminals min. 0.5 qmm, max. 2.5 qmm
Dimensions H/B/T 83 mm/45 mm/140 mm
Weight 190 g (280 g at 48 VAC, 115 VAC and 230 VAC versions)
Ambient operating temperature –25 °C ... +45 °C (derating curve page 157)
Mechanical life 107 switching cycles
Terminal labeling DIN EN 50 005/DIN 50 013
59
SRB-NA-R-C.33 (continued)
60
SRB-NA-R-C.33 (continued)
KA KB
KA KB
N N
61
SRB-NA-R-C.34
Safety relay array for emergency stop devices,
interlocking devices and others
☛ 3 enabling outputs and 2 monitoring outputs
☛ Selectable extras:
– Trailing edge function
– Auto reset
Features – Relay output: 3 NO, 2 NO/NC – Input for emergency stop – DIN rail mounting
(Auxiliary NO/NC for monitoring or door monitoring DIN EN 50 022
must not be used in safety
enabling circuits!) – LED’s for K1, K2, UB, UI
Approvals
ÜFZ
PR
ER
BG-
T.
Front view
13 23 33 41 53
A1 T11 T12 T22 X5
SRB-NA-R-
C.34-24V UB U i
Fuse K2 K3
T33 T34 X3 X4 A2
14 24 34 42 54
62
SRB-NA-R-C.34 (continued)
K3 KB
K1 K2 K2A K3 K3A K3A
A2 14 24 34 42 54
KA KB
N
For further examples
refer to page 64/65
Model specific Operating voltage 24 VDC –15%/+20%, residual ripple max. 10%
Technical data 24 VAC –15%/+6%
(refer to page 157 Frequency 50/60 Hz (for AC operating)
for general data)
Fuse (power supply) F2: T 0.25 A/250 V (internal F1: T 0.5 A/250 V)
Power consumption max. 4 W; 4.3 VA
Switching capacity (enabling contacts) 230 VAC, 6 A ohmic (inductive with suitable suppression)
DC 13: 24 V/2 A; AC 15: 230 VAC/3 A
Fuse (enabling contacts) 6 A slow blowing
Switching capacity (monitoring contacts) max. 24 VDC/2 A ohmic (inductive with suitable suppression)
Fuse (monitoring contacts) 2 A slow blowing
Application category AC 15/DC 13, DIN VDE 0660 Part 200
Pick-up delay ≤ 20 ms
Drop-out delay ≤ 30 ms
Contact material / contacts AgCdO, self cleaning, positively driven
Contact resistance max. 100 mOhm when new
Air and creeping distances DIN VDE 0110-1 (04.97), 4 kV/2
Connections Self lifting screw terminals min. 0.5 qmm, max. 2.5 qmm
Dimensions H/W/D 83 mm/45 mm/140 mm
Weight 200 g
Ambient operating temperature –25 °C ... +45 °C (derating curve page 157)
Mechanical life 107 switching cycles
Terminal labeling DIN EN 50 005/DIN 50 013
63
SRB-NA-R-C.34 (continued)
T 34 X4 T 34 X5 X4
64
SRB-NA-R-C.34 (continued)
KA KB KA KB
N N
65
66
SRB modules 45 mm wide,
standard versions,
STOP category 1
Options
0 1* 2
a t. at. 1/
c c A) A ) el on ring n
P P ( ( n
O O t ts t n ti e o ts
s ST s ST rren tpu rren gory cha gni rigg ncti inpu
t
pu pu
t cu ou cu te ∞ eco el t fu er st C
a
ut out oad NC oad ty c dow rt r ann dge pow rt te VA l al l
o l ry . l fe in ho ch e a / C C o va rov ova
g g . a g a l s t C C A r p p pr
in in x a x w s - A p
a bl abl ma xili ma x. s me oss- ngle ailin tern itial VD VA 5 V 0 V ap A a ap
a
Type En En => Au => m Ti Cr Si Tr Ex In 24 48 11 23 BG CS UL
SRB-NA-R-C.35/WE 3 1 6 1 2 4 ● ● ● ● ✔ ✔ ✔ refer to page 68
SRB-NA-R-C.35/KE 3 1 6 1 2 4 ● ● ● ● ✔ ✔ ✔ refer to page 68
SRB-NA-R-C.35/
WE.QS 3 1 6 1 2 4 ✚ ● ● ● ✔ ✔ ✔ refer to page 68
SRB-NA-R-C.35/
KE.QS 3 1 6 1 2 4 ✚ ● ● ● ✔ ✔ ✔ refer to page 68
* = drop-out delay: 0 ... 30 sec.: setting by manufacturer (WE)/setting by customer (KE);
✚ = fixed; ● = selectable; ● = selectable feature; ✔ = in preparation
67
SRB-NA-R-C.35
Safety relay array for emergency stop devices,
interlocking devices and others
☛ 4 enabling outputs and 1 monitoring output
☛ 1 enabling output drop-out delayed: 0 ... 30 seconds
☛ Selectable extras:
– Trailing edge function
– Auto reset
Features – Relay output: 4 NO, 1 NC – Reset, feedback loop – Housing 45 mm, made of
1 NO drop out delayed thermoplastic in accordance with
(Auxiliary NC for monitoring – Input for emergency stop UL-94-V-0, red RAL 3000
must not be used in safety or door monitoring
enabling circuits!) – DIN rail mounting
– LED’s for K2, K3, K4, K5, UB, Ui DIN EN 50 022
Approvals
ÜFZ
PR
ER
BG-
T.
Front view
13 23 33 47 51
A1 T11 T12 T22 X5
SRB-NA-R-
C.35 t ...... s
UB U i
Fuse K2 K3
K4 K5
A2 A2.1 T33 T34 UT
14 24 34 48 52
68
SRB-NA-R-C.35 (continued)
K1 K2 K3 K4 K5
K4
K5
K4
KB
5
A2 A2.1 14 24 34 48 52
KA KB
Model specific Operating voltage 24 VDC –15%/+20%, residual ripple max. 10%
Technical data 24 VAC –15%/+6%
(refer to page 157 Frequency 50/60 Hz (for AC operating)
for general data)
Fuse (power supply) F2: T 0.25 A/250 V (internal F1: T 0.5 A/250 V)
Power consumption max. 3.5 W; 4.7 VA
Switching capacity (enabling contacts) 230 VAC, 6 A ohmic (inductive with suitable suppression)
DC 13: 24 V/2 A; AC 15: 230 VAC/3 A
Fuse (enabling contacts) 6 A slow blowing
Switching capacity (monitoring contacts) max. 24 V/2 A ohmic (inductive with suitable suppression)
Fuse (monitoring contacts) 2 A slow blowing
Application category AC 15/DC 13, DIN VDE 0660 Part 200
Pick-up delay ≤ 200 ms
Drop-out delay ≤ 30 ms
Contact material / contacts AgCdO self cleaning, positively driven
Contact resistance max. 100 mOhm when new
Air and creeping distances DIN VDE 0110-1 (04.97), 4 kV/2
Connections Self lifting screw terminals min. 0.5 qmm, max. 2.5 qmm
Dimensions H/W/D 83 mm/45 mm/140 mm
Weight 280 g
Ambient operating temperature –25 °C ... +45 °C (derating curve page 157)
Mechanical life 107 switching cycles
Terminal labeling DIN EN 50 005/DIN 50 013
69
SRB-NA-R-C.35 (continued)
70
SRB-NA-R-C.35 (continued)
14 48 KA 14 24 48 KA
KA KB KC KA KB KC
N N
5
* Reset button wired in * Reset button wired in
series to feedback loop. series to feedback loop.
UT T34 X5
Advice:
Drop-out delay of the 47
enabling output 47/48
adjustable 0 ... 30 sec.
Enabling output 47/48
corresponds to Stop-
category 1 in accordance
with EN 60 204-1.
Enabling output 13/14,
23/24 and 33/34
corresponds to Stop-
category 0 in accordance
with EN 60 204-1.
48
71
72
SRB modules 45 mm wide,
multifunctional version,
STOP category 0
Options
0 .1 2
t. t 1/
ca ca A) uts A) el on ring n s
P P ( t p ( n ut
S TO STO ent ou ent ory han niti igge ctio inp
s s urr NO ur
r c
teg ∞ co l t
g r un red
ut ut t
u tp utp ad c C/ ad c y ca ow t re nne ge f owe t tes AC al
l
va al
o o o
l ry N l o t d r a d
e in ho ch g e al p sta C/V C r ov pro rov
g g . . f C C r
A pp ap pp
lin lin ax lia ax sa w s-s e- in n l D A A
n ab nab > m uxi > m ax. ime ros ingl rail xter itia 4 V 8 V 15 V 30 V G a SA L a
Type E E = A = m T C S T E I n 2 4 1 2 B C U
SRB-NA-R-C.20 5 4 1 0,5 4 ✚ ● ● ● ✔ ✔ ✔ refer to page 74
SRB-NA-R-C.22 3 4 1 0,5 4 ✚ ● ● ● ✔ ✔ ✔ refer to page 78
SRB-NA-R-C.27 3 6 1/2 2/0,1 4 ✚ ● ● ● ● ● ✔ ✔ ✔ refer to page 82
✚ = fixed; = DIP switch setting; ● = selectable; ● = selectable feature; ✔ = approved; ✔ = in preparation
73
SRB-NA-R-C.20
Safety relay array for emergency stop devices,
interlocking devices and others
☛ 5 enabling outputs and 1 monitoring output
☛ Selectable extras:
– Trailing edge function
– Auto reset
– Cross-short recognition
Features – Relay output: 5 NO, 1 NC – Input for emergency stop – DIN rail mounting
(Auxiliary NC for monitoring or door monitoring DIN EN 50 022
must not be used in safety
enabling circuits!) – LED’s for K1, K2, K3, K4, UB, Ui
Approvals
ÜFZ
PR
ER
BG-
T.
