Professional Documents
Culture Documents
k3hb-V Weighing Indicator Datasheet en
k3hb-V Weighing Indicator Datasheet en
K3HB-V CSM_K3HB-V_DS_E_11_6
1
K3HB-V
Accessories (Sold Separately)
K32-DICN: Special Cable (for event inputs, with 8-pin connector)
K32-BCD: Special BCD Output Cable
Specifications
Ratings
Power supply voltage 100 to 240 VAC (50/60 Hz), 24 VAC/VDC, DeviceNet power supply: 24 VDC
Allowable power supply voltage range 85% to 110% of the rated power supply voltage, DeviceNet power supply: 11 to 25 VDC
Power consumption 100 to 240 V: 18 VA max. (max. load)
(See note 1.) 24 VAC/DC: 11 VA/7 W max. (max. load)
Current consumption DeviceNet power supply: 50 mA max. (24 VDC)
Input DC voltage
A/D conversion method Delta-Sigma method
External power supply 10 VDC ±5%, 100 mA (models with external power supply only) or 5 VDC, 100 mA (models with external
power supply only)
Event inputs Timing input NPN open collector or no-voltage contact signal
(See note 2.) ON residual voltage: 3 V max.
ON current at 0 Ω: 17 mA max.
Max. applied voltage: 30 VDC max.
OFF leakage current: 1.5 mA max.
Startup compensation NPN open collector or no-voltage contact signal
timer input ON residual voltage: 2 V max.
Hold input ON current at 0 Ω: 4 mA max.
Max. applied voltage: 30 VDC max.
Reset input OFF leakage current: 0.1 mA max.
Forced-zero input
Bank input
Output ratings (depends Relay output 250 VAC, 30 VDC, 5 A (resistive load)
on the model) Mechanical life expectancy: 5,000,000 operations, Electrical life expectancy: 100,000 operations
Transistor output Maximum load voltage: 24 VDC, Maximum load current: 50 mA, Leakage current: 100 μA max.
Linear output Linear output 0 to 20 mA DC, 4 to 20 mA DC:
Load: 500 Ω max, Resolution: Approx. 10,000, Output error: ±0.5% FS
Linear output 0 to 5 VDC, 1 to 5 VDC, 0 to 10 VDC:
Load: 5 kΩ max, Resolution: Approx. 10,000, Output error: ±0.5% FS
(1 V or less: ±0.15 V; no output for 0 V or less)
Display method Negative LCD (backlit LED) display
7-segment digital display (Character height: PV: 14.2 mm (green/red); SV: 4.9 mm (green)
Main functions Scaling function, measurement operation selection, averaging, previous average value comparison, forced-
zero, zero-limit, output hysteresis, output OFF delay, output test, teaching, display value selection, display
color selection, key protection, bank selection, display refresh period, maximum/minimum hold, reset
Ambient operating temperature −10 to 55°C (with no icing or condensation)
Ambient operating humidity 25% to 85%
Storage temperature −25 to 65°C (with no icing or condensation)
Altitude 2,000 m max.
Accessories Watertight packing, 2 fixtures, terminal cover, unit stickers, operation manual. DeviceNet models also include
a DeviceNet connector (Hirose HR31-5.08P-5SC(01)) and crimp terminals (Hirose HR31-SC-121) (See note
3.)
Note: 1. DC power supply models require a control power supply capacity of approximately 1 A per Unit when power is turned ON. Particular attention is required
when using two or more DC power supply models. The OMRON S8VS-series DC Power Supply Unit is recommended.
2. PNP input types are also available.
3. For K3HB-series DeviceNet models, use only the DeviceNet Connector included with the product. The crimp terminals provided are for Thin Cables.
2
K3HB-V
Characteristics
Display range −19,999 to 99,999
Sampling period 20 ms (50 times/second)
Comparative output response time 100 ms max.
Linear output response time 150 ms max.
