Professional Documents
Culture Documents
DS RVT50HQLNWC00 Rev 1 0-3179763
DS RVT50HQLNWC00 Rev 1 0-3179763
RVT50HQLNWC00
HB, IPS LVDS 5.0'' LCD TFT DATASHEET
Rev.1.0
2022-11-23
REVISION RECORD
CONTENTS
REVISION RECORD ................................................................................................................................... 2
CONTENTS ...................................................................................................................................................... 3
MODULE CLASSIFICATION INFORMATION ............................................................................... 4
uxTouch ASSEMBLY ................................................................................................................................. 5
MODULE DRAWING ................................................................................................................................. 6
ABSOLUTE MAXIMUM RATINGS ....................................................................................................... 7
ELECTRICAL CHARACTERISTICS ...................................................................................................... 7
BACKLIGHT ELECTRICAL CHARACTERISTICS .......................................................................... 7
ELECTRO-OPTICAL CHARACTERISTICS ....................................................................................... 8
BLOCK DIAGRAM ................................................................................................................................ 10
INTERFACES DESCRIPTION .......................................................................................................... 10
INSPECTION ............................................................................................................................................ 16
uxTouch ASSEMBLY
uxTouch are LCD TFT displays with specially designed projected capacitive touch panels.
uxTouch display can be mounted without any holed in the housing. Our standard uxTouch
displays include double-sided adhesive tape (DST) to stick TFT easily to the housing. Basic
series include 4.3”, 5.0”, 7.0” and 10.1” display sizes.
uxTouch models with double-side adhesive tape (PN with endings 00, 01, 03, 04) can be
mounted by connecting the glass to the housing. Riverdi recommends using support
brackets assembled to display’s back. An additional support will stiffen the whole structure
and minimize the influence of external factors such as vibration. Figure 1 below show
examples of using support elements.
10.74 [0.423]
11.14 [0.439]
13.00 [0.512]
13.70 [0.539]
14.00 [0.551]
110.00 [4.331](SENSOR A.A.) 13.00 [0.512] MAX 5.40 [0.213](MOULE O.D.)
108.60 [4.276](CG V.A.) 13.70 [0.539] 2.45 [0.096](CG+SCA+SENSOR+DST)
108.00 [4.252](TFT A.A.) 14.00 [0.551] 1.275 [0.050](CG+DST) DOUBLE-SIDED TAPE
7] 3M9495 T=0.175mm[0.007inch]
68.00 [2.677]
[ R0.19 1.10 [0.043](CG)
5.00
4*R
C
46.40 [1.827]
66.80 [2.630](SENSOR A.A.)
74.80 [2.945](SENSOR O.D.)
LENS
(T=1.1mm[0.043inch])
SCA
(T=0.2mm[0.008inch])
SENSOR
(T=0.55mm[0.022inch])
DST
(T=0.6mm[0.024inch])
5.00 [0.197]
BLACK MASK PRINTING
47.50 [1.870]
COMPONENT
49.40 [1.945]
64.70 [2.547]
COMPONENT
MAX 1.50 [0.059]
RAL9005 AREA
43.14 [1.698]
AREA
58.44 [2.301]
34.00 [1.339]
5.00 [0.197] STIFFENER
COMPONENT
AREA MAX 1.70 [0.067]
24.94 [0.982]
MAX 3.50 [0.138]
1 40
1 4
CONTACT 40 1
CN1
STIFFENER
SIDE
22.56 [0.888]
41.24±0.5 [1.624±0.020]
JST SM04B-SRSS-TB
0.20 [0.008]*45° 10 1
1 40 1 4 0.20 [0.008]*45° LEDA LEDK
2*0.50 [0.020] 2*0.50±0.1 [0.020±0.004]
3.50±0.3 [0.138±0.012]
CN1
4.00 [0.157]
ELECTRICAL CHARACTERISTICS
PARAMETER SYMBOL MIN TYP MAX UNIT
Power Supply for analog circuit VDD 3.0 3.3 3.6
Logic Input Low Voltage VIL 0 - 0.3VDD
Voltage High Voltage VIH 0.7VDD - VDD V
Logic Output Low Voltage VOL - - GND+0.4
Voltage High Voltage VOH VDD - 0.4 - -
Power Black Mode Pb - 80 100 mA
Consumption Standby Mode Pw - 40 50 µA
Note 2. The recommended operating conditions refer to a range in which operation of this
product is guaranteed. The operation cannot be guaranteed if the absolute maximum
values exceed.