Front view
13 23 33 43 53
C C1 S1 X1 X2
SRB-NA-R-
C.20-24V UB U i
Fuse K1 K3
K2 K4
D D1 S2 X2.1 L62
14 24 34 44 54
74
SRB-NA-R-C.20 (continued)
D D1 L62 14 24 34 44 54
KA KB
For further examples
N
refer to page 76/77
6
Model specific Operating voltage 24 VDC –15%/+20%, residual ripple max. 10%
Technical Data 24 VAC –15%/+6%
(Refer to page 157 Frequency 50/60 Hz (for AC operating)
for general data)
Fuse (power supply) T 1.0 A/250 V (internal T 1.25 A/250 V)
Power consumption max. 3.6 VA, plus monitoring output L62
Switching capacity (enabling contacts) 230 VAC, 4 A ohmic (inductive with suitable suppression)
NO 43/44, 53/54: DC 13: 24 VDC/2 A; AC 15: 230 VAC/3 A
Fuse (enabling contacts) 4 A slow blowing
Switching capacity (monitoring contacts) L62: max. 500 mA
Application category AC 15/DC 13, DIN VDE 0660 Part 200
Pick-up delay ≤ 30 ms
Drop-out delay ≤ 60 ms
Contact material / contacts AgSnO, AgNi self cleaning, positively driven
Contact resistance max. 100 mOhm when new
Air and creeping distances DIN VDE 0110-1 (04.97), 4 kV/2
Connections Self lifting screw terminals min. 0.5 qmm, max. 2.5 qmm
Dimensions H/W/D 83 mm/45 mm/140 mm
Weight 460 g
Ambient operating temperature –25 °C ... +45 °C (derating curve page 157)
Mechanical life 107 switching cycles
Terminal labeling DIN EN 60 445/DIN 40 719 Part 2
75
SRB-NA-R-C.20 (continued)
S1 S2 X2 S1 S2 X2
leakage in the emergency stop Emergency Reset Wire breakage and earth Reset
circuits are detected. switch off leakage in the door
Cross-shorts in the emergency monitoring circuits are
stop circuits are detected. detected.
76
SRB-NA-R-C.20 (continued)
Advice:
For "Automatic Reset" X1
apply jumper X1-X2.
When using external Reset
button (connect to X1-
X2.1), unit is triggered by
trailing edge function. Reset
Reset button wired in
series to feedback loop.
X2.1
14
14 KB 14
14 24
24
KB KA
KA
KA
KA KB
KB KA KB
KA KB
N
N N
N
77
SRB-NA-R-C.22
Safety relay array for emergency stop devices,
interlocking devices and others
☛ 3 enabling outputs and 1 monitoring output
☛ Selectable extras:
– Trailing edge function
– Auto reset
– Cross-short recognition
Features – Relay output: 3 NO, 1 NC – Input for emergency stop – DIN rail mounting
(Auxiliary NC for monitoring or door monitoring DIN EN 50 022
must not be used in safety
enabling circuits!) – LED’s for K1, K2, UB, Ui
Approvals
ÜFZ
PR
ER
BG-
T.
Front view
13 23 33
C C1 S1 X1 X2
SRB-NA-R-
C.22-24V UB U i
Fuse K1
K2
D D1 S2 X2.1 L62
14 24 34
78
SRB-NA-R-C.22 (continued)
Wiring diagram L1
Example for dual-channel door
monitoring using two limit switches
Open
**** (one with positive opening contacts) and
Closed
KB external reset button.
Reset
Dual-channel output, suitable for contact
KA reinforcement or contact multiplication,
using relays or contactors with positively
C C1 X2 X2.1 S1 X1 S2 13 23 33
guided contacts.
**** = Feedback loop
F2 K1 K2 Wire breakage and earth leakage in the
* Trigger K1 monitoring circuits are detected.
F1 circuit K1 KA
* Fuse F2 (front cover) 1 A, Fuse F1
(internal) 1.25 A
K2
K2 KB
K1 K2
D D1 L62 14 24 34
KA KB
For further examples
refer to page 80/81 N
6
Model specific Operating voltage 24 VDC –15%/+20%, residual ripple max. 10%
Technical data 24 VAC –15%/+6%
(refer to page 157 Frequency 50/60 Hz (for AC operating)
for general data)
Fuse (power supply) T 1.0 A/250 V (internal T 1.25 A/250 V)
Power consumption max. 2.0 VA, plus monitoring output L62
Switching capacity (enabling contacts) 230 VAC, 4 A ohmic (inductive with suitable suppression)
NO 43/44, 53/54: DC 13: 24 VDC/2 A; AC 15: 230 VAC/3 A
Fuse (enabling contacts) 4 A slow blowing
Switching capacity (monitoring contacts) L62: max. 500 mA
Application category AC 15/DC 13, DIN VDE 0660 Part 200
Pick-up delay ≤ 30 ms
Drop-out delay ≤ 60 ms
Contact material / contacts AgSnO, AgNi self cleaning, positively driven
Contact resistance max. 100 mOhm when new
Air and creeping distances DIN VDE 0110-1 (04.97), 4 kV/2
Connections Self lifting screw terminals min. 0.5 qmm, max. 2.5 qmm
Dimensions H/W/D 83 mm/45 mm/140 mm
Weight 460 g
Ambient operating temperature –25 °C ... +45 °C (derating curve page 157)
Mechanical life 107 switching cycles
Terminal labeling DIN EN 60 445/DIN 40 719 Part 2
79
SRB-NA-R-C.22 (continued)
S1 S2 X2 S1 S2 X2
leakage in the emergency stop Emergency Reset Wire breakage and earth Reset
circuits are detected. switch off leakage in the door
Cross-shorts in the emergency monitoring circuits are
stop circuits are detected. detected.
80
SRB-NA-R-C.22 (continued)
Advice:
For "Automatic reset" X1
apply jumper X1-X2.
When using external
reset button (connect to
X1-X2.1), unit is triggered
by trailing edge function. Reset
Reset button wired in
series to feedback loop.
X2.1
14 KB 14 24
KA
KA KB KA KB
N N
81
SRB-NA-R-C.27
Safety relay array for emergency stop devices,
interlocking devices and others
☛ 3 enabling outputs and 1 monitoring output
☛ 2 semiconductor outputs
☛ Selectable extras:
– Auto reset
– Trailing edge function
– Initial start test
Features – Relay output: 3 NO, 1 NC – Reset, feedback loop – Housing 45 mm, made of
(Auxiliary NC for monitoring thermoplastic in accordance with
must not be used in safety – Input for emergency stop UL-94-V-0, red RAL 3000
enabling circuits!) or door monitoring
– DIN rail mounting
– Monitoring outputs for K1, – LED’s for K1, K2, K3, Qs, UB, Ui DIN EN 50 022
K2/K3
Approvals
ÜFZ
PR
ER
BG-
T.
Front view
41 13 23 33 L11
C C1 S11 S12 L13
SRB-NA-R-
C.27-24V UB U i
Fuse K1 K3
K2 Qs
D S13 S21 S41 L14
42 14 24 34 D2
82
SRB-NA-R-C.27 (continued)
F2 S5
**** = Feedback loop
K1
F1
S1 K2 K1 K1 K2 K1 K3
Wire breakage and earth leakage in the
monitoring circuits are detected.
K1 K2 KA
Cross-short
recognition
K3 K2 K3 S4
K3 KB
K1 K2 K3
KA KB
83
SRB-NA-R-C.27 (continued)
84
SRB-NA-R-C.27 (continued)
14 KB 14 24 KA
KA KB KA KB
N N
Advice: Advice:
6
For "Automatic reset" apply C1 Semiconductor outputs 24 VDC 0V
jumper C1-S13. L11 and L14 are
When using external reset galvanically separated
button (switch S1 is set to from the other sections of
"1"), unit is triggered by the SRB-NA-R-C.27.
trailing edge function. Reset Provide power supply
If the time difference between through inputs L13 and
input channel 1 and 2 of the D2.
safety relay exceeds ca. Semiconductor output L11
100 msec. when connecting a is linked to relay K1
safety limit switch or (reset), semiconductor
interlocking device, a self- output L14 is linked to
locking function can be relays K2 and K3.
achieved by setting switch S5
to "1". The time difference is
then extended to infinite.
S13 L13 D2
Rear view
Setting:
S1 ON = Trailing edge function on OFF = Trailing edge function off
1 0 S5
S4 ON = Cross-short recognition off OFF = Cross-short recognition on
1 0 S4 S5 ON = Time delay between input OFF = Time delay between input
1 0 S1
channel 1 and 2 infinite channel 1 and 2 ca. 100 msec.
85
86
SRB modules 45 mm wide,
multifunctional version,
STOP category 1
7
Options
0 . 1* 2
t. t 1/
ca ca A) ) el on ring n s
P P ( ( A n ut
S TO STO ent puts ent ory han niti igge ctio inp
s s urr out urr teg ∞ c og l tr un red t
ut ut c
tp utp ad c C ad c y ca ow t re nne ge f owe t tes AC l al l
o u o l o y N lo et nd or ha ed p ar / V C C o va rov ova
g g . r . a f i h -c g a l s t C C A r p p pr
in in x a x w s A p
a bl abl ma xili ma x. s me oss- ngle ailin tern itial VD VA 5 V 0 V ap A a ap
a
Type En En => Au => m Ti Cr Si Tr Ex In 24 48 11 23 BG CS UL
SRB-NA-R-C.19 3 4 4 ✚ ● ● ● ✔ ✔ ✔ refer to page 88
SRB-NA-R-C.21 3 2 4 1 0,5 4 ✚ ● ● ● ✔ ✔ ✔ refer to page 92
SRB-NA-R-C.38 3 2 4 4 ✚ ● ● ● ✔ ✔ ✔ refer to page 96
* = Drop-out delay time 0 ... 30 sec. (0 ... 5.3 sec.) external setting; ✚ = fixed; = DIP switch setting;
● = selectable; ● = selectable feature; ✔ = in preparation; ✔ = approved
87
SRB-NA-R-C.19
Safety relay array for emergency stop devices,
interlocking devices and others
☛ 3 safety enabling outputs drop-out delayed: 0 ... 5.3 sec.
