Professional Documents
Culture Documents
Inhalt
Edition 10.2008
Product Information – Door closers
Inhalt
According to the liability of manufacturers for their products as – when someone grasps between frame and door leaf (danger of
defined in the German „Law of Product Liability“ (§4 ProdHaftG), the injury)
following information on door closers and floor springs for side hung – when beyond the qualities confirmed by the manufacturer correct
doors must be considered. functioning is expected under extreme conditions such as storm
Non-observance by customers releases the manufacturer from his or extraordinary high or low pressure acting on the door
product liablility. – when door closers or floor springs not tested to DIN are used on
fire rated doors
1. Product information and application in accordance with the
directives 3. Liability
Door closers and floor springs are designed to close side hung doors The respective entire hardware set may only consist of G.U/BKS
after their manual opening. hardware components. In the case of inappropriately assembled
The closing is hydraulically damped, the closing speed is adjustable. hardware, and/or in case of non original accessory components
The required latching force depends on the sash widths and weights and/or non factory-approved accessory components, no liability is
and is determined by EN 1154. accepted.
In the case of door closers and floor springs not standardized and/or For professional assembly G.U/BKS working drawings and mounting
applications other than defined, the specifications of the manufactu- instructions are to be consulted.
rer are to be considered.
Door closers and floor springs are applied on installed side hung 4. Product specification
doors of metal, timber, PVC, glass or combinations of these materi- Unless described in detail in catalogues, brochures, instructions etc.,
als. special product specifications must be discussed with the manufac-
For smoke and fire rated doors type of mounting and position are turer and approved by him.
exactly prescribed. Any deviation in application is not in accordance The following standards apply:
with the directives. DIN 18 263 part 1and EN 1154 „Door closers with hydraulic
The application of door closers and floor springs in accordance with damping“. EN 1155 „Hold-open devices“ and EN 1158 „Door leaf
the directives requires perpendicularly installed and smooth-running coordinators“.
doors with correctly mounted door closers or floor springs. Their
mounting and adjustment must be carried out expertly following the 5. Maintenance and care
instructions of the manufacturer. Components of door closers and floor springs relevant to security
With unfavourable local conditions (e.g. effect of wind), door closers must be regularly checked for tight fit and wear. Fixing screws must
with a high closing force must be used. Especially on side hung be tightened up, defect parts must be exchanged. Moreover, the fol-
doors opening outwards, door closers with backcheck should be lowing works have to be carried out at least once a year depending
used. Without limiting the opening angle of the door, back check on type and purpose of the side hung door:
provides for the protection of persons, door components, adjacent – All moving parts must be greased.
walls and objects. – The settings of the door closer (e.g. closing speed) must be che-
A fixed open position of side hung doors can only be achieved with cked.
additional fittings or with integrated constructional components. For – The door must be checked for smooth running.
fire rated doors, facilities must be licenced by the German Institute – Door closers with special functions (hold-open devices, hold-open
of Building Technology (the proof suitability of the door must be systems) all legal controls and maintenance procedures must be
considered). carried out.
For damp rooms, for unprotected external mounting and for the use – Door closers and/or defective components must be replaced
in an environment with aggressive air components causing corrosi- immediately, if their correct function is no longer provided.
on, as well as for doors exposed to extremely high or low temperatu- – For maintenance works only lubricants and cleaning detergents
res, door closers in special design are required. must be used which do not contain corrosive or destructive com-
Floor boxes for floor springs must be protected against soiling. If ponents.
floor springs are exposed to ingress of water, e.g. in damp rooms
or on entrance doors without protection against rain, the space 6. Duty to inform and to instruct
between the floor box and floor spring body must be filled with a In order to comply with the duty to inform and to instruct, planners,
suitable sealing compound. special trade, manufacturers, builders and users may consult the
Before installing and operating door closers and floor springs following material:
including additional equipment, it is necessary to observe prevailing – Catalogues, brochures
national or regional directives. – Specification clauses, quotation documents
– Mounting instructions, installation drawings, instructions for use
2. Misuse – EN 1154 (exclusive distribution by Beuth-Verlag GmbH, Berlin)
Misuse – that is the application of door closers for side hung doors – Consulting field service
not in accordance with the directives – exists,
– when door closers and floor springs are used for another purpose For the correct use, the reliable function and the maintenance and
than closing doors care of door closers and floor springs on side hung doors it is neces-
– when the size of the door closer chosen does not correspond to sary that
the recommendations of the manufacturer – architects and planners should obtain and observe the required
– when mounting and/or adjusting were effected incorrectly or product information.
inexpertly – authorized dealers should observe product information and indi-
– when obstacles in the closing area interfere with the closing cations in price lists, and above all order all instructions and pass
– when door hinges interfere with the closing because they are not them on to the installers.
aligned or running smoothly – installers should obtain all product information, special instruc-
– when the door leaf touches the floor tions for use and maintenance and pass them on to customers
– when the door is stuck in the frame and users.
– when closing is obstructed by gaskets, wedges etc. The user must be informed of acceptance tests for hold-open de-
vices or hold-open systems prescribed by the law.
Contents
Inhalt
Product information
Product information according to ProdHaftG 2
Product overview 4
3
Product overview
Inhalt
Crank gear
Closer variant Overhead door closers with scissor action arm
closer
OTS 530
Type OTS 530 OTS 440 OTS 430 OTS 330 OTS 210 OTS 200 OTS 140 OTS 81 OTS 80
EN 4 – 7
Page 16 16 17 19 20 21 22 24 25 26
Application
1-leaf
Usable with smoke and fire doors F F F F [4]
Maximum door leaf width 1-leaf (mm) 1400 1600 1250 1250 1100 1100 1100 1100 1280 1600
Adjustment functions
Closing force sizes according to EN 1154 2-6 4-7 2-5 2-5 2/3/4 2/3/4 3/4 2/3/4 2-5 [4] 2-6 [4]
Closing speed
Latching force
Delayed action
Backcheck optional
Hold-open variants
Electromechanical hold-open device optional [2] optional [2] optional [2] optional [2]
[1]
Mechanical hold-open device (on/off switchable) optional optional optional optional optional optional optional optional optional optional
Hold-open force adjustable
(only with mechanical hold-open)
Hold-open angle between approx. 75° and 150° up to 150°
Maximum door opening and closing angle 180° [5] 180° [5] 180° [5] 180° [5] 180° [5] 180° [5] 180° [5] 180° [5] 90° or 180°
Mouting variants
Standard mounting on hinge side
Transom mounting opposite to hinge side
4 [1] Not suitable for smoke and fire doors [2] Only with hold-open magnet [3] Not on/off switchable [4] acc. to DIN 18263, part 1
[5] Standard mounting on hinge side
Product overview
Inhalt
Product characteristics
Tested and quality controlled to EN 1154.
[1]
Closing force sizes infinitely variable 3 – 6.
Stepless valve adjustment for:
– Closing speed
– Latching force
– Backcheck
Each valve has a different colour and can be adjusted at the front.
Plastic valves with optimum thermal characteristics provide con-
sistent closing speed also with changes in temperature.
Protection against forced operation via security valve.
[2]
Max. door opening and closing angle 180°.
Controlled closing from any opening angle.
All fixings concealed.
Range of application The gliding rail is easily assembled by hanging it in the form-
fitting mounting rail.
For timber, glass, PVC, aluminium and steel swing doors. Many closer variants available.
Non-handed (DIN lh and DIN rh usable). Cover comes in various finishes.
For 1-leaf and 2-leaf (OTS 730 SRI) doors. Cover with safety fastener.
For door leaf widths up to 1400 mm. Optional: Adjustable hold-open device for opening angles between
For interior and exterior smoke and fire doors. 70° and 150° with variable hold-open force.
[3]
Standard mounting on hinge side / opposite to hinge side . Optional: OTS 730 SV with delayed closing action.
[3]
Transom mounting hinge side / opposite to hinge side .
16,5
110
32
7,7
5
50 55
06 0672-CPD-0094
4 8 63 1 1 4
EN 1154: 1996 + A1: 2002
without mounting plate with mounting plate
6 [1] acc. to EN 1154 [2] Standard mounting on hinge side [3] Use door stop for max. door opening angle
Overhead door closer OTS 730 FE
Inhalt
Product characteristics
same as with OTS 730; additional features
Tested and quality controlled to the directives for hold-open sys-
tems and approved by the German Institute of Building Technolo-
gy (DIBt) for use with various smoke and fire detection systems.
With electromechanical hold-open device in the gliding rail.
Steplessly adjustable hold-open range between 75° and 150°.
The hold-open device ensures the hold-open position selected
(no fall-back angle) over any period of time.
Technical data:
– Supply voltage: 24 V DC ±15 %
– Current consumption: 0,042 A
– Power input: 1 Watt
– Duty ratio: 100 %
– Voltage standing-wave ratio below 30 %
Range of application
For timber, glass, PVC, aluminium and steel swing doors.
Non-handed (DIN lh and DIN rh usable).
For 1-leaf and 2-leaf (OTS 730 FE-SRI) doors.
For door leaf widths up to 1400 mm.
For interior and exterior smoke and fire doors.
[1]
Standard mounting on hinge side / opposite to hinge side .
[1]
Transom mounting hinge side / opposite to hinge side .
