Tools to be prepared
1.Disassembly and assembly flow chart of left front
door.the other three doors are the same
Step 1: remove the T30 screw
here
Pa eT faa se |
Step 2: remove the T30 screw | Step 3: the rotation here is up and
here
2. Remove the door panel
down
(1)Pry off the armrest
cover
(2)Use T30 to remove the
screws
(3)Use T30 to screw the
buckle
position
internal into a
vertical and
release it to the rear door
panel
Oa
é
(4)Buckle the handle clip
by hand
3. Front door panel trim lamp installation
—
(1)Original front door
monochrome plug
(2)Expand the position of the
monochrome lamp cap on the front
door of the original car
£
(3)Remove the monochrome lamp cap
from the front door of the original car
(4)Put our multicolor lamp
caps in the front door
4. Installation of front door
handle lamp
(The front door of the original car is equipped with a handle lamp as standard, and
there is no handle lamp at the back. If necessary, it can be perforated or not
installed)
wn SL Al
|
(2)Place the multi-color lamp panel in
the original lamp housing
(3)The multi-color light plate is fixed
with the handle light
5. Installation of door pane
(The front door of the original vehicle is
and this step can be ignored for the lamp
ay.
| handle lamp
equipped with armrest lamp as standard,
of product 17)
()Remove the original handrail lamp
board and aim the lamp beads of our
lamp board at the acrylic illuminant
(2)Fix the lamp plate and the base of the
lamp shell together with adhesive tape,
and the lamp beads must be aligned
with the luminous body
(B)After the armrest lamp is fixed, reset
it
(4)There is no monochrome in the
original car of the rear door. It can also
be installed with holes to expose the
lamp beads
6. Front and rear door panel storage lamp installation
(2)Opening diagram of door
panel storage box
7. Installation of rear door trim lamp strip
Ly
(1)Grind off the spot of the
original rear door
(2)After the trim panel is
removed
(3)Remove the original
rear door plating strip first
(4)Install the plated
winding strip on the
product head
8. Rear door light strip opening
(1)Opening position of rear door
(2)Opening position of rear door
(3) Make a small hole in
passes through here
the back door. The light bar
9. Front door panel power cord adapter plug
The service life of the door panel modi
into horizontal needle and vertical need!
directly )
lule adapter plug is different. It is divided
le. If it is not suitable, it can be spliced
(2) Press and hold the clip inside the
red clip and pull it out
(3) Pull the latch from the side to
separate and take out the plug
(4) Insert the plug of the original
vehicle into our adapter plug
(5) Insert the adapter plug into the
original vehicle module
(6) The power cord of the original
vehicle is connected with our adapter
plug
10. Installation of rear door power transfer plug
(2) Plug the plug of the original car
ordering machine and the break free
line adapter plug into each other
(3) After switching, plug it back into
the original elevator motor slot
11. CAN line transfer behin
of atmosphere lamp
id the central control screen
(The color of the original can line is different from that of individual models. First
transfer one orange brown line, and then transfer another one)
”
-
line. Take out the original vehicle can line
(1) Holes 6-12 of the gray plug of the original vehicle are the original vehicle can
and insert our adapter line
(2) Be sure to take out one and insert
another. The hole position cannot be
reversed
(3) Effect of transfer completion
12. Atmosphere lamp _ int
methods
erface and three control
(The module defaults to ambient lighting. If the other two control modes are
required, it needs to be unplugged)
(1) M8 platform 30 color interface,
automatic switching
the last gear yellow is breathing mode,
Ces iy
ERAN
(2) For Volkswagen models before 18
years, the BCM does not support
brushing ambient lighting. It can be
controlled by footstep lighting. Every
10% increase is a fixed color. The first
gear display on the interface is tuned
off as breathing mode. The specific code
dialing is subject to the module
(3) If you need the mirror knob to
control, the can line must be connected
to the BCM. If the can line is connected
to the rear of the central control screen,
the mirror button cannot be controlled.
The specific code dialing shall be subject
to the module
13. Three code pulling m
Module
Cif the module needs to dial, disconne:
after dialing)
odes of atmosphere lamp
ct the module power plug and plug it in
(4) If you need to dial the code, please
open the upper cover of the main
module
(2) 1. The on direction is controlled
the ambient lighting color list
(3) 1.2.3.4, Lighting control for door
and footwell in off direction
(4) 2. The on direction is controlled by
the rearview mirror adjustment button
14. BCM twisted pair can line transfer flow chart
(The MQB must be connected to the BCM when controlling the rear-view mirror
knob on the platform, and other control modes can be connected to the rear of the
central control screen)
7
(4) The BCM is above the master driver
rest pedal
(2) BCM has three plugs
Unplug the plug at th
(4)Gently pull the latch on both sides of
the plug and slide the housing down and
ie
(5) The original vehicle No. 16.17 has
‘two orange twisted pairs
(6) Take out the twisted pair of the
original vehicle and transfer it to our
break free plug