☛ Selectable extras:
– Trailing edge function
– Auto reset
☛ Possibility to shorten the drop-out delay
Features – Relay output: 3 NO – LED’s for K2, K3, K4, Ui – DIN rail mounting
DIN EN 50 022
– Reset, feedback loop – Housing 45 mm, made of
thermoplastic in accordance with
– Input for emergency stop UL-94-V-0, red RAL 3000
or door monitoring
Approvals
Front view
13 23 33
A1 T11 Y2 Y1 S11
SRB-NA-R-
C.19-24V Ui
Fuse K2 K3
K4
A2 S1 S2 S22 V1
14 24 34
88
SRB-NA-R-C.19 (continued)
A2 14 24 34
KA KB
N
For further examples
refer to page 90/91
Model specific
Technical data
Operating voltage 24 VDC –15%/+20%, residual ripple max. 10%
(refer to page 157 24 VAC –15%/+6%
for general data)
Frequency 50/60 Hz (for AC operating)
7
Fuse (power supply) F2: M 0.25 A/250 V (internal M 0.5 A/250 V; F3: T 0.1 A/250 V)
Power consumption max. 3 VA
Switching capacity (enabling contacts) 230 VAC, 6 A ohmic (inductive with suitable suppression)
Fuse (enabling contacts) 6 A slow blowing
Application category AC 15/DC 13, DIN VDE 0660 Part 200
Pick-up delay ≤ 100 ms
Drop-out delay Refer to page 91
Contact material / contacts AgSnO, self cleaning, positively driven
Contact resistance max. 100 mOhm when new
Air and creeping distances DIN VDE 0110-1 (04.97), 4 kV/2
Connections Self lifting screw terminals min. 0.5 qmm, max. 2.5 qmm
Dimensions H/W/D 83 mm/45 mm/140 mm
Weight 390 g
Ambient operating temperature –25 °C ... +45 °C (derating curve page 157)
Mechanical life 107 switching cycles
Terminal labeling DIN EN 50 005/DIN 50 013
89
SRB-NA-R-C.19 (continued)
Advice:
For "Automatic reset" apply S11
jumper S11-Y1.
When using external reset
button (S11-Y2) and jumper
Y1-Y2, unit is triggered by
trailing edge function. Reset
Reset button wired in series to
feedback loop.
If the time between channel 1
and 2 exceeds ca. 20 msec.
when connecting a safety limit
switch or interlocking device,
a lock function can be
achieved by triggering channel
2 (T11-S2) prior to channel 1
(T11-S1). The time difference
is then extended to infinite.
Y2 Y1
90
SRB-NA-R-C.19 (continued)
14 KB 14 24
KA
KA KB KA KB
N N
Advice: Advice:
Enabling outputs 23/24 A1 14 It is possible to shorten the A1 14
and 33/34 correspond drop-out delay time via an
to STOP category 1 external NC between
in accordance with terminals 14 and V1.
EN 60 204-1.
S1
The safety relay module
has no safety function if
connector V1 is triggered
external.
13 V1 13 V1
91
SRB-NA-R-C.21
Safety relay array for emergency stop devices,
interlocking devices and others
☛ 5 enabling outputs and 1 monitoring output
☛ 2 enabling outputs drop-out delayed: 0 ... 30 sec.
☛ Selectable extras:
– Trailing edge function
– Auto reset
– Cross-short recognition
☛ Time set in 24 stages (at bottom of housing)
Features – Relay output: 3 NO, 2 NO time – Input for emergency stop – DIN rail mounting
delayed, 1 NC or door monitoring DIN EN 50 022
(Auxiliary NC for monitoring
must not be used in safety – LED’s for K1, K2, K3, K4, UB, Ui
enabling circuits!) – Housing 45 mm, made of
– Reset, feedback loop thermoplastic in accordance with
UL-94-V-0, red RAL 3000
Approvals
ÜFZ
PR
ER
BG-
T.
Front view 47 57
13 23 33 (43) (53)
C C1 S1 X1 X2
SRB-NA-R- t ...... s
C.21-24V UB U i
Fuse K1 K3
K2 K4
D D1 S2 X2.1 L62
48 58
14 24 34 (44) (54)
92
SRB-NA-R-C.21 (continued)
D D1 L62 14 24 34 48 58
(44) (54)
KA KB
N
For further examples
refer to page 94/95
Model specific Operating voltage 24 VDC –15%/+20%, residual ripple max. 10%
Technical data 24 VAC –15%/+6%
(refer to page 157 Frequency 50/60 Hz (for AC operating)
for general data)
Fuse (power supply) T 1.0 A/250 V (internal T 1.25 A/250 V) 7
Power consumption max. 4.0 VA, plus monitoring output L62
Switching capacity (enabling contacts) 230 VAC, 4 A ohmic (inductive with suitable suppression)
NO 43/44, 53/54: DC 13: 24 VDC/2 A; AC 15: 230 VAC/3 A
Fuse (enabling contacts) 4 A slow blowing
Switching capacity (monitoring contacts) L62: max. 500 mA
Application category AC 15/DC 13, DIN VDE 0660 Part 200
Pick-up delay ≤ 30 ms
Drop-out delay ≤ 60 ms
Contact material / contacts AgSnO, self cleaning, positively driven
Contact resistance max. 100 mOhm when new
Air and creeping distances DIN VDE 0110-1 (04.97), 4 kV/2
Connections Self lifting screw terminals min. 0.5 qmm, max. 2.5 qmm
Dimensions H/W/D 83 mm/45 mm/140 mm
Weight 480 g
Ambient operating temperature –25 °C ... +45 °C (derating curve page 157)
Mechanical life 107 switching cycles
Terminal labeling DIN EN 60 445/DIN 40 719 Part 2
93
SRB-NA-R-C.21 (continued)
S1 S2 X2 S1 S2 X2
94
SRB-NA-R-C.21 (continued)
14 44 KB 14 24 48 KB
(44)
KA KB KC KA KB KC
N N
Advice: Advice:
47 57
For "Automatic reset" X1 Drop-out delay of the (43) (53)
apply jumper X1-X2. enabling outputs 47/48
When using external reset and 57/58 adjustable from
button (X1-X2.1), unit is 0–30 sec.
triggered by trailing edge Enabling outputs 43/44
function. Reset and 53/54 correspond
Reset button wired in to STOP category 1
series to feedback loop. in accordance with
EN 60 204-1.
Enabling outputs 47/48
and 57/58 correspond
to STOP category 1
7
in accordance with
EN 60 204-1.
Time S1 = 1, S1 = 0, S1 = 1, S1 = 0,
in seconds S2 = 1, S2 = 1, S2 = 0, S2 = 0,
Rear view S3 = 1, S3 = 0, S3 = 1, S3 = 0,
S4 = 1 S4 = 1 S4 = 0 S4 = 0
IV V
II
III
VI Max I 0.44 2.30 3.5 18
Min I
1 0
II 0.62 2.45 5.0 20
QS S4
1 0 S3
S2
III 0.87 2.70 7.0 22
S1
IV 1.05 2.85 8.5 23
V 1.27 3.05 10.2 25
VI 1.77 3.55 14.2 29
Tolerance: ± 5%
95
SRB-NA-R-C.38
Safety relay array for emergency stop devices,
interlocking devices and others
☛ 5 enabling outputs
☛ 2 enabling outputs drop-out delayed: 0 ... 30 seconds
☛ Selectable extras:
– Trailing edge function, – Auto reset, – Cross-short recognition
☛ Time set in 24 stages (at bottom of housing)
☛ Possibility to shorten the drop-out delay
Features – Relay output: 3 NO, 2 NO drop- – LED’s for K1, K2, K3, K4, UB – DIN rail mounting
out delayed and Ui DIN EN 50 022
– Reset, feedback loop – Housing 90 mm, made of
thermoplastic in accordance with
– Input for emergency stop UL-94-V-0, red RAL 3000
or door monitoring
Approvals
ÜFZ
PR
ER
BG-
T.
Front view
13 23 33 47 57
A1 T11 T12 T33 T34
SRB-NA-R- t: .... s
C.38-24V UB Ui
Fuse K1 K3
K2 K4
A2 T21 T22 T35 RT
14 24 34 48 58
96
SRB-NA-R-C.38 (continued)
Wiring diagram L1
Example for dual-channel door
monitoring using two limit switches
Open
(one with positive opening contacts) and
Closed **** external reset button.
KB
Reset
Dual-channel output, suitable for contact
KA reinforcement or contact multiplication,
using relays or contactors with positively
A1 T11 T34 T35 T33 T12 RT T22 13 23 33 47 57 guided contacts.
**** = Feedback loop
A2 T21 14 24 34 48 58
KA KB
N
For further examples
refer to page 98/99
Model specific Operating voltage 24 VDC –15%/+20%, residual ripple max. 10%
Technical data 24 VAC –15%/+6%
(refer to page 157 Frequency 50/60 Hz (for AC operating)
for general data)
Fuse (power supply) T 1.0 A/250 V (internal T 1.25 A/250 V) 7
Power consumption max. 4.0 VA
Switching capacity (enabling contacts) 230 VAC, 4 A ohmic (inductive with suitable suppression)
NO 43/44, 53/54: DC 13: 24 VDC/2 A; AC 15: 230 VAC/3 A
Fuse (enabling contacts) 4 A slow blowing
Application category AC 15/DC 13, DIN VDE 0660 Part 200
Pick-up delay ≤ 30 ms
Drop-out delay ≤ 60 ms
Contact material / contacts AgSnO, self cleaning, positively driven
Contact resistance max. 100 mOhm when new
Air and creeping distances DIN VDE 0110-1 (04.97), 4 kV/2
Connections Self lifting screw terminals min. 0.5 qmm, max. 2.5 qmm
Dimensions H/W/D 83 mm/45 mm/140 mm
Weight 480 g
Ambient operating temperaturer –25 °C ... +45 °C (derating curve page 157)
Mechanical life 107 switching cycles
Terminal labeling DIN EN 50 005/DIN 50 013
97
SRB-NA-R-C.38 (continued)
Wire breakage and earth Emergency Reset Wire breakage and earth Reset
leakage in the door switch off leakage in the door
monitoring circuits are monitoring circuits are
detected. detected.
Cross-shorts in the With external reset button
emergency stop circuits are for increased safety
detected. requirements.
To enable cross-short Safety category 2
monitoring: Set switch "QS" QS in accordance with QS
(bottom of housing) to 1. EN 954-1.
1 0 1 0
With external reset button.
Safety category 3 or 4 T12 T22 T34 T12 T22 T34
in accordance with
EN 954-1.
98
SRB-NA-R-C.38 (continued)
14 48 KA 14 24 48 KB
KA KB KC KA KB KC
N N
Advice: Advice:
For "Automatic reset" Drop-out delay of the 47 57
T33
apply jumper X1-X2. enabling outputs 47/48
When using external reset and 53/54 adjustable from
button (X1-X2.1), unit is 0–30 sec.
triggered by trailing edge Enabling outputs 57/58
function. Reset and 53/54 correspond
Reset button wired in to STOP category 1
series to feedback loop. in accordance with
EN 60 204-1.