5
55
06 0672-CPD-0096
4 8 63 1 1 4
EN 1155: 1996 + A1: 2002
with mounting plate
Product characteristics
same as with OTS 730; additional features
Tested and quality controlled to the directives for hold-open sy-
stems and approved by the German Institute of Building Technolo-
gy (DIBt) for use with various smoke and fire detection systems.
Suited for all approved smoke and fire doors, provided the appro-
val document allows the use of door closers to EN 1155.
Electromechanical hold-open device integrated in the gliding rail.
With smoke switch control unit BMZ 730 H, with integral power
supply and release device.
Steplessly adjustable hold-open range between 75° and 150°.
The hold-open device ensures the hold-open position selected
(no fall-back angle) over any period of time.
For technical data of power supply and smoke detector see
description of smoke switch control unit BMZ 730 H.
Range of application
For timber, glass, PVC, aluminium and steel swing doors.
DIN lh and DIN rh variant.
For For door leaf widths up to 1400 mm.
Standard mounting on hinge side.
If the OTS 730 FER is used as hold-open system for fire and smoke
23,5
16,5
32
5
55
8
Door leaf coordinator OTS 730 SRI
Inhalt
06 0672-CPD-0098
4 8 63 1 1 4
EN 1158: 1996 + A1: 2002
[1] Standard mounting on hinge side [2] Mounting opposite to hinge side [3] Not suitable for smoke and fire doors 9
[4] Door closer OTS 730 to be ordered separately [5] Use door stop for max. door opening angle
Door leaf coordinator OTS 730 FE-SRI
Inhalt
Electromechanical hold-open device and door leaf coordinator integrated in gliding rail
(FE-SRI) according to EN 1158
For timber, glass, PVC, aluminium and steel double leaf doors. OTS 730 FE-SRI BG [2] [3] silver colour 1 pc. K-14612-00-0-1
Non-handed, assembly on DIN lh or DIN rh active leaf. Hold-open device on both sides dark bronze colour 1 pc. K-14612-00-0-5
with gliding rail white (RAL 9016) 1 pc. K-14612-00-0-7
Application also possible with unequal door leaf widths. TLW 1570-2800 mm
[1]
Total door leaf width (TLW)
– standard 1240 – 2800 mm
– narrow 1030 – 1240 mm
TLW = Hinge centre to hinge centre.
Smallest possible width of single leaf (SLW)
– standard 420 mm
– narrow 385 mm
[4]
Standard mounting on hinge side / opposite to hinge side .
06 0672-CPD-0100
4 8 63 1 1 4
EN 1158: 1996 + A1: 2002
10 [1] Standard mounting on hinge side [2] Mounting opposite to hinge side [3] Door closer OTS 730 ordered separately
[4] Use door stop for max. door opening angle
Door leaf coordinator OTS 730 FER-SRI
Inhalt
Electromechanical hold-open device integrated in the gliding rail. OTS 730 FER-SRI [1] [3] silver colour 1 pc. K-14606-00-0-1
Hold-open system on both leaves dark bronze colour 1 pc. K-14606-00-0-5
Electromechanical hold-open device available for one or both with gliding rail white (RAL 9016) 1 pc. K-14606-00-0-7
door leaves. TLW 1640-2800 mm
With integral smoke switch control unit BMZ 730 H and power OTS 730 FER-SRI BG [2] [3] silver colour 1 pc. K-14613-00-0-1
supply unit. Hold-open system on active leaf dark bronze colour 1 pc. K-14613-00-0-5
with gliding rail white (RAL 9016) 1 pc. K-14613-00-0-7
Steplessly adjustable hold-open range between 75° and 150° on TLW 1960-2800 mm
the active leaf or on both active and inactive leaf. OTS 730 FER-SRI BG [2] [3] silver colour 1 pc. K-14614-00-0-1
The hold-open device ensures the hold-open position selected Hold-open system on both leaves dark bronze colour 1 pc. K-14614-00-0-5
(no fall-back angle) over any period of time. with gliding rail white (RAL 9016) 1 pc. K-14614-00-0-7
TLW 1960-2800 mm
For technical data of power supply and smoke detector see
description of smoke switch control unit BMZ 730 H.
If the OTS 730 FER-SRI is used as hold-open system for fire and
smoke doors, the particular national or regional directives for hold-
Range of application open systems must be observed.
For timber, glass, PVC, aluminium and steel double leaf doors.
Non-handed, assembly on DIN lh or DIN rh active leaf.
Application also possible with unequal door leaf widths.
[1]
Total door leaf width (TLW)
– standard 1640 – 2800 mm
TLW = Hinge centre to hinge centre.
Smallest possible width of single leaf (SLW)
– standard 420 mm
[4]
Standard mounting on hinge side / opposite to hinge side .
06 0672-CPD-0100
4 8 63 1 1 4
EN 1158: 1996 + A1: 2002
[1] Standard mounting on hinge side [2] Mounting opposite to hinge side 11
[3] Door closer OTS 730, smoke switch control unit BMZ 730 H and mounting set to be ordered separately [4] Use door stop for max. door opening angle.
Overhead door closer OTS 634
Inhalt
Product characteristics
Tested to EN 1154.
[1]
Closing force sizes infinitely variable 2 – 4.
Stepless valve adjustment for:
– Closing speed
– Latching force
– Backcheck
Plastic valves with optimum thermal characteristics provide con-
sistent closing speed also with changes in temperature.
Protection against forced operation via security valve.
[2]
Max. door opening and closing angle 180°.
Controlled closing from any opening angle.
Compact and shapely aluminium cover.
Range of application
For timber, PVC, aluminium and steel swing doors.
Non-handed (DIN lh and DIN rh usable).
For door leaf widths up to 1100 mm.
For interior and exterior smoke and fire doors.
Standard mounting on hinge side.
[3]
Transom mounting opposite to hinge side.
97
296
10
10
114,5
114,5
34,5
7,5
5
48 53
08 0432-BPR-0067
4 8 42 1 1 4
EN 1154: 1996 + A1: 2002
without mounting plate with mounting plate
12 [1] acc. to EN 1154 [2] Standard mounting on hinge side [3] Use door stop for max. door opening angle
Overhead door closer OTS 633
Inhalt
Product characteristics
Tested to EN 1154.
[1]
Closing force size 3.
Stepless valve adjustment for:
– Closing speed
– Latching force
Plastic valves with optimum thermal characteristics provide con-
sistent closing speed also with changes in temperature.
Protection against forced operation via security valve.
[2]
Max. door opening and closing angle 180°.
Controlled closing from any opening angle.
Compact and shapely aluminium cover.
Range of application
For timber, PVC, aluminium and steel swing doors.
Non-handed (DIN lh and DIN rh usable).
For For door leaf widths up to 950 mm.
For interior and exterior smoke and fire doors.
Standard mounting on hinge side.
[3]
Transom mounting opposite to hinge side.
75
236
10
10
119
119
36
7,5
5
43,5 48,5
08 0432-BPR-0067
4 8 3 1 1 4
EN 1154: 1996 + A1: 2002
without mounting plate with mounting plate
[1] acc. to EN 1154 [2] Standard mounting on hinge side [3] Use door stop for max. door opening angle 13
Overhead door closer OTS 630
Inhalt
Product characteristics
[1]
Closing force sizes infinitely variable 1 – 4.
Stepless valve adjustment for:
– Closing speed
– Latching force
Each valve has a different colour and can be adjusted at the front.
Plastic valves with optimum thermal characteristics provide con-
sistent closing speed also with changes in temperature.
Protection against forced operation via security valve.
[2]
Max. door opening and closing angle 180°.
Controlled closing from any opening angle.
All fixings concealed.
The gliding rail is easily assembled by hanging it in the form-
fitting mounting rail.
Range of application Cover comes in various finishes.
Cover with safety fastener.
For timber, glass, PVC, aluminium and steel swing doors.
Optional: Adjustable hold-open device for opening angles between
Non-handed (DIN lh and DIN rh usable). 70° and 150° with variable hold-open force.
[4]
For 1-leaf and 2-leaf (e.g. OTS 630 SRI ) doors.
For door leaf widths up to 1100 mm.
[3]
Standard mounting on hinge side / opposite to hinge side .
[3]
Transom mounting hinge side / opposite to hinge side .
16,5
110
110
32
7,7
5
50 55
08 2008-OTS-0002
4 8 41 0 1 4
EN 1154: 1996 + A1: 2002
without mounting plate with mounting plate
14 [1] acc. to EN 1154 [2] Standard mounting on hinge side [3] Use door stop for max. door opening angle [4] OTS 630 combinable with OTS 730 SRI
Overhead door closer OTS 610
Inhalt
Product characteristics
[1]
Closing force sizes infinitely variable 2 – 4.
Stepless valve adjustment for:
– Closing speed
– Latching force
– Backcheck
Plastic valves with optimum thermal characteristics provide con-
sistent closing speed also with changes in temperature.
Protection against forced operation via security valve.
[2]
Max. door opening and closing angle 180°.
Controlled closing from any opening angle.
Compact and shapely aluminium cover.
[4]
Optional: Hold-open device OTS 610.
Range of application
For timber, PVC, aluminium and steel swing doors.
Non-handed (DIN lh and DIN rh usable).
For door leaf widths up to 1100 mm.
Standard mounting on hinge side.
