Professional Documents
Culture Documents
E2050t en
E2050t en
Website:http://biz.LGservice.com
E-mail:http://www.LGEservice.com/techsup.html
COLOR MONITOR
SERVICE MANUAL
CHASSIS NO. : LM99B
MODEL: E2050T(E2050T-PFV.A***AVN)
( ) **Same model for Service
CAUTION
BEFORE SERVICING THE UNIT,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CONTENTS
SPECIFICATIONS ................................................... 2 ADJUSTMENT ...................................................... 13
PRECAUTIONS ....................................................... 4 TROUBLESHOOTING GUIDE .............................. 15
TIMING CHART ....................................................... 8
EXPLODED VIEW...................................................19
DISASSEMBLY ........................................................ 9
BLOCK DIAGRAM ................................................. 10 SCHEMATIC DIAGRAM ..........................................20
DESCRIPTION OF BLOCK DIAGRAM...................11
SPECIFICATIONS
1. LCD CHARACTERISTICS 4. MAX. RESOLUTION
Type : TFT Color LCD Module Analog : 1600 x 900@60Hz
Active Display Area : 20.0 inch diagonal Digital : 1600 x 900@60Hz
Pixel Pitch : 0.2766(H) x 0.2766 (V)mm
Size : 462.8(H) x 272.0(V) x 11.5(D)mm 5. POWER SUPPLY
Color Depth : 16.7M colors 5-1. Power Adaptor(Built-in Power)
Electrical Interface : LVDS Input : AC 100-240V~, 50/60Hz, 1.0A
Surface Treatment : AG(Haze 25%), Hard Coating(3H)
Operating Mode : Normally White 5-2. Power Consumption
Backlight Unit: W-LED
MODE H/V SYNC VIDEO POWER CONSUMPTION LED COLOR
2. OPTICAL CHARACTERISTICS less than 23 W(max)
2-1. Viewing Angle by Contrast Ratio ≥5 POWER ON (NORMAL) ON/ON ACTIVE PURPLE
less than 21 W(typ)
Left : +75° min., +88°(Typ) Right : -75° min., -88°(Typ) STAND BY OFF/ON OFF less than 1 W PURPLE BLINKING
Top : +70° min., +85°(Typ) Bottom : -70° min., -85°(Typ)
SUSPEND ON/OFF OFF less than 1 W PURPLE BLINKING
2-2. Luminance : 180(Typ) (Typ. 30)-sRGB DPMS OFF OFF/OFF OFF less than 1 W PURPLE BLINKING
AC Volt-meter
TAKE CARE DURING HANDLING THE LCD MODULE
WITH BACKLIGHT UNIT.
• Must mount the module using mounting holes arranged
in four corners. Good Earth Ground
such as WATER PIPE,
• Do not press on the panel, edge of the frame strongly CONDUIT etc.
To Instrument's
or electric shock as this will result in damage to the exposed
screen. METALLIC PARTS
CAUTION
Please use only a plastic screwdriver to protect yourself
from shock hazard during service operation.
Video
B
C
Sync
D E F
A
#1 #2
#1 #2
#3 #4
Copyright 2007 LG Electronics. Inc. All right reserved. -9- LGE Internal Use Only
Only for training and service purposes
DISASSEMBLY-Set
#1 #2
#1 #2
Copyright 2007 LG Electronics. Inc. All right reserved. -9- LGE Internal Use Only
Only for training and service purposes
ADC
Analog (R/G/B) Scaler LVDS TX
D-SUB
Panel
14.318MHz
- 10 -
Crystal
Flash ROM EEPROM
3.3V
BLOCK DIAGRAM
system
3.3V ready
DC/DC 5V
Regulator 1.8V
12V converter
3.3V
Adapter
LED Driver Panel LED string
2. Power Part.
This part consists of the one DC-DC converter to convert power which is provided 12V from Adapter.