Enabling outputs 47/48
and 57/58 correspond
to STOP category 1
7
in accordance with
EN 60 204-1.
T35 48 58
Time S1 = 1, S1 = 0, S1 = 1, S1 = 0,
in seconds S2 = 1, S2 = 1, S2 = 0, S2 = 0,
Rear view S3 = 1, S3 = 0, S3 = 1, S3 = 0,
S4 = 1 S4 = 1 S4 = 0 S4 = 0
IV V
III
II
VI Max I 0.44 2.30 3.5 18
Min I
1 0
II 0.62 2.45 5.0 20
QS S4
1 0 S3 III 0.87 2.70 7.0 22
S2
S1
IV 1.05 2.85 8.5 23
V 1.27 3.05 10.2 25
VI 1.77 3.55 14.2 29
Tolerance: ± 5%
99
100
SRB modules 45 mm wide,
special versions
Options
0 .1
t. t /2
ca ca A) A ) e l1 n ng ts
OP P
O nt ( uts nt ( ry nn itio geri ion npu
s S
ut ut
T S T
r e
s ur out ur teg ∞ p r e o
tp utp ad c C ad c y ca ow t re nne ge f owe t tes AC
c h a
g n
co l t
i g
r un red c t i
t
l al l
8
o u o l o y N l o et nd or ha ed p ar /V C C C o va rov ova
g g . r . a f i h c g a l s t C r p p pr
in in x a x w s - A A p
a bl abl ma xili ma x. s me oss- ngle ailin tern itial VD VA 5 V 0 V ap A a ap
u a L
Type En En => A => m Ti Cr Si Tr Ex In 24 48 11 23 BG CS U
SRB-NA-NF 3 6 3 ✚ ✚ ● ●* refer to page 102
Special feature(s): operated by battery powered networks, * = voltage 12 VDC, refer to page 159
SRB-NA-R-C.26 3 6 1 2 3 ✚ ✚ ● ✚ ✚ ✚ ✔ ✔ ✔ refer to page 106
Special feature(s): dual channel non-equivalent input circuits for humid environments, refer to page 159
✚ = fixed; ● = selectable; ✔ = in preparation; ✔ = approved
101
8
SRB-NA-NF
E-Stop module for vehicles
☛ Suitable for battery powered networks
☛ 3 safety enabling outputs
☛ Cross-short recognition
Features – Relay output: 3 NO – LED’s for K1, K2, UB – DIN rail mounting
DIN EN 50 022
– Reset, feedback loop – Housing 45 mm, made of
thermoplastic in accordance with
– Input for emergency stop UL-94-V-0, red RAL 3000
or door monitoring
Approvals
ÜFZ
PR
ER
BG-
T.
Front view
C S1.1 13 23 33
K1
UB
K2
SRB-NA-NF
D S2.1 14 24 34
102
SRB-NA-NF (continued)
N
For further examples
refer to page 104/105
Model specific Operating voltage 24 VDC, 12 VDC –25%/+35%, residual ripple 10%
Technical data
Fuse (power supply) M 0.25 A/250 V (internal M 0.5 A/250 V)
(refer to page 157
for general data) Power consumption max. 2.5 VA
Switching capacity (enabling contacts) 230 VAC, 6 A ohmic (inductive with suitable suppression)
Fuse (enabling contacts) 6 A slow blowing
Application category AC 15/DC 13, DIN VDE 0660 Part 200
Pick-up delay ≤ 30 ms
≤ 50 ms
Drop-out delay
Contact material / contacts AgSnO, self cleaning, positively driven
8
Contact resistance max. 100 mOhm when new
Air and creeping distances DIN VDE 0110-1 (04.97), 4 kV/2
Connections Self lifting screw terminals min. 0.5 qmm, max. 2.5 qmm
Dimensions H/W/D 83 mm/45 mm/127 mm
Weight 280 g
Ambient operating temperature –25 °C ... +45 °C (derating curve page 157)
Mechanical life 107 switching cycles
Terminal labeling DIN EN 60 445/DIN 40 719 Part 2
103
8
SRB-NA-NF (continued)
104
SRB-NA-NF (continued)
14 KB 14 24 KA
KA KB KA KB
N N
105
8
SRB-NA-R-C.26
Safety relay array for emergency stop devices,
interlocking devices and others
☛ Suitable for humid environments
☛ 3 enabling outputs and 1 monitoring output
☛ Non-equivalent input
☛ Cross-short recognition
Features – Relay output: 3 NO, 1 NO time – Reset, feedback loop – Housing 45 mm, made of
delayed, 1 NC thermoplastic in accordance with
(Auxiliary NC for monitoring – Input for emergency stop UL-94-V-0, red RAL 3000
must not be used in safety or door monitoring
enabling circuits!) – DIN rail mounting
– LED’s for K2, K3, UB, Ui DIN EN 50 022
Approvals
ÜFZ
PR
ER
BG-
T.
Front view
A1 13 23 33 41
T11 T23 T24 T12
SRB-NA-R-C.26
UB U i
Fuse K2 K3
T33 T34 X1 X2
A2 14 24 34 42
106
SRB-NA-R-C.26 (continued)
K1
**** = Feedback loop
F2
K1Trigger
K2 circuit
K1 K3 Wire breakage and earth leakage in the
F1
monitoring circuits are detected.
K2 KA
K3 KB
K1 K2 K3
A2 14 24 34 42
KA KB
N
For further examples
refer to page 108/109
Model specific Operating voltage 24 VDC –15%/+20%, residual ripple max. 10%
Technical data 24 VAC, 46 VAC, 115 VAC, 230 VAC –15%/+6%
(refer to page 157 Frequency 50/60 Hz (for AC operating)
for general data)
Fuse (power supply) F2: T 0.125 A/250 V (internal F1: T 0.25 A/250 V)
Power consumption max. 1.8 W, 5.5 VA
Switching capacity (enabling contacts) 230 VAC, 6 A ohmic (inductive with suitable suppression)
Fuse (enabling contacts) 6 A slow blowing
Switching capacity (monitoring contacts) 24 VDC, 2 A
Fuse (monitoring) 2 A slow blowing 8
Application category AC 15/DC 13, DIN VDE 0660 Part 200
Pick-up delay ≤ 50 ms
Drop-out delay ≤ 60 ms
Contact material / contacts AgSnO, self cleaning, positively driven
Contact resistance max. 100 mOhm when new
Air and creeping distances DIN VDE 0110-1 (04.97), 4 kV/2
Connections Self lifting screw terminals min. 0.5 qmm, max. 2.5 qmm
Dimensions H/W/D 83 mm/90 mm/127 mm
Weight 460 g (600 g at 230 V and 115 V version)
Ambient operating temperature –25 °C ... +45 °C (derating curve page 157)
Mechanical life 107 switching cycles
Terminal labeling DIN EN 50 005/DIN 50 013
107
8
SRB-NA-R-C.26 (continued)
108
SRB-NA-R-C.26 (continued)
14 KB 14 24 KA
KA KB KA KB
N N
109
8
110
SRB modules 90 mm wide,
standard version
Options
0 .1
OP
t.
P
t
ca ca A) uts A)
O nt ( utp nt ( ry
l1 n
/2
g
n io erin on puts
e 9
a n t
S T S T e o e o h n i g g cti in
u ts uts curr /NO curr teg ∞ c cog l tri fun red t
tp tp d C d ca w re ne e we tes C l al l
ou g ou loa y N loa ety ndo ort han edg l po art /VA C C o va rov ova
g . r . a f i h c g a s t C C A r p p pr
in in x a x w s - A p
a bl abl ma xili ma x. s me oss- ngle ailin tern itial VD VA 5 V 0 V ap A a ap
a
Type En En => Au => m Ti Cr Si Tr Ex In 24 48 11 23 BG CS UL
SRB-NA-R-C.8/97 3 6 1/1 2 4 ✚ ● ● ● ● ● ✔ ✔ ✔ refer to page 112
✚ = fixed; ● = selectable; ● = selectable feature; ✔ = approved
111
SRB-NA-R-C.8/97
Safety relay array for emergency stop devices,
interlocking devices and others
☛ 3 enabling outputs and 2 monitoring outputs
☛ Selectable extras:
– Trailing edge function
– Auto reset
Features – Relay output: 3 NO, 2 NO/NC – Input for emergency stop – DIN rail mounting
(Auxiliary NO/NC for monitoring or door monitoring DIN EN 50 022
must not be used in safety
enabling circuits!) – LED’s for K1, K2, UB und Ui
Approvals
ÜFZ
PR
ER
BG-
T.
UB Ui
K2 K3
T33 T34
(S33) (S34) X3 X4 14 24 34 42 54 A2
112
SRB-NA-R-C.8/97 (continued)
Wiring diagram L1
Example for dual channel door
monitoring using two limit switches
Open
(one with positive opening contacts) and
Closed
external reset button.
Reset
**** Dual-channel output, suitable for contact
KA KB reinforcement or contact multiplication,
using relays or contactors with positively
A1 T11 T33 X4 X3 T34 T12 T22 X5 13 23 33 41 53
guided contacts.
F2
K1
**** = Feedback loop
F1
K2 K1 K1 K2 K1 K3 K1
Wire breakage and earth leakage in the
monitoring circuits are detected.