[3]
Transom mounting opposite to hinge side.
mechanical
114,5
114,5
34,5
7,5
5
48 53
08 2008-OTS-0002
4 8 42 0 1 4
EN 1154: 1996 + A1: 2002
without mounting plate with mounting plate
[1] acc. to EN 1154 [2] Standard mounting on hinge side [3] Use door stop for max. door opening angle [4] no opening beyond hold-open angle 15
Overhead door closer OTS 530
Inhalt
Product characteristics
Tested and quality controlled to EN 1154.
[1]
Closing force sizes infinitely variable 2 – 6 ,
adjustment on the side
Stepless valve adjustment for:
– Closing speed
– Latching force
– Delayed closing action
– Backcheck
Each valve has a different colour and can be adjusted at the front.
Plastic valves with optimum thermal characteristics provide con-
sistent closing speed also with changes in temperature.
Protection against forced operation via security valve.
[2]
Max. door opening and closing angle 180°.
Controlled closing from any opening angle.
Range of application Easy mounting of screw-on plate thanks to fully detachable arm.
For timber, glass, PVC, aluminium and steel swing doors. Cover comes in various finishes.
Non-handed (DIN lh and DIN rh usable). Cover with safety fastener.
For For door leaf widths up to 1400 mm. Optional: Adjustable hold-open device for opening angles between
For interior and exterior smoke and fire doors. 70° and 150° with variable hold-open force.
Standard mounting on hinge side. Optional: Extended arm for transom mounting with large soffit
Transom mounting opposite to hinge side.
[3] depths.
Optional: OTS 530 EN 4-7 for For door leaf widths up to 1600
[4]
mm.
7,0
32
7,7
50 5
55
06 0672-CPD-0092
4 8 62 1 1 4
EN 1154: 1996 + A1: 2002
without mounting plate with mounting plate
16 [1] acc. to EN 1154 [2] Standard mounting on hinge side [3] Opening angle depending on door situation
[4] Not suitable for smoke and fire doors
Overhead door closer OTS 440
Inhalt
Product characteristics
[1]
Closing force sizes infinitely variable 2 – 5.
Adjustment on the side, displacement of closer body not required.
Stepless valve adjustment at the front for:
– Closing speed
– Latching force
Plastic valves with optimum thermal characteristics provide con-
sistent closing speed also with changes in temperature.
Protection against forced operation via security valve.
[2]
Max. door opening and closing angle 180°.
Controlled closing from any opening angle.
Compact and shapely aluminium cover.
Optional: Adjustable hold-open device for opening angles between
70° and 150°.
Range of application Optional: OTS 440 BC with backcheck.
7,0
99
36
7,5
5
43,5 48,5
08 2008-OTS-0002
4 8 52 0 1 4
EN 1154: 1996 + A1: 2002
without mounting plate with mounting plate
[1] acc. to EN 1154 [2] Standard mounting on hinge side [3] Opening angle depending on door situation 17
Overhead door closer OTS 440 G
Inhalt
Product characteristics
Stepless valve adjustment at the front for:
– Closing speed
– Latching force
Plastic valves with optimum thermal characteristics provide con-
sistent closing speed also with changes in temperature.
Protection against forced operation via security valve.
[1]
Max. door opening and closing angle 180°.
Controlled closing from any opening angle.
Compact and shapely aluminium cover.
Adjustable hold-open device for opening angles between 70° and
150° with variable hold-open force.
Range of application
For timber, glass, PVC, aluminium and steel swing doors.
Non-handed (DIN lh and DIN rh usable).
For For door leaf widths up to 900 mm.
Standard mounting on hinge side.
[2]
Transom mounting opposite to hinge side.
11,2
104
36
7,5
5
43,5 48,5
08 2008-OTS-0002
18 [1] Standard mounting on hinge side [2] Use door stop for max. door opening angle
Overhead door closer OTS 430
Inhalt
Product characteristics
Tested and quality controlled to EN 1154.
[1]
Closing force sizes infinitely variable 2 – 5.
Adjustment on the side, displacement of closer body not required.
Stepless valve adjustment at the front for
– Closing speed
– Latching force
Plastic valves with optimum thermal characteristics provide con-
sistent closing speed also with changes in temperature.
Protection against forced operation via security valve.
[2]
Max. door opening and closing angle 180°.
Controlled closing from any opening angle.
Compact and shapely aluminium cover.
Range of application
For timber, glass, PVC, aluminium and steel swing doors.
Non-handed (DIN lh and DIN rh usable).
For For door leaf widths up to 1250 mm.
For interior and exterior smoke and fire doors.
Standard mounting on hinge side.
[3]
Transom mounting opposite to hinge side.
236
7,0
7,0
99
36
7,5
5
43,5 48,5
04 0432-BPR-0067
4 8 52 1 1 4
EN 1154: 1996 + A1: 2002
without mounting plate with mounting plate
[1] acc. to EN 1154 [2] Standard mounting on hinge side [3] Opening angle depending on door situation 19
Overhead door closer OTS 330
Inhalt
Product characteristics
Tested and quality controlled to EN 1154.
[1]
Closing force sizes 2 / 3 / 4.
Adjusting is done by displacing the closer body and turning the
arm bearing upside down.
Stepless valve adjustment at the front for
– Closing speed
– Latching force
Plastic valves with optimum thermal characteristics provide con-
sistent closing speed also with changes in temperature.
Protection against forced operation via security valve.
[2]
Max. door opening and closing angle 180°.
Controlled closing from any opening angle.
Compact and shapely aluminium cover.
Range of application
For timber, glass, PVC, aluminium and steel swing doors.
Non-handed (DIN lh and DIN rh usable).
For For door leaf widths up to 1100 mm
For interior and exterior smoke and fire doors.
Standard mounting on hinge side.
[3]
Transom mounting opposite to hinge side.
207
7,0
7,0
99
36
7,5
5
43,5 48,5
04 0432-BPR-0067
4 8 42 1 1 4
EN 1154: 1996 + A1: 2002
without mounting plate with mounting plate
20 [1] acc. to EN 1154 [2] Standard mounting on hinge side [3] Opening angle depending on door situation
Overhead door closer OTS 210
Inhalt
Product characteristics
[1]
Closing force sizes 2 / 3 / 4.
Adjusting is done by displacing the closer body and turning the
arm bearing upside down.
Stepless valve adjustment at the front for
– Closing speed
– Latching force
Plastic valves with optimum thermal characteristics provide con-
sistent closing speed also with changes in temperature.
Protection against forced operation via security valve.
[2]
Max. door opening and closing angle 180°.
Controlled closing from any opening angle.
Compact and shapely aluminium cover.
Optional: Adjustable hold-open device for opening angles between
70° and 150°.
Range of application
Optional: OTS 210 with gliding rail with and without hold-open
For timber, glass, PVC, aluminium and steel swing doors. device.
[4]
Hold-open arm OTS 210 / OTS 440 silver colour 1 pc. K-17456-00-0-1
mechanical dark bronze colour 1 pc. K-17456-00-0-5
207
white (RAL 9016) 1 pc. K-17456-00-0-7
Gliding rail with slide arm [4] silver colour 1 pc. K-17183-02-0-1
dark bronze colour 1 pc. K-17183-02-0-5
white (RAL 9016) 1 pc. K-17183-02-0-7
7,0
7,0
Gliding rail with slide arm [4] silver colour 1 pc. K-17183-01-0-1
and hold-open device dark bronze colour 1 pc. K-17183-01-0-5
white (RAL 9016) 1 pc. K-17183-01-0-7
99
36
7,5
[1] acc. to EN 1154 [2] Standard mounting on hinge side [3] Opening angle depending on door situation [4] maximum door leaf width 850 mm 21
Overhead door closer OTS 200
Inhalt
Product characteristics
[1]
Closing force sizes 3 / 4.
Adjusting is done by displacing the closer body and turning the
arm bearing upside down.
Stepless valve adjustment at the front for
– Closing speed
– Latching force
Plastic valves with optimum thermal characteristics provide con-
sistent closing speed also with changes in temperature.
Protection against forced operation via security valve.
[2]
Max. door opening and closing angle 180°.
Controlled closing from any opening angle.
Compact and shapely aluminium cover.
Optional: with hold-open device for opening angles between 70°
and 150°.
Range of application
For timber, PVC, aluminium and steel swing doors.
Non-handed (DIN lh and DIN rh usable).
For door leaf widths up to 1100 mm.
Standard mounting on hinge side.
[3]
Transom mounting opposite to hinge side.
195
9,0
93
7,0
36
08 2008-OTS-0002
4 8 43 0 1 4
EN 1154: 1996 + A1: 2002
22 [1] acc. to EN 1154 [2] Standard mounting on hinge side [3] Opening angle depending on door situation
Overhead door closer OTS 200 G
Inhalt
Product characteristics
Stepless valve adjustment at the front for
– Closing speed
– Latching force
Plastic valves with optimum thermal characteristics provide con-
sistent closing speed also with changes in temperature.
Protection against forced operation via security valve.
[2]
Max. door opening and closing angle 180°.
Controlled closing from any opening angle.
Compact and shapely aluminium cover.
[4]
Optional: Hold-open device OTS 200 G (80° – 115°).
Range of application
For timber, PVC, aluminium and steel internal swing doors.
Non-handed (DIN lh and DIN rh usable).
For For door leaf widths up to 750 mm.
Standard mounting on hinge side.
