Professional Documents
Culture Documents
Manual de Alicate Wago
Manual de Alicate Wago
Quickstrip Vario
Operating Instructions
Stripping Tool
Stripping standard cables ranging from 0.03 to 16.0 mm²
Cutting solid cables up to 10 mm² | solid conductors up to 1.5 mm²
2 Accessories Overview
Accessories Item No.
Standard blade set, 0.03 … 16.0 mm² (included)
206-1126
3 Intended Use
The Quickstrip Vario Wire Stripper can be used NOTICE
to reliably strip standard cables ranging from The cable must be stripped to the correct
0.03 to 16.0 mm². length for a correct crimping result. Please
observe the contact material specifications!
2
4 Function Overview
1. L
ug
2. S
AFELINE (safe storage)
5. C
utting function
3
5 Cutting Function
NOTE NOTICE
The tool can be used to cut solid cables up to 10 Before cutting, make sure that the cable has
mm² and solid conductors up to 1.5 mm². been disconnected from the power supply!
5.3 O
pen the tool.
NOTE
Hand protection closes automatically during
each stripping operation.
4
6 Stripping
NOTE NOTICE
By moving the “POWERPLUS” slider into the The partial stripping adjuster must be in the
plus (+) or minus (–) range, the tool can be maximum plus (+) position in order to fully strip
adjusted to different cable types and insula- the insulation. Before stripping, make sure that
tion thicknesses. The tool is factory set and the cable has been disconnected from the
delivered with POWERPLUS in center position, power supply!
allowing all standard cables to be stripped.
5
6.1 C
ompress the length locator and move it to the 6.2 I nsert the conductor into the length locator until it
required stripping length. stops.
6.3 C
lose the tool until the jaws release. 6.4 R
emove the correctly stripped conductor.
7 Partial Stripping
The tool is equipped with a partial stripping unit.
Partial stripping allows the conductor strands to
be protected until the next work step, because
the stripping residue remains on the conductor.
6
NOTE NOTICE
By moving the partial stripping adjuster into The partial stripping adjuster must be in minus
the plus (+) or minus (–) range, the length of the (-) position in order to partially strip the insula-
partial stripping is set (minus (-) = short | plus tion. Before partial stripping, make sure that the
(+) = long). The tool is factory set and delivered cable has been disconnected from the power
with the adjuster in minus (-) position. supply!
7
8 Blade Replacement
INFORMATION
The replacement aid for easy blade exchange
is supplied with the spare blade set. The
basic tool comes without replacement aid
and spare blade set.
8
NOTICE
Do not touch the cutting edge when replacing
the blades. Risk of injury!
8.1 I nsert the replacement aid into the recess below 8.2 C
ompress handles to the stop and hold in position.
the lower blade (arrow on the underside of the
replacement aid/raised portion toward the handles)
as shown in the picture.
8.3 P
ush the blade out of the groove and remove it. 8.4 I nsert the new blades accordingly.
Repeat the same procedure for the upper blade.
9
9 Locking the Tool
9.1 P
ush down the locking device by pulling the tab and 9.2 T
he tool is locked in closed position. Compress the
compress the handels to insert the locking device handles to release the locking function. The locking
into the retaining lug. Engage the locking device on device engages into the upper handle.
the lower handle. The tool remains closed.
INFORMATION
The PUR spring block prevents a jerky move-
ment of the handles during stripping, which
protects both hands and forearms from wear
damage. The PUR spring block is a single
component that can be removed or mounted
as follows:
10.1 R
emove the PUR spring block using a screwdriver. 10.2 T
he PUR spring block has been removed.
10.3 P
ut the PUR spring block back into place in the
reverse order of removal.
10
Notes
11
MM-4738 - 04/2021-00 - Printed in Germany - Subject to changes