K2 KA
K2A
K3 K2 K3
K3 KB
K1 K2 K2A K3 K3A K3A
A2 14 24 34 42 54
KA KB
N
For further examples
refer to page 114/115
Model specific Operating voltage 24 VDC –15%/+20%, residual ripple max. 10%
Technical data 24 VAC –15%/+6%
(refer to page 157 Frequency 50/60 Hz (for AC operating)
for general data)
Fuse (power supply) F2: M 0.25 A/250 V (internal F1: M 0.5 A/250 V)
Power consumption max. 2.4 W, 4.6 VA
Switching capacity (enabling contacts) 230 VAC, 6 A ohmic (inductive with suitable suppression)
Fuse (enabling contacts) 6 A slow blowing
Switching capacity (monitoring contacts) max. 24 VDC/2 A ohmic (inductive with suitable suppression)
Fuse (monitoring contacts) 2 A slow blowing
Application category AC 15/DC 13, DIN VDE 0660 Part 200
Pick-up delay ≤ 200 ms
Drop-out delay ≤ 20 ms
Contact material / contacts
Contact resistance
AgSnO, self cleaning, positively driven
max. 100 mOhm when new
9
Air and creeping distances DIN VDE 0110-1 (04.97), 4 kV/2
Connections Self lifting screw terminals min. 0.6 qmm, max. 2.5 qmm
Dimensions H/W/D 83 mm/90 mm/127 mm
Weight 500 g
Ambient operating temperature –25 °C ... +45 °C (derating curve page 157)
Mechanical life 107 switching cycles
Terminal labeling DIN EN 50 005/DIN 50 013
113
SRB-NA-R-C.8/97 (continued)
114
SRB-NA-R-C.8/97 (continued)
14 KB 14 24 KA
KA KB KA KB
N N
T34 X4 T34 X5 X4
115
116
SRB modules 90 mm wide,
special versions
☛ Distinct restart
☛ Monitored contact multiplication
☛ 2-voltage version
☛ With separate output to operate solenoids
☛ max. 3 enabling outputs and 1 monitoring output
☛ max. 8 enabling outputs
☛ max. load current: 6 Ampere
☛ max. safety category: 4
☛ 1- or 2-channel triggering
☛ Trailing edge function selectable
☛ Semiconductor monitoring outputs selectable
☛ Initial start test selectable
☛ 24 VDC/VAC, 48 VAC, 115 VAC and 230 VAC versions
☛ Approvals: BG, CSA, UL
Options
0 .1 2
t. t 1/
ca ca A) uts A) el on ring n s
OP O P ( t p ( n ut
S T ST ent ou ent ory han niti igge ctio inp
s s urr NO urr teg ∞ c og l tr un red t
ut ut c
tp utp ad c C/ ad c y ca ow t re nne ge f owe t tes AC l al l
o u o l o y N lo et nd or ha ed p ar / V C C o va rov ova
g g . r . a f i h c g a l s t C C A r p p pr
in in x a x w s - A p
a bl abl ma xili ma x. s me oss- ngle ailin tern itial VD VA 5 V 0 V ap A a ap
a
Type En En => Au => m Ti Cr Si Tr Ex In 24 48 11 23 BG CS UL
SRB-NA-R-C.25 3 6 1 2 4 ● ● ✚ ● ● ● ● ● ✔ ✔ ✔ refer to page 118
Special feature(s): distinct restart, refer to page 158 8
SRB-2NA-R-E 3 6 4 ✚ ● ● ● ✚ ✚ ✚ ✚ ✔ ✔ refer to page 122
SRB-FE-R 5 6 ✚ ✚ ✚ ✚ ✚ ✔ ✔ refer to page 126
Special feature(s): monitored contact multiplication (using ribbon cable) , refer to page 160
SRB-QS.1/QS.2 3 6 1/1 2 4 ✚ ✚ ● ● ● ✚ ✚ ✚ ✔ ✔ ✔ refer to page 130
Special feature(s): 2-voltage-version: selectable 24 VDC/115 VAC or 24 VDC/230 VAC 1
SRB-TF-R 3 6 1 4 ✚ ● ● ● ● ✚ ✚ ✚ ✔ ✔ refer to page 134 0
SRB-TM-R 3 6 1 4 ✚ ● ● ● ● ✚ ✚ ✚ ✔ ✔ ✔ refer to page 138
Special feature(s): With separat output to operate solenoids, refer to page 161
✚ = fixed; ● = selectable; ● = selectable feature; ✔ = in preparation; ✔ = approved
117
SRB-NA-R-C.25
Safety relay array for emergency stop devices,
interlocking devices and others
☛ Distinct restart
☛ 3 safety enabling outputs and 1 monitoring output
☛ Selectable extra:
– Cross-short recognition
Features – Relay output: 3 NO, 1 NC – Input for emergency stop – DIN rail mounting
(Auxiliary NC for monitoring or door monitoring DIN EN 50 022
must not be used in safety
enabling circuits!) – LED’s for K2, K3, UB und Ui
Approvals
ÜFZ
PR
ER
BG-
T.
Front view
A1 T11 T12 T22 T21 13 23 33 41 PE
SRB-NA-R-C.25
UB Ui
K2 K3
118
SRB-NA-R-C.25 (continued)
K1
**** = Feedback loop
F2
Trigger
circuit K1 K2 K1 K3 Wire breakage and earth leakage in the
F1 K2
monitoring circuits are detected.
K2 KA
K3
K3 KB
K1 K2 K3
A2 T21 PE T23 14 24 34 42
KA KB
Model specific Operating voltage 24 VDC –15%/+20%, residual ripple max. 10%
Technical data 24 VAC, 115 VAC, 230 VAC –15%/+6%
(refer to page 157 Frequency 50/60 Hz (for AC operating)
for general data)
Fuse (power supply) F2: T 0.25 A/250 V (internal F1: T 0.5 A/250 V)
Power consumption max. 2.4 W, 4.6 VA
Switching capacity (enabling contacts) 230 VAC, 6 A ohmic (inductive with suitable suppression)
Fuse (enabling contacts) 6 A slow blowing
Switching capacity (monitoring contacts) 24 VDC, 2 A
Fuse (monitoring contacts) 2 A slow blowing
Application category AC 15/DC 13, DIN VDE 0660 Part 200
Pick-up delay ≤ 200 ms (Start button), < 450 ms (Auto-Start)
Drop-out delay ≤ 20 ms
Contact material / contacts AgSnO, self cleaning, positively driven
Contact resistance max. 100 mOhm when new
Air and creeping distances DIN VDE 0110-1 (04.97), 4 kV/2
Connections Self lifting screw terminals min. 0.5 qmm, max. 2.5 qmm
Dimensions
Weight
H/W/D 83 mm/90 mm/127 mm
450 g (600 g at 230 V and 115 V version)
1
Ambient operating temperature –25 °C ... +45 °C (derating curve page 157)
0
Mechanical life 107 switching cycles
Terminal labeling DIN EN 50 005/DIN 50 013
119
SRB-NA-R-C.25 (continued)
120
SRB-NA-R-C.25 (continued)
14 KB 14 24
KA
KA KB KA KB
N N
1
0
121
SRB-2NA-R-E
Safety relay array for emergency stop devices,
interlocking devices and others
☛ Monitored contact multiplication
☛ 3 safety enabling outputs
☛ 8 safety enabling outputs with extension module SRB-FE-R
Approvals
ÜFZ
PR
ER
BG-
T.
Front view
A1
(+) 1 2 13 23 33 43
SRB-2NA-R-E
K2 K3
A2
5 6 7 8 PE 14 24 34 44 (–)
122
SRB-2NA-R-E (continued)
K1 K2 K3
K3
KB
3 4 8 9 6 7 10
A2(–) PE 24 34 44
KA KB
N
For further examples
refer to page 124/125
Model specific Operating voltage 24 VDC –15%/+20%, residual ripple max. 10%
Technical data 24 VAC, 115 VAC, 230 VAC –15%/+6%
(refer to page 157 Frequency 50/60 Hz (for AC operating)
for general data)
Fuse (power supply) M 0.25 A/250 V (internal M 0.5 A/250 V)
Power consumption max. 2.4 W, 4.6 VA
Switching capacity (enabling contacts) 230 VAC, ohmic (inductive with suitable suppression)
Fuse (enabling contacts) 6 A slow blowing
Switching capacity (monitoring contacts) 13/14 24 VDC/2 A (only together with SRB-FE-R)
Fuse (monitoring contacts) 13/14 2 low blowing
Application category AC 15/DC 13, DIN VDE 0660 Part 200
Pick-up delay ≤ 200 ms
Drop-out delay ≤ 20 ms
Contact material / contacts AgSnO, self cleaning, positively driven
Contact resistance max. 100 mOhm when new
Air and creeping distances DIN VDE 0110-1 (04.97), 4 kV/2
Connections Self lifting screw terminals min. 0.5 qmm, max. 2.5 qmm
Dimensions
Weight
H/W/D 83 mm/90 mm/127 mm
600 g (850 g at 230 V and 115 V version)
1
Ambient operating temperature –25 °C ... +45 °C (derating curve page 157)
0
Mechanical life 107 switching cycles
Terminal labeling DIN EN 50 005/DIN 50 013
123
SRB-2NA-R-E (continued)
7 8 2 7 8 2
Wiring example:
Input level
1 1
Dual-channel door
monitoring according to Open
EN 1088, one limit switch Closed
with positive opening
contact.
Reset
Wire breakage and earth
leakage in the door
monitoring circuits are
detected.
Cross-shorts in the door
monitoring circuits are
not detected.
With external reset button
for increased safety
requirements.
Safety category 3 or 4 7 8 2
in accordance with
EN 954-1.
124
SRB-2NA-R-E (continued)
Advice: Advice:
Module can be used as a The max. load of safety
basic safety relay module enabling output 13/14 is
or as a combination limited to 2 A/24 VDC, 13
module with the extension due to technical reasons of
SRB-2NA-R-E
module SRB-FE-R. the ribbon cable. Refer to
The contact multiplication technical data.
must be done via a ribbon
SRB-2NA-R-E
cable.
The end connector of the
base module will be
exchanged in this case with SRB-FE-R
the ribbon cable.
The safety enabling output
13/14 can only be used in SRB-FE-R
combination with the
extension module. 14
14 KB 14 24
KA
1
0
KA KB KA KB
N N
125
SRB-FE-R
Safety relay array for emergency stop devices,
interlocking devices and others
☛ 8 safety enabling outputs with basic module SRB-2NA-R-E
Features – Relay output: 5 NO – LED’s for K2A, K3A – DIN rail mounting
DIN EN 50 022
– Input for emergency stop – Housing 90 mm, made of
or door monitoring thermoplastic in accordance with
UL-94-V-0, red RAL 3000
Approvals
ÜFZ
PR
ER
BG-
T.
