Professional Documents
Culture Documents
Lubrication
Lubrication
Boundary
(i) fluid film thickness basically molecular 10-7cm
(ii) depends on molecular properties of lubricant and solid members, often chemical
( E.P. additives actuated by high temperature generated by rubbing)
(iii) independent of shape and velocity in so far as these influence the temperature
generated from rubbing.
(iv) obeys classical laws of friction
(v) Frictional coefficient = 0.05 to 0.1
Hydrodynamic
i) self acting (i) fluid thickness 1 mm to 0.01 mm
(ii) Depends on the viscosity of the lube oil and the shape and relative motion of the
solid surfaces
(iii) Independent of properties of the solid members; so long as the elasticity does not
deform the shape. and thermal properties do not effect the temperature of the
lubricant
(iv) does not obey classical friction laws.
(v) Friction coefficient = 0.001
(vi) film may form by self action or by Hydrostatic pressure of the lube oil.
Hydrodynamic
-externally pressurised as above except the separation of surfaces is caused by fluid being
injected under pressure
Elastohydrodynamic
This is the type of lubrication used with rolling element bearings. To clarify, the material of
the running surface deforms under high pressure as the rolling element passes over it. The
oil wedge forms in this deformation.
(i) Deformation and increased viscosity with pressure are involved
(ii) Frictional coefficient = 0.05
(iii) film thickness less than Hydrodynamic
Oil distribution within a journal bearing
n = e / Cr
Factors involved with the eccentricity factor n are; minimum oil film thickness, journal
attitude angle, pressure distribution, peak pressure angle, friction, horsepower loss and oil
flow through the loaded region. The latter three determine the temperature of the bearing
which for high speed bearings can be a limiting factor.
Lube Oil requirements for Diesel Engines
Crankcase
The oil has to serve two purposes;
1. reduce friction
2. Cool bearings
A good quality mineral oil will serve the purpose of reducing friction to an acceptable level
depending upon the metals involved and other conditions such as temperature. All oils will
oxidise and this reduces its effectiveness as a lubricant. Oxidation will also cause deposits
that can block passageways and coat working parts. The rate of oxidation will depend upon
temperature, the higher the temperature the more rapid the rate. Anti oxidants are
available which reduce the rate, also additional properties can be achieved by the use of
additives.
Under high temperatures oil is liable to thermal degradation that causes discoloration and
changes the viscosity. Additives cannot change an oils susceptibility to this degradation.
The refining process can remove compounds that effect the thermal stability of the oil and
also those that lower oxidation resistance. Most of the chemicals found in oil will react
more or less with oxygen, The effects of this oxidation is always undesirable. Hence, a
major objective of the refining process of a mineral oil is to remove those hydrocarbons i.e.
the aromatics, the small amount of unsaturates together with molecules containing sulphur,
oxygen and nitrogen.
Unfortunately these same molecules are those that improve the boundary lubrication
performance. Hence, a careful balance must be struck. The use of anti-oxidants makes a
slightly better balance although there usefulness is limited.
Tin based white metal is susceptible to hardening as an oxide layers from on the surface.
These tin oxides are a grey-black in appearance and are extremely hard. There formation
reduces the bearing clearance, as the oxide layer is thicker than the original white metal
material from which it formed. The oxide has a lower coefficient of friction than the
original white metal but it will cause problems if it brakes up as fragments will become
embedded edge on in the white metal and can score the pin.
Contamination
Water
Water from:
1. bilge's
2. Jackets
3. Sea via coolers
4. leaky seals or washing in purifiers
5. Condensation
Problems caused by water contamination:
Water leads to corrosion especially if there is sulphur present due to fuel
contamination
forms emulsions which are not capable of withstanding high loads
removes water soluble additives when centrifuged out
leads to possible bacterial attack
Fuel
May be heavy residual or light diesel/gas oil and can be sourced to faulty to cylinder
combustion or faulty seals on fuel p/ps.