Insulation resistance 20 MΩ min. (at 500 VDC)
Dielectric strength 2,300 VAC for 1 min between external terminals and case
Noise immunity 100 to 240 VAC models:
±1,500 V at power supply terminals in normal or common mode
(waveform with 1-ns rising edge and pulse width of 1 μs/100 ns)
24 VAC/VDC models:
±1,500 V at power supply terminals in normal or common mode
(waveform with 1-ns rising edge and pulse width of 1 μs/100 ns)
Vibration resistance Frequency: 10 to 55 Hz; Acceleration: 50 m/s2, 10 sweeps of 5 min each in X, Y, and Z directions
Shock resistance 150 m/s2 (100 m/s2 for relay outputs) 3 times each in 3 axes, 6 directions
Weight Approx. 300 g (Base Unit only)
Degree of Front panel Conforms to NEMA 4X for indoor use (equivalent to IP66)
protection Rear case IP20
Terminals IP00 + finger protection (VDE0106/100)
Memory protection EEPROM (non-volatile memory)
Number of rewrites: 100,000
Applicable standards UL61010-1, CSA C22.2 No. 61010-1-04
EN61010-1 (IEC61010-1): Pollution degree 2/Overvoltage category II
EN61326-1
EMC EMI: EN61326-1 Industrial electromagnetic environment
Electromagnetic radiation interference
CISPR 11 Group 1, Class A
Terminal interference voltage
CISPR 11 Group 1, Class A
EMS: EN61326-1 Industrial electromagnetic environment
Electrostatic Discharge Immunity
EN61000-4-2: 4 kV (contact), 8 kV (in air)
Radiated Electromagnetic Field Immunity
EN61000-4-3: 10 V/m 1 kHz sine wave amplitude modulation (80 MHz to 1 GHz, 1.4 to 2 GHz)
Electrical Fast Transient/Burst Immunity
EN61000-4-4: 2 kV (power line), 1 kV (I/O signal line)
Surge Immunity
EN61000-4-5: 1 kV with line (power line), 2 kV with ground (power line)
Conducted Disturbance Immunity
EN61000-4-6: 3 V (0.15 to 80 MHz)
Power Frequency Magnetic Immunity
EN61000-4-8: 30 A/m (50 Hz) continuous time
Voltage Dips and Interruptions Immunity
EN61000-4-11: 0.5 cycle, 0°/180°, 100% (rated voltage)
3
K3HB-V
Input Ranges (Measurement Range and Accuracy)
Input type Range Set value Measurement range Input impedance Accuracy Allowable
instantaneous
overload (30 s)
K3HB-VLC A a lc 0.00 to 199.99 mV 1 MΩ min. ±0.1% rdg ±1 digit max. ±200 V
Load Cell, mV B b lc 0.000 to 19.999 mV ±0.1% rdg ±5 digits max.
C c lc ±100.00 mV ±0.1% rdg ±3 digits max.
D d lc ±199.99 mV ±0.1% rdg ±1 digit max.
Note: 1. The accuracy is for an ambient temperature of 23±5°C. For all ranges,10% or less of max. input ±0.1% FS.
2. The letters “rdg” mean “reading.”
Input type a lc b lc c lc d lc
Connected E2 E6 E3 E6 E4 E6 E5 E6
terminals
(mV) 199.99 199.99
200.000
150.000
100.00
100.000
19.999
50.000
0.00
0.00 0.000
−50.00
−100.00
−100.00
−150.00
−200.00
−199.99
Maximum -19.99 to 219.99 mV -1.999 to 21.999 mV -110.00 to 110.00 mV -199.99 to 219.99 mV
measurement range
4
K3HB-V
Common Specifications
Event Input Ratings
Input type S-TMR, HOLD, RESET, ZERO, BANK1, BANK2, TIMING
BANK4
Contact ON: 1 kΩ max., OFF: 100 kΩ min. ---
No-contact ON residual voltage: 2 V max. ON residual voltage: 3 V max.
OFF leakage current: 0.1 mA max. OFF leakage current: 1.5 mA max.
Load current: 4 mA max. Load current: 17 mA max.
Maximum applied voltage: 30 VDC max. Maximum applied voltage: 30 VDC max.
Output Ratings
Contact Output Transistor Output
Item Resistive loads Inductive loads Maximum load voltage 24 VDC
(250 VAC, cosφ=1; (250 VAC, closed
Maximum load current 50 mA
30 VDC, L/R=0 ms) circuit, cosφ=0.4;
30 VDC, L/R=7 ms) Leakage current 100 μA max.
Rated load 5 A at 250 VAC 1 A at 250 VAC
5 A at 30 VDC 1 A at 30 VDC
Rated through 5A
current
Mechanical life 5,000,000 operations
expectancy
Electrical life 100,000 operations
expectancy
Linear Output
Item 0 to 20 mA 4 to 20 mA 0 to 5 V 1 to 5 V 0 to 10 V
Allowable load impedance 500 Ω max. 5 kΩ min.