[3]
Transom mounting opposite to hinge side.
mechanical
48
195
10
97
7,0
36
08 2008-OTS-0002
[2] Standard mounting on hinge side [3] Use door stop for max. door opening angle [4] no opening beyond hold-open angle 23
Overhead door closer OTS 140
Inhalt
Product characteristics
[1]
Closing force sizes 2 / 3 / 4.
Adjusting is done by displacing the closer body and turning the
arm bearing upside down.
Stepless valve adjustment for:
– Closing speed
– Latching force
Plastic valves with optimum thermal characteristics provide con-
sistent closing speed also with changes in temperature.
Protection against forced operation via security valve.
[2]
Max. door opening and closing angle 180°.
Controlled closing from any opening angle.
Compact and shapely aluminium cover.
Optional: with hold-open device for opening angles between 70°
and 150°.
Range of application
For timber, PVC, aluminium and steel swing doors.
Non-handed (DIN lh and DIN rh usable).
For door leaf widths up to 1100 mm.
Standard mounting on hinge side.
[3]
Transom mounting opposite to hinge side.
221
8,25
105
19,5
43
08 2008-OTS-0002
4 8 42 0 1 4
EN 1154: 1996 + A1: 2002
24 [1] acc. to EN 1154 [2] Standard mounting on hinge side [3] Opening angle depending on door situation
Overhead door closer OTS 81
Inhalt
Product characteristics
Retro door closer with crank drive.
Tested and quality controlled to DIN 18263, part 1.
[1]
Closing force sizes 2 – 5.
Steplessly adjustable closing speed largely independent of tem-
perature.
Latching force adjustable via the linkage.
High efficiency.
Small height of base plate.
[2]
Max. door opening angle 90° or 180° with extended arm.
Controlled closing from an opening angle of 45°.
Optional: With hold-open arm.
Range of application
For timber, PVC, aluminium and steel swing doors.
Non-handed (DIN lh and DIN rh usable) by reversing the spring.
For door leaf widths up to 1280 mm.
Standard mounting on hinge side.
[3]
Transom mounting opposite to hinge side.
20,5
L
16
[1] acc. to DIN 18263, part 1 [2] Standard mounting on hinge side [3] Opening angle depending on door situation 25
Overhead door closer OTS 80
Inhalt
Product characteristics
Retro door closer with crank drive for rustic doors.
[1]
Closing force sizes 2 – 6.
Steplessly adjustable closing speed largely independent of tem-
perature.
Latching force adjustable via the linkage.
High efficiency.
Small height of bearing plate.
Max. door opening angle 90° or 180°:
– opening beyond 110° requires either an extended arm or
[2]
– moving the closer towards the door hinge.
Controlled closing from an opening angle of 45°.
Optional: With hold-open arm for any hold-open angle up to 150°.
Range of application
For timber, PVC, aluminium and steel swing doors.
Non-handed (DIN lh and DIN rh usable) by reversing the spring.
For door leaf widths beyond 1400 mm.
Standard mounting on hinge side.
[3]
Transom mounting opposite to hinge side.
26 [1] acc. to DIN 18263, part 1 [2] Attention: Closing force reduced [3] Opening angle depending on door situation
Rebate door closer 20 and 24
Inhalt
Product characteristics
Concealed installation in the vertical door rebate.
[1]
Closing force adjustable at the front:
– 1 – 2 = Rebate door closer 20
– 2 – 3 = Rebate door closer 24
The appearance of a sophisticated door is not affected by any
fitting parts, the door closer is“invisible“.
Stepless valve adjustment for:
– Closing speed
– Latching force
Each valve has a different colour and can be adjusted at the front.
Plastic valves with optimum thermal characteristics provide con-
sistent closing speed also with changes in temperature.
Protection against forced operation via security valve.
[2] [3]
Max. door opening angle 130°.
Range of application
Controlled closing from an opening angle of approx. 90°.
For interior timber, PVC, aluminium or steel swing doors, flush or High gasket pressure with the door closed.
rebated, not exposed to wind.
Convenient door opening thanks to decreasing resisting force.
Universally usable for all door shapes, especially suited for round,
segmental and lanced arched doors. Compact anodised aluminium case.
Minimum door leaf thickness:
– 30 mm = Rebate door closer 20
– 40 mm = Rebate door closer 24
Non-handed (DIN lh and DIN rh usable).
Maximum door leaf widths:
– 900 = Rebate door closer 20
– 1000 = Rebate door closer 24
7,5
7,0 5,0 Rebate door closer 24 silver colour 1 pc. K-15145-00-0-0
08 2008-FTS-0004
4 8 32 0 1 4
320
400
10
70 19,5 23,5
[1] acc. to EN 1154 [2] Use door stop for max. door opening angle [3] Opening angle depending on installation dimensions 27
Floor spring UTS 85 HF
Inhalt
Product characteristics
[1]
Closing force sizes infinitely variable from above 2 – 6.
Stepless valve adjustment for:
– Closing speed
– Latching force
Easy longitudinal, lateral and vertical adjustment of the closer
body within the cement case allows for problem-free door instal-
lation.
Plastic valves with optimum thermal characteristics provide con-
sistent closing speed also with changes in temperature.
Protection against forced operation via security valve.
Max. door opening angle 180°.
Mechanical backcheck from an opening angle of approx. 80°.
Adjustable delayed action as a standard.
Adjustable, hydraulic hold-open from approx. 80° to 180°.
Range of application
Aluminium body, galvanised cement case protected against
For timber, glass, PVC, aluminium and steel swing and double corrosion.
action swing doors. Removable divided axle with self-centering crown gearing.
Non-handed (DIN lh and DIN rh usable).
For door leaf widths up to 1400 mm.
For door leaf weights up to 300 kg.
51-59
Cover plates
stainless steel 1 pc. K-12928-00-0-8
brass colour matt finish 1 pc. K-12929-00-0-0
aluminium anodised natural colour 1 pc. K-12926-00-0-1
aluminium anodised dark bronze 1 pc. K-12926-00-0-5
60
63
365
08 2008-UTS-0003
4 8 62 0 1 4
EN 1154: 1996 + A1: 2002
Product characteristics
Tested and quality controlled to EN 1154.
[1]
Closing force sizes infinitely variable from above 3 – 6.
Stepless valve adjustment for:
– Closing speed
– Latching force
Easy longitudinal, lateral and vertical adjustment of the closer
body within the cement case allows for problem-free door instal-
lation.
Plastic valves with optimum thermal characteristics provide con-
sistent closing speed also with changes in temperature.
Protection against forced operation via security valve.
Max. door opening and closing angle 180°.
Controlled closing from any opening angle.
Backcheck function from an opening angle of approx. 80°.
Range of application
Aluminium body, galvanised cement case protected against
For timber, glass, PVC, aluminium and steel swing doors. corrosion.
For interior and exterior smoke and fire doors. Removable divided axle with self-centering crown gearing.
DIN lh and DIN rh variant.
For door leaf widths up to 1400 mm.
For door leaf weights up to 300 kg.
63
365
06 0672-CPD-0101
4 8 63 1 1 4
EN 1154: 1996 + A1: 2002
Product characteristics
Tested and quality controlled to the directives for hold-open sy-
stems and approved by the German Institute of Building Technolo-
gy (DIBt) for use with various smoke and fire detection systems.
[1]
Closing force sizes infinitely variable from above 3 – 6.
Hold-open range continuously adjustable from approx. 80° up to
180°.
Easy longitudinal, lateral and vertical adjustment of the closer
body within the cement case allows for problem-free door instal-
lation.
Plastic valves with optimum thermal characteristics provide con-
sistent closing speed also with changes in temperature.
Protection against forced operation via security valve.
Aluminium body, galvanised cement case protected against
corrosion.
Range of application Removable divided axle with self-centering crown gearing.
For timber, glass, PVC, aluminium and steel swing doors. Connecting cable with injection moulded coupling box, with
3,5 m flexible protective tube and waterproof plug connection.
For interior and exterior smoke and fire doors.
Technical data:
DIN lh and DIN rh variant.
– Supply voltage: 24 V DC ±15 %
For door leaf widths up to 1400 mm. – Current consumption: 0,042 A
For door leaf weights up to 300 kg. – Power input: 1 Watt
– Duty ratio: 100 %
– Voltage standing-wave ratio below 30 %
63
365
06 0672-CPD-0102
4 8 63 1 1 4
EN 1155: 1996 + A1: 2002
Product characteristics
Tested and quality controlled to the directives for hold-open sy-
stems and approved by the German Institute of Building Technolo-
gy (DIBt) for use with various smoke and fire detection systems.
With deactivated linkage between door closer mechanism and
door leaf, the door is freely movable both in opening and closing
direction.
[1]
Closing force sizes infinitely variable from above 3 – 6.
Hold-open range continuously adjustable from approx. 80° up to
180°.
Easy longitudinal, lateral and vertical adjustment of the closer
body within the cement case allows for problem-free door instal-
lation.
Plastic valves with optimum thermal characteristics provide con-
sistent closing speed also with changes in temperature.
Range of application Protection against forced operation via security valve.
Aluminium body, galvanised cement case protected against
For timber, glass, PVC, aluminium and steel swing doors. corrosion.
For interior and exterior smoke and fire doors. Removable divided axle with self-centering crown gearing.
DIN lh and DIN rh variant. The operating range of the activated Swing free function reaches
For door leaf widths up to 1400 mm. from 0° to 180°.