Problems
Increases viscosity for HFO, reduces viscosity for D.O.
reduces flashpoint
Introduces impurities such as sulphur
dilutes lub oil when in large quantities
Solid impurities
i.e. carbon from the cylinder combustion process, particularly of importance with trunk
piston engines but also for crosshead engines with inefficient diaphragm. The carbon can
lead to restrictions and blockages of oil ways causing bearing failure. Straight mineral oils
hold 1% carbon in suspension, dispersant oils hold about 5%.
Bacterial attack
Certain bacteria will attack oil but water must be present. The bacteria may exist in a
dormant state in the oil but water is required if they are to reproduce.. The bacteria digest
the oil causing breakdown emulsions to be formed, acidity increases, dead bacteria block
filters and corrosive films form on working surfaces.
Two other factors which encourage the growth are a slight acidity in the water (pH 5 or 6)
and a slightly raised temperature (20 to 40oC) which can lead to rapid growth.
Biocide additives are available but they are not always compatible with other desired
additives and can lead to large organic blockages if treated in the machinery. The best
solution is to avoid the presence of water. If mild attack takes place the oil may be heated
in the renovating tank to above 90oC for 24hrs before being returned to the sump via the
centrifugal separator. For a severe attack the only solution is complete replacement of the
charge followed by sterilisation of the system. It may be noted that on replenishment the
bacteria may be present in a dormant state in the new charge.
Insoluble Sediments - basically the result of wear and oxidation, corrective action at 1% by
weight
Ash - a measure of incombustibles in the oil sample, corrective action at 0.13% by weight
TAN – (Total Acid Number) - consists of the strong acids (mainly sulphuric acid) formed in
the combustion process and weak acids resulting form oxidation of the lub oil.
SAN – (Strong Acid Number) - the oil should be renewed if any is detected
TBN – (Total Base Number) - indicates the alkaline reserve particulary important for trunk
piston engines
Closed flash point - highlightd fuel contamination, corrective action if reduces by 30oC from
new
When running in, the cylinder lube oil injector pumps may be filled with a a straight
mineral oil without anti-wear properties- typically the crankcase oil- once this small reserve
of oil is exhausted, running in carries on with normal cylinder lube oil. The flow of oil is
increased to carry away metallic particles.
Low speed engines are particularly at risk from crankcase lubricant contamination caused
by cylinder oil drainage past the piston rod gland and combustion products. This can lead to
severe damage of engine crankcase components and reduction of life of oil which is
normally expected to last the lifetime.
There has been a general increase in the viscosity and Base number of crankcase oils over
recent years particularly for engines built since the early 1980's. Increased alkalinity,
viscosity and insolubles, fuel derived elements such as vanadium and oil additive derived
elements such as calcium, suggest that the contamination is from the cylinder oil drainage.
Deterioration of the crankcase oil has led to the expensive necessity of replacing up to 50%
of the sump, this is particularly of concern as it is often only a temporary measure.
The thicker the oil film the greater the cushioning against shocks. Also less tendency for pit
formation by hydraulic action in cracks,
Turbine oil
Compromise between above two requirements
Generally a good quality refined mineral oil derived from paraffanic base stock used
with various additives including EP additives for highly loaded gearing.
Anti-foaming properties important
Additives
Improvements in lubricating oil over the last twenty years have come about almost entirely
from the use of additives.
These are added for three main reasons;
1. to protect the lubricant in service by limiting the chemical change and deterioration
2. To protect the mechanism from harmful combustion products and malfunctioning
lubricating oil
3. To improve existing physical properties and to create new beneficial characteristics
in the oil
Typical additives are; Barium, calcium, phosphorus, Sulphur, chlorine, zinc, oxidation
inhibitor-increases oil and machinery life, decreases sludge and varnish on metal parts
Corrosion inhibitor-protects against chemical attack of alloy bearings and metal surfaces.
Antiwear improvers-protects rubbing surfaces operating with this film boundary lubrication.