Front view A1
(+) 53 63 73 83
SRB-FE-R
K2A K3A
A2
PE 14 54 64 74 84 (–)
126
SRB-FE-R (continued)
A1(+) 53 63 73 83
10
3 8 9 4 6 7
K1
K2 K3 K1
K2
K2
K3
K3 K2
K3
K1 K2 K3
A2(–) PE 54 64 74 84 14
Model specific Operating voltage 24 VDC –15%/+20%, residual ripple max. 10%
Technical data 24 VAC, 230 VAC –15%/+6%
(refer to page 157 Frequency 50/60 Hz (for AC operating)
for general data)
Fuse (power supply) M 0.25 A/250 V (internal M 0.5 A/250 V)
Power consumtion max. 1.2 VA
Switching capacity (enabling contacts) 230 VAC, 6 A ohmic (inductive with suitable suppression)
Fuse (enabling contacts) 6 A slow blowing
Switching capacity (monitoring contacts) 13/14 24 VDC, 2 A (only together with SRB-2NA-R-E)
Fuse (monitoring contacts) 13/14 2 A slow blowing
Application category AC 15/DC 13, DIN VDE 0660 Part 200
Pick-up delay ≤ 200 ms
Drop-out delay ≤ 20 ms
Contact material / contacts AgSnO, self cleaning, positively driven
Contact resistance max. 100 mOhm when new
Air and creeping distances DIN VDE 0110-1 (04.97), 4 kV/2
Connections Self lifting screw terminals min. 0.5 qmm, max. 2.5 qmm
Dimensions
Weight
H/W/D 83 mm/90 mm/127 mm
710 g (850 g at 230 V version)
1
Ambient operating temperature –25 °C ... +45 °C (derating curve page 157)
0
Mechanical life 107 switching cycles
Terminal labeling DIN EN 50 005/DIN 50 013
127
SRB-FE-R (continued)
Advice: Advice:
Module SRB-2NA-R-E The max. load of safety
can be used as a basic enabling output 13/14 is
safety relay module or as limited to 2 A/24 VDC, 13
a combination module due to technical reasons of
SRB-2NA-R-E
with the extension module the ribbon cable. Refer to
SRB-FE-R. technical data.
The contact multiplication
SRB-2NA-R-E
must be done via a ribbon
cable.
The end connector of the
base module will be SRB-FE-R
exchanged in this case with
the ribbon cable.
The safety enabling output SRB-FE-R
13/14 can only be used in
combination with the 14
extension module.
128
Notes
1
0
129
SRB-QS.1/SRB-QS.2
Safety relay array for emergency stop devices,
interlocking devices and others
☛ 2-voltage version
☛ 3 safety enabling outputs and 1 monitoring output
☛ Cross-short recognition
☛ Wipe contact
Features – Relay output: 3 NO, 1 NO, – Input for emergency stop – DIN rail mounting
1 wipe contact or door monitoring DIN EN 50 022
(Auxiliary NC for monitoring
must not be used in safety – LED for UN
enabling circuits!) – Housing 90 mm, made of
– Reset, feedback loop thermoplastic in accordance with
UL-94-V-0, red RAL 3000
Approvals
ÜFZ
PR
ER
BG-
T.
Front view
13 23 33
A1 E11 E21 43 51
24V B1 X5 E12 E22
UN
SRB-QS.x
E34 X1 X2
A2 0V PE 44 52
14 24 34
130
SRB-QS.1/SRB-QS.2 (continued)
K1
K3 K2 K1 KB
A2 PE 0 V E21 14 24 34 52 44
KA KB
N
For further examples
refer to page 132/133
Model specific Operating voltage 24 VDC –15%/+20%, residual ripple max. 10%
Technical data 115 VAC –15%/+6% (SRB-QS.1), 230 VAC –15%/+6% (SRB-QS.2)
(refer to page 157 Frequency 50/60 Hz (for AC operating)
for general data)
Fuse (power supply) M 0.25 A/250 V (internal M 0.5 A/250 V)
Power consumption max. 3.9 VA
Switching capacity (enabling contacts) 230 VAC, 6 A ohmic (inductive with suitable suppression)
Fuse (enabling contacts) 6 A slow blowing
Switching capacity (monitoring contacts) 24 VDC, 2 A ohmic (inductive with suitable suppression)
Fuse (monitoring contacts) 2 A slow blowing
Application category AC 15/DC 13, DIN VDE 0660 Part 200
Pick-up delay ≤ 200 ms
Drop-out delay ≤ 30 ms
Contact material / contacts AgCdO self cleaning, positively driven
Contact resistance max. 100 mOhm when new
Air and creeping distances DIN VDE 0110-1 (04.97), 4 kV/2
Connections Self lifting screw terminals min. 0.5 qmm, max. 2.5 qmm
Dimensions
Weight
H/W/D 83 mm/90 mm/140 mm
700 g
1
Ambient operating temperature –25 °C ... +45 °C (derating curve page 157)
0
Mechanical life 107 switching cycles
Terminal labeling DIN EN 50 005/DIN 50 013
131
SRB-QS.1/SRB-QS.2 (continued)
Cross-shorts in the
emergency stop circuits are
detected.
With external reset button.
Safety category 3 or 4
in accordance with
EN 954-1.
Wiring example:
Input level
E11 44 X1 Advice:
Start with trailing edge
function. LED (UN) is only ON if triggering circuits are
activated.
Module is activated after
release of the reset button. Reset
This prevents tampering of
the reset button which
could lead to an automatic
reset.
E34 43 X5 X2
132
SRB-QS.1/SRB-QS.2 (continued)
14 KB 14 24 KA
KA KB KA KB
N N
1
0
133
SRB-TF-R
Safety relay array for emergency stop devices,
interlocking devices and others
☛ With separate output to operate solenoids
suitable for spring forced interlocking devices
☛ 3 safety enabling outputs
Approvals
ÜFZ
PR
ER
BG-
T.
Front view A1
(+) 1 2 3 PE 13 23 33
SRB-TF-R
K2 K3
A2
5 6 8 8.1 14 24 34 (–)
134
SRB-TF-R (continued)
K3 K1 K2 K1 K2 K1 K3
Wire breakage and earth leakage in the
monitoring circuits are detected.
K2 KA
** Fuse M 0.5 A
K3 K2 K3 (an external leading fuse
M 0.25 A is recommended)
K3 KB
K1 K2 K3
A2 PE 14 24 34
KA KB
Model specific Operating voltage 24 VDC –15%/+20%, residual ripple max. 10%
Technical data 24 VAC, 115 VAC, 230 VAC –15%/+6%
(refer to page 157 Frequency 50/60 Hz (for AC operating)
for general data)
Fuse (power supply) F2: T 0.25 A/250 V (internal F1: T 0.5 A/250 V)
Power consumption max. 3.6 VA
Switching capacity (enabling contacts) 230 VAC, 6 A ohmic (inductive with suitable suppression)
Fuse (enabling contacts) 6 A slow blowing
Application category AC 15/DC 13, DIN VDE 0660 Part 200
Pick-up delay ≤ 200 ms
Drop-out delay ≤ 20 ms
Contact material / contacts AgCdO, self cleaning, positively driven
Contact resistance max. 100 mOhm when new
Air and creeping distances DIN VDE 0110-1 (04.97), 4 kV/2
Connections Self lifting screw terminals min. 0.5 qmm, max. 2.5 qmm
Dimensions H/W/D 83 mm/90 mm/127 mm
Weight 580 g (830 g at 230 V and 115 V version)
–25 °C ... +45 °C (derating curve page 157)
Ambient operating temperature
Mechanical life 107 switching cycles
1
Terminal labeling DIN EN 50 005/DIN 50 013
0
135
SRB-TF-R (continued)
8 8.1 2 8 8.1 2
8 8.1 2 8 8.1 2 1
136
SRB-TF-R (continued)
14 KB 14 24
KA
KA KB KA KB
N
N
1
0
137
SRB-TM-R
Safety relay array for emergency stop devices,
interlocking devices and others
☛ With separate output to operate solenoids
suitable for electro-magnetic forced interlocking devices
☛ 3 safety enabling outputs
Approvals
ÜFZ
PR
ER
BG-
T.
Front view
A1
(+) 1 2 3 13 23 33
SRB-TM-R
K2 K3
A2
5 7 8 8.1 14 24 34 (–)
138
SRB-TM-R (continued)
Wiring diagram L1
Example for dual-channel door
monitoring using two limit switches
Open
KB Closed
(one with positive opening contacts) and
**** external reset button.
KA
Dual-channel output, suitable for contact
Reset reinforcement or contact multiplication,
using relays or contactors with positively
A1 5 3 7 1 2 8 8.1 13 23 33 guided contacts.
**
F1 **** = Feedback loop
K1
K3 K1 K2 K1 K2 K1 K3
Wire breakage and earth leakage in the
monitoring circuits are detected.