Note 3. If LED is driven by high current, high ambient temperature and humidity
condition, the lifetime of LED will be reduced. Operating life means brightness goes down
to 50% initial brightness. Typical operating lifetime is estimated data.
ELECTRO-OPTICAL CHARACTERISTICS
ITEM SYMBOL CONDITION MIN TYP MAX UNIT RMK NOTE
Response Time Tr+Tf - 30 40 ms FIG 2. 4, 7
Contrast Ratio Cr 800 1000 - --- 1, 7
θ=0°
Luminance δ
∅=0° 75 80 - % 3, 7
Uniformity WHITE FIG 3.
Ta=25 °C
Surface
Lv - 800 - cd/m2 2, 7
Luminance
∅ = 90° - 80 - deg
Viewing Angle ∅ = 270° - 80 - deg
θ FIG 4. 6
Range ∅ = 0° - 80 - deg
∅ = 180° - 80 - deg
Rx 0.575 0.615 0.655 -
Ry 0.296 0.336 0.376 -
Gx 0.352 0.392 0.432 -
θ=0°
CIE (x, y) Gy 0.512 0.552 0.592 -
∅=0° FIG 3. 5,7
Chromaticity Bx 0.100 0.140 0.180 -
Ta=25 °C
By 0.085 0.125 0.165 -
Wx 0.274 0.316 0.358 -
Wy 0.294 0.336 0.378 -
Note 1. Contrast Ratio (CR) is defined mathematically as below, for more information see
Figure 3.
Average Surface Luminance with all white pixels (P1, P2, P3, P4, P5)
Contrast Ratio =
Average Surface Luminance with all black pixels (P1, P2, P3, P4, P5)
Note 2. Surface luminance is the LCD surface from the surface with all pixels displaying
white. For more information see Figure 3.
Lv = Average Surface Luminance with all white pixels (P1, P2, P3, P4, P5)
Minimum Surface Luminance with all white pixels (P1, P2, P3, P4, P5)
δ WHITE =
Maximum Surface Luminance with all white pixels (P1, P2, P3, P4, P5)
Note 4. Response time is the time required for the display to transition from white to black
(Rise Time, Tr) and from black to white (Decay Time, Tf). For additional information see
Figure 2. The test equipment is BM-7A.
Note 5. CIE (x, y) chromaticity, the x, y value is determined by measuring luminance at each
test position 1 through 5, and then make average value.
Note 6. For TFT module, viewing angle is the angle at which the contrast ratio is greater 10.
The angles are determined for the horizontal or x axis and the vertical or y axis with respect
to the z axis which is normal to LCD surface. For more information see Figure 4.
Note 7. Viewing angle is measured at the center point of the LCD by CONOSCOPE (ergo-
80). For response time testing, the testing data is based on BM-7A. Instruments for
Contrast Ratio, Surface Luminance, Luminance Uniformity, Chromaticity the test data is
based on SR-3A.
A: 5mm
B: 5mm
H, V: Active Area
Light spot size ∅=5mm, 500mm distance
from the LCD surface to detector lens.
Measurement instrument is SR-3A
Figure 3. Measuring method for Contrast ratio, surface luminance, Luminance uniformity,
CIE (x, y) chromaticity
BLOCK DIAGRAM
INTERFACES DESCRIPTION
TFT assignment
Matched Riverdi ZIF connector: ZIF0540UH
25 GND P Ground
26, 27 NC - No connection
6-bit /8-bit mode select.
28 SELB I Set ‘LOW’ for 6-bit data input mode,
Set ‘HIGH’ for 8-bit data input mode (Default)
29 NC - No connection
30 GND P Ground
31, 32 LED- P Backlight LED Cathode
33 L/R I Horizontal inversion
Note 1
34 U/D I Vertical inversion
35-38 NC - No connection
39, 40 LED+ P Backlight LED Anode
Note 1. U/D L/R Function Description
CON1 assignment
Matched PCAP USB programing cable accessory: RVA-PCAP-USB-CABLE
Note 1. If USD_VDD of CON1 is powered, please make sure to disconnect the PCAP FPC
from the PCAP ZIF connector on your application.
Otherwise, there is a risk that the LDO on the PCAP FPC will be destroyed.