One such antiwear ( and oxidation inhibitor) chemical is Zinc dithiophosphate or ZDDP
Detergent-tend to neutralise the deposits before formation under high temperature and
pressure conditions, or as a result of using a fuel with high sulphur content. The principle
detergents are soaps and alkaline metals, usually calcium ( often referred to as 'metallo-
organic compounds'). They are usually ash forming and spent additive will contribute to the
insolubles loading of a used oil. It should be noted that additives which do not burn cleanly
without ash tend to be avoided for use with Cylinder Lubricating Oils.
Dispersant-used to disperse or suspend the deposits forming contaminants. Typical
dispersants, such as polyesters and benzlamides, are usually clean burning. The molecules
have a polar charge at one end which attracts and holds the deposits
Alkaline agents-neutralises acids, these form the TBN of the oil and includes additives such
as the above dispersants and detergents. An excess of acid neutralising alkalis are present
in the oil and these help to keep parts clean. Failure to keep an oil alkaline can lead to
damage to bearings due to acidic attack as well as increased liner wear.
Rust inhibitors-
Pour point depressants-improves low temperature viscosity
Viscosity Improvers - an additive that improves the viscosity index of the oil. I.e. reduces
the effect of temerpature of=n the viscosity of the oil. Shear stability property is measured
indicating the effect of high rates of shar on the VI improver as the improver molecules are
broken down into smaller molecules
Antiseptic-bactericide.
Oxidation
Oxidation degrades the lube oil producing sludges, varnishes and resins. Presence of
moisture, and some metals particularly copper tend to act as a catalyst. Once oxidation
starts, deterioration of the properties of the oil is rapid.
Recharging
When recharging no more than 10 % of the working charge should be topped up due to
heavy sludgeing that can occur due to the heavy precipitation of the sludge.
EP additive oils
Can assist in healing of damaged gear surfaces but should be used as a temporary measure
only due to risk of side effects
Emulsification
This occurs due to water contamination; also, contamination with grease, fatty oils,
varnish, paint and rust preventers containing fatty products can also promote
emulsification.
The presence of an emulsion can be detected by a general cloudiness of the sample. Salt
water emulsifies very easily and should be avoided.
Water entrained in the oil supplied to a journal bearing can lead to loss of oil wedge, rub
and failure.
Fresh water contamination whilst not in itself dangerous can lead to rusting. The iron
oxides catalyses the oil to form sludge's. The additives in the oil can leach out to change
the water into an electrolyte.
Salt water contamination is very serious as it causes tin oxide corrosion, and also leads to
electrochemical attack on the tin matrix in the white metal. The sea water act as then
electrolyte.
A major problem of water within a lub oil is where the mix enters a bearing, here it is
possible for the water to be adiabatically heated causing it to flash off collapsing the oil
wedge.
Acid Stress- Caused by sulphuric and oxidation acids. This leads to increased corrosive wear,
deposits, reduced Base Number and shorter oil life. Rapid depletion of the BN is the
clearest sign of oil stress
Asphaltene Stress-This caused by fuel contamination of the lube oil and can lead to
increased levels of deposits, sludges, lacquers, oil thickening and reduced oil life. In
addition deposits on the under crown side of the piston can lead to increased hot corrosion
on the piston.
OIL ANALYSIS
Regular testing of crankcase lub oil is important to ensure that deterioration has not taken
place. The results of in service deterioration could be a reduction in engine protection or
actual attack on working points by corrosive deposits. Oil samples are generally tested
every 3 to 4 months depending on the system and experience. Shipboard testing is taking a
rising prominence to allow monitoring of oil condition between testing.
To ensure good representation, care should be taken where the sample is drawn
Correct
Main supply line
inlet or outlet from l.o. cooler
Outlet from main l.o. pump
Incorrect
standpipes
purifier outlet
purifier direct sump suction
Viscosity
The viscosity is the most important property of the oil. Oil of correct viscosity will provide
optimum film strength with minimum friction losses and leakage.