Resolution Approx. 10,000
Output error ±0.5%FS ±0.5%FS (1 V or less: no output for ±0.15 V; 0 V or less)
5
K3HB-V
DeviceNet Communications
Communications protocol Conforms to DeviceNet
Supported communi- Remote I/O communications Master-Slave connection (polling, bit-strobe, COS, cyclic)
cations Conforms to DeviceNet communications standards.
I/O allocations Allocate any I/O data using the Configurator.
Allocate any data, such as DeviceNet-specific parameters and variable area for Digital
Indicators.
Input area: 2 blocks, 60 words max.
Output area: 1 block, 29 words max.
(The first word in the area is always allocated for the Output Execution Enabled Flags.)
Message communications Explicit message communications
CompoWay/F communications commands can be executed (using explicit message
communications)
Connection methods Combination of multi-drop and T-branch connections (for trunk and drop lines)
Baud rate DeviceNet: 500, 250, or 125 Kbps (automatic follow-up)
Communications media Special 5-wire cable (2 signal lines, 2 power supply lines, 1 shield line)
Communications distance
Baud rate Network length Drop line length Total drop line
(max.) (max.) length (max.)
500 Kbps 100 m (100 m) 6m 39 m
250 Kbps 100 m 6m 78 m
(250 m)
125 Kbps 100 m 6m 156 m
(500 m)
The values in parentheses are for Thick Cable.
Communications power supply 24-VDC DeviceNet power supply
Allowable voltage fluctuation range 11 to 25-VDC DeviceNet power supply
Current consumption 50 mA max. (24 VDC)
Maximum number of nodes 64 (DeviceNet Configurator is counted as one node when connected)
Maximum number of slaves 63
Error control checks CRC errors
DeviceNet power supply Supplied from DeviceNet communications connector
EEP-ROM Indications
BCD
• Input circuit Drive Transistor
BCD I/O Drive
• Output circuit
• Transistor
circuit circuit output
output circuit
Micro-
computer
Event input Digital input Waveform Drive
circuit shaping circuit circuit
X Relay output
VO VDD VCOM
VO
Power supply circuit (isolated) DC-DC
Converter (isolated)
Power supply
6
K3HB-V
Power Supply Derating Curve for Sensor (Reference Value)
With 12 V With 10 V
100 100
80 80
60 60
40 40
20 20
0 0
20 10 0 10 20 30 40 50 60 20 10 0 10 20 30 40 50 60
Note: 1. The above values are for standard mounting. The derating curve differs depending on the mounting conditions.
2. Do not use the Sensor outside of the derating area (i.e., do not use it in the area labeled (1) in the above graphics). Doing so may occa-
sionally cause deterioration or damage to internal components.
7
K3HB-V
BCD Output Timing Chart
A REQUEST signal from a Programmable Controller or other external device is required to read BCD data.
The data is set in approximately 30 ms from the rising edge of the Measurement data is output every 64 ms while the REQUEST signal
REQUEST signal and the DATA VALID signal is output. remains ON.
When reading the data from a Programmable Controller, start
Note: If HOLD is executed when switching between data 1 and data
reading the data when the DATA VALID signal turns ON.
2, either data 1 or data 2 is output depending on the timing of
The DATA VALID signal will turn OFF 40 ms later, and the data will
the hold signal. The data will not go LOW.
turn OFF 16 ms after that.
REQ. (1)
K3HB
(1)
Programmable
Controller REQ. (2)
K3HB
REQ. (3)
(2)
DATA (including POL and
OVER) and DATA VALID can
be used in a wired OR. DATA (1) (2) (3)
K3HB RUN, HH, H, PASS, L, and
(3) LL are always output, with or
without a REQUEST signal. DATA
Do not used a wired OR VALID
(See note.) (See note.) (See note.)
connect for these signals.
Note: Leave 20 ms min. between DATA VALID turning OFF and the REQUEST signal.
2.1 IN 2.1
3.2 IN 3.2
10° 10°
4.4 4.4
Internal circuit
IN
5.8 IN 5.8
IN To 101
To 102
Internal circuit
240 Ω 240 Ω
Refer to the following User's Manual for application precautions and other information required when using the Digital Indicator:
K3HB-S/-X/-V/-H Digital Indicator User's Manual (Cat. No. N128)
The manual can be downloaded from the following site in PDF format: OMRON Industrial Web http://www.fa.omron.co.jp
8
K3HB-V
Connections
Terminal Arrangement
Note: Insulation is used between signal input, event input, output, and power supply terminals.
