Professional Documents
Culture Documents
Nordfab Duct Engineering Specifications-3
Nordfab Duct Engineering Specifications-3
General Specifications
Structural Integrity and General Engineering Specification for Quick-Fit Ducting
Applications While Nordfab is currently unaware of accordance with the SMACNA, “ HVAC
Nordfab’s laser welded seam Quick-Fit ® any method of evaluating dust collec- AIR DUCT LEAKAGE TEST MANUAL”.
Ducting System has been used in many tion piping alone, the following data is The information gives the leakage rate
different industrial applications, and under presented using the criteria for all duct, per joint of duct at various pressures.
various negative static pressures. including HVAC. This data is presented To utilize the chart, count the number
The typical design range we see in our only for the purpose of indicating of clamps (this equals the number
applications range from -2" wg to - 28" acceptability of the QF in dust/fume of pieces) per size and multiply
wg; however, we have some systems removal in a negative pressure situa- by the number given beside the
operating at vacuums of -32" wg to -42" tion and should not be confused with corresponding diameter and under the
wg under normal operating parameters. the ducting that uses tape or gaskets applicable pressure. These numbers
Our pipe comes in 5' lengths with a rolled as sealant in the positive conveyance assume that the product is correctly
lip on each end, thus providing reinforce- of air. installed, free of dents in the joining
ment every 5', which presents a sound
structural design that should be as strong Leakage Rate Leakage Class Determined In
or stronger than any pipe in its class Standard QF ductwork is designed Accordance With SMACNA
according to SMACNA guidelines and to provide tight sealing and efficient Class 3
regulations. airflow under negative pressures.
Avg. leakage per 100'
To that end, we are providing the ø in.
following information for piping 5" SP IO"SP
Structural Integrity
situations where fan sizing is of 4-6 5 CFM 6 CFM
All fit-together ducting systems allow for
extreme importance. The following 7 - 10 2.5 CFM 3.5 CFM
some degree of leakage where they are
data was obtained using standard
joined. QF® ducting is no exception and is 11 - 24 2 CFM 4 CFM
components and was performed in
not sold as an airtight system.
In comparison to other ducting typically Leakage Rate In CFM Per QF Joint
used in fit-together / clamp-together
ø In. 3 WG 5 WG 7.5 WG 10 WG 15 WG 20 WG 25 WG 30 WG
systems, Nordfab’s QF duct pipe has fully
welded, leak-tight laser or plasma welded 4 0.20 0.25 0.30 0.30 0.35 0.50 0.60 0.80
seams. Spiral and other ducting with 5 0.20 0.25 0.30 0.30 0.35 0.50 0.60 0.80
lockform seams are not fully welded at the
6 0.20 0.25 0.30 0.30 0.35 0.50 0.60 0.80
pipe seams and can be expected to have
7 0.20 0.25 0.30 0.30 0.35 0.50 0.60 0.80
higher leakage rates than QF.
Application of sealants to the individual 8 0.20 0.25 0.30 0.30 0.35 0.50 0.60 0.80
rolled ends can also enhance the tightness 9 0.20 0.25 0.30 0.30 0.35 0.50 0.60 0.80
of the system. However, the QF system 10 0.20 0.25 0.30 0.30 0.35 0.50 0.60 0.80
is sold as a quick way of installing and
12 0.30 0.30 0.40 0.40 0.40 0.60 0.70 0.90
modifying ductwork while at the same
time retaining the usability of each com- 14 0.30 0.30 0.50 0.70 0.80 0.80 0.90 1.10
ponent. In short, QF is designed with the 16 0.30 0.40 0.60 0.70 1.00 1.10 1.20 1.40
capability to be taken apart, re-assembled, 18 0.40 0.40 0.70 0.80 1.10 1.30 1.50 1.70
stored or moved. Completely eliminating 20 0.40 0.60 0.80 0.90 1.20 1.50 1.70 2.00
the possibility for leakage jeopardizes the
22 0.40 0.60 0.80 1.10 1.40 1.50 2.00 2.20
inherent benefits of the duct.