Professional Documents
Culture Documents
Controllogix DC (10-31.2V) Electronically Fused Output Module
Controllogix DC (10-31.2V) Electronically Fused Output Module
Identifies information that is critical for successful application and understanding of the
IMPORTANT
product.
ATTENTION Identifies information about practices or circumstances that can lead to personal injury or
death, property damage, or economic loss. Attentions help you:
• identify a hazard
• avoid a hazard
• recognize the consequence
SHOCK HAZARD Labels may be located on or inside the equipment (e.g., drive or motor) to alert people
that dangerous voltage may be present.
BURN HAZARD Labels may be located on or inside the equipment (e.g., drive or motor) to alert people
that surfaces may be dangerous temperatures.
NOTE: See NEMA Standards publication 250 and IEC publication 60529, as applicable,
for explanations of the degrees of protection provided by different types of enclosure.
Also, see the appropriate sections in this publication, as well as the Allen-Bradley
publication 1770-4.1 ("Industrial Automation Wiring and Grounding Guidelines"), for
additional installation requirements pertaining to this equipment.
(1)
The ControlLogix system has been agency certified using only the ControlLogix RTBs (i.e. 1756-TBCH,
1756-TBNH 1756-TBSH and 1756-TBS6H). Any application that requires agency certification of the
ControlLogix system using other wiring termination methods may require application specific approval
by the certifying agency.
1. Align the circuit board with the top and bottom chassis guides.
Printed
Circuit
Board
20861–M
2. Slide the module into chassis until module locking tabs click.
Locking tab
U-shaped
bands
20850–M
Wedge-shaped tab
20851–M
20863–M 42516
You can only connect wiring to your module with an RTB or IFM.
2 1
OUT-1 OUT-0
4 3
OUT-9 OUT-8
14 13
OUT-11 OUT-10
16 15
OUT-13 OUT-12
Group 1 18 17 Group 1
OUT-15 OUT-14
20 19
+ –
DC COM 40174-M
NOTES:
1. When you daisy chain from a group to another RTB, always connect the daisy chain
as shown above. Do not connect more than 2 wires to any single terminal.
2. This wiring example shows a single voltage source.
3. If separate power sources are used, do not exceed the specified isolation voltage.
After completing field-side wiring, secure the wires in the strain relief
area with a cable-tie.
Publication 1756-IN030E-EN-P - October 2004
12 ControlLogix DC (10-31.2V) Electronically Fused Output Module
Groove
Side edge of the RTB
Groove
Strain relief area
1. Align the side and top, bottom guides. 2. Press quickly and evenly to seat the RTB
until the latches snap into place.
Locking tab
Module
guide
20853–M 20854–M
RTB guides
3. Slide the locking tab down.
DC OUTPUT
ST 0 1 2 3 4 5 6 7
FUSE O
K
ST 8 9 10 11 12 13 14 15
FUSE
ELECTRONICALLY FUSED 40464-M
During power up, an indicator test is done and the following occurs:
• "OK" indicator turns red for 1 second and then turns to
flashing green if it has passed the self-test.
• I/O status indicators turn ON for a maximum of 2 seconds and
then turn OFF.Fuse status indicators turn ON for 1 second and
then turn OFF.
1. Unlock the locking tab at 2. Open the RTB door and pull
the top of the module. the RTB off the module.
42517 20855–M
20856–M 20857–M
1756-OB16E Specifications
Configurable States in Program Hold Last State, ON or OFF (OFF is the default)
Mode per Point
Fusing Electronically fused per group
Reverse Polarity Protection None - If module is wired incorrectly, outputs may be
damaged.
Isolation Voltage
Group to group 250V continuous
Tested to 1900V dc for 60 seconds
User to system 250V continuous
Tested to 3250V dc for 60 seconds
RTB Screw Torque (NEMA) 7-9 inch-pounds (0.8-1Nm)
Module Keying (Backplane) Software configurable
RTB Keying User defined mechanical keying
RTB and Housing 20 Position RTB (1756-TBNH or TBSH)(2)
Conductors
Wire Size #22 to #14 AWG (0.324 to 2.08 sq. mm)(2)
3/64 inch (1.2mm) insulation maximum
Wire Type Copper
Category 1(3), (4)
Screwdriver Blade Width for RTB 5/16 inch (8mm) maximum
Environmental Conditions
Operating Temperature IEC 60068-2-1 (Test Ad, Operating Cold),
IEC 60068-2-2 (Test Bd, Operating Dry Heat),
IEC 60068-2-14 (Test Nb, Operating Thermal Shock):
0 to 60°C (32 to 140°F)
Storage Temperature IEC 60068-2-1 (Test Ab, Un-packaged Non-operating
Cold),
IEC 60068-2-2 (Test Bb, Un-packaged Non-operating
Dry Heat),
IEC 60068-2-14 (Test Na, Un-packaged Non-operating
Thermal Shock):
–40 to 85°C (–40 to 185°F)
Installation Assistance
If you experience a problem with a hardware module within the first 24 hours
of installation, please review the information that's contained in this manual.
You can also contact a special Customer Support number for initial help in
getting your module up and running:
United States 1.440.646.3223 Monday – Friday, 8am – 5pm EST
Outside United States Please contact your local Rockwell Automation representative for
any technical support issues.