For door leaf weights up to 300 kg. Connecting cable with injection moulded coupling box, with
3.5 m flexible protective tube and waterproof plug connection.
Same technical data as of UTS 85 FE
63
365
06 0672-CPD-0102
4 8 63 1 1 4
EN 1155: 1996 + A1: 2002
for UTS 85 F-SRI, UTS 85 FE-SRI and UTS 85 FL-SRI integrated (SRI)
according to EN 1158
51-59
75
342
118
83
63
365
Range of application
For timber, glass, PVC, aluminium and steel double leaf doors.
Application also possible with unequal door leaf widths.
Non-handed (DIN lh and DIN rh usable).
Total door leaf width (TLW)
– standard 1030 – 2800 mm
TLW = Hinge centre to hinge centre.
Smallest possible width of single leaf (SLW)
– standard 420 mm
For door leaf weights up to 300 kg
06 0672-CPD-0103
4 8 63 1 1 4
EN 1158: 1996 + A1: 2002
32
Floor spring UTS 60
Inhalt
Product characteristics
[1]
Closing force size 4.
Stepless valve adjustment for:
– Closing speed
– Latching force
Easy longitudinal, lateral and vertical adjustment of the closer
body within the cement case.
Plastic valves with optimum thermal characteristics provide con-
sistent closing speed also with changes in temperature.
Protection against forced operation via security valve.
Max. door opening angle 180°.
Max. door opening angle at which the door closes by itself: 170°.
Releasable catch for fix hold-open at 90° or 105°.
Mechanical backcheck from an opening angle of approx. 80°.
Range of application Removable divided axle.
Optional: axle extensions by steps of 5 mm.
For timber, glass, PVC, aluminium and steel swing and double
action swing doors. Including stainless steel cover.
Non-handed (DIN lh and DIN rh usable).
For door leaf weights up to 170 kg
For door leaf widths up to 1100 mm
67,5
310
08 2008-UTS-0003
4 8 4 0 1 4
EN 1154: 1996 + A1: 2002
Product characteristics
[1]
Closing force size 3.
Stepless valve adjustment for:
– Closing speed
– Latching force
Easy longitudinal, lateral and vertical adjustment of the closer
body within the cement case.
Plastic valves with optimum thermal characteristics provide con-
sistent closing speed also with changes in temperature.
Protection against forced operation via security valve.
Max. door opening angle 180°.
Max. door opening angle at which the door closes by itself: 170°.
Releasable catch for fix hold-open at 90° or 105°.
Mechanical backcheck from an opening angle of approx. 80°.
Range of application Removable divided axle.
Optional: axle extensions by steps of 5 mm.
For timber, glass, PVC, aluminium and steel swing and double
action swing doors. Including stainless steel cover.
Non-handed (DIN lh and DIN rh usable).
For door leaf weights up to 120 kg
For door leaf widths up to 950 mm
67,5
310
08 2008-UTS-0003
4 8 3 0 1 4
EN 1154: 1996 + A1: 2002
Product characteristics
[1]
Closing force sizes infinitely variable 1 – 4.
Stepless valve adjustment for:
– Closing speed
– Latching force
Easy longitudinal, lateral and vertical adjustment of the closer
body within the cement case.
Plastic valves with optimum thermal characteristics provide con-
sistent closing speed also with changes in temperature.
Protection against forced operation via security valve.
Max. door opening and closing angle 175°.
[2]
Fix hold-open with catch at 90°/ 95°.
Mechanical backcheck from an opening angle of approx. 80°.
Removable divided axle.
Range of application Installation height of 42 mm only.
For timber, glass, PVC, aluminium and steel swing and double
action swing doors.
Non-handed (DIN lh and DIN rh usable).
For door leaf widths up to 1100 mm.
For door leaf weights up to 120 kg.
52
288
08 2008-UTS-0003
4 8 41 0 1 4
EN 1154: 1996 + A1: 2002
[1] acc. to EN 1154 [2] on double action swing doors / swing doors 35
Floor spring UTS 840
Inhalt
Product characteristics
[1]
Closing force size 3 oder 4.
Stepless valve adjustment for:
– Closing speed
– Latching force
Easy longitudinal, lateral and vertical adjustment of the closer
body within the cement case.
Plastic valves with optimum thermal characteristics provide con-
sistent closing speed also with changes in temperature.
Max. door opening and closing angle 130°.
Fix hold-open with catch at 90°.
Mechanical backcheck from an opening angle of approx. 80°.
Removable divided axle.
Installation height only 40 mm.
Range of application
For timber, glass, PVC, aluminium and steel interior and exterior
double action swing doors.
Non-handed (DIN lh and DIN rh usable).
For door leaf weights up to 120 kg.
Cover plates
stainless steel matt finish 1 pc. V-00704-00-0-8H
brass colour 1 pc. V-00704-00-0-3R
63 Sealing compound 1 pc. K-13048-00-0-0
326
1 1
3 2
4
6
Feststellanlagen sind Geräte oder Gerätekombinationen, die ge- 3 Door closer, e.g. OTS 730
eignet sind, die Funktion von Schließmitteln kontrolliert unwirksam 4 Power supply unit NAG 03
zu machen. Beim Ansprechen der zugehörigen Auslösevorrichtung 5 Manual actuation button
im Fall eines Brandes oder bei anderweitiger Auslösung werden
6 Door hold-open magnet
offenstehende Abschlüsse selbsttätig durch die Schließmittel ge-
schlossen.
Components
A hold-open system consists of (at least one each):
fire detector power supply, e.g.
– optical smoke switch for ceiling and wall mounting, – power supply unit NAG 03, NG 519
e.g. ORS 142, ORS 142 W manual actuation button
triggering device, e.g. as interruptor (on-wall or flush mounting)
– smoke switch control unit BMZ 730 H door closer according to EN 1154, e.g.
– power supply unit NAG 03, NG 519 – OTS 730 and variants, OTS 634, OTS 633
hold-open device: – OTS 530, OTS 430, OTS 330
– electromechanical, e.g. OTS 730 FE – UTS 85 F and variants
– door hold-open magnet and armature plate, electromagnetic
Hold-open systems in general, and the determination of how many Within Germany, e.g., the application directives of the German Insti-
detectors are installed where and how in particular, are subject to tute of Building Technology, Berlin (DIBt) must be observed.
special approval conditions and application directives and require
the licence of a construction control board.
[1] Follow DIBt Application directives (DIBt = German Institute of Building Technology) or corresponding local directives. 37
Smoke switch control unit BMZ 730 H for hold-open systems
Inhalt
Product characteristics
Approved to the directives for hold-open systems by the German
Institute of Building Technology (DIBt).
Control unit for door closers with hold-open feature. With integral
power supply and triggering device (optical smoke switch), inclu-
ding LED indication.
Assembly in the lintel area on side of hinges or opposite to
hinges.
Connection options:
– two hold-open devices
– two ceiling mounted detectors
– manual release button (opener)
On 1-leaf doors used as a component of OTS 730 FER (integrated
in gliding rail), on 2-leaf doors as a component of OTS 730 FER-
SRI (integrated in mechanism of door leaf coordinator).
Technical description
Power supply
– Supply voltage: 230 V AC, 50/60 Hz
– Power input: 21 W
– Output voltage: 24 V DC
– Output current: max. 460 mA
– Power output: max. 10,8 W
– Ambient temperature: +5 to +40 °C
– Protective system: IP 40
– Protection class: II
Optical smoke switch
– Operating voltage: 18 to 28 V DC
– Power input with 28 V DC: max. 22 mA
– Ambient temperature: –20 to +75 °C
– Protective system: IP 40
250 36
38
Accessories for hold-open systems
Inhalt
Product characteristics
Suited for the early recognition of smoul-
33
dering fire and naked flames with smoke
123
31,5
emission.
Smoke detection acc. to EN 54, part 7.
A hold-open system component.
Approved by DIBt (German Institute of
35
Building Technology).
127 As lintel switch for wall mounting.
36
With alarm threshold follow-up and
clogging indicator.
[1] Follow DIBt Application directives (DIBt = German Institute of Building Technology) or corresponding local directives. 39
Accessories for hold-open systems
Inhalt
ORS 143 A
Surface-mounted base for ceiling installati-
on of optical smoke switch ORS 142 in dry
33
rooms.
Order information
59,5
50
Mounting Finish PU Order number
base
Ø 80 ORS 143 A white 1 pc. K-17728-00-0-0
1
ORS 143 W
2
Mounting base for wall installation of optical
6 LED
100
33
5 4
bination with mounting base ORS 142 A.
Order information
40
base
ORS 143 W white 1 pc. K-17494-00-0-0
max. 35
117
ORS 143 UH
Flush-mounted base for ceiling installation
of optical smoke switch ORS 142 in dray
Ø 96 rooms with lowered ceiling.
Order information
42,5
34
40
Accessories for hold-open systems
Inhalt
Product characteristics
Trigger power supply unit for the voltage
supply of smoke switch systems.
A hold-open system component.
Approved by DIBt (German Institute of
163
Building Technology).
High efficiency switching power supply.
Terminals for all external appliances.