The viscosity of a L.O. may fall due to fuel dilution if running on gas oil, and rise if running
on heavy f.o. Viscosity may also increase due to heavy soot loading if purifiers and filters
not operating efficiently. Oil ageing caused by oxidation and thermal degradation increases
viscosity.
A simple shipboard test is the Mobil flow stick where drops of new and used oil are placed
in separate channels on an inclined 'stick'. The rate the oil flows down the stick is
proportional to its viscosity.
Water content
Initially determined by 'crackle' test. The presence of Na and Mg in a 4:1 ratio indicates salt
water contamination.
Limits are laid down by the manufacturer, but as a rule of thumb a limit of 0.2% should
cause investigation into source and remedial action at 0.5%
Gross contamination can be remedied by placing the charge in a separate tank and heating
to 70oC and circulating through purifier.
Spectrometry
Indicates the presence of metal element composition and identifies additive and
contaminant levels.
Zinc(Zn),Phosphorus(P)- are components of many oils such as diesel engine oils, hydraulic
oils and gear oils, to enhance antiwear and over properties of the oil
Magnessium(Mg)- as for Ca, may also be due to sea water contamination if found in Ratio of
1:4 of Na
Aluminium(Al)- generally comes from wearing piston skirts, levels rise where new piston
fitted to old engine. Typically 10ppm, but rises during bedding in. May also indicate the
presence of catylytic fines in residual fuels.
Iron(Fe), Molybdenum(Mo), Chromium(Cr)- metals alloyed for piston ring etc, a rise in level
may indicate ring pack/liner wear.
Copper(Cu), Lead(Pb) , Tin(Sn), Silver(Ag) - soft metals used in the overlay of shell
bearings, and phosphor bronze gears.Note that high copper content can also occur when
samples are drawn from copper pipes which have not been flushed as well as gear wear.
For crosshead engines the TBN will tend to rise due to contamination by liner lubrication, it
should not be allowed to raise more than twice that of the new charge.
A simple shipboard go,no-go test is available for measuring the TBN, it involves the addition
of an indicator and acid reagent to a 30ml sample. The quantify of acid reagent added is
determined by the required level of TBN, for TBN2.5 0.5ml are added, for TBN20 4ml is
added. After three minutes the colour is checked against a chart
TAN-TOTAL ACID NUMBER-measure of organic acid and strong acid content of oil. Where
SAN is nil, the TAN represents the acidity in the oil due to both the acids in the additives
and the oxidation of the hydrocarbons in the oil. The TAN of fresh oils varies with oil type,
and tends to climb with age. A high TAN may indicate that an oil should be changed or
freshened by top up. A high TAN may be accompanied with increased viscosity.
Oil cleanliness
IC-INDEX OF COMBUSTION-measures soot loading of oil
DP-DEMERIT POINTS- combination of IC and MD: the lower the value, the healthier is the
condition of the oil
Shipboard water content test
The mechanism of oil whirl can be explained by referring to the diagram below.
Under normal operation, the shaft of the machine will rise up the side of the bearing
slightly. How far the shaft will rise depends on shaft RPM, rotor weight and oil pressure.
The shaft, operating at an eccentric position from the bearing centre, draws oil into a
wedge to produce a pressurised load bearing film. If the eccentricity of the shaft within the
bearing is increased from this normal operating position, say be external shock or load
transient, additional oil will immediately be pumped in to fill the space vacated by the
shaft thus increasing the oil film supporting the shaft. This oil film may drive the shaft in a
whirling motion around the bearing. If damping in the design is sufficient then the system
will return to its original position otherwise the whirling motion will continue.
Alternately, a lightly loaded bearing may rise under normal conditions reducing the
clearance above the bearing to a point where an oil wedge forms forcing the shaft back
down. In doing so the clearance is restored at the top of the bearing and the oil wedge fails
removing the downward pressure.
Steam Turbine bearings are susceptible to oil whirl as they tend to have larger than normal
clearances to allow for high oil flows for cooling.
Causes
This is achieved by machining the two shells whilst shims are fitted between the faces
Grooved
Camella