K2 KA
** Fuse M 0.5 A
K3 K2 K3 (an external leading fuse
M 0.25 A is recommended)
K3 KB
K1 K2 K3
A2 PE 14 24 34
KA KB
Model specific Operating voltage 24 VDC –15%/+20%, residual ripple max. 10%
Technical data 24 VAC, 115 VAC, 230 VAC –15%/+6%
(refer to page 157 Frequency 50/60 Hz (for AC operating)
for general data)
Fuse (power supply) M 0.25 A/250 V (internal M 0.5 A/250 V)
Power consumption max. 3.6 VA
Switching capacity (enabling contacts) 230 VAC, 6 A ohmic (inductive with suitable suppression)
Fuse (enabling contacts) 6 A slow blowing
Application category AC 15/DC 13, DIN VDE 0660 Part 200
Pick-up delay ≤ 200 ms
Drop-out delay ≤ 20 ms
Contact material / contacts AgCdO, self cleaning, positively driven
Contact resistance max. 100 mOhm when new
Air and creeping distances DIN VDE 0110-1 (04.97), 4 kV/2
Connections Self lifting screw terminals min. 0.5 qmm, max. 2.5 qmm
Dimensions H/W/D 83 mm/90 mm/127 mm
Weight 580 g (830 g at 230 V and 115 V version)
–25 °C ... +45 °C (derating curve page 157)
Ambient operating temperature
Mechanical life 107 switching cycles
1
Terminal labeling DIN EN 50 005/DIN 50 013
0
139
SRB-TM-R (continued)
8 8.1 2 8 8.1 2
8 8.1 2 8 8.1 2 1
140
SRB-TM-R (continued)
14 KB 14 24
KA
KA KB KA KB
N
N
1
0
141
142
Modules for contact multiplying
0 .1 2
t. t 1/
ca ca A) el on ring n ts
P P ( n
T O TO ) u t n t ry a n iti ge io npu
S s S (A tp rre go ch ogn trig nc ed t i
ts
pu tpu ren C o d c cat w ∞ rec nel ge f wer test AC
t t u u e u
t l al l
o u o u
c u r
y N l o a
e t y n d o
o r t
h a n
e d p o rt /V
a C C o va rov ova
g g
lin lin ad lia ax sa
r . f wi h
s-s e- in
c g nal l st DC AC A A ppr app ppr
n ab nab > lo uxi > m ax. ime ros ingl rail xter itia 4 V 8 V 15 V 30 V G a SA L a
Type E E = A = m T C S T E In 2 4 1 2 B C U
SRB-NA-R-C.EW 4 6 ● ✔ ✔ refer to page 144
SRB-ZB-Mo 6 6 ● ✔ ✔ refer to page 148
SRB-LV 4 6 1 2 ● ● ● ● ✔ ✔ refer to page 152
● = selectable; ✔ = approved
1
143
1
SRB-NA-R-C.EW
Output expansion module for additional enabling outputs
☛ 4 enabling outputs
☛ 22.5 mm housing
Features – Relay output: 4 NO – Housing 22.5 mm, made of – DIN rail mounting
thermoplastic in accordance with DIN EN 50 022
– LED’s for K1, K2 UL-94-V-0, red RAL 3000
– Feedback circuit X1, X2
Approvals
Front view
13 23 33
X2 X1 A1
K2
SRB-NA
-R-C.EW
K1
14 24 34
A2 43 44
144
SRB-NA-R-C.EW (continued)
Wiring diagram
A1 X1 13 23 33 43
K1
K1
K1
K2
K2 K2
K1 K2
A2 X2 14 24 34 44
For further examples
refer to page 146/147
Model specific Operating voltage 24 VDC –15%/+20%, residual ripple max. 10%
Technical data 24 VAC –15%/+6%
(refer to page 157 Frequency 50/60 Hz (for AC operating)
for general data)
Fuse (power supply) M 0.25 A/250 V
Power consumption max. 1.2 VA
Switching capacity (enabling contacts) 230 VAC, 6 A ohmic (inductive with suitable suppression)
Application category AC 15/DC 13, DIN VDE 0660 Part 200
Pick-up delay ≤ 20 ms
Drop-out delay ≤ 35 ms
Contact material / contacts AgSnO, self cleaning, positively driven
Contact resistance max. 100 mOhm when new
Air and creeping distances DIN VDE 0110-1 (04.97), 4 kV/2
Connections Self lifting screw terminals min. 0.6 qmm, max. 2.5 qmm
Dimensions H/W/D 82 mm/22.5 mm/98 mm
Weight 190 g
Ambient operating temperature –25 °C ... +45 °C (derating curve page 157)
Mechanical life 107 switching cycles
Terminal labeling DIN EN 60 445/DIN 40 719 Part 2
1
145
1
SRB-NA-R-C.EW (continued)
Wiring example:
Input level 24 V
Single-channel control of
the expansion module
SRB-NA-R-C.EW via one
enabling output of the base
module.
A fault in the expansion
module is not detected by X1 X2 13 23 A1 X1 X2
the base module. Base module Expansion module
Connect terminals X1 and SRB-NA-... SRB-NA-R-C.EW
X2 to the feedback loop of 14 24 A2
the base module.
0V
Advice:
Warning !
The expansion module
must be installed according
to the example since the
device is not fitted with its
own safety circuits.
146
Notes
1
147
1
SRB-ZB-Mo
Output expansion module for additional enabling outputs
☛ 6 enabling outputs
☛ 90 mm housing
Approvals
Front view
B1 B2 X1 X11 13 23 33 43 53 63
B1 B2
SRB-ZB-Mo
B10 B20
A B12 X2 X12 14 24 34 44 54 64
148
SRB-ZB-Mo (continued)
Wiring diagram
B1 B2 B12 X1 X11 13 23 33 43 53 63
B1 B10
B1 B10
B2 B20 B2 B20
B1 B2 B10 B20
A X2 X12 14 24 34 44 54 64
Model specific Operating voltage 24 VDC –15%/+20%, residual ripple max. 10%
Technical data
Fuse (power supply) M 0.25 A/250 V
(refer to page 157
for general data) Power consumption max. 2.4 W
Switching capacity (enabling contacts) 230 VAC, 6 A ohmic (inductive with suitable suppression)
Fuse (enabling contacts) 6 A slow blowing
Application category AC 15/DC 13, DIN VDE 0660 Part 200
Pick-up delay ≤ 30 ms
Drop-out delay ≤ 20 ms
Contact material / contacts AgSnO, self cleaning, positively driven
Contact resistance max. 100 mOhm when new
Air and creeping distances DIN VDE 0110-1 (04.97), 4 kV/2
Connections Self lifting screw terminals min. 0.5 qmm, max. 2.5 qmm
Dimensions H/W/D 83 mm/90 mm/127 mm
Weight 470 g
Ambient operating temperature –25 °C ... +45 °C (derating curve page 157)
Mechanical life 107 switching cycles
Terminal labeling DIN EN 50 005/DIN 50 013
1
149
1
SRB-ZB-Mo (continued)
Wiring example:
Input level
L (L+)
Single-channel control of
the expansion module
SRB-NA-R-C.EW via one
enabling output of the base
module.
A fault in the expansion
module is not detected by X1 X2 13 23 X1 X2 X11 X12
the base module. Base module Expansion module
SRB-NA-... A SRB-ZB-Mo
Connect terminals X1 and
X2 to the feedback loop of 14 24 B1 B2 B12
the base module.
N (L–)
Wiring example:
Input level
Dual-channel control of L (L+)
the expansion module
SRB-NA-R-C.EW via two
enabling output of the base
module.
A fault in the expansion
module is not detected by X1 X2 13 23 X1 X2 X11 X12
the base module. Base module Expansion module
Connect terminals X1, X2 SRB-NA-... A SRB-ZB-Mo
and X11, X12 to the 14 24 B1 B2 B12
feedback loop of the base
module.
N (L–)
Advice:
WARNING: The expansion
module must be installed
according to the example
shown since the device is
not fitted with its own
safety monitoring.
150
Notes
1
151
1
SRB-LV
Output expansion module for additional enabling outputs
☛ 4 enabling outputs and 1 monitoring output
☛ 90 mm housing
Features – Relay output: 4 NO, 1 NC – LED’s for K1, K2 – Housing 90 mm, made of
(Auxiliary NC for monitoring thermoplastic in accordance with
must not be used in safety – Feedback circuit X1, X2 UL-94-V-0, red RAL 3000
enabling circuits!)
– DIN rail mounting
DIN EN 50 022
Approvals
Front view A1
(+) U K1 X1 13 23 33 43 51
SRB-LV
K1 K2
A2
(–) U PE K2 X2 14 24 34 44 52
152
SRB-LV (continued)
Wiring diagram
A1 U U K1 K2 X1 13 23 33 43 51
K1
K1
K1
K2
K2 K2
K1 K2
A2 PE X2 14 24 34 44 52
Model specific Operating voltage 24 VDC –15%/+20%, residual ripple max. 10%
Technical data 24 VAC, 115 VAC, 230 VAC –15%/+6%
(refer to page 157 Frequency 50/60 Hz (for AC operating)
for general data)
Fuse (power supply) M 0.25 A/250 V
Power consumption max. 1.2 VA
Switching capacity (enabling contacts) 230 VAC, 6 A ohmic (inductive with suitable suppression)
Fuse (enabling contacts) 6 A slow blowing
Switching capacity (monitoring contacts) 24 VDC/2 A
Fuse (monitoring contacts) 2 A slow blowing
Application category AC 15/DC 13, DIN VDE 0660 Part 200
Pick-up delay ≤ 20 ms
Drop-out delay ≤ 20 ms
Contact material / contacts AgSnO, self cleaning, positively driven
Contact resistance max. 100 mOhm when new
Air and creeping distances DIN VDE 0110-1 (04.97), 4 kV/2
Connections Self lifting screw terminals min. 0.6 qmm, max. 2.5 qmm
Dimensions H/W/D 83 mm/90 mm/127 mm
Weight 410 g (500 g at 115 V and 230 V version)
Ambient operating temperature –25 °C ... +45 °C (derating curve page 157)
Mechanical life 107 switching cycles
Terminal labeling DIN EN 60 445/DIN 40 719 Part 2
1
153
1
SRB-LV (continued)
Wiring example:
Input level
Single-channel control of L (L+)
the expansion module
SRB-LV via one enabling
output of the base module.
A fault in the expansion
module is not detected by
the base module. X1 X2 13 23 U U X1 X2
A1
Connect terminals X1 and Base module Expansion module
X2 to the feedback loop of SRB-NA-... A2 SRB-LV
the base module. 14 24 K1 K2
N (L-)
Wiring example:
Input level
L (L+)
Dual-channel control of
the expansion module
SRB-LV via one enabling
output of the base module.
A fault in the expansion
module is not detected by
the base module. X1 X2 13 23 U U X1 X2
A1
Connect terminals X1 and Base module Expansion module
X2 to the feedback loop of SRB-NA-... A2 SRB-LV
the base module. 14 24 K1 K2
N (L-)
Advice:
Warning !
The expansion module
must be installed according
to the example since the
device is not fitted with its
own safety circuits.
154
Notes
1
155
1
156
General technical data
EMC Interference suppression Integrated suppressor, electronic EMC suppressor circuit if necessary
Approvals BG, CSA, UL Refer to product ranges (copies available upon request)
Derating curve
SRB-... Ampere
6.0
5.0
Safety enabling outputs with switching
4.0 capacity of 6 A
3.0
Safety enabling outputs with switching
2.0 capacity of 4 A
1.0
0
40 45 50 55 60
Ambient operating temperature
1
157
1
Modules for special applications
Modules for
contact multi-
plying
Modules SRB-NA-R-C.EW, However, the availability is different inputs are interrupted. Also after
SRB-LV and SRB-ZB-MO are compared to the SRB combination restart only the enabling outputs of
designed for multiplying of SRB-2NA-R-E/SRB-FE-R for 8 the basic module will be activated,
enabling outputs of other SRB enabling outputs. In case of a broken but not those of the contact multi-
modules. wire between the basic module and plying module.
the contact multiplying module just
Due to a feed back loop to the SRB the additional enabling outputs of
module also in the contact multiply- the contact multiplying module will
ing module the same safety level disconnect at once. The enabling
(category 3 or category 4) is outputs of the basic module will
achieved as in the corresponding disconnect only when the safety
basic module.