78 61
Technical data
81 33,5 8
– Type of contact: Opener
8
– Switching voltage: 30 V DC
– Switching current: 1 A
27
– Protective system: IP 44
41
Accessories for hold-open systems
Inhalt
Product characteristics
Hold-open magnets Technical data: Mounting variants: wall, floor, ceiling, or
– are electrical devices to hold fire doors – Supply voltage: 24 V DC behind the door.
open. A hold-open magnet is a compo- – Current draw: 63 mA Each holding magnet comes with the ap-
nent of a hold-open system. – Current consumption: 1,5 W propriate armature plate for the door leaf.
– are designed according to the closed- – Protective system: IP 20 Hold-open magnets are controlled and
circuit principle: in the event of a fire, Approved to the directives for hold-open monitored by the smoke switch control
the current is interrupted via the smoke systems by the German Institute of Buil- unit BMZ 730 H or by a power supply
switch or the manual actuation button. As ding Technology (DIBt). unit, e.g., NAG 03 or NG 519.
a result, the hold-open magnet is current-
less and therefore deactivated, the door
is released and closed by the door closer.
Standard variant
with steel base plate
On-wall mounting, with concealed terminal
clamp.
93
Ø 50
55
Order information
55 3 Holding force PU Order number
5
65 33
490 N 1 pc. K-17483-00-0-0
Order information
105
Ø 50
65
42
Accessories for hold-open systems
Inhalt
Order information
Ø 50
80
65
Holding Dim. Dim PU Order number
75 4 force „A“ „B“
90 A
490 N 185 150 1 pc. K-17486-00-0-0
490 N 335 300 1 pc. K-17486-01-0-0
Wall
mounting
Ø 50
B
4
90
75
65
Floor
80
mounting
Floor-mounted magnet
Ø 50
Order information
Holding force PU Order number
490 N 1 pc. K-17487-00-0-0
ca. 120
ca. 93
102
85
50,5 15
81 4,5
43
Accessories for hold-open systems
Inhalt
Standard variant
on mounting plate; spring-loaded to ensure
a planar contact between the magnetic
surfaces.
Ø 55
55
44
44 5
Order information
55 5 Description PU Order number
18 Armature plate with spring 1 pc. K-17488-00-0-0
Order information
44 5 5
Description PU Order number
55 79
Armature plate with cushion 1 pc. K-17490-00-0-0
spring
44
Accessories for hold-open systems according to EN 1158
Inhalt
Product characteristics
The mechanical door leaf coordinator ensures the correct closing
sequence of active and inactive door leaves controlled by a door
closer.
Functional mode:
The arm of the door leaf coordinator automatically moves forward
as the inactive leaf opens. At closing, the active leaf is held open
until the inactive leaf pushes the arm in its initial position allowing
the active leaf to close.
Tested and quality controlled to EN 1158.
The door leaf coordinator may be used on fire and smoke doors,
if it is explicitly stated in the approval document or in the test
certificate of the particular door unit.
Appealing design thanks to short control arm and stylish cover
cap.
Easy assembly – only two components must be fixed.
Range of application Low-noise and material-conserving operation.
For 2-leaf timber, PVC, aluminium and steel doors.
Non-handed (DIN lh and DIN rh usable).
Active leaf widths from 700 mm to 1300 mm in combination with
any inactive leaf widths.
423
45
Accessories for hold-open systems according to EN 1158
Inhalt
Carrier bar
Product characteristics
Functional mode:
If, in a panic situation, the door is opened by the inactive leaf, the
carrier bar ensures that the active leaf is taken along at least as
far as the action range of the door leaf coordinator.
Tested and quality controlled to EN 1158.
The carrier bar is approved for use on fire and smoke doors, if it
is explicitly stated in the approval document or test certificate of
particular the door unit.
The carrier bar can also be used without door leaf coordinator.
Range of application
For 2-leaf timber, PVC, aluminium and steel doors.
Non-handed (DIN lh and DIN rh usable).
Door leaf width
– 500 – 800 mm
– 801 – 1300 mm
Rebate height
– Variant “A“ 0 – 11 mm
– Variant “B“ 10 – 17 mm
Door leaf width 801 – 1300 mm silver colour 1 pc. B 8642 0000
Rebate height 0 – 11 mm dark bronze colour 1 pc. B 8642 0005
Variant “A“
Door leaf width 801 – 1300 mm silver colour 1 pc. B 8642 0100
215 / 285 Rebate height 10 – 17 mm dark bronze colour 1 pc. B 8642 0105
Variant “B“
46
Overhead door closer OTS 730
Inhalt
OTS 730 FER – EN 1155 냖 DIN left hand DIN right hand
with electromechanical silver colour 1 pc. K-17227-00-L-1 K-17227-00-R-1
hold-open device, power supply unit dark bronze colour 1 pc. K-17227-00-L-5 K-17227-00-R-5
and smoke switch control unit white (RAL 9016) 1 pc. K-17227-00-L-7 K-17227-00-R-7
(BMZ 730 H)
DIN lh/rh
47
Overhead door closer OTS 630
Inhalt
48
Gliding rails for overhead door closer OTS 630 and OTS 730
Inhalt
Gliding rail with slide arm MF-EA silver colour 1 pc. K-13487-00-0-1
with mechanical hold-open device, dark bronze colour 1 pc. K-13487-00-0-5
on/off switchable white (RAL 9016) 1 pc. K-13487-00-0-7
brass colour 1 pc. K-13487-00-0-3
inox colour 1 pc. K-13487-00-0-8
Gliding rail with slide arm MF-EA silver colour 1 pc. K-14273-00-0-1
with mechanical hold-open device, dark bronze colour 1 pc. K-14273-00-0-5
on/off switchable, white (RAL 9016) 1 pc. K-14273-00-0-7
standard mounting opposite to hinge side brass colour 1 pc. K-14273-00-0-3
inox colour 1 pc. K-14273-00-0-8
Gliding rail with slide arm silver colour 1 pc. K-14850-00-0-1
for subsequent mounting of mechanical hold-open dark bronze colour 1 pc. K-14850-00-0-5
device white (RAL 9016) 1 pc. K-14850-00-0-7
on/off switchable brass colour 1 pc. K-14850-00-0-3
inox colour 1 pc. K-14850-00-0-8
Mechanical hold-open device MF-EA 1 pc. 6-26497-00-0-0
on/off switchable
49
Overhead door closer OTS 730 with door leaf coordinator SRI
Inhalt
SRI system variants with gliding rail, door leaf coordinator integrated in gliding rail,
mounting on hinge side – EN 1158 냖
Figure Variant Finish Order no. [1] Order no. Order no. [2]
OTS 730 OTS 730 SRI BMZ 730 H
2 pieces 1 piece 1 piece
OTS 730 SRI 냖 with gliding rail silver colour K-13688-00-0-1 K-14602-00-0-1
Total leaf width 1240-2800 mm dark bronze K-13688-00-0-5 K-14602-00-0-5
white (RAL 9016) K-13688-00-0-7 K-14602-00-0-7
OTS 730 SRI 냖 with gliding rail silver colour K-13688-00-0-1 K-14607-00-0-1
Total leaf width 1030-1240 mm dark bronze K-13688-00-0-5 K-14607-00-0-5
white (RAL 9016) K-13688-00-0-7 K-14607-00-0-7
OTS 730 FE-SRI 냖 with electromechanical hold- silver colour K-13688-00-0-1 K-14603-00-0-1
open device on active leaf dark bronze K-13688-00-0-5 K-14603-00-0-5
Total leaf width 1240-2800 mm white (RAL 9016) K-13688-00-0-7 K-14603-00-0-7
OTS 730 FE-SRI ( with electromechanical hold- silver colour K-13688-00-0-1 K-14604-00-0-1
open device on both leaves dark bronze K-13688-00-0-5 K-14604-00-0-5
Total leaf width 1240-2800 mm white (RAL K-13688-00-0-7 K-14604-00-0-7
9016)
OTS 730 FE-SRI 냖 with electromechanical hold- silver colour K-13688-00-0-1 K-14608-00-0-1
open device on active leaf dark bronze K-13688-00-0-5 K-14608-00-0-5
Total leaf width 1030-1240 mm white (RAL 9016) K-13688-00-0-7 K-14608-00-0-7
OTS 730 FE-SRI 냖 with electromechanical hold- silver colour K-13688-00-0-1 K-14609-00-0-1
open device on both leaves dark bronze K-13688-00-0-5 K-14609-00-0-5
Total leaf width 1030-1240 mm white (RAL 9016) K-13688-00-0-7 K-14609-00-0-7