TIMING CHARACTERISTICS
System bus timing for LVDS interface
12.1.1 4Lane VESA Data Format Color Bit Map
8-bit LVDS input mode, SELB=’H’
Timing Table
PARAMETER SYMBOL MIN TYP MAX UNIT
DCLK Frequency Fclk 23 25 27 MHz
Period Time Th - 816 896
Display Period Thdisp 800
HSYNC Hsync Back Porch Thbp - 8 48 DCLK
Hsync Front Porch Thfp - 8 48
Hsync Pulse Width Thw - 4 8
Period Time Tv - 496 504
Display Period Tvdisp 480
VSYNC Vsync Back Porch Tvbp - 8 12 HSYNC
Vsync Front Porch Tvfp - 8 12
Vsync Pulse Width Tvw - 4 8
Electrical characteristics
DESCRIPTION SPECIFICATION
Power Consumption (IDD) Active Mode 90 mA
Sleep Mode 10 mA
Linearity +/- 1.5mm
Controller ILI2132A
Resolution 800 x 480
INSPECTION
Standard acceptance/rejection criteria for TFT module
Inspection condition
Ambient conditions:
• Temperature: 25 ± 2°C
• Humidity: (60 ± 10) %RH
• Illumination: Single fluorescent lamp non-directive (300 to 700 lux)
Inspection standard
ITEM CRITERION
3.5” ≤ Size ≤ 5”
3.5” ≤ Size ≤ 5”
RELIABILITY TEST
NO. TEST ITEM TEST CONDITION NOTE
1 High Temperature Storage 80°C/120 hours
2 Low Temperature Storage -30°C/120 hours
3 High Temperature Operating 70 °C /120 hours Note 1
4 Low Temperature Operating -20°C/120 hours
Humidity 40°C, 90%RH,
5 High Temperature and High Humidity
120Hrs
-20°C for 30min, 70°C for 30
min.
6 Thermal Cycling Test (No operation)
100 cycles. Then test at room Note 2
temperature after 1 hour
Frequency: 10 ÷ 55 Hz.
Stroke: 1.5 mm.
Sweep: 10Hz ÷ 55Hz ÷ 10 Hz.
7 Vibration Test
2 hours for each direction of X,
Y, Z
(Total 6 hours)
Height: 60 cm
8 Package Drop Test
1 corner, 3 edges, 6 surfaces
±2KV, Human Body Mode,
9 Electrostatic Discharge
100pF/1500Ω
Note 1. Sample quantity for each test item is 5 ÷ 10 pcs.
Note 2. The device is kept at room temperature for 2 hours prior to starting the test.
LEGAL INFORMATION
CE marking is usually obligatory only for a complete end product. Riverdi display modules
are semi-finished goods which are used as inputs to become part of the finished products.
Riverdi grants the guarantee for the proper operation of the goods for a period of 12 months
from the date of possession of the goods. If in a consequence of this guaranteed execution
the customer has received the defects-free item as replacement for the defective item, the
effectiveness period of this guarantee shall start anew from the moment the customer
receives the defects-free item.
Information about device is the property of Riverdi and may be the subject of patents
pending or granted. It is not allowed to copy or disclosed this document without prior
written permission.
Riverdi endeavors to ensure that all contained information in this document is correct but
does not accept liability for any error or omission. Riverdi products are in developing process
and published information may be not up to date. Riverdi reserves the right to update and
makes changes to Specifications or written material without prior notice at any time. It is
important to check the current position with Riverdi.
Images and graphics used in this document are only for illustrative the purpose. All images
and graphics are possible to be displayed on the range products of Riverdi, however the
quality may vary. Riverdi is no liable to the buyer or to any third party for any indirect,
incidental, special, consequential, punitive, or exemplary damages (including without
limitation lost profits, lost savings, or loss of business opportunity) relating to any product,
service provided or to be provided by Riverdi, or the use or inability to use the same, even if
Riverdi has been advised of the possibility of such damages.
Riverdi products are not fault tolerant nor designed, manufactured or intended for use or
resale as on line control equipment in hazardous environments requiring fail–safe
performance, such as in the operation of nuclear facilities, aircraft navigation or
communication systems, air traffic control, direct life support machines or weapons
systems in which the failure of the product could lead directly to death, personal injury or
severe physical or environmental damage (‘High-Risk Activities’). Riverdi and its suppliers
specifically disclaim any expressed or implied warranty of fitness for High-Risk Activities.
Using Riverdi products and devices in 'High-Risk Activities' and in any other application is
entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless
Riverdi from all damages, claims or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Riverdi intellectual property rights.
Authorized Distributor
Riverdi:
SM-RVT50HQLNWC00