12V is provided for LED Driver IC, 5V is provided for LCD panel and micom in E2050T case .
Also, 5V is converted 3.3V and 1.8V by dual channel regulator. Converted power is provided for IC in the main board.
The inverter the 12V provided from LED Driver IC converts from DC 12V to DC 46V and operates back-light LED
of module in E2050T case.
3. MICOM Part.
This part consists of EEPROM IC which stores control data, Reset IC and the Micom.
The Micom distinguishes polarity and frequency of the H/V sync are supplied from signal cable.
The controlled data of each modes is stored in flash memory.
50 ~ 60Hz
67KHz
EMI INPUT RECTIFIER HVDC ENERGY OUTPUT RECTIFIER Vo
COMPONENTS AND FILTER TRANSFER AND FILTER
LINE GND
100 ~ 240V
PHOTO- SIGNAL
PWM
COUPLER Collection-
CONTROL
CIRCUIT ISOLATION ION
PRIMARY SECONDARY
Operation description_Power
1. EMI components.
This part contains of EMI components to comply with global marketing EMI standards like FCC,VCCI CISPR, the
circuit included a line-filter, across line capacitor and of course the primary protection fuse.
3. Energy Transfer.
This part function is for transfer the primary energy to secondary through a power transformer.
5. Photo-Coupler isolation.
This part function is to feed back the DC output changing status through a photo transistor to primary controller to
achieve the stabilized DC output voltage.
6. Signal collection.
This part function is to collect the any change from the DC output and feed back to the primary through photo
transistor.
1. Port Setup
a) Copy “UserPort.sys” file to
“c:\WINNT\system32\drivers” folder
b) Run Userport.exe
2) Wait for about 5 seconds and press MENU, POWER switch for 1 second interval.
3) The SVC OSD menu contains additional menus that the User OSD menu as described below.
IBM 9 6
Video Signal 5 1
Compatible PC 15 11
Generator 10 6
5 1
C
PARALLEL PORT
d
13
se
1
tu
2C
25
No
14
23
RS
OFF ON
5V
EL
Control Line
F
LL
C
RA
PA
VG ON
WE
S 5V
(110V/220V)
PO
E 74LS06
A
T
MO Power LED
CS
NI OFF 4.7K
YN
TO
V-S
R
74LS06
E ST Switch
B
B
F V-Sync On/Off Switch
(Switch must be ON.)
NO POWER
(POWER INDICATOR OFF)
YES
YES
CHECK IC502 NO
4
1 CHECK IC502 PIN2(5V)
PIN1(3.3V),PIN3(1.8V)
YES
CHECK IC501 NO
CHECK CRYSTAL(X500)
PIN127
YES
CHECK IC500
Waveforms
1 IC600-#1 2 IC502-#3 3 IC502-#1 4 IC501-#127
NO RASTER
(OSD IS NOT DISPLAYED)
CHECK IC600 NO
CHECK ADAPTER
1 VOLTAGE PIN1
(12V)?
YES
NO CHECK IC700,IC500,IC502
P701 PIN3,4(about 45V)
YES
Waveforms
1 IC600-#1 2 P701-#3,4
NO RASTER
(OSD IS NOT DISPLAYED)
YES
YES
CHECK IC500
PIN41(H-SYNC) AND NO CHECK CONNECTION LINE
PIN42(V-SYNC). FROM D-SUB TO IC500
IS PULSE APPEARED AT
SIGNAL PINS?
YES
TROUBLE IN CABLE
OR LCD MODULE
Waveforms
4 IC500
TROUBLE IN DPM
YES
1 CHECK NO
IC500 PIN41,42 CHECK H/V SYNC LINE
2 SYNC PULSE
YES
TROUBLE IN IC101
Waveforms
1 H-SYNC 2 V-SYNC
30P
6P
200
410
420
900
430
310
920
JAN.. 2010
P/NO : MFL59082044 Printed in China