OTS 730 FER-SRI 냖 [2] with electromechanical hold- silver colour K-13688-00-0-1 K-14605-00-0-1 K-17220-00-0-1
open device on active leaf dark bronze K-13688-00-0-5 K-14605-00-0-5 K-17220-00-0-5
Total leaf width 1640-2800 mm white (RAL 9016) K-13688-00-0-7 K-14605-00-0-7 K-17220-00-0-7
50
Overhead door closer OTS 730 with door leaf coordinator SRI BG
Inhalt
SRI system variants with gliding rail, door leaf coordinator integrated in gliding rail,
mounting opposite to hinge side – EN 1158 –EN 1158 냖
Figure Variant Finish Order no. [1] Order no. Order no. [2]
OTS 730 OTS 730 SRI BMZ 730 H
2 pieces 1 piece 1 piece
OTS 730 SRI BG 냖 with gliding rail silver colour K-13688-00-0-1 K-14610-00-0-1
Total leaf width 1570-2800 mm dark bronze K-13688-00-0-5 K-14610-00-0-5
white (RAL 9016) K-13688-00-0-7 K-14610-00-0-7
OTS 730 MF-EA SRI BG 냖 with gliding rail silver colour K-13688-00-0-1 K-14610-03-0-1
mit hold-open device MF-EA dark bronze K-13688-00-0-5 K-14610-03-0-5
Total leaf width 1570-2800 mm white (RAL 9016) K-13688-00-0-7 K-14610-03-0-7
OTS 730 FE-SRI BG 냖 with electromechanical hold- silver colour K-13688-00-0-1 K-14611-00-0-1
open device on active leaf dark bronze K-13688-00-0-5 K-14611-00-0-5
Total leaf width 1570-2800 mm white (RAL 9016) K-13688-00-0-7 K-14611-00-0-7
OTS 730 FE-SRI BG 냖 with electromechanical hold- silver colour K-13688-00-0-1 K-14612-00-0-1
open device on both leaves dark bronze K-13688-00-0-5 K-14612-00-0-5
Total leaf width 1570-2800 mm white (RAL 9016) K-13688-00-0-7 K-14612-00-0-7
OTS 730 FER-SRI BG 냖 [2] with electromechanical hold- silver colour K-13688-00-0-1 K-14613-00-0-1 K-17220-00-0-1
open system on active leaf dark bronze K-13688-00-0-5 K-14613-00-0-5 K-17220-00-0-5
Total leaf width 1960-2800 mm white (RAL 9016) K-13688-00-0-7 K-14613-00-0-7 K-17220-00-0-7
51
Door leaf coordinator OTS 730 SRI – Hinge side
Inhalt
Door leaf coordinator integrated in gliding rail for overhead door closer OTS 730,
mounting on hinge side – EN 1158 냖
Figure Variant PU Finish Order number
Door leaf coordinator OTS 730 SRI 냖 1 pc. silver colour K-14602-00-0-1
with gliding rail 1 pc. dark bronze K-14602-00-0-5
for OTS 730 without gliding rail 1 pc. white (RAL 9016) K-14602-00-0-7
Total leaf width 1240-2800 mm 1 pc. black K-14602-00-0-6
1 pc. brass colour K-14602-00-0-3
1 pc. inox colour K-14602-00-0-8
Door leaf coordinator OTS 730 SRI 냖 1 pc. silver colour K-14607-00-0-1
with gliding rail 1 pc. dark bronze K-14607-00-0-5
for OTS 730 without gliding rail 1 pc. white (RAL 9016) K-14607-00-0-7
Total leaf width 1030-1240 mm 1 pc. black K-14607-00-0-6
1 pc. brass colour K-14607-00-0-3
1 pc. inox colour K-14607-00-0-8
Door leaf coordinator OTS 730 FE-SRI 냖 1 pc. silver colour K-14603-00-0-1
with electromechanical hold-open device on active leaf 1 pc. dark bronze K-14603-00-0-5
for OTS 730 without gliding rail 1 pc. white (RAL 9016) K-14603-00-0-7
Total leaf width 1240-2800 mm 1 pc. black K-14603-00-0-6
1 pc. brass colour K-14603-00-0-3
1 pc. inox colour K-14603-00-0-8
Door leaf coordinator OTS 730 FE-SRI 냖 1 pc. silver colour K-14604-00-0-1
with electromechanical hold-open device on both leaves 1 pc. dark bronze K-14604-00-0-5
for OTS 730 without gliding rail 1 pc. white (RAL 9016) K-14604-00-0-7
Total leaf width 1240-2800 mm 1 pc. black K-14604-00-0-6
1 pc. brass colour K-14604-00-0-3
1 pc. inox colour K-14604-00-0-8
Door leaf coordinator OTS 730 FE-SRI 냖 1 pc. silver colour K-14608-00-0-1
with electromechanical hold-open device on active leaf 1 pc. dark bronze K-14608-00-0-5
Total leaf width 1030-1240 mm 1 pc. white (RAL 9016) K-14608-00-0-7
for OTS 730 without gliding rail 1 pc. black K-14608-00-0-6
1 pc. brass colour K-14608-00-0-3
1 pc. inox colour K-14608-00-0-8
Door leaf coordinator OTS 730 FE-SRI 냖 1 pc. silver colour K-14609-00-0-1
with electromechanical hold-open device on both leaves 1 pc. dark bronze K-14609-00-0-5
Total leaf width 1030-1240 mm 1 pc. white (RAL 9016) K-14609-00-0-7
for OTS 730 without gliding rail 1 pc. black K-14609-00-0-6
1 pc. brass colour K-14609-00-0-3
1 pc. inox colour K-14609-00-0-8
Door leaf coordinator OTS 730 FER-SRI 냖 [1] 1 pc. silver colour K-14605-00-0-1
with electromechanical hold-open system on active leaf 1 pc. dark bronze K-14605-00-0-5
Total leaf width 1640-2800 mm 1 pc. white (RAL 9016) K-14605-00-0-7
for OTS 730 without gliding rail 1 pc. black K-14605-00-0-6
1 pc. brass colour K-14605-00-0-3
1 pc. inox colour K-14605-00-0-8
Door leaf coordinator OTS 730 FER-SRI 냖 [1] 1 pc. silver colour K-14606-00-0-1
with electromechanical hold-open system on both sides 1 pc. dark bronze K-14606-00-0-5
Total leaf width 1640-2800 mm 1 pc. white (RAL 9016) K-14606-00-0-7
for OTS 730 without gliding rail 1 pc. black K-14606-00-0-6
1 pc. brass colour K-14606-00-0-3
1 pc. inox colour K-14606-00-0-8
[1] = Smoke switch control unit BMZ 703 H and mounting set FER-SRI must be ordered separately.
52
Door leaf coordinator OTS 730 SRI BG – Opposite to hinge side
Inhalt
Door leaf coordinator integrated in gliding rail for overhead door closer OTS 730,
mounting opposite to hinge side – EN 1158 냖
Figure Variant PU Finish Order number
Door leaf coordinator OTS 730 SRI BG 냖 1 pc. silver colour K-14610-00-0-1
with gliding rail 1 pc. dark bronze K-14610-00-0-5
for OTS 730 without gliding rail 1 pc. white (RAL 9016) K-14610-00-0-7
Total leaf width 1570-2800 mm 1 pc. black K-14610-00-0-6
1 pc. brass colour K-14610-00-0-3
1 pc. inox colour K-14610-00-0-8
Door leaf coordinator OTS 730 MF-EA SRI BG 냖 1 pc. silver colour K-14610-03-0-1
with gliding rail 1 pc. dark bronze K-14610-03-0-5
for OTS 730 without gliding rail 1 pc. white (RAL 9016) K-14610-03-0-7
mit hold-open device MF-EA 1 pc. black K-14610-03-0-6
Total leaf width 1570-2800 mm 1 pc. brass colour K-14610-03-0-3
1 pc. inox colour K-14610-03-0-8
Door leaf coordinator OTS 730 FE-SRI BG 냖 1 pc. silver colour K-14611-00-0-1
with electromechanical hold-open device on active leaf 1 pc. dark bronze K-14611-00-0-5
for OTS 730 without gliding rail 1 pc. white (RAL 9016) K-14611-00-0-7
Total leaf width 1570-2800 mm 1 pc. black K-14611-00-0-6
1 pc. brass colour K-14611-00-0-3
1 pc. inox colour K-14611-00-0-8
Door leaf coordinator OTS 730 FE-SRI BG 냖 1 pc. silver colour K-14612-00-0-1
with electromechanical hold-open device on both leaves 1 pc. dark bronze K-14612-00-0-5
for OTS 730 without gliding rail 1 pc. white (RAL 9016) K-14612-00-0-7
Total leaf width 1570-2800 mm 1 pc. black K-14612-00-0-6
1 pc. brass colour K-14612-00-0-3
1 pc. inox colour K-14612-00-0-8
Door leaf coordinator OTS 730 FER-SRI BG 냖 [1] 1 pc. silver colour K-14613-00-0-1
with electromechanical hold-open device on active leaf 1 pc. dark bronze K-14613-00-0-5
for OTS 730 without gliding rail 1 pc. white (RAL 9016) K-14613-00-0-7
Total leaf width 1960-2800 mm 1 pc. black K-14613-00-0-6
1 pc. brass colour K-14613-00-0-3
1 pc. inox colour K-14613-00-0-8
Door leaf coordinator OTS 730 FER-SRI BG 냖 [1] 1 pc. silver colour K-14614-00-0-1
with electromechanical hold-open system on both sides 1 pc. dark bronze K-14614-00-0-5
Total leaf width 1960-2800 mm 1 pc. white (RAL 9016) K-14614-00-0-7
for OTS 730 without gliding rail 1 pc. black K-14614-00-0-6
1 pc. brass colour K-14614-00-0-3
1 pc. inox colour K-14614-00-0-8
[1] = Smoke switch control unit BMZ 703 H and mounting set FER-SRI must be ordered separately.