Distinct restart SRB module C.25 is equipped with This feature for SRB module C.25
a particular restart circuit. The was developed for applications in
module itself determines which which a restart via Reset button
event has caused the drop out of the would require an unreasonable lot of
enabling outputs. If for instance a performance, i.e. in large installa-
loss in power or because a protective tions with decentralized locations of
device was operated. E-Stops and protective devices
where only short time supply
Automatic restart is provided after a failures may cause a drop out of the
previous power down situation, relay circuit. In situations however,
whilst a restart after operating a when a safety device was operated a
protective device needs an extra manual restart is essential. The
restart signal. function of “distinct restart” needs a
special risk assessment by the user
in order to make sure, that the ▲ Example of SRB module with
automatic restart function does not distinct restart
involve a risk for personal protection
function.
158
Dual channel Customarily dual channel inputs for contact is provided. The monitoring
antivalent input SRB modules have the same of these distinct input circuits
circuits for operating principle, normally based enables for instance to detect the
humid environ- on two NC contacts, one of these at ingress of a conductive liquid into an
least with positive opening function. external safety device.
ments
For SRB module C.26 in particular
an antivalent input circuit, one
consisting of a positively opening
NC contact and the other of a NO
▲
dual channel antivalent input
circuits for humid environments
SRB modules The typical inconstancy of the –25% to +35% of the supply
operated by voltage in battery powered ship and voltage. Furthermore the voltage
battery powered vehicle networks makes it critical to regulator is designed to cope with
networks in use standard safety relay circuits in typical situations in such networks
such a supply system. i.e. the critical interference caused
vehicles and
by "load" and "dump".
others The characteristics of the SRB
modules SRB-NA-NF is an extra
integrated voltage regulator which
can accomodate tolerances from
SRB modules The specific feature of this SRB or as a selfholding contact via the
with output module is an extra output to drive guard monitoring contact in case of
to operate the solenoids in interlocking devices automatic interlocking.
solenoids with guard-locking function, either
for devices interlocked by spring
force or interlocked by electro
magnetic force. This additional
contact serves as a selfholding
contact for the interlock pushbutton
▲
159
Modules for special applications (continued)
SRB combi- This module combination consists of A broken wire in hard wired contact
nation modules the basic module SRB-2NA-R-E multiplying circuits would shut
for 8 enabling (with termination plug = 3 enabling down the enabling outputs in the
outputs outputs) and the extension module extension module only and the
SRB-FE-R (with ribbon cable = 8 failure detection via a process
enabling outputs). interrupt is not guaranteed.
Therefore wiring errors can be
excluded.
▲
Example of SRB modules
for 8 enabling outputs
SRBF modules The housing SRBF is designed for Further special features of the SRBF
relay circuits with high complexity housings:
and therefore more space consuming
because of the number of relays and • connection via quick disconnect
other components. strips, alternatively with screw
terminals or with cage clamps,
In all situations where modules with
45 mm, 90 mm and more are an • convenient setting for mode,
obstacle because of the dimension, delay time etc. via DIP switches.
the circuits might be redesigned into
a shape fitting into the SRBF
housing. The described SRBF are
only representative examples.
Muting controls
refer to catalogue
SRB-MS
Two-hand relay
modules
refer to customer
information or
catalogue ZHS
160
Scope of products
Control catego- The internal circuits of the SRB Structure of a safety circuit
Safety related parts shall be designed so that: Faults will be detected in time to prevent
1. a single fault in any of these parts does not lead to the loss the loss of the safety function.
of the safety function,
2. the single fault is detected at or before the next demand
on the safety function or, if this is not possible, an accu-
mulation of faults shall not lead to a loss of safety functions.
161
Scope of products (continued)
162
Input circuitry Input circuits as proposed below are
sufficient in standard situations:
Control category 1:
single channel input without initial
start test.
Control category 2:
Single channel input with initial start
test.
Control category 3:
Dual channel input without initial
start test.
Control category 4:
Dual channel input with initial start
test. ▲ Examples of SRB modules with option "Initial start test"
A dual channel safety circuit is not
necessarily the answer to the
question if a moveable protective Initial start test means the complete contact safety devices (i.e. light
gate needs to be monitored by one or safety circuit needs to perform a test curtains) relay circuits may be
by two Safety Limit Switches. This run on power up prior to be set into needed to perform such a test
is to be found either in the corre- the determined function in order to independently from intention. This
sponding product standards (C- detect possible hidden defects. means in the case of a door inter-
standards) or is resulting of a risk locking that the protective door must
If such an initial start test is not part be opened and closed to initialize
assessment as per EN 1050. of the safety device itself like in non the safety circuit, proper result
provided.
Enabling Enabling
Open output
output
Open
S1
Protective guard
Protective S1
guard
K1
K1
S2
S2
Closed
Closed
K2 K2 K1
K2
K2 K1 K1 K2 K3 K2 K3 K1 K2 K1 K3
K3
K1 K2 K1 K2 K3
e.g. Safety
e.g. Safety relay module
relay module
▲ Example of graded protective measures, Category 3 ▲ Example of graded protective measures, Category 4
Execution: Execution:
1. Two contacts of which at least one contact is positive opening 1. Requirements of Category 3
2. Enclosure for contactor/relay to IP 54 2. Wiring of protective devices in separate jacketed cables or
3. Jacketed cables conforming to relevant standards sequentially with short and cross detection or "special shielded
4. Contactor/relay coils with common connection to ground of cable"
control current circuit. 3. Initial start test
163
Scope of products (continued)
164
"Reset button" : The purpose of using a reset button with trailing edge function (slope monitoring accessible chambers in
Automatic or start button in the input circuitry detection) to prevent unexpected machines and in manufacturing
restart of a relay circuit is under safety restart in case of a faulty start systems. In some cases it is even
aspects persuading the operator to button. required by regulations i.e. when
observe a danger free restart. A using safety mats or optical safety
typical example are E-stop circuits. Trailing edge function means the devices. It must be ensured if a
Any restart needs always a separate relay circuit does not process the regulation requires a trailing edge
Reset button. rising slope from an operated start function resp. a slope detection, the
button, but the trailing slope after involved control part is carried out
Sometimes optional, sometimes it is releasing the button. in fail safe technique, too.
mandatory to provide a dynamic
Start signal from the Start button Signal processing based on trailing
edge function is recommended when
Output circuitry SRB modules are available with 2 Stop category 0 or to Stop category In Stop category 1 (= controlled
and with 3 enabling outputs (plus 1 (see EN 60 204-1 : 1998-11, Part stopping) the enabling outputs will
feedback contact) for standard 9.5.4). drop out time delayed. Purpose is to
applications and for more complex maintain the power supply to the
applications with 4 or 5 enabling In Stop category 0 (= uncontrolled motors etc. to complete a controlled
outputs (plus feedback contact). stopping) the enabling outputs will stop. After run out of delay time the
Furthermore the enabling outputs drop out immediately in order to power will then be cut off.
can be selected in correspondence to interrupt the power supply for the
motors etc. as quickly as possible.
Time delayed An immediate shut down of the • Drop out delay time is either fix • If convenient and adequate in
enabling out- power supply to the motors of or is preset in the factory respect to the process the set
puts hazardous motions etc. does not according to customers request delay time may be reduced by an
always lead to the endeavored quick and/or adjusted on site by the external control signal given to a
stop. user. separate input terminal.
A typical example are motors which
can be slowed down to stand still by
generatoric brake mode more rapidly
rather than by immediate shut down
of the energy. In this case drift to
stand still will take more time and is
therefore more dangerous. Time
delayed enabling outputs are also
taking care that fuses in intermediate
circuits of closed loop drives and
also the drives itself are not being
destroyed.
The delayed shut down of energy,
adapted to the maximum breaking
time of the drive serves as a
protection in the case of failure and
protects against unintended restart.
Depending on the application SRB ▲ Examples of SRB modules with time delayed enabling outputs
modules with time delayed enabling
outputs – some up to 30 seconds –
are available.
165
Scope of products (continued)
166
Another good opportunity to A sophisticated combination of
perform dual channel on the power positively guided contacts ensures
side without doubling contactors is maximum only one safety contact
to include the enabling input of the could be affected in case of failure.
closed loop regulator as a second For SUVA dual channel outputs on
channel in the shut down system of a the power side are essential.
dangerous motion (see fig.).
This would also avoid dangerous
situations at the power side caused
by a welded contact of the contactor.
In this case the interrupted enabling
input would stop the dangerous
motion or vice versa.
Should the enabling of the regulator
not work properly it can be assumed
the contactor works correctly and
brings the dangerous motion to stop. In case of dual channel control on
the power level the use of SRB
If the regulator provides also a
modules providing SUVA circuitry
feedback signal an error detection is recommended. The term SUVA
also of this channel is possible. circuitry is rooted back to require-
In practice after a given Stop signal ments from the Swiss occupational
the enabling input of the regulator safety organization SUVA. This
circuit is covering also the simulta- ▲ Examples of SRB modules with
would interrupt at once and the SUVA circuitry
contactor K1 after the preset slow neous welding of contacts in the
down time of the motor. channel relays.
Fuses Generally all SRB modules are On request the outputs are provided In the SRB module C.17 a special
equipped with internal fuses (glass with an automatic unlatched short electronic overload protection is
tube type). In 45 mm wide modules circuit protection. Please note: In performed. In case of overload reset
– excluding exceptions – for free application without Reset button an is achieved by power down followed
access an additional second fuse unintentional restart is to be by power up. So no exchange of
with lower rated current is located expected. The consideration of this blown fuses is necessary and on the
on the front lid for a simplified fuse warning is on the users side. other hand the danger of unintended
exchange. Otherwise it is recom- restart is eliminated.
mended to furnish an additional fuse
with lower rated current in the
power supply circuit.
167
Notes
168
Sales organisation
Europe Overseas
Austria Australia
Belgium Brazil
Czech Republic Canada
Denmark Chile
Finland China
France Hong Kong
Hungary India
Iceland Israel
Italy Japan
Luxembourg Malaysia
Norway Singapore
Poland Taiwan
Portugal USA
Slovakia
Slovenia
Spain
Sweden
Switzerland
United Kingdom