A B C D E
A Operating Power Supply 1
2
100 to 240 VAC 3
24 VAC/ VDC
4
5
A1
6
A2
PASS B2
Relay Outputs Relay Outputs Transistor Outputs DeviceNet Connector (Included)
<C1> <C2> <T1> <T2> <DRT>
B3
NPN PNP
Sensor power supply
C1 HH C1 HH C1
1 2 3 4 5
N/C B4
10 VDC 100 mA
12 VDC 80 mA
5 VDC 100 mA
+ H C2 H C2 H C2
B5
C3 COM C3 PASS C3
B6
− C4 L C4 L C4
<K33- <K33- <K33- 1: V− (Power supply cable: Black)
CPE> CPB> CPA> L C5 LL C5 LL C5 2: CAN L (Communications cable: Blue)
Sensor power supply + 3: Shield
C6 COM C6 COM C6 4: CAN H (Communications cable: White)
linear output 5: V+ (Power supply cable: Red)
+ Applicable Connector:
0-5/1-5/ 0-5/1-5/ 0-5/1-5/ B1 HR31-5.08P-5SC (01)
N/C N/C N/C (HIROSE ELECTRIC CO., LTD.)
0-10 V 0-10 V 0-10 V * Attach the provided crimp terminals.
− B2 BCD (NPN Open Collector): BCD
+
B3 Applicable Connector (Sold separately)
0-20/ 0-20/ 0-20/
Sensor power supply
10 VDC 100 mA
5 VDC 100 mA
12 VDC 80 mA
12 VDC 80 mA
5 VDC 100 mA
B2
N/C Contact output Transistor Output
B3
(NPN Open Collector)
Sensor power supply
B4
10 VDC 100 mA
5 VDC 100 mA
12 VDC 80 mA
+ 5V
B5
B6 HH HH
−
<K33-E> <K33-B> <K33-A> H H
Sensor power supply + L L
communications
LL LL
B (+) SD B (+) SD B (+) SD B1 PASS PASS
A (−) RD A (−) RD A (−) RD B2
10 VDC 100 mA
12 VDC 80 mA
12 VDC 80 mA
5 VDC 100 mA
5 VDC 100 mA
+
B5
• Always use a EN/IEC-compliant power supply with reinforced insulation or
B6
− double insulation for the DeviceNet power supply.
RS-485 RS-232C RS-485 RS-232C RS-485 RS-232C
<K33- <K33- <K33- <K33- <K33- <K33-
• The product must be used indoors for the above applicable standards to
FLK3E> FLK1E> FLK3B> FLK1B> FLK3A> FLK1A>
apply.
• The K3HB-XVA@@ complies with UL standards when the applied input
voltage is within the range 0 to 150 VAC.
9
K3HB-V
E Analog Input
D Event Input
• Use terminal pin D6 as the common terminal.
Models with Terminal Blocks
<K35-1><K35-3> • Use NPN open collector or no-voltage contacts for event input.
PNP types are also available.
D1 TIMING
12 V 12 V
D2 S-TMR S-TMR: D2
HOLD: D3
D3 HOLD RESET: D4
ZERO: D5 4.7 kΩ TIMING 560 Ω
D4 RESET
D5 ZERO D1
3.9 kΩ 750 Ω
D6 COM
10
K3HB-V
Main Functions
Measurement
Timing Hold
(b2−a2)
(b1−a1)
Measurement value
Measurement value b1 'b2
Bottom hold value a1 'a2
Time Time
TIMING ON TIMING ON
input OFF input OFF
Scaling converts input signals in any way required before displaying Slight changes can be removed from input signals to detect only
them. The values can be manipulated by shifting, inverting, or +/– extreme changes.
reversing.
Display value Display value
Input value 1 Input value 2 Input value 2 Input value 1 Input value
(inp.a1) (inp.a2) Input value (inp.a2) (inp.a1)
Teaching
Standby Sequence
11
K3HB-V
Input Compensation/Display
Forced-zero Display Value Selection
The current display value can be selected from the present value,
Forces the present value to 0. (Convenient for setting reference val- the maximum value, and the minimum value.
ues or deducting tares for weight measurement.)