53
Accessories for overhead door closer OTS 730
Inhalt
54
Accessories for overhead door closer OTS 630
Inhalt
55
Accessories for overhead door closer OTS 630 and OTS 730
Inhalt
Axle extension
5 mm black 1 pc. K-13490-05-0-6
10 mm black 1 pc. K-13490-10-0-6
15 mm black 1 pc. K-13490-15-0-6
20 mm black 1 pc. K-13490-20-0-6
Safety screw for cover caps silver colour 1 pc. K-14451-00-0-1
10 pieces per bag
56
Overhead door closer OTS 610, OTS 633 and OTS 634
Inhalt
57
Overhead door closer OTS 530
Inhalt
58
Accessories for overhead door closer OTS 530
Inhalt
59
Overhead door closer OTS 430 and OTS 440
Inhalt
Gliding rail with slide arm MF-EA silver colour 1 pc. K-17183-01-0-1
for OTS 210, OTS 440 dark bronze colour 1 pc. K-17183-01-0-5
with mechanical hold-open device, white (RAL 9016) 1 pc. K-17183-01-0-7
on/off switchable black 1 pc. K-17183-01-0-6
60
Overhead door closer OTS 210 and OTS 330
Inhalt
Gliding rail with slide arm MF-EA silver colour 1 pc. K-17183-01-0-1
for OTS 210, OTS 440 dark bronze colour 1 pc. K-17183-01-0-5
with mechanical hold-open device white (RAL 9016) 1 pc. K-17183-01-0-7
on/off switchable black 1 pc. K-17183-01-0-6
61
Overhead door closer OTS 140, OTS 200 and OTS 200 G
Inhalt
62
Accessories for OTS 140, 200, 210, 330, 430 and 440
Inhalt
63
Overhead door closer OTS 81
Inhalt
Distributed by
BKS GmbH
Postfach 10 02 10
D-42502 Velbert
Tel. +49 (0)2051 201-0
www.g-u.com
64
Accessories for overhead door closer OTS 81
Inhalt
Angular soffit bracket 2-4 1 pc. B 8170 0000 B 8170 0005 B 8170 0006
5 1 pc. B 8170 0100 B 8170 0105 B 8170 0106
Flat bracket 2-4 1 pc. B 8171 0000 B 8171 0005 B 8171 0006
5 1 pc. B 8171 0100 B 8171 0105 B 8171 0106
Soffit bracket 2-4 1 pc. B 8172 0000 B 8172 0005 B 8172 0006
5 1 pc. B 8172 0100 B 8172 0105 B 8172 0106
Mounting plate 2-4 1 pc. B 8173 0000 B 8173 0005 B 8173 0006
Angular bracket 2-5 1 pc. B 8174 0000 B 8174 0005 B 8174 0006
for parallel arm assembly
Base plate 2-5 1 pc. B 8177 0000 B 8177 0005 B 8177 0006
Mounting plate 3-4 1 pc. B 8178 0000 B 8178 0005 B 8178 0006
5 1 pc. B 8178 0100 B 8178 0105 B 8178 0106
Distributed by
BKS GmbH
Postfach 10 02 10
D-42502 Velbert
Tel. +49 (0)2051 201-0
www.g-u.com
65
Arms for overhead door closer OTS 81
Inhalt
Extended arm 2-4 1 pc. B 8183 0000 B 8183 0005 B 8183 0006
5 1 pc. B 8185 0000 B 8185 0005 B 8185 0006
Hold-open arm 2-3 1 pc. B 8183 0200 B 8183 0205 B 8183 0206
4 1 pc. B 8184 0200 B 8184 0205 B 8184 0206
5 1 pc. B 8185 0200 B 8185 0205 B 8185 0206
Distributed by
BKS GmbH
Postfach 10 02 10
D-42502 Velbert
Tel. +49 (0)2051 201-0
www.g-u.com
66
Overhead door closer OTS 80
Inhalt
Distributed by
BKS GmbH
Postfach 10 02 10
D-42502 Velbert
Tel. +49 (0)2051 201-0
www.g-u.com
67
Accessories and arms for overhead door closer OTS 80
Inhalt
Distributed by
BKS GmbH
Postfach 10 02 10
D-42502 Velbert
Tel. +49 (0)2051 201-0
www.g-u.com
68
Rebate door closer 20 and 24
Inhalt
69
Floor springs UTS 85, UTS 60, UTS 50, UTS 42, UTS 840
Inhalt
UTS 60 – EN 1154 냖
without hold-open 1 pc. K-17367-01-0-8
with mechanical hold-open at 90° 1 pc. K-17367-02-0-8
with mechanical hold-open at 105° 1 pc. K-17367-03-0-8
UTS 50 – EN 1154 냖
without hold-open 1 pc. K-17366-01-0-8
with mechanical hold-open at 90° 1 pc. K-17366-02-0-8
with mechanical hold-open at 105° 1 pc. K-17366-03-0-8
UTS 42 – EN 1154 냖
without hold-open 1 pc. K-15342-00-0-0
with mechanical hold-open at 90°/85° [1] 1 pc. K-15343-00-0-0
with mechanical hold-open at 95°/90° [1] 1 pc. K-15344-00-0-0
70
Door leaf coordinator UTS 85 SRI
Inhalt
Integrated door leaf coordinator UTS 85 SRI without cover plate – EN 1158 냖
71
Accessories for floor springs
Inhalt
Accessories set UTS 840 stainless steel matt finish 1 pc. K-17477-00-0-8
for double action swing doors brass colour 1 pc. K-17477-00-0-3
with top and bottom pivots and door strap
72
Accessories for floor springs
Inhalt
Axle, top part UTS 85 DIN left hand DIN right hand
tapered and offset 5° 1 pc. K-13481-00-L K-13481-00-R
for all glass doors with top stop
Axle, top part UTS 85 DIN left hand DIN right hand
with square spindle for DIN lh/rh doors, 1 pc. K-13482-00-L-0 K-13482-00-R-0
with square spindle for double action swing 1 pc. K-13482-00-0-0 K-13482-00-0-0
doors
73
Accessories for floor springs
Inhalt
Steel top pivot Variant 2 DIN left hand DIN right hand
drop-forged, galvanised 41 mm 1 pc. K-13050-41-L-1 K-13050-41-R-1
45 mm 1 pc. K-13050-45-L-1 K-13050-45-R-1
50 mm 1 pc. K-13050-50-L-1 K-13050-50-R-1
Top pivot for single action swing doors, Variant 2 DIN left hand DIN right hand
steel 41 mm 1 pc. K-13049-00-L-1 K-13049-00-R-1
drop-forged, galvanised
74
Accessories for floor springs
Inhalt
75
Accessories for floor springs
Inhalt
Accessories for timber and steel double action swing doors and reversible timber doors
Figure Variant Hinge pin mm PU Order number
Top pivot - top part, steel
galvanised 45 mm 1 pc. 6-24716-45-0-1
76
Smoke switch control unit, accessories for hold-open systems
Inhalt
Power supply units, optical smoke detectors and manual actuation buttons
Figure Variant Finish PU Order number
Power supply unit NAG 03 white 1 pc. K-17493-00-0-7
Wall-mounting (surface)
77
Accessories for hold-open systems
Inhalt
Hold-open magnet
On-wall mounting 490 1 pc. K-17485-00-0-0
with housing and interruptor
Hold-open magnet
Floor-mounting 490 1 pc. K-17487-00-0-0
with housing and interruptor
78
Accessories for hold-open systems
Inhalt
Carrier bar
Polyurethane roller buffer Rebate Inactive door leaf
Variant mm mm
“A“ 0 - 11 500 - 800 1 pc. B 8642 0200 B 8642 0205
“B“ 10 - 17 500 - 800 1 pc. B 8642 0300 B 8642 0305
Carrier bar
Polyurethane roller buffer Rebate Inactive door leaf
Variant mm mm
„A“ 0 - 11 801 - 1 pc. B 8642 0000 B 8642 0005
„B“ 10 - 17 801 - 1 pc. B 8642 0100 B 8642 0105
special colours
Replacement rubber plug with screw 1 pc. B 3919 0102
Door holder 30 painted silver colour 1 pc. B 3933 0101
painted dark brown 1 pc. B 3933 0137
Replacement rubber plug without screw 1 pc. B 3909 0101
Door stop floor stainless steel matt finish 1 pc. B 7122 0000
79
Acceptance test of hold-open systems
Inhalt
When the acceptance test is completed successfully, a durable sign c. Service without service contract
supplied by the manufacturer must be put on the wall in the vicinity
the fire rated door with the inscription
We must point out that for G.U hold-open systems only tested and
licensed devices of our own make must be used.
Hold-open system
Accepted by ........................................................ Licence notices providing evidence of the acceptance or of the
(name of company, month and year of acceptance) surveillance authority are made available on request.
80
Notes
Inhalt
81
Notes
Inhalt
82
Gretsch-Unitas Group of Companies
Inhalt
As a specialist manufacturer
of hardware and ventilators,
Gretsch-Unitas have been, for
Gretsch-Unitas GmbH many years, the brand leader in
Baubeschläge several product areas.
D-71252 Ditzingen
Tel. +49 (0)7156 301-0 The market acceptability of the
Fax +49 (0)7156 301-293 wide ranging product program-
www.g-u.com me of builder's hardware and
ventilators with up-to-date
technology and design is proved
in daily competition.
FERCO INTERNATIONAL is
France's largest and most
widely used builder's hardware
FERCO International S.A.S. supplier.
F-57401 Sarrebourg The extensive programme of
Tel. +33 (0)3 87 23 31 11 modern hardware is distributed
Fax +33 (0)3 87 03 54 06 world wide.
www.ferco.fr