Step Value
Tare Zero
It is possible to specify (i.e., restrict) the values that the smallest dis-
Shifts the current value measured with a forced zero to 0 again. It is played digit can change by. For example, if the setting is 2, the small-
possible to measure two or more compounds separately and then, est digit will only take the values 0, 2, 4, 6, or 8 and if the setting is 5,
by releasing the tare zero and forced-zero, measure the combined it will only take the values 0 or 5. If the setting is 10, it will only take
total. the value of 0.
Zero-trimming
Changes the display value to 0 for input values less than the set
value. It is enabled in normal mode only. (This function can be used,
for example, to stop negative values being displayed or to eliminate
flickering and minor inconsistencies near 0.)
Display
Zero-limit
setting
Input
Interruption Memory
P 100.05
Comparative set value L 110.00
L
99.87
110.00
Red
12
K3HB-V
Output
The output pattern for comparative outputs can be selected. In addi- Prevents comparative output chattering when the measurement
tion to high/low comparison with set values, output based on level value fluctuates slightly near the set value.
changes is also possible. (Use the type of output pattern appropriate
for the application.) Example: Comparative Output Pattern (Standard Output)
Hysteresis
Comparative set value H Hysteresis
Comparative Standard Output Measurement Level Output Measurement
value Comparative value
set value HH set value HH
Comparative Higher Comparative Higher Comparative set value L
set value H set value H
Comparative Comparative
set value L set value L
Comparative Lower Comparative Lower Comparative output H
set value LL set value LL
Output HH ON Output HH ON Comparative output L
Output H OFF Output H OFF
Output PASS
Startup Compensation Timer
Output PASS
Output L Output L
Output LL Output LL
Measurement can be stopped for a set time using external input.
Measurement
Comparative Zone Output value Input
set value HH
Comparative Higher
set value H H comparative set value
Comparative
set value L
Comparative Lower
set value LL
Output HH ON
Output H OFF Time
Output PASS
H output Startup
Output L compensation
Output LL time set time
H input
Output Logic
PASS Output Change
Dimensions
101.2 Terminal cover (included)
91
Character Size for Main Display (mm) Panel Cutout Dimensions
PV display SV display 120 min.
14.2 4.9
100
3.5
(112)
7.6
75 min.
92+0.8
0
12 45+0.6
0
1.3
95*
2
96
Mounting Recommended Panel Thickness
1 to 8 mm.
Mount the product horizontally.
48 44.8
*DeviceNet models: 97 mm
Terminal: M3, Terminal Cover: Accessory
13
K3HB-V
Wiring Precautions Mounting Method
• For terminal blocks, use the crimp terminals suitable for M3 screws. 1. Insert the K3HB into the mounting cutout in the panel.
• Tighten the terminal screws to the recommended tightening torque 2. Insert watertight packing around the Unit to make the mounting
of approx. 0.5 N⋅m. watertight.
• To prevent inductive noise, separate the wiring for signal lines from Watertight
that for power lines. packing
Wiring
• Use the crimp terminals suitable for M3 screws shown below.
5.8 mm max.
5.8 mm max.
3. Insert the fixture into the grooves on the left and right sides of the
rear case and push until it reaches the panel and is fixed in place.
• Select the appropriate units from the unit sticker sheets provided
and attach the sticker to the Indicator.
10°
30°
Watertight Cover
Y92A-49N
Rubber Packing
K32-P1
If the rubber packing is lost or damaged, it can
be ordered using the following model number:
K32-P1.
In the interest of product improvement, specifications are subject to change without notice.
14
Terms and Conditions Agreement
Read and understand this catalog.
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you
have any questions or comments.
Warranties.
(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship
for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron
disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER
ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.
Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the
Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at
Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or
replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount
equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty,
repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products
were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate
modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall
not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or
electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice,
recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above
warranty.
See http://www.omron.com/global/ or contact your Omron representative for published information.
Suitability of Use.
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the
combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable
third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself
is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine,
system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product
with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE
QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
Programmable Products.
Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence
thereof.
Performance Data.
Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining
suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate
it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.
Change in Specifications.
Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our
practice to change part numbers when published ratings or features are changed, or when significant construction changes are
made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers
may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at
any time to confirm actual specifications of purchased Product.
2023.12
In the interest of product improvement, specifications are subject to change without notice.
OMRON Corporation
Industrial Automation Company
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2023 All Right Reserved.